Loading…
Loading…
Tender Value
₹5.6 L
EMD Value
₹14,000
Closing Date
9 Jul 2026, 3:00 pm
Similar tender results from the same govt authority in the past 3 years.
Divisional Engineer-(Elec-I), Tirupati
tpty
Providing wiring for the work of Construction of Pongal shed in the premises of Sri Venkateswara Swamy Temple, Ananthavaram(V), Thullur(M), Guntur district
950573
48/DE(Elec.)-I/TTD/TPT/2026-27
OPEN - NCB
Electrical Works
TIRUPATHI
6 documents required · 6 mandatory
₹198
₹14,000
24 Jun 2026
24 Jun 2026
24 Jun 2026
Supply and Fixing of ISI Mark 25mm outer dia medium grade (1.80mm thickness) with IS:9537 part -3 P.V.C. pipe with all accessories fixing on chromium plated metallic base saddles for surface wiring on Brick / stone walls, RCC roofings,Trusses, channels including all labour charges etc., complete. (If PVC Pipes are fixed on Trusses/Channels with MS Clamps, the rate for MS Clamps will be paid Separately)
Makes:Sudhakar/Finolex/Polycab / Kumar / AKG /Indian-tubes /GM / Anchor/ Nandi / Polyline / Gold Medal
Supply and Fixing of ISI mark 25mm outer dia medium grade (1.80mm thickness) with IS:9537 part -3 P.V.C. pipe for concealed wiring in new / existing brick building, walls, columns, beams duly cutting them to the required depth wherever necessary and fixing the pipes and specials with nails and plastering neatly with cement mortar and colour washing to match the finished surface and masonry work for light, fan and separate plug point including all labour charges etc., complete.
Makes: Sudhakar / Finolex / Polycab / Kumar / AKG / Indian-tubes / GM / Anchor / Nandi / Polyline / Gold Medal
Supply and Fixing of ISI mark 25mm outer dia medium grade (1.80mm thickness) with IS:9537 part -3 P.V.C. pipe for concealed wiring in walls of brick building duly cutting them to the required depth wherever necessary and fixing the pipes and specials with nails and plastering neatly with cement mortar and colour washing to match the finished surface and for surface wiring on chromium plated metallic base saddles on ceiling of roof / existing brick building walls, columns, beams, roofs / trusses / channel etc., and masonry work for light, fan and separate plug point including all labour charges etc., complete.
Make: Sudhakar / Finolex / Polycab / Kumar / AKG / Indian-tubes / GM / Anchor / Nandi / Polyline / Gold Medal
Supply and wiring with 3 run of 14/0.3mm (1.0 sq.mm) PVC insulated FRLS flexible copper cable (ISI MARK) as per IS:694 / 1990 specification in existing PVC pipes / casing & caping with 3 plate pilot ceiling rose, 6 Amp 1 Way Module Modular switch to switch control box including all labour charges etc., complete for Light, bell, fan and Exhaust fan points in Non-Residential Buildings.
Grade-B : Wire Makes: Atlas / Gold medal / Delton / Standard / GM / RPG / V-Guard / HPL / Anchor / Orbit Grade-B: Moduler Switch Makes: Legrand Myrius /Crabtree Thames Platinum / Anchor Roma / Clipsal / Havells Coral or Fabio / Goldmedal (Curve/Air) / Schneider Livia / C&S / L&T / HPL / GM (GNINE) / Kolars / Indo asian
Supply and wiring with 3 run of 14 / 0.3mm (1.0Sqmm) PVC insulated FRLS flexible copper cable (ISI MARK) as per IS:694 / 1990 specification in existing PVC pipes / casing & caping without ceiling rose, 6 Amp 1 Way Module Modular switch to switch control box including all labour charges etc., complete for Light, bell, fan and Exhaust fan points in Non-Residential Buildings.
