CERTAIN SANCTION WORK SUCH AS SPECIAL REPAIR AND REVENUE WORK UNDER AGE R/R-II AT YOL CANTT

Amount

SCHEDULE 'A' PART-I:- Demolition Brickwork or stone/boulder masonry, laid dry all as specified.

Excavating over areas, n exc 1.5 m deep and getting out getting out in any type of soil, all as specified.

Demolition of cement concrete (unreinforced) in ground floors and paving, not exceeding 15cm thickness (below or above ground level), un-reinforced, complete all as specified.

Demolition of stones or brick masonry, built in cement mortar including all quoins, arches etc., but excluding ashlar facing, dressed stone work etc.complete,all as specified.

Dismantling wall and ceiling boards (fiber, pulp, insulation etc) or insulation boards/ slabs/ blankets, any thickness including cover fillets in ceiling, all as specified.

Dismantling of wooden fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section in unframed work, all as specified.

Excavation in trenches not exc 1.5 metres wide and n.exc 1.5 metres deep and getting out in any type of soil, all as specified.

Surface excavation not exceeding 30 cms deep and averaging 15cms deep and getting out in any type of soil, complete all as specified.

Excavating in post holes (or similar holes) each n exc 0.5 cu. M, getting out in any type of soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, all as specified.

Returning filling in including spreading, levelling, watering and well ramming in layers not exc.25cm thick each layer of soil all as specified.

Removing excavated material exc. 50mtrs and not exc. 250mtrs and depositing where directed at a level not exc. 1.5m above the starting point complete all as specified.

Removing excavated material exc. 250mtrs and not exc. 500mtrs and depositing where directed at a level not exc. 1.5m above the starting point complete all as specified.

Hand packing with Broken stone Broken or boulders (any thickness) at back of walls near weep holes etc. and raising (or lowering) to the required level complete all as specified.

PVC (SWR) pipes single socketed, in any length with rubber ring joints, as in weep holes of bore 75mm complete, all as specified.

Plain cement concrete M-15 nominal mix, type B-1 using 20 mm graded mechanically crushed stone aggregate as in surface channel and drains all as specified.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc., complete all as specified.

Steel window 1.25mm thick box type (Primer coated) ERW hollow P section of size 85mm x 35mm double rebated comprises gauged, glazed skelton shutter ERW Sec 50mm x 20mm and 1mm thick with two openable leaf consiting two Nos sash bar of T-Section 20mm x 3mm complete welded to frame with one vertical mullion of ERW box type T-section of size 30mm x 25mm and 1.25mm thick including cutting holes and making good dismantled portion in PCC M-15, type B-0 (04 No's for each window, steel duly painted with one shop coat of zinc chromate primer on prepared surfaces) and finishing the surfaces to match with existing including following fitting welded to frame shutter:-(i) Hold fast, 150mm long of 12mm x 3mm made to shape -04 Nos per window.(ii) Handle of Z section 20mm x 25mm, 100mm long -1 No per leaf.(iii) MS tower bolt 150mm long - 2 No per leaf(iv) Z section 20mm x25mm, 100 long stopper - 1 No per leaf.(v) Cleat 65mm long of hollow square 15mm x 20mm x 63mm welded to hinge -1 No per leaf.(vi) Mild steel pintle hinge of size 75mm x 12mm - 2 Nos per leaf.(vii) Flat iron fillets of size 20X3 mm for fixing wire gauge.(viii) Fabrication & fixing arrangement as per drg No. CEPZ/ TD 06/07.Make : As per Appendix 'C'.Note:-(i) Above referred drawing has not been made part of tender. The same can be seen in the office of GE during working hours on any working day.

Plain cement concrete M-10, nominal mix, C-2, using 40mm graded mechanically crushed stone aggregate as in foundation, filling and mass concrete, complete all as specified.

Plain cement concrete M-7.5, nominal mix, D-2, using 40mm graded mechanically crushed stone aggregate as in foundation, filling and mass concrete, complete all as specified.

Taking down chowkats or frames including shutters (without taking off shutters from the frame) exc. 1.5 Sqm but not exc. 4 Sqm each and removing from site, all as specified.

Taking down chowkats or frames including shutters (without taking off shutters from the frame) not exc. 1.5 Sqm each and removing from site, all as specified.

