At BJU :- Provision of facilities in TTE Running Rooms at Par with that of running rooms of Guard/Loco pilots.

as per (Schedule - A), Annexure "A-1" except steel Reinforcement.

All Items in conneciton with works under CPWD-DSR 2021 with upto date corrections as per

(Schedule - A), Annexure "A-1" except steel Reinforcement.

S No. Item No Description of Item Unit Qty Rate Amount

4.0 CONCRETE WORK

4.1S CEMENT CONCRETE (CAST IN SITU)

Providing and laying in position cement concrete

4.1 of specified grade excluding the cost of centering

and shuttering - All work up to plinth level :

SONPUR DIVISION-ENGINEERING/EAST CENTRAL RLY

4.1.3 1:2:4 (1 cement : 2 coarse sand (zone-III) derived cum 20 7365.15 147303

from natural sources : 4 graded stone aggregate

20 mm nominal size derived from natural

5.0 REINFORCED CEMENT CONCRETE

5.1S CAST IN SITU

Providing and laying in position specified grade

of reinforced cement concrete, excluding the cost

of centering, shuttering, finishing and

reinforcement - All work up to plinth level :

derived from natural sources: 3 graded stone

aggregate 20 mm nominal size derived from

natural sources)

Reinforced cement concrete work in walls (any

thickness), including attached pilasters,

buttresses, plinth and string courses, fillets,

5.2 columns, pillars, piers, abutments, posts and

struts etc. above plinth level up to floor five level,

excluding cost of centering, shuttering, finishing

and reinforcement :

derived from natural sources : 3 graded stone

aggregate 20 mm nominal size derived from

natural sources)

5.12S PRE-CAST RCC

5.12 Providing, hoisting and fixing above plinth level cum 3 9673.5 29020.5

up to floor five level precast reinforced cement

concrete work in string courses, bands, copings,

bed plates, anchor blocks, plain window sills and

the like, including the cost of required centering,

shuttering but , excluding cost of reinforcement

with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III)

derived from natural sources : 3 graded stone

aggregate 20 mm nominal size derived from

natural sources).

6.0 MASONRY WORK

Brick work with common burnt clay F.P.S. (non

6.1 modular) bricks of class designation 7.5 in

foundation and plinth in:

6.12S HALF BRICK MASONRY

Half brick masonry with common burnt clay F.P.S.

6.12 (non modular) bricks of class designation 7.5 in

foundations and plinth in :

8.0 CLADDING WORK

8.20S STONE WORK DRY CLADDING

8.31 Providing and fixing Ist quality ceramic glazed Sqm 602.5 1063.45 640728.63

wall tiles conforming to IS: 15622 (thickness to

be specified by the manufacturer), of approved

make, in all colours, shades except burgundy,

bottle green, black of any size as approved by

7 Engineer-in-Charge, in skirting, risers of steps

and dados, over 12 mm thick bed of cement

mortar 1:3 (1 cement : 3 coarse sand) and

jointing with grey cement slurry @ 3.3kg per

sqm, including pointing in white cement mixed

with pigment of matching shade complete.

9.0 WOOD AND P.V.C. WORK

Providing and fixing 25 mm thick shutters for cup

SONPUR DIVISION-ENGINEERING/EAST CENTRAL RLY

Providing and fixing ISI marked flush door

shutters conforming to IS : 2202 (Part I)

decorative type, core of block board construction

9.20 with frame of 1st class hard wood and well

matched teak 3 ply veneering with vertical grains

or cross bands and face veneers on both faces of

9.20.2 30 mm thick including ISI marked Stainless Steel Sqm 42 2818.5 118377

butt hinges with necessary screws

9.40S MISCELLANEOUS-WOOD WORK

Providing and fixing chromium plated brass

curtain rod having wall thickness of 1.25mm with

9.46 two chromium plated brass brackets fixed with

C.P. brass screws and PVC sleeves etc., wherever

necessary complete :

Providing and fixing M.S. grills of required pattern

in frames of windows etc. with M.S. flats, square

or round bars etc. including priming coat with

approved steel primer all complete.