Grade-B : Wire Makes: Atlas / Gold medal / Delton / Standard / GM / RPG / V-Guard / HPL / Anchor / Orbit Grade-B: Moduler Switch Makes: Legrand Myrius /Crabtree Thames Platinum / Anchor Roma / Clipsal / Havells Coral or Fabio / Goldmedal (Curve/Air) / Schneider Livia / C&S / L&T / HPL / GM (GNINE) / Kolars / Indo asian
Supply and run of 3 wire of 36/0.3mm (2.5 Sq mm) PVC insulated flexible FRLS copper cable as per IS:694 / 1990 specification in the existing PVC pipe / MS pipe /PVC Trunking for mains including all labour charges etc., complete
Grade-B : Makes: Atlas / Gold medal / Delton / Standard /GM / RPG / V-Guard / HPL / Anchor / Orbit
Supply and run of 6 wire of 36/0.3mm (2.5 Sq mm) PVC insulated flexible FRLS copper cable as per IS:694 / 1990 specification in the existing PVC pipe / MS pipe /PVC Trunking for mains including all labour charges etc., complete.
Grade-B : Makes: Atlas / Gold medal / Delton / Standard /GM / RPG / V-Guard / HPL / Anchor / Orbit
Supply and run of 3 wire of 56/0.3mm (4.0 Sq mm) PVC insulated flexible FRLS copper cable as per IS:694 / 1990 specification in the existing PVC pipe / MS pipe /PVC Trunking for mains including all labour charges etc., complete.
Grade-B : Makes: Atlas / Gold medal / Delton / Standard /GM / RPG / V-Guard / HPL / Anchor / Orbit
Supply and run of 6 wire of 56/0.3mm (4.0 Sq mm) PVC insulated flexible FRLS copper cable as per IS:694 / 1990 specification in the existing PVC pipe / MS pipe /PVC Trunking for mains including all labour charges etc., complete.
Grade-B : Makes: Atlas / Gold medal / Delton / Standard /GM / RPG / V-Guard / HPL / Anchor / Orbit
Supply and run of 5 wire of 84/0.3mm (6.0 Sq mm) PVC insulated flexible FRLS copper cable as per IS:694 / 1990 specification in the existing PVC pipe / MS pipe /PVC Trunking for mains including all labour charges etc., complete.
Grade-B : Makes: Atlas / Gold medal / Delton / Standard /GM / RPG / V-Guard / HPL / Anchor / Orbit
Supply and fixing of 6 /10 Amps 1 way 1 module Modular Switch on to the existing metal box (Switch Control Box) cover frame and giving necessary connections including all labour charges etc., complete.
Grade-B: Makes: Legrand Myrius / Crabtree Thames Platinum / Anchor Roma / Clipsal / Havells Coral or Fabio / Goldmedal (Curve/Air) / Schneider Livia / C&S / L&T / HPL / Kolors / Indo Asian / GM (GNINE)
Supply and fixing of 6 /10 Amps 2 pin 1 module Modular Socket on to the existing metal box (Switch Control Box) cover frame and giving necessary connections including all labour charges etc., complete.
Grade-B: Makes: Legrand Myrius / Crabtree Thames Platinum / Anchor Roma / Clipsal / Havells Coral or Fabio / Goldmedal (Curve/Air) / Schneider Livia / C&S / L&T / HPL / Kolors / Indo Asian / GM (GNINE)
Supply and fixing of 20 Amps 1 Way 1 Module Modular Switch with Neon Indicator on to the existing metal box (Switch Control Box) cover frame and giving necessary connections including all labour charges etc., complete.
Grade-B: Makes: Legrand Myrius / Crabtree Thames Platinum / Anchor Roma / Clipsal / Havells Coral or Fabio / Goldmedal (Curve/Air) / Schneider Livia / C&S / L&T / HPL / Kolors / Indo Asian / GM (GNINE)
Supply and fixing of 20 Amps 2 Module Modular Socket with Shutter on to the existing metal box (Switch Control Box) cover frame and giving necessary connections including all labour charges etc., complete.
