ADDITION / ALTERATION INCLUDING SPECIAL REPAIRS TO BLDG NO. P-15 AT NPOL, KOCHI

Amount

Demolition of concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level), complete all as specified and directed.

Demolition of concrete in ground floors and pavings n exc 15 cm thickness above ground level, complete all as specified and directed.

Taking down cement plaster any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water etc., to receive plaster, complete all as specified and directed.

Rendering 10mm thick in CM (1:6) on fair faces of brick work or concrete surfaces, finished fair and even without using extra cement, complete all as specified and directed.

Rendering 10mm thick in CM (1:3) on other than fair faces of brick work or concrete surfaces, for fixing tiles on vertical surfaces, complete all as specified and directed.

Rendering 15mm thick in CM (1:4) on other than fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement, complete all as specified and directed.

Complete removal of existing treatment on wall surfaces and applying two coats of acrylic emulsion distemper, white or tinted over a coat of primer over and including 2.0mm thick interior grade wall care putty, finished even and smooth, complete all as specified and directed.

Applying two coats of acrylic emulsion distemper, on newly plastered wall surfaces, white or tinted over a coat of primer over and including 2.0mm thick interior grade wall care putty, finished even and smooth, complete all as specified and directed.

Preparation of old plastered surfaces of ceilings and applying one coat of white wash, complete all as specified and directed.

Complete removal of existing treatment on wall surfaces and applying two coats of weather-proof antifungal exterior emulsion paint, first quality, over a coat of primer all as per manufactureres instructions, complete all as specified and directed.

Applying two coats of weather-proof antifungal exterior emulsion paint, first quality, on newly plastered wall surfaces over a coat of primer all as per manufactureres instructions, complete all as specified and directed.

Plain cement concrete (1:2:4) type B0 (using12.50mm graded stone aggregate) 25mm thick as in sub base for laying floor finishes, complete all as specified and directed.

Screed bed or bedding layer of mortar 15 mm thick in CM (1:4) for laying floor finishes, complete all as specified and directed.

Non-skid ceramic coloured joint free tiles of size 400 x 400 x 8 to 9 mm thick (Minimum) (B-II a / B-II b Grade), as in floors etc., set and jointed in neat cement slurry and pointed in epoxy grout to match, complete all as specified and directed.

Non-skid ceramic coloured joint free tiles of size 600 x 600 x 8 to 9 mm thick (Minimum) (B-II a / B-II b Grade), as in floors etc., set and jointed in neat cement slurry and pointed in epoxy grout to match, complete all as specified and directed.

Non-skid ceramic coloured joint free tiles of size 600 x 600 x 8 to 9 mm thick (Minimum) (B-II a / B-II b Grade), as in vertical surfaces like skirting etc., set and jointed in neat cement slurry and pointed in epoxy grout to match, complete all as specified and directed.

Machine cut kota stone slab of size 550 x 550 x 22-25mm thick as in flooring over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, complete all as specified and directed. Note: - Kota stone edges shall be fine cut and matched at site at joints)

Machine cut kota stone slab of 22-25mm thick as in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, complete all as specified and directed.

Glazed ceramic tiles of size 600 mm x 300 mm x 7 mm thick (B-III a Grade), in vertical surfaces such as skirtings / dado etc., set and jointed in neat cement slurry and pointed in epoxy grout to match, complete all as specified and directed.

Granite (of any type) (of shade block galaxy) work (table rubbed and polished), 25mm thick as in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, complete all as specified and directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations, complete all as specified and directed.

Treatment along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron, complete all as specified and directed.

Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors, complete all as specified and directed.

Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area, complete all as specified and directed.

Treating at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same, complete all as specified and directed.

Taking down chowkats or frames not exceeding 1.5sq.m each (without taking off shutters from the frames), complete all as specified and directed.

Taking down chowkats or frames exceeding 1.5sq.m not exceeding 4sq.m each (without taking off shutters from the frames), complete all as specified and directed.

Second class hard wood, plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed, complete all as specified and directed.