9.48.2 Fixed to openings /wooden frames with rawl Kg 800 197.7 158160

plugs screws etc.

Providing and fixing fly proof galvanized M.S.

wire gauge to windows and clerestory windows

9.51 using wire gauge with average width of aperture

1.4 mm in both directions with wire of dia 0.63

mm all complete.

9.72S BRASS FITTINGS

9.84 Providing and fixing aluminium extruded section Each 35 856.3 29970.5

body tubular type universal hydraulic door closer

(having brand logo with ISI, IS : 3564, embossed

12 on the body, door weight upto 36 kg to 80 kg and

door width from 701 mm to 1000 mm), with

double speed adjustment with necessary

accessories and screws etc. complete.

ANODISED ALUMINIUM FITTINGS (ALL FITTINGS

SHALL BE ISI MARKED)

Providing and fixing aluminium sliding door bolts,

ISI marked anodised (anodic coating not less than

9.96 grade AC 10 as per IS : 1868), transparent or

dyed to required colour or shade, with nuts and

screws etc. complete :

Providing and fixing aluminium tower bolts, ISI

marked, anodised (anodic coating not less than

9.97 grade AC 10 as per IS : 1868 ) transparent or

dyed to required colour or shade, with necessary

screws etc. complete :

Providing and fixing aluminium handles, ISI

marked, anodised (anodic coating not less than

9.100 grade AC 10 as per IS : 1868) transparent or

dyed to required colour or shade, with necessary

screws etc. complete :

Providing and fixing aluminium hanging floor

door stopper, ISI marked, anodised (anodic

9.101 coating not less than grade AC 10 as per IS :

1868) transparent or dyed to required colour and

shade, with necessary screws etc. complete.

9.105S GYPSUM BOARD PARTITIONS

SONPUR DIVISION-ENGINEERING/EAST CENTRAL RLY

9.119 Providing and fixing factory made P.V.C. door Metre 180 408.25 73485

frame of size 50x47 mm with awall thickness of 5

mm, made out of extruded 5mm rigid PVC foam

sheet, mitred at corners and joined with 2 Nos of

150 mm long brackets of 15x15 mm M.S. square

tube, the vertical door frame profiles to be

17 reinforced with 19x19 mm M.S. square tube of 19

gauge, EPDM rubber gasket weather seal to be

provided through out the frame. The door frame

to be fixed to the wall using M.S. screws of

65/100 mm size, complete as per manufacturer's

specification and direction of Engineer- in-

Providing and fixing factory made panel PVC door

shutter consisting of frame made out of M.S.

tubes of 19 gauge thickness and size of 19 mm x

19 mm for styles and 15x15 mm for top &

bottom rails. M.S. frame shall have a coat of steel

primers of approved make and manufacture.

M.S. frame covered with 5 mm thick heat

moulded PVC 'C' channel of size 30 mm

thickness, 70 mm width out of which 50 mm shall

be flat and 20 mm shall be tapered in 45 degree

angle on both side forming styles and 5 mm

thick, 95 mm wide PVC sheet out of which 75mm

shall be flat and 20 mm shall be tapered in 45

degree on the inner side to form top and bottom

rail and 115 mm wide PVC sheet out of which 75

9.120 mm shall be flat and 20 mm shall be tapered on

both sides to form lock rail. Top, bottom and lock

rails shall be provided both side of the panel. 10

mm (5 mm x 2 ) thick, 20 mm wide cross PVC

sheet be provided as gap insert for top rail &

bottom rail, paneling of 5 mm thick both side PVC

sheet to be fitted in the M.S. frame welded/

sealed to the styles & rails with 7 mm (5 mm+2

mm) thick x 15 mm wide PVC sheet beading on

inner side, and joined together with solvent

cement adhesive. An additional 5 mm thick PVC

strip of 20 mm width is to be stuck on the interior

side of the 'C' Channel using PVC solvent

adhesive etc. complete as per direction of

Engineer-in-charge, manufacturer's specification

10.0 STEEL WORK

10.2 Structural steel work riveted, bolted or welded in Kg 200 111.95 22390

built up sections, trusses and framed work,

19 including cutting, hoisting, fixing in position and

applying a priming coat of approved steel primer

Steel work in built up tubular (round, square or

rectangular hollow tubes etc.) trusses etc.,

including cutting, hoisting, fixing in position and

applying a priming coat of approved steel primer,

including welding and bolted with special shaped

washers etc. complete.

