GE/KHU-61/2025-26 SPL REPAIR TO BLDG NO T-31, SPL REPAIR WALL PANELLING TO BLDG NO T-08, SPL REPAIR TO BLDG NO T-05, SPL REPAIR TO BLDG NO T-10 AND ADDN ALTN TO BAR COUNTER OF BLDG NO T-53 IN THE AOR OF B/R-I KHUMBATHANG UNDER GE KHUMBATHANG

Amount

Dismantling of wall and ceiling boards (fibre pulp, insulation, etc.) or insulation boards/slabs/ lankets, any thickness, including cover fillets complete all as specified and directed.

M& L for 9 mm thick Prelaminated particle board, interior grade, prelaminated one side with ecorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work

M& L for 11/12 mm thick Prelaminated particle board, interior grade, prelaminated one side with ecorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work

Dismantling of timber scantlings in fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section complete

M & L fo 2nd class hard wood timber scantling plain fillets. square, rectangular or triangular in section area exc 13 sqcm not exc25 sqcm , clean sawn, secured with nails or brads complete.

M & L fo 2nd class hard wood timber scantling plain fillets. square, rectangular or triangular in section area exc 3 sqcm not exc 6 sqcm , clean sawn, secured with nails or brads complete.

M & L fo 2nd class hard wood timber scantling plain fillets. square, rectangular or triangular in section area notb exc 3 sqcm , clean sawn, secured with nails or brads complete.

Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings

S& F Pre-painted galvalume aluminum zinc coating GI based Plain steel heet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

S& F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.5mm thick of any colour having tensile strength of 550 Mpa as in roof covering/including rain guard cladding to wall,fixed with self tapping screws as specified..

M&L for preparing old steel surfaces of any description not otherwise described over 10cm in width or girth and applyingapplying one coats of synthetic enamel paint complete all as specified

Preparation of old wooden or wood based surfaces of any description, over 10cm width or girth and applying a coats of synthetic enamel paint complete all as specified and directed.

Demolition of cement concrete in ground floor & paving n. exc 15 cm thick (below or above GL) unreinforced complete all as specified and directed.

M&L for 25mm thick PCC 1:2:4 type B-0 using 12.5 mm graded crushed stone aggregate as in pcc padding complete all as specified and directed.

M/L 75mm thick cement concrete type D-2, 1:4:8 for sub base all as directed.

Chequered cement concrete tiles 30cmx30cmx20 mm thick, set,jointed and pointed in neat cement slurry in floors.with grey cement and pigment over and incl 15 mm screed in 1:6 cm complete all as specified and directed.

Demolition of cement concrete block walling built in cement mortor complete all as specified and directed.

M& L pre-cast cement concrete block(1:3:6) type C1 using 20 mm graded aggregate ) masonry with solid blocks, exc. 10 cm in width and setting in1:6 cement mortar, complete

M & L for Rendering 15mm thick on brick or concrete surface or other than fair faces of brick work on wall in CM 1:4 surface finished even and smooth w/o extra cement

M&L for preparing new plastered surfaces of walls and applying two coat of cement based paint over a coat of primer complete all as specified

M & L for Rendering 15mm thick on brick/stone masonery or other than fair faces of brick work on wall in CM 1:6 surface finished even and smooth w/o extra cement

M&L for preparation of new plaster surfaces of walls and applying two coat of oil bound distemper over a coat of primer complete all as specified

M&L for TMT bars10mm dia and over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with theincluding mild steel wire (annealed) not less than 0.9mmdia or securing with clips quality complete all as specified and direceted.

Ditto all as per Item no-6 above but 5mm dia and over upto and including 10 mm dia complete all as specified & directed.

M& L for Rcc 1:2:4 type B1 (20 mm graded stone aggregate ) nominal mix Beams, roof beam, cantilevers, bressumm?ers, lintels over 1.5m span

M&LUse and waste of formwork to rough finished flat surfaces of concrete foundations, footings , bases of coulmns, rafts and raft beams, sides and soffits (if any) of foundation and plinth beams ; and other similar works; vertica or to batter complete all as specified and directed.

Rounding to edges of stones slabs one edge,such as in steps, cooking platform and other similar situations complete all as specified and directed.

M&L for granite (of any colour) 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixure of pigment to match the shade of granite stone including grinding and polishing over & incl 15 mm screed bed 1:6 complete, in kitchen platform, flooring and all other similar works complete all as specified and directed.

