SPECIAL REPAIR TO TWO TOILET AND BATHROOM BLOCK (GROUND FLOOR) OF OTM ACCN BLDG No P-982 OF SATA REGT AND OTHER SANCTIONED WORKS UNDER THE AREA OF AGE B/R-I AT GE (ARMY) No.1 JODHPUR

Surface excavation n.exc 30 cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified.

Excavating in trenches, n exc 1.5m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and getting out in any type of soil complete all as specified and directed.

Excavating in post holes (of similar holes) each n. exc. 0.50 cum getting out, returning filling in and ramming earth or broken rubble mixed with earth around, in layers not exc 25cm, watering and removing surplus soil to a distance n. exc. 50m and making good surface complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick of excavated soil complete all as specified and as directed.

Removal of excavated soil to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed.

Demolition of cement concrete in ground floors and pavings not exc 15 cm thickness (below or above ground level) and removal unserviceable materials, debris and rubbish to a distance out side MD land complete all as specified and directed.

M&L for hardcore of broken stone or boulders of gauge n exc 63mm deposited, spread, levelled in layers n exc 15cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for sand filling under floors, including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick complete all as specified and as directed.

M&L for squared rubble walling, Jodhpur type, regular coursed well bonded, bedded and solidly hearted built in cement mortar 1:6, complete all as specified and directed.

Extra over stone walling for hammer dressing to face stone & dressing of face beds & joints as specified of squared rubble walling Jodhpur type brought upto courses with maximum depression of face from straight edge held against the dressed surface n exc 20mm and dressing face beds and joints, complete all as specified and directed.

M&L for Plain cement concrete 1:4:8 type D-2 by using 40 mm graded crushed stone aggregate as in foundation, filling and mass concrete, in flooring path, sub foundation etc, complete all as specified and as directed .

M&L for Plain cement concrete 1:3:6 type D-2 by using 40 mm graded crushed stone aggregate as in foundation, filling and mass concrete, in postholes, flooring path, sub foundation etc, complete all as specified and as directed .

M&L for 25mm thick Plain Cement Concrete Type B0 1:2:4 (using 12.5 mm graded stone aggregate) in sub base, floors, pavings complete all as specified and directed.

M&L for Jodhpur stone roof slabs, self faced 7.5cm to 10cm thick, 25cm to 35cm wide, hoisted and set, jointed and grouted in cement mortar 1:6 complete all as specified and directed.

M&L for Vitrified Ceramic tiles light shade double charged 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match etc including over 15 mm thick screed bed or bedding layers in CM (1:6) for laying in floors finishing complete all as specified and directed.

M&L for non-skid coloured ceramic tiles joint free 7 to 8mm thick (Square/Rectangular) area of each tiles exc 0.06 Sqm but n exc 0.11 Sqm in floors set and jointed in neat cement slurry and pointed in coloured cement to match including over 15 mm thick screed bed or bedding layers in CM (1:6) for laying in floors finishing ,complete all as specified and directed.

M&L for non-skid coloured ceramic tiles joint free 7 to 8mm thick (Square/Rectangular) area of each tiles exc 0.11 Sqm but n exc 0.18 Sqm in floors set and jointed in neat cement slurry and pointed in coloured cement to match including over 15 mm thick screed bed or bedding layers in CM (1:6) for laying in floors finishing ,complete all as specified and directed.

M&L for glazed colour ceramic tiles (premium quality) of size 300 X 600 X 7-8 mm, as in vertical surface such as dado/skirting etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, over & including 10mm thick backing coat in CM (1:3) complete all as specified and directed.

Taking down existing cement plaster on brick or stone walls, ceilings etc., including raking out joints, hacking for key, scrubbing down with water, etc. complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:6 on stone masonry surfaces finished even and smooth without using extra cement complete all as specified and directed.

M & L for rendering 15mm thick in CM 1:4 on other than fair faces of solid PCC block surface or concrete surface finished even and smooth using water proofing compound without using extra cement complete all as specified and directed.

M&L for rendering 5mm thick on fair faces concrete surfaces in CM 1:3 and finished even and smooth in ceilings/chajjas surfaces without using extra cement complete all as specified and directed.