Second class hard wood plain, framed, panelled shutters (two number of panels), 35mm thick, factory made, with lock rail and panels of 9mm thick BWP commerical ply or 12mm thick veneered particle board medium density with commercial veneering on both faces : supplied and fitted to chowkats; The size of rail and styles shall be all as per IS : 1003 (Part - I), kiln seasoned and chemically pressure treated, complete all as specified and directed.

Second class hard wood Glazed and skeleton shutters, 30mm thick, factory made, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats, complete all as specified and directed.

Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification, complete all as specified and directed.

Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification, complete all as specified and directed.

Powder coated aluminium (thickness of powder coating shall not be less than 50 micron) window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.), complete all as specified

Powder coated aluminium (thickness of powder coating shall not be less than 50 micron) window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc., complete all as specified

Deco grill of powder coated aluminium (thickness of powder coating shall not be less than 50 micron) of 50x50mm mesh size, fitted with 'C' channel fixed with wall, complete all as specified and directed.

Powder coated aluminium (thickness of powder coating shall not be less than 50 micron) frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc., complete all as specified and directed.

Butt hinges, heavy weight, 100mm long, cold rolled mild steel, and fixed, complete all as specified and directed.

Aluminium anodised, barrel tower bolts of extruded section and fixed, 200mm long, complete all as specified and directed.

Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, 300mm long, complete all as specified and directed.

Extruded aluminium alloy handles, fabricated type, anodised of size 125mm, complete all as specified and directed.

Mild steel, 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, overall length of cover plate shall be 150mm long, including taking down old unseviceable foot operated door stopper complete all as specified and directed.

Harrison rails, anodised aluminium alloy with fixing brackets, stops, rollers etc, complete all as specified and directed.

Preparation of new surfaces of wood and wood based materials, of any description, not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed.

Sheet glass, 5.5mm thick, ordinary quality and glazing with oil putty in square not exceeding 0.5 sq. m in each pane, complete all as specified and directed.

Figured glass, 3.0mm thick, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane, complete all as specified and directed.

Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed.

Vitreous china squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe), fixed in repairs, complete all as specified and directed.

Vitreous china wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe), including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe, etc., with and including provision of seat cover black closed pattern with flat bottom with mild steel CP hinging device, fixed in repairs, complete all as specified and directed.

Vitreous china wash hand basin, flat back, size 580mm x 450mm white, excluding taps, waste pipe, chain and plug and porcelain stopper but including brackets, including cutting for and pinning in ends of brackets or erecting stand and waste coupling of PTMT, fixed in repairs, complete all as specified and directed.

Pillar taps, cast copper alloy, with capstan heads, fancy type, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed, 15mm bore, complete all as specified and directed.

PVC connections 15mm size with PTMT nuts of length 450 mm, complete all as specified and directed.

UPVC (SWR) floor trap, plain with grating including jointing with solvent cement, 75mm dia, complete all as specified and directed.

High density polyethylene pipes (HDPE), 50mm bore of pressure rating 6 kgf/cm2 fixed walls and floors, complete all as specified and directed.

PVC valveless, syphonic action type, flushing cistern, 10 litre capacity, low level, white, with inlet, ball valve, float and handle including brackets, fixed in repairs, complete all as specified and directed.

Brass chromium plated, tubular towel rail, 20mm dia, D type, 60cm long between flanges, fixed in repairs, complete all as specified and directed.

Brass chromium plated, shower rose of 125mm size, with or without swivel joint including fixing to steel pipe or union, complete all as specified and directed.

Sinks with drainage board made of stainless steel 1.00mm thick kitchen with plugs, washers and wastes; including fixing cantilever brackets and connecting union to pipe, overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm, including waste coupling, fixed in repairs, complete all as specified and directed.

Taking up or down steel tubing and connections, 15mm bore, including cleaning for refixing or removal to store, complete all as specified and directed.

Taking up or down steel tubing and connections, 20mm bore, including cleaning for refixing or removal to store, complete all as specified and directed.

Unplasticised PVC pipes, 15mm dia bore of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc., any type of pipe, complete all as specified and directed.