Grade-B: Makes: Legrand Myrius / Crabtree Thames Platinum / Anchor Roma / Clipsal / Havells Coral or Fabio / Goldmedal (Curve/Air) / Schneider Livia / C&S / L&T / HPL / Kolors / Indo Asian / GM (GNINE)
Supply and Fixing of 4 feet T5, 18W LED Batten type fitting with Internal driver with Polycarbonate housing & PC diffuser suitable to operate on 230V AC, 50 Hz power supply as per the following specification. Make: Philips / Osram / Havells / Crompton Greaves / GE / Orkus
Specifications: 1. Input Power: 18W ±5% 2. Input Voltage and Frequency: 230V ±5% AC, 50Hz. 3. Power factor : >0.95 4. THD % : <15% 5. Operating Voltage : 140 - 270 VAC 6. Surge Protection : ≥ 2.5 kV 7. LED make: Nichia (Japan) / Osram (German) / Philips Lumiled / Cree (USA) / Bridgelux (USA) / Seoul / Lednim / Everlight / Epistar / Edison.
8. Luminous Flux (Lumen) : 1800 ± 5% 9. Luminous Efficiency (LM/W) : 100 ± 5% 10. Colour Temperature (K): 5500K to 6500K 11. CRI : ≥ 80 12. LED Beam Angle : >150º 13. IP Grade: IP20 Warranty : 5 Years. standards Applicable: IS: 10322 Part-5, Sec-3. Manufacturers internal Type Test Reports.
Supply and transportation of 50/60W LED Flood light Luminaire made of pressure diecast alluminium housing with powder coated, having protective toughned glass, supply input voltage 120-270 AC, PF>0.90, high power LED's system efficacy>100lm/W and Junction tempature < 70 degree C, with ingress protection IP66, Luminaire performance complies to IS 10322 (Part 5 / Sec-3), IK05, Driver surge protection 4KV, In house additional surge protection >10KV with wide / Narrow beam optics, THD<10% at 110 Volts AC, driver efficiency >90%, CCT:3000K-5700K, minium CRI>70, etc., complete.
a) LUMINAIRE MAKE : Wipro / Philips/ GE-Venture / Crompton/ Bajaj /Greenlites / Havells / Capart (Premium) /Halonix / Polycab / Keselec / HPL / Jaquar / Eveready / Surya (Lumasmax / O Flood) / FortuneArrt(Fin) b) LED MAKE : PHILIPS LUMILEDS / CREE / NICHIA / OSRAM / SAMSUNG.
Fixing of M.V / S.V / M.H luminaire / Halogen fitting on wall / pole cross arm / channel / stem pipe etc., including all labour charges and giving connections etc., complete.
Supply of 48" (1200mm) Sweep 5 star rated Ceiling Fan , with double ball bearings, air delivery more than 200 cubic meter/min but without Regulator. Makes : Crompton HS Plus / Havells ES Neo/ Orient Energy Star/ Halonix (Zephyr) / Polycab (Synergy Star) / G.M. (Air Wave Premium)
Fixing of Ceiling fan including transportation and giving connections with twin core wire etc., complete.
Fixing of given (9" to 24") Exhaust fan of in wall with necessary connections and masonry work of making hole, finishing etc., complete
Supply of 15" (375mm) ISI, 900 RPM Heavy duty exhaust fan with metallic blades with Mark. Makes: Crompton / Almounard / Havells Turbo Force / Halonix Krypton
Supply, Installation , Testing and commissioning of an all-in-one integrated LED solar street light consists of solar photovoltaic module, battery, battery management system, control electronics, LED driver, inter-connecting cables and pole mounting piece integrated into the luminaire as a single unit and with the following specifications:
A. LUMINAIRE The luminaire shall have highly efficient mid power white LEDs with lumen output in the range of 2800~3000 Lumens at system level & wattage should not be more than 15~20W with a typical correlated color temperature of 5700K with CRI>70 and lenses with efficient bat wing optics designed for efficient light distribution for secondary roads. Life will be 50000 Burning hours life class. The Successful bidder shall submit LM 79 & LM 80 of the Fitting and LED. Luminaire RAL 7011 with OEM Name Embossment is mandatory to ensure quality parameters met such as Single Piece High Pressure Die Cast. A switch shall be provided on the housing to disable the luminaire when required. The Luminaire shall meet the relevant IEC codes as mentioned in Table 1. Product should always deliver fixed output of 2800~3000 lumens at system level during complete autonomy period.