Supply only integral water proofing compound complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of ceilings and applying three coats of white wash complete all as specified and directed.

M&L for preparation of newly plastered or pointed surfaces of walls and applying three coats of white wash complete all as specified and directed.

M & L for preparing new plastered surfaces of walls and applying two coat of Oil Bound distemper over 2mm thick wall care putty over a coat of alkali resistant primer and complete all as specified and directed by Engr-in-charge.

M&L for raking out joints/ pointing to squared rubble masonry, jodhpur type regular course built in cement mortar complete all as specified and directed.

M&L for keyed pointing to square rubble masonry Jodhpur type regular course in CM 1:3 complete all as specified and directed.

M&L for preparing newly plastered or unplastered surfaces of walls and applying two coats of cement base paint over a coat of primer, Priming the plastered and other surface with alkali resistant priming paint complete all as specified and directed.

M & L for preparation of newly plastered surfaces of wall and applying with 2mm thick wall care putty over one coat of primer on walls including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surface and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489: 2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed.

M&L for Precast cement concrete 1:2:4 type B1 (20mm graded aggregate) solid block masonry exc. 10 cm in width and setting in cement mortar 1:4 complete all as specified and directed.

M&L 16-18 mm thick granite stone (of any type) as in steps, jambs, urinal partition, pillars, window cills, counter type platforms & similar nature works, machine cut, (table rubbed and polished) best quality as per sample, in CM 1:4 including rounding & double mouldlng with jointless finish of the edges, including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

Taking down Chowkats or frames not exceeding 1.5 Sq. M each (Without taking off shutters from the frames) complete all as specified and directed.

Taking down Chowkats or frames exceeding 1.5 Sq. M each and n exceeding 4.0 Sqm each (Without taking off shutters from the frames) complete all as specified and directed.

S&F 300mm long and 16mm dia, Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

S&F 150 mm long extruded Aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F 150 mm long Aluminium, anodised, barrel tower bolts of extruded section complete all as specified and directed.

S&F 100 mm long medium weight, cold rolled Stainless steel Butt hinges complete all as specified and directed.

S&F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified and directed.

M&L for Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardantFactory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete all as specified and directed. Note: (a)-For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. (b)- M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately.

S&F factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and directed.

M&L for fabrication of Anodised aluminium powder coated aluminium framewok as in frames of doors, windows and ventilators, fixed type without sash bar or sliding type(2/3 track) or with louvers having suitable mechanism for tilting u shaped fillets, aluminium section weighing 0.55 kg/m including necessary joining cleats. glazing clips, rubber packing. anodised aluminium snap beading. screws etc. complete all as specified

S&F powder coated anodised aluminium door shutters (minimum thickness of powder coating 50 micron), aluminium section weighing minimum 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, 2 tower bolts, 1 mortice lock of vertical type brass 4 levers size 65mm and anodised aluminum snap beading screws etc. complete all as specified

S&F powder coated anodised aluminium window shutters prepared for sliding or hanging or fixed type etc with aluminium sections weighing minimum 0.55kg/m incl necessary joining cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading, screws and also including handles, tower bolts, locks and hinges etc complete all as specified and directed by Engr-in-charge.

S&F 4mm thick sheet glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane complete all as specified as directed.

S&F aluminium alloy wire cloth 0.45 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with aluminium wire stapler complete all as specified and directed.

S&F 3mm thick sheet glass ordinary quality frosted on one side n exc 0.50 sqm in each pane complete all as specified and directed

S&F counter type Vitreous china wash basin white/coloured size 630X450 mm fixed over granite and RCC slab including 15mm bore swan neck pillar taps cast copper alloy chromium plated fancy type, with capstan heads, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shank and fly nuts, screwed for iron pipe fixed with CP waste coupling 32mm and waste pipe complete all as specified and directed.

M&L for 32mm bore Brass chromium plated Bottle trap for wash basins with inlet and outlet screwed for pipe or connections incl necessary packing union and cap etc complete all as specified and directed.