SONPUR DIVISION-ENGINEERING/EAST CENTRAL RLY

10.28 Providing and fixing stainless steel ( Grade 304) Kg 260 612.25 159185

railing made of Hollow tubes, channels, plates

etc., including welding, grinding, buffing,

polishing and making curvature (wherever

required) and fitting the same with necessary

stainless steel nuts and bolts complete, i/c fixing

the railing with necessary accessories & stainless

steel dash fasteners , stainless steel bolts etc., of

required size, on the top of the floor or the side of

waist slab with suitable arrangement as per

approval of Engineer-in-charge, (for payment

purpose only weight of stainless steel members

shall be considered excluding fixing accessories

such as nuts, bolts, fasteners etc.).

11.0 FLOORING

11.2 Dry brick on edge flooring in required pattern Sqm 132 733.3 96795.6

with bricks of class designation 7.5 on a bed of

22 12 mm mud mortar, including filling joints with

local sand, with common burnt clay non modular

11.16S TILE FLOORING

Chequerred precast cement concrete tiles 22

mm thick in footpath & courtyard, jointed with

neat cement slurry mixed with pigment to match

the shade of tiles, including rubbing and cleaning

etc. complete, on 20 mm thick bed of cement

mortar 1:4 (1 cement: 4 coarse sand).

11.20.2 Medium shade pigment using 50% white cement Sqm 415 1160 481400

50% Grey cement

11.37S CERAMIC GLAZED TILES

11.37 Providing and laying Ceramic glazed floor tiles of Sqm 168 935.6 157180.8

size 300x300 mm (thickness to be specified by

the manufacturer) of 1st quality conforming to IS

: 15622 of approved make in colours such as

White, Ivory, Grey, Fume Red Brown, laid on 20

mm thick cement mortar 1:4 (1 Cement : 4

Coarse sand), Jointing with grey cement slurry @

3.3 kg/sqm including pointing the joints with

white cement and matching pigment etc.,

11.41S VITRIFIED FLOOR TILES

Providing and laying vitrified floor tiles in

different sizes (thickness to be specified by the

manufacturer) with water absorption less than

0.08% and conforming to IS: 15622, of approved

11.41 make, in all colours and shades, laid on 20mm

thick cement mortar 1:4 (1 cement : 4 coarse

sand), jointing with grey cement slurry @ 3.3 kg/

s q m including grouting the joints with white

cement and matching pigments etc., complete.

12.0 ROOFING

12.1S SHEET ROOFING

Providing gola 75x75 mm in cement concrete

1:2:4 (1 cement : 2 coarse sand : 4 stone

12.21 aggregate 10 mm and down gauge), including

finishing with cement mortar 1:3 (1 cement : 3

fine sand) as per standard design :

Providing, fixing and embedding sand cast iron

accessories for rain water pipes in the masonry

12.40 surrounded with 12 mm thick cement mortar of

the same mix, as that of masonry (lead caulking

will be paid for separately):

SONPUR DIVISION-ENGINEERING/EAST CENTRAL RLY

Providing and fixing on wall face unplasticised

Rigid PVC rain water pipes conforming to IS :

12.41 13592 Type A, including jointing with seal ring

conforming to IS : 5382, leaving 10 mm gap for

thermal expansion, (i) Single socketed pipes.

Providing and fixing on wall face unplasticised -

PVC moulded fittings/ accessories for

unplasticised Rigid PVC rain water pipes

conforming to IS : 13592 Type A, including

jointing with seal ring conforming to IS : 5382,

leaving 10 mm gap for thermal expansion.

