CONSTRUCTION OF FIRE STATION & STAFF QUARTERS AT RAMOL-HATHIJAN (TP NO 76, FP NO 115-1) IN RAMOL WARD, EAST ZONE, UNDER BUILDING PROJECT DEPARTMENT, AMC

I/We am/are willing to carry out work at __________% above / below (should be written in figures and words) the estimated cost

mentioned above. The amount of my/our tender works out as under

Estimated cost put to tender : Rs. 41,01,86,912.24 Estimated cost put to tender : Rs.

Add_____% Above : Rs ___________ Deduct_____% Below : Rs ___________

Total : Rs___________ Total : Rs___________

Note-1 The contractor should get the sample of material in respect of quality and source of supply or manufacturer approved by

Consultant / AMC in all cases. All such approved samples should be kept at site in the custody of EIC-CMC/PMC/AMC. The tests

for the make in external laboratory in presence of CMC/PMC/AMC to be carried out by Contractor at his own cost as per relevant

latest codes. Reinforcement steel & cement original purchase bills shall be produced to CMC/PMC/AMC as and when asked for.

Note-2 Rate includes for any height, any level, any lead & lift and as per directed by EIC.

Note-3 For Fire Fighting System Autoglow Mandatory Signages and NOC Process and charges of NOC are included.

Signature of Contractor Additional City Engineer

Seal Building Project

Date Ahmedabad Municipal Corporation

AHMEDABAD MUNICIPAL CORPORATION

Construction of Fire Station and Staff Quarters at T.P 76 F.P. 115-1 in Ramol Ward, East Zone, Ahmedabad city under

Building Project Department.

SUBESTIMATE - 01 : STRUCTURAL WORK

S. NO. ITEM DESCRIPTION AMOUNT

1 STRUCTURAL WORK

AHMEDABAD MUNICIPAL CORPORATION

Construction of Fire Station and Staff Quarters at T.P 76 F.P. 115-1 in Ramol Ward, East Zone, Ahmedabad city under Building Project Department.

BOQ FOR SUBESTIMATE - 01 : STRUCTURAL WORK

Item no. Item Description Unit Rate Total Qty. Amount

Excavation for foundation up to 1.5 m DEPTH including sorting out and stacking of useful material sand disposing off

the excavated stuff upto 50 Meter lead.(A) Loose or soft soil

Excavation for foundation up to 1.5 m TO 3.0M DEPTH including sorting out and stacking of useful material sand

disposing off the excavated stuff upto 50 Meter lead.(A) Loose or soft soil

Excavation for foundation up to 3.0M TO 5.0M DEPTH including sorting out and stacking of useful material sand

disposing off the excavated stuff upto 50 Meter lead.(A) Loose or soft soil

Filling available excavated earth (excluding rock) in trenches. plinth, sides of foundations etc. in layers not exceeding

20cm. In depth consolidating each disposited layer by ramming and watering.

Providing and laying cement concrete 1:2:4 (1-Cement:2-Coarse sand:4-graded stone aggregates 20mm nominal

size) and curing complete excluding cost of formwork in (A) Foundation and Plinth

Providing and laying in position Ready Mixed M- 250 grade concrete for reinforced cement conctere work , using

cement content as per approved Design Mix manufactured in fully automatic batching plant and transported to site of

work in transit mixer for a lead up to 10 kms having continuous agitated mixer, manufactured as per mix design of

specified grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer to site of laying,

6 excluding the cost of centering shuttering finishing and reinforcement including cost of admixtures in recommended CUM 4,853.56 681.63

proportions as per IS: 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength

and durability as per direction of the Engineer - in - charge. Without Fly Ash (Min cement level as per latest IS

shall be maintained) (Cement level 450 kg ) (GRADE SLAB)

Providing and laying in position Ready Mixed M-300 grade concrete for reinforced cement conctere work , using

cement content as per approved Design Mix manufactured in fully automatic batching plant and transported to site of

work in transit mixer for a lead up to 10 kms having continuous agitated mixer, manufactured as per mix design of

specified grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer to site of laying,

7 excluding the cost of centering shuttering finishing and reinforcement including cost of admixtures in recommended CUM 5,043.66 1,457.46

proportions as per IS: 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength

and durability as per direction of the Engineer - in - charge. Without Fly Ash (Min cement level as per latest IS

shall be maintained) (Cement level 475 kg ) (Foundation)

Bored cast-in-situ M30 grade R.C.C. pile excluding reinforcement complete as per drawing and technical

specifications and removal of excavated earth with all lifts and lead upto 1000 m. (Pile diameter- 300 mm)

Providing and laying in position Ready Mixed M-300 grade concrete for reinforced cement conctere work , using

cement content as per approved Design Mix manufactured in fully automatic batching plant and transported to site of

work in transit mixer for a lead up to 10 kms having continuous agitated mixer, manufactured as per mix design of

specified grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer to site of laying,

9 excluding the cost of centering shuttering finishing and reinforcement including cost of admixtures in recommended CUM 5,245.98 1,802.32

proportions as per IS: 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength

and durability as per direction of the Engineer - in - charge. Without Fly Ash (Min cement level as per latest IS

shall be maintained) (Cement level 475 kg ) (RCC BEAM) for all floor

Item no. Item Description Unit Rate Total Qty. Amount

Providing and laying in position Ready Mixed M-450 grade concrete for reinforced cement conctere work , using

cement content as per approved Design Mix manufactured in fully automatic batching plant and transported to site of

work in transit mixer for a lead up to 10 kms having continuous agitated mixer, manufactured as per mix design of

specified grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer to site of laying,

10 excluding the cost of centering shuttering finishing and reinforcement including cost of admixtures in recommended CUM 5,450.46 344.90

proportions as per IS: 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength

and durability as per direction of the Engineer - in - charge. Without Fly Ash (Min cement level as per latest IS

shall be maintained) (Cement level 550 kg ) (RCC COLUMN) for all floor

Providing and laying in position Ready Mixed M-400 grade concrete for reinforced cement conctere work , using

cement content as per approved Design Mix manufactured in fully automatic batching plant and transported to site of

work in transit mixer for a lead up to 10 kms having continuous agitated mixer, manufactured as per mix design of

specified grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer to site of laying,

11 excluding the cost of centering shuttering finishing and reinforcement including cost of admixtures in recommended CUM 5,395.77 234.55

proportions as per IS: 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength

and durability as per direction of the Engineer - in - charge. Without Fly Ash (Min cement level as per latest IS

shall be maintained) (Cement level 525 kg ) (RCC COLUMN) for all floor

Providing and laying in position Ready Mixed M-350 grade concrete for reinforced cement conctere work , using

cement content as per approved Design Mix manufactured in fully automatic batching plant and transported to site of

work in transit mixer for a lead up to 10 kms having continuous agitated mixer, manufactured as per mix design of

specified grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer to site of laying,

12 excluding the cost of centering shuttering finishing and reinforcement including cost of admixtures in recommended CUM 5,343.26 411.82

proportions as per IS: 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength

and durability as per direction of the Engineer - in - charge. Without Fly Ash (Min cement level as per latest IS

shall be maintained) (Cement level 500 kg ) (RCC COLUMN)

Providing and laying in position Ready Mixed M-300 grade concrete for reinforced cement conctere work , using

cement content as per approved Design Mix manufactured in fully automatic batching plant and transported to site of

work in transit mixer for a lead up to 10 kms having continuous agitated mixer, manufactured as per mix design of

specified grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer to site of laying,

13 excluding the cost of centering shuttering finishing and reinforcement including cost of admixtures in recommended CUM 5,245.98 21.84

proportions as per IS: 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength

and durability as per direction of the Engineer - in - charge. Without Fly Ash (Min cement level as per latest IS

shall be maintained) (Cement level 475 kg ) (RCC COLUMN)

Providing and laying in position Ready Mixed M-300 grade concrete for reinforced cement conctere work , using

cement content as per approved Design Mix manufactured in fully automatic batching plant and transported to site of

work in transit mixer for a lead up to 10 kms having continuous agitated mixer, manufactured as per mix design of

specified grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer to site of laying,

14 excluding the cost of centering shuttering finishing and reinforcement including cost of admixtures in recommended CUM 5,245.98 787.22

proportions as per IS: 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength

and durability as per direction of the Engineer - in - charge. Without Fly Ash (Min cement level as per latest IS

shall be maintained) (Cement level 475 kg ) (RCC WALL) for all floor

Item no. Item Description Unit Rate Total Qty. Amount

Providing and laying in position Ready Mixed M-300 grade concrete for reinforced cement conctere work , using

cement content as per approved Design Mix manufactured in fully automatic batching plant and transported to site of

work in transit mixer for a lead up to 10 kms having continuous agitated mixer, manufactured as per mix design of

specified grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer to site of laying,

15 excluding the cost of centering shuttering finishing and reinforcement including cost of admixtures in recommended CUM 5,245.98 2,387.57

proportions as per IS: 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength

and durability as per direction of the Engineer - in - charge. Without Fly Ash (Min cement level as per latest IS

shall be maintained) (Cement level 475 kg ) (RCC SLAB) for all floor

Providing and laying cushioning layer on R.C.C. Slab consisting of 75mm thick lime, concrete using brick aggregate

of 20mm nominal size mortar compresing of 1-Lime : 2- fine sand

Providing and laying in position Ready Mixed M-300 grade concrete for reinforced cement conctere work , using

cement content as per approved Design Mix manufactured in fully automatic batching plant and transported to site of

work in transit mixer for a lead up to 10 kms having continuous agitated mixer, manufactured as per mix design of

specified grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer to site of laying,

17 excluding the cost of centering shuttering finishing and reinforcement including cost of admixtures in recommended CUM 5,245.98 148.80

proportions as per IS: 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength

and durability as per direction of the Engineer - in - charge. Without Fly Ash (Min cement level as per latest IS

shall be maintained) (Cement level 500 kg ) (STAIRCASE)

Providing and laying design mix cement concrete of M‑30 grade for RCC road, using cement content as per

approved mix design, coarse sand and graded stone aggregate of 40 mm nominal size, batching and mixing at site /

RMC plant, laying, spreading and compacting mechanically using needle vibrators and surface vibrators, followed by

vacuum dewatering process with floor hardener, finishing by floating and brooming with wire brush, levelling to

18 required slope/camber and textured finish, including providing steel formwork with sturdy MS channel sections, CUM 6,207.00 286.29

curing, forming contraction, expansion, construction and longitudinal joints by groove cutting machine, and providing

and filling joints with approved joint filler and sealants, complete all as per IRC specifications and directions of

Engineer‑in‑Charge.

Providing, laying, spreading and compacting graded stone aggregate (size range 53 mm to 0.075 mm ) to wet mix

macadam (WMM) specification including premixing the material with water at OMC in for all leads & lifts, laying in

19 uniform layers with mechanical paver finisher in sub- base / base course on well prepared surface and compacting CUM 1,056.45 143.15

with vibratory roller of 8 to 10 tonne capacity to achievethe desired density, complete as per specifications and

directions of Engineer-in-Charge.

Construction of granular sub-base by providing close graded material conforming to specifications, mixing in a

mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in

20 uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory roller to CUM 953.49 214.72

achieve the desired density, complete as per specifications and directions of Engineer-in-Charge

With material conforming to Grade-I (size range 75mm to 0.075 mm) having CBR Value -

Providing and laying TMT Bar FE-500D reinforcement for R.C.C. work and straightening, cutting, bending, binding &

21 placing in position completed upto all floor all level as per I.S. Standard. complete. As per drawings and design kg 79.51 10,90,942.52

supplied by architect and instruction given by authority and E.I.C.

Providing formwork of ordinary timber planking so as to give a rough finish including centering shuttering strutting and

propping etc. Height of propping and centering below supporting floor to ceiling not exceeding 4 M. and removal of

22 the same for in situ reinforced concrete and plain concrete work in. (A) Foundations Footings Bases of Columns SQM 171.68 942.68

etc. and Mass concrete.

Item no. Item Description Unit Rate Total Qty. Amount

Providing formwork of ordinary timber planking so as to give a rough finish including centering shuttering strutting and

propping etc. height of propping and centering below supporting floor to ceiling not exceeding 4 M. and removal of

23 the same for in situ reinforced concrete and plain concrete work in. (G) Columns PillarsPosts and struts. (1) SQM 297.68 9,712.27

Square Rectangular Polygonal in plan.

Extra for Providing formwork with sheathing steel sheets so as to give a fair finish in (G) Columns, Pillars, Posts

and struts. (1) Square, Rectangular or polygonal in plan.

Extra for additional height of propping and centering where the height of propping and centering exceeds 4 .O M

25 between supporting floor to ceiling including temporary brick or stone pillars for supporting as required. (ii) Height SQM 682.01 71.21

more than 5.0M.and upto 6.0 M.

Extra for Providing formwork with sheathing steel sheets so as to give a fair finish in (G) Columns, Pillars, Posts

and struts. (1) Square, Rectangular or polygonal in plan.

Providing formwork of ordinary timber planking so as to give a rough finish including centering shuttering strutting and

propping etc. height of propping and centering below supporting floor to ceiling not exceeding 4 M. and removal of

27 the same for in situ reinforced concrete and plain concrete work in. (C) Vertical surface such as walls (any SQM 229.95 6,433.77

thickness) partitions and the like including attached buttresses & string course & the like.

Extra for Providing formwork with sheathing steel sheets so as to give a fair finish in (C) Vertical surface such as

walls (any thickness) partitions and the like including attached buttresses & string course & the like.

Extra for additional height of propping and centering where the height of propping and centering exceeds 4 .O M

29 between supporting floor to ceiling including temporary brick or stone pillars for supporting as required. (ii)Height SQM 386.48 - -

more than 5.0 M.and upto 6.0 M.

Extra for Providing formwork with sheathing steel sheets so as to give a fair finish in (C) Vertical surface such as

walls (any thickness) partitions and the like including attached buttresses & string course & the like.

Providing formwork of ordinary timber planking so as to give a rough finish including centering shuttering strutting and

propping etc. Height of propping and centering below supporting floor to ceiling not exceeding 4 M. and removal of

31 the same for in situ reinforced concrete and plain concrete work in. (B) Flat surfaces such as soffits of supspened SQM 252.00 12,626.81

floors slabs Landings and the like. (1) Floors etc. upto 200 mm in thickness.

Extra for Providing formwork with sheathing steel sheets so as to give a fair finish in (B)Flat surfaces such as

soffits of slabs Landings and the like. (1) Floors etc. upto 200mm in thickness.

Providing formwork of ordinary timber planking so as to give a rough finish including centering shuttering strutting and

propping etc. height of propping and centering below supporting floor to ceiling not exceeding 4 M. and removal of

33 the same for in situ reinforced concrete and plain concrete work in. (H) (1) Sides and soffits of Beams Beam SQM 192.15 22,868.27

Haunchings cantilevers Girders Bressumers and Lintels not exceeding 1 M. in Depth.

Extra for Providing formwork with sheathing steel sheets so as to give a fair finish in (H)(1) Sides and soffits of

Beams, Beam Haunchingscantilevers Girders, Bressumers and Lintels not exceeding 1 M. in Depth.

Providing formwork of ordinary timber planking so as to give a rough finish including centering shuttering strutting and

propping etc. Height of propping and centering below supporting floor to ceiling not exceeding 4 M. and removal of

35 the same for in situ reinforced concrete and plain concrete work in. M) Staircase with slopingor SQM 242.55 787.45

stepped soffits including risers and stringers excluding landing.

Extra for Providing formwork with sheathing steel sheets so as to give a fair finish in (M)Staircase with sloping or

stepped soffits including sisers and stringers excluding landing.

Item no. Item Description Unit Rate Total Qty. Amount

Providing and fixing HILTI rebar (10mm diameter).The work shall be carried out by the technical workmens/agency

37 approved by the manufacturer and under technical supervision including all materials,tool tackles, labour No. 465.00 30.00

etc.complete as per drawings and instruction given by authority and E.I.C.

Providing and fixing HILTI rebar (12mm diameter).The work shall be carried out by the technical workmens/agency

38 approved by the manufacturer and under technical supervision including all materials,tool tackles, labour No. 608.00 30.00

etc.complete as per drawings and instruction given by authority and E.I.C.

Providing and fixing HILTI rebar (16mm diameter). The work shall be carried out by the technical workmens/agency

39 approved by the manufacturer and under technical supervision including all materials,tool tackles, labour No. 1,202.00 30.00

etc.complete as per drawings and instruction given by authority and E.I.C.

Providing and fixing HILTI rebar (20mm diameter). The work shall be carried out by the technical workmens/agency

40 approved by the manufacturer and under technical supervision including all materials,tool tackles, labour No. 2,063.00 30.00

etc.complete as per drawings and instruction given by authority and E.I.C.

Providing and fixing HILTI Anchor (10mm diameter). The work shall be carried out by the technical

41 workmens/agency approved by the manufacturer and under technical supervision including all materials,tool tackles, No. 846.00 30.00

labour etc.complete as per drawings and instruction given by authority and E.I.C.

Providing and fixing HILTI Anchor (12mm diameter). The work shall be carried out by the technical

42 workmens/agency approved by the manufacturer and under technical supervision including all materials,tool tackles, No. 1,245.00 30.00

labour etc.complete as per drawings and instruction given by authority and E.I.C.

Providing and fixing HILTI Anchor (16mm diameter). The work shall be carried out by the technical

43 workmens/agency approved by the manufacturer and under technical supervision including all materials,tool tackles, No. 2,295.00 30.00

labour etc.complete as per drawings and instruction given by authority and E.I.C.

Providing and fixing HILTI Anchor (20mm diameter). The work shall be carried out by the technical

44 workmens/agency approved by the manufacturer and under technical supervision including all materials,tool tackles, No. 4,451.00 30.00

labour etc.complete as per drawings and instruction given by authority and E.I.C.

Providing and fixing UPVC/PVC sleeves of required diameter (compressive strength ≥ 6 kg/cm²) up to 0.5 m long,

cast in RCC slabs, beams, walls, etc., for services and utilities, complete. 1)50mm dia.

Providing and fixing UPVC/PVC sleeves of required diameter (compressive strength ≥ 6 kg/cm²) up to 0.5 m long,

cast in RCC slabs, beams, walls, etc., for services and utilities, complete. 1)75mm dia.

Providing and fixing UPVC/PVC sleeves of required diameter (compressive strength ≥ 6 kg/cm²) up to 0.5 m long,

cast in RCC slabs, beams, walls, etc., for services and utilities, complete. 1)110mm dia.

Providing and fixing in position high-grade PVC water stopper of size 250 mm wide × 10 mm thick at construction /

48 expansion joints in underground water tanks, STP structures and similar water-retaining structures, complete as per Rmt 311.00 1,513.00

drawings and directions of Engineer-in-Charge

AHMEDABAD MUNICIPAL CORPORATION

Construction of Fire Station and Staff Quarters at T.P 76 F.P. 115-1 in Ramol Ward, East Zone, Ahmedabad city under

Building Project Department.

SUBESTIMATE - 02 : CIVIL WORK

S. NO. ITEM DESCRIPTION AMOUNT

B MASONARY WORK

C PLASTER & CLADDING WORK

D FLOORING & PAVING WORK

E PAINTING AND POINTING

F CEILING & PARTITION WORK

G WATER PROOFING WORK

H DOOR AND WINDOW WORK

J MISCELLENEOUS

K FURNITURE WORK

AHMEDABAD MUNICIPAL CORPORATION

Construction of Fire Station and Staff Quarters at T.P 76 F.P. 115-1 in Ramol Ward, East Zone, Ahmedabad city under Building Project Department.

BOQ FOR SUBESTIMATE - 02 : CIVIL WORK

Item no. Item Description Unit Rate Total Qty. Amount

Earthwork for embankment including breaking clods, dressing with all lead and lift and including watering rolling

1 and consolidation of subgrade in layers at O.M.C. to required dry density including filling the depression which CUM 151.00 500.00

occur during the process using power roller 8T to 10T. From Borrow area as per lead available.

Filling in foundation and plinth with murrum or selected soil in layers of 20cm. thickness including watering,

ramming and consolidating etc. complete.

Conveyance charge of earth, lime, murrum, building rubbish, manure, garbage, sludge, excavated rock, fly ash,

aggregates of any kind executed outside the road site. Rate also includes spreading & levelling etc complete.

Internal conveyance above 50 mt done within the work site is not payable. (R&B 2023-24 Statement No.5

(3.2.1.A.2. Earth) Page no.5

3 Lead From 5 Km to 10 Km. CUM 417.67 7,365.00

4 Lead From 10 Km to 15 Km. CUM 425.87 7,365.00

5 Lead From 15 Km to 25 Km. CUM 433.32 7,365.00

TOTAL OF EARTH WORK

B MASONARY WORK

Brick work using common burnt clay building bricks having crushing strength not less than 35 kg./Sq.Cm. in

foundation and plinth in Cement Mortar 1:5. (1- Cement : 5 -fine sand)(B) Conventional

Extra for brick work in superstructure above plinth level upto floor two level (B) Conventional

Basement Cu.m 4,283.91 40.00

Ground Floor Cu.m 4,283.91 355.00

1st Floor Cu.m 4,283.91 285.00

Extra for brick work in superstructure above floor two level Item No. 1(6.12) (B) Conventional

2nd Floor Cu.m 4,324.00 415.00

3rd Floor Cu.m 4,364.09 289.00

4th Floor Cu.m 4,404.18 175.00

5th Floor Cu.m 4,444.27 178.00

6th Floor Cu.m 4,484.36 175.00

7th Floor Cu.m 4,524.45 175.00

8th Floor Cu.m 4,564.54 178.00

9th Floor Cu.m 4,604.63 175.00

10th Floor Cu.m 4,644.72 175.00

Terrace / Mumty Cu.m 4,684.81 134.00

(i) Half brick masonry in common brunt clay building bricks having crushing strength not less than 35 Kg/Sq.Cm.

in Cement mortar 1:4 (1-Cement : 4 -coarse sand ) in foundation and plinth (B) Conventional : Extra for brick work

9 in superstructure above floor two level Item No. 5 (B) Coventional

Ground Floor SQM 646.70 59.00

1st Floor SQM 646.70 480.00

Item no. Item Description Unit Rate Total Qty. Amount

Extra for brick work in superstructure above floor

two level Item No. 5 (B) Coventional

2nd Floor SQM 652.64 1,041.00

3rd Floor SQM 692.73 493.00

4th Floor SQM 732.82 448.00

5th Floor SQM 772.91 448.00

6th Floor SQM 813.00 448.00

7th Floor SQM 853.09 448.00

8th Floor SQM 893.18 448.00

9th Floor SQM 933.27 448.00

10th Floor SQM 973.36 448.00

Terrace / Mumty SQM

Providing and filling sunken portion with light weight AAC block bats of size 40–60 mm, including placing, packing

and filling voids with cement sand mortar 1:5 (1 cement : 5 coarse sand) admixed with integral waterproofing

11 compound conforming to IS 2645, properly compacted and levelled, and finishing with 25 mm thick cement sand cum 6,407.00 117.00

mortar screed 1:4 laid to required levels and slopes, smooth and ready to receive floor finish, complete as

TOTAL OF MASONARY WORK

C PLASTER & CLADDING WORK

Providing 10mm thick cement plaster in single coat on brick/concrete walls for interior plastering upto floor two

level and finished even and smooth in (i)Cement mortar 1:3 (1-cement:3-sand)

Basement SQM 127.58 1,714.00

Ground Floor SQM 127.58 2,430.00

1st Floor SQM 127.58 2,824.00

Extra over items for interior plastering above floor two level for every

additional storey height. (1) Single coat plaster

2nd Floor SQM 150.74 3,450.00

3rd Floor SQM 173.90 1,928.00

4th Floor SQM 197.06 1,928.00

5th Floor SQM 220.22 1,928.00

6th Floor SQM 243.38 1,928.00

7th Floor SQM 266.54 1,928.00

8th Floor SQM 289.70 1,928.00

9th Floor SQM 312.86 1,928.00

10th Floor SQM 336.02 1,928.00

Terrace / Mumty SQM

20mm thick sand faced cement plaster on walls upto height 10 metres above ground level consisting of 12mm

14 thick backing coat of C.M. 1:3 (1-cement : 3-sand) and 8mm thick finishing coat of C.M. 1:1 (1-cement : 1-sand)

Ground Floor SQM 297.68 3,332.00

1st Floor SQM 297.68 2,236.00

2nd Floor SQM 297.68 3,233.00

Item no. Item Description Unit Rate Total Qty. Amount

Extra over items for interior plastering above floor two level for every additional storey height.(2) Two coat plaster

3rd Floor SQM 324.14 2,263.00

4th Floor SQM 350.60 1,836.00

5th Floor SQM 377.06 1,859.00

6th Floor SQM 403.52 1,836.00

7th Floor SQM 429.98 1,836.00

8th Floor SQM 456.44 1,859.00

9th Floor SQM 482.90 1,836.00

10th Floor SQM 509.36 1,836.00

Terrace / Mumty SQM 535.82 1,135.00

Providing 15mm thick cement plaster in single coat on Rough (Similar)side of single or half brick walls for interior

16 plastering upto floor two level and finished even and smooth in (ii) Cement mortar 1:4 (1-cement :4-sand)

Basement SQM 155.61 14.00

Ground Floor SQM 155.61 226.00

1st Floor SQM 155.61 301.00

Extra over for interior plastering above floor two level for every

additional storey height. (1) Single coat plaster

2nd Floor SQM 178.77 571.00

3rd Floor SQM 201.93 195.00

4th Floor SQM 225.09 195.00

5th Floor SQM 248.25 195.00

6th Floor SQM 271.41 195.00

7th Floor SQM 294.57 195.00

8th Floor SQM 317.73 195.00

9th Floor SQM 340.89 195.00

10th Floor SQM 364.05 195.00

Extra over items for plastering on ceilings and sofits of stairs upto floor two level instead of plastering on walls.