S & F in repairs Vitreous China Squatting pan of Orrisa pattern, long pan, size 580mm x 440mm white with `P' or `S' trap, front or back inlet and integral foot rests any pattern including connection to trap and to flushing pipe of 32mm dia, etc incl PVC connections 15mm dia , 450mm long, with PTMT nuts & washers at both ends and fixing arrangement of cistern complete all as specified and directed.

S&F in repairs vitreous China wash down water closet pan European type pedestal pattern, white with seat and cover including PVC 'P' or 'S' trap, flush HDPE pipe of 32 mm dia and fixing arrangement of cistern including S&F of CP Hand Shower (Health Faucet) with 8mm dia, 1.2 Mtr long flexible tube & wall hook with N.R.V (Back flow preventer), 15 mm dia complete all as specified and as directed.

S&F 10 ltrs capacity PVC valve less, ISI Marked syphonic action type, flushing cistern, low level, with Anti Bacterial Knob, with inlet, ball valve, float and handle including brackets, flush pipe of 32 mm dia and PVC connection, cistern colour shall be match WC colour, complete all as specified and as directed.

S&F in replacement of single piece EWC with slim soft close seat cover complete set constellation dual flush WB constellation 5 ped constellation, EWC, cistern & lid CON dual flush, seat cover constellation, cistern fitting (water saver dual flush) etc complete all as specified and directed.

S&F Vitreous China Urinal, Half stall type, white including providing and fixing of plugs bedding against wall in CM 1:2 pointing around urinal back in cement mortar including Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms) including PVC connection and bottle trap of 32mm dia complete all as specified and directed.

S&F 15 mm bore long body bib cock with wall flange and aerator, brass chromium plated with fancy type and screwed down to 15 mm bore GI tubing or for brass ferrule including taking down old bib cock complete all as specified and directed.

S&F 15mm bore pillar taps with aerator, cast copper alloy, with capstan heads, fancy type chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for iron pipe and fixed complete all as specified and directed.

S&F chromium plated Wall mixer 3-in-1 system including adujstable wall flange complete all as specified and directed.

S&F chromium plated shower rose 150x150mm size with or without swivel joint, any size including fixing to steel pipe suitable for 15mm bore pipe etc; complete all as specified and directed.

S&F tubular towel rail brass chromium plated fancy type 20mm dia and 60 cm long fixed between flanges complete all as specified and directed.

S&F 15mm bore Stop valve / angle stop valve with wall flange, brass chromium plated, long shank and cup, screwed down, high pressure, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F in repair Soap dish, chromium plated, any type, as approved fixed with brass screws or embedded in wall complete all as specified and directed .

S&F 15 mm bore two way bib tap with wall flange and aerator, brass chromium plated with fancy type and screwed down to 15 mm bore GI tubing or for brass ferrule complete all as specified and directed.

Dismantling water tanks exc 500 Ltr but n exc 1000 ltr and removing to store complete all as specified and directed.

S&F Rotational moulded polythene water storage tanks of 500 ltrs capacity, white three layered (ISI marked) (Cylindrically vertical with closed top) hoisted and fixed in postion all as specified in SSR Part-I with PTMT ball valve high pressure with epoxy coated aluminium rod and high density plastic ball suitable for 20mm bore pipe weight not less than 210gms complete all as specified and as directed.

S&F Rotational moulded polythene water storage tanks of 1000 ltrs capacity, white three layered (ISI marked) (Cylindrically vertical with closed top) hoisted and fixed in postion all as specified in SSR Part-I with PTMT ball valve high pressure with epoxy coated aluminium rod and high density plastic ball suitable for 20mm bore pipe weight not less than 210gms complete all as specified and as directed.

Taking down steel window / ventilator complete all as directed.

Taking up or down 25mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed.

All as per item No.69 here in before but 20mm outer dia pipes.

All as per item No.69 here in before but 15mm outer dia pipes.

Supply & laying of 25 mm dia CPVC pipe SDR 11 and with plain CPVC SDR 11 fittings such as bends, elbows, unions and end pieces to receive the fittings, concealed in walls/ceiling or lay in floors and fixed with solvent including cutting chases, pinning in & making good disturbed portion complete all as specified and as directed.

