C/O Civil Hospital building at Palampur Distt. Kangra (HP) (SH- Providing Fire fighting system therein)

Amount

Providing, fixing, testing and commissioning of MS air cushion tank on top of each riser fabricated form 6mm thick MS plate, 250mm in diameter and 1.2 m in height with dished ends fabricated from 8mm thick MS plate with Air release valve with stop cock, flanged inlet connection and drain arrangement with 25mm dia valve, pressure gauge with gun metal stop cock complete with all accessories as required in all respect and to the best satisfaction of Engineer-in-Charge.

Makes:- Zoloto/Sant/Leader.

Providing, fixing, testing and commissioning of Perched air vessel (size 450 mm dia & 2000 mm height) for pressurization of hydrant / sprinkler system complete with adequate pressure switches (as per design / requirement) with valves to operate as per operating sequences including 25 mm dia drain valve, air release valve with stop cock on the top, minimum 50 mm dia inlet with isolating valve duly painted from inside and outside with two coats of synthetic enamel paint over a coat of primer complete as required and Suitable cement concrete foundation with plaster, along with all neccessory floor supporting stand and foundation arrangement.(Vessel should be suitable for rated working pressure) as required complete in all respects and to the best satisfaction of Engineer-in-charge.

Makes:-Zoloto/Sant/Leader.

Providing, laying, jointing, testing and commissioning of following sizes of MS 'C' Class (Heavy duty) pipes conforming to IS-1239 with all fittings (standard MS fitting with welded joint shall be used on the pipes) including tees, elbows, reducers, union, flanges, rubber gaskets, GI nuts bolts, washer including supporting/fixing the pipe on floor / wall /ceiling with clamps, hangers (using anchor fastners) as per specification. including cutting holes and chases in brick, RCC work and making good the same to original conditions complete in all respects. All hangers, clamps, brackets etc. shall be of iron unless specified otherwire and then supply of the same shall also be included for rates under this head. Welding of any kind on the galvanized support / hanger shall not be permitted including synthetic enamel paint of approved shade over a coat of zinc primer.Priorto application of primer the surface should be cleaned dirt,rusts,rough substance etc. as required complete in all respects and to the best satisfaction of Engineer-in-charge.

25mm dia pipe

80mmdia pipe

100mm dia pipe

150mm dia pipe

200mm dia pipe

Makes:- Jindal/B.S.T./Surya Tube.

Providing two coats of synthetic enamel paint of approved shade over a coat of primer. Prior to application of primer the surface should be cleaned for any dirt, rusts, rough substance etc. Including painting of legends both direction arrow as per the approval of the Project Manager as required complete in all respects and to the best satisfaction of Engineer-in-charge.

25mm dia pipe

80mmdia pipe

100mm dia pipe

150mm dia pipe

200mm dia pipe

Providing & Fixing of burden type Stainless Steel dial type pressure gauge with brass isolation valve and pipe of 100 mm dia with Caliberation: 0-20 Kg/cm2 as required complete in all respects and to the best satisfaction of Engineer-in-charge.

Make:H. Guru/ Bell/Fiebg.

Providing & fixing Gun metal fire hydrant single headed landing valve with 80 mm N.B. flanged inlet, s.s spindle controlled 63 mm dia female instantaneous outlet type. SS coupling, blank cap, chain, twist release type lug & all accessories Conforming to IS standards as required complete in all respects and to the best satisfaction of Engineer-in-charge.

Make: Minimax/CeaseFire/ Tyco

Providing & Fixing of 63 mm dia 15 m long non-percolating flexible hose (RRL- type A) as per IS : 636. Type A with Gun Metal male & female instantaneous type coupling (IS 903) (For internal and External hydrant system) as required complete in all respects and to the best satisfaction of Engineer-in-charge.