M&L 75 mm thick PCC 1:3:6 type C1 using 20 mm graded stone aggregate as in plinth protection finished even and smooth without using extra cement including necessary complete all as specified and directed.

Supply & fixed in repairs stainless steel 25 mm dia curtain rod with fixing side brackets, end cups, and fixed with PVC rawl plugs & steel screws complete all as specified and directed.

Taking down of unserviceable Aiuminium door with frame (without taking down shutters and grill from frame) of size exc 1.50 sqm each including cutting holes of appropriate size for insertion blocks of cement concrete hold fasts complete all as specified and directed.

S& F Powder coated Anodised aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, bottom and lock rail not less than 150 mm width anodised aluminum snap beading screws etc. complete all as specified.→

Supply & fix 200 mm length aluminium anodised barrel tower bolt extruded section complete all as specified and directed.

Supply & fix 250 mm long aluminium alloy, anodised sliding door bolt with haps, staple(bolt type) and fixing clip of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy complete all as specified and directed.

M&L 5.0 mm thick plain glass packing with rubber gasket, Al beading etc around both sides for fixing of glass all as specified and directed.

Taking down of unserviceable steel windows with frame (without taking down shutters and grill from frame) of size not exc 1.50 sqm each including cutting holes of appropriate size for insertion blocks of cement concrete hold fasts complete all as specified and directed.

S&F factory made box type steel window with pintle hinges & 2 Nos 150 mm mild steel tower bolts to each shutte, steel handle and with glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and shown on Grawing No CEJZ/TD-06/07 & CEJZ/TD-07/07

S&F factory made box type steel window with pintle hinges & 2 Nos 150 mm mild steel tower bolts to each shutte, steel handle and without glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and shown on Grawing No CEJZ/TD-06/07 & CEJZ/TD-07/07

M&L for 3.00 mm thick sheet glass, ordinary quality and glazing with oil putty in squares n. exc. 0.50 sqm in each pane complete all as specified and directed.

S&F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed.

Preparation of New steel surfaces of any description and in any position over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of redoxide primer.complete all as specified and directed.

Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balus ers; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165

Dismantling wrought iron or mild steel work of any description not otherwise provided for

S& F Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge

S& F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, post for trussed , column,channel or flat sections) including distance pieces, cleats etc

Excavating in post holes (or similar holes) each n exc 0.5 cu. M, getting out, returning, filling in and raming earth or broken , in layers not exceeding 25cm, watering, and removing surplus soil to a distance n exc 50m and making good surface

M/L Plain cement concrete (1:3:6) type C-2 using 40mm graded stone aggregate as in foundation, filling and mass concrete complete all as specified.

M& L for excavating over areas, n exc 1.5 m deep and getting out hard /dense soil

M& L for Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out hard /dense soil

Returning, filling including spreading leveling watering and well ramming in layers n. exc 25 cm in hard dense soil complete all as directed.

Removing excavated soil to a distance n. exc 50 m and depositing where directed at a level not exc 1.5 m above the starting point complete all as directed.

M&L PCC 1:4:8 (Type D2) using 40 mm graded stone aggregate as in foundation filling and mass concrete.

Material and labour rendering 15mm thick cement plaster in CM 1:4 on other than fair faces of brick/concrete work surfaces in two layer 10mm each layer and top layer mixed with integral water proofing compound all as per manufacturer's instruction including all necessary scafolding arrangments of any hieght and as specified. Note: (i) WPC shall be measured and paid for separately as 'Supply only'. (ii) WPC to be mixed @200ml per 50 Kg bag of cement all as manufacturers instruction.

Supply only liquid water proofing compound.

S& F Powder coated aluminium window and ventilator shutters, fix type,openable type or sliding type as site requirement side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified

Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer?in-charge. →

M& L for Sheet glass,5.00 mm thick ordinary quality and glazin with oil putty in square exc 0.5 sq. m in each pane s all as specified and directed.

M&L for Hard core, broken boulders/ stone to gauge n exc 63 m

Cement concrete (1.2.4) type B-1 using 20mm graded stone aggregate as in floor topping, 40mm thick, surfaces finished even and smooth without using extra cement complete all as specified.

M&L Glass dividing strips, 3 mm thick and 38 mm width complete all as specified and directed.