All as per item No.72 here in before but 20mm outer dia pipes.

All as per item No.72 here in before but 16mm outer dia pipes including cutting chases, pinning in & making good to disturbed portion to match the existing surface etc complete.

All as per item No.72 here in before but 40mm outer dia pipes.

S&F gun metal, globe or gate valves 20mm bore, with iron wheel head, screwed both ends for iron pipe complete all as specified and directed.

S&F gun metal, globe or gate valves 25mm bore, with iron wheel head, screwed both ends for iron pipe complete all as specified and directed.

S&F PVC connections 15mm dia , 450mm long, with PTMT nuts & washers at both ends complete all as specified and directed.

S&F PVC connections 15mm dia , 600mm long, with PTMT nuts & washers at both ends complete all as specified and directed.

Supply and fixing PVC waste pipes of 40/32mm bore suitable for wash hand basins/Urinal complete all as specified & directed

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to walls incl stack clamps of 50mm x 3mm MS flat iron with bolts & nuts complete all as specified and directed.

Supply & laying 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches of suitable size complete all as specified and as directed .

Supply & laying 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches of suitable size complete all as specified and as directed .

S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to walls incl stack clamps of 50mm x 3mm MS flat iron with bolts & nuts complete all as specified and directed.

S&F 110mm bore PVC [SWR] branch piece, single (single Y) equal or unequal complete all as specified and as directed.

S&F 110 mm bore (SWR) PVC bends any radius, complete all as specified and directed.

S&F 75 mm bore PVC(SWR) bends any radius with access door, complete all as specified and directed.

S&F 110 mm bore PVC (SWR) vent cowl complete all as specified and directed.

S&F 75 mm bore PVC (SWR) vent cowl complete all as specified and directed.

S&F in repairs 75mm bore PVC (SWR), junction single, single T equal or unequal complete all as specified and as directed.

S&F 110mm bore PVC (SWR), junction single, single T equal or unequal complete all as specified and as directed.

M&L 75mm PVC(SWR) floor trap concrete type B-1 (1:2:4) with grating including jointing to waste pipe fixed in cement with CP grating complete all as specified and directed

S&F 100mm PVC (SWR) floor trap plain with CP grating including jointing with solvent cement dia, complete all as specified and directed.

M&L for 75mm dia PVC (SWR) multifloor trap, with grating including jointing with solvent cement complete all as specified and directed.

S&F CP Hand Shower (Health Faucet) with 8mm dia, 1.2 Mtr long flexible tube & wall hook with N.R.V (Back flow preventer), 15 mm dia complete all as specified and directed.

S&F sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

M&L for fabrication of aluminium powder coated ventilators (with louvered) fabricated with anodized aluminium rectangular section in frame & with deco grill of approved design & stainless steel wire cloth on the outer side of frame & trade pattern louvers with suitable mechanism for tilting / opening closing etc all as per sample approved by GE & fixed in position complete all as directed. (Note : Glass pane in louvers & stainless steel wire cloth shall be measured & paid separalely)

S&F4 mm thick pin headed fiqured glass in small widths as in Iouvers of ventilators complete all as directed.

S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed to anodised aluminium frame work of windows / ventilators with stainless steel wire staples complete all as specified and directed.

M&L for PCC 1:4:8 type D2 (using 40 mm graded granite stone aggregate) as in concrete bed to drain pipes 150mm bore including packing under and haunching against the sides of pipes after they are laid and tested complete all as specified and as directed with adherence to following conditions: (i) Hanuching over offset of foundation of manhole shall be measured alongwith foundation of manhole. (ii) Thickness of concrete bed shall be 10cm. (iii) Pipe shall be measured and paid for separately.

Supplying, laying, jointing and testing of 150 mm dia Reinforced concrete pipes, class NP2 laid and jointed in cement mortar 1:1 complete with collars or socket/ spigot type, drain pipes laid in trenches and jointed complete all as specified and as directed.

