Setting Up of Virology Laboratory at Soban Singh Jeena Govt. Institute of Medical Science and Research, Almorah in Uttarakhand on Turnkey Basis

Amount

Civil Work

DISMANTLING

Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material with in 50 meters lead as directed by Engineer-in-charge.

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : Of area 3 sq. metres and below

Dismantling Tile Flooring and Walls & Roof and disposing the debris away from site all complete as directed.Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.For thickness of tiles 10 mm to 25 mm

MASONRY WORK

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:4 (1 cement : 4 coarse sand)

PLASTERING

Prepare surfaces and plaster with CM 1:3 (1 cement: 3 fine sand) ,12mm minimum thick to all interior faces of walls (sponge finish) including RCC surfaces not contiguous to masonry.Necessary internal grooves of size 10mmx10mm shall be carried out as shown/directed by engineer-in-charge.

PAINTING

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Finishing with Deluxe Multi surface paint system for interiors using Primer as per manufacturers specifications : Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr /10 sqm

Aluminum Work

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :For Fixed Portion , Powder coated aluminium (minimum thickness of powder coating 50 micron) including rubber beedings in doors, windows and fixed portions.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free,straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/ sqm)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. Pre-laminated particle board with decorative lamination on both sides

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters & frames for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick Veneered flat pressed three layer or graded wood particle board with commercial veneering on both sides conforming to IS:3097, grade I

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge

Providing and fixing panelling or Providing and fixing panelled or Making Shelf, Racks, Tables, etc (Area of opening for panel excluding portion inside grooves or rebates to be measured): Marine Ply wood , 18 mm thick

Providing and fixing special quality chromium plated brass cupboard locks with six levers of approved quality including necessary screws etc. complete. Size 50 mm.

Providing and fixing magnetic catcher of approved quality in cupboard /ward robe shutters, including fixing with necessary screws etc. complete. Triple strip vertical type.

Providing and fixing special quality chromium plated brass cupboard locks with six levers of approved quality including necessary screws etc. complete. Size 50 mm.

Providing and fixing powder coated telescopic drawer channels(pair) 300 mm long with necessary screws etc. complete as per directions of Engineerin-charge.

Providing and fixing aluminium tubular handle bar 32 mm outer dia, 3.0 mm thick & 2100 mm long with SS screws etc .complete as per direction of Engineer-in-Charge.Polyester powder coated minimum thickness 50 micron aluminium tubular handle bar

Providing and fixing aluminium round shape handle of outer dia 100 mm with SS screws etc. complete as per direction of Engineer-inchargePowder coated minimum thickness 50 micron aluminium.

Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc. complete. With twin rubber stopper

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : 150x10 mm

Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.

Cladding & Partitions

Providing and fixing 50mm thick Double skin modular wall panels made of 0.5mm EGP Sheet. The density of PUF shall be 40±2kg/m³ as infill, GI profiles for reinforcement along the periphery, floor track in Painted GI with EPDM rubber below Floor Track using Fastener bolts, self-tapping screws at suitable interval, suitable to accommodate the epoxy/ PVC floor flush with wall panel. All panels should include a fifteen (15) year delaminating warranty. Wall paneling should be of DIN 410272 fire protection or Reaction to fire class 1 norm. Walls should provide X rays protection as required by AERB (Lead equivalent at 100 kV is 0.4mm) and have laser protection as per international standards. The Walls should be hermetically sealed. The system should afford the maximum versatility at the planning stage and flexibility during erection, ensuring openness to future alternations and trouble–free maintenance. During the installation of first the structural parts and subsequently the finishing elements, the system should ensure perfect integration of technical networks and allow ample operational flexibility on the construction site. The clean, dry installation method should enable optimum programming of the various work phases, allowing optimization of the installation of technical systems and any necessary alterations to be made – right up to checking and final testing of the installed systems – before the modules are sealed.The cavity between the inner and outer walls should be left with minimum obstructions for the possible addition of equipment at a later date and to enable services, pipes, conduits etc, to be run within the cavity. All joints and cavities should be filled with Metallic Epoxy sealer and sanded flush to provide seamless finish. The internal surfaces of the walls should be sprayed with water based liquid plastic (anti-bacterial paint) to a minimum dry film thickness of 300 microns with primer. The plastic coating should overlap the floor covering, ceiling system and door frames by 25 microns to provide a continuous sealed surface. The plastic coating should be non-reflective type, highly resistant to abrasives, water, detergents and weak acids and alkali used in cleaning area. The coatings should have no loss of performance or adhesion to the substrate in the case of regular steam cleaning. Anti bacterial paint applied should not leach out in order to maintain anti- microbial system throughout the life of the product. The coating should have biocide action and prevention property against growth of mould, bacteria and yeasts for at least 10 years. Including Panels, Frames, all material, lead lift T&P, Labour etc.

Providing and fixing 100mm thick Double skin modular wall panels made of 0.5mm EGP Sheet for Partitions. The density of PUF shall be 40±2kg/m³ as infill, GI profiles for reinforcement along the periphery, floor track in Painted GI with EPDM rubber below Floor Track using Fastener bolts, self-tapping screws at suitable interval, suitable to accommodate the epoxy/ PVC floor flush with wall panel. All panels should include a fifteen (15) year delaminating warranty. Wall paneling should be of DIN 410272 fire protection or Reaction to fire class 1 norm. Walls should provide X rays protection as required by AERB (Lead equivalent at 100 kV is 0.4mm) and have laser protection as per international standards. The Walls should be hermetically sealed. The system should afford the maximum versatility at the planning stage and flexibility during erection, ensuring openness to future alternations and trouble–free maintenance. During the installation of first the structural parts and subsequently the finishing elements, the system should ensure perfect integration of technical networks and allow ample operational flexibility on the construction site. The clean, dry installation method should enable optimum programming of the various work phases, allowing optimization of the installation of technical systems and any necessary alterations to be made – right up to checking and final testing of the installed systems – before the modules are sealed.The cavity between the inner and outer walls should be left with minimum obstructions for the possible addition of equipment at a later date and to enable services, pipes, conduits etc, to be run within the cavity. All joints and cavities should be filled with Metallic Epoxy sealer and sanded flush to provide seamless finish. The internal surfaces of the walls should be sprayed with water based liquid plastic (anti-bacterial paint) to a minimum dry film thickness of 300 microns with primer. The plastic coating should overlap the floor covering, ceiling system and door frames by 25 microns to provide a continuous sealed surface. The plastic coating should be non-reflective type, highly resistant to abrasives, water, detergents and weak acids and alkali used in cleaning area. The coatings should have no loss of performance or adhesion to the substrate in the case of regular steam cleaning. Anti bacterial paint applied should not leach out in order to maintain anti- microbial system throughout the life of the product. The coating should have biocide action and prevention property against growth of mould, bacteria and yeasts for at least 10 years. Including Panels, Frames, all material, lead lift T&P, Labour etc.