B. INTEGRATED CHARGE CONTROLLER: The luminaire shall have a highly efficient, integrated microprocessor based MPPT charge controller with driver mounted on the same board to minimize power loss. This intelligent power management system shall maximize the overall system efficacy to Minimum 175 lumens/watt with LM79 Report from Any NABL Accredited lab. The Controller Efficiency shall be > than 90% and shall have the
following inbuilt protection features: Ø Protection against battery overcharge and deep discharge condition. Ø Protection should be provided against battery and Panel reverse polarity. Ø Over current protection. Ø Protection for reverse flow of current through the PV module(s) should be provided. Ø ON/OFF switch to be provided to prevent discharge of battery during storage / before Installation Ø The Controller shall meet the relevant IEC codes mentioned in the table-I.
C. SOLAR MODULE : The Solar Cell shall be made of Premium grade mono crystalline silicon Cell. The Solar Module Power (Wp) shall be minimum 3.5 times the power consumption of LED Streetlight. The Solar Module Construction shall be of Low iron tempered glass with low reflection characteristics and with rated IP 65. The Life Cycle shall be > than 25 Years. The Solar module shall meet the relevant IEC codes mentioned in Table-I.
D. BATTERY : The Battery shall be Rechargeable Lithium Ferro Phosphate (LiFePo4) Battery Pack with rating (AH) minimum 1.75 times the power consumption of LED Streetlight. The Battery Pack should have Inbuilt Battery management system Module with following safety features Ø Accidental short circuit Ø Over discharge Ø Over charge Ø Over temperature. Ø Low Temperature The Life Cycle shall be Minimum 2000 Cycles for 90% daily depth Discharge. The Battery shall meet the relevant Compliance Standards mentioned in table-I.
E. HOUSING : The luminaire shall have single piece pressure die cast LM6 aluminum housing with Proper OEM Brand Name Embossment for ensuring quality & ruggedness and excellent heat dissipation with IP 65 protection and IK08 impact resistance. The front cover is composed of weather resistant, UV stabilized polycarbonate. The front cover is tightly secured with the housing to ensure that the luminaire has an ingress protection of IP65. The luminaire shall have a smart self-diagnosis feature with LED indicators for battery charging, deep discharge and Load cut off indication visible from ground in day light. Additionally, it should also be possible to monitor Current and voltages of Solar panel and Battery for diagnostic purposes through the mobile app. Test Certificate from Any NABL Lab is required.
F. Mounting Bracket : The luminaire shall have a specially designed pole mounting piece that enables lateral as well as post top mounting and installation at varying tilts from 0 to 15 degrees for optimal light distribution. It shall be suitable for mounting on pole of diameter 48 – 60mm.
Make: Philips / Jaquar / Equivalent in TTD approved brands Model:BRP710/LSRTSLRA1020 XC
Supply and fixing of 4 Way TP & N Horizontal type Distribution board as per IS 8623; IS 13032; IEC 61439-3 with IP-43 protection (Metal door) firmly concealed in the wall with neat plastering etc., complete.
Grade-A: Make: Legrand (Ekinox 3) / Schneider-Acti9 / Hager - Novello+ / Seimens / Havells STADx / L&T-Newrang / Indoasian (Opti Pro)
Supply and fixing of 20 Amps 2 Pin & Earth Socket Metal Plug Board with 1 No. 20 Amps SP MCB 10KA 'C' series ISI mark including the cost of MCB Concealed in the wall with neat plastering and giving necessary connections.
Grade-B: Make: ABB / Standard / Havells-euro II / C&S / L&T / GM / Gold Medal / Indo Asian
Supply and fixing of 63 Amp FP Isolator as per IEC:60947 Part-III in the existing board and giving necessary connections.
Grade-B Makes: ABB / Standard / Havells - Euro II / C&S / L&T / GM / Gold Medal / Hager / Indo Asian
Supply and fixing of 6 to 32 Amps range SP MCBs 10 KA breaking capacity 'C'/ 'D' Curve ISI mark as per IS:60898-1 : 2002 in the existing board and giving necessary connections.