M&L for cutting into existing manholes for connecting new drains with 150mm internal dia of pipe, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) 1:2:4 type B1 smooth finished & reforming benching as reqd complete all as specified and directed.

M&L 100mm thick PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate), as in sub base to floor, incl well compacting & laid to levels etc, complete all as specified and directed.

Supply and laying machine pressed / factory made chamfered edge cement concrete rubberised interlocking paver block, 60mm thick with 6 mm thick top layers of anti abrasive material of M-35 grade with any colour, design & pattern, & size/ shape, as approved by GE as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness made by table vibratory method using PU mould, laid in required colour & pattern over and including M&L 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, complete all as specified and directed.

M&L Providing Cement concrete (1:2:4) type B-0 using 12.5 mm graded stone aggregate in roof kerbs or mud stops, rounded or chamfered on edges and coping complete all as specified and directed.

M&L for plain cement concrete 1:2:4 type B-0 (using 12.50mm graded stone agg) as in roof padding over cleaned surfaces of roof for making good any depression/undulation and to obtain desired slopes complete all as specified and directed.

M&L for rendering 20mm thick in cement mortar (1:4), mixed with integral water proofing liquid all as per manufacturer's instructions over concrete surfaces finished even and smooth with out using extra cement complete all as specified and directed.

M&L for carrying out water proofing treatment for roofs in the following stages - (i) Material and labour for UV stable single component fibre reinforced elastomeric liquid applied waterproofing membrane having solid content of 55% formulated wih PU hybrid polymers and reinforcing acrylic fibres and having sun reflectivity Index (SRI) of 106. The application of the material should be done in three coat (6 hr gap after each coat) on the substrate, applying first self priming coat at ratio of damp proof ultra and water 3:1 then 2 undiluted coat of damp proof ultra obtaining coverage @1 ltr/10 sqft in two coats (10-12 hrs gap between each coat. The vital physical and chemical parameters shall be as under. Min elongationat break of 350%, crack bridging ability of 2.5 mm @650 microns thickness, resists positive hydrostatic pressure of up to 10 bars. The material shall be appliied with brush or roller, complete in all respect as per the direction of Engr-in charge/consultant. Also, proper surface preparation along with covingat corners is must, complete all as specified and as directed. Note : - (i) The work shall be executed by the authorized applicator of the manufacturer only. (ii) The authorized applicator of manufacturer shall be approved by GE. (iii)The color of final finish shall be decided by the GE (iv)WPC shall be measured separately and paid for under respective item of schedule).

M&L for providing and fixing 10mm thick plaster of paris (gypsum anhydrous) to raised moulding surface over 2nd class softwood fillets or metal framework and reinforced with GI wire mesh any type of design and pattern all as specified and directed.

M&L 12mm toughened glass as in partitions and similar work including cutting to shape, drilling holes required including all necessary fittings complete all as specified and directed.

S&F rolled mild steel sections as in main and cross beams (ISMB 150), hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates confirming to Fe 410-W(Gde E-250) quality A, complete all as specified and as directed.

S&F framed work such as grills, gratings etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; frame work of water tanks and similar work confoming to Fe-290 Gde-E-165 or ornamental type of angle or other section with gusset plates, rails, braces etc complete drilled for fixing of steel post etc to prepared for hanging or sliding with and including either hooks and hinges or other covering running rails and guides incuding forging item (tersule etc) and hanging also fastening and fixing complete all as specified and directed.

S&F of Decooline PVC fluted wall panel design SF 742 of size 1200 x 2400mm PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specification and drawing complete all as specified and as directed.

M&L preparation of steel and steel base surfaces over 10 CM width or girth and applying two coats of synthetic enamel paint over one coate of red oxide primer complete all as specified and as directed.

Taking down carefully alluminium / copper point wiring complete for light, fan, socket or power point etc with fittings fixtures such as ceiling rose, holders, electric fittings, switchs, sockets, aluminium conductor cable with and incl wooden batten or FR PVC conduit and its accessories such as wooden gutties, rawl plugs, GI screws, aluminium clips, nails etc complete and removing the material from site and making good the disturbed surface of wall / floor/ ceiling etc as original i.e. brick work, plastering, white washing, OBD etc as required, complete all as specified and directed.