Brick work with fly ash bricks, old size bricks having crushing strength not less than 75 Kg/Sqcm, straight or curved on plan exceeding 6m mean radius built in cement mortar 1:6 (1 cement : 6 coarse sand), complete all as specified.

Brick work fly ash with old size bricks having crushing strength not less than 75 Kg/Sqcm, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 (1 cement : 4 coarse sand), all as specified.

4mm thick non asbestos fiber cement building boards (Decorative E Board) as in ceiling fixed to galvanised iron frame work ( Size of grid 605mmx605mm) comprising of galvanised iron perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/ intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with hangers 6 mm dia galvanised (length as per site requirement) adjusting level fixed to roof by means of ceiling cleats made out of galvanised iron flat 40 mm X 3 mm size, 60 mm long and expansion hold fasteners 12.5 mm dia, 40 mm long with and including ceiling section (not exc 1.2 metre length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre, including necessary scaffolding all as specified and directed.

Cutting holes in brick walls in cement mortar or cement lime mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required, Depth of embedded portion of holdfasts or lugs measured from the face of the jamb into the wall exc. half brick wall but not exc one brick complete all as specified.

Rendering cement plaster 15mm thick in cement mortar 1:4 (1 cement : 4 coarse sand) on fair faces of brick wall or concrete surfaces, surface finished even and smooth without using extra cement with WPC , all as specified. Note :- water proofing compound shall be measured and paid separately

Rendering plaster 15mm thick in cement mortar 1:6 (1 cement :6 coarse sand) on other than fair faces of brick wall or stone wall surfaces, surface finished even and smooth without using extra cement, all as specified.

Preparation of newly plastered wall surfaces and applying two coats of oil bound distemper over a coat of primer 2mm thick wall care putty to achieve smooth surface complete, all as specified and as directed.

Complete removal of existing treatment of old surfaces of wall and applying two coats of oil bound distemper over 2mm thick wall care putty to achieve smooth surface complete, all as specified and as directed.

Complete removal of existing treatment of old surfaces of wall and applying two coat of exterior emulsion (acrylic emulsion paint) over 2mm thick wall care putty to achieve smooth surface complete, all as specified and as directed.

Applying two coats of synthetic enamel paint on old steel or steel based surfaces of any description, exceeding 10cm width or girth including preparation of surfaces, all as specified.

Dismantling floor, hearth or wall tiling including cement mortar bedding (But not backing), removing and rubbish of the premisses, complete all as specified.

Preparation of plastered surface of wall and applying two coat of exterior emulsion (acrylic emulsion paint), over a coat of primer complete all as specified and directed.

Three coats of white wash on newly plastered or un plastered, previously undecorated wall surfaces including preparation of surfaces complete, all as specified.

Supply only intergal water proofing compound, complete all as specified.

Reinforced cement concrete (design mix) M-25 ( using 20mm graded crushed stone aggregate as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete, all as specified.

Reinforced cement concrete (design mix) M-25 ( using 20mm graded crushed stone aggregate) as in beams, cantilevers, bressummers, lintels over 1.5m span, all as specified.

Reinforced cement concrete (design mix) M-25 ( using 20mm graded crushed stone aggregate) Walls, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilasters and buttresses®s, all as specified.

Precast cement M-15 , type B-1, using 20mm graded crushed stone aggregate as in landings, cover slab (for manholes etc.), chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces including chamfers, weatherings, throating etc. and setting in cement mortar 1:4 complete with joints to match, complete all as specified.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams,sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter, for roughly finished flat surfaces of concrete, all as specified.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. For roughly finished flat surfaces of concrete, all as specified.

Formwork to Formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batter For roughly finished flat surfaces of concrete, all as specified.

TMT bars 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips , all as specified.

TMT bars 6 to 8mm dia cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips as in stirrups, spacers and binders, all as specified.

Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as complete, all as specified and directed.

Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as complete, all as specified and directed.

Corrugated galvanised iron mild steel sheets 0.63mm thick, grade ‘O’, with 120 grams per square metre zinc coating fixed with 'J' or 'L' hook as in roof covering with two corrugation side lap. (Horizontal distance of side lap shall not be less than 145mm and depth of corrugation shall be 12.5mm), all as specified.