False Ceiling

Providing and fixing 50mm thick double skin panels made of 0.7 mm thick EGP Sheet. The density of PUF shall be 40±2kg/m³ as infill, GI profiles for reinforcement along the periphery. All panels should include a fifteen (15) year delaminating warranty. Wall paneling should be of DIN 410272 fire protection or Reaction to fire class 1 norm. Walls should provide X rays protection as required by AERB (Lead equivalent at 100 kV is 0.4mm) and have laser protection as per international standards. The Ceiling should be hermetically sealed. The system should afford the maximum versatility at the planning stage and flexibility during erection, ensuring openness to future alternations and trouble–free maintenance. During the installation of first the structural parts and subsequently the finishing elements, the system should ensure perfect integration of technical networks and allow ample operational flexibility on the construction site. The clean, dry installation method should enable optimum programming of the various work phases, allowing optimization of the installation of technical systems and any necessary alterations to be made – right up to checking and final testing of the installed systems – before the modules are sealed. All joints and cavities should be filled with Metallic Epoxy sealer and sanded flush to provide seamless finish. The internal surfaces of the Ceiling should be sprayed with water based liquid plastic (anti-bacterial paint) to a minimum dry film thickness of 300 microns with primer. The plastic coating should overlap the floor covering, ceiling system and door frames by 25 microns to provide a continuous sealed surface. The plastic coating should be non-reflective type, highly resistant to abrasives, water, detergents and weak acids and alkali used in cleaning area. The coatings should have no loss of performance or adhesion to the substrate in the case of regular steam cleaning. Anti bacterial paint applied should not leach out in order to maintain anti- microbial system throughout the life of the product. The coating should have biocide action and prevention property against growth of mould, bacteria and yeasts for at least 10 years. Including Panels, Frames, all material, lead lift T&P, Labour etc.

Flooring

Providing and fixing 2 mm antistatic seamless conductive PVC Flooring for Clean room. The floor should be scratch resistant, fire resistant, chemical resistant, non-corrosive, slip resistant, smooth, anti fungi, antimicrobial impervious material conductive enough to dissipate static electricity but not conductive enough to endanger personnel from electric shock. The floor finish should pass over a concealed cove former and continue up the wall for 100mm. The floor should be provided flat to within a tolerance of ±3mm over any 3 meter area. Copper grounding strip (0.05 thick, 50 mm width) should be laid flat on the floor in the conductive adhesive and connect to copper wire of grounding. The connection from copper grid should be brought out uniformly at places to form equipotential grid. A self-leveling compound should be laid prior to lying of the floor finish. One earthing lead should be brought out of from every 150 Sq.ft. area and attaching it to main earthing strip/ground. Continuous roll should be used and all the joints should be welded by heat fusion process to get seamless floor. The joints in the flooring should be sealed by using a PVC welding bar of matching colour and hot air gun for fusion of welding bar with flooring to provide a continuous sealed surface, confirming the European/US standards. The sheets should be highly durable with resistance to shock, scratch proof and indentation. Corners should be uniformly curved. The conductive material should be uniformly impregnated as grains. The floor should be inert to body fluids, chemicals, detergents and disinfectants and it should not be affected by temperature variation within the OT. Colour should be uniform, pleasant and matching with ambience. The floor should have electrical resistance(Point to ground) within 2.5x10 to 2.5x106 Ohms as per NFPA-99/ DIN 51953/ATMF-150 B1 class of fire resistance. The floor should efficiently discharge electric charges upto 2 KV. The floor should not allow build up of electrical charge beyond 100 volts due to antistatic effect. It should fulfill product requirement s as per EN649. The corner should not be terminated sharply and concealed cove-former (Aluminum) should be used overlap to a height of approx.25mm and sealed perfectly and uniformly. Self-leveling compounds should be used for this purpose.

Automatic Hermetically Sealing Doors

Providing, Fixing, Supply, Installation, and Commissioning of Automatic Hermetically Sealing door, having high pressure laminate on both sides that could withstand high abrasion , vision panels (300x500mm) . High grade aluminium extrusion profile to carry any door weight (till size 2400mm in width X 2400mm in height) with deep indentations to ensure perfect hermetic sealing. The door leaf should have high quality synthetic rubber gasket with long life to ensure hermetic sealing to maintain pressure differential. Air tightness 99.99% at a pressure 100KPa (Test certificate for hermetic sealing with door frame should be provided with pre-despatch documents. The finished door on either side of the door should be perfectly level (maximum permissible difference +1mm). The door should provide X-Ray protection as per AERB regulation (Lead equivalent at 100 KV is 0.27mm). Powder coated galvanized sheet 1mm thick over the full length of track with sloping top and closing caps.Door core of 60mm thick built up with 4mm thick HPCL (High Pressure Compact Laminate) skin at both side of the door to provide better strength and rigidity.CFC-free, high density polyurethane puff (density 40 kg/m3), thickness 52mm to provide better insulation.Door core is surrounded by 2.5 mm thick high grade aluminium extrusion profiles with natural anodizing of 15 microns finish. The aero- dynamic design of profiles makes the door ROBUST in its segment league.Gaskets Door blade is made with 3-tier specially designed 3 side heavy duty replaceable EPDM gasket against wall frame.Bottom sealing with 2-tier heavy duty EPDM gasket to flush with finished floor.Stainless Steel 304 grade lever handle on both side of the door blade for smooth and easy door opening and closing.High Quality double glazed flush vision window of Wall Frame High grade Aluminium extrusion with natural anodized 15 micron finish wall frame profile. This wall frame profile is 3-sided blind fixed with cladding on wall cut-out section from inside and outside of the room. Including Labour, Transpotation, Conveyance etc. The door interlock and access control system shall be provided with combination of proximity card based, numerical key pad lock based and push button based system. The system shall be complete with access logic controllers, door electromagnets, proximity cards and card reader/s, numerical keypad locks, door release push buttons, emergency door release buttons, PC communicator, control and power wiring and cabling and other required accessories, hardware,and software. The access control system shall be powered through UPS supply for uninterrupted operation even during mains power failure. The door Electromagnetic Lock shall be suitable for installation on doors/frames. The electromagnetic lock and armature shall be constructed and designed to provide trouble free service. MAKE: METAFLEX/REBBONE/ALTOS