Unplasticised PVC pipes, 20mm dia bore of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc., any type of pipe, complete all as specified and directed.

Bib taps, cast copper alloy, fancy type, chromium plated, with long shank, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed in repairs, 15mm bore, complete all as specified and directed.

Stop valves/Angle valve, cast copper alloy, fancy type, chromium plated with long shank and cup (concealed type) screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed, 15mm bore, fixed in repairs, complete all as specified and directed.

Stop valves/Angle valve, cast copper alloy, fancy type, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed, 15mm bore, fixed in repairs, complete all as specified and directed.

Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed, 20mm bore of pipe, fixed in repairs, complete all as specified and directed.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar (1:3) for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth, complete all as specified and directed.

Taking down eaves gutters and rain water pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to store (measured overall as fixed along the centre line over fittings and accessories), complete all as specified and directed.

UPVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or floors, 110mm bore, complete all as specified and directed.

UPVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or floors, 75mm bore, complete all as specified and directed.

UPVC (SWR) branch piece with access door (single 'T') equal or unequal, 100mm bore, complete all as specified and directed.

UPVC (SWR) reducers, 110mm bore, complete all as specified and directed.

UPVC (SWR) vent cowl 75mm bore, complete all as specified and directed.

UPVC (SWR) bends any radius, 110mm bore, with access door, complete all as specified and directed.

Soap dish, chromium plated of size 150mm x 100mm, complete all as specified and directed.

Demolition of brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles, complete all as specified and directed.

Pre-cast cement concrete (1:2:4) type B1 (using 20mm graded stone aggregate) masonry with solid blocks, exceeding 10cm in width and setting in cement mortar (1:6), complete all as specified and directed.

Demolition of concrete (reinforced) in any description and in any position not otherwise specifically provided for, complete all as specified and directed.

Reinforced cement conrete (1:2:4) type B2 (Nominal Mix) (using 20mm graded stone aggregate) as in deck slabs and in shelves, complete all as specified and directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping), complete all as specified and directed.

Mild steel TMT bars 6mm to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified, complete all as specified and directed.

Brick work with fly ash bricks, straight or curved on plan to any radius, in half brick thick walls, built in CM (1:4), complete all as specified and directed.

Rendering 10 mm thick in CM (1:4) mixed with water proofing compound as per manufacurer instructions over cleaned roof surface, finished fair and even, complete all as specified and directed. Note:- Water proofing compound shall be measured and paid separately under respective item of this Schedule.

APP based polymeric membrane minimum weighing 3.5 kg / sq.m and minimum 3.0mm thick reinforced with polyester non woven fabric (weight not less than 160 gms / sqm) laid over primed surface including bituminous primer conforming to IS-3384 applied @ 0.3 litre/sq.m by forced application, complete all as specified and directed. The complete roof treatement shall be consisting of as under :- (i) Applying one coat of bituminous primer conforming to IS-3384 @ 0.3 litre / sq.m (ii) Laying of APP based membrane of specified thickness and weight. (iii) Applying one coat of bitumen of grade 85/25@ 1.2 Kg / sq.m (iv) Applying two coat of aluminium paint @ 100 ml / sq.m

Supply only integral water proofing compound

Plain cement concrete (1:3:6), type C1 (using 20mm graded stone aggregate), 50mm thick, as in plinth protection, finished fair and even without using extra cement, complete all as specified and directed.

Plain cement concrete (1:3:6), type C1 (using 20mm graded stone aggregate), 50mm thick, as in surface channels and drains, complete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred / stopped ends etc., complete all as specified and directed.

Dismantling water tanks and removing to store of capacity exc 500 litre but n exc 1000 litre, complete all as specified and directed.

Rotational moulded polyethylene water storage tanks triple layered (cylindrical vertical with closed top), 1000 litre capacity (ISI embossed), hoisted and fixed in position all as specified in SSR Part I, complete all as specified and directed.

Providing precast cement concrete (1:2:4) (using 20mm graded aggregate) as in apex stones with plain fair faces, including chamfers, eatherings, throating etc., complete all as specified and directed.

