Fire Safety System

Name of Work: Taluka Sevasadan at Dabhoi, Dist. Vadodara (Upgradation of Fire Hydrant

System and Implementation of Fire Sprinkler Systems with Conventional Alarm and Detection

System with Fire pump etc.)

BILL OF QUANTITIES

It. No. Description of Item Quantity Unit Rate in Figure Total

1 (A) Supplying, installation, testing and commissioning of Electric 1.00 Set 328966.95

Driven Main Fire Pump suitable for automatic operation and

consisting of following, complete in all respects, as required:

(B) Horizontal type, single Stage, centrifugal, End suction pump of

cast iron & bronze impeller with stainless steel shaft, Gland Pack

conforming to IS

(C) Suitable HP Squirrel cage induction motor, TEFC, synchronous

speed 2900 RPM, suitable for operation on 415 volts, 3 phase

Hz, AC supply with IP 55 protection for enclosure, horizontal foot

mounted type with Class-'F' insulation, conforming to JS-325.

(D) M.S. fabricated Common base plate, coupling, coupling guard,

foundation bolts etc. as required.

(E) Suitable cement concrete foundation duly plastered with anti

vibration pads.

2280 LPM at 88 m Head

2 (A) Supplying, installation, testing and commissioning of Diesel 1.00 Set 544162.71

Engine Driven Fire Pump suitable for automatic operation and

consisting of following, complete in all respects, as required:

(Diesel Driven Pump)

(B) Horizontal type, Single stage, centrifugal pump of cast of iron

body and bronze impeller with stainless steel shaft, mechanical

seal conforming to IS

(C) Suitable HP, 1500/2300 RPM water cooled with radiator, diesel

engine conforming to relevant IS standard

complete with auto starting mechanism, 12 /24 volts electric

starting equipment, 125 Ltrs diesel tank, exhaust pipe extended

upto 10 m outside pump house duly insulated with 50 mm thick

glass wool with 1.0 mm thick aluminium sheet cladding, residential

silencer, instruments and protection as per standard specification,

stop solenoid for auto stop in the event of fault with audio

indications, painted with post office red colour etc. as required.

(D) M.S fabricated, common base plate, coupling, coupling guard,

foundation bolts etc. as required.

(E) Suitable cement concrete foundation duly plastered and with

anti vibration pads.

2280 LPM at 88 m head

3 (A) Supplying, installation, testing and commissioning of Electric 1.00 Set 92588.14

Driven Pressurisation Pump suitable for automatic operation and

consisting of following, complete in all respects, as required:

(B) Horizontal type/Vertical Inline type, Single Stage/Multi Stage,

centrifugal End suction pump of cast iron body and bronze impeller

with stainless steel shaft, mechanical seal conforming to IS:

(C) Suitable HP squirrel cage induction motor TEFC type suitable

for operation on 415 volts, 3 phase 50 Hz AC supply with IP

class of protection for enclosure, horizontal foot mounted type with

Class-'F' insulation, conforming to IS:

(D) M.S. fabricated Common base plate, coupling, coupling guard,

foundation bolts etc. as required.

(E) Suitable cement concrete foundation duly plastered and with

anti vibration pads.

180 LPM at 88 m Head

It. No. Description of Item Quantity Unit Rate in Figure Total

4 Fabrication, Supply, Installation, testing & commissioning of 1.00 Set 254917.80

Electrical Control Panel of cubical construction, floor mounted type,

fabricated out of 2mm thick CRCA sheet, compartmentalised with

hinged lockable doors, dust and vermin proof, powder coated of

approved shade after 7 tank treatment process, cable alley, inter

connection with suitable size copper conductor cable/solid copper

strip, having switchgears and accessories, mountings and internal

wiring, earth terminals, numbering etc. complete in all respect,

suitable for main fire pump. pressurisation pump & diesel pump set

complete as per CPWD specification with following in coming and

Outgoings, suitable for operation on 415V, 3 phase, 50Hz AC

supply with enclosure protection class IP 42 as required: for all

suitable AMP fire pump and Disel Pump in one cubical construction

400A. 50kA 4 Pole MCCB, lcs=100% Icu rating

Digital Voltmeter 0-500 V with selector switch

Digital Ammeter (0-250A) with selector switch & CTs etc.

