CWE/AF AMB/HAL-19/2022-23 SPECIAL REPAIRS TO CERTAIN SMQS IN NP AREA AT AF STN HALWARA UNDER GE (AF) HALWARA

Amount

Taking down cement plaster on brick or stone walls, etc including racking out joints, hacking for key, scrubbing down with water including removal of debries to distance not exceeding 500 mtr complete all as specified & directed.

Demolition of brick work or stone/boulder masonary built in cement mortar including all quoins, pillars etc but excluding ashlar facings, dressed stone work and precast articles complete all as specified & directed.

M&L Brick work with sub class B, burnt clay bricks of old size, designation 75, straight or curved on plan exceeding 6 mtr mean radius, built in cement mortar 1:6 complete all as specified & directed.

M&L rendering 15 mm thick in cement mortar 1:6, finished even and smooth without using extra cement on fair faces of brick or concrete surfaces as in wall complete all as specified & directed.

M&L preparation of newly plastered surfaces of wall and applying two coats of distemper oil emulsion(1st quality) of approved shade/tint over & including one coat of alkali resistant primer complete all as specified & directed.

Complete removal of existing treatment from old decorated plastered / unplastered surfaces of wall and applying two coats of distemper oil emulsion(1st quality) of approved shade/tint over & including one coat of alkali resistant primer complete all as specified & directed.

M&L rendering in two coats, 1st coat of 10mm thick in cement mortar 1:6 on fair faces of brick or concrete surfaces as in wall & 2nd coat of 5mm thick rendering in cement mortar 1:4 mixed with integral water proofing compound as per manufacturer's instruction finished even and smooth without using extra cement complete all as specified & directed. Notes: (i) Integral water proofing compound shall be measured & paid seperately. (ii) Two coat of rendering as specified above shall measured as one unit.

M&L preparation of newly plastered surfaces of wall and applying applying two coat of cement base paint of approved shade/tint complete all as specified & directed.

Complete removal of existing treatment from old decorated plastered / unplastered surfaces of wall and applying two coat of cement base paint of approved shade / tint complete all as specified & directed.

M&L rendering 5 mm thick in cement mortar 1:3, finished even and smooth without using extra cement on fair faces of concrete surfaces as in ceiling/soffits complete all as specified & directed.

M&L preparation of newly plastered surfaces of ceiling/soffits and applying three coat of white wash complete all as specified & directed.

M&L preparation of old treated plastered/unplastered surfaces of ceiling/soffits by brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of white wash complete all as specified & directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding but not backing, rubbish off the premises including removal of debries to distance not exceeding 500 mtr complete all as specified & directed.

M&L jointfee glazed ceramic coloured tiles, 1st quality, size 300mm X450mm, 7mm to 8mm thick on vertical surface as in skirting/dado, set and jointed in neat cement slurry & pointed in white or coloured cement to match the surface over & including 10mm thick rendering/backing coat in cement mortar 1:4 complete all as specified & directed.

M&L coloured, non-skid, jointfree, ceramic tiles, 1st quality, 7 to 8 mm thick, square/ rectangular, area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface over & including 15mm thick screed bed or bedding layers in cement mortar 1:4, complete all as specified & directed. Note:The Water Proofing Compound shall be mixed @ 3% by weight of cement in screed bed of first floor & above of bldgs. The WPC shall be measured & paid separately.

M&L coloured, non-skid, jointfree, ceramic tiles, 1st quality, 7 to 8 mm thick, square/ rectangular, area of each tile exceeding 0.18 Sqm but not exceeding 0.36 Sqm as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface over & including 15mm thick screed bed or bedding layers in cement mortar 1:4, complete all as specified & directed.

Taking down chowkhats or frames exceeding 1.50sqm each but not exceeding 4.0sqm each with shutters (without taking off shutter from frames) removing from site including cutting holes for taking out hold fasts and making good disturbed portion in cement mortar 1:3, complete all as specified & directed

Description all as per BOQ item No 17.00 here-in-above but chowkhats or frames not exceeding 1.50sqm each.

Taking down & refixing of shutter any description area exceeding 1 sqm but not exceeding 2 sqm each in the same/other opening complete all as specified & directed. Note: Taking down & refixing of each leaf of shutter shall be measured as one unit.

S&F second class hardwood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified & directed.

S&F pressed steel door frames (made out of cold rolled mild steel sheet 1.25mm thick), size 125mm x 60mm with one or more rebates including fixing necessary lugs, 3 Nos 100 mm long hinges per shutter, lock strike plate etc. including making good the disturbed portion to match with existing complete all as specified & directed.

S&F pressed steel door frames (made out of cold rolled mild steel sheet 1.25mm thick), size 105mm x 60mm with one or more rebates including fixing necessary lugs, 3 Nos 100 mm long hinges per shutter, lock strike plate etc. including making good the disturbed portion to match with existing complete all as specified & directed.