Scrub Station

Providing and Fixing 2 bay Surgical Scrub Sink made out of 304 Stainless Steel & seamless welded construction polished to a satin finish which is operated on sensors.Overall Size 1600mmL x 622mmW x 718mmH (63"L x 24.5"W x 28.25"H) Sink Size 1525mmL x 508mmW x 356mmH (60"L x 20"W x 14"H) 2Nos of elbow operated water tap and a Soap Dispensor holder. Welding Joints TIG welding with seamless curves Drain and grid Surface. Including the Cost of 35m UPVC IN & OUT Pipes MAKE: . MEDFLOW/BALAJI/ALTOS/MOV MAK

Pass Box

Providing and fixing Pass Box of Chamber dimension 610 mm x 610 mm x 610 mm The unit shall be complete with HEPA filters, blower, motor, door electromagnets, door interlock, UV Lamp with timer, necessary wiring, controls and all other accessories. etc. complete. The Pass Box doors shall be interlocked by providing suitable electromagnet, so that both the door cannot be opened simultaneously. The interlock shall provide visual indicator for door open/close conditions. The blower motor of Pass Box shall of suitable rating and shall be dynamically and statistically balanced. Magnehelic differential pressure gauge shall be provided to indicate the pass box chamber pressure. The pass box shall be provided with UV light with ON/OFF switch and shall be interlocked with the pass box doors

Efluent Decontamination Sysytem

Supplying erection commissioning and testing of Chemical Decontamination System for BSL-3 Laboratory effluent shall comprise of two nos. Effluent Collection tanks for 5KLD (1 Working +1 Standby), each of full required Capacity. The decontamination tanks shall be constructed in SS 304 (14 gauge). The drain line from BSL-3 Laboratory containment area shall be terminated to the effluent decontamination tanks. The effluent decontamination tanks shall be provided with motorized OPEN/CLOSE valves connected with liquid level sensor such that when one tank get filled up to full volume, the supply valve shall automatically close and the supply valve of the standby tank shall automatically open to allow collection of effluent. One number chemical storage tank in SS 304 (14 gauge) fitted with transfer pump and measuring device, piped and connected to both the decontamination tanks shall also be provided for introducing disinfectant chemical into the decontamination tanks. The system shall be complete with items: -Motorized valve connected with liquid level sensor through control panel - Disinfectant Chemical storage tank - Disinfectant Chemical dosing pump - Non return valves - Interconnecting piping including piping for chemical dosing - Pumps for discharging decontaminated effluent into sewer/drain (1W+1S) - Power and control cabling/wiring for pumps and motorized valves with control panel. Including all the works with accessories.

Electrical Works

Point wiring in PVC conduit with modular type switch. Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group C

A/C point

S/F 20A SPN MCB industrial socket outlet: Supplying and fixing 20 amps, 240 volts, SPN industrial type, socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 amps "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

FOR HVAC MAINS:

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/recessed steel/ PVC conduit as required. 4 X 10 sq.mm + 2 X 6 sq.mm Earth wire

Telephone wiring in existing conduit:

Supplying and drawing following pair 0.5 sq mm FR PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. 2 Pair

Modular type blanking plate:

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Modular boxes, bases & cover plate:

Supplying and fixing following size/modules, GI box along with modular base & cover plate for modular switches in recess etc as required. 3 module

Supplying and fixing following size/modules, GI box along with modular base & cover plate for modular switches in recess etc as required. 6 module

Supplying and fixing following size/modules, GI box along with modular base & cover plate for modular switches in recess etc as required. 8 module

Modular type switch/socket:

Supplying and fixing following modular switch/socket on the existing modular plate & switch box including connections but excluding modular plate etc as required. 5/6 Amps switch

Supplying and fixing following modular switch/socket on the existing modular plate & switch box including connections but excluding modular plate etc as required. 3 pin 5/6 Amp socket outlet

Supplying and fixing following modular switch/socket on the existing modular plate & switch box including connections but excluding modular plate etc as required. 15/16 Amps switch

Supplying and fixing following modular switch/socket on the existing modular plate & switch box including connections but excluding modular plate etc as required. 6pin 15/16 Amps (universal) socket outlet

Supplying and fixing following modular switch/socket on the existing modular plate & switch box including connections but excluding modular plate etc as required. Telephone socket outlet

S/F PVC conduit:

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.(ISI Make) - 20mm

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.(ISI Make) - 25mm

LAN CABLE

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required. 2 run of cable

Installation Testing & Commisioning

ITC Fluorescent fitting directly on surface: Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting/LED of all types, complete with all accessories and tube etc. directly on ceiling/ wall, including connection with 1.5 sq. mm FR PVC insulated, copper conductor, single core cable and earthing etc. as required.

ITC Ceiling fan: Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FR PVC insulated, copper conductor, single core cable etc. as required.

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

LAYING OF CABLES

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required. FROM EB Mains TO VDB 3.5 X 50 sq.mm

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required. FROM VDB TO PBD1,2. 3.5 x 25 sq.mm

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required. FROM VDB TO DB-3 4 x 16 sq.mm

END TERMINATION

Supply and making end termination with brass compression gland, earth clip and aluminium lugs for following size of PVC insulated and PVC sheathed/XLPE aluminium conductor cable fo 1.1KV grade as required. 3.5 X 185 sq.mm

Supply and making end termination with brass compression gland, earth clip and aluminium lugs for following size of PVC insulated and PVC sheathed/XLPE aluminium conductor cable fo 1.1KV grade as required. 3.5 X 50 sq.mm

Supply and making end termination with brass compression gland, earth clip and aluminium lugs for following size of PVC insulated and PVC sheathed/XLPE aluminium conductor cable fo 1.1KV grade as required. 3.5 X 25 sq.mm

Supply and making end termination with brass compression gland, earth clip and aluminium lugs for following size of PVC insulated and PVC sheathed/XLPE aluminium conductor cable fo 1.1KV grade as required. 4 x 16 sq.mm

S/F of Vertical Distribution Board

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A, tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer) as required. (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 8 way (4 + 24), Double door

S/F FP ISOLATOR

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 100 A

S/F of TPN MCB DB

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 4 way (4 + 12), Double door

S/F OF SP MCB

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. 6/32 A SP MCB

EARTHING

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. (but without charcoal/ coke and salt ) as required.

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

Supplying and fixing TP sheet steel enclosure on surface/ recess along with 16/25/32 A 415 V "C" curve TP MCB complete with connections, testing and commissioning etc. as required.

FIRE ALARM SYSTEM-ADDRESSABLE

Supplying, installation, testing & commissioning of smoke detector with builtin LED and mounting base complete with all connections etc. as required.