Taking down carefully UNSV main switch and DB's including MCBs of any size make, type and capacity and depositing at site complete all as specified and directed.as directed.

Taking down carefully UNSV Submain wiring of any size complete all as specified and directed.

M&L for (concealed) point wiring complete with multistranded copper conductor 1.5 Sqmm PVC insulated unsheathed single core FRLS cable 1100 volt grade, confirming IS 694 & colour code in conduit system of wiring, drawn through in and including non-metalic PVC concealed (including Cutting Chases and make good the distrubed surfaces as per existing finishes) conduit of size 20 mm or med grade as required as site, totally concealed in walls / and surface on floors / ceiling or fixed on surface of walls / columns / beam / tie beam etc by means of saddles and clips etc incl all conduit accessories / fittings / junction boxes / inspection covers etc of heavy grade, ISI marked and sunk terminal boxes of CI or 16 SWG pressed steel housing, totally concealed in walls with 3mm thick industrial laminated sheet top cover, fixed flush with wall surface by means of brass screws and sunk / cup washers, for mounting of switches, sockets fan regulators etc incl 1.5 Sqmm FRLS PVC insulated, unsheathed flexible multi stranded copper conductor cables as continuous earth wire connected to metallic bodies of luminaries / fans etc at one end and to common earth dolly at other end, suitable for One light point controlled by one, one way switch, complete all as specified and directed. Note:- The rates of chase cutting on wall done concealed conduit & making good good the distrubed surfaces as per existing finishes and steel terminal boxes are included in the unit rates

All as per Sr. item No.118 here-in-above, One fan/Exhaust fan point controlled by one way switch

All as per Sr. item No.118 here-in-above, but suitable for One socket outlet 3 pin, 5 Amps on independent board, controlled by one no 5 Amp switch.

All as per Sr. item No.118 here-in-above, but suitable for One socket outlet 3 pin 5 amps on the same board controlled by one no 5 Amp switch.

All as per Sr. item No.118 here-in-above, but with using 2.5 Sq mm FRLS copper wire with 2.5 Sq mm FRLS copper earth wire 15 Amp socket outlet on independent board complete all as specified and directed.

M&L for modular point wiring complete with multistranded copper conductor 1.5 Sqmm PVC insulated but unsheathed single core FR-LSH cable (RYBN) 1100 volt grade, confirming IS 694 & colour code in conduit system of wiring, drawn through in and including non-metalic PVC heavy duty concealed (including Cutting Chases and make good the distrubed surfaces as per existing finishes) conduit of size 20 mm or med grade as required as site, totally concealed in walls / and surface on floors / ceiling or fixed on surface of walls / columns / beam / tie beam etc by means of saddles and clips etc incl all conduit accessories / fittings / junction boxes / inspection covers etc of heavy grade, ISI marked and sunk terminal boxes of CI or 16 SWG pressed steel housing, totally concealed in walls with 3mm thick industrial laminated sheet top cover, fixed flush with wall surface by means of brass screws and sunk / cup washers, for mounting of switches, sockets fan regulators etc incl 1.5 Sqmm FR-LSH cable (Green) 1100 volt grade, PVC insulated but unsheathed flexible multi stranded copper conductor cables as continuous earth wire connected to earth dolly and including modular sunken galvanized terminal boxes of same make of switch/socket/regulator with sleek and curvy cover plates, for mounting of modular swithces, sockets, fan regulators complete, suitable for One light/fan/bell point controlled by one, one way switch, complete all as specified and directed. Note:- The rates of chase cutting on wall done concealed conduit & making good good the distrubed surfaces as per existing finishes and steel terminal boxes are included in the unit rates

All as per Sr. item No.123 here-in-above, but One socket outlet 5 pin 5/6 amps on the same board controlled by one no 5/6 Amp switch.

All as per Sr. item No.123 here-in-above, but One socket outlet 5 pin 5/6 amps on the independent board controlled by one no 5/6 Amp switch.

All as per Sr. item No.123 here-in-above, but with using 2.5 Sq mm single core multistranded copper conductor cable for 3 pin 16 Amp socket outlet on independent board complete all as specified and directed.