18 Extra over for finishing with a floating coat of neat cement slurry

Basement SQM 227.91 2,043.00

Ground Floor SQM 227.91 1,226.00

1st Floor SQM 227.91 1,104.00

Extra over for plastering on ceiling and soffits of stairs above floor two level for every additional storey height.

19 Extra over for finishing with a floating coat of neat cement slurry

2nd Floor SQM 296.75 888.00

3rd Floor SQM 365.59 765.00

4th Floor SQM 434.43 690.00

5th Floor SQM 503.27 690.00

6th Floor SQM 572.11 690.00

7th Floor SQM 640.95 690.00

Item no. Item Description Unit Rate Total Qty. Amount

8th Floor SQM 709.79 690.00

9th Floor SQM 778.63 690.00

10th Floor SQM 847.47 690.00

Terrace / Mumty SQM 916.31 108.00

Providing 15mm thick cement plaster in single coat on Rough (Similar)side of single or half brick walls for interior

20 plastering upto floor two level and finished even and smooth in (ii) Cement mortar 1:4 (1-cement :4-sand). Extra

over items for finishing with a floating coat of neat cement slurry.

Basement SQM 203.34 119.00

Ground Floor SQM 203.34 474.00

1st Floor SQM 203.34 474.00

Extra over for interior plastering above floor two level for every additional storey height.(2) Two coat plaster. Extra

21 over items for finishing with a floating coat of neat cement slurry.

2nd Floor SQM 277.53 601.00

3rd Floor SQM 351.72 403.00

4th Floor SQM 425.91 403.00

5th Floor SQM 500.10 403.00

6th Floor SQM 574.29 403.00

7th Floor SQM 648.48 403.00

8th Floor SQM 722.67 403.00

9th Floor SQM 796.86 403.00

10th Floor SQM 871.05 403.00

Terrace / Mumty SQM 945.24 119.00

WET CLADDING POLISHED GRANITE : Providing and fixing machine cut, composite patterned wall wet

cladding out of 18-20mm thick mirror polish granite machine cut, machine polished to walls and columns. Stone

fixed with required stainless steel pins / dowels / cramps including drilling holes, making notches etc. for

22 securedly fixing with pins / cramps to wall. Stone fixed in position with approved readymix ploymer based SQM 4,546.00 332.00

adhesive in line and level and in pattern as shown in the drawing. Joints cleaned, grouted with approved ready

made ploymer modified grout or cured and cleaned, further to include required double legged independent

scaffolding etc. complete to the satisfaction of the EIC.

Washed stone grit plaster on exterior walls height upto 10 metre above ground level, in two layers, under layer

mm cement plaster 1:4 (1 cement : 4 coarse sand ), furrowing the under layer with scratching tool, applying

cement slurry on the under layer @ 2 Kg of cement per square metre, top layer 15 mm cement plaster 1:1/ 2:2 (1

23 cement: 1/2 coarse sand : 2 stone chipping 10 mm nominal size), in panels with groove all around as per SQM 647.00 321.00

approved pattern, including scrubbing and washing the top layer with brushes and water to expose the stone

chippings ,complete as per specification and direction of Engineer-in-charge (payment for providing grooves shall

be made separately).

TOTAL OF PLASTER & CLADDING WORK

Item no. Item Description Unit Rate Total Qty. Amount

D FLOORING & PAVING WORK

Granite Flooring - Leather Finish : Providing and laying lether finish Granite stone flooring in required design

and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings

with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement: 4 coarse sand) laid

24 and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade SQM 1,921.00 1,417.00

including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.

lether finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent

Granite Skirting / Riser / vertical - Leather finish : Providing and laying Granite stone slab 25mm thick in risers

of steps,skirting Dedo and pillars laid on 10mm thick cement mortar 1:3 (1-Cement : 3 coarse sand) and jointed

25 with gray cement slury mixed with pigment to match the shade of slab including rubbing and polishing etc. SQM 2,323.00 30.00

Granite Flooring - Polished : Providing and laying Polished Granite stone flooring in required design and

patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with

18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement: 4 coarse sand) laid and

26 jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade SQM 2,250.00 576.00

including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.

Polished granite stone slab of colour black, cherry/ruby red or equivalent.

Polishe Kota Stone Flooring : Providing and laying polished Kota stone slab flooring over 20mm (Average)

27 thick base of cement mortar 1:6 (1-cement : 6-coarse sand) or L.M. 1.1.5 laid over and jointed with grey cement SQM 1,085.48 419.00

slurry including rubbing and polishing etc. complete. (B) 30 mm thick

Polishe Kota Stone Skirting / Riser / vertical : Providing and laying polished kota stone slab 25mm thick in

risers of steps,skirting Dedo and pillars laid on 10mm thick cement mortar 1:3 (1-Cement : 3 coarse sand) and

28 jointed with gray cement slury mixed with SQM 1,176.03 106.00

pigment to match the shade of slab including rubbing and polishing etc. complete.

Vitrified Tile Flooring - polished : P & L 24" x 24" vitrified 8 mm thick tile flooring over 20 mm (average) base of

cement mortar 1:6 ( 1 cement: 6 coarse sand) on new surface or fixing on existing flooring by adhesive material

29 including dismentaling of existing flooring and jointed with color cement slurry including finised with flush pointing SQM 1,261.58 5,183.00

& cleaning the surface etc. complete for shade as per architect/client

Vitrified Tile Flooring - antiskit : P & L 24" x 24" vitrified 8 mm thick tile flooring over 20 mm (average) base of

cement mortar 1:6 ( 1 cement: 6 coarse sand) on new surface or fixing on existing flooring by adhesive material

30 including dismentaling of existing flooring and jointed with color cement slurry including finised with flush pointing SQM 1,383.99 1,129.00

& cleaning the surface etc. complete for antiskit

Vitrified Tile Skirting / Dado / Vertical (Rooms) : Providing and laying Vitrified tiles 8 to 10 mm thick , 24'' x 24''

31 in skrting risers of steps and dedo on 10mm thick cement plaster 1:3 (1-cement : 3- coarse sand) and jointed with SQM 1,130.15 3,029.00

white cement slurry

Ceramic Tile Flooring : Providing and laying Ceramic tiles 6mm thick in flooring treads of steps and landing laid

32 on a bed of 12mm thick cement mortar 1:3 (1-cement : 3-coarse sand ) finishing with flush pointing in white SQM 960.47 2,124.00

Ceramic Tile Skirting / Dado / Vertical : Providing and layingCeramic tiles 6mm thick in skrting risers of steps

33 and dedo on 10mm thick cement plaster 1:3 (1-cement : 3-coarse sand) and jointed with white cement slurry SQM 1,028.11 145.00

Item no. Item Description Unit Rate Total Qty. Amount

Granite Skirting / Riser / vertical - Polished : Providing and laying GRANITE STONE SLAB 25mm thick in

risers of steps,skirting Dedo and pillars laid on 10mm thick cement mortar 1:3 (1-Cement : 3 coarse sand) and

34 jointed with gray cement slury mixed with pigment to match the shade of slab including rubbing and polishing etc. SQM 2,511.00 253.00

Granite Treads - Polished : 'Providing and fixing 20mm thick approved up to 600mm wide polish finish Granite

stone treads of length of step and machine cut, machine polished. Treads to be rounded at front and all exposed

edges machine polished. Further treads to have edge polished chamfering with 3 nos. (6mm x 3mm deep)

35 grooves on top at front or as detailed in drawing for antiskid effect as shown in the drawing. Treads fix to be using SQM 4,113.00 319.00

approved adhesive over cement concrete screed joints grouted with approved matching coulour grout,, curing,

cleaning, polishing etc. all complete at all heights and leads to the approval of the Engineer in charge.

Granite Treads - Leather Finish : 'Providing and fixing 20mm thick approved up to 600mm wide leather finish

Granite stone treads of length of step and machine cut, machine polished. Treads to be rounded at front and all

exposed edges machine polished. Further treads to have edge polished chamfering with 3 nos. (6mm x 3mm

36 deep) grooves on top at front or as detailed in drawing for antiskid effect as shown in the drawing. Treads fix to be SQM 3,641.00 50.00

using approved adhesive over cement concrete screed joints grouted with approved matching coulour grout,,

curing, cleaning, polishing etc. all complete at all heights and leads to the approval of the Engineer in charge.

Polished Granite Coping : Providing and fixing premoulded and prefinished, machine cut polished 18-20 mm

thick granite stone for coping, parapet top and similar locations of required size, approved shade, colour and

37 texture laid using approved adhesive over cement concrete screed (paid separately), joints grouted with approved SQM 6,980.00 634.00

matching colour grout, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high

gloss finish etc. complete at all levels, as per sample approved by Engineer in-charge.

Sandwich Kitchen Platform : 'Providing & Fixing Sandwich type Kitchen Platform of Min. 750mm wide using Top

18mm thick granite of approved shade and sample and bottom 25mm thick single side Polished kota stone with

25 mm thick screed of cement mortar 1:3 With granite Facia Patti. and vertical End granite supports. The stone

38 shall be fixed by chassing in to the wall surface and supported vertically with 25mm thick sandwich kota stone SQM 3,159.00 360.00

support to complete job as directed by Architect/Engineer -in-charge. It is inclusive of all necessary chasses &

civil work, holes and cuts etc. comp. No extra payment shall be made in any case.

Toilet Wash Basin Counters - Providing & Fixing Granite wash basin counter of granite of Min. 600mm wide

using Top 18mm thick granite having drop facia with epoxy adhesive to 25mm tk. marine play wood along the

platform as per typical details given in. ref. drawing of approved shade and sample. It allows for all necessary

39 mirror polish moulding, edge polishing, chamfering, etc. completed. Necessary arrangement of MS SQM 4,418.00 332.00

50mmx50mmx2mm customized bracket fixed to given wall to support granite top shall be part of this item. It is

inclusive of all necessary chasses & civil work, holes and cuts etc. comp. No extra payment shall be made in any

Granite Urinal Partitions : Providing and fixing stone slab with table rubbed, edges rounded and both side

polished, of size 450x900 mm deep and 40 mm thick, fixed in urinal partitions by cutting a chase of appropriate

40 width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 SQM 1,793.00 3.00

cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge

and finished smooth.Granite Stone of approved shade

Item no. Item Description Unit Rate Total Qty. Amount

Providing and fixing pre-cast Rubber Dye / steel Dye inter locking concrete block 60mm thick with grade of

concrete M300 pnumatic compressed / vibrated mechanically and as per approved design Confirming to IS

41 : 2006 including 35 mm Sand layer for levelling and filling the joint with sand in proper line and level as per SQM 680.10 1,241.00

guidlines of IRC : SP 63-2018 etc. Complete.

Providing and fixing pre-cast concrete kerbstone of gray cement based concrete block 30cm

42 length,30cmheightand15cmthickofM200grade concret as per approved design and including excavationfor fixing RMT 376.43 527.00

inproper lineandlevel,filling the jointwithC:M1:3 (1cement:3fine sand) etc complete.

Providing and laying cushioning layer on R.C.C. Slab consisting of 75mm thick lime, concrete using brick

aggregate of 20mm nominal size mortar compresing of 1-Lime : 2- fine sand)

TOTAL OF FLOORING & PAVING WORK

E PAINTING AND POINTING

Wall painting (two coats) with plastic emulsion paint of approved brand and manufacture on undecorated wall

44 surface to give an even shade including throughly brushing the surface free from mortar droppings and other SQM 78.44 19,336.00

foreign matter and sand papered smooth.

Finishing wall with water proofing cement paint of on wall surfaces (Two coats) to give an approved brand and

45 manufacture and of required shape even shade after thoroughly brushing the surface to remove all dirt and SQM 63.34 10,500.00

remains of loose powered materials. + for finishing with cement paint on ceiling and sloping roofs.

Applying two coats of putty & two coats of primer of approved brand and manufacture on new wall surface to give

46 an even shade including thoroughly brushing the surface free from mortar dropping and other foreign matter and SQM 40.19 29,836.00

sand papered smooth.

Exterior Texture Paint : Providing and applying exterior textured paint system on prepared surfaces, comprising

47 1 coat primer, 2 coats textured finish, and 2 coats clear protective top coat, including all materials, labour, surface SQM 164.00 23,385.00

preparation, scaffolding, and complete as per specifications.

White washing with lime on wall surface (onecoats) to give an even shade including thoroughly booming the

surface to remove all dirt, dust; mortar drops and loose scales of lime washand other foreign matter.

Metal surface primer+paint : Applying priming coat over new steel and other metel surface after and including

preparing the surface by throughly cleaning, oil,grease, dirt and other foreign matter and scoured with brushes

fine steel wood, scrapers and sand paper with ready mixed priming paint brushing red lead. Painting two coats

(excluding priming coat) on new steel and other metal surface with enamel paint, brushing, interior to give an even

49 shade including cleaning the surface an even shade including cleanicn the surface of all dirt, dust and other SQM 121.28 1,120.00

foreign matter. Painting two coats (excluding priming coat) on new steel and other metal surface with enamel

paint, brushing, interior to give an even shade including cleaning the surface an even shade including cleanicn

the surface of all dirt, dust andother foreign matter

TOTAL OF PAINTING AND POINTING WORK

F CEILING & PARTITION WORK

Item no. Item Description Unit Rate Total Qty. Amount

GYPSUM BOARD CEILING : Providing and fixing suspended false ceiling at all heights using a galvanized steel

framework with ceiling drop up to 1000 mm, designed to satisfy L/400 deflection criteria under 200 Pa load. The

ceiling shall comprise single layer 12.5 mm thick tapered edge gypsum board conforming to IS 2095 (Part 1):2023

Type A / EN 520 Type A or equivalent approved standards, consisting of aerated gypsum core encased in and

firmly bonded to paper liners, having required thermal and mechanical properties.

The framework shall be made of galvanized steel sections conforming to relevant standards, manufactured from

CR1 grade steel with minimum yield strength of 300 MPa and appropriate corrosion protection (minimum 120 522.00

GSM or equivalent coating), including perimeter channels fixed along walls/partitions at specified intervals using

approved fasteners suitable for the substrate, ceiling angles suspended from the soffit using cleats and anchors,

intermediate channels, and ceiling sections fixed at required spacing to form a rigid grid.

The gypsum boards shall be fixed to the framework using suitable drywall screws at specified spacing. All joints

shall be treated with approved jointing compound and jointing tape, finished in multiple layers to achieve a

smooth, seamless surface ready to receive paint.

The work shall include making necessary cut-outs and providing framing for light fixtures, diffusers, grills and

other services, complete in all respects as per approved drawings and directions of the Engineer-in-Charge.

The item shall include all materials, labour, scaffolding, tools and tackles, all leads and lifts, complete, but

excluding final painting.

MOISTURE RESISTANT GRID CEILING :Providing and fixing tiled false ceiling in true horizontal level using

600x600 mm grid system with hot-dip galvanized steel sections, comprising main runners (~24x38x0.3 mm) at

1200 mm c/c, cross tees (~24x25x0.3 mm) at 600 mm c/c and secondary tees forming 600x600 mm grid,

supported on GI wall angles (~24x24x0.4 mm) fixed along periphery. The framework shall be suspended from

soffit using cleats, hangers and approved fasteners at specified spacing, ensuring proper alignment and level. All

sections shall be of galvanized steel conforming to relevant standards with minimum 90–120 GSM coating.

The grid shall accommodate 12–12.5 mm thick square edge gypsum/plasterboard tiles of size 595x595 mm

conforming to IS 2095 or equivalent, factory laminated with decorative/facing finish and sealed edges, laid in the

grid to form a uniform ceiling. The system shall include all necessary supports, hangers, fasteners and

accessories, complete in all respects as per drawings and directions of the Engineer-in-Charge.

GYPSUM GRID CEILING : Providing & Fixing of Soft Fibre Acoustical Suspended Ceiling System with Optra

Beveled Tegular Edge Tiles With Armstrong Silhouette 15mm Exposed Grid. The tiles should have Humidity

Resistance (RH) of 95%, NRC 0.9, Light Reflectance ≥85%, Colour White, Fire Performance UK Class 0 / Class

1 (BS 476 pt - 6 &7) in module size of 600x600x15mm, suitable for Green Building application, with Recycled

content of 66% GW & 74% RW. The tile shall be laid on Armstrong Silhouette profile grid system with 15mm

white flanges incorporating a 6mm central reveal in white/black colour and with a web height of 38mm and a load

carrying capacity of minimum 7.90 Kgs/M2 (as per standard installation layout mentioned below) & pull out

strength of 100Kgs. Silhouette, Main Runners & Cross Tees to have mitred ends & “birdsmouth” notches to

provide mitred cruciform junctions. The T Sections have a Galvanizing of 90 grams per M2 and need to be

52 installed with Suspension system of Armstrong make. SQM

Item no. Item Description Unit Rate Total Qty. Amount

The Tile & Grid system used together should carry a 10 year warranty.ARMSTRONG SUSPENSION SYSTEM

accessories manufactured and supplied by Armstrong World Industries consisting of M6 Anchor Fasteners with

hanger hole, pre Straightened Hanger wire of dia – 2.5 mm of 1.80 m length having a tensile strength of 344-413

MPa and a minimum pull strength of 110 kgs. (Adjustable hook clips of 0.7mm thick, galvanized spring steel can

also be used for installation purpose as an additional accessory. The adjustable clip also consists of a 4 mm

aquiline wire to be used with the main runner).Hanging system up to 1.5 M (for above mentioned item)

Cement Board False Ceiling - Designing, Fabricating, testing, installing and fixing of Heavy-duty GI Sections,

8mm thk. Cement fibre sheet fixed with self-tapping screw, keeping 3-4 mm gaps at every joint. Acrylic Sealant

53 will be applied to all cement board joints. All the joints are treated with 150 mm-wide 160 GSM Fibre Mesh and SQM 2,440.00 78.00

Styrobond DP. Terabond A (Mixing Ration with water 1:5) will be applied to the cement board. Finish TOP Coat -

Exposed Concrfete Finish Decorend will be applied in two layers.

TOTAL OF CEILING AND PARTITION WORK

G WATER PROOFING WORK

RAFT: Supplying and installing waterproofing treatment for Raft/Grade slab by using fully bonded HDPE sheet,

membrane 1.2mm thick before casting of the RCC Raft.

The preapplied, fully bonded HDPE sheet membrane to get bonded to the underneath of the poured concrete

used as base/ raft slab to resist lateral water migration. The fully bonded HDPE sheet membrane shall consist

of a thick HDPE film, a highly aggressive pressure sensitive adhesive and Granuels which bonds integrally to 3,026.00

poured concrete of base slab.

The membrane shall conforms to basement waterproofing protection to grade 3 as defined in BS 8102:2009. The

fully bonded HDPE sheet waterproofing membrane shall have following minimum properties :

1) Resist hydrostatic pressure of - 60 +/- 6 m head of water (as per ASTM D5385)

2) Peel Adhesion to concrete- Minimum 1.5 N/mm

3) Puncture Resistance – 800 +/- 100 N

4) Tensile strength -21 +/- 3 N/mm2

54 5) Engloation :400% SQM

6) Bare HDPE Thickness > 0.8 mm

7) Joint Strength at overlap - 15 +/- 2 N/mm

The fully bonded HDPE sheet membrane shall be installed with heat welded method by accurately positioning

sheets by overlapping them for 100 mm. The membrane shall be laid over the concrete blinding having smooth

dried surface including necessary removal of release liner while applying, necessary overlaps between the

membranes and fixing overlaps by Double sided adhesive tape firm rolling onto the surface to get a tight seal,

etc. Hot applied materials or protective screed shall NOT be permitted. All systems to be installed as per

manufacturer's recommendations, etc. complete with all lead and lift for all materials and labour and as directed

by Engineer in-charge.

This membrane shall be terminated Horizontally and fixed using EVA at the junctions/ pheriphary of the basement

wall & Raft as per Manufacturers recommendation, including all materials & labour, etc, all complete.

Item no. Item Description Unit Rate Total Qty. Amount

Retaining Wall Waterproofing :

Surface preparation: The substrate must be free of loose aggregate, slush, mud, sharp protrusions and stagnated

water. Ground water level needs to be kept under the PCC level, continues dewatering to be done till completion

of concreting. The surface of retaining wall should be dry (moisture content <5%) before application of

primer.Construction Joint treatment: All the construction joints in retaining wall should be opened in a V groove

manner of size 10mm X 10mm using a grinder or suitable tool & should be sealed with Polymer Modified Mortar

prepared with ReArm Bond SBR 45 or equivalent @5 liter per 50 kg bag of cement.

Filling of tie rod holes: The tie rod holes shoukd be filled with Polymer modified mortar prepared using ReArm

Bond SBR 45 or equivalent @5 liter per 50 kg bag of

Preparation of chamfer or vatta at wall & raft junction: The junction between RCC raft & retaining wall should be

treated by preparation of vatta of size min. 50mm X 50mm with Polymer Modified Mortar prepared ReArm Bond

SBR 45 or equivalent @5 liter per 50 kg bag of cement.

Application of primer: Bituen based Primer should be applied on treated, dry concrete surface at coverage of 4 to

6 SQM per liter using a brush or roller. Primer should be allowed to dry for minimum 2 hrs. The SBS membrane

should be fixed within 24 hours after application of primer.

SBS Membrane: Supplying and applying waterproofing of RCC Retaining wall using High performance, self

adhesive membrane with cross laminated HDPE film AquaArm SBS 3000 X or equivalent,conforming to BS

8102 & IS 16471 as per the specifications listed below - Puncture Resistance: 300 N (as per ASTM E 154) and

Hydrostatic Head Resistance: not less than 70 m head (ASTM D 5385), Tensile Strength - 4.0/3.5 N/mm² (ASTM

D 412) ,Elongation of > 230 % (ASTM D 412), Low Temperature Flexibility up to: -15°C. The SBS membrane

should be fixed on the primed concrete surface by removing the release film with maintaining overlap of 75 mm at

the sides & 100 mm at the end sections.'

Protection of membrane: The SBS Membrane should be protected by means of 6-8 mm thick dimple boards

against any physical damage before commencement of backfilling.

Termination of Membrane on retaining wall: The SBS membrane should be secured with a Metal strip on

retaining wall (300 mm above the ground level) used in conjunction with polyurethane sealant between the

56 membrane and Metal Strip. The termination bar / Metal strip must be installed directly into the wall width and RMT 291.00 272.00

mechanically fixed at c/c using appropriate fasteners. A bead of Sealant is applied along the top edge of the

termination bar.

TERRACE WATERPROOFING : Surface Preparation: Providing and laying water proofing treatment to

horizontal and vertical surfaces of concrete, including cleaning the surface with wire brush, treating all

surface cracks, construction joints and honeycombs by grouting with specialised non shrink grout,coving

preparation at wall - slab joint and preparation of surface in all aspects to receive the waterproofing.

Item no. Item Description Unit Rate Total Qty. Amount

Injection Grouting (If required): Providing Chemical injection treatment in the form of pressure grouting to the

cold joint by injecting cement slurry mixed with grout admixture ArmGrout Additives @ 250 gms.per bag of

cement, in the required consistency through the pre fixed PVC nozzles in the 10mm dia holes, fixing of PVC

nozzles with quick setting compound ReArm Fix 10S of MYK Arment or equivalent and final cutting the projected

nozzles and sealing off the PVC nozzles after the injection operation is over with quick setting compound , no

shrink rapid setting mortar compound, finishing, curing etc. as per manufacturers specification and as directed.If

any lekages found in pre

ponding then this need to be done.

Coving: Providing and Applying at the junction of slab and vertical offsets with Cement Mortar 1:4 and admixed

with SBR polymer at dosage of 5Ltr per 50kg cement.

Application of Primer: Apply Epoxy based primer over well prepared surface at 200-400 gm per SQMr.

Application of Polyurethane waterproof coating: Providing and applying Two coats of liquid applied single

component polyurethane based waterproofing system . It has to be applied @1.95 kg/SQMr to achieve a

thickness of 1.2 mm in two coats.The membrane will have the following technical parameters: Tensile Strength :

2 N/mm² ,. Elongation at break : 400% , Adhesion To concrete: >1.5 N/mm²

Providing and laying 150 Gsm Geo fabric membrane as separation layer

Protection Screed:Horizontal Areas: Providing and Laying M25 grade screed concrete in 1:100 to a average

thickness of 100 mm mixed with Integral Waterproofing admixture at the dosage of 125 ml/bag of cement over

waterproofing layer to a minimum thickness of 75 mm as per site requirement including control joints of 4M X 4M

size and filling the panels with polyurethane sealant.

