Development of Green Park and Play Ground in Golf Ground under Dhanbad Municipal Corporation, Dhanbad

Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring andstrutting etc. complete. (Lift up to 1.5 m.)5.1.1

Supplying hard murum/ kankar at the road site, including conveying and stacking complete and Spreading hard murum/ soft murrum/ gravel or kankar for side width complete. Compacting the hard murum side widths including laying in layers on each side with vibratory roller including artificial watering etc. complete.DSR-16.3.10

150mm thk.compacted hard murum with proctor density 95% filling in ground with contractors material / brought from outside and approved by engineer in charge in layers of 15 cm to 20 cm including watering and compaction etc. complete. compacted hard murum with proctor density 95%DSR-16.2

Construction of granular sub-base by providing close gradedMaterial,mixinginamechanicalmixplantatOMC, carriageofmixedMaterial toworksite,spreadinginuniform layers with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per clause 401. Rate per cum for grading-III MaterialSOR-4.01 (A)

Providing, laying, spreading and compacting graded stone aggregate (size range 53 mm to 0.075 mm ) to wet mix macadam (WMM) specification including premixing the material with water at OMC in mechanical mix plant, carriage of mixed material by tipper to site, for all leads & lifts, laying in uniform layers with mechanical paver finisher in sub- base / base course on well prepared surface and compacting with vibratory roller of 8 to 10 tonne capacity to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge.-2 layersSOR-4.14

Providing and applying primer coat with bitumen emulsion on prepared surface of granular base including clearing of road surface and spraying primer at the rate of 0.75 kg/sqmt using mechanical/manual means and as per relevant clause of section 502SOR-5.01(I)

Providing and laying bituminous macadam with using crushed stone aggregates of specified grading premixed with bituminous binder, transported to site ,laid over a previously prepared surface with paver finisher with electronic sensor to be required grade, level and alignment and rolled with smooth wheeled, vibratory and tandem rollers as per specification to achieve the desired compaction and density, complete as per specifications and directions of Engineer in charge.SOR-5.03 (ii)

Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type A and B Seal coatsSOR 5.09

Providing and laying Bituminous concrete using crushed stone aggregates of specified grading, premixed with bituminous binder and filler, transporting the hot mix to work site by tippers, laying with paver finisher equipped with electronic sensor to the required grade, level and alignment and rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction and density as per specification, complete and as per directions of Engineer-in-Charge.40/50 mm compacted thickness with bitumen of grade VG-30 @ 5.5% (percentage by weight of total mix) and lime filler @ 3% (percentage by weight of Aggregate) and waste plastic additive @ 8% (percentage by weight of bitumen) .SOR-5.05

Providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.20 kg per sqm on the prepared bituminous surface cleaned with mechanical broom.Sor-5.02 (i)

Supply and installation of PayFlex EPDM rubberized flooring in inset form with top layer of 9mm 100% EPDM (Ethylene Propylene Die monomer) and bottom layer of 15mm Styrene-Butadiene Rubber (SBR). The EPDM granules ranging from 1mm to 4mm should have granules distribution such as <1mm – 2%, <2mm ->1mm – 10-20%, <3mm- >2mm – 30-40%, <4mm->3mm – 38-48% >4mm – 3%. The EPDM granules should have specific gravity – 1.5+/-0.0, Hardness (Shore A) – 62-67, Density – 700- 730 kg/cu.mtr, Tensile strength > 4.0 MPa, Elongation @ BREAK > 400% and curing system – Peroxide cured. The SBR granules should be primarily in the range of 1-4mm size and to be used primarily to create cushion effect. PU binder quality should be from company like BASF for insitu application to be done. The flooring work should have material defects warranty of 5 years.MR

Cement lead 3 km

Sand lead 35 km

Stone chips lead 17 km

Stone METAL

Emulsion

BITUMEN

Ploughing the existing ground to a depth of 15 cm to 25 cm and watering the same2.29

Fine dressing of the groundDSR -2.7

Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50 m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift up to 1.5 m.)BCD-5.1.1

Supplying hard murum/ kankar at the road site, including conveying and stacking complete and Spreading hard murum/ soft murrum/ gravel or kankar for side width complete. Compacting the hard murum side widths including laying in layers on each side with vibratory roller including artificial watering etc. complete.DSR-16.3.10

Supplying and stacking of good earth at site including royalty and carriage up to 5 km lead complete (earth measured in stacks will be reduced by 20% for payment).HORTICULTURE DSR 2.2

Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50 m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift up to 1.5 m.) By Mechanical MeansBCD 5.1.1

150mm THK.COMPACTED HARD MURUM WITH PROCTOR DENSITY 95% Filling in ground with Contractors material / brought from outside and approved by Engineer in charge in layers of 15 cm to 20 cm including watering and compaction etc. complete. COMPACTED HARD MURUM WITH PROCTOR DENSITY 95%DSR 16.

Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer- in-Charge.- With material conforming to Grade-III (size range 75 mm to 0.075 mm) having CBR Value-30 Rate per cum for grading-III MaterialSOR-4.01

Providing, laying, spreading and compacting graded stone aggregate (size range 53 mm to 0.075 mm ) to wet mix macadam (WMM) specification including premixing the material with water at OMC in mechanical mix plant, carriage of mixed material by tipper to site, for all leads & lifts, laying in uniform layers with mechanical paver finisher in sub- base / base course on well prepared surface and compacting with vibratory roller of 8 to 10 tonne capacity to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge.-2 layersSOR-4.14

Providing and applying primer coat with bitumen emulsion on prepared surface of granular base including clearing of road surface and spraying primer at the rate of 0.75 kg/sqmt using mechanical/manual means and as per relevant clause of section- 502SOR-5.01

Providing and laying bituminous macadam with hot mix plant using crushed aggregates of specified grading premixed with bituminous binder, transported to site ,laid over a previously prepared surface with mechanical paver finisher to required grade, level and alignment and rolled as per clauses 501.6 and 501.7 to achieve the desired compaction comple

te in all respects and as per relevant clauses of section-504SOR-5.03

Providing and laying semi- dense Bituminous concrete using crushed stone aggregates of specified grading, premixed with bituminous binder and filler, transporting the hot mix to work site by tippers, laying with paver finisher equipped with electronic sensor to the required grade, level and alignment and rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction and density as per specification, complete and as per directions of Engineer-in- Charge.25 mm compacted thickness with bitumen of grade VG- 30 @ 5% (percentage by weight of total mix) and lime filler @ 2% (percentage by weight of Aggregate) prepared in Drum Type Hot Mix Plant of 60-90 TPH capacity.SOR-5.05

Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type A or B seal coats as per relevantsor-5.09

Providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.20 kg per sqm on the prepared bituminous surface cleaned with mechanical broom.Sor-5.02 (i)

Supply & installation of approved brand /make/manufacturer Cast aluminium alloy with green / Black powder coated finish Tennis post including post caps, gear housings, flush mounted ,removable handle, jam-free cable tensioning hardware system & superior hardened gears case and ground sleeves, and 42' long Tennis Net consist of 3mm High Tensile Braided Twine and black/white PVC Banding 2 1/2" on net Side & Bottom Headline Cable - 6mm PVC Coated Steel Cable with Loop & Pin Finish etc complete as per the direction of EngineerMR

TENNIS AND MULTISPORTS FENCING: Supply and installation of approved brand /make/manufacturer welded Mesh Fencing system with H post mounted on Base Plate: 10 Feet High system (2 panels of 5 feet high); Mesh Size: 50mmx200mm; Wire Dia: 4.5mm; Galvanized and Green Powder Coated, cost included single leaf swing gate with Mesh Infill and Sq. post mounted on Base Plate: Height: 7feet; width: 2.4 mtr; and additional 10 feet H-posts mounted on Base plate with accessories required to accommodate 4 corners and 2 gates, and 3 feet x 2.5 mtr panel required to be mounted above gates etc complete & as directed byMR

Cement lead 3 km

Sand lead 35 km

Stone chips lead 17 km

Stone METAL

Emulsion

BITUMEN

MULTISPORTS FLOORING: Supply and installation of Bergo Multi-sports Interlocking modular PP tiles or equivalent having material composition of environmentally friendly recyclable UV- stabilized 100% polypropylene with ISO 2076standards. Each tile should have thickness of 14.1mm (EN 428 standards), size of 303.3mm*303.3mm (EN427 standards), weight of 0.356kg (EN 430 standards), slip resistance of 108 PTV (EN13036-4), Impact resistance of 20kJ/sqm, shock absorption of 6% (EN14808), vertical deformation of 0.3mm (EN14809), vertical ball behaviour of 98% (EN12235), resistance to wear of 0.1g/1000cycles (EN ISO 54701). The flooring work should have material defectsMR

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead up to 50 m and lift up to 1.5 m, as directed by

Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5m.2.28

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete5.1.10

Excavating, supplying and filling of local earth (including royalty) by mechanical transport up to a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundationDSR 2.25a

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work up to plinth level :BCD-5.3.1.5

1:2:4 (1 Cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 40 mm nominal size)Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:Cement mortar 1:4 (1 cement : 4 coarse sand)BCD-5.3.1.3

12 mm cement plaster of mix 1:4 (1 cement : 4 fine sand)BCD-5.7.2

Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade New work (Two or more coats applied @ 1.43 litre/ 10 sqm. Over and including priming coat of exterior (Company13.48A.1

