CONSTRUCTION OF GUARD REST ROOM FOR 01 CDR, 06 x OR AND TOILET BLOCK IN CBRN/TRAINING AREA FOR TRAINEES AT K AREA UNDER GE CHANDIGARH

Amount

Excavating in trenches, n exc 1.5m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5m in depth and getting out complete all as specified and directed.

M&L for PCC 1:4:8 type D2 ( 40 mm graded aggregates) Cement concrete in foundations, filling and mass-concrete etc complete all as specified and directed.

M&L for RCC M-25 design mix using 20 mm graded aggregate in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

M&Lfor RCC M-25 design mix (using 20 mm graded stone aggregate) as in columns pillars, posts and struts etc complete all as specified and directed.

M&L for RCC M-25 design mix using 20 mm graded aggregate in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

M&L for RCC M-25 design mix using 20 mm graded aggregate in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

As per item No. 6 as above but Chajjas

Use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter flat surfaces complete all as specified and directed.

Use and waste of formwork to the sides of pillars, posts, struts, piers, columns complete all as specified and directed.

Use and waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. complete all as specified and directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings & similar work; not exc. 200mm thick (Horizontal or sloping) Rough finished surfaces of concrete flat complete all as specified and directed.

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide complete all as specified and directed.

M & L Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to TMT bars complete all as specified and directed.

As per item No.13 but 6mm to 8mm dia

Material & labour for mild steel high yield strength TMT bars 5mm dia and over upto and including 10mm dia as in stirrups, spacers, binders etc cut to length bent to shape required, including cranking, hooking ends, bending and binding with and including MS wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

M&L for Brickwork with fly ash bricks straight or curved on plan exc 6 m mean radius in cement mortar 1:4 omplete all as specified and directed.

M&L cement concrete (1:3:6 ) type C-2 using 40 mm graded stone aggregate as in foundation filling and mass concrete complete.

Sand filling under floors or in foundations including watering and consolidation omplete all as specified and directed. . Note : Sand obtained from excavation shall be used for filling

Removing excavated material distance exc. 250 m but n exc. 500 m and depositing where directed at a level n exc. 1.5 m above the starting point in soft/loose soil.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm.in any type of soil all as specified and directed.

M&L broken stone & boulders hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface

M&L 75mm thick PCC type D-2, (1:4:8) using 40mm graded stone aggregate omplete all as specified and directed.

M&L for 75mm thick PCC (1:3:6 ) type C-1 using 20 mm graded stone aggregate as in plinth protection laid in panels finish the top surfaces even and smooth without using extra cement

M&L for 50mm thick PCC (1:3:6 ) type C-2 using 40 mm graded stone aggregate as in plinth protection laid in panels finish the top surfaces even and smooth without using extra cement

M&L for 25 mm thick cement concrete 1:2:4, type B-1(using 20mm graded stone aggregate) as profile corrective course in flooring with rough finish complete all as specified and directed.

M&L Rendering 15mm thick plaster in cement mortar 1:6 on brick or concrete masonry walls, finished even and fair without using extra cement complete all as specified and directed.

M&L Rendering 15mm thick plaster in cement mortar 1:4 on brick or concrete masonry walls, mixed with water proofing compound on fair faces of brick work or concrete surfaces, finished fair & even without using extra cement complete all as specified

All as item no. 27 above but 10mm thick in CM (1:3) over RCC surfaces as on ceiling

M&L for applying two coats of oil bound distemper over 1-2mm thick wall putty including a coat of alkali resistant priming paint incl preparation of new plastered surfaces of wall complete all as specified and directed.

M&L for preparing newly plastered surfaces and applying two coats of Appex, super quality (to Exterior surfacesof wall) over a coat of primer, all as specified

M&L for preparation of newly plastered surfaces and applying three coats of white wash on ceiling surfaces complete all as specified.