Item no. Item Description Unit Rate Total Qty. Amount

WET AREA (Kitcen, Toilets, Wash Area) : Surface Preparation: Providing and laying water proofing treatment

to horizontal and vertical surfaces of concrete, including cleaning the surface with wire brush, treating all

surface cracks, construction joints and honeycombs by grouting with specialised non shrink grout,coving

preparation at wall - slab joint and preparation of surface in all aspects to receive the waterproofing.

Injection Grouting (If required): Providing Chemical injection treatment in the form of pressure grouting to the

cold joint by injecting cement slurry mixed with grout admixture @ 250 gms.per bag of cement, in the required

consistency through the pre fixed PVC nozzles in the 10mm dia holes, fixing of PVC nozzles with quick setting

compound and final cutting the projected nozzles and sealing off the PVC nozzles after the injection operation is

over with quick setting compound , no shrink rapid setting mortar compound, finishing, curing etc. as per

manufacturers specification and as directed. If any lekages found in preponding then this need to be done.

Coving: Providing and Applying at the junction of slab and vertical offsets with Cement Mortar 1:4 and admixed

with SBR polymer at dosage of 5Ltr per 50kg cement.

Waterproofing Coating-Providing and application of a two component, cementitious acrylic polymer based

high performance water proofing coating. It offers seamless coating applied@ 2 Kg /SQM for 2 coats @

mm DFT .Technical Data: Inter coat application time, Hrs 2-3, Tensile strength (ASTM D 412) >2 N/mm²

Elongation at break (ASTM D 412)

>175%, Adhesion strength (ASTM D 4541) >1.2 N/mm², Crack bridging (ASTM C 836) pass up to 2 mm.

Toilet Sunk Filling : (not applicable for toilets with underslung plumbing) :

Providing and filling sunken area with Light Weight Block bat (40-60 mm) with cement mortar mixed in ratio 1:3:6

(1 cement : 3 sand : 6 brick bats) including mixing of water proofing compound 4 % by weight of cement to sunk

portions of toilets to the entire satisfaction of the PM. Toilet / Sunk portion shall be tested by ponding water for

WATER RETAINING STRUCTURES (UGT & OHT) : Surface Preparation: Providing and laying water proofing

treatment to horizontal and vertical surfaces of concrete, including cleaning the surface with wire brush, treating

all surface cracks, construction joints and honeycombs by grouting with specialised non shrink grout,coving

preparation at wall - slab joint and preparation of surface in all aspects to receive the waterproofing.

Injection Grouting (If required): Providing Chemical injection treatment in the form of pressure grouting to the

cold joint by injecting cement slurry mixed with grout admixture @ 250 gms.per bag of cement, in the required

consistency through the pre fixed PVC nozzles in the 10mm dia holes, fixing of PVC nozzles with quick setting

compound and final cutting the projected nozzles and sealing off the PVC nozzles after the injection operation is

over with quick setting compound , no shrink rapid setting mortar compound, finishing, curing etc. as per

manufacturers specification and as directed.If any lekages found in pre ponding then this need to be done.

Coving: Providing and Applying at the junction of slab and vertical offsets with Cement Mortar 1:4 and admixed

with SBR polymer at dosage of 5Ltr per 50kg cement.

Item no. Item Description Unit Rate Total Qty. Amount

Protective Plaster: providing and laying avg. 15 mm thick, CM 1:4 plaster admixed with Integral Waterproofing

Compound @ 150 ml / bag of cement at Vertical Walls. Food Grade epoxy coating- Application of food grade

epoxy coating in Inner side of tank: providing and applying CFTRI Certified epoxy coating applied @

kg/m2 in two coats. It will give 400 microns thickness. Pot life: 30 Minutes at 25°C ,20 Minutes at 30°C,Mixing

Ratio, by Weight: 100(Base):38(Hardener), Touch dry: 4 Hours at 30ºC, Re coatable: 12 -18 Hours at 30ºC, Open

to foot traffic: 24 Hours at 30ºC, Final cure: 7 Days at 30ºC, Adhesive bond strength to concrete, (ASTM D 4541):

>1.5 MPa (concrete failure)

WATERPROOFING FOR PODIUM WITH HARDSCAPE : Surface Treatment: Providing and laying water

proofing treatment of terrace including cleaning the surface with wire brush, treating all surface cracks,

construction joints and honeycombs by grouting with specialised non shrink grout and preparation of surface in all

aspects to receive the waterproofing.

Coving: Providing and Applying at the junction of slab and vertical offsets with Cement Mortar 1:4 and admixed

with SBR polymer ReArm Bond SBR 45 of MYK Arment or equivalent at dosage of 5Ltr per 50kg cement.

Application of primer: Providing and applying Epoxy based primer FloArm Primer PUDC of MYK Arment or

equivalent over well prepared surface at 200-400 gm per Sq.Mtr.

Application of Polyurethane waterproof coating: Providing and applying Two coats of liquid applied single

component polyurethane based waterproofing system AquaArm SPU-SPL of MYK Arment or equivalent . It has

60 to be applied @1.95 kg/sqmtr to achieve a thickness of 1.2 mm in two coats.The membrane will have the SQM 2,440.00 2,489.00

following technical parameters: Tensile Strength : 2 N/mm2 ,. Elongation at break : 400% , Adhesion To concrete:

Providing and laying 150 Gsm Geo fabric membrane as separation layer

Protection Screed:Horizontal Areas: Providing and Laying M25 grade screed concrete in 1:100 to a average

thickness of 100 mm mixed with Integral Waterproofing admixture AquaArm Prufe IWP 10 of MYK Arment or

equivalent at the dosage of 125 ml/bag of cement over waterproofing layer to a minimum thickness of 75 mm as

per site requirement(Civil Contractor Scope) including control joints of 4M X 4M size and filling the panels with

polyurethane sealant.

WATERPROOFING FOR PODIUM WITH SOFTSCAPE : Surface Treatment: Providing and laying water proofing

treatment of podium including cleaning the surface with wire brush, treating all surface cracks, construction joints

and honeycombs by grouting with specialised non shrink grout and preparation of surface in all aspects to receive

the waterproofing.

Coving: Providing and Applying at the junction of slab and vertical offsets with Cement Mortar 1:4 and admixed

with SBR polymer ReArm Bond SBR 45 of MYK Arment or equivalent at dosage of 5Ltr per 50kg cement.

Application of primer: Providing and applying Epoxy based primer FloArm Primer PUDC of MYK Arment or

equivalent over well prepared surface at 200-400 gm per Sq.Mtr.

Application of Polyurethane waterproof coating: Providing and applying Two coats of liquid applied single

component polyurethane based waterproofing system AquaArm SPU-SPL of MYK Arment or equivalent . It has

to be applied @1.95 kg/sqmtr to achieve a thickness of 1.2 mm in two coats.The membrane will have the

following technical parameters: Tensile Strength : 2 N/mm2 ,. Elongation at break : 400% , Adhesion To concrete:

Item no. Item Description Unit Rate Total Qty. Amount

Providing and laying 150 Gsm Geo fabric membrane as separation layer

Protection Screed:Horizontal Areas: Providing and Laying M25 grade screed concrete in 1:100 to a average

thickness of 100 mm mixed with Integral Waterproofing admixture AquaArm Prufe IWP 10 of MYK Arment or

equivalent at the dosage of 125 ml/bag of cement over waterproofing layer to a minimum thickness of 75 mm as

per site requirement including control joints of 4M X 4M size and filling the panels with polyurethane sealant.

Dimple Board for Protection of membrane before Backfilling:

Providing and applying Extruded Polystyrene Protection Board of approved make and around 8 mm thick and

shall be laid down to the membrane and then soil filling can be done as per manufacturer's recommendation.

TOTAL OF WATERPROOFING WORK

H DOOR AND WINDOW WORK

FLUSH DOOR (SINGLE / DOUBLE LEAF) WITHOUT HARDWARE WITHOUT LOUVERS : Providing and fixing

35 mm thick pre-laminated (1mm) hinged door made out of 150mm x 70mm cp-sag indian teak wood outer frame

with holdfast and shutters made of 35 mm thick facory fabricated flush door including concealed lipping

(35mmx6mm-matt malamine polished to exposed surface) to receive hinges. colour and shade for laminates shall

62 be as architect. All necessaty carpentery and civil work to fix in true line & level, plumb at all level shall be part of SQM 5,233.00 1,270.00

contractor and commissioned as directed by EIC. Hardware shall be paid extra under relavent item. It is inclusive

of matt melamine polish (1 coat sealer + minimum 2 coat matt mellamine polish) with sanding, rubbing, etc.

For single / double leaf shutter without hardwares without louvers

FLUSH DOOR (SINGLE LEAF) WITHOUT HARDWARE WITH LOUVERS : Providing and fixing 35 mm thick pre-

laminated (1mm) hinged door made out of 150mm x 70mm cp-sag inidan teak wood outer frame with holdfast

and shutters made of 35 mm thick facory fabricated flush door including concealed lipping (35mmx6mm-matt

malamine polished to exposed surface) to receive hinges. colour and shade for laminates shall be as architect. All

63 necessaty carpentery and civil work to fix in true line & level, plumb at all level shall be part of contractor and SQM 5,644.00 11.00

commissioned as directed by EIC. Hardware shall be paid extra under relavent item. It is inclusive of matt

melamine polish (1 coat sealer + minimum 2 coat matt mellamine polish) with sanding, rubbing, etc. complete

Do as above for single leaf with louvers without hardwares

HARDWARE FOR DOORS :

HINGE FOR ALL FLUSH DOORS : dormakaba 3043F, 5 Knuckle, 2 Ball bearing butt hinges size 4" x 3" x 3mm,

Material: SS 304, Finish: Satin Stainless Steel (SSS). Suitable for Wooden door weight up to 120kgs, Grade

64 Template Drilled. Approved to EN 1935, Fire-rated, Square Corners, Durability - 200,000 Cycles, Corrosion Nos. 273.00 1,992.00

Resistance - Very High

MORTICE SASH LOCK FOR REGULAR DOORS : dormakaba Mortice sash lock 271a with 55mm backset,

20mm square forend with 72 mm centers and prepared for euro profile cylinder including strike plate in satin

65 stainless steel as per EN 12209, Durability - 200,000 Cycles, Load on Latch Bolt - 50N , Door mass - 200 kg, Nos. 1,599.00 196.00

Corrosive resistance - Very High ( - 20 C to +80 C)

MORTICE SASH LOCK FOR TOI. DOORS : dormakaba Mortice WC lock 275a with 55mm backset, 20mm

square forend with 78 mm centers and prepared for 8mm bathroom follower including strike plate in satin

66 stainless steel as per EN 12209, Durability - 200,000 Cycles, Load on Latch Bolt - 50N , Door mass - 200 kg, Nos. 1,598.00 261.00

Corrosive resistance - Very High ( - 20 C to +80 C)

Item no. Item Description Unit Rate Total Qty. Amount

MORTICE DEAD LOCK : dormakaba Mortice dead lock 278a with 55mm backset, 20mm square forend,

prepared for euro profile cylinder including strike plate in satin stainless steel as per EN 12209, Durability -

67 200,000 Cycles, Load on Latch Bolt - 50N , Door mass - 200 kg, Corrosive resistance - Very High ( - 20 C to +80 Nos. 1,581.00 15.00

LOCK PROFILE FOR DEAD LOCK : dormakaba Mortice dead lock 278a with 55mm backset, 20mm square

forend, prepared for euro profile cylinder including strike plate in satin stainless steel as per EN 12209, Durability

68 - 200,000 Cycles, Load on Latch Bolt - 50N , Door mass - 200 kg, Corrosive resistance - Very High ( - 20 C to +80 Nos. 459.00 15.00

EURO PROFILE CYLINDER - BSK (Both Side Key) : dormakaba DEC 6 Plus 60, 6 pin Euro profile cylinder with

69 inline brass keys. Master keyed system included as per client requirement. Nos. 1,997.00 183.00

External & Internal key operation. Length: 60mm

EURO PROFILE CYLINDER - KT (Key + Thumbturn) : dormakaba DEC 6 Plus 60T, 6 pin Euro profile cylinder

70 with inline brass keys. Master keyed system included as per client requirement. Nos. 2,168.00 112.00

External key & Internal thumb turn operation. Length: 60mm

EURO PROFILE CYLINDER - CT (Coin + Thumbturn) for Toilets : dormakaba 3016, 6 pin Euro profile knob

71 cylinder with internal thumb turn and external coin operation standard length 60mm in satin nickle plated finish. Nos. 1,476.00 177.00

NMK.Durability: 100,000 Cycles

LEVER HANDLE (PAIR): dormakaba Pure Lever handle 8906 lever with round roses, escutcheons prepared for

Euro profile cylinder and spindle 114 in satin stainless steel. Complete set including the fixing accessories for

72 50mm thick door. Material:SS 304. Approved to EN 1906 , Durability - 200,000 Cycles, Corrosion Resistance - Nos. 2,639.00 452.00

LEVER HANDLE WITH INDICATOR (PAIR): dormakaba Pure 8906 Lever Handle with 6501 Roses,7122 WC

Indicator, 8mm Spindle with Fixing Screws for door thickness 35-55mm, SS 304, Finish : Satin

74 TOWER BOLT : dormakaba 3200-2 Surface Mounted Tower bolt of Length 6" in Satin chrome finish Nos. 474.00 87.00

75 PEEP HOLE : 180° brass/SS, dormakaba equivalent Nos. 748.00 84.00

DOOR CLOSER : dormakaba rack and pinion door closer TS 68 with selectable closing force, size EN 2, 3 and

76 , std. arm adjustable closing speed in two independent ranges. Non-handed. Approved to EN 1154. Durability - Nos. 3,308.00 8.00

500,000 Cycles ,Corrosive resistance - Moderate, Finish:Silver

PULL HANDLE (PAIR) : dormakaba pull Handle TGDI-D 300 back to back with adjustable fixing for glass, wood

77 and metal doors in satin stainless steel. The pull handles should have supporting washer with raised bevelling on Nos. 1,922.00 15.00

the outer surface.CTC - 300mm, 22mm dia, Material - SS304

DEAD BOLT FOR SHAFT FLUSH DOORS : dormakaba Mortice shaft dead bolt with key with BS 57mm and

25mm Sq forend with escutheions in SSS.

OVAL PULL HANDLE FOR SHAFT FLUSH DOORS : dormakaba Recessed Oval Flush Pull Handle 1207, SSS

HARDWARE FOR ADA TOILET DOOR :

ADA TOILET DOOR - HINGES : dormakaba 3043F NRP, 5 Knuckle, 2 Ball bearing butt hinges size 4" x 3" x

3mm with Non-Removable Pin, Material: SS 304, Finish: Satin Stainless Steel (SSS). Suitable for Wooden door

80 weight up to 120kgs, Grade 13, Template Drilled. Approved to EN 1935, Fire-rated, Square Corners, Durability - Nos. 401.00 4.00

200,000 Cycles, Corrosion Resistance - Very High

Item no. Item Description Unit Rate Total Qty. Amount

ADA TOILET DOOR - DOOR CLOSER : dormakaba TS 92 B barrier free access designed cam action door

closer complying to BS 8300 & ADM opening force of below 30N between 0º and 30º degrees and below 22.5N

between 30º and 60º degrees. Complies to CEN 15894 Guidelines of 40% reduced opening force & minimum

65% door closer efficiency. Door closer with G-N slide channel arm for pull side fixing, adjustable closing speed in

two independent ranges. closing force infinitely variable between size EN 1 and EN 4. Non-handed.

Approved to EN 1154 and CERTIFIRE, CE Marked. Durability - 500,000 Cycles, Corrosive Resistance - High.

ADA TOILET DOOR - LOCK : dormakaba Mortice WC lock 375a with 55mm backset, 20mm square forend with

78 mm centers and prepared for 8mm bathroom follower including strike plate in satin stainless steel as per EN

12209, Durability - 200,000 Cycles, Load on Latch Bolt - 120N , Door mass - 200 kg, Corrosive resistance - Very

High ( - 20 C to +80 C)

ADA TOILET - LEVER WITH INDICATOR : dormakaba Pure Lever handle 8100 lever with round roses,

WC Indicator and spindle 114 in satin stainless steel. Complete set with fixing accessories for 50mm thick door.

Approved to EN 1906, Durability - 200,000 Cycles, Corrosion Resistance - Very High

ADA TOILET DOOR - GRAB BAR : dormakaba GBDI D-600 Grab Bar of Length 610mm, 25mm Diameter in

Satin stainless Steel Finish.

METAL DOORS - FIRE RATED (120 Mins)

METAL FIRE DOORS (120 Minutes) with 30 min insulation As per IS3614:

Supply and fixing of Hollow metal fire rated doors as per IS 3614:2021 for stability and integrity with 30minutes

insulation. Pressed Galvanized steel confirming to IS 277 with the following specification. Recommended fire door

shall have doors tested at CBRI /NABL Approved Labs for maximum rating of 2hrs tested . Individual Test

certificates should also be available for glass used in vision lites confirming the required fire ratings /panels being

a part of the fire door assembly. Doors should be finished in Thermosetting Powder Coating desired RAL Shades.

Manufacturer test certificate shall cover doors both single & double leaf doors and Hardware's should pass

European certificate "CE" of conformity / UL with required fire ratings. Any deviation in specification and sheet

thickness other than what is mentioned in the test certificates are not allowed. Proper label confirming the type of

door and the hourly rating is mandatory. Approved manufacturer Navair International or equivalent subject to

architect’s approval. And should be ISO Certified company.

Item no. Item Description Unit Rate Total Qty. Amount

Door frame shall be Single rebate profile of section 100 x 57 mm made out of 1.60mm thick galvanised steel

sheet with a factory pre-punched groove so as to accomodate Fire & smoke seal size 10x4mm . Frames should

be butt jointed and field assembled with bolting system for proper strength .Frames should be provided with back

plate for anchor fasteners (payable extra ) for installation on a finished plastered wall opening.

Door leaf shall be minimum 46mm thick fully flush double skin door with or without vision lite. Door leaf shall be

manufactured from 1.2mm minimum thick galvanised steel sheet. The internal construction of the door should be

rigid reinforcement pads for receiving appropriate hardware. The infill material shall be Rockwool treated with

Viper FRS 881 LH. All doors shall be factory prepared for receiving appropriate hardware and provided with

necessary reinforcement for hinges, locks, and door closers. The edges should be interlocked with a bending

radius of 1.4mm. For pair of doors astragals has to be provided on the meeting stile for both active and inactive

leaf. Vision lite wherever applicable should be provided as per manufacturers recommendation with a beading

and screws from inside.

All doors and frames shall be finished with Powder coating in desired Shades. Once frame installed should be

filled with PUF as recomended by the manufacturer or engineer.

HARDWARE FOR METAL DOORS

SS Ball Bearing Hinges of size 100 x 75x 3mm complete with SS Screws of Becker fs make ( 4 Nos per panel )

87 Door closer overhead STD arm Becker fs make Nos. 2,553.00 45.00

88 Fire glass 6MM Thick 200x300mm Vision Glass from Saint Gobain Nos. 2,128.00 46.00

89 Mortise dead lock with both side key cylinder Becker fs make Nos. 2,502.00 89.00

90 SS Pull handle 300 mm long back to back D type Becker fs make Nos. 1,909.00 89.00

91 Fire seal 10x4mm & smoke seal RMT 299.00 381.00

92 Hilti fasteners 10X 80mm Nos. 64.00 603.00

93 Concealed flush bolt 600mm long for double door Becker fs make Nos. 1,403.00 67.00

Frameless "U" Channel glazing (INTERNAL FIXED GLAZING)

Design, Fabrication, Supply, Installation, Protection, Cleaning & Handover of Frameless glazing system with

Aluminium "U" Channel custom designed to with stand the design wind pressure confirming to IS -875 part III.

(The system must pass the proof test at 2 times design wind pressure without any failure).

The system shall be support the glass at bottom and wind resistance at top by means of continuous U-channel at

the finished floor level and vertically butt glazed with non staining sealant joint between glass to glass. The

weather sealant of approved make, baker rod, SS 304 grade fasteners & hard setting blocks of EPDM, all in

complete required to perform as per specification and drawing in conjunction with BOQ. Complete system shall

94 be warranted for minimum 10 yrs against design & workmanship defects. SQM 4,370.00 121.00

The extruded aluminium sections of Alloy 6063 T5 / T6 & tolerances confirming to DIN / EN standard from

approved extruder. All the visible surfaces shall have high Durability (Akzonobel) / Super durable (Jotun) Powder

coating of 60 - 80 micron.

All Material Make / Vendor list / Supplier list shall be as per tender specification.

All shade approval shall be as per Architect's Approval.

The quote rate shall include all design, engineering & Approval from architect & consultant.

Quote rate for complete system as mentioned above under (B) U-Channel Design in line with Tender drawings for

Ground Floor and First Floor Retail Area, Providing & Fixing Façade 12mm Clear FT Glass.

Item no. Item Description Unit Rate Total Qty. Amount

Frameless Swing Doors_ (Patch Fitting Doors)

Design, Fabrication, Supply, Installation, Protection, Cleaning & Handover Single & Double leaf double swing

patch fitting door made out 12mm thick fully tempered (FT) glass with Dorma make stainless steel patch fittings

for external facade application (PT Series ). Complete with 38mm dia SS handle 1000mm long , PT series patch

fittings, US 10 Door lock at bottom of each shutter and BTS 80, 90 deg with EN 1-4 spring capacity floor spring.

Floor spring covers shall be SS satin finish. as per Architect's approved shop drawings.

Door glass of 12 mm thk clear float fully tempered with holes and notches as per patch fitting requirement. Edges

Machine ground mirror polished. The door glass shall have silicon gasket at bottom to act as weather seal.

All Material Make / Vendor list / Supplier list shall be as per tender specification.

The quote rate shall include all design & shop drawing approval from architect & consultant.

Quote rate for complete system for Frame Less Patch Fitted Door as mentioned above under (C)

1 - Double Leaf Swing Door:- (Size:- 1500mm x 2100mm) with 12mm Thk. Clear FT Glass. Location:- First floor

Internal Portion.

2 - Single Leaf Swing Door:- (Size:- 1000mm x 2100mm) with 12mm Thk. Clear FT Glass. Location:- First floor

Internal Portion.

Aluminium Louvers ( "Y" Type Louvers) System_

Vantilation Lover system - BUILDING FAÇADE AT SHAFTS LOCATION

Design, Fabrication, Supply, Installation, Protection, Cleaning & Handover of Aluminium " Y " shape Louvers

System custom designed to with stand the design wind pressure confirming to IS -875 part III.

Aluminium Louvers shall be made out of 60mm x 36mm x 1.5mm thk. of " Y " shape louvers system spaced at

equivalent distance support to Aluminium frame. Louvers profile shall be fixed on the 3mm thick Al flat to form a

frame. The louver frame is supported on the aluminium box frame with necessary fasteners in SS 316 in line with

97 The extruded aluminium sections of Alloy 6063 T5 / T6 & tolerances confirming to DIN / EN standard from SQM 8,349.00 359.00

approved extruder. The structural profiles shall have minimum 2 mm wall thickness. All the internal & External

visible surfaces shall have Super Durable Powder coating finish of 60-80 micron thickness as per Approved

shade by Architect. The non visible aluminium surfaces shall have mill Finish.

All Material Make / Vendor list / Supplier list shall be as per tender specification.

All shade approval shall be as per Architect's Approval.

The quote rate shall include all design & shop drawing approval from architect & consultant.

Quote rate for complete Aluminium "Y" Type Louvers system as mentioned above under (F)

Aluminium "Y" Type Louvers system_Vantilation Louver System, Location:- Staff Qtrs exterior face shafts

Sliding Window - 4 track : Providing and fixing extruded aluminum window having extruded aluminum Colour

Powder Coated section frame main outer size 127mm x 38.10mm x 1.35mm ,@ Wt.1.384 Kg/mt,horizontal Four

track member size 122.20mm x 31.75mm x 1.10mm @ Wt. 1.205 Kg/mt,vertical member of size 122.20mm x

31.75mm x 1.50mm ,@ Wt. 1.398 Kg/mt with sliding shutters of horizontal member size 40mm x 18mm x 1.29mm

98 @ wt.of 0.456Kg/mt,vertical member of size 40mm x 18mm x 1.29mm @ wt.of 0.456Kg/mt,@ with 5 mm thick SQM 2,119.14 11.00

transparent bronze colour tinted float glass with powder coated aluminum fittings and fixtures and transparent

silicon sealant glass fixing to frame as per details etc complete for window.

Item no. Item Description Unit Rate Total Qty. Amount

Sliding Window - 3 track : Providing and fixing window having extruded aluminum Colour Powder Coated

section frame main outer size 95mm x 24mm x 1.17mm @ wt.of 0.738 Kg/mt, horizontal Three track member size

92mm x 31.75mm x 1.30mm @ Wt.1.07 Kg/mt, vertical member of size 92mm x 31.75mm x 1.50mm ,@ Wt.