12.42.5 Bend 87.5 degrees

12.50 Providing and fixing precoated galvanised iron Sqm 140 671.55 94017

profile sheets (size, shape and pitch of

corrugation as approved by Engineer-in-charge)

0.50 mm (+ 0.05 %) total coated thickness with

zinc coating 120 grams per sqm as per IS: 277, in

240 mpa steel grade, 5-7 microns epoxy primer

on both side of the sheet and polyester top coat

15-18 microns. Sheet should have protective

guard film of 25 microns minimum to avoid

scratches during transportation and should be

supplied in single length upto 12 metre or as

desired by Engineer-in-charge. The sheet shall be

fixed using self drilling /self tapping screws of

size (5.5x 55 mm) with EPDM seal, complete upto

any pitch in horizontal/ vertical or curved

surfaces, excluding the cost of purlins, rafters

and trusses and including cutting to size and

shape wherever required.

13.0 FINISHING

13.4S CEMENT PLASTER (IN COARSE SAND)

13.4 12 mm cement plaster of mix :

CEMENT PLASTER WITH A FLOATING COAT OF

12 mm cement plaster finished with a floating

coat of neat cement of mix :

13.25 Extra for plastering:

13.26 Providing and applying plaster of paris putty of 2 Sqm 3400 214.3 728620

33 mm thickness over plastered surface to prepare

the surface even and smooth complete.

Distempering with oil bound washable distemper

13.41 of approved brand and manufacture to give an

13.41.1 New work (two or more coats) over and including Sqm 3000 162.55 487650

water thinnable priming coat with cement primer

13.44S EXTERIOR FINISHING

Finishing walls with Acrylic Smooth exterior paint

of required shade :

35 ltr/10 sqm over and including priming coat of

exterior primer applied @ 2.20 kg/10 sqm)

Lettering with black Japan paint of approved letter

brand and manufacture per cm

Applying priming coats with primer of approved

13.85 brand and manufacture, having low VOC (Volatile

Organic Compound ) content.

SONPUR DIVISION-ENGINEERING/EAST CENTRAL RLY

13.91 Removing dry or oil bound distemper, water Sqm 2500 20.85 52125

proofing cement paint and the like by scrapping,

37 sand papering and preparing the surface smooth

including necessary repairs to scratches etc.

Painting with synthetic enamel paint of approved

13.99 brand and manufacture of required colour to give

an even shade :

Finishing walls with water proofing cement paint

of required shade :

13.109.1 Old work (one or more coats applied @ 2.20 Sqm 600 94.15 56490

kg/10 sqm) over priming coat of primer applied

@ 0.80 litrs/10 sqm complete including cost of

15.0 DISMANTLING AND DEMOLISHING

15.3 Demolishing R.C.C. work manually/ by cum 1 2928.1 2928.1

mechanical means including stacking of steel

40 bars and disposal of unserviceable material

within 50 metres lead as per direction of

Engineer - in- charge.

Dismantling doors, windows and clerestory

windows (steel or wood) shutter including

chowkhats, architrave, holdfasts etc. complete

and stacking within 50 metres lead :

Dismantling tile work in floors and roofs laid in

15.23 cement mortar including stacking material within

50 metres lead.

15.56 Dismantling old plaster or skirting raking out Sqm 3000 45.05 135150

joints and cleaning the surface for plaster

including disposal of rubbish to the dumping

ground within 50 metres lead.

17.0 SANITARY INSTALLATIONS

Providing and fixing water closet squatting pan

(Indian type W.C. pan ) with 100 mm sand cast

Iron P or S trap, 10 litre low level white P.V.C.

flushing cistern, including flush pipe, with

manually controlled device (handle lever)

conforming to IS : 7231, with all fittings and

fixtures complete, including cutting and making

good the walls and floors wherever required:

17.1.1 White Vitreous china Orissa pattern W.C. pan of Each 8 5781.35 46250.8

size 580x440 mm with integral type foot rests

Providing and fixing white vitreous china

pedestal type water closet (European type W.C.

pan) with seat and lid, 10 litre low level white

P.V.C. flushing cistern, including flush pipe, with

manually controlled device (handle lever),

conforming to IS : 7231, with all fittings and

fixtures complete, including cutting and making

good the walls and floors wherever required :