Supplying, installation, testing & commissioning of manual call boxes of MS construction in surface/recess with stainless steel chain & hammer assembly complete with glass and push button etc. as required.

Supplying, installation, testing & commissioning of response indicator on surface/recessed MS Box having two LED, metallic cover complete with all connections etc as required

Supplying, installation, testing & commisssioning of intelligent addressable programmable sounder complete as required.

Supplying, installation, testing & commissioning of fault isolator complete with base as required

Supplying, installation, testing & commissioning of intelligent addressable thermal detector with rate of rise cum fixed tempreature thermistor complete with base as required.

Supplying, installation, testing & commissioning of addressable fire control module complete as required.

Supplying, installation, testing & commissioning of intelligent addressable duct detector including suitable Photo detector complete with base as required.

Supplying, installation, testing & commissioning of addressable manual call point complete as required.

Supplying & laying of 2x1.5 sqmm fire survival armoured cable, 600/1000V rated with annealed copper conductor having glass mica fire barrier tape covered by an extruded layer of Cross Linkable Ethylene Propylene Rubber (EPR) insulation and LSZH inner bedding, steel wire armouring & LSZH outer sheath complete as required

PUBLIC ADDRESS SYSTEM

Supplying, installation, testing & commissioning of ceiling/wall mounted loud speaker, 3/1.5 Watt in ABS enclosure complete as required.

Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the existing surface / recessed steel conduit of following pairs, cores and size including connections and interconnections etc. as required. speaker cable Single pair, 2-core, 1.5 sqmm

Supplying and installing following size of perforated painted with powder coating M.S. cable trays Tee with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 100 mm width X 50 mm depth X 1.6 mm thickness

NDSR ITEMS

SITC of modular type 20W LED tube fitting sleek with decorative end cap, powder coated CRCA steel channel complete with all electrical accessories like electronic ballast, lamp holder, 20W LED lamp etc complete as required. (Philips / Wipro /HAVELLS)

CLEAN ROOM LUMINAIRES

Supply,installation, testing and commissioning of 600x600 mm square type cool white, pure white LED recess mounted fixture with Integrated Driver & Backlight Technology with a minimum system efficiency of 95 w/Lm, lux level>400, Standard CCT: 3000k* 4000 k & 6500k, high colour rendering CRI>80, IP 55 with high efficiency driver, minimum of 35000 hours working life and surge protection -4kv(light variant as decided by engineer in charge). Fittings shall be sealed type, capable to withshand chemical fumigation. Each module should be tested and QC approved by competent authority and same to be furnished before electrical engineer HLL Life Care Ltd before purchase or else any higher or equivalent versions/specification may be used without change in cost, only at the discretion of HLL/NHM Engineer at site or Electrical Engineer( HLL ) (Make: Philips/wipro/Bajaj/Havells)

Supply and installation of 600 mm X 600 mm square type white LED , recess mounted fixture, decorative Soft lite luminaire, powder coated CRCA housing complete with all electrical accessories etc complete with all mounting accessories like chain, anchor fastner etc as required. (Havells VENUS NEO HE 2x2 R18-42WLED840MODUGR<19). or else any higher or equivalent versions/specification may be used only at the discretion of HLL/NHM Engineer at site or Electrical Engineer( HLL ).

Supply and installation of 1200 mm sweep Ceiling fan, white colour, 5 star rated as per BEE complete with blades, down rod, shackle, canopy etc(Make Havells/bajaj/usha/V-guard/crompton)

Supply and installation EXHAUST FAN,SHUTTER TYPE white colour, 9" OR 10" star rated as per BEE complete with its all accessories(Make Havells/bajaj/usha/V-guard)

EPABX SYSTEM

Supply, installation, testing and commissioning of EPABX System for upto 2 incoming lines and 8 outgoing lines[including connection for clean room phones] of ISI make complete with its all accessories

Supply and fixing of flush mounted Clean room telehone set for handsfree operation along with its telephone cabling works complete with its all accessories. The phone should have following capabilities 1. smooth front panel sealed with an overlay to keep the phone particulate-free and makes cleaning quick and easy. 2.Auto answer option allows clean room personnel to answer calls without leaving their stations. 3.Oversized buttons allow easy operation for gloved hands. Button function is clearly indicated. 6.Two auto-dial push buttons. 7.on/off push button with keypad for standard telephone operation.

Supply and fixing of Basic landline phone set with jumbo display complete with its all accessories.

FIRE ALARM SYSTEM

Supply, installation, testing and commissioning of 2 loop microprossesor based intelligent and electronically addressable , modular, loop capacity of 159 detectors . Fire alarm control panel with 5.7 inch touch screen LCD display , multiple access levels , 10,000 event history logs in the non volatile memory (EEPROM). The panel should be modular microprocessor based in nature. The panel shall have 240 V AC power supply, automatic battery charger, 24 v , ceiled lead acid maintanance free batteries sufficient for 24 hours normal working and then be capable of operating the system for 30mints during emergency condition. The panel shall be EN 54 /UL certification.

Beam Detector: Providing and fixing of Beam detector including mounting base along with interface module to direct connect to loop , having a coverage area with a distance of min 10m and maximum 100m with extra width up to 14 m , operating temperature range of -20C to +55C , Response sensitivity of 40%

Supply & Fixing ISI marked ( IS : 15683 ) Portable Fire Exitnguisher, ABC type,finished externally with red enamel paint, complete in all respects including initial fill and wall suspension of following capacity.-4 KG

Supply and installation of Co2 Fire Extinguisher (Trolley Mount - Wheel Operating) Type 4.5KG with MS clamps etc. for fixing on wall/wooden partition with 01 year warranty. I.S. No. 13849.

PUBLIC ADDRESS SYSTEM

Mixer amplifier: Supply Installation Testing & Commissioning of Class-D PA Amplifier with USB/SD, FM & Bluetooth with remote controller, RMS power: 35W, Impedence: 4Ω, 8Ω, 16Ω , Speaker output: 100V or 70V, Input: 3x Mic in, 2x Line in

Gooseneck Mic: Supply Installation Testing & Commissioning of 18" Condenser type Gooseneck mic with Frequency response: 30Hz-20kHz, Output impedance: 75Ω, Dynamic range: 109 dB, Signal to noise ratio: 65 dB, On/Off switch

LAN CONNECTION

Wall Mount Rack - 9U-Wall Mount Racks are made with solid steel structure 9U 19",with minimum dimensions 350x350x550 mm,(H x W x D), in a single section with front lockable glass door and with provision of two side cable entry from top and bottom with proper internal cable management and heat management. Having IP20 level protection.RAL 7035 SHADE , neatly finished etc as required

Supply and fixing RJ45 Keystone IO jack with cover and face plate, including crimbing/Punching of UTP 4 Pair CAT 6E LAN Cables on both ends with RJ45 Connector.