99 Kg/mt with sliding shutters of horizontal member size 40 mmx18mm x1.29mm @ wt.of 0.456 Kg/mt, vertical SQM 1,576.11 815.00

member of size 40mm x 18mm x 1.29 mm @ wt.of 0.456Kg/mt with 5 mm thick transparent bronze colour tinted

float glass with powder coated aluminum fittings and fixtures and transparent silicon sealant glass fixing to frame

as per details etc

Sliding Window - 2 track : Providing and fixing window having extruded aluminum Colour Powder Coated

section frame main outer size 63.50 x 38.10 x 1.95 mm,@ Wt 1.094 Kg / Rmt, horizontal two track member size

1.85 mm x 31.75 mm x 1.20mm @ wt.of 0.695 Kg/mt, vertical member of size 61.85 mm x 31.75mm x 1.30 mm @

100 wt.of 0.0.659 Kg/mt with sliding shutters of horizontal member size 40mm x 18mm x 1.29mm @ wt.of 0.456Kg/mt, SQM 1,688.78 206.00

vertical member of size 40mm x 18mm x 1.29mm @ wt.of 0.456Kg/mt with 5 mm thick transparent bronze colour

tinted float glass with powder coated aluminum fittings and fixtures and transparent silicon sealant glass fixing to

frame as per details etc complete for window

VENTILATION : Design, Fabrication, Installation, Protection, Cleaning and Handover of Alum. Glass Louver

windows with exhaust Fan fixing Provision in Toilet areas with hardware's and accessories.

The extruded aluminium sections of Alloy 6063 T5 / T6 & tolerances confirming to DIN / EN standard from

approved extruder. All the internal visible surfaces shall have high Durability (AkzoNobel) / Super durable (Jotun)

Powder coating of 60 - 80 micron confirming to AAMA 26043. The non visible aluminium surfaces shall have

minimum chromatizing treatment.

All Material Make / Vendor list / Supplier list shall be as per tender specification.

All shade approval shall be as per Architect's Approval.

The quote rate shall include all design & shop drawing approval from architect & consultant.

Quote rate for complete Glass Louvers system as mentioned above under :

Ventilation Windows (V1) Bottom Glass Louvers With Top Fix :- SQM 3,422.00 30.00

Top Fix:- 6mm Thk. Frit Glass SQM 3,422.00 30.00

Glass Louvers:- 5mm Thk. Frit Glass @30mm C/C SQM 3,422.00 30.00

ALUMINIUM FIXED WINDOW / Top/side HUNG OPENABLE (OUT) :

Design, Fabrication,Supply,All Material & Site Testing, Protection, Handover of Alum. Fix / Top/Side Hung

102 openable windows system custom designed to with stand the design wind pressure confirming to IS -875 part III.

The system shall have two barrier gasket system for weather sealing. Provision for drainage of uncontrolled water

entering to 1st barrier gasket.

Top/Side hung openable window system shall be including malti-point locking (Min.two) with Handle, projected

type hinges with restrictor arm of approved make, Microwave cured EPDM gaskets. window shutter profile to

accommodate the 6mm SGU HS glass, weather sealants, SS 316 grade screws and fasteners of approved

make, all in complete required to perform as per specification and drawing in conjunction with BOQ.

The extruded aluminium sections of Alloy 6063 T5 / T6 & tolerances confirming to DIN / EN standard from

approved extruder. All the internal visible surfaces shall have high Durability (AkzoNobel) / Super durable (Jotun)

Powder coating of 60 - 80 micron confirming to AAMA 26043. The non visible aluminium surfaces shall have

minimum chromatizing treatment.

All Material Make / Vendor list / Supplier list shall be as per tender specification.

All shade approval shall be as per Architect's Approval.

Item no. Item Description Unit Rate Total Qty. Amount

The quote rate shall include all design & shop drawing approval from architect & consultant.

Quote rate for complete Aluminium Windows system as mentioned above under (F) With 6mm Thk. HS

Glass in line with tender drawing.

Providing and fixing a Top/Side Hung Openable vent With 6mm Thk. HS Glass . SQM 6,182.00 83.00

Providing and fixing a Fix Windows With 6mm Thk. HS Glass. SQM 5,089.00 37.00

Providing and fixing rolling shutters of approved make made of 80 mm wide M.S. laths inter-locked together

through their entire length and jointed together at the ends by end locks mounted on specially designed pipe shaft

103 with bracket plates, guide channels and arragements for inside and outside locking with push-pull operation SQM 3,468.72 30.00

including the cost of hood cover and spring etc. complete. (B) Shutters having width 3.5 M. and above

104 Providing and fixing 27.5 cm. long wire spring grade No.2 of approved make for rolling shutters. EACH 630.91 4.00

Providing and fixing Hood cover for rolling shutters (B) Shutters having width 3.5 meters and above

TOTAL OF DOORS AND WINDOWS

J MISCELLENEOUS

Pre construction Anti termite Treatment : Providing and injecting pre-constructional anti-termite treatment as

per IS:6313 (Part-II) to the RCC members in immediate contact with soil upto a min depth of 500 mm measured

from made up ground level by treating all four sides at the rate of 7 Lit/Sqm of an emulsion in water of 0.5 %

Chloripyrofos 20 EC or equivalent, treating the top surface of plinth filling and the external peripheri of the building

by drilling the holes up to 75 mm deep at 150 mm c/c distance bothways using 12 mm dia ms rod on the surface

to facilitate saturation of the soil with the chemical emulsion at the rate of 5 Lit/Sqm of surface area of an emulsion

in water of 0.5 % Chloripyrofos 20 EC or equivalent. The contractor shall furnish 10 years guarantee for termite

free structure. (Plan area at ground floor level shall be measured for payment.)Notes:1) Allow for Min. of 10 years

gaurantee as described under detailed specifications. 2) Only single time Plinth area shall be measured for

payment, deducting open to sky shafts,verandah etc. for all kinds of buildings i.e. building having basements or no

Toilet Cubicals : Providing and fixing toilet cubical systems of approved make and manufactured in standard

dimensions of 600mm ± 10mm width door size with 12mm thick solid Compact Laminate panels made of KRAFT

paper impregnated with Phenolic resins under high pressure and temperature, including doors, pilasters &

intermediate panels, which should be resistant to heat, bacteria, water, chemical, scratch and impact. Finished

product should be as per approved texture, shade & drawing, detailing and developed according to IS-2046 and 19.00

BS-476/97 standards. The toilet cubicle setup shall include necessary hardware fittings, made out of stainless

steel (Grade-304), as per manufacturer’s specifications and approved by Engineer-in-charge.

Hardware fittings should consist of (1) Stainless steel Adjustable foot/ pedestal of SS 316 grade to give 150mm

clearance from bottom and of weight not less than 600grams (2) Stainless steel U-channels of 20 gauge and 12 x

20mm size (3) Stainless steel Top rail pipe (OD:24mm of 18 gauge) with corner connectors (4) Stainless Steel

Head Rail Tubular Holder (5) Stainless steel Gravity hinges (3 nos.) not less than 75mm length and weight not

less than 210 grams of weight not less than 200 grams. (6) Stainless steel Coat hook with nylon door stopper (7)

Stainless steel Door knob (8) Stainless steel Baby latch (9) Wall bracket SS 304 (10) Corner Connector (11)

Rubber noise deafening tape (12) Stainless steel 304 Screws and PVC wall plugs

Item no. Item Description Unit Rate Total Qty. Amount

Providing and fixing 6mm thick frameless mirror of approve make in any shape and sizes as per drawing. Mirror

shall be fixed on 12mm thick marine plywood backing. Marine plywood shall be fixed to wall with approved SS

108 fastener. All edges of glass shall be sharp grinded, cut corner and polished. Glass shall be fixed with approved SQM 5,897.00 119.00

adhesive/ 3M tape etc. complete at all floors/ all levels/ all heights as directed by Engineer In Charge. Installed

area of mirror shall be considered for payment without wastage.

Structural steel work ( Confirming to IS 4923-1997) riveted, bolted or welded in builtup for all type sections, in

framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all

complete as per the structural designs and directions of Engineer in charge.

Providing, fabricating, assembling, hoisting/ erecting and fixing for structural steel work in position at all heights/

all levels/ all floors/ all shapes & sizes with all leads & lifts using MS Rolled Steel Sections, Hollow sections,

Tubular Sections, MS Plates, Chequered Plates, MS Pipes, Perforated Sheet, Flats, Bright Bars, Angles, MS

Sheet, Girder, Beam, cattle trap. deep threaded MS bolts, threaded J bolts, insert plate, support plate etc as per

drawing. all confirming to latest relevant IS codes for the work of steel structures like gratings over drain channel,

I beams, staircases, railings, handrail, jali, gates, grills, bracings, platforms, brackets, monkey ladder, cattle trap,

windows, pipe rack, rungs, false ceiling frame work, Roof canopy, fencing posts, M.S. Screen & fencing jali frame

work etc. including straightening, cutting, bending, bolting and welding the members all as per structural drawings

and as per detailed specifications (for materials & workmanship) including necessary scaffolding/ staging etc.

complete in the situations described hereinafter and comprising of : i) Profile Cutting of components to required

length/ width and shape/ profile;

ii) Smooth grinding/ machining of edges/ faces/ all welding joints; iii) Necessary welding (electric arc welding) for

required weld lengths and sizes. (non structural elements) iv) Machine drilling of holes for joining/ anchoring

(Standard measurements will be paid for as actual cut length used at site).

Note: The contractor shall be submit fabrication drawings based on construction drawings (that may be issued

during construction period with at least one mock up approved by architecture ) for approval by the Architect/

Engineer. The fabrication work shall start only after approval of the fabrication drawings submited by contractor.

Any change required in the fabrication drawings shall be carried out at No extra cost. Fabrication shall be in a

perfect architectural workmanship manner and as provided in section V & VI of IS 800 & IS 7215. Welding shall

be carried out by qualified welders/ fabricators.It should also include the cost of necessary scaffolding/ staging,

zinc coated nut-bolt as required for safety, structural stability of all works at site.

Extra on STRUCTURAL STEEL item - for all kinds of sleeves in hydraulic structure Hot dip Galvanised with

110 minimum 65microne thick (only difference shall be paid instead of 2 coat zinc chromate yellow oxide and 2 coat of KG 92.00 505.00

Providing and fixing G.I. chain link fencing of required width in mesh size 50x50 mm including strengthening with

2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-charge.

111 Made of G.I. wire of dia 4 mm SQM 3,393.00 25.00

Item no. Item Description Unit Rate Total Qty. Amount

Providing and wet drilling accurate and clean holes of 25‑400 mm range without vibration through Hilti diamond

drilling machine DD200 having 1:1 & 1:3 gearing ratio for wide range of reinforcements in concrete, control panel

112 indicator to display proper pressure application, capable of drilling at angle from 0o‑ 45o and do overhead

application. Before coring rebar loaction to be identifed with Hilti PS 250 (ferroscanner) tool or equvivalent.

TOTAL OF MISCELLENEOUS

K FURNITURE WORK

Providing And Supply High Back Rev. Chair Upholstered with Leatherette Seat Made Up Of 12mm +/- 1mm Thick

Hot Pressed Mr. Grad Plywood and Back in Two Pieces - 12mm Rear Back And 6mm Inner Back. Moulden

Polyurethane Foam Used in Making Seat with Molded Density 45+/- 2 Kg/M ³. Back Is Made Out Of 32 Density

Block Foam Covered With 14mm Thick 32 Density Foam Sheet (Block Foam). Spine Bracket Made Of M.S Plate

8mm Thickness Connecting Back with Mechanism. Armrest Top Is Soft Touch Polyurethane Molded Of 250 To

300 Density Insert Stainless Steel Pipe Having Unique " Y "Shape. The Mechanism of the Chair Have Following

Features: 360⁰ Revolving Type 3.5Mm Thk Crca Seat Plate With 4Mm Thk Crca Channel Plate Synchro

Mechanism, Tilt Tension Adjustable, Single Position Locking, Plastic Component Inside the Mechanism of Grade -

Mi 3530 And Epoxy Powder Coated 70 Microns with Tested 1.2 Lacs Cycles as Per Bifma Standard. The Chair

113 Provided with Pneumatic Height Adjustment Which Have Have Stroke Of 100mm +/- 5mm.The Five Leg Base Is Nos 16,168.00 3.00

Made Up Of 38Mm Dia X 1.2Mm Thick Tubular With 3.15mm Thick Centre Hub Crc Fabricated Chrome Finish. It

Have Be Fitted With 50mm Dia Twin Wheel Castor . The Size of The Base Have Be - 660 +/- 1mm Pitch-Centre-

Diameter. Load Test As Per Bifma Compliance. The Twin Wheel Castors Made Of Nylon Injection Molded In

Black Color. Overall Dimensions Of Chair Have Be, Width Of Chair - 640mm, Depth Of Chair 640mm As

Measured From Base Below. Height Of Back From Ground - Min 1175 To Max 1275mm. Seat Height -Min

480mm To Max 580mm. Dimensions Tolerance / Variations Have Be Within +/- 10mm.

Item no. Item Description Unit Rate Total Qty. Amount

Providing And Supply Med. Back Rev. Chair Upholstered With Leatherette Seat Made Up Of 12mm +/- 1mm

Thick Hot Pressed Mr Grad Plywood And Back In Two Pieces - 12mm Rear Back And 6mm Inner Back. Moulded

Polyurethane Foam Used In Making Seat With Moulded Density 45+/- 2 Kg/M ³. Back Is Made Out Of 32 Density

Block Foam Covered With 14mm Thick 32 Density Foam Sheet (Block Foam).Spine Bracket Made Of M.S Plate

8mm Thickness Connecting Back With Mechanism. Armrest Top Is Soft Touch Polyurethane Moulded Of 250 To

300 Density Insert In Stainless Steel Pipe Having Unique " Y "Shape. The Mechanism Of The Chair Have

Following Features: 360⁰ Revolving Type 3.5Mm Thk Crca Seat Plate With 4Mm Thk Crca Channel Plate

Synchro Mechanism, Tilt Tension Adjustable, Single Position Locking , Plastic Component Inside The Mechanism

Of Grade - Mi 3530 And Epoxy Powder Coated 70 Microns With Tested 1.2 Lacs Cycles As Per Bifma Standard

114 The Chair Provided With Pneumatic Height Adjustment Which Have Have Stroke Of 100mm +/- 5mm.The Five Nos 19,716.00 26.00

Leg Base Is Made Up Of 38Mm Dia X 1.2Mm Thick Tubular With 3.15mm Thick Centre Hub Crc Fabricated

Chrome Finish. It Have Be Fitted With 50mm Dia Twin Wheel Castor . The Size Of The Base Have Be - 660 +/-

1mm Pitch-Centre-Diameter. Load Test As Per Bifma Compliance.The Twin Wheel Castors Have Be Made Of

Nylon Injection Moulded In Black Colour.Overall Dimensions Of Chair Have Be, Width Of Chair - 630mm, Depth

Of Chair 630mm As Measured From Base Below. Height Of Back From Ground - Min 950 To Max 1050mm.

Seat Height -Min 470mm To Max 570mm. Dimensions Tolerance / Variations Have Be Within +/- 10mm.

Providing and supply Seat and back in single piece with integrated arms like bucket shape, nylon moulded of

to 500 density fix inner and outer snap fit arrangement in back with mesh fabric inside on equal interval of

rectangular slots design. The mechanism of the chair have have following features : 360⁰ revolving type, 2.5mm

thk CRCA powder coated center tilt Mechanism, Tilt tension adjustment, locking in single position, Plastic

115 component inside the mechanism of Grade - MI 3530 and Epoxy Powder coated 70 Microns with tested 1.2 lacs Nos 11,184.00 20.00

cycles as per BIFMA Standard The chair have be provided with pneumatic height adjustment which have have

stroke of 100 +/- 5 mm. The Base have be made of injection moulded nylon. It have be fitted with 5 nos. twin

wheel castor - 50 mm diameter. The size of the base be 660 +/- 1 mm pitch-centre-diameter. The twin wheel

castors have be made of Nylon injection moulded in black colour.

Providing And Supply Med. Back Rev. Chair Upholstered With Leatherette Seat Made Up Of 12mm +/- 1mm

Thick Hot Pressed Mr Grad Plywood And Back In Two Pieces - 12mm Rear Back And 6mm Inner Back. Moulded

Polyurethane Foam Used In Making Seat With Moulded Density 45+/- 2 Kg/M ³. Back Is Made Out Of 32 Density

Block Foam Covered With 14mm Thick 32 Density Foam Sheet (Block Foam). Armrest Top Is Soft Touch

116 Polyurethane Moulded Of 250 To 300 Density Insert In Chrome Finish Pipe Having Unique "Bird Beak"Shape.. Nos 14,829.00 50.00

Pipe structure of MS CRCA finish 16 gauge round pipe having a diameter of 25 mm with epoxy powder coated.

Overall Dimensions Of Chair Have Be, Width Of Chair - 630mm, Depth Of Chair 630mm As Measured From

Base Below. Height Of Back From Ground - Min 950 To Max 1050mm. Seat Height -Min 470mm To Max 570mm.

Dimensions Tolerance / Variations Have Be Within +/- 10mm.

Item no. Item Description Unit Rate Total Qty. Amount

Type: 2 Seater Sofa

Size (approx. Over all dimension): 1500mm(W) x 800mm(D) x 780mm (H) Top: Upholstery with Latherite Finish

all visible surfaces

Specifications:Providing and supply Sofa sturcture made from 18mm MR Grade Mr grad plywood supported with

Maranti Solid wood, back side and curved part Covered with 3mm flexi ply, sofa arm made from 12mm thick MR

Grade Mr grad plywood supported with maranti solid wood. Elastic Belt, 75mm board & 2.25 mm thick elastic

webbing stapling in seat frame at 100 mm centre to centre distance, belt fastern in X and Y axies of seat, elastic

117 belt elongation 45% tensile strength 350 kg. Foam 100 mm X 40 density Premium Quality foam covered with Nos 70,414.00 6.00

25mm X 32 density super soft Premium Quality Foam for soft touch filling in seat. 50 mm X 40 density Premium

Quality foam covered with 25mm X 32 density super soft Premium Quality foam for soft touch filling in back.

Stiching Stiching work done with well known german brand (Aman / Gutermann) Thread. Nylone & Polyster thread

used as per application. Leg made from Stainless steel 316 Grade. all material selection will be as per architect's

selection, etc all complete with respect to necessary hardware and finishes

CENTER TABLE SIZE:-1100 x 600 & 450mm height

Providing fixing and arranging Center Table Providing and supply Top 20 mm thick made of PLY with 1 mm thick

laminate finish with 2 mm thick PVC edge bidding matching with same laminate finish.

118 STRUCTURAL SUPPORT SYSTEM:- shall be constructed using 40 x 40 mm matt finish S.S. Metal frame legs as Nos 22,367.00 3.00

per image. Entire table to be finished with all necessary hardware and selection of material as per architect.

SIDE TABLE SIZE:-500 x 500 & 450mm height

Providing fixing and arranging Center Table Providing and supply Top 20 mm thick made of PLY with 1 mm thick

laminate finish with 2 mm thick PVC edge bidding matching with same laminate finish.

119 STRUCTURAL SUPPORT SYSTEM:- shall be constructed using 40 x 40 mm matt finish S.S. Metal frame legs as Nos 11,598.00 3.00

per image. Entire table to be finished with all necessary hardware and selection of material as per architect.

"C" shaped table overall dimension 2250x1800x2700mm & 750mm height with 36 MM thick nail curvica post

forming edges made of 17mm OSR MDF with curvica laminate finish both long edges with ends having matching

2mm pvc edge band / beading, bottom surface to be finished with balancer white. Provision to be given for snake

/ vertebrae from floor to wire manager for pop up box with switches and sockets as per detail design and

drawings. Fixed Drawer Unit Outer body 17mm thick MDF with curvica Laminate Finish. three drawers with

bullnose front with lock and necessary hardware. Side Table : Size as per drawings, Top and leg 36 MM thick nail

curvica post forming edges made of 17mm OSR MDF with curvica laminate finish both long edges with ends

having matching 2mm pvc edge band / beading. shutter 17mm thick OSR MDF with curvica Laminate Finish

120 bullnose curvica laminate finish with lock and necessary hardware. Back Unit size as per drawing Top and leg 36 Nos 1,36,685.00 3.00

MM thick nail curvica post forming edges made of 17mm OSR MDF with curvica laminate finish both long edges

with ends having matching 2mm pvc edge band / beading. shutter 17mm thick OSR MDF with curvica Laminate

Finish bullnose curvica laminate finish with lock and necessary hardware. Entire table to be finished with all

necessary hardware. There will be provision of footrest of size 750 x 400 x 150mm & storage top side and back

unit top having a ledge of 150mm x 100mm boxing as shown in image included in it. All hardware should be

concealed & not visible. All handles should be concealed with SS finish.

Item no. Item Description Unit Rate Total Qty. Amount

Product : Collaborate Loop Leg Design

Dimensions : 1200mmL x 600mmD x 750mmHT Table top + 350mmHT Screen

Table Top: 25mm thick Pre laminate particle board with 2mm PVC edge lipping on all exposed edges

Support: End Legs: MS powder coated Collaborate Loop legs

Intermediate Legs: MS podwer coated 60X40mm legs and supporting MS cross beams (40X20mm)

Main Screen : 900mmL x 350mmHT - 18mm Thick Al. Framed Fabric Magnetic Screen with in-built Accessories

Rail mounted on table top with Powder coated Studs

Return Screen : 8mm Sandwich Glass Screen of 350mmHt x 525mmL mounted on table top with metal powder

121 coated studs Nos 10,638.00 12.00

Modesty : 12/18mm thick PLT modesty leg to leg for privacy of 450mmHt with 225mm Floor Clearance Gap

Wire Management

250mm Ht Racway with 65mm Dia Wire Manager Grommet

Vertical Raceway with built in separator for power and data of size 250H X 70mm thick with provision to mount

swicthes and sockets on laminate facia with Vertical Wire Entry cover for wire uptake from floor to raceway with

65mm Dia Wire Manager Grommet.

TABLE SIZE Linear shaped :-1200 x 600 & 750mm height

Providing and supply Top 36 mm thick made of PLY with 1 mm thick laminate finish with 2 mm thick PVC edge

bidding matching with same laminate finish. Apron 18mm thick PLY board with 1mm thick laminate finish with

122 mm thick PVC edge matching with laminate bidding, under structure made of 50x50mmx1.6mm thick MS square Nos 24,852.00 7.00

pipe with powder coated (50-60 micron) finish. WIRE MANAGEMENT MS-Powder coated wire tray with pop up

box switch plate and vertical cable raisers / PVC wire guard are considered for wire management.

TABLE SIZE Linear shaped :-1350 x 600 & 750mm height

Providing and supply Top 36 mm thick made of PLY with 1 mm thick laminate finish with 2 mm thick PVC edge

bidding matching with same laminate finish. Apron 18mm thick PLY board with 1mm thick laminate finish with

123 mm thick PVC edge matching with laminate bidding, under structure made of 50x50mmx1.6mm thick MS square Nos 24,852.00 1.00

pipe with powder coated (50-60 micron) finish. WIRE MANAGEMENT MS-Powder coated wire tray with pop up

box switch plate and vertical cable raisers / PVC wire guard are considered for wire management.

Item no. Item Description Unit Rate Total Qty. Amount

Providing and Fixing coustmised conferece table of 3000x1200x750 STRUCTURE:- Set of table top, modesty and

gable end designed in handshake pattern to build the closed module, open module of Video conferencing pattern

V-shaped configuration of the conference table with infinite seating arrangement depending upon space available

to set the conference table. TABLE TOP:- 30mm thick table top made up of 18mm thick ply wood with 1 mm thick

laminate board with 12mm thick thin PVC foil wrapped decorative profile made up of ply fixed along all the edges

from the bottom side which provide decorative waterfall edge profile to top with twin colour look the decorative

trim to be connected at the angle of 45 degrees with each other. Single seater small top of size 675mm width and

600mm depth. Two-seater big top of size 1350mm width and 600mm depth can shape open type and O shape

close type configuration. Two-seater end top of perfect semicircle shape of the radius of 600mm usable for the

close module with the lowest space of 1200mm in front to front seating. LEG:- 25mm thick Leg or Gable End

made up of 25mm thick pre-laminated particle board with MS leveller bracket to give floating look. MODESTY:- 2.00

Modesty Panel made up of 18mm thick ply wood with 1 mm thick laminate providing stability to structure and allow

sufficient leg privacy to the user. "D" headed decorative aluminium profile fixed on it. WIRE MANAGEMENT:-

Provision for wire passing throughout the structure without mixing data and power connections. The wires can be

124 pulled inside the table from floor and placed in the boxes build below openable shutter. The access point for data Nos.

and power can be mount on the main top as well as the openable top. Access flap is box structure made up of

aluminium extrusion with necessay switches and sockets and connectivity to different equipments. etc all

complete with necessary hardware and complete as directed by engineer incharge. all visible and non visible

surfaces to be claded with 1 mm thick laminate as per detail design drawings.

WIRE MANAGEMENT:- Provision for wire passing throughout the structure without mixing data and power

connections. The wires can be pulled inside the table from floor and placed in the boxes build below openable

shutter. The access point for data and power can be mount on the main top as well as the openable top. Access

flap is box structure made up of aluminium extrusion with necessay switches and sockets and connectivity to

different equipments. etc all complete with necessary hardware and complete as directed by engineer incharge.

all visible and non visible surfaces to be claded with 1 mm thick laminate as per detail design drawings.