S&F mild steel work as in bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified & directed.

M&L plain cement concrete (PCC), 1:3:6 type C-1, using 20mm graded mechanically crushed stone aggregate as in hold fasts, filling of pressed steel frame etc. complete all as specified & directed.

S&F ECCO-400 Series window/ventilators (Double rebated) fabricated from rolled framed sections made of galvanized steel colour coated/powder coated (Base steel as per IS 513, "D" quality galvanised as per IS 277 with Zinc of 120gram/Sqm) with total coated thickness of 0.6mm and section of frame should be of 72mm x 55mm, section for mullion should be of 72mm x 50mm, section for shutter frame should be of 47mm x 20mm, section for fixed glass bead should be of 12mm x 12mm and section for flyproof mesh should be of 40mm x 20mm, coated section should be with primer coat of Epoxy primer of 5 to 7 microns thick, finish painted with polyester upto 50 to 60 microns thick including 5mm thick plain glass, stainless steel 32 gauge flyproof mesh of 304 grades with 144 holes per square inch and grill made of 10mm square MS bars welded to at 150mm center to center, 6mm x 12mm MS flat (total grill unit should be power coated and fixed to window frame with screws) complete as mentioned below and all as specifed & directed. (a) FIXING DETAILS :- Section for frame Glazed shutter and Mesh shutters should be cut to length and mitre joined with polyropylene corner brackets, mullion section should be joined with Frame /Mullion using Mullion Cap ethylproplene damein monomer (EPDM) gasket should be used all around glass in shutter and fixing glass rubber, Gasket should be around glass in shutter and fixed glass. rubber gasket should be used around fly mesh to fix mesh in mesh shutter.

(b) ACCESSORIES :- Each glazed shutter and mesh shutter should be provided with SS pivot hinges- 1 set, seccolor stay. window frame should be fixed to brick/concrete masonary by using Nylon self expanding caps and driving MS electroplated 80mm long screw into the caps through frame. Notes: - (i) Glazing, Wire mesh, Grill & Painting included in quoted rates. (ii)Double shutter meant for providing glazed shutter as well as wire gauged shutter on outside & inside of the frame respectively. Both the shutters shall be measured as one unit.

S&F factory made second class, hard wood(hollock), plain, framed, panelled shutters 35mm thick (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003(Part I), kiln seasoned and chemically pressure treated complete all as specified & directed.

S&F factory made second class, hard wood(hollock), glazed and skeleton shutter, 35mm thick, open rebated and prepared to receive glass/guage etc, without sash bars, with edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass/guage etc, sizes of members of shutters as specified in Section 8, clause 8.24(a) of SSR part-I supplied & fitted to chowkhats complete all as specified & directed.

S&F factory made, solid PVC Door Frame of size 50mm x 47mm made out of 5mm thick single side prelaminated PVC sheet reinforced with mild steel square tube, edges will be painted to match with prelaminated sheet fixed in opening as per specification & drawing given in SSR Part–II complete all as specified & directed.

S&F factory made, solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of mild steel tubes for top & bottom rails. Mild steel frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and single side prelaminated PVC sheet for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of single side prelaminated PVC sheet to be fitted in the mild steel frame welded / sealed to the stiles & rails having one side feathered edge and on other side 10mm 90 degree bent edge, suppling & fixing in the frame at site as per drawing given in MES SSR Part –II complete all as specified & directed.

S&F 25mm thick flush shutter, factory made, solid core construction with block board core and plywood face panels commercial type on both side with decorative face veneer on both side with lipping/frame to match complete all as specified & directed.

S&F 125mm hasp and staple, safety type, anodized aluminium with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified & directed

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm fixed with tinned tacks or stainless steel wire staples complete all as specified & directed.

S&F in repair stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm fixed with tinned tacks or stainless steel wire staples complete all as specified & directed.

S&F 100 mm size, MS butt hinges, medium weight, cold rolled, fixed complete all as specified & directed

S&F 75 mm size, MS butt hinges, medium weight, cold rolled, fixed complete all as specified & directed

S&F 50 mm size, MS butt hinges, medium weight, cold rolled, fixed complete all as specified & directed

S&F second class hardwood small fittings such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including all necessary labours; articles not exceeding 200 cubic centimetre each complete all as specified & directed.

S&F 150 mm length of cover plate, floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor with vulcanised rubber piece complete all as specified & directed.

S&F in repair 150 mm length of cover plate, floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor with vulcanised rubber piece complete all as specified & directed.

S&F 200mm long, aluminium, anodized, barrel tower bolt of extruded section complete all as specified & directed

S&F 150 mm size Aluminium handle, cast type, anodized fixed complete all as specified & directed

S&F 250mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified & directed.