LED type RYB phase indicating lamps, ON, OFF, trip indicating

Set of Copper Bus Bar 300A

(Note: All outgoing feeders for pumps should have digital Ammeter

with selector switches, and LED type ON, OFF, trip indicating

125 A, 50kA TPN MCCB, lcs=l00% lcu, with fully automatic

Star/Delta starter suitable for 60 HP pump with overload protection,

current sensing type single phase preventor complete with all

accessories and internal wiring required for automatic operation,

selector switch for local/remote,auto / manual /OFF operation.

63 A, 50kA TPN MCCB, lcs=100% lcu, with suitable HP fully

automatic Star/Delta starter with overload protection, current

sensing type single phase preventor complete with all accessories

and internal wiring required for automatic operation, selector switch

for local/remote, auto / manual / OFF operation.

DIESEL ENGINE CONTROL

Control for diesel engine comprising -

Automatic/Manual selector switch & 3 attempts starting device,

timers and relays as required, push buttons, start/stop in manual

Indicating lamp for high/ Low Lub. Oil pressure, High Water Temp

and Engine on indication

Battery charger suitable for 12V/24 V DC with boost and trickle

selector switch, 0-30 V DC volt meter, and 0-20 A DC Ammeter.

All standard relays and accessories for automatic operation of

System Controller

Designing, Supply, Installation, Testing and commisioning of

system controller to control operation of main electric fire pump,

diesel pump, Pressurization pump, Terrace pump in sequence as

per specification consisting of relays, timers. Sensors, annunciation

window for fault indication, complete as per specification.

5 Providing, laying, testing & commissioning of 'B' class Medium duty 14.00 Mtr. 602.54

G.l. pipe conforming to IS 1239 including welding, fittings like

elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing

the pipe on the wall ceiling with painting with two or more coats of

synthetic enamel paint of required shade complete as required:

excluding the cost of Excavation, refilling, demolition of RCC work

and demolition of paver block. 25 mm

It. No. Description of Item Quantity Unit Rate in Figure Total

6 Providing, laying, testing & commissioning of 'B' class Medium duty 27.00 Mtr. 903.39

G.l. pipe conforming to IS 1239 including welding, fittings like

elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing

the pipe on the wall ceiling with painting with two or more coats of

synthetic enamel paint of required shade complete as required:

excluding the cost of Excavation, refilling, demolition of RCC work

and demolition of paver block. 50 mm

7 Providing, laying, testing & commissioning of 'B' class Medium duty 18.00 Mtr. 1127.12

G.l. pipe conforming to IS 1239 including welding, fittings like

elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing

the pipe on the wall ceiling with painting with two or more coats of

synthetic enamel paint of required shade complete as required:

excluding the cost of Excavation, refilling, demolition of RCC work

and demolition of paver block. 65 mm

8 Providing, laying, testing & commissioning of 'B' class Medium duty 9.00 Mtr. 1283.05

G.l. pipe conforming to IS 1239 including welding, fittings like

elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing

the pipe on the wall ceiling with painting with two or more coats of

synthetic enamel paint of required shade complete as required:

excluding the cost of Excavation, refilling, demolition of RCC work

and demolition of paver block. 80 mm

9 Providing, laying, testing & commissioning of 'B' class Medium duty 46.00 Mtr. 1631.36

G.l. pipe conforming to IS 1239 including welding, fittings like

elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing

the pipe on the wall ceiling with suitable clamp/support frame and

painting with two or more coats of synthetic enamel paint of

required shade complete as required: excluding the cost of

Excavation, refilling, demolition of RCC work and demolition of

paver block. 100 mm

10 Providing, laying, testing & commissioning of 'B' class Medium duty 94.00 Mtr. 2231.36

G.l. pipe conforming to IS 1239 including welding, fittings like

elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing

the pipe on the wall ceiling with suitable clamp/support frame and

painting with two or more coats of synthetic enamel paint of

required shade complete as required: excluding the cost of

Excavation, refilling, demolition of RCC work and demolition of

paver block. 150 mm

11 Supplying and fixing single headed internal/External hydrant valve 6.00 Each 6955.93

with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia

with cast iron wheel ISI marked conforming to IS 5290 (Type -A)

with blank Gunmetal/Stainless Steel cap and chain as required:

Single Headed Stainless Steel

12 Supplying & fixing 63 mm dia. Stainless Steel (Grade 304) short 9.00 Each 2883.05

branch pipe with 20 mm nominal internal diameter size nozzle

conforming , to IS:903 suitable for instantaneous connection to

interconnect hose pipe coupling as required: Stainless Steel

13 Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 18.00 Each 3955.08

mm dia male and female couplings duly bound with GI wire, rivets

etc. conforming to IS 636 (type-A) as required: Stainless Steel

14 Supplying and fixing first-aid Hose Reel Drum with MS construction 9.00 Each 8000.00

spray painted in post . office red, conforming to IS 884 complete

with the following as required. 20/25 mm nominal internal dia water

hose thermoplastic (Textile reinforced) type -2 as per IS: 12585

mm nominal internal dia gun metal globe valve & nozzle. Drum and

brackets for fixing the equipments on wall. Connections from riser

with 25 mm dia stop gun metal valve & M.S. Pipe and socket. 30 m

15 Supplying, fixing, testing and commissioning of butterfly valve of 1.00 Each 4581.36

PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete

with nuts, bolts, washers, gaskets conforming to IS: 13095 of

following sizes as required: 80 mm dia

It. No. Description of Item Quantity Unit Rate in Figure Total

16 Supplying, fixing, testing and commissioning of butterfly valve of 6.00 Each 6161.86

PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete

with nuts, bolts, washers, gaskets conforming to IS: 13095 of

following sizes as required: 100 mm dia

17 Supplying, fixing, testing and commissioning of butterfly valve of 3.00 Each 8251.69

PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete

with nuts, bolts, washers, gaskets conforming to IS: 13095 of

following sizes as required: 150 mm dia

18 Providing, installation, testing and commissioning of non-return 1.00 Each 6995.76

valve of following sizes confirming to IS: 5312 complete with rubber

gasket, GI bolts, nuts, washers etc.as required: 80 mm dia.

19 Supplying installing testing & commissioning of 100 mm dia. 2.00 Each 1783.94

Pressure gauge 1% Accuracy direct bottom 3/8" BSP connection in

brass socket & Range 0 to 16 Kg/Cm2 etc. necessary as directed

by Engineer in Charge.

20 Providing and Fixing pressure switch in M.S. Pipe line including 2.00 Each 1415.25

connection etc. as required.

21 Providing and Installation SS 304 male to male siphone tube size 2.00 Each 1150.03

3/8 inch dia for pressure gauge.

22 Providing and Installation SS 304 male to male siphone tube size 2.00 Each 1150.03

1/4 inch dia for pressure switch.

23 Providing and Fixing 25 mm dia. Air valve of Raising Main Line. For 4.00 Each 970.73

Air Release including supply, installing, testing and commissioning

etc. complete as directed by Engineer in charge.

24 Supplying, Installing, Testing & Commissioning of following dia. 2.00 Each 16059.00

Foot Valve with gasket, Nu-bolts etc. necessary complete as

directed by engineer in charge. 150mm dia.

25 Supplying, Installing, Testing & Commissioning of following dia. 1.00 Each 12928.00

Foot Valve with gasket, Nu-bolts etc. necessary complete as

directed by engineer in charge. 100mm dia.