M&L for Marble work 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, windowcills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade of Bhaislana Zebra including 10mm thick baking layer in cm 1:4 complete all as specified

Supply and fixing factory made UPVC door frame made of uPVC. extruded sections having an overall dimension (extruded section profile) 42x50 mm (tolerance ± 1 mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete all as specified by the manufacturer and as per directions of Engineer-in-charge

Supply and fixing factory made UPVC white colour Casement door with 3D hinges made of (big series) frame 67 x 64 mm & sash 67 x 110 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door upto 2.00 sqm) comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws, etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality complete all as specified and directed by Engineer-in-Charge. (Glass shall be paid separately) Note: For UPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

S&F Providing and fixing factory made UPVC white colour Sliding window Three track (area exceeding 2.00 sqm each ) made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories. Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net Opening will be measured lor payment purpose.

Supply and fixing factory made UPVC white colour Casement door with top hung ventilator with 3D and SS friction (400 x 19 x 1.9 mm) made of (big series) frame 67 x 64 mm, sash 67 x 110 mm & mullion 67 x 80 mm all having wall thickness of 2.3 + 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door upto 2.50 sqm) comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws, etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality complete all as specified and directed by Engineer-in-Charge. (Glass shall be paid separately)

S&F 5.5mm thick Sheet glass, ordinary quality and glazing with and incl gasket and connected fittings in square n exc 0.5sq. m in each pane complete all as specified and directed.

All as per item No. 37.00 above but exc 0.5 sqm in each pane complete all as specified and directed.

S&F 4.00 mm thick Frosted Sheet glass,ordinary quality and glazing with and incl gasket and connected fittings in square n exc 0.5 sq. m in each pane complete all as specified and directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, in opening as per specification & drawing complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles & plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame welded/ sealed to the stiles, & rails with suitable PVC sheet beading, & joined together with solvent cement, in the frame at site as per specification & drawing.

S&F 200mmAluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F 250mm Aluminium alloy, anodised, sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

S&F 150mm Aluminium handles, cast type anodised complete all as specified complete all as specified and directed.

S&F for 125mm Butt hinges, heavy weight, cold rolled mild steel, and fixed complete all as specified and directed.

M&L for coloured Virified Ceramic tiles 8-9 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, colour of tiles over and including screed bed or bedding layer of 15mm thick in CM (1:4) , complete all as specified and directed .

All as per ser item No 46.00 but in vertical surfaces such as skirting over and including 10 mm thick rendering in CM (1:3) , complete all as specified and directed .

S&F Coloured Non Skid ceramic tiles 7 to 8mm thick (squares/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed in CM(1:6) complete all as specified and directed.

S&F Coloured Glazed ceramic tiles in vertical surfaces 450x350x7mm / 600x300x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10mm thick plaster in CM(1:4) complete all as specified and directed.

S&F for cast iron 100mm bore sand cast soil waste or vent pipe as in any length with or w/o ears with cement joints laid in trenches or in floors complete all as specified and directed.

All as item no. 50.00 above but fixed to walls

S&F cast iron 75mm bore sand cast soil waste or vent pipe as in any length with or w/o ears with cement joints laid in trenches or in floors complete all as specified and directed.

S&F cast iron 100mm bore sand cast bends (any radius) and straight connecting piece complete all as specified and directed.

S&F Cast iron 75mm bore Bends (any radius) with duck's foot or heel rest complete all as specified and directed.

M&L Cast iron floor trap 75mm dia, with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified and directed.

S&F 15mm bore medium grade tubes, galvanized with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed.

S&F 20mm bore medium grade tubes, galvanized with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed.

S&F chromium plated Jet Spray (Butterfly) with 1.5mtr tube, complete all as specified complete all as specified and directed..

S&F cromium plated soap dish with chromium plated brass screws in Bathrooms and for wash hand basins complete all as specified and directed..

Supply & fix in repairs vitreous china wash down water closet pan (pedestal pattern) white including plastic water closet sheet cover white, closed pattern with flat bottom, with mild steel chromium plated or aluminised hinging device and including mild steel chromium plated jet fixed to water closet with 360mm wide x 390mm high and 415 to 445mm long flexible pipe complete all as specified and directed.

S&F Belmonte Ceramic Vitreous China wash basin oval shape Table Top/over Counter vessel 500 x 380 x 120mm with CP waste coupling & pipe complete all as specified and directed by Engr-in-Charge.