S&F MS Helical door spring 300 mm ordinary rat tail rod pattern including roller and roller plate complete all as specified & directed

M&L preparation of new wood and wood based surface of any description over 10cm width or girth and applying two coat of synthetic enamel paint over & including one coat of pink primer complete all as specified & directed.

M&L preparation of old painted or previously untreated wood and wood based surface of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified & directed.

Taking down or up steel tubing and connections for refixing or removal from site for 15 mm bore pipe complete all as specified & directed.

Taking down or up steel tubing and connections for refixing or removal from site for 20 mm bore pipe complete all as specified & directed.

Supply & laying 16mm outer dia CPVC pipes confirming to IS:15778, Standard Dimensional ratios (SDR) 11 and Plain CPVC Standard Dimensional ratios (SDR) 11 fittings on walls/ceiling or laying in floors complete all as specified & directed.

Description all as per BOQ item No 48.00 here-in-above but 20mm outer dia CPVC pipes.

S&F in repair 15mm bore bib tap (minimum weight 90 gram) standard of PTMT any colour high pressure screwed for iron pipe and fixed complete all as specified & directed

S&F in repair 15mm bore stop valve (minimum weight 90 gram) of PTMT any colour high pressure screwed for iron pipe and fixed complete all as specified & directed

S&F in repair 20mm bore stop valve (minimum weight 92 gram) of PTMT any colour high pressure screwed for iron pipe and fixed complete all as specified & directed

S&F in repair 15mm bore stop valve (minimum weight 110 gram) of PTMT any colour high pressure screwed for iron pipe and fixed with long shank and cup (concealed type) complete all as specified & directed

S&F in repair vitreous china squatting pan (Orissa pattern) 580mm x 440mm, white, with integral foot rests excluding flushing cistern and flush pipe including connection to trap, and to flushing pipe, anti-syphonage pipe, etc. complete including making good to floor complete all as specified & directed.

S&F in repair PVC connection 450mm long with 2 nos PTMT check nuts, suitable for 15mm bore complete all as specified & directed

S&F in replacement PVC low level flushing cistern, white, valveless syphonic action type 10 litre capacity with inlet, ball valve, float and handle including PVC flush pipe 32 mm dia with bend and a pair of mild steel angle iron brackets of suitable size including making necessary connections to water supply pipe line and WC, complete all as specified & directed.

S&F in replacement swivel shower of PTMT any colour for fixing with 15mm pipe (Minimum weight 40gram) complete all as specified & directed.

S&F in replacement vitreous china wash hand basin, flat back type, white, size 550mm x 400mm including 32mm bore PVC waste pipe of suitable length, CP waste fitting & one pair of mild steel angle iron brackets of suitable size fixed as in counter slab complete all as specified & directed.

S&F in replacement vitreous china wash hand basin, B corner type, white, size 450mm x 390mm including 32mm bore PVC waste pipe of suitable length, CP waste fitting & one pair of mild steel angle iron brackets of suitable size fixed as in counter slab complete all as specified & directed.

S&F in repair 15mm bore fancy type pillar taps (minimum weight 110 gram) of PTMT any colour high pressure screwed for iron pipe and fixed complete all as specified & directed.

S&F in repair chromium plated, brass, tubular towel rail with brass CP brackets on both sides, 20mm dia, D type, 600mm long between flanges , fixed with screws complete all as specified & directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified & directed.

S&F mild steel work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified & directed

S&F rolled mild steel work as in compound girders and stanchions, lattice girders, aerial masts, staging for water tanks and the like including caps, bases, splices etc. built up from two or more beam or channel sections or angles with plates, including all lattice bars, stiffeners, gusset plates, etc. conforming to Fe 410-W(Gde-E-250) Quality 'A' complete all as specified & directed

M&L preparation of new steel and iron based surface of any description over 10cm width or girth and applying two coats of synthetic enamel paint over & including one coat of red oxide primer complete all as specified & directed.

M&L preparation of old or previously treated steel and iron based surface of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified & directed.

Demolition of stone slabs and tiles of any description or thickness as in floors, aprons etc, laid, bedded & pointed in any mortar and rubbish off the premises to a distance not exceeding 500 mtr complete all as specified & directed.

M&L machine cut Granite stone slab/tiles, 16mm to 18mm thick, table rubbed and polished, as on shelves/ cooking platform/steps/pillars etc, like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite laid over & including 15mm thick screed bed or bedding layers in cement mortar 1:4, set and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified & directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified & directed.

M&L machine cut Kota stone slab 18 to 20mm thick as in flooring/stair case landing, laid over & including 15 mm thick screed bed in cement mortar 1:6, and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified & directed.

M&L machine cut Kota stone slab 18 to 20 mm thick as in skirting / dado, steps, laid over and including 10 mm thick rendering in cement mortar 1:4, and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified & directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified & directed.