Grade-B Makes: ABB / Standard / Havells-euro II / C&S / L&T / GM / Gold Medal / Hager / Indo Asian
Supply and erection of 4 Mts. long 2'' ( 50mm) dia GI pipe 'B' class after excavating an earth pit of size 2'x2'x3' and filled with sand to a height of 6" in the pit and concreting with C.C.1:3:6 with 1 1/2'' (40mm) HBG Crushed metal for full width to a height of 2 ½' over sand bed and coping should be done to a height of 2½' with square / round / hexagonal shape with 20mm HBG Metal in C.C. 1: 3 : 6 and plastering with 12mm thick in C.M. 1: 5. An MS box of size 12''x8''x6'' with screwing / hinges arrangement is to be fixed to the pole above the pole coping with 6mm thick hylum sheet fixed with brass bolts, nuts and washers etc and fixing of 1 No. of 16 Amp fuse unit in side the box. 2 wire run of 36/0.3mm PVC insulated FRLS copper cable from MS box at bottom to the top of the pipe and giving necessary connections to the fuse unit and to post top lantern fitting etc., The post top lantern fitting is to be fixed on the top of the pipe with suitable GI reducer and GI pipe wherever necessary. Painting should be done with two coats of enamel paint to the GI pipe and to the MS box over one coat of red oxide as directed during execution. (Post top lantern fitting will be supplied by departmentally)
Supply & fixing of 1" dia 'B' class GI pipe not exceeding 1.5Mtr long with necessary bending (120° to 135°) to the wall or to the pole as directed during execution duly grouting 2 Nos. of MS angle of 35x35x5mm having length 20Cm (grouted portion of MS angles into the wall 7.5cm) and fixing with 2 Nos. of MS clamps fabricated with 25mmx3mm MS flat with suitable holes and 4 Nos. of 3/8"x2" MS bolts, nuts & washers for fixing on the wall / 2 Nos. of suitable MS clamps with bolts, nuts for fixing to the pole etc., complete. A 16Amp fuse unit is to be fixed to the MS angle / clamp and giving necessary connections with 14/0.3mm PVC copper flexible wire from pole to the fuse unit and to the fitting or from Ceiling rose in the building to the fuse unit and to the fitting with link clips etc., and the GI pipe has to be painted with two coats of enamel grey paint over one coat of red oxide paint. Fixing charges for stem pipe including the cost of MS angle, MS clamps, bending of pipe, bolts, nuts, fuse units etc.
Supply and transportation of 16 Sq.mm 4 core LT XLPE insulated, 1100V grade armoured Aluminium UG cable as per specification confirming to IS:7098 (Part-I) / 1554-1. Grade-B: Make: RPG / Fortune Art / Delton / Orbit.
Supply Laying and Transportation of Outer dia 50mm and inner dia 38mm, 6Kg/Sq.Cm (PE- 100 grade) double walled corrugated HDPE duct made as per specification BSEN - 500 86/IS 14930 Part-II. Make : DURA LINE (Dura Guard) or its equivalent make.
Supply of 50 mm dia G.I. pipes of "B" class of ISI marked and approved by the department including cost and conveyance and all other incidental charges etc., and properties and weight as per IS 1239 marked . Make: Jindal / Appollo / TATA.
Supply and fixing of LT cable route indicators made out of cast iron fixed to one meter long 1''x1''x1/4'' MS angle 4'' bent at one end buried in the ground and the other end fixed with G.I. bolts and nuts to the cable route indicators as directed during execution.
Laying of U.G cables upto 50 Sq. mm with sand cushion covering the cable with bricks and back filling of Trench including cost and conveyance of materials and labour charges etc., complete.
Laying of U.G cables up to 50 Sq.mm through existing G.I.Pipe and back filling of trench including labour charges etc., complete. (Excluding the cost of G.I Pipe)
Supply and fixing of 4.5''x4.5'' with 3 mm thick laminated sheet of I.S.I Mark white or approved colour suitable for existing Concealed T.W. Board with brass screws, cup washers etc., complete.