S&F Socket, two-in-one, 5 Pin, 5 Amp, universal type, 230 volts, complete all as specified and directed.

S&F Switch piano type, single pole, one way, 15/16 amps, 230 volts, complete all as specified and directed.

S&F Socket, 6 pin, 5/16 Amp, multipurpose shutter type , 230 volts, complete all as specified and directed.

S&F Switch piano flush type, single pole, one way, 6 amps, 230 volts, ISI marked complete all as specified and directed.

S&F modular switch 1 way 6 Amp, 1 module complete all as specified and directed.

S&F modular switch 1 way 16 Amp, 1 module complete all as specified and directed

SSF modular socket 6 Amp 2/3 pin, combined 2 module complete all as specified and directed

S&F modular socket 6 Amp/16 Amp, 6 pin, combined 2 module complete all as specified and directed

S&F Lamp holder, metal cased, bakelite body, 230 volts, complete all as specified and directed.

S&F LED lamp 9W complete all as specified and directed by the Engineer-in-Charge.

S&F Ceiling rose, two to three terminals, bakelite body, 230 volts, complete all as specified and directed.

Supply and fixing LED lights fitting 1x 20W,4 ft long, T-5 batten fitting, designed linear sleek aesthetic PVC housing, PC cover ensures soft and glare free lighting wide angle of 120 degree, upto (110Lm/W) complete all as specified and as directed.

S&F bldg security LED Light Luminaire of 35 Watts having IP 65 protection fiting made out of pressure die cast Aluminium housing, operating Voltage 140-270 Volts with in built surge protectore, toughened glass with and including GI pipe 40 mm bracket of 1.5 m in length including drilling holes, nuts & bolts 2 coats of red oxide primer on GI pipe and fixing with wall security light on building wall connecting cable, complete all as specified and as directed.

S&F LED light fitting mirror type with high output diffuser 2 feet, 10 Watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

Supply and fixing round shape 12 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamps suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

S&F of Heavy duty Exhaust fan 300 mm sweep, 900 RPM, including louvers with cutting chases on brick wall and grouting with nut bolts, complete all as specified and as directed.

S&F Ventilation fan metal body 230 mm sweep, including louvers with cutting chases on brick wall and grouting with nut bolts, complete all as specified and as directed.

S&F single pole arnd neutral enclosure with two pin and earth plug socket complete with one single pole MCB 20 Amp 'C' curve type, 230 volts, 10 KA complete all as specified and directed.

S&F MCB, B type curve, 10kA, 63 Amp, SPN with over load and short circuit protection complete all specified and directed.

S&F MCB, B type curve, 10kA, 6 to 32 Amp, single pole with over load and short circuit protection complete all specified and directed.

S&F MCB DB SPN (double door) 8 Ways including bus bar neutral link, earth bar and din rail, recessed with wall surfaces by chase cutting and making good surfaces of wall incl dismantling of old UNSV DB all as specified and directed by the Engr-in-Charge.

S&F in replacement sheet metal enclosures 415 volt TPN 4 way with 200 Amp rated bus bar, double door IP-43 DB's suitable for a MCB One No 100A 10kA TPN MCCB as incoming complete all as specified and directed by Engr-in-charge. Note: MCB/RCCB TPN/SPN/SP measured and paid saperately.

S&F in replacement MCB TPN C Curve 63 Amps Make incl dismtaling of old unserviceable TPN MCB complete all as specified and directed.

Supply, laying and testing in trenches/on wall / in duct/ through protection pipe LT UG XLPE insulated,armoured, heavy duty electric cable, aluminium coductor, 1100 V grade,croos sectional area 16 sqmm 2 core complete all as diredted by Engr - in - charge Note : Earth work and brick work measured and paid separately

M&L for sub main wiring with two runs of PVC insulated but unsheathed multi stranded copper conductor FRLSH cable 1100 volt grade of size 4 Sqmm and one run of 4 Sqmm single core PVC insulated but unsheathed multi stranded copper conductor FRLSH cable (Phase-Red, Neutral-Black, Earth-Green) 1100 volt grade as earth lead drawn through in and including non metallic PVC conduit of size 25 mm dia (external) with wall thickness not less than 1.8 mm, ISI marked concealed in wall including accessories like bends tees junction boxes, etc fixed in wall or ceiling etc. complete as directed by Engineer-in-Charge. NOTE: Two runs of cable with one run of earth wire and PVC conduit shall be measured & paid for as one Iength.