S&F PVC (SWR) pipe 110mm bore, single socketed in any length with rubber ring joints, fixed to wall complete all as specified & directed.

S&F PVC (SWR) pipe 75mm bore, single socketed in any length with rubber ring joints, fixed to wall complete all as specified & directed.

S&F 110mm bore PVC (SWR) bends any radius complete all as specified & directed.

S&F 75mm bore PVC (SWR) bends any radius complete all as specified & directed.

S&F 110mm bore PVC (SWR) junction single, (single T), equal or unequal provided with acess door complete all as specified & directed.

S&F 75mm bore PVC (SWR) branch piece double, (double Y), equal or unequal provided with acess door complete all as specified & directed.

S&F 110mm bore PVC (SWR) vent cowl complete all as specified & directed.

S&F 75mm bore PVC (SWR) vent cowl complete all as specified & directed.

S&F in repair PVC (SWR) floor trap 75mm dia outlet with chromium plated grating, including jointing to waste pipe with solvent cement and embedded in cement concrete type B-0 (1:2:4) complete all as specified & directed.

Demolition of Plain cement concrete (un-reinforced) in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) including removal of debris to a distance not exceeding 500 mtr complete all as specified & directed

M&L 75mm thick PCC 1:3:6, type C-2, using 40mm graded mechanically crushed stone aggregate as in plinth protection finished even and smooth without using extra cement with & including 10mm wide, 30mm deep joints at the rate of 3.00 mtr centre to centre and at every turning & filling the joints with bitumen & sand mixture complete all as specified and directed. Notes :- (i) The unit rate quoted shall be deemed to include for providing the concrete in alternate bays not exceeding 3 Mtrs length. (ii) 30 mm deep joints between the bays shall be provided which shall be filled with mastic filling with hot bitumen 85/25 grade and 1:2 mix volume.

M&L 75mm thick PCC 1:4:8, type D2, using 40mm graded mechanically crushed stone aggregate as in sub bases of floors complete all as specified & directed.

M&L sand filling under floors or as in similar works including watering and consolidation complete all as specified & directed.

M&L 60mm thick, M-35 grade machine pressed precast concrete interlocking paver block any shape any size confirming to IS 15658-2006 with grey cement and pigment complete all as specified & directed. Note: Joints shall be filled with fine dry sand and included in quoted rates.

Demolition of Plain cement concrete (un-reinforced) in above ground floors and pavings exceeding 15cm thickness including removal of debris to a distance not exceeding 500 mtr complete all as specified & directed

M&L PCC 1:5:10, type E-2, using 40 mm graded mechanically crushed stone aggregates as in foundation, sub base (as in sunken floor) and mass concrete complete all as specified & directed.

M&L coating with two coats of water proofing chemical as per manufacturer's instructions by brush on the entire surface of sunken portion, 15mm thick screed bed/bedding layer in cement mortar 1:3 mixed with integral water proofing compound @ 130ml per bag of cement including one bonding coat of cement slurry mixed with water proofing chemical @ 200ml per bag of cement complete all as specified & directed. Notes: The water proofing chemical for coating, water proofing compound and water proofing chemical for cement slurry shall be of same make as given in appendix here-in-after. (ii) The work described as above shall be executed all as per directions of Engineer-in-charge and shall be measured as one unit. (iii) Security deposit as a guarantee against Water proofing treatment shall be retained in final bill and shall be released after 10 years. If contractor fail to rectify the defect pointed out during this period in writing, the defect shall be got rectified at contractor' risk and cost and the payment shall be made from the amount kept reserved or by encashing the FDR deposited by the contractor as guarantee.

Demolition of plain cement concrete (unreinforced) of any description and in any position not otherwise specifically provided including removal of debris to a distance not exceeding 500 mtr complete all as specified & directed

M&L PCC 1:2:4, type B-1, using 20 mm graded mechanically crushed stone aggregates as in roof kerbs or mud stops, rounded or chamfered angles and throating, as directed complete all as specified & directed. Note : The quoted rates include for use of formwork (straight or curved).

M&L brushing neat cement slurry @ 3.0 Kg per Sqm and cleaning the top surface using broom, wire brushes etc. & finally wahsing the surface complete all as specified & directed.

M&L averaging 40mm thick Plain Cement Concrete(PCC) 1:2:4, type B-0, using 12.5mm graded mechanically crushed stone aggregates over roof slab as in padding in slope to make good the depressions/undulations complete all as specified & directed.

M&L 10 mm thick plastering in cement mortar 1:4 on cleaned concrete surfaces, sides of parapet etc mixed with integral water proofing compound (WPC) as per manufacturer's instructions, finished even and fair complete all as specified & directed. Note : WPC shall be measured and paid separately.

Supply only integral water proofing compound (WPC) complete all as specified & directed.