M/L 100 mm thick cement concrete type D-2, 1:4:8 for sub base all as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises.

M&L for machine cut kota stone slab flooring 20-25 mm thick over&including 15mm thick screed bed in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and mirror polishing complete .

M&L for non skid ceramic tiles 7 to 8 mm thick area of each tiles exc 0.11 sqm but n.exc 0.18 sqm (coloured tiles) in floor, set & jointed in neat cement slurry, pointed,in white or coloured cement to match, over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for glazed ceramic tiles coloured (350 x 250 x 7/450x350/300x450x7 to 8mm thick) on walls,incl highlighter tiles as if reqd set & jointed in neat cement slurry and pointed in white or coloured cement to match over and including rendering 10mm thick on wall with CM (1:4) complete all as specified and directed.

Taking down chowkats or frame with shutters ( without taking off shutter from frame ) n exc 1.50Sqm each.

Taking down chowkats or frame with shutters ( without taking off shutter from frame ) 1.50Sqm and n exc 4.0 Sqm each complete all as specified and directed.

Taking down shutter of any description exc 1 sqm but n.exc 2sqm each complete all as specified and directed.

M & L for Plain,Solid,Straight Chowkhats and frames wrought framed rebated on the solid rounded or chamfered put together with glue pinned at joints supplied and fixed 2nd class hard wood.

S&F 4 mm thick, sheet glass ordinary quality and glazing with oil putty/rubber packing/beading in square n exc 0.50 Sqm in each pane complete all as specified.

S&F Aluminium deco grills with opening of 5cm and 5mm thick with aluminium sheet frame complete all as specified.

Supply and fix solid PVC door frame of size 50 mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube supplying and fixing in opening as per specification complete all as specified and as directed by the Engineer-in-Charge

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail,lock rail & bottom rail on either side & as gap insert for top rail & bottom rail;Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification

Supply and fix 39 to 40mm thick flush shutters,solid core construction and both faces covered with decorative veneer wirh lipping/frame to match complete all as specified and as directed

S & F brass barrel tower bolts,stove enamelled black with bright bolt and fixed (150mm length of bolt)

S & F brass sliding door bolts,plate type,stove enamelled black with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts four on bolt plate and two on staple plate and fixed.(250mm length of bolt)

S & F butt hinges heavy weight cold rolled mild steel and fixed (100mm)

S & F brass handles, (150mm) complete all as specified.

M&L Providing precast/cast situ cement concrete 1:2:4 type B-1(using 20mm graded aggregate) in win- dow or door cills,lintels,etc complete all as specified.

M&L preparation of new surfaces of walls including cornices and applying two coats of oil bound distemper over a coat of primer, white or tinted over 1.5mm thick wall care putty all as specified & directed by the Engr-in-Charge.

M&L preparation new or previously untreated wood surfaces over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Taking down GI/PP-R tubing 15/20mm dia and connection including removable to store complete all as specified and directed.

Taking down GI/PP-R tubing 20/25mm dia and connection including removable to store complete all as specified and directed.

S&F 20mm & 25 mm outer dia, 3-layer PP-R Polypropylene random copolymer) pipes SDR 7.4 & SDR 11 UV stablised and antimicrobial welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc. all as specified

Supply and fix in repair vitreous china ware wash hand basin 550mm x 400 mm size flat back or angle including new bracket and making good all connections in repairs complete all as directed by the Engr-in-Charge.

S&F 32mm Dia PVC waste pipe for sinks or wash basines etc,. in repairs complete all as directed by the Engr-in-Charge.

Supply and fix 32 mm dia bore waste fittings brass chromium plated fixed to wash hand basin/urinals with long screwed shanks and fly nuts flange and bedded in run lead cement and other end fixed in repairs complete all as directed by the Engr-in-Charge.

S&F in repair 15 mm bore piller cocks mixer fancy type,cast copper alloy,with capstan heads,chromium plated,screwed down, fancy type high pressure, with or without lettred 'HOT and COLD' with long screwed sunk and fly nuts.

S&F repair Bib taps, cast copper alloy, chromium plated, fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule 15mm dia and fixed

S&F 15mm bore angle valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed in repair.

Supply and fix PVC connection15 mm bore LDPE pipe 45cm long with brass nuts and washers on both ends all as in repairs specified and directed.