17.2.1 W.C. pan with ISI marked white solid plastic seat Each 4 5540.55 22162.2

Providing and fixing white vitreous china flat

back or wall corner type lipped front urinal basin

of 430x260x350 mm and 340x410x265 mm sizes

respectively with automatic flushing cistern with

17.4 standard flush pipe and C.P. brass spreaders with

brass unions and G.I clamps complete, including

painting of fittings and brackets, cutting and

making good the walls and floors wherever

17.4.1 One urinal basin with 5 litre white P.V.C. Each 10 5268.85 52688.5

automatic flushing cistern

SONPUR DIVISION-ENGINEERING/EAST CENTRAL RLY

17.7A Providing and fixing wash basin with C.I. Each 10 3459.05 34590.5

brackets, 15 mm dia CP Brass single hole basin

mixer of approved quality and make, including

painting of fittings and brackets, cutting and

making good the walls wherever required:- (a)

White Vitreous China Wash basin size 550x400

mm with a 15 mm CP Brass single hole basin

Providing and fixing Stainless Steel A ISI 304

(18/8) kitchen sink as per IS:13983 with C.I.

brackets and stainless steel plug 40 mm,

including painting of fittings and brackets,

cutting and making good the walls wherever

17.10.2 Kitchen sink without drain board

17.16A Providing and fixing 8 mm dia C.P. / S.S. Jet with Each 4 299.35 1197.4

flexible tube upto 1 metre long with S.S.

triangular plate to Eureopean type W.C. of quality

and make as approved by Engineer - in - charge.

Providing and fixing P.V.C. low level flushing

cistern with manually controlled device (handle

lever) conforming to IS : 7231, with all fittings

and fixtures complete.

Providing and fixing P.V.C. waste pipe for sink or

17.28 wash basin including P.V.C. waste fittings

17.28.1 Semi rigid pipe

17.31 Providing and fixing 600x450 mm beveled edge Each 10 1411.15 14111.5

mirror of superior glass (of approved quality)

52 complete with 6 mm thick hard board ground

fixed to wooden cleats with C.P. brass screws and

washers complete.

17.33 Providing and fixing 600x120x5 mm glass shelf Each 20 942.15 18843

with edges round off, supported on anodised

53 aluminium angle frame with C.P. brass brackets

and guard rail complete fixed with 40 mm long

screws, rawl plugs etc., complete.

Providing and fixing PTMT towel rail complete

with brackets fixed to wooden cleats with CP

brass screws with concealed fittings arrangement

of approved quality and colour.

17.73.2 600 mm long towel rail with total length of 645 Each 20 600.35 12007

54 mm, width 78 mm and effective height of 88

mm, weighing not less than 190 gms.

18.0 WATER SUPPLY

18.7S C.P.V.C. PIPES

Providing and fixing G.I. pipes complete with G.I.

18.12 fittings including trenching and refilling etc.-

18.15S BRASS FITTINGS

Providing and fixing brass stop cock of approved

Providing and fixing ball valve (brass) of

18.18 approved quality, High or low pressure, with

plastic floats complete :

SONPUR DIVISION-ENGINEERING/EAST CENTRAL RLY

Providing and fixing uplasticised PVC connection

pipe with brass unions :

18.21.2 45 cm length

Providing and fixing C.P. brass shower rose with

15 or 20 mm inlet :

18.31S C.I. SLUICE VALVES/ FIRE HYDRANTS & FIXTURES

Providing and fixing G.I. Union in G.I. pipe

18.46 including cutting and threading the pipe and

making long screws etc. complete (New work) :

18.48 Providing and placing on terrace (at all floor Litre 11000 9.7 106700

levels) polyethylene water storage tank, IS :

12701 marked, with cover and suitable locking

arrangement and making necessary holes for

inlet, outlet and overflow pipes but without

fittings and the base support for tank.

18.49S C.P. BRASS FITTINGS

Providing and fixing C.P. brass angle valve for

18.53 basin mixer and geyser points of approved

quality conforming to IS:8931

18.54S PTMT FITTINGS

Providing and fixing PTMT bib cock of approved

quality and colour.