M&L for sub main wiring with 2 run of 6 Sqmm FRLS, PVC insulated, unsheathed and stranded copper conductor cable with and incl 6 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable as earth wire connected with thimble from main DB to sub main DB, drawn into separate concealed medium grade, ISI marked, non metallic PVC conduit 15mm dia size incl all conduit accessories & fittings / junction boxes / inspection covers etc with and incl cutting chasing and making good of disturbed surface of wall/floor/ceiling etc as original by brick work, plastering, white washing, OBD etc as required, complete all as directed. Note: Two runs of 6 sqmm and one runs of 6 sqmm (earth wire) including one run of PVC conduit shall be measured as one length incl making good the disturbed surfaces for the purpose of measurement.

M&L for sub main wiring with 5 run of 6 Sqmm FRLS, PVC insulated, unsheathed and stranded copper conductor cable with and incl 6 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable as earth wire connected with thimble from main DB to sub main DB, drawn into separate concealed medium grade, ISI marked, non metallic PVC conduit 25mm dia size incl all conduit accessories & fittings / junction boxes / inspection covers etc with and incl cutting chasing and making good of disturbed surface of wall/floor/ceiling etc as original by brick work, plastering, white washing, OBD etc as required, complete all as directed. Note: Four runs of 6 sqmm and one runs of 6 sqmm (earth wire) including one run of PVC conduit shall be measured as one length incl making good the disturbed surfaces for the purpose of measurement.

Supply,testing and installation of Electric water storage geyser of capacity 25 Ltrs, BEE 5 star rating, 230Volts, AC, 50Hz, comprising of heating element 2000 watt, storage type steel body with copper tank, puff insulation,both power indicating LED lamp and heating indicating LED lamp neccasry suitable 3 core copper cable,suitable plug top, inlcluding supply and fixing of inlet and out let connection to geyser with steel grip,chromium plated PVC connection of 862 mm in length - 02 Nos (one for inlet GI pipe and other one for outlet connection) suitable to connect inlet GI pipe 15mm dia and out let GI pipe 15mm dia (out let PVC connection should be capable to withstand the designed temparature of Geyser) and geyser shall be fixed on wall surface with wall mount bracket and 10 cm anchor bolts as required inclduing all necessary plumbling works and civil works complete all as directed and as specified.

M&L for Earthing complete with galvanised steel earth plate electrode 60x60cmx6 mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) wih top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 SSR Part-I 2009 and specified or indicated including excavation and earthwork in any type of soil PCC 1:3:6 type C1 in chamber, precast RCC 50mm thick in cement concrete 1:2:4 type B1, reinforced with welded steel wire fabric or XPM (Weight not less than 4.00 mm dia with cast iron frame, funnel with wire mesh, 20mm bore medium grade GI watering pipe, lugs, 15mm bore medium grade GI protection pipe, test point etc complete all as specified and directed. Note : (i) Item includes the cost of 7.5 metre GI pipe for protection of earth lead. (ii) Item includes the cost of 7.5 metre GI earth lead.

Supply and laying of sand for sand cushioning for cable protection in trenches including punning down of sand layer all as specified and directed. Note :- Punned thickness shall only be measured and paid.

Supply and laying unreinforced Precast concrete cable cover, class LV, type 1, flat size 300 mm x 180 mm x 40mm, complete all as specified and directed.

S&F GI tubing , light grade of 40mm bore with fittings as in road crossings for cable protection complete all as specified and as directed.

Note:- (i) Qty's have been clubbed from 4 Nos sanction Job's, whose details are encl as per appx. (ii) The contract sum shall be arrived at after deducting amount of schedule of "Credit" from the Total quoted amount.