Providing and fixing lockable cupboard of size 1200x450x2100 mm with 4 shelves two parts. Material – 0.7mm

thick (+/-0.07mm) CRCA for shelf; 0.8mm thick (+/-0.08mm) high yield strength CRCA for doors & back; 0.9mm

thick (+/-0.08mm) CRCA for all other components. It should have 2 way locking mechanism with shooting bolt &

125 rase s per req.handle or without handle.. It should have height wise adjustable shelf With uniformly distributed Nos. 32,308.00 1.00

load capacity per each full shelf 40kg maximum. Finish – Epoxy Powder Coated to the thickness of 50 microns (+/-

10).etc complete with all necessary hardware. all handles to be consealed. no hinges to be visibal. shade of

powercoating will be as per architect's choice.

Providing and fixing File Storage.1500x450x750mm Top made of 25 mm thick PLY bothside covered 1 mm thick

laminate finish ,sides 18 mm thick PLY bothside covered 1 mm thick laminate finish.9mm thk PLY bothside coberd

with laminate finish.Skirting and Front Shutters/drawer fascia made of 18 mm thick ply bothside covered 1 mm

126 thick laminate finish with necessary hinges and lock. Shutter hanging on Hinges, Lock and handle are consealted Nos. 39,349.00 3.00

or profile or groove handle less etc.All edge 2mm thick Pvc beading matching with laminate will be provided.etc all

necessary hardware included and complete as per image and detail design and drawings. all laminate shaed are

to be as per architects's selection.

Item no. Item Description Unit Rate Total Qty. Amount

Supply, fabrication, and installation of modular kitchen cabinets using economical materials, with carcass made of

commercial plywood or pre-laminated particle board finished with 0.8 mm laminate or pre-laminated surfaces on

both sides and basic edge banding to exposed edges, shutters made of commercial plywood or MDF finished with

0.8 mm laminate on the outer face and white or balancing laminate on the inner face, and provision of drawers

127 using basic telescopic channels (non-soft close) along with stainless steel (SS) wire trolleys in place of tandem RMT 20,710.00 516.00

systems, including basic cutlery tray and essential storage accessories; all visible surfaces to be finished in

matching laminate shades selected and approved by the Architect/Engineer-in-Charge, and the work to include

complete installation of the kitchen unit with all necessary basic hardware such as hinges, handles, channels,

fittings, and accessories as per drawings and site requirements

Providing and fixing in position PVC Frosting Glass film of approved make (of any pattern, shade and type) on

glass partitions and doors for internal use. Film shall be pasted on glass without any appearing any air bubble.

128 The rates shall be for all shapes and all heights with necessary scaffolding complete as per the Architectural SQM 1,243.00 20.00

drawings and manufacturer's specification & instructions as directed by the Architect and Engineer-in-charge. Film

shall be with 10 years warranty.

Providing and fixing roller blinds with composition 100% Polyester . Fabric woven and semi opaque / coated

translucent fabric & Complete Blackout. The fabric shall be enclosed in the suitably created pocket along with

tube i.e Palmate. Fabric Warranty 3Year. Weight 190 GSM, Width 280 cm, Thickness 0.48mm, Light fastness is

to 5 grade. Mechanism made in UK with ball chain mechanism & with 5 years mechanism warranty. The Roller

tube extruded by non-rusting Aluminium alloy with 1.25 mm thickness. Available in 32, 38, &45 mm diameters for

small and big blinds respectively. Mechanism is designed with support beam to keep it straight and have a pocket

for holding the fabrics in position. The mounting brackets shall be universal and capable of mounting inside/

outside/ ceiling / wall with the clutch on either the right or left end of the tube. Mechanism to be operated with

control unit made of high strength ABS plastic. Mechanism shall be operating with the use of a ball chain, made

up of unbreakable polyethylene plastic, 1.50mm polyester cord with 4.50 mm balls. The blind shall be able to stop

at any desired position with the help of stop lock. The bottom channel of Roller Blind shall be matching shade with

fabric and made of non-rusting aluminium powder coated with 1.50 mm thickness. The fabric shall be enclosed in

the suitably created pocket along with tube.

TOTAL OF FURNITURE

Parking Suspended Sign : Providing a signs made as using Modular Aluminium extrusions (Alloy 6060 as per

European standards EN755-2-2008 tensile strength 190 MPa made from virgin homogeneous aluminium billet)

with Premium grade Anodizing (Thickness 15-20 microns) as per International standards, with 10 years warranty

under normal working conditions.Sign is double sided 50 mm depth profile with media accomodation depth of

130 mm media of ACP acrylic upto 5 mm thickness can be pasted directly on frames or attched on frame with help of Nos. 33,350.00 9.00

dual lock tape.Sign can be edge lite with help of edge lite led modules ,led of LUCOLED make EL31 , fitted and

installed at site in plumb and level at specified location as per drawing to the satisfaction of the engineer-in-

Item no. Item Description Unit Rate Total Qty. Amount

Door Nameplate Sign - Providing a signs made as using Modular Aluminium extrusions (Alloy 6060 as per

European standards EN755-2-2008 tensile strength 190 MPa made from virgin homogeneous aluminium billet)

with Premium grade Anodizing (Thickness 15-20 microns) as per International standards, with 10 years warranty

under normal working conditions.Sign is single sided with 1 aluminium profile click fitted on 2 plastic moulded

131 endcaps.Sign is including all plastic injection moulded end caps black in shade which are directly press fitted Nos. 1,988.00 101.00

,media can be flat bed UV printed on panels/ profiles.Cosign make MPI panels fitted and installed at site in plumb

and level at specified location as per drawing to the satisfaction of the engineer-in-charge.

Floor directory sign - Providing a signs made as using Modular Aluminium extrusions (Alloy 6060 as per

European standards EN755-2-2008 tensile strength 190 MPa made from virgin aluminium homogeneous billet)

with Premium grade Anodizing (Thickness 15-20 microns) as per International standards, with 10 years warranty

under normal working conditions.Sign is single sided with aluminium side tracks and common click clips for panel

132 fitting. a.Sign is including all plastic injection moulded clips black in shade which are slided in side tracks ,media SQM 2,070.00 5.00

can be flat bed UV printed on panels/ profiles.Cosign make MPI panels fitted and installed at site in plumb and

level at specified location as per drawing to the satisfaction of the engineer-in-charge.

Toilet Door Sign - Providing a signs made as using Modular Aluminium extrusions (Alloy 6060 as per European

standards EN755-2-2008 tensile strength 190 MPa made from virgin homogeneous aluminium billet) with

Premium grade Anodizing (Thickness 15-20 microns) as per International standards, with 10 years warranty

under normal working conditions.Sign is single sided with 1 aluminium profile click fitted on 2 plastic moulded

133 endcaps.Sign is including all plastic injection moulded end caps black in shade which are directly press fitted Nos. 746.00 8.00

,media can be flat bed UV printed on panels/ profiles.Cosign make MPI panels fitted and installed at site in plumb

and level at specified location as per drawing to the satisfaction of the engineer-in-charge.

Closet Door sign - Providing a signs made as using Modular Aluminium extrusions (Alloy 6060 as per European

standards EN755-2-2008 tensile strength 190 MPa made from virgin homogeneous aluminium billet) with

Premium grade Anodizing (Thickness 15-20 microns) as per International standards, with 10 years warranty

under normal working conditions.Sign is single sided with 1 aluminium profile click fitted on 2 plastic moulded

134 endcaps.Sign is including all plastic injection moulded end caps black in shade which are directly press fitted Nos. 746.00 44.00

,media can be flat bed UV printed on panels/ profiles.Cosign make MPI panels fitted and installed at site in plumb

and level at specified location as per drawing to the satisfaction of the engineer-in-charge.

Lift Number sign - Providing sign of Cosign make Modular Aluminium extrusions (Alloy 6060 as per European

standards EN755-2-2008 tensile strength 190 MPa Made from virgin homogeneous aluminium billet) with

premium grade anodizing (Thickness 15-20 microns) as peinternational standards, with 10 years warranty under

135 normal working conditions. Profile to form frame with overall depth of 10 mm with media of thickness upto 3mm. 2 Nos. 1,380.00 30.00

mm thick acrylic/ACP . I-sign Fix profile of Cosign make with M.S zinc coated corners with grub screws. Installed

at site in plumb and level at specified location as per drawing to the satisfaction of the engineer-in-charge.

Item no. Item Description Unit Rate Total Qty. Amount

Emergency Exit sign - Providing ready sign & fixing at location a Cosign make emergency exit sign- illuminated,

surface mount (wall or ceiling) Dual sided made up of plastic material , battery backup of 3 hours (180 mins)

.Battery life of 300 cycles of charge & discharge Li- ion battery 3.7 Volt, 100 mA, Charge time of 24 hours. Input

voltage 220-240 Volt A.C, 50/60 Hz. Viewing distance 30 meter, degree of protection IP20 (rating for protection

against solid object upto 12 mm) white light colour full back (white colour) LED illumination with green white

coloured graphic inserted on both sides on 0.4 mm PC (sizes, texts, symbols or graphics as per standard safety

norms & regulations) graphic options of -left ,right, up staircase down staircase. Test facilty button self test plus

auto self test, opreration in maintained and non maintained mode (power saver mode).Sign with 12 months

warranty for electric circuit & 6 months warranty for battery. Sign provided with dual mounting arrangement of

mounting on wall & celing both ( with flat rigid support/base).Sign is including all connection wires (upto 1 mtr) &

high tensile strength zinc coated self tapering screws (4 nos with screw wall plastic packing), installed at site in

plumb and level at specified location as per drawing to the satisfaction of the engineer-in-charge.

BUILDING SIGNAGE - Aluminium Channel Letters -

Specifications:

Supply and installation of 1mm thick and 4" depth Aluminium Channel letters with proper backside fabrication with

3mm acp female and 3mm acrylic having led of GOQ 3 Genius 2835 having 5 years warranty and power supply

of Union/E-power with 5 years warranty. Wiring to be done by using 1.5mm wire of Finolex brand.

137 5 Years warranty Power dissipation ‑ Nos. 11,500.00 21.00

View angle ‑ 175 Luminous flux ‑ 90lm

Colour cct ‑ Pure White, 10000k Cool

white Dimensions (mm) 66*15*10.5._

TOTAL OF SIGNAGES

Design, supply, delivery and installation of FRP Surface Heavy Duty Recessed Manhole Cover with Frame

(450mm x 450mm clear opening) for sewer manholes and storm water catchpits, including proper seating in

138 RCC top slab, alignment, grouting, finishing and all complete as per drawings and specifications, including all Nos. 8,867.00 10.00

materials, labour, tools, transportation, and fixing at site.

Design, supply, delivery and installation of FRP Surface Heavy Duty Recessed Manhole Cover with Frame

(600mm x 600mm clear opening) for sewer manholes and storm water catchpits, including proper seating in

139 RCC top slab, alignment, grouting, finishing and all complete as per drawings and specifications, including all Nos. 17,118.00 22.00

materials, labour, tools, transportation, and fixing at site.

Design, supply, delivery and installation of FRP Water Gully cover with Frame Heavy Duty (600mm x 600mm

clear opening) for valve chambers, including proper seating in RCC top slab, alignment, grouting, finishing and

140 all complete as per drawings and specifications, including all materials, labour, tools, transportation, and fixing at Nos. 13,082.00 2.00

Providing, supplying and fixing FRP moulded grating of 38mm thickness, panel size 310mm x 1220mm,

141 including cutting to required sizes, proper placement over supporting frame, fixing with suitable clamps/fasteners, Nos. 1,271.00 41.00

alignment, and all necessary accessories, complete as per drawings and specifications.

TOTAL OF MEPF WORK

AHMEDABAD MUNICIPAL CORPORATION

Construction of Fire Station and Staff Quarters at T.P 76 F.P. 115-1 in Ramol Ward,

East Zone, Ahmedabad city under Building Project Department.

SUBESTIMATE - 03 : HVAC WORK

S. NO. ITEM DESCRIPTION AMOUNT

A SUB TOTAL - DX SYSTEM

B SUB TOTAL - AIR DISTRIBUTION NETWORK

C SUB TOTAL - CIVIL SUPPORT STRUCTURE

D SUB TOTAL -DUCT INSULATION

E SUB TOTAL - VENTILATION FANS

Total of HVAC Works

F MAINTENANCE & OPERATION FOR HVAC

TOTAL OF MAINTENANCE & OPERATION FOR HVAC

AHMEDABAD MUNICIPAL CORPORATION

Construction of Fire Station and Staff Quarters at T.P 76 F.P. 115-1 in Ramol Ward, East Zone, Ahmedabad city under Building Project Department.

BOQ FOR SUBESTIMATE - 03 : HVAC WORK

Item Description

Item no. Unit Rate Total Qty. Amount

MECHANICAL WORKS

Providing and erecting Inverter based approved make split air-conditioning unit consisting of

condensing unit with variable speed fan motor, inverter type hermetically sealed rotary compressor with

accessories etc. duly connected separately erected evaporating unit and blower motor with its

1.0 accessories by means of extra supplied proper insulated copper tubing,drain PVC pipes suitable for (

cost includes Eco Friendly green gas charging and 15A plug top & Remote Control & MS Stand) with

necessary core cutting.

(2)For ISEER Range (KWH/KWH)(4.0 to 4.49)

a) for 0.8 to 1.0 ton capacity- Premium cat.

b) 1.5 ton capacity- Premium cat.

Providing and erecting Inverter based approved make Cassette type split air-conditioning unit

consisting of condensing unit with fan motor, hermetically sealed scroll/rotary compressor with

2.0 accessories etc. duly connected separately erected evaporating unit and blower motor with its

accessories by Eco friendly Green gas charging & Internal copper wiring & Remote control ( 3 star and

above of current year) with necessary core cutting.

(A) for 1.5 ton capacity

(B) for 2 ton capacity

(C) for 3 ton capacity

(D) for 4 ton capacity

Supplying & installing MS standard type stand mounting for outdoor unit of Split A.C. upto 4 TR

capacity erected with necessary hardware materials as directed.

Supplying and erecting insulated pair of soft copper tubing open or concealed including power and

control cable,necessary PVC drain pipes for Split AC machine up to 4 TR capacity

Supplying and installing MS angle , powder coated / Painted standard type of wall/floor stand mount for

outdoor unit of split AC of following capacity, erected with necessary hardware materials as directed.

5.0 (A) 25mm*25mm*3mm thick M.S angle suitable for upto 2 TR. Capacity of ac machine Each 1,305.00 -

Item Description

Item no. Unit Rate Total Qty. Amount

6.0 DRAIN PIPING :

Rigid UPVC drain pipe of 10 Kg/cm2. rating with 9 mm thick.nitrile rubber insulation.

A SUB TOTAL - DX SYSTEM

B AIR DISTRIBUTION NETWORK

Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal

rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers,

6.0 vanes, hangers, supports etc. as per approved drawings and specifications of following sheet

complete as required.

Supply, installation, balancing and commissioning of fabricated at site GSS sheet metal

rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes,

7.0 hangers, supports etc. as per approved drawings and specifications of following sheet thickness

complete as required.

Item Description

Item no. Unit Rate Total Qty. Amount

Supply and installation of MS Welded rectangular ducts, complete with required flanges , necessary

supports of pregalvanised steel of 275gsm and 4.8 strength class threaded rods (as directed) and ETA

8.0 Approved anchor bolts, supply air collars, vanes, splitters dampers and as per specification for Air

Conditioned Areas - For Kitchen Exhaust

( Support Shall be provided as free supply to the contractors )

8.1 18 G MS Ducting Sqm. 2,450.00 2.00

Supply, installation, testing & commissioning of thermal insulated flexible duct

of following sizes duly supported at regular interval as per site requirement etc.

9.0 complete as required as per Mtr 696.00 10.00

specifications.(A) 200 mm dia.

SUPPLY INSTALLATION TESTING AND COMMSSIONING OF DIFFUSERS/ GRILLES AS PER

FOLLOWING SCHEDULE

Supplying & fixing of powder coated extruded aluminium Supply Air Grills with aluminium volume

10.1 control dampers complete as per specifications and size & shape as per site requirement and approved SQM. 10,328.00 0.50

Supplying & fixing of powder coated extruded aluminium Return Air Grills with louvers but without

10.2 volume control dampers complete as per specifications and size & shape as per site requirement and SQM. 7,003.00 1.00

approved design.

Supplying, fixing testing commissioning of supply air diffuser of powder coated aluminium with

10.3 aluminium volume control dampers with anti smudge ring & removable core and size & shape as per SQM. 13,553.00 0.50

site requirement and approved design.

Supplying, fixing testing commissioning of Return air diffuser of powder coated aluminium without

10.4 volume control dampers with anti smudge ring & removable core and size & shape as per site SQM. 9,301.00 0.50

requirement and approved design..

Supply fixing and testing , commisioning of Aluminium Powder Coated Slot Diffuser complete with

plenum box and volume control damper. Color , size & shape as per site requirement and approved

11.0 design.. Neccessory ancilery item for fixing cost should be included.

Contractor need to revalidate the diffuser selection before preparing shop drawing.

12.0 Rain Protection Fresh Air Grill for Façade installation. Sqm 7,500.00 20.00

13.0 SUPPLY, INSTALLATION, TESTING, COMMISSIONING OF DUCT DAMPERS

Supply, installation, testing and commissioning of GI volume control duct damper complete with

neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc, as per specifications.

Item Description

Item no. Unit Rate Total Qty. Amount

Supplying, Fixing, testing and commissioning of fire dampers in supply air duct/main branch and

return air path as and where required of required sizes i/c control wiring,the damper shall be motorized

and spring return so as to close the damper in the event of power failure automatically and open the

13.2 same in case of power being restored. The spring return action shall be inbuilt mechanism and SQM 11,905.00 0.50

not externally mounted. The damper shall also be closed in the event of fire signal complete

as required and as per specifications.

(A) Fire damper

13.3 (B) Actuator Each. 11,153.00 0.50

14.0 Double Layer Weather Proof Machine Canvass Connection ( FAN ) Set 3,500.00 2.00

B SUB TOTAL - AIR DISTRIBUTION NETWORK

C CIVIL SUPPORT STRUCTURE

15.0 Vibration Absorbant spring supports for Fans ( 4 to 8 Support for each FAN ) Set 1,500.00 2.00

16.0 Engineered Rubber Support Pad for Split AC Out Foor Unit Set 1,800.00 7.00

MS Welded Structure (Supply and erection of M.S. angle stand with synthetic epoxy paint for all

18.0 Core Cut up to 150mm Dia Lot 1,350.00 4.00

C SUB TOTAL - CIVIL SUPPORT STRUCTURE

D DUCT INSULATION

19.0 DUCT THERMAL INSULATION

Supplying, laying, fixing, testing and commissioning of following thickness closed cell elastomeric

nitrile rubber of class 'O' applied by suitable adhesive, as per specifications and as required

complete in all respect.

19.2 13 mm thick SQM 610.00 - -

20.0 DUCT ACCOUTIC INSULATION

Providing and fixing acoustic Insulation of open cell nitrile rubber sheet having density of 180-220

kg/m3 and recommanded thickness of 15 mm. Absorption coefficient value of Insulation material shall

be 0.90 for the 2000 Hz frequency band in accordance to IS:8225/ISO:354/ASTM 423C. Material shall

have fire class 1 as per BS 476 , part 7. Material Shall be EPA approved and Anti-Fungal & Anti-

Bacterial in accordance with ASTM G21 & ASTM E 2180 respectively. It shall be fixed inside of the duct

with the help of adhesive as per the specifications given.FSK tape shall be applied at joints.

21.0 UNDER DECK INSULATION :

Item Description

Item no. Unit Rate Total Qty. Amount

Supply & Fixing Under deck Insulation with 50 mm thick Fire Retardant Extruded Polystyrene having

density of 32 Kg / M3 and thermal resistance of 1.78 M2 K / W

D SUB TOTAL -DUCT INSULATION

E VENTILATION FAN

22.0 CABINET TYPE INLINE CENTRIFUGAL EXHAUST AIR FAN

Supply, Installation, testing & Commissioning of Cabinet type Centrifugal Fans / Inline Fan for Exhaust

Air System complete with SISW Forward Curved blower, fan assembly shall be AMCA certified (AMCA

certification requird for Air Performance & Sound) & totally enclosed, fan-cooled, provided with class F

insulation, and of approved make.,

Fan shall be provided with TEFC Sq.cage, direct driven F' Class induction motor with minimum IP-55

Motor shall be suitable for 220 ± 5% volts, Single phase, 50 cycles electric supply- I OR 415+/-10% V,

50 hz, 3 phase AC. The motor (Eff1 Class-Motor must be VFD Compatible )

Max. noise level shall be 56 dBA at 1.5 meter in hemispherical reverberant room condition.

The complete fan assembly shall be CE Certified in accordance with EN-12101-3:2015 (Vendor shall

submit the certifications for below listed fans)

The Fan units shall be designed as per the criteria mentioned in the specifications and selected so as

to operate in the best efficiency zone; the units shall be statically and dynamically balanced.

Necessary starter shall be in scope of HVAC Contract. Power cable will be available up to starter panel.

The controller will be BMS compatible with all required open protocol and requried licence softares.

23.0 FAN FILTER UNIT

Item Description

Item no. Unit Rate Total Qty. Amount

SITC of Cabinet (Square) Type Inline Centrifugal Fresh Air Fan AMCA Certified (For Air and Sound

Performance) suitable for installing in any position in vertical or horizontal ducts. The casing shall be

single skin, internally acoustically lined and constructed of galvanised steel. The inline fan shall be with

Farword curve up to 1500 CFM & above shall be backward curve centrifugal impeller fitted with

maintenance free external rotor motor, flexible connections at the discharge & inlet. The motor shall be

suitable for 220 / 415±10% volt single/three phase 50 Hz AC supply. 3 phase fans quoted price shall

be inclusive of DOL starter panel with cabling between starter panel and fan. The fan shall have low

sound level exceeding not more than 65 DBA at 3 meter distance.

The fan shall have easily washable 20 micron fresh air filter. The Fan units shall be designed as per the

criteria mentioned in the specifications and selected so as to operate in the best efficiency zone; the

units shall be statically and dynamically balanced. Necessary starter / Panel / Power Cable shall be in

the scope of HVAC Contractor. Power cable will be provided up to starter panel.

24.0 WALL MOUNTED PROPELLER EXHAUST FAN WITH GRAVITY LOUVERS

Supply, Installation, testing & Commissioning of Propeller fan for wall or panel mounting suitable for

supply or exhaust use having casing, protection guard and impeller. Impeller shall be made with

galvanized steel. Entire assembly shall be black enamel painted to avoid the rust. The fan should have

sickle blade impellers with external rotor motor, fan assembly shall be AMCA certified (AMCA

certification requird for Air Performance & Sound) & totally enclosed, fan-cooled, provided with class F

insulation, and of approved make.,

Fan shall be provided with TEFC Sq.cage, direct driven B' Class induction motor with minimum IP-54

Motor shall be suitable for 230 ± 5% volts, Single phase, 50 cycles electric supply- I. The motor (Eff1

Class-Motor must be VFD Compatible )

Max. noise level shall be 60 dBA at 3 meter in hemispherical reverberant room condition.

The complete fan assembly shall be CE Certified in accordance with EN-12101-3 (Vendor shall submit

the certifications for below listed fans)

The Fan units shall be designed as per the criteria mentioned in the specifications and selected so as

to operate in the best efficiency zone; the units shall be statically and dynamically balanced.

Necessary starter shall be in scope of HVAC Contract. Power cable will be available up to starter panel.

Item Description

Item no. Unit Rate Total Qty. Amount

Cassettte type exhaust fan

26.0 Lift pressurization System

Supplying, installation, testing and commissioning of AMCA Certified (For Air and Sound Performance)

ceiling hung / floor mounted AXIAL flow fans of following capacity with GSS casing/ standard M.S.

construction and aluminium alloy impellers with high efficiency aero-foil sections, blades. The impeller

shall be directly driven by TEFC induction motor with high efficiency class IE2 . Motors shall be suitable

for 3 Phase, 50 Hz, 415V ± 10 %. Motors to be of class 'H' insulation for Supply/Fresh Air Fans and

class 'H' insulation/ 300° C for 2 hrs for smoke or normal Exhaust Fans. The Exhaust air fans-motor

assembly should be CE Listed as per EN-12101-3: 2015.. Motor make shall be same as mentioned on

the fire certificate. Fan total efficiency should not be less than 70%. Entire fan model & AMCA Seal

shall appear in technical submittal of fan. The Axial fans shall have sound level not more than 75 dB(A)

at three meter distance at both ends when measured in closed room conditions. Static pressure

calculation of Fans shall be checked by Vendor/Contractor prior to supply of Fans as per site condition.

If there is any discrepancy against the BOQ, the Vendor/Contractor has to take approval from Client &

Consultant, and nothing extra shall be paid.

Necessary starter shall be in scope of HVAC Contract. Power cable will be available up to starter panel.