CABLE SUPPLY

Supply & laying of one number PVC insulated and PVC sheathed armoured aluminium power cable of 1.1KV grade of the following sizes in ground including excavation of trench of size 35 x 75 cm, refilling the trench etc. as required but excluding sand cushioning and protective covering (in ordinary soil).(Make:Havells/ Glostar/Nicco/Finolex/Polycab) FROM MSB TO SSB 3.5 core 185 sq mm

Supplying the following PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade as per CPWD standards as required. (Make:Havells/ Glostar/Nicco/Finolex/Polycab) 3.5 x 50 sq.mm

Supplying the following PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade as per CPWD standards as required. (Make:Havells/ Glostar/Nicco/Finolex/Polycab) 3.5 x 50 sq.mm

Supplying the following PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade as per CPWD standards as required. (Make:Havells/ Glostar/Nicco/Finolex/Polycab) 3.5 x 50 sq.mm

S/F of TPN MCB DB

Supplying and fixing following way, three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/recess, complete with tinned copper bus bar, neutral busbar, earth bar, din bar, detachable gland plate, interconnections, phosphatised and powder painted including earthing etc. as required (But without MCB/ RCBO/isolator) (Make: Legrand/Havells/HPL 12 way Double door, horizontal type

S/F of TP MCB

Supplying and fixing 6 amps to 63 amps rating, 415 Volts, "C" series, miniature cirucuit breaker suitable for lighting and other loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc as required.(Make: Legrand/Havells/HPL) 63A TP MCB

Supplying and fixing 6 amps to 63 amps rating, 415 Volts, "C" series, miniature cirucuit breaker suitable for lighting and other loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc as required.(Make: Legrand/Havells/HPL) 40A TP MCB

S/F of TPN RCBO

Supplying and fixing following rating, four pole, (three phase and neutral) 415 volts RCBO, having a sensitivity current upto 100/300 milliamperes in the existing MCB PDB complete with connections, testing and commissioning etc. as required.(Make: Legrand/Havells/HPL) 63 A 4P RCBO 100mA

Supplying and fixing following rating, four pole, (three phase and neutral) 415 volts RCBO, having a sensitivity current upto 100/300 milliamperes in the existing MCB PDB complete with connections, testing and commissioning etc. as required.(Make: Legrand/Havells/HPL) 40 A 4P RCBO 30mA

S/F FP MCCB in Exisiting VDB

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required. 150 A, 16 KA,TPMCCB

EARTHING WIRE

Supplying and laying 10 SWG Copper wire on, surface or in recess for loop earthing along with existing surface/recessed conduit/submain wiring/ cable as required.

SITC SPLIT AC

Supply, installation, testing and commissioning of 2 TR, 3 star rated (as per BEE) Air Cooled High Wall mounted Inverter type Split Air Conditioner consisting of high wall mounted type room unit (fan coil) with cordless remote control and one number outdoor condensing unit comprising of enegy efficient suitable rotary compressor for operation on single phase, 230 V, 50Hz supply, fixing the outdoor unit on a raised platform as per manufacturers recommendation and fixing of room (fan coil) unit on wall, standard 4 m distance refrigerant copper piping with 13mm nitrile rubber insulation, providing and making interconnection between room & condenser as per site conditions, comprising of 1" dia drain PVC pipe with insulation 4m, canvas connections, full electrical cabling from power plug near indoor unit and to outdoor unit, ODU MS stand, first charge refrigerant gas, suitable stabilizer etc complete as required. Make: Voltas, Toshiba, Blue Star, Siemens, Mitsubuishi, Hitachi or equivalent or as per the approval of Engineer in Charge

PANEL BOARD(SSB)

"Fabrication, supply, conveyance, installation testing and commissioning of floor or wall mounting, dust and vermin proof, cubicle type MV panel board comprising of the following components/ devices & complying to IS 8623. Fabrication of fully partitioned, dust and vermin proof enclosure for panel assembly as per form 4 of IS 8623 (with latest amendments) using CRCA sheet as per approved design and requirement, with front and rear access facility, bus bar chambers, hinged doors for all switch gear compartments, earthing the doors using 4 sq mm braided copper conductor, providing necessary cut-outs for mounting meters, relays, indication lamps, bus bar interconnection etc, detachable covers for bus bar chamber and cable alley, powder coating the assembly after subjecting to 7 tank process etc as required. CRCA sheet alone be used for the fabrication. Angles/ flats/ slotted angles etc shall not be used for the fabrication of panel assembly. The measurments will be taken the area of the complete sheets used for panel board including partitions, folding, shrouding etc. Supply and fabrication of MV panel board using 1.6mm CRCA sheet, powder coated (excluding base frame) " Incomer 400A, 35 Ka TPN MCCB -1No. 500A 415V best conductivity Al TPN bus bar with SMC supports, heat shrinkable sleeves etc complete as required. Digital ammeters with range 0-400A - 3 nos. CTs- ratio 400/5A 15VA CL-.2S -3 Nos. Three phase Digital Voltmeter range 0-500 V - 1 no. RYB phase indicating LED lamps with 2A SP MCB & switch- 1 set. Outgoings All MCCBs are to be with rotary operating handle and door interlock, spreader links, terminal shroud kit, phase barrier kit etc. 200A,25kA TPN MCCB with adjustable setting range - 2 no. 125A,25kA TPN MCCB with adjustable setting range - 2 no. 100A,25kA TPN MCCB with adjustable setting range - 1 no. Providing and Fixing of Electrical ISI Grade Rubber Mat suitable for 440Volts Switchboards. (6' x 3' x 1/4")

Provide and Fixing of L.T./H.T danger sign boards

PLC CONTROL SYSTEM

Fabricate, testing, supply and commissioning of Programmable logic control based control system for real time centrallized control & monitoring with all accessories, auxilliaries and associated equipments and cables for safe , efficient and reliable operation. The Control system shall include on-line self-surveillance, monitoring and diagnostic facility giving the details of the fault on the Human Machine Interface System (HMIS) viz. main & standby power supplies, sensor fault, Input/ Output card failure, Memory Status, Controller fault, failure of Communication/ Network links to PLCs, LAN. These faults shall be reported as colour change on system status display and as messages on HMIS as well as through local indication on the faulty module and on respective rack/ cubicle. The diagnostic system shall ensure that the faults are detected before any significant change in any controller output has taken place. PLC basaed system should includes: PLC modules(As per Annexure-1)