Supply & fix vitreous China wash hand basin white flat back, size 550mm x 400mm, cutting for and pinning in ends of brackets Including 32mm bore waste pipe, brass coupling, ,chromium plated brackets, restoring all connections complete all as specified.

Supply & fix PVC white low level flushing cistern 10 ltr capacity with all fittings syphonic action with top push type button with inlet ball valve and float including flush pipe, ball valve, handle, bracket PVC short bend etc. complete all as specified and directed.

S&F 15mm dia bib tap, chromium plated brass, fancy type with crutch or butterfly handle, screwed down complete all as specified and directed.

S&F 15mm dia CP Center hole mixer (for hot and cold water), screwed for iron pipe complete all as specified and directed.

S&F 15mm bore CP angle cock/Stop valves fancy type,screwed down,high pressure,with crutch or butterfly handle,screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

M&L brass chromium plated shower rose 125mm size with or without swivel joints with shower arm 15 mm size, 195mm long with bend of 45 degree with flange , including fixing to steel pipe or union complete all as specified and directed.

S&F CP Conceled stop cock complete set with fittings, complete all as specified and directed.

S&F chromium plated towel rail 60 cm long 20mm dia with flanges complete all as specified and directed.

S&F PVC connection 15mm size with PTMT Nuts of length 450mm complete all as specified and directed.

S&F rotational moulded polyethylene (tripple Layer) water storage tanks 1000 Ltr capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I, complete all as specified and directed.

S&F 20mm ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed complete all as specified and directed by Engr-in-Charge

S&F Chromium plated Brass 2 in 1 health faucet with hook 1 mtr tube all as specified and directed by Engr-in-charge.

S&F chromium plated (CP) toilet paper holder complete all as specified and as directed complete all as specified and directed.

M&L for Granite 20 mm thick (of any tpe) work (table rubbed and polished) in WHB platform, steps, jambs, pillars, window cills,cooking platforms and like incl rounding or bullnosing the exposed edges over 15 mm thick screed in CM 1:3, complete all as specified.

S&F Glass corner shelf, one set comprises of three pieces of corner shelf fancy type (small to large) 250 x 250mm, 200 x 200mm, 150 x 150mm) with all fittings,complete all as specified.

S&F white vitreous china half stall type urinal complete with 32mm size CP waste coupling, PVC waste pipe and urinal spreader fixed to walls complete all as specified and directed..

S&F urinal spreader of PTMT any colour for fixing with 15mm dia pipe (minimum weight 60 gms) complete all as specified and as directed. .

M&L for rendering 10mm thick in cm 1 : 3 mixed with liquid water proofing compound as per manufacturers instructions on concrete/brick surfaces finished even and smooth without using extra cement complete all as directed (WPC measured and paid separately) complete all as specified and as directed.

Supply only water proofing compound ISI marked complete all as specified.

M&L for providing roof treatment as under : - (a) Applying bitumenous primer @ 0.30 litres per sqm over cleaned and dry roof surface including parapet. (b) Material and labour for providing and laying 3mm thick APP modified polyester reinforced water proofing membrane with minimum weight of 3.60 kg/sqm , as specified. The APP membrane shall be laid using torch-on application with minimum 10 cm side overlap and 15 cm end overlap. The APP memberane shall be fixed with termination bar and fasteners and end shall be properly sealed with sealant. The rain water gutter portion shall be finished with cement mortar 1:4 to provide requisite slope towards rain water pipe outlet complete all as specified and directed..

S&F 20 mm gate valves of gun metal with iron wheel head screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F 15 mm gate valves of gun metal with iron wheel head screwed both ends for iron pipe and fixed complete all as specified and directed.

M&L for Salt-glazed stoneware gully,traps, 100 X 100 mm square or round mouthed, tvpe 'P'including all excvation and earthwork comcrete in beds,surrounds,kerbs etc setting in cement mortar 1:1 complete all as specified and directed.

S&F PVC waste pipes 32 /40 mm suitable for basins/ sink / urinals complete all as specified and directed.