Plain mild steel wire 4mm dia, galvanised class 3, in fencing including straining and fixing to wood, concrete or steel posts and/or to straining bolts, including securing with and provision of galvanised iron tying wire, galvanised iron staples or steel pins, etc. as directed (each line of wire to be measured) complete, all as specified and directed.

Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured), all as specified.

Rolled mild steel sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates conforming to grade Fe-410-0 Gde E-250, all as specified.

Rolled mild steel work as in Joist, channel, angle, or tee sections,fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) conforming to Fe-410 W (Gde E-250), Quality A, complete all as specified.

Mild Steel framed work as Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment complete, conforming to Fe 290 Gde E-165 , all as specified.

MS angle iron work inposts and struts in fencing including cutting tops to shape as directed, drilling holes,notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 , all as specified.

Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 5cm long but not exc 10 cm long, diameter of neck 11 to 15mm, complete all as speciied.

Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 22.5cm long but not exc 30cm long, diameter of neck 11 to 15mm, complete all as speciied.

Mild steel framed work such as grills, gratings, etc with ends of bars shouldered and/ or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed ballusters walk ways; railings; framework of water tanks and similar work conforming to Fe.290. Gde-E-165, all as specified.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire, complete all as specified.

Supply Only Chain link MS galvanisd fencing, any size or type, complete all as specified.

Mild steel work as in bolt hooks (stay) hook and pintle hinges, bands, straps, hold fasts, clamps, wall ties, cleats, fanhooks etc. or similar small articles conforming to grade Fe-290 grade E-165, all as specified.

Granite (of any type) 16-18mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete as in floors laid over and including 15mm thick screed bed in cement mortar (1:4), all as specified.

Machine cut kota stone slab flooring 18-20 mm thick of size not less than 550 mm X 550 mm as per sample kept in GE’s office, laid and jointed with grey cement slurry mixed with pigment to match the shade of slab, as in floor etc, laid over and including 15mm screed layer in cement mortar 1:4 (1 cement : 4 coarse sand), cutting, rubbing, grinding and polishing to achieve mirror finish complete, all as specified.

Marble work 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, windowcills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade makrana white type laid over and including 15mm thick screedbed in cement mortar (1:4), all as specified.

Vitreous China wash down water closet (pedestal pattern), white including traps, connection to drain or outgoing pipe, PVC 32mm dia flushing pipe, anti-syphonage pipe complete including fittings, PVC white seat cover and chromium plated jet including PVC valveless, syphonic action type flushing cistern 10 litres capacity low level with inlet, ball valve , float and handle with brackets , fixed complete , all as specified.

Angular valve, cast copper alloy, chromium plated fancy type, screwed down, high pressure with crutch or butterfly handle, screwed both ends for 15mm bore iron pipe or for unions and fixed complete, all as specified.

Wash basins, Vitreous China (Flat back type) size 550mmx400mm, crystal white with and including cutting for and pinning on ends of brackets, 450 mm long PVC connections 15mm size with PTMT coupling nuts at both ends, trap, grating and Union for discharge pipe, waste, chain and plug and porcelain stopper, waste pipe of polythylene of low or high density or PVC of 32mm dia including Pillar taps, 15mm bore cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot' or ‘Cold' with long screwed shanks and fly-nuts, 32mm dia waste fittings, brass chromium plated with long screwed shanks and fly nuts, flange and bedded in red lead cement and other end fixed, screwed for iron pipe and fixed in repairs, complete all as specified.

PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors or fixed to wall of bore 110mm complete, all as specified.

PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors or fixed to wall of bore 75mm complete, all as specified.

PVC (SWR) floor trap/nahani, plain with grating including jointing with solvent cement, dia of outlet 75mm, all as specified.

PVC (SWR) gully trap 125/110 mm,setting and jointing with solvent cement, complete all as specified

PVC (SWR) bends any radius, 100mm bore with ovel access door, all as specified.

PVC (SWR) bends any radius, 75mm bore with ovel access door, all as specified.

PVC (SWR) junction single, (Single T) equal or unequal, 110mm bore, provided with oval access door all as specified.

PVC (SWR) junction single, (Single T) equal or unequal, 75mm bore, provided with oval access door all as specified.