Fabricate, testing, supply and commissioning of Programmable logic control based control system for real time centrallized control & monitoring with all accessories, auxilliaries and associated equipments and cables for safe , efficient and reliable operation. The Control system shall include on-line self-surveillance, monitoring and diagnostic facility giving the details of the fault on the Human Machine Interface System (HMIS) viz. main & standby power supplies, sensor fault, Input/ Output card failure, Memory Status, Controller fault, failure of Communication/ Network links to PLCs, LAN. These faults shall be reported as colour change on system status display and as messages on HMIS as well as through local indication on the faulty module and on respective rack/ cubicle. The diagnostic system shall ensure that the faults are detected before any significant change in any controller output has taken place. PLC basaed system should includes: PLC modules(As per Annexure-2)

Fabricate, testing, supply and commissioning of Programmable logic control based control system for real time centrallized control & monitoring with all accessories, auxilliaries and associated equipments and cables for safe , efficient and reliable operation. The Control system shall include on-line self-surveillance, monitoring and diagnostic facility giving the details of the fault on the Human Machine Interface System (HMIS) viz. main & standby power supplies, sensor fault, Input/ Output card failure, Memory Status, Controller fault, failure of Communication/ Network links to PLCs, LAN. These faults shall be reported as colour change on system status display and as messages on HMIS as well as through local indication on the faulty module and on respective rack/ cubicle. The diagnostic system shall ensure that the faults are detected before any significant change in any controller output has taken place. PLC basaed system should includes: Door access system (As per Annexure-4)

Fabricate, testing, supply and commissioning of Programmable logic control based control system for real time centrallized control & monitoring with all accessories, auxilliaries and associated equipments and cables for safe , efficient and reliable operation. The Control system shall include on-line self-surveillance, monitoring and diagnostic facility giving the details of the fault on the Human Machine Interface System (HMIS) viz. main & standby power supplies, sensor fault, Input/ Output card failure, Memory Status, Controller fault, failure of Communication/ Network links to PLCs, LAN. These faults shall be reported as colour change on system status display and as messages on HMIS as well as through local indication on the faulty module and on respective rack/ cubicle. The diagnostic system shall ensure that the faults are detected before any significant change in any controller output has taken place. PLC basaed system should includes: Control panel(As per Annexure-3)

Fabricate, testing, supply and commissioning of Programmable logic control based control system for real time centrallized control & monitoring with all accessories, auxilliaries and associated equipments and cables for safe , efficient and reliable operation. The Control system shall include on-line self-surveillance, monitoring and diagnostic facility giving the details of the fault on the Human Machine Interface System (HMIS) viz. main & standby power supplies, sensor fault, Input/ Output card failure, Memory Status, Controller fault, failure of Communication/ Network links to PLCs, LAN. These faults shall be reported as colour change on system status display and as messages on HMIS as well as through local indication on the faulty module and on respective rack/ cubicle. The diagnostic system shall ensure that the faults are detected before any significant change in any controller output has taken place. PLC basaed system should includes: CCTV System.(As per Annexure-5)

Fabricate, testing, supply and commissioning of Programmable logic control based control system for real time centrallized control & monitoring with all accessories, auxilliaries and associated equipments and cables for safe , efficient and reliable operation. The Control system shall include on-line self-surveillance, monitoring and diagnostic facility giving the details of the fault on the Human Machine Interface System (HMIS) viz. main & standby power supplies, sensor fault, Input/ Output card failure, Memory Status, Controller fault, failure of Communication/ Network links to PLCs, LAN. These faults shall be reported as colour change on system status display and as messages on HMIS as well as through local indication on the faulty module and on respective rack/ cubicle. The diagnostic system shall ensure that the faults are detected before any significant change in any controller output has taken place. PLC basaed system should includes: Computer (As per Annexure-6)

Fabricate, testing, supply and commissioning of Programmable logic control based control system for real time centrallized control & monitoring with all accessories, auxilliaries and associated equipments and cables for safe , efficient and reliable operation. The Control system shall include on-line self-surveillance, monitoring and diagnostic facility giving the details of the fault on the Human Machine Interface System (HMIS) viz. main & standby power supplies, sensor fault, Input/ Output card failure, Memory Status, Controller fault, failure of Communication/ Network links to PLCs, LAN. These faults shall be reported as colour change on system status display and as messages on HMIS as well as through local indication on the faulty module and on respective rack/ cubicle. The diagnostic system shall ensure that the faults are detected before any significant change in any controller output has taken place. PLC basaed system should includes: Actuator (As per Annexure-7)

BAG-IN-BAG-OUT

Supply, installation, testing and commissioning of Bag in Bag out[BIBO] unit complete with its all accessories. The unit should have the following specification listed as per annexure 8.

Supply and fixing of 2 KVA UPS (ONLINE) with battery backup for 15 minutes.( single phase 230V AC+ Neutral + Earth, 50 Hz, p.f of 0.9 output, pure sine wave output, Harmonic distortion: < 2% (linear load) / 5 % nonlinear load, efficiency 90%, Bypass: Static bypass Transfer time

DUCTABLE TYPE SPLIT AIR CONDITIONER - PART A

SITC of DX type double skinned air handling units, ceiling suspended/ floor mounting type 11TR, 750lps capacity complete with suitable DIDW blower (as per approved make), blower section, static presure of 150 mm of water column, built in pre filter, fine filter & hepa filter 99.97% effieciency down to 0.3 microns and controls connected to condensing units, insulated SS drain pan 6 row cooling coil, electric motor , direct driven package with TEFC motor class B insulation, suitable for 3 phase, 415V 50Hz supply, suitable AHU panel & cabling. AHU temp & speed control panel, ARI certified, with 0.70 mm sheet for outer skin and plain GP 0.63 mm sheet for inner skin 47mm thick PUF panel, belt guards, suitable supports for suspending from slab, vibration isolator, strip heater etc. conforming to specifications. Refer Annexure 9: 8.5 Tr (3600 cfm) with 3 stage Filteration

SITC of DX type double skinned air handling units, ceiling suspended/ floor mounting type 11TR, 750lps capacity complete with suitable DIDW blower (as per approved make), blower section, static presure of 150 mm of water column, built in pre filter, fine filter & hepa filter 99.97% effieciency down to 0.3 microns and controls connected to condensing units, insulated SS drain pan 6 row cooling coil, electric motor , direct driven package with TEFC motor class B insulation, suitable for 3 phase, 415V 50Hz supply, suitable AHU panel & cabling. AHU temp & speed control panel, ARI certified, with 0.70 mm sheet for outer skin and plain GP 0.63 mm sheet for inner skin 47mm thick PUF panel, belt guards, suitable supports for suspending from slab, vibration isolator, strip heater etc. conforming to specifications. Refer Annexure 9: 8.5 Tr (1900 cfm) with 3 stage Filteration

Supply, installation, testing and commissioning (SITC) of 8.5 TR capacity aircooled inveter type Outdoor condensing unit with single/multi scroll compressor as per specifications complete with suitable capacity drive motor, air cooled condenser with all accessories, hermetically sealed scroll compressor, electronic microprocessor pendant controller with digital display, first charge R 407A/R410A refrigerant gas, vibration isolator pads and saftey devices like thermal protector, pressure relief valve, over load relays single phase preventor, high-low pressure cut out, suitable for three phase 440V supply.