M&L for providing Pre-cast cement concrete louvres and jallies 25mm thick (measured solid) Type B0 1:2;4 (using 12.5mm graded aggregate) set in CM 1:4,, including all mouldings, all as specified

M&L for cement concrete 1:2:4 type B-1 (using 20 mm graded stone aggregate as in copings complete complete all as specified and directed.

Cement concrete Type B2 1:2:4 (using 20 mm graded stone aggregate) in surface channels and drains complete all as specified and directed.

Concrete bed to drain pioes including packing under, and haunching against the sides of pipes after they are laid and tested. (Cement concrtete 1:3:6 type C-2 bore of pipe in 150mm) complete all as specified and directed.

S&F reinforced concrete pipes with collars, 150mm bore, class NP2, laid, jointed and tested after laying complete all as specified and as directed. Note : Earthwork shall be measured & paid separately

M&L for providing & fixing of precast RCC 1:2:4 type B-1, 1:2:4 (20mm graded stone aggregate) as in cover slabs (for manholes etc) of any size & thickness set in cement mortar 1:6 complete all as specified and directed by Engr-in-Charge.

M&L for Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft soil, complete all as specified and directed

Material & labour for 60mm thick machine pressed precast concrete interlocking paver block and shape and size confirming to IS 15658-2006 of M-35 Grade with grey cement and pigment over sand cushioning complete all as specified and directed. The Interlocking Paver blocks shall be procured directly from one of the Manufacturers specified. Note:-The sample shall be got approved from the GE before bulk procurement and lots shall be got tested independently by the GE.

M & L Providing, cement concrete Type B1 1:2:4 (20 mm graded aggregate) in roof kerbs or mud stops, rounded or chamfered on edges, complete all as specified and directed by the Engg -in charge.

M & L Providing precast cement concrete in kerb stone of Typ B1 1:2:4 (20 mm graded aggregate)(of section 450 x 450 x 150 mm), with plain fair faces, including chamfers, weatherings, throat- ing etc. and setting in mortar 1:4 complete with joints to match all incl necessary excavation and returning filling, as specified and as directed by the Engg -in charge.

Brickwork with sub-class `B' brick straight or curved on plan to any radius in half brick thick walls built in CM (1:4) all as specified and directed by the Engg -in charge.

S&F factory made box type steel windows / ventilators with side hung shutters including hinges, steel handle, steel peg stay and MS tower bolt 150mm long complete with glazing bars , dovetailed or welded as per Drg No TD-219 of HQ CE CZ Chandigarh complete all as specified and directed.

S&F Galvanised mild steel wire cloth, 0.56 nominal dia of wire & average width of aperture 1.18mm with tinned tacks, or galvanised wire staples all as specified and directed by the Engg -in charge.

S&F Sheet glass 3.0mm thick, ordinary quality & glazing with oil putty in square n exc 0.5 sq.m in each pane all as specified and directed by the Engg -in charge.

S&F framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks & similar work conforming to Fe 290-0 Gde E-165 all as specified and directed by the Engg -in charge.

M&L 75mm thick PCC type C-2, (1:3:6) using 40mm graded stone aggregate all as specified and directed by the Engg -in charge.

S&F 15mm dia pillar tap, chromium plated brass, fancy type with long screwed shanks and fly-nuts, screwed for iron pipe complete all as specified and directed.

S&F rotational moulded polyethylene (tripple layer) water storage tanks 500ltr capacity (Cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I, complete all as specified and directed.

M&L for preparing new untreated steel or iron surfaces over 10cm width or girth and applying two coats of synthetic enamel paint over factory coat of primer, all as specified and directed by Engr-in-Charge.

M&L for three coats of white wash on walls after preparation of newly plastered surfaces on walls all as specified and directed by the Engg -in charge..

M&L for two coats cement base paint on newly plastered, undecorated surfaces of walls including preparation of new plastered surfaces complete all as specified and directed by the Engg -in charge.

M&L for steel water tubing , galvanised , medium grade , ISI marked , 50mm bore with and including all fittings laid in trenches complete all as specified and directed by the Engg -in charge.

M&L for steel water tubing galvansied , medium grade , ISI marked 20 mm bore with and including all fittings laid in trenches complete all as specified and directed by the Engg -in charge.

