103/EDCB/2022-23

Amount

The work of safe carriage of the following material from CB Ganj store center to work site under the jurisdiction of EDD-Baheri Approx. distance upto 80 Km. Including safe loading and unloading.

PCC Pole 8.5 Mtr

ACSR Weasal Conductor

AB Cable 3x50 sqmm

11/0.4 KV 3 Phase 400 KVA T/F

11/0.4 KV 3 Phase 250 KVA T/F

11/0.4 KV 3 Phase 63 KVA T/F

LT Cable 1x400 sqmm

LT Cable 1x240 sqmm

Other Line material i.e., 33 KV & 11 KV pin insulater/stay/earthing complete/Disc Fitting/Disc Insulators/Dropper Channel/Crossing Bracing/ Top Channel/Binding Wire/Danger Board/Barbed Wire/numberplate/stone pad/Control Cable etc

Construction of T/F plinth 1.5x1.5x2 m3 for mounting 250 KVA T/F including foundation work (below ground 0.5 M), Brick work, RCC slab of 4” thickness and plastering in 1:6 ratio with 02 Nos channel pieces of 1.5 mtr long of size 100x50x6 mm compete in all respect

Cage fencing of 250 KVA Plinth mounted transformer in Town areas to avoid electrical human/cattle accidents by fabrication of cage (1 Inch Sq wiremesh) made of 10 No gauge in suitable size angle iron frame of size 7.5'(L)x5'(W)x8’(H) by strenghtening of wire mesh 20x3 mm M.S. flat haorizentally as well as vertically, Grouting the panel with 1:2:4 cement/coorse send/brick ballast. The Frame should be bolted on angles at the four corners so that frame may be un-bolted/bolted at the time of replacement of the transformer. Provision of 1 gate should be there for maintenance of the transformer. Painting (1 coat of red oxide + 2 coat of Bus green enamel paint). The wire mesh should be earthed with 50x6 mm MS earthing strip with existing earthing of Transformer Body. All men, material and T&P provided by the contractor to complete the fabrication, transportation and installation.

Dismentaling of 250 KVA Transformer as per norms complete in all respect

Dismentaling of 100 KVA Transformer as per norms complete in all respect

Mounting of 250 KVA T/F Transformers as per norms complete in all respect -

Mounting of 400 KVA T/F Transformers as per norms complete in all respect -

Mounting of 63 KVA T/F Transformers as per norms complete in all respect -

Erection of Single/Double pole in H.T/L.T lines including fitting of all accessories as per RESSPO Norms

PCC Pole 8.5 Mtr (Single)

PCC Pole 8.5 Mtr (Double)

Laying of LT Cable 1x400 sq mm complete in all respect

Laying of LT Cable 1x240 sq mm complete in all respect

The work of Driving the earthing electrode and making connections with 6 S.W.G. GI wire as per RESSPO Norms

Laying, Stringing & Sagging of Following Conductor complete in all respect

ACSR Weasal Conductor

AB Cable 3x50 sqmm

The work of digging of pits, erection of Stay Clamp, Insulator etc.

Grouting of stays, 1:4:8 cc ratio (600x600x300mm.) as per RESPO norms.

Fixing of 3 Pahse Distribution Box complete in all respect

Supply and Fixing of Following Material as per RESPO norms complete in all respect (would be Provided by contractor through approved vendors of Discom at his own cost)

X-Arm M.S. Angle 65x65x6 mm V-Type

Sub Staion Base Angle

F Bracket

Aluminium Lug 400 sqmm with Nut&Bolt

11 KV Pin Insulator with pin Nut & Bolt

11 KV Disc Insulator with Fitting

Holding Clamp

M S T-Off Channel with clamp

Dropper Channel

LT Clamp & J Hook

Top Channel

Safe back carriage of Following item (if any) from work site to C.B. Ganj store Bareilly approx distance upto 10-80 Km including loading & unloading.

Scrap

11/0.4 KV 3 Phase 250 KVA T/F

11/0.4 KV 3 Phase 100 KVA T/F

Qazi contractor and suppliers

JOSHI ELECTRICALS