Supply, installation, testing and commissioning of suitable sized hard drawn copper refrigerant piping(both suction and liquid piping) including 25mm thick dosed cell elastomeric insulation as per specification for 11 TR machine between indoor & outdoor units as per site conditions complete in all respect.

Supply, installation, testing and commissioning SS drain pipe of suitable dia connecting to the ss drain pan of the indoor units to nearest drain point, with 12mm thick dosed cell elastomeric insulation as per specification

Canvass connection out of synthetic SRF cloth with zip fastener for measuring temperature at the outlet of AHU.

Supply and fixing of Underdeck insulation with 13 mm thick Fire retardent class nitrile rubber stuck with synthetic adhesive and held in position with SS screw and washer at 600mm centres and cross braced with SS 20SWG wire netting

Supply , installation, Testing and Commissioning of thick extruded aluminum profiles frame and sealed gasketed Laminar Air flow system with plenum for air distribution complete with 6 Nos. HEPA Filters ( usage for seperate roonwise) efficiency 99.99% down to 0.3 microns ) with uv sterilization complete.For Distribution of supply/ return air flow. Designs of class 100. (< = 100 particles/ft3) and bacteriological class B ( = 5 cfu/m3). Hepa should be capable to withstand corrosive agents and gases and have the following items: a.Protective grids : White epoxy painted micro drawn grid b.Separators : Continuous thermo plastic chord c.Sealant : Polyurethane . d.Gasket : One piece polyurethane e.EN 1822 class : H14 f.MPPS average efficiency: > 99.995% g.3 Micron DOP efficiency > 99.999% h.Pressure drop : 600 pa(max) i.Maximum Operating Temp : 60 degree Celsius j.Maximum RH : 90 %. (Submission of test certificate for the filters from original manufacturer is must along with its supply).(Details specifiec in Annexure:10)

Supply, installation and testing of Exhaust fan/blowers with hepa filtered for uni directional air circulation-As per Annexure 11) Exhaust Fan location for BSL-3 : Minimum 25 ft from AHU intake Air velocity at exhaust discharge : 15-20 m/s (3000-4000 fpm) for BSL-3

PRESSURE RELIEF DAMPER

Providing, Fixing, Supply and Installation and Commissioning of proper Pressure Relief Dampers having multi 304 graded stainless steel blades for maintaining the negative pressure inside the lab.

PART B - FILTERATION FOR ICU STANDARDS

Supply, installation, testing and balancing of Powder coated/Anodised extruded aluminium construction, inlet air louvers with bird screen, volume damper & filter for fresh air as per specifications and approved drawings.

FILTERS: F-7 Filter & Discharge supply section ,Flanged type F-7( 3 micron) Fine filter Flanged type G-4 Pre-filters of capacity-1 no spare.

Lowside Ancillary Works Part C

Supply, installation, balancing and commissioning of ISI-655 site fabricated 22 swg 304 Grade SS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specificatio

Supply, installation, balancing and commissioning of ISI-655 site fabricated make 22 swg 19mm insulation of class O, aluminium sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications.

Supply, installation, testing and commissioning of centrifugal stainless steel air curtain with remote and sensor with high quality international standards - CE GS Approved Casing made in Stainless Steel body which is sealed to resist dust going inside, with fire and corrosion resistance, and easy for cleaning and maintenance. Blowers are made of high quality ABS to ensure less noise with toughness intensified High quality motor, low noise, overload protection, and long life-span. Air speed is with High and Low two switch of speeds

Supply, installation, testing and commissioning of 2" Air tight valves for isolating the air circulation from the proposed facility or laboratory room to become isolated from the rest of the HVAC system without affecting other areas

DUCT INSULATION / ACOUSTIC INSULATION

Supplying and fixing of following thickness duly laminated aluminum foil of mat finish closed cell Nitrile rubber (Class "O") insulation on existing duct after applying suitable adhesive for Nitrile rubber. The joints shall be sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape insulation complete as per specifications and as required. 19mm

Supplying and fixing of following thickness duly laminated aluminum foil of mat finish closed cell Nitrile rubber (Class "O") insulation on existing duct after applying suitable adhesive for Nitrile rubber. The joints shall be sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape insulation complete as per specifications and as required. 25mm

Supplying, fixing acoustic lining on wall and ceiling of AHU rooms with 50mm thick, density 32 kg/cu.m resin bonded glass fiber insulation friction fixed in 610mm x 610 mm frame work made of 25X50X50X50X25 mm made out of 0.6mm thick GI sheet U shaped channel and covered with reinforced fiber glass tissue and finished with 0.80 mm perforated aluminium sheet etc. complete as required and as per specifications.

AIR TERMINAL DEVICES

Supplying & fixing of powder coated extruded aluminium Supply Air Grills with aluminium volume control dampers as per specifications.

Supplying & fixing of powder coated extruded aluminium Return Air Grills with louvers but without volume control dampers complete as required.