26 Supplying and fixing of fire brigade connection of cast iron body 1.00 Each 6154.24

with gun metal male instantaneous inlet couplings complete with

cap and chain as reqd. for suitable dia MS pipe connection

conforming to IS 904 as required: 2 way

27 Steel work, welded in built up sections framed work including 50.00 Kg. 91.08

cutting, hoisting, fixing in position and applying a priming coat of

red lead paint. (A) In neams and joints, channels angles Tees,

flats, with connecting plates or angles cleats as in main and cross

beams. Hip and jack rafters, purlins connected to common rafters

28 Supply & installation ISI marked (IS:15683) Fire Extinguisher, 5.00 Each 6058.28

Carbon-di-oxide type capacity 4.5 Kgs. flat base including valve,

discharge hose of not less than 10mm dia., 1M long and complete

in all respects including initial fill with CO2 gas conforming to

IS:307-1966 filled to a filling rate of not more than 0.667 and wall

suspension bracket. (LMR) etc completed as directed EIC.

29 Supplying & fixing 6 Kg. Capacity ABC Dry Chemical powder 5.00 Each 3188.57

Stored Pressure type fire Extinguisher As per I.S-15683 having ISI

marked Etc. complete as Directed by EIC

30 Supplying & fixing 9 ltr. Capacity WCO2 Stored Pressure type fire 5.00 Each 4949.00

Extinguisher As per I.S-15683 having ISI marked Etc. complete as

Directed by EIC

31 Design, Supply & Installation of Safety Signage approved make 18750.00 Sq.cm. 2.65

made of zinc sulphide based glow in the dark rigid sheet with high

luminous property enclosed in a transparent weather proof U/V

stabilized plastic pasted on 3mm thick clear acrylic sheet/ foam

sheet such as ASSEMBLY POINT, EXIT, EMERGENCY EXIT, DO

NOT USE LIFT IN CASE OF FIRE, FLOOR MARKINGS, FIRE

LIFT, STAIRCASE EXIT, STAIRCASE STRIP, FIRE ALARM CALL

POINT, FIRE EXTINGUISHER, FLOOR EVACUATION PLAN etc.

completed as directed by engineer in charge.

It. No. Description of Item Quantity Unit Rate in Figure Total

32 Supplying, installation, testing and commissioning sector panel 3.00 Set 8311.86

suitable for following zones, complete with visual indications for

short circuit fault, Open circuit fault, fire condition and all other

standard facitilites, as per IS: 2189 with mimic diagram for all area /

zone covered, complete with all connections, interconnections as

33 Supplying, installation, testing & commissioning of smoke detector 45.00 Each 1036.44

with builtin LED and mounting base complete with all connections

etc. as required

34 Supplying, installation, testing & commissioning of manual call 9.00 Each 434.75

boxes of MS construction in surface/recess with stainless steel

chain & hammer assembly complete with glass and push button

etc. as required.

35 Supplying, installation, testing & commissioning fire alarm sounder 9.00 Each 449.15

with facility to make announcement, mounted in A.B.S. box with

hinged cover plate & suitable for operation with amplifier i/c line

matching transformer etc. complete as required.

36 Supplying, installation, testing & commissioning of response 9.00 Each 188.14

indicator on surface/recessed MS 36 Box having two LED, metallic

cover complete with all connections as required.

37 Supplying & Laying of 2 x 1.5 sq., mm fire alarm armoured cable, 1100.00 Mtr. 162.71

600 / 1000 V rated with annealed copper conductor having XLPE

insulation, steel wire armouring & FRLS outer sheath complete as

38 Providing, Fixing & installation PVC 100x100mm junction box for 45.00 Each 212.10

smoke detector including fixing in ceiling with all labour & materials

as directed by engineer in charge.

