CA NO.CWE BLY/GE (W)/126 OF 2025- 2026SPECIAL REPAIR TO CUPBORAD SHUTTERS FRAMES PARTITIONS SHELVES ETC IN MD ACCN OF MAP OF JRC UNDER GE (WEST) BAREILLY

Taking down chowkats with shutters (without taking off shutters from the frames) area not exc 1.5 Sqm each including making good disturbed portions of wall with new or old bricks, lintel,cills, etc in CM 1:4 or cement concrete 1:2:4 type B0 (using 12.5 mm graded stone complete all as specified and directed.

Taking down chowkats with shutters (without taking off shutters from the frames) area exc 1.5 Sqm each and not exc 4.00 sqm including making good disturbed portions of wall with new or old bricks, lintel,cills, etc in CM 1:4 or cement concrete 1:2:4 type B0 (using 12.5 mm graded stone complete all as specified and directed.

S&F factory made PVC Cupboard frame of the size 75mm x 40mm with a wall thickness of 5mm, made out of extruded 5mm thick plain/prelam PVC sheet of density 600 kg/cbm, having bottom width of 50mm and thickness of 10mm. All four frame lengths reinforced with 15 mm x 15mm M. S. square tubes of 19 gauge thickness throughout the frame and mitre cut at two corners adjointed with 2 nos. of 15mm long brackets of 10mm x10mm M S square tubes. The door frame shall be fixed to the wall using 8/100 long M S screws through the frame by using PVC fasteners. A minimum of 4 nos. of screws to be provided for each vertical member and minimum of 2nos. of screws to be provided horizontal member etc. complete as per direction of Engr-in-Charge, manufacturer's specification and drawing.

S&F factory made PVC cupboard flush type shutter of 30mm thick consisting of frame made out M S tubes of 19 gauge thickness and size 19mm x 19mm for stiles and rails. The inside panel shall consist of 20 mm thick multichamber hollow PVC section of 1mm wall thickness, bonded using solvent cement/ cynoacrylate adhesive with 5mm thick plain/ prelam PVC sheet, on both side of inside panel incliding necessary items to fix the shuter to frame such as 100mm stailess steel hinges, 100 mm long handles made of anodised aluminium and magnetic ball catch for each pair of shutter.All four edges of the panel to be sealed with lipping of 10mm thick and 20mm wide PVC sheet baton (made by sticking 2nos. PVC foam sheet of 5mm thickness using PVC solvent cement adhesive). complete as per direction of Engr-in-Charge.

S&F for 6 mm thick solid PVC sheet, one side prelaminated and other plain white lamination, fixed on back side of wall and sides of cup board with SS fastners complete all as specified and directed.

S&F for 18 mm thick solid PVC board, both side prelaminated, one side with decorative choice lamination, and other side plain rigid white lamination as in cupboard shelves & partitions including powder coated aluminium cleat (colour of powder coated to match colour / shade of laminate) and as in fixing to sides of cupboard, soffits & base of cupboard with SS fastner also including PVC lipping on all exposed edges of same texture & shade to match the laminate complete all as specified as directed. (Note: 1. Design & layout of wardrobe and pattern / colour of lamination to be approved by GE. 2. Thickness of laminated not less than 1mm for inside plain white type. The laminate shall be fixed to base with approved adhesive as per manufacturer's instructions and machine pressed to ensure proper bonding with base ply and avoid air pockets.)

S&F 100 mm long stainless steel hinges, medium weight complete all as specified and directed.

S&F fancy type 200 mm long stainless steel handles etc, complete all as specified and directed.

S&F 125 mm long hasp and staple, mild steel, wire type, stove enamelled black, including bolt to hinge plate and fixed with screws complete all as specified and directed.

M&L for 12 mm thick rendering on fair faces of brick work or concrete surfaces in cement mortar 1:6 finished even and smooth without using extra cement including applying two coats of OBD over a coat of putty complete all as specified and directed

M&L for rendering 5mm thick on ceiling or concrete surfaces in cement mortar (1:3) finished including taking down plaster the surface even and smooth without using extra cement and necessary scaffolding and applying two coats of white wash complete all as specified and directed.

M&L for rendering 5mm thick on ceiling or concrete surfaces in cement mortar (1:3) newly surface even and smooth without using extra cement and necessary scaffolding and applying two coats of white wash complete all as specified and directed.

M&L for form work to edges of concrete flats, treads, breaks in floors window cill, concrete railing opening in conc wall, floor and roof n.exc 20cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10 cm but n.exc 20cm wide for rough finished surfaces of concrete complete all as specified and directed.

M&L for form work to chullah hoods, chajjas, trough and similar works including edges complete all as specified and directed.

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M&L for RCC 1:2:4 type B1 (using 20 mm graded stone aggregate) as in slab, shelves and stair case, beams etc. including demolition of reinforced cement concrete (other than ground floors), shelves, slabs and stair case similar work carefully and matchin to adjoining disturbed surfaces at any position complete all as specified and directed.

Please Enable Macros to View BoQ information