The starter should be capable to run automatically in case of fire.

26.1 9000 CFM 18 mm WC ESP ( Liftwell Pres. System ) Set 85,000.00 4.00

E SUB TOTAL - VENTILATION FANS

TOTAL HVAC WORKS

AHMEDABAD MUNICIPAL CORPORATION

Construction of Fire Station and Staff Quarters at T.P 76 F.P. 115-1 in Ramol Ward, East Zone, Ahmedabad city under Building Project Department.

BOQ FOR SUBESTIMATE - 03 : HVAC WORK

HVAC WORK - AMC CHARGES

Item no. Item Description Unit Rate Total Qty. Amount

ANNUAL MAINTENANCE CONTRACT

(Note : From Each RA Bill, 5% retaination money to be deduct during O&M Period)

Annual Operation Contract of HVAC System for DLP + Four Years

Annual Operation Contract charges for Five years for entire HVAC system installed at the site including shiftwise

1.0 operation with one skilled operator throughout the working hours per shift for two shift. In all respect with periodical

regualr filter cleaning of all Indoor and Outdoor units

1.1 Annual Operation Charges only During Guarentee/Defect Liability period. Months 4,20,000.00 12.00

1.2 Annual Operation Charges only After Guarentee/Defect Liability period for First Year. Months 4,50,000.00 12.00

1.3 Annual Operation Charges only After Guarentee/Defect Liability period for Second Year. Months 4,80,000.00 12.00

1.4 Annual Operation Charges only After Guarentee/Defect Liability period for Third Year. Months 5,15,000.00 12.00

1.5 Annual Operation Charges only After Guarentee/Defect Liability period for Fourth Year. Months 5,52,552.08 12.00

Sub Total - OPERATION AND ROUTINE MAINTANACE

Comprehensive AMC for SITC of High Side units and Ventilation System

It includes all preventive maintanance , break down maintanance with all spares - repair or replacement of the

defactive part or parts , this includes all cosumable if any applicable.

2.1 1st year ( From the date of Completion of DLP ) Months 84,824.38 12.00

2.2 2nd year ( From the date of Completion of DLP ) Months 84,824.38 12.00

2.3 3rd year ( From the date of Completion of DLP ) Months 84,824.38 12.00

2.4 4th year ( From the date of Completion of DLP ) Months 84,824.38 12.00

Sub Total - Comprehensive Maintenance

AHMEDABAD MUNICIPAL CORPORATION

Construction of Fire Station and Staff Quarters at T.P 76 F.P. 115-1 in Ramol Ward, East Zone,

Ahmedabad city under Building Project Department.

SUBESTIMATE - 04 : ELECTRICAL & ELV WORK

ITEM DESCRIPTION AMOUNT

A Electrical Works

2a SERVO STABILIZER

3 JUNCTION BOXES

4 DISTRIBUTION BOARD

5 LT CABLES & CABLE TERMINATION

7 INTERNAL WIRING

8 INDOOR LIGHT FIXURE

11 SAFETY ITEMS

12 EXTERNAL LIGHT FIXTURE AND POLE

13 DWC PIPE AND CHAMBER

15 SERVICE WORK

16 RACEWAY/TRUNKING & JUNCTION BOX

Total of Electrical Works

17 FIRE DETECTION & ALARM SYSTEM

18 PUBLIC ADDRESS SYSTEM

19 VOICE COMMUNICATION SYSTEM

Total of ELV Works

AHMEDABAD MUNICIPAL CORPORATION

Construction of Fire Station and Staff Quarters at T.P 76 F.P. 115-1 in Ramol Ward, East Zone,

Ahmedabad city under Building Project Department.

SUBESTIMATE - 04 : ELECTRICAL & ELV WORK

ITEM DESCRIPTION AMOUNT

C Maintenance & Operation for Electrical & ELV Works

20 MAINTENANCE & OPERATION FOR ELECTRICAL & ELV WORK

E Comprehensive Maintenance for Lift Works

22 COMPREHENSIVE MAINTENANCE FOR LIFT WORK

F CCTV & Networking System Works

24 NETWORKING SYSTEM

Total of CCTV & Networking System Works

Tender Assumption List.

Quntity in this estimate are based on conceptual layouts and information received from various stackholders. It may

very as per detial design stage.

For Fire station and residential block LT services considered , Substation , meters space marked on drawing basis

of preliminary load. Liason person has to approve same from supply comapany.

All cabling & related assesories upto LT meters are in the scope of supply company, Clients scope start from LT

meters onwards.

4 Any specific equipent or requirement for Fire control center excluded from estimate.

AHMEDABAD MUNICIPAL CORPORATION

Construction of Fire Station and Staff Quarters at T.P 76 F.P. 115-1 in Ramol Ward, East Zone, Ahmedabad city under Building Project Department.

BOQ FOR SUBESTIMATE - 04 : ELECTRICAL & ELV WORK

Item no. Description Unit Rate Total Qty. Amount

1.1 Supplying and erecting, commissioning and testing of Diesel Generating set confirming to IS: Each 19,50,296.00 1.00

4722:1968 & BS:5514 having continuous rating, 3 phase, 415 volts, 50 cycles A.C. supply

comprising of a totally enclosed air/water cooled diesel engine with multi-cylinders developing

suitable BHP not less than following capacity at 1500 RPM with 10% overload for one hour in

hours with standard accessories like fly wheel, lubricating oil cooler, "A" class governor, heavy duty

fuel wheel and lubricating oil filter, oil bath air filler, lubricating oil pressure gauge, end exhaust

manifold, standard set of tools with adjustable spanners, screw drivers, cylinder head to cover, joint

cylinder head to exhaust, element lube oil filter, 12 / 24 volts electric starting equipment complete

with standard heavy duty battery, dynamo, cut-outs, ammeter, necessary wiring, pressure gauge,

starter etc and heavy duty Residential type exhaust silencer and vertical hot air duct both

logged with asbestos rope, save oil trays, exhaust piping of required length, standard wall/floor

mounted fuel with level indicator and piping and drip proof alternator, self excited, self regulated,

screen protected, with excitation system, capable of delivering the rated system output at 415 volts,

3 phase, 0.8 PF, 50 Hz, 4 wire, running at 1500 RPM, conforming to IS-4722- 1968 with voltage

regulation +/- 5% of rated voltage from no load to full load. Both the engine and alternator fitted

on a common fabricated steel base plate with antivibration mounting engine and alternator both

connected to each other by flexible flange coupling and with floor/wall mounted control panel box

comprising of voltmeter ammeter, selector switches, ACB / MCCB / MCB of adequate capacity,

indicator lamps duly wired with HRC fuses. The alternator & control panel shall be connected with

provided suitable capacity armoured cable and complete with Acoustic enclosure (canopy) made

out of 16 SWG CRCA Sheet, sound absorbing material Rockwool of 64 density & 100 mm thick

conforming to IS:8183 / PU Foam of 40 Density - at least 40 mm. The resin bonded rockwool

covered from inside the canopy by perforated sheet with 3/4 mm holes, sound level not more than

75 dB at a distance of 1 mtr, as per PVCT norms. Erection, commissioning and satisfactory testing

as per requirement with first filling of fuel, oil, etc. with guarantee / Warrantee of complete system

for Two years. & with obtaining all necessary certificate from Electrical Inspector. The Capacity and

Ratings of DG sets are as below.

(R) Continuous rating of 250 KVA ,BHP not less than 309 BHP

1.2 AMF panel Each 2,20,509.00 1.00

Item no. Description Unit Rate Total Qty. Amount

Providing & erecting approved make AMF control panel suitable for following size of 3 phase,

V., 50 cycles, A.C. diesel generating set complete of scope as detailed below:

1) Power module: A pair of electromechanically interlocked contactors (for mains & generator)

Overload relay for generator contactor Neutral contactor for mains and generator Power socket for

2) Control and metering module: Line voltage monitor. Generator voltage monitor Ammeter 3 items

attempt start facility. Air circuit breakers/MCB/MCCB of suitable rating for auto/manual operation.

Auto/manual switch. Emergency stop push buttons. Manual start push button. frequency meter.

Engine hour meter. Two earthing studs.

3) Protection module: The engine shutdown in the unlikely event of Low lube oil pressure High

cylinder head temperature. V belt failure.

4) Indicators with alarm Load on generator.

5) Indicators Load on mains Engine fails to start . Emergency stop battery charger.

The AMF Panel of following capacity

(D) AMF Control Panel for200 KVA/250 KVA 3 phase DG Set

Sub Total 1.....

Item no. Description Unit Rate Total Qty. Amount

Supply, installation, testing and commissioning of 3 phase 415V 4 wire Free Standing Floor

mounted MV panel made out of minimum 14 SWG CRCA sheet after seventank process and

painting with Epoxy powder coating including all switchgear as detailed below. The panel having

PU/Neoprene rubber gasket of not less than 3mm thickness,separate detachable, gland plate M.S.

base channel, hinged door with locking arrangement for equipment/switchgear. The panel shall

consist of suitable rating FP/TPN Aluminium- busbar-as per SLD (at the rating of 0.8ASq.mm)

supported with DMC/ SMC barriers and colour coded with Heat shrinkable sleeves. The Metering

shall be provided as specified.

The panel shall have Short circuit with standing capacity as given in SLD and consist of the

switchgear as mentioned below. The panel shall be mounted on plinth, stand, etc. including all

materials. The panel shall be got fabricated from manufacturers with CPRI Test certificate only. All

the Panels shall have minimum 25% outgoing as per SLD. The earth bus shall be continuoulsy run

without any jointing/welding and its Size should be per SLD. The size of all Panel Mounting Meters

shall be 96X96mm.The Panels shall be mounted on U channels including supply and fixing of the

same. MCBs shall be provided for Control purposes. (All Panels shall be extendable type only).

Price shall be inclusive following:

Shifting of panels from site store to the suitable location. Installation of panel as located in electrical

drawings or as per site conditions, including removing packing etc. Earthing all components, frame

etc. to a common internal earth bar. Connection, testing & commissioning. Electrical contractor

shall carry out the insulation test at site & all the readings shall be submitted in copy to the

consultant or engineer-in-charge. Supply, installation, testing and commissioning all accessories,

supporting structure, hard ware etc to complete the job. Supply, installation, testing and

commissioning of necessary tools, hard ware, testing hard ware, testing equipment etc. The rates

for the distribution boards apart from the Breakers and instruments shall also include the following :

This schedule of Quantities shall be read in conjuction with the technical specification, General &

Special conditions as well as all tender drawings. Supporting rigid steel framework. Cubicle type,

gauge CRCA sheet steel enclosed.

Proper bonding to earth. Painting/lettering on Breakers and distribution boards, the location they

serve, providing on each panel its circuit diagram.

Providing cable clamps / supports within distribution boards cable alley.

All MCB’s shall be of minimum 10 KA breaking capacity.

The breaking capacity of MCCB’s are mentioned panel wise. All MCCB’s shall be with thermal

magnetic releases upto 250 amps and miroprocesR&B R&B SOR based for 250 amps and above

capacity, unless specified otherwise.

All motor feeders MCCBs shall be of motor duty.

Item no. Description Unit Rate Total Qty. Amount

Distribution panels shall be Powder Coated with Siemens gray paint shade no. RAL-7032 of IS-5.

Degree of protection for following type of distribution panel enclosure shall be as per IS:13947-

IP 4x for all Indoor panel.

IP 65 and double door for all outdoor panel.

All MCCB’s shall be provided with operating mechanism for door interlock.

All measuring instruments (Meters) shall be of digital electronic with LED of approved make.

All hinged door shall be earthed through 2.5 sq mm tinned braided copper wire.

All panels shall have provision of the following:

Pad locking of Switch board doors.All MCB’s used for protection of resistive and lightly inductive

load shall be type “B” characteristic and inductive (motor) load shall be of type “C” characteristic

and discharge lamps and UPS etc. shall be of type D characteristic. All incoming and outgoing air

circuit breakers shall be placed on middle portion of the vertical in single tier formation. SPD as

2.1 SITC OF MAIN PANEL FOR FIRE STATION_HATHIJAN Each 3,25,275.96 1.00

ALSO REFER SLD ALONG WITH THIS. ALL SHOULD BE AS PER SLD & REQUIREMENT.

2.2 SITC OF COMMON AREA FOR SITE_HATHIJAN Each 2,67,965.86 1.00

ALSO REFER SLD ALONG WITH THIS. ALL SHOULD BE AS PER SLD & REQUIREMENT.

2.3 SITC OF PHE PANEL_HATHIJAN Each 84,797.20 1.00

ALSO REFER SLD ALONG WITH THIS. ALL SHOULD BE AS PER SLD & REQUIREMENT.

2.4 SITC OF 1BHK & 2BHK COMMON AREA Each 1,22,320.62 1.00

ALSO REFER SLD ALONG WITH THIS. ALL SHOULD BE AS PER SLD & REQUIREMENT.

2.5 SITC OF DG PANEL_HATHIJAN Each 3,08,467.15 1.00

ALSO REFER SLD ALONG WITH THIS. ALL SHOULD BE AS PER SLD & REQUIREMENT.

2.6 SITC OF EXTERNAL LIGHTING PANEL_HATHIJAN Each 91,779.32 1.00

ALSO REFER SLD ALONG WITH THIS. ALL SHOULD BE AS PER SLD & REQUIREMENT.

2.7 Providing & erecting capacitor duty contactor 3 phase, 415 V with proper connection for following Each 3,217.00 1.00

Item no. Description Unit Rate Total Qty. Amount

2.8 SITC OF APFC PANEL - 75 KVAR Each 2,16,103.00 1.00

Design, Supplying, installing, testing of factory fabricated ready made Three phase APFC Panel

Cubical Panel fabrication should be type tested as per IEC 61921, 61439:1&2 Capacitor Duty

Contactor for switching as per following Steps Incomer Switch of MCCB type Icu=Ics=50KA at

400/440 Volts, with OC, SC, internal earth fault protection Incomer Switch of MCCB type

Icu=Ics=50KA at 400/440 Volts, with OC, SC, internal earth fault protection,Copper tinned insulated

Busbar,Cubical panel should be indoor type with IP 43 and IK 10,Metalized polypropylene film tye3-

phase 550Volt Capacitor,De tuning Reactor for each capacitor,Panel having Short Circuit and

Overload protection,Each step Capacitor having suitable MCB with Sc, OL, internal earth fault

relay,Each stage having Stage Contactor (Capacitor load rating),PF regulator master controller

having suitable steps with LCD display, Rs 485 Communication port, Indication LED Lamps for

main incomer and ON-OFF for each capacitor bank,MS Chanel for Floor mounting, Cable entry as

per site situation,Cooling fans for panel

ALSO REFER SLD ALONG WITH THIS. ALL SHOULD BE AS PER SLD & REQUIREMENT.

[FOR HATHIJAN FIRE STATION]

2.9 SITC OF APFC PANEL - 100 KVAR Each 2,86,018.00 1.00

Design, Supplying, installing, testing of factory fabricated ready made Three phase APFC Panel

Cubical Panel fabrication should be type tested as per IEC 61921, 61439:1&2 Capacitor Duty

Contactor for switching as per following Steps Incomer Switch of MCCB type Icu=Ics=50KA at

400/440 Volts, with OC, SC, internal earth fault protection Incomer Switch of MCCB type

Icu=Ics=50KA at 400/440 Volts, with OC, SC, internal earth fault protection,Copper tinned insulated

Busbar,Cubical panel should be indoor type with IP 43 and IK 10,Metalized polypropylene film tye3-

phase 550Volt Capacitor,De tuning Reactor for each capacitor,Panel having Short Circuit and

Overload protection,Each step Capacitor having suitable MCB with Sc, OL, internal earth fault

relay,Each stage having Stage Contactor (Capacitor load rating),PF regulator master controller

having suitable steps with LCD display, Rs 485 Communication port, Indication LED Lamps for

main incomer and ON-OFF for each capacitor bank,MS Chanel for Floor mounting, Cable entry as

per site situation,Cooling fans for panel

ALSO REFER SLD ALONG WITH THIS. ALL SHOULD BE AS PER SLD & REQUIREMENT.

[FOR COMMON AREA SITE FOR HATHIJAN]

Sub Total 2.....

2a SERVO STABILIZER

Supply, Installation, testing and commissioning of Indoor Type Three phase servo-controlled

voltage stabilizer suitable for input voltage range 340 to 480VAC up to 200 KVA and above

KVA 360-480VAC And output voltage range 415V + 1%. A.C Three Phase. Natural Air Cooled with

Input MCB / MCCB & Bypass switch (L&T, ABB, schneider) , Air cooled up to 60 KVA & above oil

2a.1 Rating : 40 KVA (Air cooled) Each 88,596.00 1.00

2a.2 Rating : 150 KVA (Oil cooled) Each 2,76,862.50 1.00

Sub Total 2a.....

3 JUNCTION BOXES

Item no. Description Unit Rate Total Qty. Amount

3.1 Supply, Transportation, Installation, testing and commissioning of IP-67 Rated weather proof Each 904.42 2.00

Outdoor type junction boxes having dimensdios Height x Width x Depth:- 104 x 104 x 70 mm with

terminal having black colour RAL 7035. with 5 pole terminal set upto 4 sqmm cables

3.2 Supply, Transportation, Installation, testing and commissioning of IP 66/69 weather proof Outdoor Each 4,072.96 5.00

type junction boxeshaving dimensdios Height x Width x Depth:- 155 x 210 x 92 mm with terminal

having black colour RAL 9011. with 5 pole terminal set upto 16 sqmm cables

Sub Total 3.....

4 DISTRIBUTION BOARD

SPN Distribution Board :

4.1 Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface mounted Each 1,141.00 10.00

fitted with busbar, neutral link, earth bar and DIN rail, Conforms to IS 8623-1 & 3, IEC 61439-1 &

without MCB to house appropriate nos. of MCBs.(The DBs should be used of same company of

MCB to be used) suitable for

(A) Single phase incoming and horizontal single phase outgoing

(b) Sheet Steel double door (IP-43)

4.2 Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface mounted Each 1,478.00 68.00

fitted with busbar, neutral link, earth bar and DIN rail, Conforms to IS 8623-1 & 3, IEC 61439-1 &

without MCB to house appropriate nos. of MCBs.(The DBs should be used of same company of

MCB to be used) suitable for

(A) Single phase incoming and horizontal single phase outgoing

(b) Sheet Steel double door (IP-43)

4.3 Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface mounted Each 1,664.00 1.00

fitted with busbar, neutral link, earth bar and DIN rail, Conforms to IS 8623-1 & 3, IEC 61439-1 &

without MCB to house appropriate nos. of MCBs.(The DBs should be used of same company of

MCB to be used) suitable for

(A) Single phase incoming and horizontal single phase outgoing

(b) Sheet Steel double door (IP-43)

TPN Distribution Board :

Item no. Description Unit Rate Total Qty. Amount

4.4 Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface mounted Each 2,885.00 2.00

fitted with busbar, neutral link, earth bar and DIN rail, Conforms to IS 8623-1 & 3, IEC 61439-1 &

without MCB to house appropriate nos. of MCBs.(The DBs should be used of same company of

MCB to be used) suitable for suitable for (PPI DB)

(B) three phase incoming and single phase horizontal type outgoing Per phase isolation

(b) Sheet Steel double door

4.5 Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface mounted Each 3,379.00 30.00

fitted with busbar, neutral link, earth bar and DIN rail, Conforms to IS 8623-1 & 3, IEC 61439-1 &

without MCB to house appropriate nos. of MCBs.(The DBs should be used of same company of

MCB to be used) suitable for suitable for (PPI DB)

(B) three phase incoming and single phase horizontal type outgoing Per phase isolation

(b) Sheet Steel double door

4.6 Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface mounted Each 3,836.00 4.00

fitted with busbar, neutral link, earth bar and DIN rail, Conforms to IS 8623-1 & 3, IEC 61439-1 &

without MCB to house appropriate nos. of MCBs.(The DBs should be used of same company of

MCB to be used) suitable for suitable for (PPI DB)

(B) three phase incoming and single phase horizontal type outgoing Per phase isolation

(b) Sheet Steel double door

4.7 Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface mounted Each 4,620.00 1.00

fitted with busbar, neutral link, earth bar and DIN rail, Conforms to IS 8623-1 & 3, IEC 61439-1 &

without MCB to house appropriate nos. of MCBs.(The DBs should be used of same company of

MCB to be used) suitable for suitable for (PPI DB)

(B) three phase incoming and single phase horizontal type outgoing Per phase isolation

(b) Sheet Steel double door

VTPN Distribution Board :

Item no. Description Unit Rate Total Qty. Amount

4.8 Providing and erecting Sheet Steel powder coated Vertical MCB distribution board (VTPN) - flush / Each 5,760.00 1.00

surface mounted double door (IP54) fitted with copper insulated busbar, isolated neutral bar, earth

bar and DIN rail, Conforms to IS 8623-1 & 3, IEC 61439-1 & 3, suitable for 63/100 AMP TPN

MCCB + RCCB as incomer and three phase outgoing as per following .(The DBs should be used

of same company of MCB to be used)

(A)4 way outgoing

4.9 Providing and erecting Sheet Steel powder coated Vertical MCB distribution board (VTPN) - flush / Each 6,433.00 2.00

surface mounted double door (IP54) fitted with copper insulated busbar, isolated neutral bar, earth

bar and DIN rail, Conforms to IS 8623-1 & 3, IEC 61439-1 & 3, suitable for 63/100 AMP TPN

MCCB + RCCB as incomer and three phase outgoing as per following .(The DBs should be used

of same company of MCB to be used)

(B)6 way outgoing

4.10 Providing and erecting Sheet Steel powder coated Vertical MCB distribution board (VTPN) - flush / Each 8,319.00 4.00

surface mounted double door (IP54) fitted with copper insulated busbar, isolated neutral bar, earth

bar and DIN rail, Conforms to IS 8623-1 & 3, IEC 61439-1 & 3, suitable for 63/100 AMP TPN

MCCB + RCCB as incomer and three phase outgoing as per following .(The DBs should be used

of same company of MCB to be used)

(C)8 way outgoing

4.11 Providing and erecting Sheet Steel powder coated Vertical MCB distribution board (VTPN) - flush / Each 10,857.00 RO

surface mounted double door (IP54) fitted with copper insulated busbar, isolated neutral bar, earth

bar and DIN rail, Conforms to IS 8623-1 & 3, IEC 61439-1 & 3, suitable for 63/100 AMP TPN

MCCB + RCCB as incomer and three phase outgoing as per following .(The DBs should be used

of same company of MCB to be used)

(D)12 way outgoing

MCB 's and its Accessories

4.12 Providing & erecting insulated socket 3P+N+E with Plug16A rating which is comprised of Four pole Each 1,690.00 1.00

MCB slot and insulated socket IP40 Cat-III.

4.13 providing and erecting Miniature circuit breaker single pole 6A to 25A suitable to operate on 240 V Each 111.00 1,320.00

A.C. system and having breaking capacity 10 KA to be erected in existing box. confirming to IS

8828/1996 with ISI Mark Cat.III.

4.14 Providing & erecting 240 V MCB double pole switch for motor & inductive load having 10 KA Each 297.00 1.00

breaking capacity & confirms to IS : 8828 in existing box having following capacity

(A) 6 to 32 Amp.

4.15 Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load having 10KA breaking Each 590.00 31.00

capacity & confirms to IS :8828 in existing box having following capacity

(a) 6 to 32 Amp. ( Cat.III)

Item no. Description Unit Rate Total Qty. Amount

4.16 Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load having 10KA breaking Each 662.00 5.00

capacity & confirms to IS :8828 in existing box having following capacity

(b) 40 Amp. ( Cat.III)

4.17 Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load having 10KA breaking Each 730.00 6.00

capacity & confirms to IS :8828 in existing box having following capacity

(c) 63 Amp. (cat III)

4.18 Providing & erecting 415 V MCB three Pole for Motor & Inductive Load having 10KA breaking Each 582.00 12.00

capacity & confirms to IS :8828 in existing box having following capacity

(a) 6 to 32 Amp. (Cat.III)

4.19 Providing & erecting 415 V MCB three Pole for Motor & Inductive Load having 10KA breaking Each 641.00 1.00

capacity & confirms to IS :8828 in existing box having following capacity

(b)40 Amp.(Cat.III)

4.20 Providing & erecting 415 V MCB three Pole for Motor & Inductive Load having 10KA breaking Each 709.00 1.00

capacity & confirms to IS :8828 in existing box having following capacity

(C)63 Amp. (Cat.III)

4.21 Providing and erecting Approved make RCCBs conforming to IS: 12640 and having sensitivity of Each 1,950.00 88.00

30 mA and Short Circuit withstand capacity of 10 KA and suitable for operation on single phase

V,50Hz. having characteristic of quick action & tripping with all advance feature & do not

incorporate any electronic component. for following Max. rating erected as directed

(i) 25 Amps.DP ( Cat. III)

4.22 Providing and erecting Approved make RCCBs conforming to IS: 12640 and having sensitivity of Each 2,213.00 15.00

30 mA and Short Circuit withstand capacity of 10 KA and suitable for operation on single phase

V,50Hz. having characteristic of quick action & tripping with all advance feature & do not

incorporate any electronic component. for following Max. rating erected as directed

(ii) 40Amps. DP ( Cat. III)

4.23 Providing and erecting Approved make RCCBs conforming to IS: 12640 and having sensitivity of Each 2,628.00 6.00

30 mA and Short Circuit withstand capacity of 10 KA and suitable for operation on single phase

V,50Hz. having characteristic of quick action & tripping with all advance feature & do not

incorporate any electronic component. for following Max. rating erected as directed

(iii) 63Amps. DP ( Cat. III)

4.24 Supplying & erecting approved make RCCB + MCB (Electro magnetic type only) working on Each 1,798.00 72.00

residual current device having 10 KA short circuit breaking capacity and 30 mAmp. Sensitivity &

mili sec. tripping time conforming to IS 12640 test knob facility trip free mechanism operating for

rated leakage at nominal ten volt, complete erected including all materials lugs screws etc.