Supply and installation of Ebaco turf with pile height of 13mm thickness and width 4m. Colour - Emerald Green. Yarn should have PE composition, monofilament curl structure, PE8000 DTEX, 165μm±15μm Tape thickness, 0.8 1.0mm Tape width. The carpet should have Pile height 13mm±1mm, Gauge 3/16 inch, Stitches per 10cm 34±1, Stitches per m2 71400 ±100, Total yarn weight 1861g/sqm ±10%. The backing system should have Primary backing PP + polyester fibber short-staple + Mesh scrim inlay, Weight 255 g/sqm, Secondary backing Latex, Total carpet weight should be 3266g/sqm ±100g.NS

Cement lead 3 km

Sand lead 35 km

Stone chips lead 17 km

Supply and installation of Cricket practice net of size 80 feet long x 12 feet wide x 12 feet high x 2 cricket Cage fabricated with 60 OD X 3 mm thick GI post at distance 10 feet c/c with 30 mm x 30 mm X 2.5 mm thick polypropylene barware make Net etc complete & asNS

Extra for earthwork in hard soil as per specification and direction of E/I (Vide classification of soil item -B)JH_BCD_2022_5.1.2

Earth work in excavation in foundation trenches - do - all complete as per building specification and direction of E/I.JH_BCD_2022_5.1.1

Providing designation 75 B one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/l.JH_BCD_2022_5.6.3

Providing coarse clean sand in filling in foundation trenches -do - all complete as per building specification and direction of E/I (Mode of measurement compacted volume)JH _BCD_2022_5.1.10

Providing R.C.C (1:1.5:3) in foundation -do - all complete as per building specification and direction of E/IJH _BCD_2022_5.3.9.1

Providing 12 mm thick cement plaster (1:4) -do- all complete as per building specification and direction of E/I.JH_BCD_BCD_5.7.2

Providing 1.5 mm cement punning including screening curing with all leads and lifts of water ,scaffolding taxes and royalty all complete as per building specification and direction of E/I.JH_BCD_2022_5.7.11

Providing TMT steel reinforcement - do - all complete as per building specification and direction of E/I.JH_BCD_2022_5.5.5(A)

Cement lead 3 km

Sand lead 35 km

Stone chips lead 17 km

Centring and shuttering including strutting , propping etc. and removal of form for foundation , footing , bases of columns, etc for mass concrete.JH_BCD_2022_5.3.17.1

Bricks lead 8 km

Steel lead 3 km

Excavation in Soil using Hydraulic Excavator CK 90 and Tippers with disposal up to 50 metres. (Excavation for roadwork in soil with hydraulic excavator of0.9 cum bucket capacity including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross sections, and transporting to the embankment location within all lifts and lead up to 1000m).5.1.1

Construction of Subgrade and Earthen Shoulders (Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts & - leads, transporting to site, spreading, grading to required slope and impacted to meet requirement of table No. 300-2). Rcd 3.18

Construction of granular sub-base by providing close gradedMaterial,mixinginamechanicalmixplantatOMC, carriageofmixedMaterial toworksite,spreadinginuniform layers wi

th motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per clause 401. Rate per cum for grading-III Materialsor-4.01(A)

TENNIS AND MULTISPORTS FENCING: Supply and installation of approved brand /make/manufacturer welded Mesh Fencing system with H post mounted on Base Plate: 10 Feet High system (2 panels of 5 feet high); Mesh Size: 50mmx200mm; Wire Dia: 4.5mm; Galvanized and Green Powder Coated, cost included single leaf swing gate with Mesh Infill and Sq. post mounted on Base Plate: Height: 7feet; width: 2.4 mtr; and additional 10 feet H-posts mounted on Base plate with accessories required to accommodate 4 corners and 2 gates, and 3 feet x 2.5 mtr panel required to be mounted above gates etc complete & as directed byMR

Cement lead 3 km

Sand lead 35 km

Stone chips lead 17 km

Stone METAL

Cement Concrete Pavement (Construction of un-reinforced, dowel jointed, plain cement concrete pavement over a prepared sub base with 43 grade cement @ 400 kg per cum, coarse and fine aggregate conforming to IS 383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a batching and mixing plant as per approved mix design, transported to site, laid with a fixed form or slip form paver, spread, compacted and finished in a continuous operation including provision of contraction, expansion, construction and longitudinal joints, joint filler, separation membrane, sealant primer, joint sealant, bonding strip, dowel bar, tie rod, admixtures as approved, curing compound, finishing to lines and grades as per drawing) 6.2 RCDRcd-6.2

Extra for earthwork in hard soil as per specification and direction of E/I (Vide classification of soil item -B)JH_BCD_2022_5.1.2