Mild steel work as in hold fasts and similar small articles conforming to Fe-290 Gde-E-165, complete all as specified and directed.

Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick (BMT- Base metal thickness) of any colour having tensile strength of 550 MPa as in roof covering / cladding to wall, fixed with self tapping screws, complete all as specified and directed.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings, complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and directed.

Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240, complete all as specified and directed.

Preparation of new or previously untreated steel and iron surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer, complete all as specified and directed.

Health faucet, chromium plated, fancy type, brass body suitable for 15mm pipe with 1.0metre length stainless steel braided rubber hose pipe and wall hook, fixed in position to wall, complete all as specified and directed.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out, complete all as specified and directed.

Sand filling 50mm thick, under floors or in foundations including watering and consolidation, complete all as specified and directed.

Machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade, with grey cement and no pigment, complete all as specified and directed

Providing precast cement concrete (1:2:4) (using 20mm graded aggregate) as in kerb stones of size 20cm x 10cm x 30cm, including necessary form work and set in cement mortar (1:4), complete all as specified and directed.

Taking down copper / aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets,bells, distribution boards and MCBs etc., and making good disturbed surfaces of walls, floors etc., complete all as specified and directed.

Point wiring complete with 1.5 sq.mm PVC insulated, single core, unsheathed multi-stranded FRLS copper conductor 1100 Volts grade, ISI marked, drawn through in and including 20mm dia rigid PVC conduit medium grade and conduit accessories, concealed in stone / brick masonry walls, roofs, floors etc, by means of saddles and clips etc, including provision of modular metal flush boxes with modular frame plate and white cover of required modules for housing switches, sockets, regulators etc., including 1.5sq.mm PVC insulated, single core, unsheathed multi-stranded FRLS copper conductor cable as earth continuity conductor and connecting to common earth dolly, complete all as specified and directed. (i) One light point controlled by one, one way modular switch, 6 Amps, Single pole, 240Volts. NOTE: (i) The quoted rate shall deemed to include the cost of metal flush boxes, modular white cover plate, provision of blank plates as per requirement etc. (ii) Quoted rate shall also deemed to include cost of making necessary chases in walls for inserting metal boxes and making good the disturbed surfaces to match with existing

All as per Sl. Item No. 105 here-in-before, but for one ceiling fan / exhaust fan point controlled by one, one way modular switch, complete all as specified and directed.

All as per Sl. Item No. 105 here-in-before, but for one bell point controlled by one, bell push, complete all as specified and directed.

All as per Sl. Item No. 105 here-in-before, but for one 3 pin, 6 Amps switch socket outlet point on independent board, complete all as specified and directed.

All as per Sl. Item No. 105 here-in-before, but for one 3 pin, 6 Amps switch socket outlet point on same board, complete all as specified and directed.

All as per Sl. Item No. 105 here-in-before, but with 2.5 sq.mm PVC insulated unsheathed multi-stranded FRLS copper conductor 1100 Volts grade, ISI marked, for 15 Amps switch socket outlet point, complete all as specified and directed.

Modular switch one way, 6 Amp, one module, (ISI marked), complete all as specified and directed.

Modular switch one way, 16 Amp, one module, (ISI marked), complete all as specified and directed.

Modular Bell push, 6 Amp, one module, (ISI marked), complete all as specified and directed.

Modular socket, 6A - 2/3 pin combined 2 module, (ISI marked), complete all as specified and directed.

Modular Socket 6A/16A - 6 pin combined 2 module, (ISI marked), complete all as specified and directed.

Bell, AC, 230 volts, single pole, music type, complete all as specified and directed.

Ceiling rose, 3 terminal / PVC / polycarbonate, isolated body, complete all as specified and directed.