M&L for Gun metal,globe or gate valves with iron wheel head screwed both ends , Class II suitable for iron pipe and fixed for 50 mm bore dia complete all as specified and directed by Engineer -in-Charge.

Construction of brick masonary valve pits of size 600 mm x 600 mm x 600 mm (internal dimension of chamber), depth of chamber to be recokoned from the top of PCC in foundation to top of MS cover as shown in drg with and including MS sheet cover fabricated from 3 mm thick MS sheet and frame of angle iron 40 mm x 40 mm x 5 mm with fixing arrangement hinges and locking arrangement and painting two coats of synthetic enamel paint over a coat of red oxide primer after preparation of surfaces on MS cover and frame including necessary excavation and earth work in any type of soil, returning, filling in approved soil, disposal of surplus soil to a distance not exceeding 50 metre, 150 mm thick PCC 1:4:8 type D-2 using 40 mm graded stone aggregate as in foundation, brick work using bricks as mentioned in PS clause 5.1 in cement mortar 1:6, 15 mm plastering in cement mortar 1:4 both internally and externally 30cm below GL, 100 mm thick PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in flooring complete all as specified and directed by Engineer-in-Charge.

Cutting the CI pipe in position for insertion of new tees, branches etc of size 100mm bore complete all as specified and directed by Engineer -in-Charge.

Supply and laying for cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables ( heavy duty ) 1100 volts grade with stranded aluminium conductor of size 25 Sqmm 3.5 core (Distribution Cable) complete all as specified and directed by Engineer -in-Charge.

Supply and errection of steel tubular swaged poles , 09 mtr long, type -410 SP-31 confirming to IS 2713 applying 2 coats of aluminium paint over a coat of red oxide primer externally above ground level and a coat of anti-corrosive paint below ground level and marking with alternate white and black paint strip 30 cm wide-total 05 Nos with synthetic enemal paint complete with and including provision of CI base plate, final taper plug bolts, nuts, screws, drilling works including numbering to poles, erected & fixed in vertical position complete all as specified and directed by Engineer-in-Charge. Note :- Excavation, PCC in foundation/plinth block/ coping cross arms, bracings, clamps etc shall be measured and paid separately.

Supply and fixing LED street light fitting 60 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete including street light mounting bracket with light grde GI pipe 32mm dia all as specified and directed.

S&F MS Box with Aluminum bus bar 32 Amp 1100 V complete of size 90mmX90mmX60mm of 3.15 mm thick sheet complete all specified including twin core PVC copper wire 1.5 sqmm with suitable size of PVC conduit from junction box to street light complete all as specified.

Steel water tubing, galvanised, light grade, ISI marked, 50 mm bore with and including all fittings fixed to walls and ceilings or laid in floors complete all as specified and directed by Engineer-in-Charge.

Excavation in trenches in soft/loose soil exceeding 1.50 meter wide and not exceeding 3.0 meter in depth and not exceeding 10sqmm on plan and getting out complete all as specified.

M&L for plain cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate as in foundations of PCC poles/struts, stay asembley, filling and mas concrete etc. including necessary fromwork complete all as specified and direted by Engineer-in-Charge.

Sand filling under floors or in foundations including watering and consolidation complete all as specified and directed by Engineer -in-Charge.

Supply and laying burntbricks sub class "B" old size for cable protection laid flat lengthsise perpenducualr to the axis of cable complete all as specified and direted by Engineer-in-Charge.

Earthing complete with and including galvanised steel earth plate electrode 600 mm x 600 mm x 6 mm surrounded by a mixture of charcoal and salt in alternate layers burried directly in ground vertically in a pit of depth not less than 2.25 m deep below ground level with top edge of earth plate at a depth of not less than 1.5 m below ground level, connected with and including galvanised iron or steel earth wire, 4mm dia (No. 8 SWG) by means bolts, nuts, check nuts and washers made out of galvanised iron, 15 mm bore (light grade) GI pipe for protection of earthing lead, 20 mm bore (light grade) GI pipe for watering with funnel, wire mesh and including necessary excavation and earth work, PCC 1:2:4 type B-1 pit and 50 mm thick RCC M-25(Design mix) reinforced with XPM (weight not less than 3 kg/sq m) pit cover, C.I frame, charcoal and comman salt filling in alternate layers, complete all as shown and specified in electrical plate No. 3 of SSR Part-I (2009) complete all as specified and directed by Engineer-in-Charge. Note : (i)The unit rate includes for protecton pipe 15mm and GI earth strip 4mm from top of earth plate upto 7.50 metre above ground level. (ii) If desirable earthing result not found re done earthing without any extra charge until get required earth resistance. (iii) The result sheet of earthing may submit to sub division level by contractor.