Supply and fixing of 8.5''x6.5'' with 3 mm thick laminated sheet of I.S.I Mark white or approved colour suitable for existing Concealed T.W. Board with brass screws, cup washers etc., complete.
Supply and fixing of 12 Module Hot Dip Galvanized 20 / 18 SWG Module box with earthing terminal and vertical Cover plate & Frame and concealed in wall with all required accessories including masonry work and all labour charges etc., complete.
Metal boxes Make : Legrand / G.M / L&T / GM Four-Five / Legrand Arteor / Schneider / Anchor / Clipsal / Havells / ABB / Indo Asian / Siemen / Fortune Art. Cover plate & Frame Make Grade-B : Legrand Myrius / Crabtree Thames Platinum / Anchor Roma / Clipsal / Havells Coral or Fabio / Goldmedal (Curve/Air) / Schneider Livia / C&S / L&T / HPL / Kolors / Indo Asian / GM (GNINE)
Supply and fixing of 6 Module Hot Dip Galvanized 20 / 18 SWG Module box with earthing terminal and Cover plate & Frame and concealed in wall with all required accessories including masonry work and all labour charges etc., complete.
Metal boxes Make : Legrand / G.M / L&T / GM Four-Five / Legrand Arteor / Schneider / Anchor / Clipsal / Havells / ABB / Indo Asian / Siemen / Fortune Art. Cover plate & Frame Make Grade-B : Legrand Myrius / Crabtree Thames Platinum / Anchor Roma / Clipsal / Havells Coral or Fabio / Goldmedal (Curve/Air) / Schneider Livia / C&S / L&T / HPL / Kolors / Indo Asian / GM (GNINE).
Providing of Independent Chemical Earthing after excavating an earth pit of size1.5 m X 0.9 m X 2.05 m(Top 1.50 m X 0.90 m X 0.9m & bottom 1.20 m X 0.90 m X 1.15 m) with the following specification:-
(a) The Earth Electrodes, 40mm dia, wall thickness 3.25 mm, terminal Size 25x8 mm, terminal hole dia 12 mm, 2 meter long, galvanized, including 1 bag (25Kg to a bag) of Earth Life Compound, as per IS 3043, Base Metal: IS marked branded mild steel pipes.
Makes: Potential / Shake Hands / Mars / Tirumala / Arshlok earthing.
b) The Earth Electrode shall be inserted into the ground for 1.75 Mtrs. Below the inspection chamber bottom 300mm all around this Earth Electrode shall be covered with 25 Kgs. Of Earth Life Compound
(c) The excavated gap shall be back filled with excavated earth, and shall be properly consolidated with water.
(d) The top 0.25 m of Earth pipe shall be exposed into inspection chamber of Hume pipe . The all around inspection chamber shall be provided with 18" dia hume pipe. Earth connections shall be given to the Earth Electrodes with bolts, nuts & washers.
(e) A 65 mm dia PVC conduit is to be embedded through hume pipe at one side, to lay the Earth from the Earth bus to the Electrode through the PVC conduit and after laying the Earth, the pit entry PVC conduit is to be sealed with Bitumen compound.
(f) Necessary Meggar testing is to be done in the presence of the concerned Engineers, and the reading should be as per IE standards.
Supply and run of 25 mm X 3 mm G.I Strip for earth electrode to required places by concealing in walls, flooring by cutting the grooves and replastering neatly and giving necessary connection with 3/8"x2" GI Bolts, Nuts and Washers wherever joints has to be done. The strip has to be either riveted (or) bolted (or) gas welding neatly and all labour charges etc., complete.
Earth Work excavation for trench for laying of U.G. Cable in ordinary Soils, manual means to the required width and depth and depositing the same on bank as directed during execution etc., complete .
Screen painting on the new existing tube light fittings, ceiling fans, Heaters, AC units etc. indicating TTDs area, location, No.. The size of the letter should be minimum 25 mm. The work will have to be done at site.
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
RAW_HTML
48-BOQ.xlsx
TENDER_DOCUMENT • 0.03 MB
48 NIT.doc
TENDER_DOCUMENT • 0.79 MB
Download all tender documents and submit your bid