High efficient surface mounted LED batten, specially designed extruded aluminium housing, high optically efficient polycorbonate diffuser, in-built electronic driver duly wired up to terminal block, IP 20, CRI>80, temperature range : 0 to 500 C, driver efficiency >85%, power factor >0.9, THD<20%, colour temperature-6500K, surge protection 2KV, 37000 burning hours, multistage isolated constant current operated driver with range 110-265V AC and safety extra low voltage safe level < 60V DC as per IEC standard, LED batten, wattage < 20W, with luminair lumen > 2000 and system efficiency > 100lm/W, complete all as specified and directed. Make:- Cat No. LUMILINEPLUSBS 20W LED865 SPCSS of Havells or techno commercially equivalent Model in BAJAJ/PHILIPS/CG/WIPRO

High efficient LED batten surface/wall mounted , specially designed extruded thermal polycarbonate housing, high optically efficient polycorbonate diffuser, in-built electronic driver duly wired up to terminal block, IP 20, CRI>80, temperature range: 0 to 500 C, driver efficiency >85%, power factor >0.95, THD<20%, colour temperature-6500K, surge protection 2.5KV, 50000 burning hours as per L70 criteria, multistage isolated constant current operated driver with range 150-270V AC and safety extra low voltage safe level < 60V DC as per IEC standard, LED batten, wattage < 20W, with luminaire lumen > 2000 and system efficiency > 100lm/W, complete all as specified and directed. Make:- Cat No. LUMILINEBS20WLED865SPCWH of Havells or techno commercially equivalent Model in BAJAJ/PHILIPS/CG/WIPRO

High efficient LED batten surface/wall mounted , specially designed extruded thermal polycarbonate housing, high optically efficient polycorbonate diffuser, in-built electronic driver duly wired up to terminal block, IP 20, CRI>80, temperature range: 0 to 500 C, driver efficiency >85%, power factor >0.95, THD<20%, colour temperature-6500K, surge protection 2.5KV, 50000 burning hours as per L70 criteria, multistage isolated constant current operated driver with range 150-270V AC and safety extra low voltage safe level < 60V DC as per IEC standard, LED batten, wattage < 10W, with luminaire lumen > 900 and system efficiency > 90lm/W, complete all as specified and directed. Make:- Cat No. LL20-111-XXX-65NE of Wipro or techno commercially equivalent Model in Havells/BAJAJ/PHILIPS/CG

High efficient LED street light with aluminium pressure Die cast housing parts for long life, pure polyester powder coated dark grey housing, high purity PMMA lenses for superior performance, toughened glass with silicon gaskets for IP65 protection, in-built electronic driver pre-wired up to terminal block, suitable for external pole dia up to 45 mm, CRI>70, temperature range- 0 to 450C, driver efficiency > 85%, power factor > 0.95, THD<10%, colour temperature- 5700K, surge protection in CM 3.5 KV, 50000 burning hours as per L70 criteria, multistage isolated constant current-constant voltage operated driver with range 150-270V AC and safety extra low voltage safe level < 60V DC as per IEC standard, LED batten, wattage < 35/36W, with luminaire lumen > 4000lm and system efficiency > 100lm/W suitable for external pole dia up to 50mm, complete all as specified and directed. MAKE:-:Cat. No. ENDURACITYLITEPLAT PLUSSL35WLED757SASYBOPC of Havells or techno commercially equivalent Model in BAJAJ/PHILIPS/CG/WIPRO

Dismantling and taking down ceiling fans, removing blades and refixing after cleaning, servicing, greasing, painting with one coat of synthetic enamel paint by sprayer with and including filling of cavities with filler and replacement of connecting cable with copper conductor flexible cable of suitable size, complete all as specified and directed.

Electronic fan regulator modular type, step type, 120W, two module, fixed as required, complete all as specified and directed.

Dismantling and taking down exhaust fans, removing blades and refixing after cleaning, servicing, greasing, painting with one coat of synthetic enamel paint by sprayer with and including filling of cavities with filler and replacement of connecting cable with copper conductor flexible cable of suitable size, complete all as specified and directed.

Sheet metal encloser for MCB DB TPN 4-way, AC 415 Volts, double door, with 200 Amps rated bus bar, including taking down old unserviceable MCB DB encloser, complete all as specified and directed.

Sheet metal encloser for MCB DB SPN 8-way, AC 240 Volts, double door, with 200 Amps rated bus bar, including taking down old unserviceable MCB DB encloser, complete all as specified and directed.