39 Labour charges for Professional & Administrative Charges for 1.00 Job 50500.00

engaging manpower for giving testing in front of Fire Department

and Fire Testing & Liasoning with Fire Department to getting Fire

and Safety Certificate for existing Fire Fighting System include.

engaging skilled labour & skilled supervisor for testing of all fire

system on site with operating pump/panel & existing FA system.

The testing should be done in the presence of PWD authority as

well as Fire Department with required pressure of 3.5 KG pressure

at farthest point. Also testing should be done at every floor with all

installed equipment before final testing. As built fire drawing to be

submitted by bidder to PWD Authority after completion of the work.

Manufacturer Test Certificate attached at the time of RA Bill and

Note - Goverment Official fees and hidden charges shall be extra

at actual to getting fire NOC

40 Providing and fixing SS - 304 Crome Finished Ball valve 25mm dia. 9.00 Each 1069.92

41 Providing, lifting (Terrace Floor) & fixing PVC Three /Four layer 5000.00 Liter 12.88

water tank of required capacity with all necessary fitting and

connection etc. Complete on terrace cabin at any level and at any

height as directed by engineer in charge.

42 Providing laying and jointing in true line and level 40mm dia. 12.00 Mtr. 148.12

U.P.V.C. Pipe ( SCH- 40) for cold water including fittings make

PRINCE / SUPREME / ASTRAL / FINOLEX or equivalent as

approved by Engineer In Charge. Pipe shall be fixed on the wall

with the help of clamp at every two metre C/C or shall be concelled

as directed including necessary fittings etc. including testing of pipe

and joints and fixing the same with adhesive solvent, including cost

of all materials.

It. No. Description of Item Quantity Unit Rate in Figure Total

43 Providing laying and jointing in true line and level 50mm dia. 8.00 Mtr. 195.67

U.P.V.C. Pipe ( SCH- 40) for cold water including fittings make

PRINCE / SUPREME / ASTRAL / FINOLEX or equivalent as

approved by Engineer In Charge. Pipe shall be fixed on the wall

with the help of clamp at every two metre C/C or shall be concelled

as directed including necessary fittings etc. including testing of pipe

and joints and fixing the same with adhesive solvent, including cost

of all materials.

44 Providing and fixing UPVC check or ball valve 25mm dia 1.00 Each 339.56

45 Providing and fixing UPVC check or ball valve. 50mm dia. 6.00 Each 418.24

46 Supply Installing Testing & Commissioning of M. S. 18 guage hose 10.00 Each 4411.74

box to accommodate of 2-Nos 15-Mtrs. Length Hose Box pipe &

No. of branch pipe with Nozzle, With necessary fabrication support

and joints and 3 mm glass shutter including poweder coating etc.

complete as directed by engineer in charge.

Rs. Twenty Four Lakhs, Ninety Thousand One Hundred Fifty Six and Sixty Five Paisa Only

I/We am/are willing to carry out the work @ ______________ % ______________ percent

(should be written in figures and words) below / above, the estimated rates mentioned above, amount of

my/our tender works out as under :

Above all items of "Bill of Quantities" with Item Description, Unit, Qty, Rate & Amount have verified by me and

1 The Contractor shall exhibit a board with detailed specification and details of work as directed by the

Engineer-In-Charge for which no extra payment shall be made.

2 The labour cess will be deducted as per prevailing rules i.e. 1% of the work done.

3 GST and Income tax TDS will be deducted at a source while making payments of bills.

4 In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per Govt. G.R.: PRC-

10/2017 Cement Consumption/16/C, Date:11/05/2017 as stated in S.O.R. therefore in R.C.C. items where

there is a change as per actual mix design the cost of difference of cement consumption have been deducted

from the rate of original item at the rate of input rate mentioned in all the tender.

5 The contractor will have to submit the mix design for different grades of cement concrete and

asphalt at his own cost before execution as directed and to be approved from the engineer in charge.

Deputy Executive Engineer Executive Engineer

Dabhoi (R&B) Sub Division District (R & B) Division

Dabhoi Vadodara