M&L preparation of roof top surfaces, providing and applying UV stable single component fibre reinforced elastomeric liquid applied water proofing membrane formulated with PU hybrid polymers and reinforcing acrylics fibres and having Sun Reflectivity Index (SRI) of 106 on top of concrete roof surfaces in three coat including self primer mixed with water at ratio of 3:1 and coverage @ 1 Ltr per Sqm with a thickness of 650 micron, the vital physical and chemical parameters shall be as under : Min Elongation at break of 350%, Resists positive hydrostatic pressure of upto 10 bars, crack bridging ability of 2.5 mm at 650 microns. The material shall be applied with brush or roller, 6 Hrs interval between two coat will be maintained complete in all respect as per manufactrurer's instructions and as directed. Make : Smart Care Damp Proof Ultra of M/s Asian paint Ltd or equivalent in M/s IWL India Limited, M/s STP Limited, M/s Bostik India Pvt Ltd, M/s Maruti Bitumen Pvt Ltd, M/s Fosroc Chemicals

Notes for BOQ item No. 96.00 : (i) The water proofing treatment shall be got carried out by the manufacturer or their authorised applicators duly approved by GE in writing. (ii) Payment to contractor will be made only after receiving of the warranty certificate from the Manufacturer (iii) Security deposit as a guarantee against Water proofing treatment shall be retained in final bill and shall be released after 10 years. However contractor may deposit the FDR of same amount in favour of GE. If contractor fail to rectify the defect pointed out during this period in writing, the defect shall be got rectified at contractor' risk and cost and the payment shall be made from the amount kept reserved or by encashing the FDR deposited by the contractor as guarantee. (iv) The amount of security deposit shall be calculated as per the scales laid down for calculating Earnest Money Deposit enhanced by 25% on the total amount of Water proofing treatment work (BOQ item No 92.00 to 96.00). The contractor's quoted rates for these items shall deemed to be inclusive of this aspect.

Demolition of Reinforced cement concrete(RCC) of any description and in any position not otherwise specifically provided including cutting the reinforcement as required to facilitate demolition and removal of debris to a distance not exceeding 500 mtr complete all as specified & directed. Note: Steel obtained from demolition shall be credited to contractor.

M&L precast cement concrete type B-1, 1:2:4 (using 20mm graded mechanically crushed stone aggregate) as in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain fair faces, including chamfers, weatherings, throating etc. and setting in cement sand mortar of 1:4 complete with joints to match complete all as specified & directed. Notes: (i) The rates include for the use of forms, moulds or machine moulds and setting the blocks, slabs, etc. complete including raking back the joints of the internal faces (at least 10 mm) for pointing as the work proceeds or finishing with neat flush joints. (ii) Reinforcement shall be measured & paid separately.

M&L mild steel TMT bars, 10 mm dia and over, cut to length, bend to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified & directed.

M&L repairing RCC projection chajjas, roof, facia etc. by necessary preparation, scraping, cutting, chiseling derusting and cleaning exposed reinforcement surfaces of damaged, loose RCC surfaces with cement concrete (1:1.5:3) using 12.5mm graded crushed stone aggregates and reinforcement with welded wire mesh of weight exceeding 2.0Kg per Sqm but not exceeding 3.0Kg per Sqm (if required) with or without facia and finished with cement mortar 1:3 using coarse sand. Work shall be in patches of area not exceeding 5 Sqm and thickness RCC member not exceeding 70mm including necessary formwork and applying two coats of finishes to match with the existing surfaces at any height complete all as specified & directed. Notes: (i) Welded wire mesh included inquoted rates. (ii) Necessary scaffolding as required at site shall be provided by contrator without any extra cost and shall remove the same on completion of the work.

Dismantling boarding, any description, fixed in any position with screws complete all as specified & directed.

S&F 18/19mm thick prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work with 6mm lipping teak wood fixed with nails complete all as specified & directed.

S&F moulding section of IInd class hardwood, sectional area exceeding13 sqcm & not exceeding 25sqcm as in cornices, picture rails and the like fixed with screws complete all as specified & directed.

S&F 40mm flap width (opened width) continuous (piano) hinges, mild steel, bright finish or electrogalvanised complete all as specified & directed.

S&F Ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed complete all as specified & directed.

S&F 100mm size aluminium handle, cast type, anodized fixed complete all as specified & directed

M&L post constructional anti termite treatment of the soil along external perimetre of building below ground level or masonry apron at the rate of 2.25 litre of emulsion per metre of surface area including drilling and plugging holes etc. in apron complete all as specified & directed.

M&L post constructional anti termite treatment of the soil under existing floor using emulsion at the rate of one litre of emulsion per hole, 300 mm apart including drilling and plugging 12 mm dia hole with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floor complete all as specified & directed.

M&L post constructional anti termite treating at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre per hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same complete all as specified & directed. Note for BOQ item No. 107.00 to 109.00:- For Guarantee & Security deposit refer Particulars specifications.