[a] 6A / 10A / 16A / 20A / 25A 2 pole single phase

Item no. Description Unit Rate Total Qty. Amount

4.25 Supplying & erecting approved make RCCB + MCB (Electro magnetic type only) working on Each 1,925.00 1.00

residual current device having 10 KA short circuit breaking capacity and 30 mAmp. Sensitivity &

mili sec. tripping time conforming to IS 12640 test knob facility trip free mechanism operating for

rated leakage at nominal ten volt, complete erected including all materials lugs screws etc.

[b] 32A / 40A, 2 pole Single Phase

4.26 Supplying & erecting approved make RCCB + MCB (Electro magnetic type only) working on Each 2,145.00 4.00

residual current device having 10 KA short circuit breaking capacity and 30 mAmp. Sensitivity &

mili sec. tripping time conforming to IS 12640 test knob facility trip free mechanism operating for

rated leakage at nominal ten volt, complete erected including all materials lugs screws etc.

[e] 32A to 40 A, 4 Pole Three Phase

4.27 Supplying & erecting approved make RCCB + MCB (Electro magnetic type only) working on Each 2,806.00 1.00

residual current device having 10 KA short circuit breaking capacity and 30 mAmp. Sensitivity &

mili sec. tripping time conforming to IS 12640 test knob facility trip free mechanism operating for

rated leakage at nominal ten volt, complete erected including all materials lugs screws etc.

[f] 63A, 4 pole Three Phase

4.28 SITC of Sheet steel metal enclouser for DP MCB Each 175.00 1.00

4.29 SITC of Sheet steel metal enclouser for FP MCB Each 623.00 1.00

4.30 SITC of 80-100 A FP MCCB with thermal magnetic release. Each 6,723.20 1.00

Note:-1 Add Rs. 10% extra for housing/Encloser of MCCB for Item No 3-4-1 to 3-4-12 (The

Enclosures should be used of same company of MCCBs to be used) *Add 35% additional for

microprocessor type of mccb in place of conventional for item no.3-4-1 to 3-4-12

4.31 SITC of 125A FP MCCB with thermal magnetic release with sheet steel metal enclosure. Each 8,773.60 1.00

Note:-1 Add Rs. 10% extra for housing/Encloser of MCCB for Item No 3-4-1 to 3-4-12 (The

Enclosures should be used of same company of MCCBs to be used) *Add 35% additional for

microprocessor type of mccb in place of conventional for item no.3-4-1 to 3-4-12

4.32 SITC of 200A FP MCCB with thermal magnetic release with sheet steel metal enclosure. Each 17,667.10 2.00

Note:-1 Add Rs. 10% extra for housing/Encloser of MCCB for Item No 3-4-1 to 3-4-12 (The

Enclosures should be used of same company of MCCBs to be used) *Add 35% additional for

microprocessor type of mccb in place of conventional for item no.3-4-1 to 3-4-12

Item no. Description Unit Rate Total Qty. Amount

4.33 SITC of 250A FP MCCB with thermal magnetic release with sheet steel metal enclosure. Each 22,812.90 1.00

Note:-1 Add Rs. 10% extra for housing/Encloser of MCCB for Item No 3-4-1 to 3-4-12 (The

Enclosures should be used of same company of MCCBs to be used) *Add 35% additional for

microprocessor type of mccb in place of conventional for item no.3-4-1 to 3-4-12

4.34 SITC of 315-400A FP MCCB with thermal magnetic release with sheet steel metal enclosure. Each 27,476.90 2.00

Note:-1 Add Rs. 10% extra for housing/Encloser of MCCB for Item No 3-4-1 to 3-4-12 (The

Enclosures should be used of same company of MCCBs to be used) *Add 35% additional for

microprocessor type of mccb in place of conventional for item no.3-4-1 to 3-4-12

4.35 SITC of IP 65 - outdoor type - 4Way SPN DB Each 1,833.45 1.00

4.36 SITC of IP 65 - outdoor type - 8Way SPN DB Each 2,891.68 1.00

4.37 SITC of Blank Plates Each 9.00 84.00

4.38 Supplying and fixing 20 A, 240 V, SPN Industrial type socket outlet, with 2 pole and earth, metal Each 2,024.17 10.00

encloused plug top alongwith 20 A "C" curve, SP, MCB, in sheet steel enclosure, on surface or in

recess, with chained metal cover for the socket out let and complete with connections, testing and

commissioning etc. as required.

Sub Total 4.....

5 LT CABLES & CABLE TERMINATION

5.1 UNARMOURED COPPER CABLES.

5.1.1 Supplying & erecting XLPE(IS:7098)(I)-88 ISI unarmoured copper cable 1.1 KV grade to be Mtr. 136.00 50.00

erected as directed of following size.

(E) 3 core 2.5 Sq. mm

5.1.2 Supplying & erecting XLPE(IS:7098)(I)-88 ISI unarmoured copper cable 1.1 KV grade to be Mtr. 187.00 10.00

erected as directed of following size.

(F) 3 core 4 Sq. mm

5.1.3 Supplying & erecting XLPE(IS:7098)(I)-88 ISI unarmoured copper cable 1.1 KV grade to be Mtr. 290.00 500.00

erected as directed of following size.

(G) 3 core 6 Sq. mm

5.1.4 Supplying & erecting XLPE(IS:7098)(I)-88 ISI unarmoured copper cable 1.1 KV grade to be Mtr. 167.00 10.00

erected as directed of following size.

(J) 4 core 2.5 Sq. mm

5.1.5 Supplying & erecting XLPE(IS:7098)(I)-88 ISI unarmoured copper cable 1.1 KV grade to be Mtr. 238.00 10.00

erected as directed of following size.

(K) 4 core 4 Sq. mm

Item no. Description Unit Rate Total Qty. Amount

5.1.6 Supplying & erecting XLPE(IS:7098)(I)-88 ISI unarmoured copper cable 1.1 KV grade to be Mtr. 361.00 10.00

erected as directed of following size.

(L) 4 core 6 Sq. mm

5.1.7 Supplying & erecting XLPE(IS:7098)(I)-88 ISI unarmoured copper cable 1.1 KV grade to be Mtr. 568.00 10.00

erected as directed of following size.

(M) 4 core 10 Sq. mm

5.2 ARMOURED ALUMINIUM CABLES

5.2.1 Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand Aluminium Mtr. 152.00 10.00

conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of

following size of cables

(A) 4 core 16 Sq. mm

5.2.2 Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand / Solid Aluminium Mtr. 139.00 10.00

conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of

following size of cables

(C) 4 core 10 Sq. mm

5.2.3 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium Mtr. 182.00 10.00

conductor with water swellable coating which should protect against saline water & for 1.1 KV. to

be laid on wall with necessary clamps or in existing trench / pipe of following size of cables

(I) 3 1/2 core 25 Sq. mm( 16 Sq. mm 1/2 core)

5.2.4 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium Mtr. 218.00 260.00

conductor with water swellable coating which should protect against saline water & for 1.1 KV. to

be laid on wall with necessary clamps or in existing trench / pipe of following size of cables

(I) 3 1/2 core 35 Sq. mm( 25 Sq. mm 1/2 core)

5.2.5 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium Mtr. 282.00 10.00

conductor with water swellable coating which should protect against saline water & for 1.1 KV. to

be laid on wall with necessary clamps or in existing trench / pipe of following size of cables

(C) 3 1/2 core 50 Sq. mm ( 25 Sq.1/2 mm core)

Item no. Description Unit Rate Total Qty. Amount

5.2.6 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium Mtr. 375.00 10.00

conductor with water swellable coating which should protect against saline water & for 1.1 KV. to

be laid on wall with necessary clamps or in existing trench / pipe of following size of cables

(D) 3 1/2 core 70 Sq. mm ( 35 Sq. mm 1/2 core)

5.2.7 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium Mtr. 486.00 15.00

conductor with water swellable coating which should protect against saline water & for 1.1 KV. to

be laid on wall with necessary clamps or in existing trench / pipe of following size of cables

(E) 3 1/2 core 95 Sq. mm ( 50 Sq. mm 1/2 core)

5.2.8 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium Mtr. 535.00 75.00

conductor with water swellable coating which should protect against saline water & for 1.1 KV. to

be laid on wall with necessary clamps or in existing trench / pipe of following size of cables

(F) 3 1/2 core 120 Sq. mm ( 70 Sq. mm 1/2 core)

5.2.9 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium Mtr. 724.00 260.00

conductor with water swellable coating which should protect against saline water & for 1.1 KV. to

be laid on wall with necessary clamps or in existing trench / pipe of following size of cables

(G) 3 1/2 core 150 Sq. mm ( 70 Sq. mm 1/2 core)

5.2.10 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium Mtr. 896.00 610.00

conductor with water swellable coating which should protect against saline water & for 1.1 KV. to

be laid on wall with necessary clamps or in existing trench / pipe of following size of cables

(H) 3 1/2 core 185 Sq. mm ( 95 Sq. mm 1/2 core)

5.2.11 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium Mtr. 1,157.00 100.00

conductor with water swellable coating which should protect against saline water & for 1.1 KV. to

be laid on wall with necessary clamps or in existing trench / pipe of following size of cables

(I) 3 1/2 core 240 Sq. mm( 120 Sq. mm 1/2 core)

Item no. Description Unit Rate Total Qty. Amount

5.2.12 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium Mtr. 1,394.00 10.00

conductor with water swellable coating which should protect against saline water & for 1.1 KV. to

be laid on wall with necessary clamps or in existing trench / pipe of following size of cables

(I) 3 1/2 core 300 Sq. mm( 150 Sq. mm 1/2 core)

5.3 ARMOURED COPPER CABLES

5.3.1 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Copper conductor Mtr. 213.00 50.00

with water swellable coating which should protect against saline water & 1.1 KV. to be laid on wall

with necessary clamps or in existing trench / pipe at road crossing or floor of following size of

(A) 3 core 2.5Sq. Mm

5.3.2 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Copper conductor Mtr. 285.00 365.00

with water swellable coating which should protect against saline water & 1.1 KV. to be laid on wall

with necessary clamps or in existing trench / pipe at road crossing or floor of following size of

(B) 3 core 4 Sq. mm

5.3.3 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Copper conductor Mtr. 392.00 10.00

with water swellable coating which should protect against saline water & 1.1 KV. to be laid on wall

with necessary clamps or in existing trench / pipe at road crossing or floor of following size of

(C) 3 core 6 Sq. mm

5.3.4 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Copper conductor Mtr. 495.00 10.00

with water swellable coating which should protect against saline water & 1.1 KV. to be laid on wall

with necessary clamps or in existing trench / pipe at road crossing or floor of following size of

(C) 3 core 10 Sq. mm

5.3.5 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Copper conductor Mtr. 269.00 10.00

with water swellable coating which should protect against saline water & 1.1 KV. to be laid on wall

with necessary clamps or in existing trench / pipe at road crossing or floor of following size of

(A) 4 core 2.5 Sq. mm

Item no. Description Unit Rate Total Qty. Amount

5.3.6 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Copper conductor Mtr. 361.00 315.00

with water swellable coating which should protect against saline water & 1.1 KV. to be laid on wall

with necessary clamps or in existing trench / pipe at road crossing or floor of following size of

(B) 4 core 4 Sq. mm

5.3.7 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Copper conductor Mtr. 505.00 705.00

with water swellable coating which should protect against saline water & 1.1 KV. to be laid on wall

with necessary clamps or in existing trench / pipe at road crossing or floor of following size of

(C) 4 core 6 Sq. mm

5.3.8 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Copper conductor Mtr. 670.00 160.00

with water swellable coating which should protect against saline water & 1.1 KV. to be laid on wall

with necessary clamps or in existing trench / pipe at road crossing or floor of following size of

(A) 4 core 10 Sq. mm

5.3.9 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Copper conductor Mtr. 978.00 105.00

with water swellable coating which should protect against saline water & 1.1 KV. to be laid on wall

with necessary clamps or in existing trench / pipe at road crossing or floor of following size of

(B) 4 core 16 Sq. mm

5.4 CABLE GLANDS.

5.4.1 Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated Ea. 33.00 40.00

armoured cable complete with out going tails, insulating tape etc for following size of cables.

(A) 2 to 4 core 2.5/4 Sq. mm

5.4.2 Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated Ea. 38.00 24.00

armoured cable complete with out going tails, insulating tape etc for following size of cables.

(B) 2 to 4 core 6 Sq. mm

5.4.3 Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated Ea. 38.00 8.00

armoured cable complete with out going tails, insulating tape etc for following size of cables.

(C) 2 to 4 core 10 Sq. mm

Item no. Description Unit Rate Total Qty. Amount

5.4.4 Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated Ea. 47.00 6.00

armoured cable complete with out going tails, insulating tape etc for following size of cables.

(D) 2 to 4 core 16 Sq. mm

5.4.5 Providing and, fixing heavy duty flange type brass double compression type cable gland with Ea. 66.00 2.00

rubber ring for PVC insulated armoured cable complete with out going tails, insulating tape etc for

following size of cables.

(B) 3 & 1/2 core 25Sq. mm

5.4.6 Providing and, fixing heavy duty flange type brass double compression type cable gland with Ea. 75.00 8.00

rubber ring for PVC insulated armoured cable complete with out going tails, insulating tape etc for

following size of cables.

(B) 3 & 1/2 core 35/50 Sq. mm

5.4.7 Providing and, fixing heavy duty flange type brass double compression type cable gland with Ea. 102.00 2.00

rubber ring for PVC insulated armoured cable complete with out going tails, insulating tape etc for

following size of cables.

(C) 3 & 1/2 core 70 Sq. mm

5.4.8 Providing and, fixing heavy duty flange type brass double compression type cable gland with Ea. 130.00 2.00

rubber ring for PVC insulated armoured cable complete with out going tails, insulating tape etc for

following size of cables.

(D) 3 & 1/2 core 95 Sq. mm

5.4.9 Providing and, fixing heavy duty flange type brass double compression type cable gland with Ea. 139.00 4.00

rubber ring for PVC insulated armoured cable complete with out going tails, insulating tape etc for

following size of cables.

(E) 3 & 1/2 core 120 Sq. mm

5.4.10 Providing and, fixing heavy duty flange type brass double compression type cable gland with Ea. 189.00 6.00

rubber ring for PVC insulated armoured cable complete with out going tails, insulating tape etc for

following size of cables.

(F) 3 & 1/2 core 150 Sq. mm

5.4.11 Providing and, fixing heavy duty flange type brass double compression type cable gland with Ea. 236.00 10.00

rubber ring for PVC insulated armoured cable complete with out going tails, insulating tape etc for

following size of cables.

(G) 3 & 1/2 core 185 Sq. mm

Item no. Description Unit Rate Total Qty. Amount

5.4.12 Providing and, fixing heavy duty flange type brass double compression type cable gland with Ea. 245.00 4.00

rubber ring for PVC insulated armoured cable complete with out going tails, insulating tape etc for

following size of cables.

(H) 3 & 1/2 core 240 Sq. mm

5.4.13 Providing and, fixing heavy duty flange type brass double compression type cable gland with Ea. 278.00 2.00

rubber ring for PVC insulated armoured cable complete with out going tails, insulating tape etc for

following size of cables.

(I) 3 & 1/2 core 300 Sq. mm

5.5 Aluminium lugs

5.5.1 Supply, installation, testing and commissioning of Solder less crimping type Aluminium lugs Ea. 13.00 4.00

conforming to IS suitable for cable of following size evenly crimped with high pressure tool &

connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner.

5.5.2 Supply, installation, testing and commissioning of Solder less crimping type Aluminium lugs Ea. 15.00 4.00

conforming to IS suitable for cable of following size evenly crimped with high pressure tool &

connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner.

5.5.3 Supply, installation, testing and commissioning of Solderless crimping type Aluminium lugs Ea. 20.00 32.00

conforming to IS suitable for cable of following size evenly crimped with high pressure tool &

connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner.

5.5.4 Supply, installation, testing and commissioning of Solderless crimping type Aluminium lugs Ea. 25.00 8.00

conforming to IS suitable for cable of following size evenly crimped with high pressure tool &

connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner.

5.5.5 Supply, installation, testing and commissioning of Solderless crimping type Aluminium lugs Ea. 40.00 8.00

conforming to IS suitable for cable of following size evenly crimped with high pressure tool &

connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner.

Item no. Description Unit Rate Total Qty. Amount

5.5.6 Supply, installation, testing and commissioning of Solderless crimping type Aluminium lugs Ea. 45.00 16.00

conforming to IS suitable for cable of following size evenly crimped with high pressure tool &

connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner.

5.5.7 Supply, installation, testing and commissioning of Solderless crimping type Aluminium lugs Ea. 61.00 24.00

conforming to IS suitable for cable of following size evenly crimped with high pressure tool &

connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner.

5.5.8 Supply, installation, testing and commissioning of Solderless crimping type Aluminium lugs Ea. 80.00 40.00

conforming to IS suitable for cable of following size evenly crimped with high pressure tool &

connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner.

5.5.9 Supply, installation, testing and commissioning of Solderless crimping type Aluminium lugs Ea. 85.00 16.00

conforming to IS suitable for cable of following size evenly crimped with high pressure tool &

connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner.

5.5.10 Supply, installation, testing and commissioning of Solderless crimping type Aluminium lugs Ea. 98.00 8.00

conforming to IS suitable for cable of following size evenly crimped with high pressure tool &

connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner.

5.6 Copper lugs

5.6.1 Supply, installation, testing and commissioning of Solder less crimping type Copper lugs Ea. 8.00 256.00

conforming to IS suitable for cable of following size evenly crimped with high pressure tool &

connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner.

Item no. Description Unit Rate Total Qty. Amount

5.6.2 Supply, installation, testing and commissioning of Solder less crimping type Copper lugs Ea. 10.00 32.00

conforming to IS suitable for cable of following size evenly crimped with high pressure tool &

connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner.

5.6.3 Supply, installation, testing and commissioning of Solder less crimping type Copper lugs Ea. 12.00 24.00

conforming to IS suitable for cable of following size evenly crimped with high pressure tool &

connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner.

Sub Total 5.....

Perforated type cable tray

6.1 Providing and fixing approved make Perforated C type cable tray. Made from sheet steel. The Rmt 357.00 20.00

cable tray should be single or double bended as per required and as per IS 2062/1079 and shall be

coated with hot dip galvanizing as per IS 2629/4759. with max 17.5% perforation with coupler plate

/ Fish plate and GI hardware like nut - bolt and washers etc. erection with necessary support(

included) as per Specification and as per instruction of engineer in charge..

(2) 100 X 50 X 1.6 mm Thick

6.2 Providing and fixing approved make Perforated C type cable tray. Made from sheet steel. The Rmt 420.00 90.00

cable tray should be single or double bended as per required and as per IS 2062/1079 and shall be

coated with hot dip galvanizing as per IS 2629/4759. with max 17.5% perforation with coupler plate

/ Fish plate and GI hardware like nut - bolt and washers etc. erection with necessary support(

included) as per Specification and as per instruction of engineer in charge..

(3) 150 X 50 X 1.6 mm Thick

6.3 Providing and fixing approved make Perforated C type cable tray. Made from sheet steel. The Rmt 616.00 10.00

cable tray should be single or double bended as per required and as per IS 2062/1079 and shall be

coated with hot dip galvanizing as per IS 2629/4759. with max 17.5% perforation with coupler plate

/ Fish plate and GI hardware like nut - bolt and washers etc. erection with necessary support(

included) as per Specification and as per instruction of engineer in charge.

(5) 300 X 50 X 2.0 mm Thick

Item no. Description Unit Rate Total Qty. Amount

6.4 Providing and fixing approved make 'T' Junction for Perforated C type cable tray. Made from Ea. 158.00 2.00

sheet steel. The Junction should be bended as per IS 2062/1079 and shall be coated with hot dip

galvanizing as per IS 2629/4759. with max 17.5% perforation with coupler plate / Fish plate and GI

hardware like nut - bolt and washers etc. erected on existing support as per Specification and as

per instruction of engineer in charge of following size

(2) 100 X 50 X 1.6 mm Thick

6.5 Providing and fixing approved make 'T' Junction for Perforated C type cable tray. Made from Ea. 183.00 5.00

sheet steel. The Junction should be bended as per IS 2062/1079 and shall be coated with hot dip

galvanizing as per IS 2629/4759. with max 17.5% perforation with coupler plate / Fish plate and GI

hardware like nut - bolt and washers etc. erected on existing support as per Specification and as

per instruction of engineer in charge of following size

(3) 150 X 50 X 1.6 mm Thick ' T' Junction

6.6 Providing and fixing approved make 'T' Junction for Perforated C type cable tray. Made from Ea. 289.00 2.00

sheet steel. The Junction should be bended as per IS 2062/1079 and shall be coated with hot dip

galvanizing as per IS 2629/4759. with max 17.5% perforation with coupler plate / Fish plate and GI

hardware like nut - bolt and washers etc. erected on existing support as per Specification and as

per instruction of engineer in charge of following size

(5) 300 X 50 X 2.0 mm Thick ' T' Junction

6.7 Providing and fixing approved make '90° Elbow' for Perforated C type cable tray. Made from Ea. 115.00 3.00

sheet steel. The Junction should be bended as per IS 2062/1079 and shall be coated with hot dip

galvanizing as per IS 2629/4759. with coupler plate / Fish plate and GI hardware like nut - bolt and

washers etc. erected on existing support as per Specification and as per instruction of engineer in

(2)100 X 50 X 1.6 mm Thick 90° Elbow

6.8 Providing and fixing approved make '90° Elbow' for Perforated C type cable tray. Made from Ea. 162.00 14.00

sheet steel. The Junction should be bended as per IS 2062/1079 and shall be coated with hot dip

galvanizing as per IS 2629/4759. with coupler plate / Fish plate and GI hardware like nut - bolt and

washers etc. erected on existing support as per Specification and as per instruction of engineer in

(3)150 X 50 X 1.6 mm Thick 90° Elbow

6.9 Providing and fixing approved make '90° Elbow' for Perforated C type cable tray. Made from Ea. 243.00 3.00

sheet steel. The Junction should be bended as per IS 2062/1079 and shall be coated with hot dip

galvanizing as per IS 2629/4759. with coupler plate / Fish plate and GI hardware like nut - bolt and

washers etc. erected on existing support as per Specification and as per instruction of engineer in

(5) 300 X 50 X 2.0 mm Thick 90° Elbow

Item no. Description Unit Rate Total Qty. Amount

6.10 Providing and fixing approved make 'Cross over Junction' for Perforated C type cable tray. Ea. 213.00 1.00

Made from sheet steel. The Junction should be bended as per IS 2062/1079 and shall be coated

with hot dip galvanizing as per IS 2629/4759. with max 17.5% perforation with coupler plate / Fish

plate and GI hardware like nut - bolt and washers etc. erected on existing support as per

Specification and as per instruction of engineer in charge..

(2) 100 X 50 X 1.6 mm Thick Cross Junction

6.11 Providing and fixing approved make 'Cross over Junction' for Perforated C type cable tray. Ea. 242.00 2.00

Made from sheet steel. The Junction should be bended as per IS 2062/1079 and shall be coated

with hot dip galvanizing as per IS 2629/4759. with max 17.5% perforation with coupler plate / Fish

plate and GI hardware like nut - bolt and washers etc. erected on existing support as per

Specification and as per instruction of engineer in charge..

(3) 150 X 50 X 1.6 mm Thick Cross Junction

6.12 Providing and fixing approved make 'Cross over Junction' for Perforated C type cable tray. Ea. 370.00 1.00

Made from sheet steel. The Junction should be bended as per IS 2062/1079 and shall be coated

with hot dip galvanizing as per IS 2629/4759. with max 17.5% perforation with coupler plate / Fish

plate and GI hardware like nut - bolt and washers etc. erected on existing support as per

Specification and as per instruction of engineer in charge..