MCB FP , 32 Amps, 415 Volts, 'C' curve, 10 KA breaking capacity, complete all as specified and directed.

MCB SPN 32 Amps, 240 Volt, 50Hz, 'C' curve type, 10KA breaking capacity, complete all as specified and directed.

MCB SP 6-32Amps, 240 Volt, 50Hz, 'B' curve type, 10KA breaking capacity, complete all as specified and directed.

Sub main wiring complete with 2 runs of 6.0 sq.mm PVC insulated and unsheathed 1100V grade multistranded FRLS grade, single core copper conductor cable drawn through and including provision of concealed non-metallic rigid PVC conduit 25mm dia, medium grade and its accessories and connecting terminal ends to DB's including providing 1 run of 6.0 sq.mm PVC insulated unsheathed multistranded FRLS grade copper cable as earth continuity conductor and connecting to common earth dolly, including taking down existing unserviceable sub main wiring, complete all as specified and directed. NOTE:- (i) Two runs of 6.0 sq.mm copper conductor, one run of 6.0 sq.mm copper earth continuity conductor and one run of PVC conduit shall be measured as one unit length. (ii) Extra length of cable / wire required for connection to MCBs shall not be measured and the rate quoted per unit shall deemed to be inclusive of the same accordingly.

Sub main wiring complete with 4 runs of 6.0 sq.mm PVC insulated and unsheathed 1100V grade multistranded FRLS grade, single core copper conductor cable drawn through and including provision of concealed non-metallic rigid PVC conduit 25mm dia, medium grade and its accessories and connecting terminal ends to DB's including providing 2 runs of 6.0q.mm PVC insulated unsheathed multistranded FRLS grade copper cable as earth continuity conductor and connecting to common earth dolly, including taking down existing unserviceable sub main wiring, complete all as specified and directed. NOTE:- (i) Four runs of 6.0 sq.mm copper conductor, two runs of 6.0 sq.mm copper earth continuity conductor and one run of PVC conduit shall be measured as one unit length. (ii) Extra length of cable / wire required for connection to MCBs shall not be measured and the rate quoted per unit shall deemed to be inclusive of the same accordingly.

Heavy duty exhaust fan 450mm sweep 1400RPM, and blades with louvers and shutters without regulator suitable for 230V single phase AC supply with all fixing arrangments to fix on wall, including making holes on brick / stone walls and making good disturbed surfaces to match with the existing, including provision of 3-way PVC connector, copper bunched flexible three core 1.5sq.mm PVC insulated cable from connection point to fan, writing MES number on exhaust fan motor, complete all as specified and directed

Earthing complete with GI earth plate electrode 600mm x 600mm x 6.0mm thick buried directly in ground vertically to a depth of not less than 2.25m deep below ground level with the top edge of earth plate at a depth of not less than 1.5m below ground level connected to GI earth strip of 25x 4mm by means of bolts, nuts, washers etc., GI earth strip shall be protected by 40mm dia GI pipe 'light grade', watering pipe 20mm dia GI pipe 'medium grade', GI wire meshed funnel, alternate layer of charcoal and salt on all side to earth plate upto a thickness of 150mm, filling of black cotton soil in earth pit upto GL, and connected to earth plate including necessary excavation & earthwork, PCC (1:3:6) type C1 earth chamber with 40mm x 40mm x 6mm MS angle iron frame, 40mm thick RCC cover (1:2:4) type B1 mix with 8mm dia nominal reinforcement @ 75mm c/c both ways etc., with plastering 15mm thick in CM (1:6) internally and upto 150mm below GL externally, PGI funnel with wire mesh, complete all as shown in electrical plate No.3 connected to earthing test point, including testing on completion, complete all as speciified and as directed. NOTE:- (a) Rate quoted shall deemed to include cost of excavation in any type of strata, RFR and removal upto 50metre.

ZOOM ENTERPRISES

Sreema Enterprises

WELTRONENGINEERINGSERVICES

THOMSONS CONSTRUCTIONS

KENZ CONSTRUCTIONS