S&F in replacement rotational moulded polyethylene(PVC) water storage tank, HDPE, off white colour, triple layered , cylinderical type fixed and hoisted in position on roof, at any height, of capacity 750 litre and making connections with 20 mm GI pipe inlets & outlets complete including locking arrangements and 20 mm bore ball brass valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 210 gram) complete all as specified & directed. Note: Ball brass valve of PTMT included in quoted rates.

S&F in replacement stainless steel plate rack made out of 1.00mm thick steel sheet(stainless steel of grade 304) of size 77cm x 90cm x 25cm with fixing arrangements complete all as specified & directed.

S&F in repair curtain harrison rails of anodised aluminium alloy with fixing brackets, stops, rollers etc. complete all as specified & directed.

S&F in replacement sink made of stainless steel 1.00 mm thick steel sheet(grade AISI 305), kitchen or laboratory with plug & chain, waste coupling, washers and 32 mm bore PVC waste pipe including bedding in cement mortar to dwarf wall or including fixing cantiliver MS brackets and connecting union to pipe, over all size 495mm x 420mm & bowl size 410mm x 330mm x 160mm complete all as specified & directed.

Excavation in trenches not exceeding 1.5mtr wide and not exceeding 1.5mtr in depth for foundation etc or for walls, shafts, manholes not exceeding 10 Sqm on plan or for laying pipes/cables etc and getting out, in any type of soil complete all as directed.

Returning filling in including spreading leveling watering and well ramming in layers not exceeding 25 cm thick each in any type of soil complete all as specified & directed.

Removal of excavated soil to a distance not exceeding 50 mtr & depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified & directed.

S&F 25mm bore gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed including taking down of existing old globe/gate valve any size complete all as specified & directed.

S&F in repair bib cock, 15 mm bore, cast copper alloy, brass chromium plated, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified & directed.

S&F galvanized iron water tubes 15 mm bore, medium grade, ISI marked with all fittings laid in trenches including taking down/out of old unserviceable GI pipe complete all as specified & directed.

S&F galvanized iron water tubes 20mm bore, medium grade, ISI marked with all fittings laid in trenches including taking down/out of old unserviceable GI pipe complete all as specified & directed.

S&F galvanized iron water tubes 25mm bore, medium grade, ISI marked with all fittings laid in trenches including taking down/out of old unserviceable GI pipe complete all as specified & directed.

S&F galvanized iron water tubes 40mm bore, medium grade, ISI marked with all fittings laid in trenches including taking down/out of old unserviceable GI pipe complete all as specified & directed. Note for BOQ item NO. 120.00 to 123.00: Excavation & earthwork shall be measured & paid seperately.

Drilling and tapping cast iron water mains (in position) for branch connections of the internal dia 20mm complete all as specified & directed.

S&F in replacement 15mm bore ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified & directed.

Taking down copper/aluminium point wiring (light, fan, bell, socket or power) including surface/concealed conduit or wooden batten & sunken boxes complete, including taking out/down of unserviceable fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, call bell, light fitting etc., taking credit and making good disturbed surfaces of walls/floors/ceilings complete all as specified & directed .

M&L concealed point wiring with Flame retardant low smoke(FRLS), PVC insulated unsheathed cable 1.5 sqmm with multistranded copper conductor, 1100 volt, drawn through in and including non metallic rigid PVC conduit not less than 20mm bore(having 2mm wall thickness), medium grade, with conduit fittings including all tees, bell mouth tube ends and fixing accessories such as couplers, saddles, pipe hooks etc concealed in wall/ceiling/roof etc with provision of new sunken type pressed steel/welded MS terminal boxes of not less than 1.6mm wall thickness(duly painted with two coat of anticorrosive paint outside & aluminium paint inside) with decorative laminated sheet top cover 2.8mm/3mm thick including Flame retardant low smoke(FRLS), PVC insulated, unsheathed, multistranded copper earth conductor 1.5 sqmm connected to common earth and earth dolly for one light point, ceiling fan/exhaust fan point controlled by one way switch 5/6 amp complete all as specified & directed.

Description all as per BOQ item No. 127.00 here-in-above but for one socket outlet point 5/6 amp controlled by one way switch on the same board.

Description all as per BOQ item No. 127.00 here-in-above but for one socket outlet point 5/6 amp controlled by one way switch on the independent board.

Description all as per BOQ item No. 127.00 here-in-above but for one call bell point controlled by one bell push on independent board.

Description all as per BOQ item No. 127.00 here-in-above but for one light point controlled by two way switch on independent board.