S&F in repairs rim less syphonic vaccume western floor mounted water closet pan (Single piece suit),of size 740x350x660mm white incl seat cover as per manufacturers specification complete all as specified and directed. Make:Parryware cat part No:C8901/C8902 or equivalent as approved by GE

S&F in repair Towel Rail 600mm long 20mm dia,D type cromium plated, fixed with and including Chromium plated brass screws and wooden/plastic cleats. and fixed in repairs all as specified and directed.

S&F sheet glass shelf assembly consisting of 5.5 mm thick sheet galss shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long

S &F 75 mm dia PVC (SWR) floor trap plain with grating doom with or without hole as directed including jointing to waste pipe fixed in solvent cement or cement concrete 1:2:4 type B1 all as specified and directed.

Demolition/Dismantling of drain pipes any type at any position complete all as specified and directed.

S &F 75mm bore PVC(SWR) Pipes single socketed in any length with rubber ring joints laid in trenches or in floor all as specified and directed.

S &F 110mm bore PVC(SWR) Pipes sinle socketed in any length with rubber ring joints laid in trenches or in floor all as specified and directed.

S &F 75mm bore PVC(SWR) bend all as specified and directed.

S &F110mm bore PVC(SWR) bend all as specified and directed.

S&F 110mm PVC (SWR) junction single, (Single T) equal or unequal

S&F 75mm PVC (SWR) junction single, (Single T) equal or unequal

S&F in repair PVC (SWR) vent cowl of 75mm bore complete all as specified and directed.

Taking down carefully copper/ aluminium point wiring (light, fan, buzzer, socket or power) complete including fixture and fittings such as switches, ceilling roses, pendants , regulators, sockets light fitting etc for taking credit removing from site and making good disturbed surface etc.

Material and labour for point wiring with 1.5 sqmm cable FRLS PVC insulated, unsheathed copper multistranded conductor, 1100 V grade of size 1.5 sqmm including necessary termination board 1.5 Sqmm PVC insulated unsheathed FRLS copper conductor as earthing and connected to common earthing with PVC heavy duty casing caping/PVC conduit ISI marked as rquired at site along with all accessories and making good the disturbed surfaces of wall/ ceiling etc for the following : -

One light point/ one fan point/ Bell Point controlled by one switch

One 3 pin socket outlet, 5 Amp independent

Supply switch piano flush type single pole one way 5 Amps all as specified

Supply switch socket combination multi purpose, 5 amp all as specified

S & F Ceiling rose 3 plates flush type 6 Amps,250 volts AC ISI marked

All as per item No 2 above but for point wiring for power point with 2.5 Sqmm FRLS PVC insulated unsheathed copper cable 1100 Volt grade drawn through and including PVC casing caping heavy duty ISI marked /heavy duty conduit ISI marked as required at site alongwith accessories with 2.5 Sq mm FRLS PVC insulated unsheathed copper conductor cable as earthing and connected to common earth all as specified.

S & F switch socket combination switch socket outlet 3 pin, 16 amp flush type

S&F wall mounted LED light fitting 1x20 watts AC decorative box type with driver holder including LED tube light , energy efficient type 4 feet long including neccessary conection prewired and making connection with 3 core copper flexible cable of appropriate size from ceilling rose.

S&F warm white/ white LED luminaire 600X600 mm,35/36 watt,220V recessed type lumen output >= 122 lumen per watts , THD < 10% environmental friendly , new generation , aesthetically designed , ultra modern with high brightness SMD LEDs as light source incl inbuilt drivers with high efficiency PMMA diffuser soft glare free light complete suitable for roof ceiling including connecting up with three core flexible copper conductor of suitable size all as specified and directed.

S&F LED security light fitting 35 watts 230 volts AC outdoor type with high pressure die cast aluminium housing and heat resistant complete with driver,lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete.

M&L for Distribution board double door made out of sheet metal enclosure (CRCA sheet) dust and vermin proof TPN 4 way with 200 Amps rated copper bus bar neutral bar, earth bar IP 43 protection, triple pole and neutral 415 volts, flush to wall / fixed on surface complete all as specified and directed incl taking down old one. (Make :- Legrand/Havells/L&T/Schnider)

Supply and fix sheet metal enclosure SPN DB 12 way,single phase 240 volts double door with 200 amp rated bus bar complete all as directed.