(5) 300 X 50 X 2.0mm Thick Cross Junction

Ladder type cable tray

6.13 Providing and fixing approved make Ladder type cable tray. Made from M.S sheet. The cable tray Mtr. 518.00 110.00

should be bended as per IS 2062/1079 shall be fabricated of double bended channel section

longitudinal members with single bended Channel section. Rungs of members welded to the base

of the longitudinal members at 250 mm c/c spacing . as per IS and shall be coated with hot dip

galvanizing as per IS 2629/4759. with coupler plate / Fish plate and GI hardware like nut - bolt and

washers etc. erected on existing support as per Specification and as per instruction of engineer in

(8) 150 X 100 X 1.6 mm Thick

6.14 Providing and fixing approved make Ladder type cable tray. Made from M.S sheet. The cable tray Mtr. 530.00 35.00

should be bended as per IS 2062/1079 shall be fabricated of double bended channel section

longitudinal members with single bended Channel section. Rungs of members welded to the base

of the longitudinal members at 250 mm c/c spacing . as per IS and shall be coated with hot dip

galvanizing as per IS 2629/4759. with coupler plate / Fish plate and GI hardware like nut - bolt and

washers etc. erected on existing support as per Specification and as per instruction of engineer in

(9) 200 X 100 X 1.6 mm Thick

Item no. Description Unit Rate Total Qty. Amount

6.15 Providing and fixing approved make Ladder type cable tray. Made from M.S sheet. The cable tray Mtr. 551.00 20.00

should be bended as per IS 2062/1079 shall be fabricated of double bended channel section

longitudinal members with single bended Channel section. Rungs of members welded to the base

of the longitudinal members at 250 mm c/c spacing . as per IS and shall be coated with hot dip

galvanizing as per IS 2629/4759. with coupler plate / Fish plate and GI hardware like nut - bolt and

washers etc. erected on existing support as per Specification and as per instruction of engineer in

(10) 300 X 100 X 2.0 mm Thick

6.16 Providing and fixing approved make Ladder type cable tray. Made from M.S sheet. The cable tray Mtr. 658.00 170.00

should be bended as per IS 2062/1079 shall be fabricated of double bended channel section

longitudinal members with single bended Channel section. Rungs of members welded to the base

of the longitudinal members at 250 mm c/c spacing . as per IS and shall be coated with hot dip

galvanizing as per IS 2629/4759. with coupler plate / Fish plate and GI hardware like nut - bolt and

washers etc. erected on existing support as per Specification and as per instruction of engineer in

(12) 500 X 100 X 2.0 mm Thick

6.17 Providing and fixing approved make Ladder type cable tray. Made from M.S sheet. The cable tray Mtr. 688.00 50.00

should be bended as per IS 2062/1079 shall be fabricated of double bended channel section

longitudinal members with single bended Channel section. Rungs of members welded to the base

of the longitudinal members at 250 mm c/c spacing . as per IS and shall be coated with hot dip

galvanizing as per IS 2629/4759. with coupler plate / Fish plate and GI hardware like nut - bolt and

washers etc. erected on existing support as per Specification and as per instruction of engineer in

(13) 600 X 100 X 2.0 mm Thick

6.18 Providing and fixing approved make 'T' Junction for ladder type cable tray. Made from M.S Ea. 619.00 2.00

sheet steel. The Junction should be bended as per IS 2062/1079. with coupler plate / Fish plate

and GI hardware like nut - bolt and washers etc. erected on existing support as per Specification

and as per instruction of engineer in charge..

(8) 150 X 100 X 1.5 mm Thick 'T' Junction

6.19 Providing and fixing approved make 'T' Junction for ladder type cable tray. Made from M.S Ea. 653.00 3.00

sheet steel. The Junction should be bended as per IS 2062/1079. with coupler plate / Fish plate

and GI hardware like nut - bolt and washers etc. erected on existing support as per Specification

and as per instruction of engineer in charge..

(9) 200 X 100 X 1.5 mm Thick 'T' Junction

Item no. Description Unit Rate Total Qty. Amount

6.20 Providing and fixing approved make 'T' Junction for ladder type cable tray. Made from M.S Ea. 700.00 4.00

sheet steel. The Junction should be bended as per IS 2062/1079. with coupler plate / Fish plate

and GI hardware like nut - bolt and washers etc. erected on existing support as per Specification

and as per instruction of engineer in charge..

(10) 300 X 100 X 2.0 mm Thick 'T' Junction

6.21 Providing and fixing approved make 'T' Junction for ladder type cable tray. Made from M.S Ea. 967.00 2.00

sheet steel. The Junction should be bended as per IS 2062/1079. with coupler plate / Fish plate

and GI hardware like nut - bolt and washers etc. erected on existing support as per Specification

and as per instruction of engineer in charge..

(12) 500 X 100 X 2.0 mm Thick 'T' Junction

6.22 Providing and fixing approved make 'T' Junction for ladder type cable tray. Made from M.S Ea. 1,077.00 2.00

sheet steel. The Junction should be bended as per IS 2062/1079. with coupler plate / Fish plate

and GI hardware like nut - bolt and washers etc. erected on existing support as per Specification

and as per instruction of engineer in charge..

(13) 600 X 100 X 2.0 mm Thick 'T' Junction

6.23 Providing and fixing approved make '90° Elbow' for ladder type cable tray. Made from M.S Ea. 437.00 4.00

sheet steel. The Junction should be bended as per IS 2062/1079. with coupler plate / Fish plate

and GI hardware like nut - bolt and washers etc. erected on existing support as per Specification

and as per instruction of engineer in charge..

(8) 150 X 100 X 1.6 mm Thick

6.24 Providing and fixing approved make '90° Elbow' for ladder type cable tray. Made from M.S Ea. 467.00 5.00

sheet steel. The Junction should be bended as per IS 2062/1079. with coupler plate / Fish plate

and GI hardware like nut - bolt and washers etc. erected on existing support as per Specification

and as per instruction of engineer in charge..

(9) 200 X 100 X 2.0 mm Thick

6.25 Providing and fixing approved make '90° Elbow' for ladder type cable tray. Made from M.S Ea. 531.00 6.00

sheet steel. The Junction should be bended as per IS 2062/1079. with coupler plate / Fish plate

and GI hardware like nut - bolt and washers etc. erected on existing support as per Specification

and as per instruction of engineer in charge..

(10) 300 X 100 X 2.0 mm Thick

Item no. Description Unit Rate Total Qty. Amount

6.26 Providing and fixing approved make '90° Elbow' for ladder type cable tray. Made from M.S Ea. 721.00 3.00

sheet steel. The Junction should be bended as per IS 2062/1079. with coupler plate / Fish plate

and GI hardware like nut - bolt and washers etc. erected on existing support as per Specification

and as per instruction of engineer in charge..

(12) 500 X 100 X 2.0 mm Thick

6.27 Providing and fixing approved make '90° Elbow' for ladder type cable tray. Made from M.S Ea. 806.00 3.00

sheet steel. The Junction should be bended as per IS 2062/1079. with coupler plate / Fish plate

and GI hardware like nut - bolt and washers etc. erected on existing support as per Specification

and as per instruction of engineer in charge..

(13) 600 X 100 X 2.0 mm Thick

6.28 Providing and fixing approved make 'Cross over Junction' for ladder type cable tray. Made from Ea. 729.00 2.00

sheet steel. The Junction should be bended as per IS 2062/1079 and shall be coated with hot dip

galvanizing as per IS 2629/4759. with coupler plate / Fish plate and GI hardware like nut - bolt and

washers etc. erected on existing support as per Specification and as per instruction of engineer in

(8) 150 X 100 X 1.6 mm Thick

6.29 Providing and fixing approved make 'Cross over Junction' for ladder type cable tray. Made from Ea. 759.00 2.00

sheet steel. The Junction should be bended as per IS 2062/1079 and shall be coated with hot dip

galvanizing as per IS 2629/4759. with coupler plate / Fish plate and GI hardware like nut - bolt and

washers etc. erected on existing support as per Specification and as per instruction of engineer in

(9) 200 X 100 X 2.0 mm Thick

6.30 Providing and fixing approved make 'Cross over Junction' for ladder type cable tray. Made from Ea. 823.00 1.00

sheet steel. The Junction should be bended as per IS 2062/1079 and shall be coated with hot dip

galvanizing as per IS 2629/4759. with coupler plate / Fish plate and GI hardware like nut - bolt and

washers etc. erected on existing support as per Specification and as per instruction of engineer in

(10) 300 X 100 X 2.0 mm Thick

6.31 Providing and fixing approved make 'Cross over Junction' for ladder type cable tray. Made from Ea. 1,069.00 1.00

sheet steel. The Junction should be bended as per IS 2062/1079 and shall be coated with hot dip

galvanizing as per IS 2629/4759. with coupler plate / Fish plate and GI hardware like nut - bolt and

washers etc. erected on existing support as per Specification and as per instruction of engineer in

(12) 500 X 100 X 2.0 mm Thick

Item no. Description Unit Rate Total Qty. Amount

6.32 Providing and fixing approved make 'Cross over Junction' for ladder type cable tray. Made from Ea. 1,174.00 1.00

sheet steel. The Junction should be bended as per IS 2062/1079 and shall be coated with hot dip

galvanizing as per IS 2629/4759. with coupler plate / Fish plate and GI hardware like nut - bolt and

washers etc. erected on existing support as per Specification and as per instruction of engineer in

(13) 600 X 100 X 2.0 mm Thick

6.33 Supplying , fabricating and installation of various sizes clamps for cable tray supports using Kg 77.00 890.00

available M.S. sections & rod as per drawings or instructions of engineer in charge or consultant

including applying zinc chromate yellow oxide and two to three coats of required enamel paints with

anchor fasteners etc.

Sub Total 6.....

7 INTERNAL WIRING

7.1 Point wiring for Tissino / Modular secondary light point with 2-1.5 sq.mm & earth wire of Pt. 174.30 1,210.00

1.5 sq.mm (green) both are of ISI marked 1.1 KV grade ZHFR/ HRFR PVC insulated multi strand

copper wires, in below type of pipe to be erected complete with earth continuity and necessary

connection with primary light with accessories erected on Metal / PVC / wooden box covered with

3 mm thick PC(Polycarbonate) / Acrylic sheet for open / concealed wiring. with necessary Lamp

holder / ceiling rose / H.D.Connector as directed.

(f) with medium class Rigid PVC pipe and accessories erected concealed in wall/ceiling complete

NOTE:1. For use of ZHFR/HRFR Copper wires in place of FRLS PVC wires add 5% in Item of

Point wiring Item No 1-1-1 to 1-2-6 & 1-5-1 & 1-5-2.

7.2 Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (Green) both are of Pt. 505.05 900.00

ISI marked 1.1 KV grade ZHFR/ HRFR PVC insulated multi strand copper wires up to 10 mtr

length , in below type of pipe erected with 6A Modular type switch / bell push & accessories and

earth continuity of following type, erected on PVC / Metallic/Wooden box, single mounting base

frame covered with textured/metallic/white front plate modules erected on / in wall / ceiling as per

pipe erected, with necessary Lamp holder/ceiling rose / H.D.Connector as directed.

(f) with medium class Rigid PVC pipe and accessories erected concealed in wall/ceiling

complete(cat lll)

NOTE:1. For use of ZHFR/HRFR Copper wires in place of FRLS PVC wires add 5% in Item of

Point wiring Item No 1-1-1 to 1-2-6 & 1-5-1 & 1-5-2.

Item no. Description Unit Rate Total Qty. Amount

7.3 Point wiring for FAN with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (Green) both are of .ISI Pt. 701.40 380.00

marked 1.1 KV Grade ZHFR/ HRFR PVC insulated multi strand copper wires up to 10 mtr length,

in below type of pipe erected with 6A Modular type switch and hum free EME step type electronic

fan regulator mounted and accessories with earth continuity of following type erected on PVC /

Metallic/Wooden box, single mounting base frame covered with textured/metallic/white front plate

modules erected on / in wall / ceiling as per pipe erected. with necessary ceiling rose /

H.D.Connector as directed.

(f) with medium class Rigid PVC pipe and accessories erected concealed in wall/ceiling

complete(cat III)

NOTE:1. For use of ZHFR/HRFR Copper wires in place of FRLS PVC wires add 5% in Item of

Point wiring Item No 1-1-1 to 1-2-6 & 1-5-1 & 1-5-2.

7.4 Point wiring for Individual Plug with & earth wire of 1.5 sq.mm (Green) both are of ISI marked Pt. 530.25 1,100.00

1.1 KV grade ZHFR/ HRFR PVC insulated multi strand copper wires up to 10 mtr length, in below

type of pipe erected complete with Modular type switch & 5 pin Plug erected on PVC /

Metallic/Wooden box covered with appropriate front plate modules erected on / in wall / ceiling as

per pipe erected with following type of accessories.

[I] For 6A Plug and 6 a switch with 2-1.5 sq.mm Cu. Wire from nearby switchboard/mcb db

(f) with medium class Rigid PVC pipe and accessories erected concealed in wall/ceiling

complete (cat III)

NOTE:1. For use of ZHFR/HRFR Copper wires in place of FRLS PVC wires add 5% in Item of

Point wiring Item No 1-1-1 to 1-2-6 & 1-5-1 & 1-5-2.

7.5 Point wiring for Individual Plug with & earth wire of 1.5 sq.mm (Green) both are of ISI marked Pt. 774.90 315.00

1.1 KV grade ZHFR/ HRFR PVC insulated multi strand copper wires up to 10 mtr length, in below

type of pipe erected complete with Modular type switch & 5 pin Plug erected on PVC /

Metallic/Wooden box covered with appropriate front plate modules erected on / in wall / ceiling as

per pipe erected with following type of accessories.

[II] For 16A Plug and 16 amp switch with 2-2.5 sq.mm Cu. Wire from mcb db board.

(f) with medium class Rigid PVC pipe and accessories erected concealed in wall/ceiling

complete (cat III)

NOTE:1. For use of ZHFR/HRFR Copper wires in place of FRLS PVC wires add 5% in Item of

Point wiring Item No 1-1-1 to 1-2-6 & 1-5-1 & 1-5-2.

Item no. Description Unit Rate Total Qty. Amount

7.6 Point wiring for Individual Plug with & earth wire of 1.5 sq.mm (Green) both are of ISI marked Pt. 906.15 345.00

1.1 KV grade ZHFR/ HRFR PVC insulated multi strand copper wires up to 10 mtr length, in below

type of pipe erected complete with Modular type switch & 5 pin Plug erected on PVC /

Metallic/Wooden box covered with appropriate front plate modules erected on / in wall / ceiling as

per pipe erected with following type of accessories.

[III] For 16A Plug and 16 amp switch with 2-4 sq.mm Cu. Wire with 2.5 sq.mm ( green)

earthing wire from mcb d b board.

(f) with medium class Rigid PVC pipe and accessories erected concealed in wall/ceiling

complete (cat III)

NOTE:1. For use of ZHFR/HRFR Copper wires in place of FRLS PVC wires add 5% in Item of

Point wiring Item No 1-1-1 to 1-2-6 & 1-5-1 & 1-5-2.

7.7 Point wiring for on board Looped Plug with 6A Modular type switch & 5 pin socket erected on PVC Pt. 267.75 585.00

/ Metallic/Wooden box, single mounting base frame covered with textured / metallic/white front

plate modules erected on / in wall / ceiling with following type accessories

NOTE:1. For use of ZHFR/HRFR Copper wires in place of FRLS PVC wires add 5% in Item of

Point wiring Item No 1-1-1 to 1-2-6 & 1-5-1 & 1-5-2.

7.8 Point wiring for Two Way Controlled Light Point with 2-1.5 sq.mm & earth wire of 1.5 sq.mm Pt. 627.90 120.00

(green) both are of .ISI marked 1.1 KV grade ZHFR/ HRFR PVC insulated multi strand copper

wires erected in below type of pipe with 6A Modular type switches and following type of accessories

erected on PVC / Metallic/Wooden box, single mounting base frame covered with textured /

metallic/white front plate modules erected on / in wall / ceiling as per pipe erected. with necessary

batten/angle holder or ceiling rose or H.D.Connector as directed.

(f) with medium class Rigid PVC pipe and accessories erected concealed in wall/ceiling

complete(cat III)

NOTE:1. For use of ZHFR/HRFR Copper wires in place of FRLS PVC wires add 5% in Item of

Point wiring Item No 1-1-1 to 1-2-6 & 1-5-1 & 1-5-2.

7.9 Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper Rmt. 62.00 1,050.00

conductor wire in following type of pipe to be erected concealed in /flushed on wall/ceiling, with

sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of

(A) With medium class Rigid PVC pipe and accessories

(a) 2 wire 1.5 sq. mm

7.10 Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper Rmt. 82.00 50.00

conductor wire in following type of pipe to be erected concealed in /flushed on wall/ceiling, with

sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of

(A) With medium class Rigid PVC pipe and accessories

(b) 2 wire 2.5 sq. mm

Item no. Description Unit Rate Total Qty. Amount

7.11 providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper Rmt. 111.00 50.00

conductor wire in following type of pipe to be erected in / on wall / ceiling with 2.5 sq. mm copper

conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size

(A) with medium class Rigid PVC pipe and accessories

(a) 2 wire 4 sq. mm

7.12 providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper Rmt. 146.00 1,240.00

conductor wire in following type of pipe to be erected in / on wall / ceiling with 2.5 sq. mm copper

conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size

(A) with medium class Rigid PVC pipe and accessories

(b) 2 wire 6 sq. mm

7.13 providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper Rmt. 234.00 1,280.00

conductor wire in following type of pipe to be erected in / on wall / ceiling with 2.5 sq. mm copper

conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size

(A) with medium class Rigid PVC pipe and accessories

(c) 2 wire 10 sq. mm

(use earth wire of 4 sq.mm )

7.14 providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper Rmt. 258.00 810.00

conductor wire in following type of pipe to be erected in / on wall / ceiling with 2.5 sq. mm copper

conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size

(A) with medium class Rigid PVC pipe and accessories

(h) 4 wire 6 sq. mm

7.15 providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper Rmt. 421.00 140.00

conductor wire in following type of pipe to be erected in / on wall / ceiling with 2.5 sq. mm copper

conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size

(A) with medium class Rigid PVC pipe and accessories

(i) 4 wire 10 sq. mm

(use earth wire of 4 sq.mm )

7.16 Providing & erecting Switch board for Computer or electric apparatus consisting of following Pt. 1,122.00 35.00

modular type accessories mounted with PVC / Metallic concealed/open box with single mounting

base frame covered with textured/metallic /white front plate,modules erected with necessary

connections as directed

1 no. 6A/16A universal plug-switch combined.

3 nos. 6A Switch

3 nos. 6A 5 pin Plug

For Modular Type accessories Cat. III

Item no. Description Unit Rate Total Qty. Amount

7.17 SITC of following type of Modular Type accessories mounted with PVC / metallic/Wooden box, Ea. 395.00 380.00

single mounting base frame covered with textured / metallic/white front plate , modules erected

with necessary connections as per site situation directed by Engineer In charge.

(5) Electronic hum Free four or more steps EME Fan regulator (cat III)

7.18 providing and erecting Mains with ISI marked, 1.5KV grade electrolyte multi stranded, annealed Mtr. 298.00 100.00

copper conductor with heat resistant PVC insulated conforms to IS 694, IEC - 227 erected in

existing pipe of following size (Specifically for control panel, relays, power switchgears, motor

starters & control wiring) with required size of copper lugs, nuts and bolts if required.

(i) One wire 35.00 sq. mm

7.19 Providing following type of Modular Type Accessories mounted with PVC / metallic/Wooden box, Ea. 159.00 200.00

single mounting base frame covered with textured / metallic/white front plate , modules erected

with necessary connections as per site situation directed by Engineer In charge.

(4) TV Co-axial Socket outlet

7.20 SITC of following type of Modular Type accessories mounted with PVC / metallic/Wooden box, Ea. 25.00 25.00

single mounting base frame covered with textured / metallic/white front plate , modules erected

with necessary connections as per site situation directed by Engineer In charge.

(7) Blank Plate Single (cat III)

7.21 Providing and erecting ISI mark Medium class RIGID PVC PIPES of following size complete to be Ea. 33.00 100.00

erected on/in wall or ceiling erected with necessary PVC fittings & Junction boxes fixed with

adhesive solution & Clamps with following dia of pipes, in approved manner as directed

7.22 Providing and erecting ISI mark Medium class RIGID PVC PIPES of following size complete to be Ea. 54.00 100.00

erected on/in wall or ceiling erected with necessary PVC fittings & Junction boxes fixed with

adhesive solution & Clamps with following dia of pipes, in approved manner as directed

7.23 Providing and erecting ISI mark Medium class RIGID PVC PIPES of following size complete to be Ea. 67.00 50.00

erected on/in wall or ceiling erected with necessary PVC fittings & Junction boxes fixed with

adhesive solution & Clamps with following dia of pipes, in approved manner as directed

7.24 Batten Holder/Angle Holder with modular frame with metal ring. Ea. 64.00 740.00

Sub Total 7.....

8 INDOOR LIGHT FIXURE

8.1 Supply, Installation Testing and Commissioning of 20W CEILING/WALL MOUNTED TUBE Each 293.00 12.00

(A) Tube Light with integral driver

(iii) 18-20 Watts, Surge - 2KV,IP-20, conventional 4 feet

Item no. Description Unit Rate Total Qty. Amount

8.2 Supply, Installation Testing and Commissioning of 36W CEILING/WALL MOUNTED TUBE Each 530.00 80.00

(A) Tube Light with integral driver

(v) 36-40 Watts, Surge-2 KV, IP-20, conventional 4 feet

8.3 Supply, Installation Testing and Commissioning of 10W WALL MOUNTED MIRROR LIGHT Each 309.00 12.00

(H) Mirror Light 9 Watts, wall mounted minimum 1 feet long

8.4 Supply, Installation Testing and Commissioning of 24W CEILING SURFACE MOUNTED Each 751.00 940.00

(A) Square/ Circular shaped Surface/Recessed Mount Downlight with provision for spring loaded

mounting clips complete.IP20

(iv) 22-24 watts, Surge-2 KV

8.5 Supply, Installation Testing and Commissioning of 24W CEILING RECESSED MOUNTED Each 751.00 115.00

(A) Square/ Circular shaped Surface/Recessed Mount Downlight with provision for spring loaded

mounting clips complete.IP20

(iv) 22-24 watts, Surge-2 KV

8.6 Supply, Installation Testing and Commissioning of 18W CEILING SURFACE MOUNTED Each 584.00 120.00

(A) Square/ Circular shaped Surface/Recessed Mount Downlight with provision for spring loaded

mounting clips complete.IP20

(iii) 16-20 watts, Surge-2 KV

8.7 Supply, Installation Testing and Commissioning of 18W CEILING RECESSED MOUNTED Each 584.00 25.00

(A) Square/ Circular shaped Surface/Recessed Mount Downlight with provision for spring loaded

mounting clips complete.IP20

(iii) 16-20 watts, Surge-2 KV

8.8 Supply, Installation Testing and Commissioning of 10W CEILING SURFACE MOUNTED Each 423.00 25.00

(A) Square/ Circular shaped Surface/Recessed Mount Downlight with provision for spring loaded

mounting clips complete.IP20

(ii) 11-15 watts, Surge-2 KV

8.9 Supply, Installation Testing and Commissioning of 10W CEILING RECESSED MOUNTED Each 423.00 30.00

(A) Square/ Circular shaped Surface/Recessed Mount Downlight with provision for spring loaded

mounting clips complete.IP20

(ii) 11-15 watts, Surge-2 KV

8.10 Supply, Installation Testing and Commissioning of Flood Light: Each 9,552.00 16.00

(B) Flood Light (IP-65), Surge protection -4KV integral and ,Light must have 440VAC line supply

with over-voltage protection.

(vi) above 160 to 200 watts

Item no. Description Unit Rate Total Qty. Amount

8.11 Ceiling Fan: Each 1,929.00 380.00

Providing & erecting Approved make Power Saving 50 Watt Ceiling Fan with double ball bearing

ISI mark with Condenser 230 volt A.C. 50 Hz 1200 mm sweep complete having 3blades with

aluminium blades with , canopy & 30 cm. down rod erected with earthing.(Make shall be approved

by Engineer in charge))

8.12 SITC of approved make low noise decorative exhaust fan having size 200mm with 1350 RPM with Each 1,687.00 290.00

square frame.ABS body with inbuilt lowers & square frame.

8.13 SITC of suitable M.S. louver shutter of the Exhaust fan. Each 365.00 290.00

8.14 Wall bracket fan: Each 2,509.00 2.00

Supplying and erecting approved make oscillating type bracket fan A.C. 23OV. 50cy/s 400/450

mm sweep wall mounted with height adjustment and rotary tilting device complete with guard,

flexible Core plug top complete erected with lead wires as directed.

Sub Total 8.....

9.1 SITC of required size HOT deep Galvanised iron strip for earthing of H.T. , OCB/ ACB/ Kg. 77.00 1,115.00

Transformer LT panel board, Motors etc. using proper clamp.

9.2 SITC of required size Copper strip for earthing of H.T. OCB / ACB/ Transformer, LT panel board, Kg. 787.00 180.00

Motors etc. using copper clamp.

9.3 SITC of Annealed bare Copper wire 8 to 16 SWG. Kg. 787.00 100.00

9.4 SITC of HOT deep Galvanised iron strip wire 8 to 16 SWG. Kg. 77.00 15.00

9.5 Supplying & erecting earth pit of minimum bore dia.150mm size approved make Earthing Electrode Each 8,551.00 55.00

consisting Pipe-in-Pipe Technology as per IS 3043-1987 made of corrosion free hot dipped