M&L concealed point wiring with Flame retardant low smoke(FRLS), PVC insulated unsheathed cable 4.0 sqmm with multistranded copper conductor, 1100 volt, drawn through in and including non metallic rigid PVC conduit not less than 25mm bore(having 2mm wall thickness), medium grade, with conduit fittings including all tees, bell mouth tube ends and fixing accessories such as couplers, saddles, pipe hooks etc concealed in wall/ceiling/roof etc with provision of new sunken type pressed steel/welded MS terminal boxes of not less than 1.6mm wall thickness(duly painted with two coat of anticorrosive paint outside & aluminium paint inside) with decorative laminated sheet top cover 2.8mm/3mm thick including Flame retardant low smoke(FRLS), PVC insulated, unsheathed, multistranded copper earth conductor 4.0 sqmm connected to common earth and earth dolly for one socket outlet point 15/16 amp controlled by one way switch on the independent board complete all as specified & directed. Notes for BOQ item No. 127.00 to 132.00 :- (i) S&F of Switches, socket outlets, bell pushes and fan regulators etc. shall be measured and paid for separately. (ii) Rate quoted shall be inclusive of cutting chases in wall and making good in cement mortar 1:3 & finishing the disturbed surfaces to match with the existing surfaces.

S&F switch piano, flush type, 5/6 amp, single pole, one way complete all as specified & directed.

S&F switch piano, flush type, 5/6 amp, single pole, two way complete all as specified & directed.

S&F bell push, flush type, 5/6 amp complete all as specified & directed.

S&F socket outlet, flush type, 2 in 1, 3 pin, 5/6 amp, complete all as specified & directed.

S&F switch piano, flush type, 15/16 amp, single pole, one way complete all as specified & directed.

S&F socket outlet, flush type, 2 in 1, 3 pin, 5/6 & 15/16 amp, complete all as specified & directed.

S&F stepped type electronic fan regulator flush type, single pole 240 volts, 50 Hz, 4 step type, 100 watts, on the existing phenolic laminated sheet etc. as required complete all as specified & directed.

S&F ceiling rose, surface bakelite 3 terminals, isolated body complete all as specified & directed.

S&F lamp holder PVC/Polycarbonate insulated body with back plate suitable for angle/batten fitting complete all as specified & directed.

S&F retrofit LED bulb 9 watt, pin type, colour white light complete all as specified & directed.

S&F in replacement LED tube light fitting 1x20 watt, four feet long, 220Volt AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.complete all as specified & directed.

S&F in replacement LED light fitting mirror type with high output diffuser 2 feet, 10 watt 220 Volt AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified & directed.

S&F in replacement LED light fitting 1x10Watt bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified & directed. Note for BOQ item No. 143.00 to 145.00: LED fittings should be of Power factor >0.95, THD < 10% & Lux 100 Lum/watt

M&L in replacement concealed sub main wiring with two single core FRLS, PVC insulated, unsheathed cable,1100 volts grade, 6 sqmm nominal cross sectional area stranded copper conductor and one single core green FRLS, PVC insulated, unsheathed 6 sqmm stranded copper conductor as earth continuity cable drawn through in & including non metallic rigid PVC conduit medium grade not less than 25mm bore including accessories concealed in wall/floors/roof etc including cutting chases in wall/ceiling and making good the disturbed surfaces to match with existing surface complete all as specified & directed. Note :- Two runs of 6 sqmm cable alongwith one run of 6 sqmm cable as earth wire alongwith conduit shall be measured as one unit. The cost of cutting of chases wherever required shall deemed to included in quoted rates.

S&F in replacement sheet metal enclosure for MCB DBs, 230 volt, single pole and neutral, distrubution board, IP 43 protection, with 200 Amps rated copper bus bar and neutral link, 8 way, double door type flushed inside the wall including making good the disturbed surfaces complete all as specified & directed.

S&F in replacement MCB, single pole & neutral, 40 Amp, B curve, 10 kA capacity, 240 volts complete all as specified & directed.

S&F in replacement MCB, single pole, 5 to 32 Amp, B curve, 10 kA capacity, 240 volts complete all as specified & directed.

S&F call bell, ding dong type, 230 Volts, single phase complete all as specified & directed.

Taking down carefully existing ceiling fan or Exhaust fan any size / sweep and deposit to MES storeyard and re-hanging/re-fixing the same including transport and connecting the fan with 2 core flexible copper cable 23/0.0076 of required length connecting with ceiling rose alongwith mild steel sheet 1mm thick louver shutter of suitable size compete all as specified & directed.

S&F building security light fitting 35 Watt LED New generation Enrgy Saving & Environment friendly long life versatile pressure die-cast aluminium IP-66 roadway luminaries with high power LEDs as light source and electronic drive including fixing arrangment on wall with security light mounting bracket, GI pipe of suitable size medium grade for mounting bracket bent to shape upto 1.50 meter length and fixing arrangement with two Nos. of MS clamps set, nut, bolts, washers, and applying two coats of aluminium paints over & including one coat of Zinc oxide primer complete all as specified & directed. Note: The GI pipe as in bracket is included in quoted rates. LED fittings should be of Power factor >0.95, THD < 10% & Lux 100 Lum/watt

Supply, laying, jointing, testing and commissioning LT XLPE insulated, armoured, heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 25sqmm, 3.5 core conforming to IS- 7098 (Part I) 1988 (with upto date amendments) as in trenches or along the wall/pole through pipe etc, including taking down/out of old existing LT cable complete all as specified and directed. Note:- Excavation & earth work, sand cushioning, protection pipes, end termination joints & protection covers shall be measured and paid separately.