Make: Minimax/CeaseFire/ Tyco

Providing and Fixing Gun Metal 63 mm dia instantaneous pattern branch short pipe, 20 mm dia nozzle conforming to IS 903, suitable for inter connection to hose pipe coupling as required complete in all respects and to the best satisfaction of Engineer-in-charge.

Make: Minimax/CeaseFire/ Tyco

Providing & fixing ball valve 25mm dia. as required complete in all respects and to the best satisfaction of Engineer-in-charge.

Providing & fixing of Bitumein sheet 4mm thick (pipekot) wraping & coating for underground pipe150 mm dia. as required complete in all respects and to the best satisfaction of Engineer-in-charge.

Make Shalimar/WTL or equivalent

Providing & Fixing of wall mounting swinging type first aid fire hose reel with drum, hanging bracket, 36.5 Mtr. length x 20 mm dia high pressure hose reel tubing as per IS: 444 with gun metal (GM) shut off nozzle having 5 mm dia orifice. The hose reel shall be conforming to IS : 884-1985. Rate shall include 25 mm dia M.S. pipe connection from Riser to hose reel, sockets, nipples, elbows and ball valve (25 mm dia). Drum shall be fixed on adjoining wall through anchor fasteners / cement concrete block as and when required complete in all respects and to the best satisfaction of Engineer-in-charge..

Make: Minimax/CeaseFire/ Tyco

Weather proof standard fire hose cabinet made of 18 SWG powder coated fibre. sheet having single or double opening glazed (3.0 mm thick glass) shutter including necessary locking arrangement by allan key, stove enamelled Fire red finish (as per IS : 5, shade no. 536) with " Fire Hose" marked on front, suitable for housing 2 nos. 15m long 63 mm dia Hose pipe, 1 No. branch pipe & nozzle spanner as required complete in all respects and to the best satisfaction of Engineer-in-charge.

Make: Minimax/CeaseFire/ Tyco

Providing Cast iron /steel Butterfly Valve Confirming to type P.N 1.6 of I.S 13095-1991 Complete with Flanges bolt, nuts, gasket etc. As per table 'E' specification complete in all respect hydraulically test to 20 K./sqcm. as required complete in all respects and to the best satisfaction of Engineer-in-charge.

80 mm Dia

100 mm Dia

150 mm Dia

Providing and fixing Cast Iron dual plated Check Valve (NRV) horizontal type with gunmetal seat non-return valve confirming to class - I of IS : 5312 including nuts, bolts, 1.5 mm thick compressed asbestos gasket as per table "E" and specifications as required complete in all respects and to the best satisfaction of Engineer-in-charge.

80 mm Dia

100 mm Dia

150 mm Dia

Providing & fixing Gunmetal Collecting head inlet connection to external hydrant ring/hydrant riser with 4 Nos. 63 mm dia instantaneous type inlet and 150 mm dia flanges outlet conforming to IS:904 with blank cap and chain.

Make: Minimax/CeaseFire/ Tyco

Supply, installation, testing and commissioning of electrically driven high pressure centrifugal fire hydrant / sprinkler pump, suitable for automatic operation consisting of the following:

(a).Multistage Multi-outlet, centrifugal pump (Flow :2280 LPM and Head : 70mtr), suitable for operation on 415 volts ± 10 %, 3 phase, 50 HZ A.C supply. The installation shall be complete with flexible coupling and coupling guard as required. Fire pump shall have C.I. casing, CS diffusers, bronze impeller (hard finished and dynamically balanced) and S.S. (410) Shaft with mechanical seal, capable for delivering the required flow at the required head to ensure a minimum pressure of 3.5 Kg/Sqcm at the farthest or topmost hydrant / sprinkler. The installation shall be complete with necessary pressure gauge with gun metal shut off cock on delivery side.(b).Squirrel cage induction motor, TEFC type suitable for operation on 415 volts, 3 phase 50 HZ A.C supply, for the above pump with synchronous speed of 2900 RPM, conforming to IP 55 protection & class F insulation. The motor shall conform to IS 325-1978 (up to date) with flexible coupling and coupling guard, complete as required.Common base plate for (a) and (b) from G.I.Channel for required size.(d)d) Suitable RCC pump-Foundations as per manufactures design and 4 nos Dunlop (cushy foot) heavy duty Antivibration mounting pads.