Earthing complete with galvanized steel earth plate electrode 600x600x6mm surrounded by mixture of charcoal and salt in alternate layers burried directly in ground vertically in a pit of depth not less 2.25mtr below ground level with top edge of earth plate at a depth of not less than 1.50mtrs below ground level connected with and including 32x6mm galvanized iron strip as earthing lead by means of bolts, nuts, check nuts and washers made out of galvanized iron, 20mm dia medium grade GI pipes for watering with funnel, wire mesh and 40mm GI light grade protection pipe for GI strip and including necessary excavation, earth work, PCC 1:3:6 type C-2 concrete pit and RCC pit cover charcoal and common salt filling in alternate layers complete all as specified and directed by Engineer-in-Charge on electrical plate no-3 of SSR Par-I of 2009. Note:(i) If desirable earthing result not found re done earthing without any extra charge until get required earth resistance. (ii) The result sheet of earthing may submit to sub division level by contractor.

Supply and instaltion Eco Fire ABC powder type (stored pressure) fire extinguisher 5KG conforming to IS code-15683 operating temperature 0 to +55 and fire rating 2A & 21B type of fire filled MAP powder complete in all respect and A,B,C class fire inflamemable liquids (petrol,kerosene,paints and diesel) gasesous fire LPG and actylene and electrical fire,paper,cloths,wood complete all as specified and directed by Engineer -in-Charge.

Supply and fixing fire bucket made of galvanised iron sheet of thikness 18 SWG capacity 09 ltr (For Water).Treated with anticorrosive treatment design as per IS:2546 painted with one coat of red oxide and primer and two coats of fire red paint and writing fire on the outer side of the buckets complete all as specified and directed by Engineer -in-Charge.

Supply and fixing fire bucket (for sand) design as per IS:2546 suitable for four buckets complete all as specified and directed by Engineer-in-Charge.

Supply only fire beater complete with solid hard wood handle specification all as per IS:8096 of 1992 complete all as specified and directed by Engineer -in-Charge.

M&L for point wiring using approved colour coding as per IS (For phase and neural), with stranded copper conductor 1.5 Sqmm (nominal area), single core, multistranded, FRLS, PVC insulated and unsheathed cable 1100 volts grade, ISI 694 marked drawn in and including heavy duty PVC concealed conduit with fittings ISI marked, terminated in junction box incl 1.5 Sqmm (Nominal area) single core, multistranded, FRLS, PVC insulated and unsheathed cable as earth continuity conductor to common earth and connected to earth dolly complete all as specified for One light/fan point controlled by one switch & fan regulator.

All as per item No. 128.00 above but One socket outlet three pin, 5 Amps on the same board complete all as specified and directed.

All as per item No. 128.00 above but One socket outlet three pin, 5 Amps, independent complete all as specified and directed.

All as per item No. 128.00 above but One bell or buzzer controlled by one bell push complete all as specified and directed.

M&L for point wiring using approved colour coding as per IS (For phase and neutral), with stranded copper conductor 2.5 Sqmm (nominal area), single core, multistranded, FRLS, PVC insulated and unsheathed cabel 1100 volts grade, ISI 694 marked drawn in and including heavy duty PVC concealed conduit with fittings ISI marked, terminated in junction box incl 2.5 Sqmm (Nominal area) single core cable as earth continuity conductor to common earth and connected to earth dolly complete for one power point 14 Amps all as specified.