Rotational moulded polyethylene water storage tank 250 Ltrs capacity (Cylinderical vertical with closed top) hoisted and fixed in position with PVC float ball valve 20mm dia with polythene float and fly nut, tank nipples with check nuts and washers complete and making connections with existing water supply line complete, all as specified.

Stop valve, cast copper alloy, chromium plated, screwed down, high pressure with crutch or butterfly handle, screwed both ends for 20mm bore iron pipe or for unions and fixed complete, all as specified.

Vitreous Chinaware squatting pan, ‘Orrisa pattern’ size 580 mm x 440 mm, crystal white, with cast iron ‘P’ or ‘S’ trap, front or back inlet, integral foot rest with provision of plain cement concrete M-15, type B-I using 20 mm graded crushed stone aggregate complete all as specified, incl making connections to trap and to flush pipe, etc . all as specified.

Vitreous China Urinal, Half stall type,white ( white (minimum) with grating and union for discharge pipe, complete including providing and fixing plugs, beding urinal against wall in cement mortar 1:2 securing urinal plugs with and including 60mm long brass screws, pointing around urinal back in cement, including 32mm bore PVC waste pipe, complete all as specified.

PVC valve less, crystal white, syphonic action type flushing cistern 10 litre capacity, superior quality, plunger type, low level, with inlet, ball valve, float and handle, 32 mm dia PVC long bend flush pipe 90cm long and 15 mm dia 600 mm long PVC connection with CP brass coupling nuts and PVC washers at both ends fixed, in repairs, all as specified.

Hard core of broken stone or boulders of gauge not exc. 63mm deposited, spread and levelled in layers not exc. 15cm thick, watered and rammed to a true surface, all as specified.

Sand filling under floors or in foundations including watering and consolidations, all as specified.

75mm thick Plain cement concrete M-7.5, nominal mix, D-2, using 40mm graded mechanically crushed stone aggregate as in sub base complete all as specified.

40mm thick Plain cement concrete M-15 nominal mix, B-2, using 40mm graded mechanically crushed stone aggregate as in sub base complete all as specified.

Plain cement concrete M-15, nominal mix, type B-0, using 12.5mm graded mechanically crushed stone aggregate as in floors, 25mm thick, surface finished even and fair to receive top surface, all as specified.

Vitrified ceramic tiles Dark shade/Double charged/ ultracharged, 10mm thick (Square/ rectangular) area of each tile exc. 0.18 Sqm but not exc. 0.36Sqm, in floors and the like, set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 15mm thick screed bedding layer in cement mortar 1:6(1 cement : 6 coarse sand) complete, all as specified.

Vitrified ceramic tiles Dark shade/Double charged/ ultracharged, 10mm thick (Square/ rectangular) area of each tile exc. 0.18 Sqm but not exc. 0.36Sqm, in vertical surfaces such as jointed in neat cement slurry and pointed with white cement to match and including 10mm thick plastering in cement mortar 1:4 (1 cement : 4 coarse sand) complete, all as specified.

Mat finish (non skid), Premium class I grade, joint free coloured, ceramic tiles, 7 to 8mm thick (Square/ rectangular) area of each tile exc. 0.09Sqm but not exc. 0.18 Sqm, in floors and the like, set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 15mm thick screed bedding layer in cement mortar 1:6(1 cement : 6 coarse sand) complete, all as specified.

Joint free premium class I grade,coloured, ceramic tiles, 7 to 8mm thick (Square/ rectangular) area of each tile exc. 0.09Sqm but not exc. 0.18 Sqm, in vertical surfaces such as skirting dado, jointed in neat cement slurry and pointed with white cement to match and including 10mm thick plastering in cement mortar 1:4 (1 cement : 4 coarse sand) complete, all as specified.

Glazed coloured tiles of size 450x300x7mm thick as in vertical surfaces such as jointed in neat cement slurry and pointed with coloured cement to match and including 10mm thick plastering in cement mortar 1:4 (1 cement : 4 coarse sand) complete, all as specified.

Plain cement concrete M-10, nominal mix, type C-1, using 20mm graded mechanically crushed stone aggregate, 75mm thick as in plinth protection etc., surface finished even and smooth without using extra cement and laid to a slope of 1 in 24 in alternate panels n.exc. 1.20 Sqm each, 12mm wide and 5 cms deep joints shall be formed between the bays and shall be filled with mastic filling comprising a mixture of one part of heated blown bitumen VG-10 and two parts of heated coarse sand (by volume), all as specified. Note:- The unit rate include for use of form work (straight or curved).

30mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides and lapping one side with 2nd class hard wood beads, all as specified.

0.9mmthick Decorative laminate type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instructionsall as specified.

Aluminium alloy, anodised,sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, length of bolt 250mm with lipping frame to match , all as specified.

Extruded aluminium alloy handles, fabricated type, anodised, of size 100mm, all as specified.

Extruded aluminium alloy handles, fabricated type, anodised, of size 150mm, all as specified.

Aluminium anodised, (ISI marked), barrel tower bolts of extruded section, length of bolt 125mm , fixed ,all as specified.

Aluminium anodised, (ISI marked), barrel tower bolts of extruded section, length of bolt 75mm , fixed ,all as specified.

S & F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised Width of flaps (when open) in 40mm, all as specified.

Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, nodised and fixed, type B-21 100mm long, all as specified.

Hasp and staple, safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws, staple in 100mm long, all as specified.

Applying two coats of synthetic enamel paint over a coat of pink primer on new wood or wood based surfaces of any description, exc. 10cm width or girth complete ,all as specified.

Applying two coats of synthetic enamel paint over a coat of red oxide on new steel or steel based surfaces of any description, exceeding 10cm width or girth including preparation of surfaces, all as specified.

Mild steel galvanised wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18 mm fixed with tinned tacks or wire staples or wooden beads, all as specified.

Sheet glass 3mm thick ordinary quality and glazing with oil putty/wooden beads in squares, not exc. 0.5sqm in each pane, complete all as specified.

Solid PVC Wall Lining consisting of 5mm thick single side prelam PVC sheet inclusive of solvent cement and fixing at site including GI frame work for seamless ceilling comprising of GI permeter channel 0.55mm thick with two unequal flanges of 20mm and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/intermediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section of 0.55mm thickness having kurled web of 50mm and flange of 26mm each lips of 10.5mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457mm centre to centre complete size of grid 605x605mm all as specified and directed.

Plain cement concrete M-10 type C-2 nominal mix using 40mm graded aggregate as in concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for internal dia of pipe 150 mm, all as specified.

Salt glazed stone ware gade 'A' drain pipes, laid in trenches and jointed complete, internal dia of pipe 150mm, all as specified.

2nd class hard wood (Sal/Hollock) plain, solid, straight chowkats and frames, wrought, framed, rebated on solid, rounded or chamfered, put together with glue, pinned at joints with one or more rebates, all as specified.

Applying two coats of cement base paint on newly plastered or previously undecorated wall surfaces including preparation of surface, tint and shade as approved by Engr-in-Charge.

Sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete, including PVC waste pipe 32mm dia all as specified.

Bib taps, 15mm bore, cast copper alloy fancy type with crutch or butterfly handle, screwed down, chromium plated screwed for iron pipe or for brass ferrule and fixed , all as specified.

Brass Chromium Plated, Tubular towel rail, 20mm dia, D type, 60cm long between flanges, with brackets, fixed with chromium plated screws, fixed , complete all as specified.

Factory made solid PVC PUF Door Frame of size 90mm x 55mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification and all as shown on drg No CEPZ/TD-378/11 sheet1/1. Note:-Above mentioned drawing has not been made part of tender. The same can be seen in the office of GE during working hours on any working day. Make : HR Enterprises( Pathankot)/ Techno Fab India (Ambala)/ Durasom (Kolkatta)

Factory made solid PVC Door Frame of size 50mm x 47mm made out of 5mm single side prelam PVC sheet and edges shall be painted to match with prelam sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing on page No 160 of MES SSR 2010 Part-II

Factory made HDF PVC prelaminated moulded door shutter 35 mm thick (Stile) with 2, 4, or 6 raised panel design with fibre raised 4mm thick, 3D wood grain, moulded PVC sheet polyurethane painted on the front face and 4 mm plain coloured PVC sheet on back face. PUF filled door shutters with PUF insulation of minimim density 40 Kg/sqm, suppling and fixing in frame at site as per specification and all as shown on drg No CEPZ/TD-378/11 sheet1/1. Note:-Above mentioned drawing has not been made part of tender. The same can be seen in the office of GE during working hours on any working day.Make : HR Enterprises (Pathankot)/Techno Fab India (Ambala)/Durasom (Kolkatta)

Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of 5 mm thick plain coloured PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site, Sheet No 1/1) specified and directed.