18.54.2 15 mm nominal bore, 122mm long, weighing not Each 60 143.3 8598

less than 99 gms

18.59S AIR VALVE & WATER METER (BULK TYPE)

Providing and fixing PTMT extension nipple for

18.75 water tank pipe, fittings of approved quality and

18.75.2 20 mm nominal bore, weighing not less than 40 Each 22 76.5 1683

21.0 ALUMINIUM WORK

Providing and fixing aluminium work for doors,

windows, ventilators and partitions with extruded

built up standard tubular sections/ appropriate Z

sections and other sections of approved make

conforming to IS: 733 and IS: 1285, fixing with

dash fasteners of required dia and size, including

necessary filling up the gaps at junctions, i.e. at

top, bottom and sides with required EPDM

21.1 rubber/ neoprene gasket etc. Aluminium sections

shall be smooth, rust free, straight, mitred and

jointed mechanically wherever required including

cleat angle, Aluminium snap beading for glazing /

paneling, C.P. brass / stainless steel screws, all

complete as per architectural drawings and the

directions of Engineer-in-charge. (Glazing,

paneling and dash fasteners to be paid for

21.1.1 For fixed portion

21.1.1.1 Anodised aluminium (anodised transparent or Kg 10 433.95 4339.5

72 dyed to required shade according to IS: 1868,

Minimum anodic coating of grade AC 15)

SONPUR DIVISION-ENGINEERING/EAST CENTRAL RLY

For shutters of doors, windows & ventilators

including providing and fixing hinges/ pivots and

making provision for fixing of fittings wherever

required including the cost of EPDM rubber /

neoprene gasket required (Fittings shall be paid

for separately)

21.1.2.2 Powder coated aluminium (minimum thickness of Kg 10 564.8 5648

powder coating 50 micron)

Providing and fixing glazing in aluminium door,

window, ventilator shutters and partitions etc.

with EPDM rubber / neoprene gasket etc.

21.3 complete as per the architectural drawings and

the directions of engineer-in-charge . (Cost of

aluminium snap beading shall be paid in basic

21.3.2 With float glass panes of 5 mm thickness (weight Sqm 12 1325.55 15906.6

not less than 12.50 kg/sqm)

22.0 WATER PROOFING

22.6 Providing and laying water proofing treatment on Sqm 1060 585.55 620683

roofs of slabs by applying cement slurry mixed

with water proofing cement compound consisting

of applying: (a) after surface preparation, first

layer of slurry of cement @ 0.488 kg/sqm mixed

with water proofing cement compound @ 0.253

kg/sqm. (b) laying second layer of Fibre glass

cloth when the first layer is still green. Overlaps

of joints of fibre cloth should not be less than 10

cm. (c) third layer of 1.5 mm thickness consisting

75 of slurry of cement @ 1.289 kg/sqm mixed with

water proofing cement compound @ 0.670

kg/sqm and coarse sand @ 1.289 kg/sqm. This

will be allowed to air cure for 4 hours followed by

water curing for 48 hours. The entire treatment

will be taken upto 30 cm on parapet wall and

tucked into groove in parapet all around. (d)

fourth and final layer of brick tiling with cement

mortar (which will be paid for separately. For the

purpose of measurement the entire treated

surface will be measured.

22.14 Grading roof for water proofing treatment with

22.14.1 Cement concrete 1:2:4 (1 cement : 2 coarse sand cum 53 7510.75 398069.75

: 4 graded stone aggregate 20mm nominal size)

Schedule Schedule A 3-Items of steel reinforcement udner DSR-2021.

Item- 01 Items of steel reinforcement udner DSR-2021.

S No. Item No Description of Item Unit Qty Rate Amount

5.0 REINFORCED CEMENT CONCRETE

5.22S STEEL REINFORCEMENT

Steel reinforcement for R.C.C. work including

straightening, cutting, bending, placing in

position and binding all complete upto plinth

5.22.6 Thermo-Mechanically Treated bars of grade Fe- Kg 478 89.65 42852.7