Supply, installation, testing & commissioning of thermal insulated flexible duct of following sizes duly supported at regular interval as per site requirement etc. complete as required as per specifications, 200mm dia

Supplying, Fixing,testing and commissioning of fire dampers in supply air duct/main branch and return air path as and where required of required sizes i/c control wiring,the damper shall be motorized and spring return so as to close the damper in the event of power failure automatically and open the same in case of power being restored. The spring return action shall be inbuilt mechanism and not externally mounted. The damper shall also be closed in the event of fire signal complete as required and as per specifications. Fire Damper

Supplying, Fixing,testing and commissioning of fire dampers in supply air duct/main branch and return air path as and where required of required sizes i/c control wiring,the damper shall be motorized and spring return so as to close the damper in the event of power failure automatically and open the same in case of power being restored. The spring return action shall be inbuilt mechanism and not externally mounted. The damper shall also be closed in the event of fire signal complete as required and as per specifications. Actuator

Supply, installation, testing and commissioning of Motorized (ON-OFF Type) duct mounted GI volume control damper with enthalpy sensor and necessary control wire (minimum 1.5 sqmm) for integration within AHU room Damper

Supply, installation, testing and commissioning of Motorized (ON-OFF Type) duct mounted GI volume control damper with enthalpy sensor and necessary control wire (minimum 1.5 sqmm) for integration within AHU room Actuator

Supply & fixing of powder coated extruded aluminium SUPPLY AIR DIFFUSER with aluminium volume control dampers as per specification with anti smudge ring & removable core.

Supply & fixing of powder coated extruded aluminium RETURN AIR DIFFUSER with louvers without volume control dampers as per specification anti smudge ring & removable core.

Description of Work / Item(s)

Amount

Anaerobic Gas Jar

Antibiotic Zone Scale

Autoclave Vertical (79 L)

Beaker 10Ml

Beaker 1000Ml

Beaker 25ML

Beaker 250Ml

Beaker 50Ml

Beaker 500ML

BOD Incubator 170L

Computer With Printer

Conical Flask 1000ML

Conical Flask 100ML

Conical Flask 10ML

Conical Flask 250ML

Conical Flask 25ML

Conical Flask 500ML

Conical Flask 50ML

Cross Over Bench (Stainless Steel)

Dropping Bottle tbr Stains (125ML)

Elctronic Balance (Micro/Semi Micro)

Elisa Reader and Washer

Filtration apparatus for preparation of tissue/cell culture media

Flask flat Bottom (1000 ml)

Freezer -20C

Freezer -70C

Fumigation apparatus

Garment Shelf (Stainless Steel)

Heating Block

Hot Air Oven (Digitally Control)

Hygrometer

Ice-making machine

Incubator

Inverted Light Microscope

Laminar Air flow Cabinet

Liquid nitrogen containers

Magnetic Stirrer with Bead

Measuring Cylinder (10 ml)

Measuring Cylinder (100 ml)

Measuring Cylinder (1000 ml)

Measuring Cylinder (25 ml)

Measuring Cylinder (250 ml)

Measuring Cylinder (50 ml)

Measuring Cylinder (500 ml)

Micropipette Tips (variable Volume) 0-10 µl

Micropipette Tips (variable Volume) 0-200 µl

Micropipette Tips (variable Volume) 200-1000 µl

Micropipette Tips 0.1 - 10 µL

Micropipette Tips 0.5 -20 ul

Micropipette Tips 0.5-10ml

Microwave Oven

Mini Centrifuge (No spec.)

Multichannel Pipette-variable volume 0.1 -2.5µl, 0.5-10µl, 5- 50µl, 20-200µl, 10-100µl,

PCR Workstation

Petridish with lid 100x 15mm

Petridish with lid 100x17 mm

Petridish with lid 150x 25mm

Petridish with lid 200x 30mm

Petridish with lid 50x12 mm

Petridish with lid 50x17mm

Petridish with lid 80x 15mm

Petridish with lid 80x17mm

Petridish with lid 90x 15mm

pH Detern'rination apparatus (pH meter with digital display)

Pipette Graduated 1 ml

Pipette Graduated 10 ml

Pipette Graduated 2 ml

Pipette Graduated 25 ml

Pipette Graduated 5 ml

Pipette Sterilization Can

Plate Centrifuge (No Spec.)

Reagent Bottles/ Stopper - 100 cc

Reagent Bottles/ Stopper - 1000 cc

Reagent Bottles/ Stopper - 250 cc

Reagent Bottles/ Stopper - 50 cc

Refrigerated Centrifuge for Virology

Refrigerated centrifuge PCR

Refrigerator (300 ltr or More)

Single channel Pipette-variable volume 0.5-l0µl, 5-50µl, 50-200µl,200-1000 µl

Slides

Staining (troug) rod (10 slides)

Stool (Stainless Steel)

Table (Stainless Steel)

Test tube 75 x 12 mm

Test tube l00 x l2 mm

Test tube l50 x l8 mm

Thermometer

Ultra Sonic bath

Ultrapure Water Purifier

UPS (20 KVA)

UV Larnp

Volumetric Pipette 1 ml

Volumetric Pipette 10 ml

Volumetric Pipette 2 ml

Volumetric Pipette 20 ml

Volumetric Pipette 25 ml

Volumetric Pipette 5 ml

Voluntetric Flask 100 ml

Voluntetric Flask 1000 ml

Voluntetric Flask 250 ml

Voluntetric Flask 50 ml

Voluntetric Flask 500 ml

Vortex Mixer

Water bath

Description of Work / Item(s)

Amount

Autoclave Vericle (79L)

2nd Year

3rd Year

4th Year

5th Year

6th Year

BOD Incubator 170L

2nd Year

3rd Year

4th Year

5th Year

6th Year

Computer With Printer

2nd Year

3rd Year

4th Year

5th Year

6th Year

Elctronic Balance (Micro/Semi Micro)

2nd Year

3rd Year

4th Year

5th Year

6th Year

Elisa Reader and Washer

2nd Year

3rd Year

4th Year

5th Year

6th Year

Freezer -20C

2nd Year

3rd Year

4th Year

5th Year

6th Year

Freezer -70C

2nd Year

3rd Year

4th Year

5th Year

6th Year

Ice Making Machine

2nd Year

3rd Year

4th Year

5th Year

6th Year

Inverter Light Microscope

2nd Year

3rd Year

4th Year

5th Year

6th Year

Liquid Nitrogen Containers

2nd Year

3rd Year

4th Year

5th Year

6th Year

Mini Centrifuge

2nd Year

3rd Year

4th Year

5th Year

6th Year

PCR Workstation

2nd Year

3rd Year

4th Year

5th Year

6th Year

Plate Centrifuge

2nd Year

3rd Year

4th Year

5th Year

6th Year

Refrigerated Centrifuge for Virology

2nd Year

3rd Year

4th Year

5th Year

6th Year

Refrigerated Centrifuge PCR

2nd Year

3rd Year

4th Year

5th Year

6th Year

Ultra Sonic Bath

2nd Year

3rd Year

4th Year

5th Year

6th Year

Ultrapure Water Purifier

2nd Year

3rd Year

4th Year

5th Year

6th Year

UPS (20 KVA)

2nd Year

3rd Year

4th Year

5th Year

6th Year

Genesys

Genesys

Genesys