Factory made fully glazed PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; completespecified and directed. Note:- Glass shall be measured and paid separately.

Taking down cement plaster on brick or stone surfaces and tiles with bedding etc. including raking out joints, hacking for key, scrubbing down with water etc. complete all as specified.

Anodised aluminium snap grid frame work (Size of grid 605mmx605mm) for false ceiling all as specified in clause 10.38.1 on serial Page No 216 of SSR Part-I-2009, including necessary scaffolding all as specified and directed.

4mm thick non asbestos fiber cement building boards as in ceiling fixed or laid/ inserted to timber/GI / aluminium framework fixed with nails, including preparation of surface and applying three coats of white wash complete,all as specified.

PVC connection 15mm size with PTMT nuts at boths end 450mm long and fixed, all as specified.

Mild steel galvanized iron water tubing 20mm bore with screwed & socket joints, medium grade, in short lengths, with and including all fittings, such as sockets, bends, elbows, unions, tees, diminishing pieces etc. Fixed to wall or ceiling or laid in floor complete, all as specified and directed.

Mild steel galvanized iron water tubing 15mm bore with screwed & socket joints, medium grade, in short lengths, with and including all fittings, such as sockets, bends, elbows, unions, tees, diminishing pieces etc. Fixed to wall or ceiling or laid in floor complete, all as specified and directed.

Supply fabricate & fix in position aluminum powder coated (Minimum thickness of powder coating 50 micron of approved colour) three track window (two shutters glazed & one shutters wire gauge) with frame, glazed with 4mm thick tinted glass and, wire gauge with stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm ,including rubber bead joining cleat for fixing in position, concealed type lock for all three shutter, PVC roller etc all as specified below, complete all as specified and directed. (a) Frame (top & side) section shall of size 92.00 x 31.75 x 1.50mm (section No 20831) (b) Frame (bottom) section shall of size 92.00 x 31.75 x 1.50mm (section No 20832) (c) Top & side Members of shutter section shall be of size 18.00 x 40.00 x 1.55mm (Section No 20738) (d) Shutter Interlock sectioni shall be of size 18.00 x 40.00x1.45mm (section No 20737) (e) Bottom Members of shutter section shall be of size 18.00 x 40.00 x 1.55mm (Section No 20736) Note:-Section No given above are of make jindal, contractor may use similar section of other make mention in Appx 'C'.

Supply fabricate & fix in position anodised aluminium powder coated (minimum thickness of powder coating 50 micron of approved colour) door shutter with frame, partly glazed with 5mm thick tinted glass and partly panelled with 9mm thick prelaminated particle board with both side decorative laminated including rubber bead joining cleat for fixing in position, aluminium door handle 150mm size, aluminium barrel tower bolt 200mm size , including double door action floor spring of 1.25mm thickaluminium alloy sheet foundation box, main body with stainless steel cover,etc all as specified below complete all as specified and directed. (a) Frame ( top & side) section shall of size 101.60 x 44.75 x 2.4mm (Section No 14021) (b) Vertical Members of shutter section shall be of size 85.00x44.45x2.00mm (section No 19560) (c) Top Members of shutter Section shall be of size 83.50 x 44.45 x 2.00mm (section No 19581) (d) Lock rail (Middle member) of shutter section shall be of size 150.00x44.45x3.00mm (section No 19596) (e) Bottom Members of shutter section shall be of size 150.00x44.45x3.10mm (section No 19584) (f) Glazing clip for securing glass of shutters shall be of 0.80mm thick (section No 19370) Note:- (i) Section No given above are of make jindal, Contractor may use similar section of other make mention in Appx 'C'

S & F aluminium (powder coated 50 micron with approved colour) ventilator, partially glazed and partially louvers, outer frame & mullion fabricated with aluminium section of size 82.50mmx 38.00mmx 1.50mm thick (Cat No 20036), half portion glazed with 4mm thick frosted glass including rubber beading, & glazing clip, half portion louvers of 80mm wide & 4mm thick frosted glass including aluminium louver patti incluidng S.S wire gauge of fixing of 0.36mm dia and 1.40 width of aperture with 25x3mm think aluminium strip with screw to upper half portion of ventilator all fitting & fixture and fixed in position including taking down old ventilator complete Note:-(i)Section No given above are of Make-Jindal , Contractor may use similar section of other make mention in Appx 'C'