M&L Sand cushioning to cable with a layer of dry fine sand 8 cm deep before laying the cable and 15 cm deep after laying the cable (punned down to 18 cm depth after laying and stretching of cable ) complete all as specified & directed.

Supply and laying old size, common burnt clay, sub class 'B' bricks, designation 75, laid flat & dry for protection of cable , adjacent to each other, perpendicular to central axis of cable complete all as specified & directed.

S&F GI tubing 40mm bore light grade with all fitting for calbe protection fixed to wall , pole or laid in trenches & road crossing and making good disturbed surface complete all as spefcified & directed.

Supply, installation, commissioning and testing in replacement polycarbonate CPRI approved OEM made meter panel (size 0.9mtr x 0.9mtr x 0.17mtr). The panel shall be made of modular Polycarbonate Thermoplastic Enclosures which should be UV resistance in accordance with IEC 61439-1, clause 10.2.4. Meter panel type wall mounted type structure RAL 7016. The meter panel should be anti-acid, anti corrosive & fully transparent door for meter vision. Degree of protection against mechanical load should be IK08 (5 Joule) in accordance with IEC 62262. The manufacturer of panel shall submit a copy of CPRI test report in Polycarbonate only also share panel assemble by OEM. Channel partner or sister concerned assembly will not accepted. Degree of Ingress protection IP 65 in accordance with IEC 60529. The gasket should be internally embedded made of polyurethane. The manufacturer of panel shall submit a copy of Type Test Report of a board made out of Polycorbonate Thermoplastic panel in accordance with IEC 60439-1. The CPRI report shall have mention of following tests performed and passed out satisfactorily:- Temperature rise, dielecric properties, short circuit withstand current- Rated peak & short time withstand current and rated conditional short circuit current, Effectiveness of protective circuits. The board manufacturer must submit the copy of type test reports for Polycarbonate Thermoplastic board only.

Test reports submitted of other material of construction like MS, SS will not be applicable. Each Board shall have individual routine test report of the manufacturer. The panel should passed glow wire test 960 degree centigrade in accordance with 60695-2-11 (Flame retardant and self-exinguishing). One main incomer MCCB 100A TP 25 KA Thermal/Magnetic release with spreader link. MCCB/MCB Nob shall be operated by flip cover, indicator provided on each phase. Provision of new four Nos. single phase meter. Output supply by MCB DP 32 Amp 4 Nos. meter Enclosures & enclosures accessories as per RAL 7035. Ten Nos terminal blocks provided for output supply. Make: Hensel, Rittal, Emitter, Schneider Note: Old unserviceable meter panel shall be deposited to MES store yard with proper documentation.

M&L earthing complete with galvanized steel earth plate electrode 60cm X 60cm X 6mm thick buried vertically in ground to depth not less than 2.25 mtr below ground level, with top edge of earth plate not less than 1.5 mtr below ground level surrounded from all sides by 15cm thick packed layer of Charcoal dust & common salt filled in alternate layers and electrode connected to GI earth lead strip 32mm x 6mm upto 7.5mtr long by means of bolts, nuts, check nuts and washers of galvanized iron and connection to earthing test point & earth dolly & watering pipe medium grade GI 20 mm bore including protection pipe GI light grade 40mm bore, including wire mesh, funnel, lugs, salt, charcoal dust, excavation in any type of soil, returning filling & removal of surplus soil upto 50mtr, pit chamber shall be of PCC 1:3:6 type C-1 using 20 mm graded mechnically crushed stone aggregates and pit cover slab 50mm thick shall be of Precast RCC 1:2:4 type B-1 using 20 mm graded mechnically crushed stone aggregates reinforced with welded steel wire fabric or XPM weighing not less than 4Kg/sqm with cast iron frame including necessary form work complete all as shown in electrical plate No 3 of SSR part-I, including testing on completion at site complete all as specified & directed. Note:- Any variation in length of earth lead and protection pipe of earth lead shall be adjusted through DO. On testing if the desired earth resistance is not obtained, earthing will be generated at No extra cost, till the desired earth resistance is obtained. The chamber shall be constructed atleast 1.5 mtr away from the earth electrode.

For Credit Schedule refer tender documents. The amount of credit schedule shall be deducted in total quoted amount of BOQ to arrive contract sum.

JINDAL AND COMPANY

M/s R.N Construction Co.