Make:- Kirloskar/Siemens

Supply, installation, testing and commissioning of Diesel Engine driven fire pump suitable for automatic operation comprising of the following and conforming to BS 649/IS 10002 all amended upto date.

A) Horizontally mounting,centrifugal type single/multi-stage fire pump having cast ironbody, bronze impeller,stainless steel shaft &capable of delivering 2280 LPM against a total head of 70M complete withnecrssary Y stainer on the sunction side and pressure gauge with stop cocks etc. on the delivery side including bybass arrangement (with 50mm dia GM stop valve and upto 5mGI stop valve and upto 5M GI medium pipe) for perodical testing of thepumping set of the pumping set as per TAC rules. b) Water cooled TAC approved Diesel Engine suitable for the developing at least 62BHP at 2150RPM for above pumping complete with autmatic starting mechanism, batteries,automatic battery charger unit,flexble coupling withthe pump,coupling with the pump,fuel tank,silencer,exhaust pipe with insulation appro. 25m length& all standard accessories as requrid asper TAC rules including earthing,mandatory spares and tool kit. c) Common bed plate for mounting pump and Engine fabricated of suitable MS channel as per manufacturer recommendations. d)Suitable RCC pump foundation as per manufacture design 8Nos Dunlop Anti-vibration(cushy foot) heavy duty mounting pad.

Make:- Kirloskar/Siemens / Grund foss

Supply, installation, testing and commissioning of jockey pump (pressurisation pump) comprising of the following:

(a)Horizontal pump(Flow :180 LPM and Head : 70mtr) suitable for operation on 415 volts ± 6%, 3 phase, 50 HZ A.C supply. The installation shall be complete with Flexible coupling and coupling guard, complete as required.The pump casing shall be CI, shaft shall be SS & impeller/ shaft sleeve/casing wearing ring shall be bronze. The pump shall be provided with mechanical seal The system shall be complete with necessary pressure gauge with gun metal shut off cock on delivery side. b)Squirrel cage induction motor totally enclosed fan cooled type suitable for 415 volts +10%-10% 3 phase 50HZ AC supply of suitable capacity(appro10 KW) for the above pump with synchronous speed of 1500/3000 RPM confirming to IS325 &duly coupled with above pump coupled with flexible coupling including earthing as per relevant Indian Standard and specification. c) Common bed plate for mounting pump and Motor fabricated of suitable MS channel as per manufactures recommendation. d)Suitable RCC pump foundation as per manufactures design Dunlop 4 Nos Dunlop Anti-vibration (cushy foot) heavy duty mounting pads.

Make:- Kirloskar/Siemens / Grund foss

Supply, installation, testing and commissioning of Pressure switch for fire pumps of approved make,including necessary wiring and cut off valve up to central panel & other material as described in specifications.

Make:- Indfoss /System Sensor / Grundfoss

Makes:- Advance/Delight Power Control or equivalent.

Excavation in foundation, trenches etc. in earth work, lift upto 1.50 meters stacking the excavated soil not more than 3 meters clear from the edge of excavation and then returning the stacked soil in 15 cm layers, when required into plinths sides of foundations etc. consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth as directed with in a lead of 20 meters complete in pick and jumper work.

Providing and laying of one No. aluminium conductor, PVC insulated and PVC sheathed, armoured/XLPE power cable, working voltage 1100 volts grade direct in ground; to be laid 1 meter below the ground level including excavation and refilling the trench etc.as required, but excluding sand cushioning and protective covering:- Make: KEI/SCI/Havells/Plaza

Armoured cable 50 sq. mm (3.5 core)

Armoured cable 95 sq. mm (3.5 core)

TARUN FIRE SYSTEM