E-Tender for Repair and renovation of Laboratory at Tapi Division, CWC, Surat

Amount

Repair and renovation of Laboratory at 2nd floor under Tapi Division, CWC, Surat

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :Of area 3 sq. metres and below

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead - For thickness of tiles 10 mm to 25 mm

Dismantling stone slab roofing over wooden karries or R.C.C. battens (dismantling karries and battens to be paid for separately), including stacking of serviceable material and disposal of unserviceable material within 50 metres lead.

Dismantling wooden boardings in lining of walls and partitions, excluding supporting members but including stacking within 50 metres lead :Thickness above 10 mm up to 25 mm

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.

15 mm cement plaster on the rough side of single or half brick wall of mix 1:4 (1 cement: 4 fine sand)- two sides

Distempering with dry distemper of approved brand and manufacture (two or more coats) of required shade on new work, over and including water thinnable priming coat to give an even shade.

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade :Two or more coats on new work

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete.

Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complete, including painting of fittings and brackets, cutting and making good the wall wherever required :Size 600x450x200 mm

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. :15 mm nominal bore

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Providing and fixing 25 mm thick shutters for cup board etc.Ist class teak wood including nickel plated bright finished M.S. piano hinges with necessary screws

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. 32 mm dia nominal bore

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make confirming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i,e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately):(a) For fixed portion -Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make confirming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i,e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately)(b) For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) - Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 5 mm thickness (weight notless than 12.50 kg/ sqm)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS:12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer-in-charge Pre-laminated particle board with decorative lamination on both sides( Total 12mm thick pre laminated particle board work)

Providing and fixing aluminium tubular handle bar 32 mm outer dia,3.0 mm thick & 2100 mm long with SS screws etc. complete as per direction of Engineer-in-charge Polyester powder coated minimum thickness 50 micron aluminium tubular handle bar

Providing & fixing of Dash fastener/chemical fastener @ 0.40m-0.45m spacing

Providing and fixing Brass 100mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc.complete.

Providing & fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS: 1868) transperant or dyed to required colour or shade, with necessary screws etc complete: 250x10mm

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.Twin rubber stopper.

Providing & fixing Hydraulic door closer tubular type Aluminium section body

Supply, installation, testing & commissioning of the following electrical Item of ISI mark as per approved quality:- Air conditioner (Split type) – 2 Ton Specification:- Type of Air Conditioner-High wall Split AC (Hot and Cold) Air Conditioning Technology- Hot and Cold Compressor (Speed Type)- Variable speed compressor which adjusts power depending on heat load. Heating Mechanism-Heat Pump Minimum Set Temperature- 16 degree Celsius Maximum Set Temperature- 30 degree Celsius Nominal Cooling Capacity (kcal/hr)-6000 for 2.0 TR Nominal Heating Capacity-90 to 100% of Cooling Capacity Coil Material (Evaporator)-Copper Coil Material (Condenser)-Copper Fin Material (Evaporator)-Aluminium Fin Material (Condenser)-Aluminium Eco-friendly refrigerant-Yes BEE Star Rating-3 to 5 Minimum length of copper pipe and suitable connecting electrical cable for installation and commissioning - inclusive in the scope of supply 3 meter Warranty on machine-1 to 2 year Warranty on Compressor-2 to 5 year Installation and Commissioning-With Installation and Commissioning

Supply, installation, testing & commissioning of the following electrical work of ISI mark as per approved quality:- i. Tub light- 20no., Special Feature- Energy Efficient, Light Type- LED, Indoor/Outdoor Usage- Outdoor, Indoor, Wattage-18 Watts, Light Colour- White ii. Ceiling fan-5no. TECHNICAL SPECIFICATIONS: Sweep 1200 mm, Power consumption 74 W, Speed 380 RPM, Air delivery 230 CMM. QUALITY COMPONENTS: 100% copper motor, double ball bearings, dynamically balanced blades and anti-rust aluminium body. Warranty-1year. iii. Wall fan- 10no. Elegantly designed fan base, 120 ribs guard. Oscillation degree: 60˚,Pull cord control for speed and oscillation on-off, Remote control option – No, Aerodynamically, designed and balanced blades, Speed: 1350 RPM. Rated voltage 230 V, Air Delivery: 72 CMM Blade: Aerodynamically designed & balanced blades; TOP: Thermal overload protector (TOP) helps in protecting the motor in case of any high voltage fluctuation; Guard: 120 Spokes; Motor speeds (No.): 3 ; Noise level: 63.2 dB ; Power consumption: 50 W, Rated voltage: 230 V, Rated frequency: 50 Hz ; Items Included: Motor ,mounting accessories kit, blade, guard set, guard ring, guarantee card, Warranty: 1 year on product iv. MCB 15/16 A-10no. Material: PVC Plastic, Color: White, Item Dimension: 445mm x 408mm x 240mm, Package, 15/16 A MCB SP B Curve v. Switch board- 20 nos- 2 no. sockets ISI mark and 2no. switches ISI mark in each board , Voltage-220 Volts, current- 5 Amp (AC) with suitable wiring as per requirement vi. Switch board- 10 nos- 1 no. sockets ISI mark and 1no. switches ISI mark in each board , Voltage-220 Volts, currect-15/16 Amp (AC) with suitable wiring as per requirement vii. Wiring for Switch points/ MCB point /light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with piano type switch, phenolic laminated sheet, suitable size M.S. box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required. Total number of domestic points-35 viii. Wiring for Switch points/ MCB point /light point/ fan point/ exhaust fan point/ call bell point with 2.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with piano type switch, phenolic laminated sheet, suitable size M.S. box and earthing the point with 2.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required. Total number of power points-10

VNS ENTERPRISE

ORIENTAL INTEGRATED FACILITY MANAGEMENT PVT. LTD.