M&L for point wiring using approved colour coding as per IS (For phase and neutral), with stranded copper conductor 4 Sqmm (nominal area), single core, multistranded, FRLS, PVC insulated and unsheathed cabel 1100 volts grade, ISI 694 marked drawn in and including heavy duty PVC concealed conduit with fittings ISI marked, terminated in junction box incl 4 Sqmm (Nominal area) single core cable as earth continuity conductor to common earth and connected to earth dolly complete for one power point 14 Amps all as specified.

Supply and fix Switch modular type single pole one module, 6 Amps complete all as speciifed.

Supply and fix Switch modular type single pole one module, 16 Amps complete all as speciifed.

Supply and fix Socket outlet mdoular type, multipurpose, 2/3 pin, single pole two module, 6 Amps complete all as speciifed.

Supply and fix Socket outlet mdoular type, multipurpose, 2/3 pin, single pole two module, 6/16 Amps complete all as speciifed.

Supply and fix single pole and neutral encolsure with two pin and earth plug with socket complete with one single pole MCB 20 Amp 240 Volts complete.

Supply and fix Modular bell push single pole one module, 6 Amps complete all as speciifed.

Supply and fix Bell ding dong AC 230 volts PVC polycarbonate insulated body complete all as specified.

Supply and fixing LED lights fitting 1x 18W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

Supply and fix Lamp holder insulated body with back plate for batten fittings with LED lamp 9 watt complete all as specified and directed.

Supply and fix ceiling fans, complete with three blade, down rod, accessories 230V, 1200mm sweep, with Squirrel cage induction motor complete all as specified and directed.

Supply and fix Modular fan Step type regulator 120W 2 Module complete all as specified and directed.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 380mm sweep with, blades, and frame and louvers complete all as specified and directed.

Supply and fix Ceiling rose 3 pin, 230 volts PVC polycarbonate insulated body complete all as specified.

Supply and fix Modular metal flush terminal boxes with lumina plate and frame suitable for 1 module complete all as specified and directed. Make :SSK/Legrand/Anchor

Supply and fix Modular metal flush terminal boxes with lumina plate and frame suitable for 2 module complete all as specified and directed. Make :SSK/Legrand/Anchor

Supply and fix Modular metal flush terminal boxes with lumina plate and frame suitable for 3 module complete all as specified and directed. Make :SSK/Legrand/Anchor

Supply and fix Modular metal flush terminal boxes with lumina plate and frame suitable for 4-5 module complete all as specified and directed. Make :SSK/Legrand/Anchor

Supply and fix Modular metal flush terminal boxes with lumina plate and frame suitable for 6 module complete all as specified and directed. Make :SSK/Legrand/Anchor

Supply and fix Modular metal flush terminal boxes with lumina plate and frame suitable for 8 module complete all as specified and directed. Make :SSK/Legrand/Anchor

Supply and fix Modular blank plate one module all as specified and directed.

Supply and fix MCB DB sheet metal encolsure Triple pole and Neutral 4 way double door 415 Volts all as specified and directed.

Supply and fix MCB TPN/FP, 'B' series. 10 KA, 415 Volts 40 to 100 Amps capacity all as specified and directed.

Supply and fix MCB SP, 'B' series. 10 KA, 240 Volts, 6-32 Amps capacity all as specified and directed.

Supply and fix electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, hermostate, NRV, connection piece etc. all as specified and directed Make : Havells/Venus/Crompton

Supply and fix bulk head light 9 watt LEd type including bulb all as specified and directed.

Removing of surplus soil/excavated material to a distance not exceeding 50meter and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified.

Steel water tubing galvansied , medium grade , ISI marked 25 mm bore with and including all fittings laid in trenches complete all as specified and directed by Engineer - In - Charge

Gun metal , globe or gate valves with iron wheel head screwed both ends , Class II suitable for iron pipe and fixed for 25 mm bore dia complete all as specified and directed by Engineer -in-Charge.

Cutting the CI pipe in position for insertion of new tees, branches etc of size 100mm bore

Supply and fix MCB DB sheet metal encolsure single pole and Neutral 4 way double door 240 Volts all as specified and directed.

Supply and fix MCB SPN 'B' series. 10 KA, 240 Volts 32 Amps capacity all as specified and directed.

GURU NANAK CONSTRUCTION CO.

RAJESH KUMAR

SS BUILDERS