Supply , fabricate and fixing aluminium anodised (powder coated 50 micron with approved colour) partition wall , partly glazed with 5mm thick tined glass and partly panelled with 9mm thick pre- laminated particle board with both side decorative laminated including rubber bead joining cleat for fixing in position etc comprising of. (a) Outer member top & vertical fabricated with aluminium section of size 101.6x44.45xx2.5mm thick (Cat No 20102),. (b) Middle member top & vertical of size 101.60X44.45X2.5mm(Cat No 20057). (c) Glazing clip for securing glass / panel of 0.80mm thick (section No. 19370 Note:-(i)Section No given above are of Make-Jindal, Contractor may use similar section of other make mention in Appx 'C'

PCC M-15, nominal mix, B-1 using 20mm graded mechanically crushed stone aggregate as, in lintels up to 1.5 metre clear span cuts, steps seismic and other similar bends, coping, bands plates for serving hold fasts etc. and the like including weathering slighting rounded or chamfered angles and throating complete all as specified. Note:- (i) The unit rate include for use of form work (straight or curved). (ii) Reinforcement if any shall be measured and paid separately.

Providing M-15, nominal mix, type B-0, using 12.5mm graded mechanically crushed stone aggregate as in 50mm thick precast cement louvres and jallies, (measured solid), including all mouldings set in cement mortar 1:4 complete all as specified

Constraction of Septic tank for 10 users all as shown in Drg No. CEPZ/C-TD/013/13 (Sheet 1/5 to5/5), complete all as specified.

Constraction of Soakage well 1.8 metre dia, 3.00 metre deep all as shown in Drg No. CEPZ/C-TD/013/13 (Sheet 1/5 to5/5), complete all as specified.

SCHEDULE 'A' PART-I:-Taking down point wiring with aluminium/ copper conductor for light point, socket point/ power point etc. on teak wood batten with clips including taking down wooden board complete with any type of switches, sockets, holders, (batten or pendent type), ceiling rose etc. The light fittings (any type), main switches, distribution board with MCB’s of any capacity and make are to be removed/replaced if required and all as specified and directed. NOTE: - Existing fan regulator (any type) is to be refixed and connected properly where required.

Taking down sheet metal enclosure DB, MCB, main switch etc and making good distrubed surfaces to match with existing surfaces, complete all as specified.

Point wiring with 1.5 Sqmm copper conductor FRLS (Multi strand) PVC insulated ISI Marked unsheathed cable in and including concealed PVC conduits, medium grade, ISI marked not less than 20 mm dia and conforming to IS-9537 (Part-II) 1983 with all fittings/ accessories and also including PVC insulated ISI marked unsheathed 1.5 Sqmm copper multistranded conductor FLRS as earth wire connected to common earth dolly and including pressed steel/ cast iron of suitable sizes terminal boxes made from 1.60 mm thick sheet for mounting of switches, sockets, fan regulators, light fittings etc. covered with 3mm thick plastic laminated sheet (Make Hylum or equivalent ISI marked) for one light point or one fan point or one bell point, independent, controlled by one way switch/ push button complete all as specified and directed.

All as per serial item No '134', above, but for one 3 pin 5 Amps socket outlet on the independent board, all as specified and directed.

All as per serial item No '134' above, but for one 3 pin 5 Amps socket outlet on the same board all as specified and directed.

All as per Srl item No. '134' hereinbefore but for 3 pin 15 amps socket out let on independent with 2.5 Sqmm PVC copper conductor cable and PVC insulated, unsheathed 2.5 Sqmm stranded copper conductor cable as continuous earth wire, all as specified.

Switch piano flush type, single pole, one way, 5/6 Amps, all as specified.

Switch socket outlet Two -in -One 3 pin 5 amps flush type, 230 volts AC multipurpose all as specified.

Switch socket combination 5 Pin, 5 Amp & 15 Amp flush type all as specified.