Supply and fix for miniature Circuit breaker (MCB) single pole and current carrying caoacity 5 to 32 Amp 240 volt 'C' curve 10 KA in the MCB DB with connection testing and commissioning complete all as specified and directed.

Supply and fix for miniature Circuit breaker (MCB) single pole & neutral 240 volt C curve 10 KA 32 Amps capacity IP 20 in the MCB DB with connection testing and commissioning complete all as specified and directed.

Supply and fix for miniature Circuit breaker (MCB) triple pole & neutral 415 volt C curve 10 KA, 63 Amps capacity IP 20 in the MCB DB with connection testing and commissioning complete all as specified and directed.

S&F two single core 6 sq mm for Sub Main wiring with copper conductor multistranded PVC insulated and unsheathed 1100 Volts grade in and including PVC casing capping/ pvc conduit with fixing accessories including one run of 6 Sq mm copper conductor. (Note - Two runs of 6 Sq mm cable, one run of 6 Sq mm earth cable and one run of PVC casing Capping shall be measured as one running meter.)

Excavation in trenches not exc 1.5 m wide and not exc 1.5 m in depth and getting it out for laying of cable / pole etc in hard/dense soil all as specified.

Returning, filling in, including spreading, leveling watering, and well ramming in layers not exc 25 cm in hard/dense soil all as directed.

Removing excavated material n.exc 50m and depositing where directed at a level exc. 1.5 cm above the starting point all as directed.

Sand cushioning with clean dry sand to cables with layer of sand 8cm before laying of cable and 15cm thick after laying of cable complete all as specified and directed. Note :- For payment purpose punned thickness of 18cm shall be measured against spread thickness of 23 cm as mentioned in para 19.75 of SSR part-I.

Supplying and laying unreinforced precast concrete cable cover, class LV, type 1 flat of size 250mm x150mm x 40mm placed perpendicular of the cable complete.

Supply laying and testing cable XLPE insulated screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables heavy duty 1100 volts grade with stranded aluminium conductor of size 35 sqmm 3.5 core.

Material and labour earthing complete with galvanized steel earth plate 60 cm x 60cm x 6.0mm thick buried directly in ground vertically to a depth not less than 2.25 mtr below ground level with top edge of the earth plate at a depth not less less than 1.5 mtr filled around with 15 cm thick alternate layers of charcoal dust and salt and connected to earth lead wire 4mm dia (8 SWG) by means of bolt, nut and check nuts and washers of galvanized iron or steel and thimble and other ends of the earth wire connected to main switch board and protected by galvanized iron pipe light grade 15mm bore and watering pipe 20mm dia light grade with funnel and wire mesh, pcc 1:3:6 type C-1 in chambers RCC 1:2:4 type B-1 in pit cover reinforced with 8 mm dia deformed bars 15cm center to center both ways all as directed by Engr-In-Charge, complete all as shown in electric plate No 3 of MES SSR Part I

Supply and fixing One bell/ Buzzer point controlled by one push button on the same board with other switches or independent with cable 1.5sqmm size all as specified

S & F Ceiling rose 3 plates flush type 6 Amps,250 volts AC ISI marked

Supply and fix sheet metal enclosure SPN DB 08 way,single phase 240 volts double door with 200 amp rated bus bar complete all as directed.

Supply and fix in repair sheet metal enclosure SPN DB 08 way,single phase 240 volts double door with 200 amp rated bus bar complete all as directed.

M&L for stone dust sand cushioning to UG cable laid in trenches all as specified and directed.

Supply laying and testing cable XLPE insulated screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables heavy duty 1100 volts grade with stranded aluminium conductor of size 16 sqmm 2 core.

S & F lamp holder PVC/polycarbonate type with back plate suitable for batten fittings complete all as specified.

Deduct Credit for Demolished/Dismantled material Rs (-) 62,017.82 (Minus) as listed in Schedule 'A' Part-II (Credit Schedule) Note : Tenderers will not quote against this item being a tentative amount, to be considered to arrive at the 'Contract Sum'.

M/S ALI MOHD AND SONS (BID ID -3394139)

M/S MOHD FAROOQ (BID ID -3394224)

M/S MOHD KHAN (BID ID -3394533)

M/S RW INFRA (BID ID -3394306)

KASHMIR FAIR DEAL SERVICES (BID ID -3394453)

M/S M A ENTERPRISES (BID ID -3394685)