Ceiling rose, three phase, PVC/Polycarbonate, insulated body, all as specified.

New E-Lite LED triyca batten. A Color changing LED batten with options of 3000K, 4000K & 6500K, all in one fxture, 20 watt LED and making connection with 3 core copper flexible cable of size 23 x .0076 from ceiling rose/ PVC connector to light complete. Make:- Havells Cat Part No.LHEXBYPNIN1W020 or equivalent in makes mentioned in Appx 'C'.

PLUTO Neo PANEL 2X2, 34 Watt Environmental friendly, new generation,aesthetically designed, ultra modern recess mounting luminaire with high brightness SMD LEDs as light source, suitable for Armstrong/Grid ceiling. including connecting up with twin core twisted flexible copper conductor cable with suitable size, all as specified. Make : Havells Cat Part No.PLUTONEO2X2PLR34WLED857S OR equivalent in makes mentioned in Appendix 'C'.

ENDURA PEARL , 25 Watt LED, 5700K, New generation energy saving and environmental friendly long life LED street light made up of pressure diecast aluminium housing with high power LED as lighting source and lens embedded PC cover having TOP Opening seperate driver compartment with IP65 protection and impact resistance of IK07 including connecting up with twin core twisted flexible copper conductor cable with suitable size, all as specified. Make : Havells Cat Part No.ENDURAPEARLSL25WLED757SASYTOPC OR equivalent in makes mentioned in Appendix 'C'.

Supply and hanging ceiling fan with complete fixing arrengement of size 1200 mm sweep blade including provision of copper multi stranded PVC insulated 1100 volts grade three core flexible cable for main connection with existing ceiling rose at point wiring complete all as specified and directed by Engr-in-Charge.Make ;-Havells /CG /BAJAJ

Taking down ceiling/ exhaust fan any sweep from fan hook or walls, dismantling blades, opening motor, cleaning stator, cleaning all parts, greasing, oiling of bushes & bearings, reassembling ceiling fan, refixing and making connections with 3 core copper flexible cable of size 23 x .0076 from ceiling rose/ PVC connector to fan complete all as specified.

Ceiling fan regulator step type, electronic type varying 5 Speeds 230 Volts,50Hz, suitable for 1200/1400 mm sweep ceiling fans, all as specified.

Sheet metal enclosures for DBs when MCBs to be used, single pole and neutral (double Door), 8 way, 240 volts with 200 Amp rated bus bar, all as specified.

Sheet metal enclosures for DBs when MCBs to be used, single pole and neutral (double Door), 4 way, 240 volts with 200 Amp rated bus bar, all as specified.

MCB SP 6 to 32 Amp, 240 Volts, 10 KA all as specified.

MCB SPN 06 to 32 Amp, 415 Volts, 10 KA all as specified.

Sub main wiring with two single core PVC insulated cable 1100 volts grade with copper stranded FRLS conductor of size 6 Sqmm (2 single run) with one continuous FRLS copper earthing lead wire of size 6 Sqmm and drawn into and including concealed PVC conduit/ PVC casing & capping of 25mm dia with all fittings/ accessories, junction boxes 1 to 4 way 25mm dia and connected to common earth dolly, complete and as directed. Note :- Two run (each run of 1 RM) of 6 sqmm copper conductor and one RM of earth wire of 6 Sqmm, shall be measured as one RM).

Sub main wiring with two single core PVC insulated cable 1100 volts grade with copper stranded FRLS conductor of size 4 Sqmm (2 single run) with one continuous FRLS copper earthing lead wire of size 4 Sqmm and drawn into and including concealed PVC conduit/ PVC casing & capping of 25mm dia with all fittings/ accessories, junction boxes 1 to 4 way 25mm dia and connected to common earth dolly, complete and as directed. Note :- Two run (each run of 1 RM) of 4 sqmm copper conductor and one RM of earth wire of 4 Sqmm, shall be measured as one RM).

Supply & fixing Glaze LED Batten LED 20 Watt, 6500 CCT (k) surface and wall mounted LED batten, high quality aluminium extruded with decorative end caps with polycarbonate diffuser and including connecting up with twin core twisted flexible copper conductor cable with suitable size. Make : Jaquar item code LGLZ01X020XC equivalanet in Bajaj/Crompton/Polycab

m/s saurabh mahajan