AND MULTISPORTS FENCING: Supply and installation of approved brand /make/manufacturer welded Mesh Fencing system with H post mounted on Base Plate: 10 Feet High system (2 panels of 5 feet high); Mesh Size: 50mmx200mm; Wire Dia: 4.5mm; Galvanized and Green Powder Coated, cost included single leaf swing gate with Mesh Infill and Sq. post mounted on Base Plate: Height: 7feet; width: 2.4 mtr; and additional 10 feet H-posts mounted on Base plate with accessories required to accommodate 4 corners and 2 gates, and 3 feet x 2.5 mtr panel required to be mounted above gates etc complete & as directed byMR

Earth work in excavation in foundation trenches - do - all complete as per building specification and direction of E/I.5.1.1

Filling in foundation trenches and plinth - do - all complete as per building specification and direction of E/l (Mode of measurement compacted volume)5.1.7

Providing coarse clean sand in filling in foundation trenches -do - all complete as per building specification and direction of E/I (Mode of measurement compacted volume)5.1.10

Providing designation 75 B one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/l.5.6.3

Providing P.C.C (1:3:6) in foundation -do - all complete as per building specification and direction of E/I5.3.1.5

Providing R.C.C (1:1.5:3) in band at plinth -do - all complete as per building specification and direction of E/IJH _BCD_2022_5.3.9.1

Constructionofun-reinforced,dowel jointed,plaincement concrete pavement over a prepared sub base with approvegradecement@400kgper cum, coarse and fineaggregateconforming to IS383,maximumsizeof coarse aggregate not exceeding 25mm, mixed in a batchingandmixingplant asper approvedmixdesign, transported to site, laid with a fixed former slip form paver, spread, compacted and finished in continuous operation includingprovisionof contraction, expansion, construction and longitudinal joints, joint filler, separation membrane,sealantprimer, jointsealant,debondingstrip, dowel bar, tie rod, admixtures as approved, curing compound, finishing to lines and grades as per drawing

Providing and laying in position cement concrete of specified grade excluding the cost centring and shuttering - All work up to plinth level: (1:1.5:3) in foundation -do - all complete as per building specification and direction of E/I5.3.9.1

Providing 12 mm thick cement plaster (1:6) -do- all complete as per building specification and direction of E/I.JH_BCD_2022_5.7.3

Providing two coats of plastic emulsion paint of approved shade and make over a coat of cement primer over new surface including preparing plastered surface by rubbing smooth with pumice stone or fine sand paper, applying putty wherever required, scaffolding washing of floor and taxes all complete as per building specification and direction of E/l.JH_BCD_2022_5.8.21

Providing designation 75 B brick work in C.M. (1:6) in superstructure - do-as per specification and direction of E/I.JH _BCD_2022_5.2.14

Providing designation 75 B brick work in C.M. (1:6) in superstructure - do-as per specification and direction of E/I.JH _BCD_2022_5.2.14

Providing designation 75 B brick work in C.M. (1:6) in superstructure - do-as per specification and direction of E/I.JH _BCD_2022_5.2.14

Providing designation 75 B brick work in C.M. (1:6) in superstructure - do-as per specification and direction of E/I.JH _BCD_2022_5.2.14

Providing designation 75 B brick work in C.M. (1:6) in superstructure - do-as per specification and direction of E/I.JH _BCD_2022_5.2.14

Providing designation 75 B brick work in C.M. (1:6) in superstructure - do-as per specification and direction of E/I.JH _BCD_2022_5.2.14

Centring and shuttering including strutting , propping etc. and removal of form for Lintels, beams , plinth beams, girders, bressummers and cantilever.JH BCD_2022_5.3.17.5

Steel work welded in built up sections/framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required, all completeDSR 10.25.1

Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 1.00 mm thick with zinc coating not less than 275 gm/m²DSR 12.01.01

Providing two coats of painting with ready mix paint of approved shed and makeover steel surface including cleaning the surface thoroughly scafollinding and taxes all after removing dirt including scales smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specification and direction of E/I.0.214386574074074

Providing and laying vitrified tiles in different size thickness to be specified by manufacture with water absorption less then .08% and conforming to IS 15662,of approved make ,in all colours & shade ,in skirting ,riser of steps ,over 12 mm thick bed of cement mortar (1:3) (1 cement : 3 coarse sand ) jointing with white cement slurry 3.3 kg /sqm including grouting the joint with white cement matching pigmentJH 5.6.28

Centring and shuttering including strutting , propping etc. and removal of form for columns, pillars, piers, Abutments, posts and struts.5.3.17.6

Cement lead 3 km

Sand lead 35 km

Stone chips lead 17 km

Providing TMT steel reinforcement - do - all complete as per building specification and direction of E/I.5.5.5(a)

Centring and shuttering including strutting , propping etc. and removal of form for foundation , footing , bases of columns, etc for mass concrete.JH_BCD_2022_5.3.17.1

Bricks lead 8 km

Supply & installation of approved brand /make/manufacturer Cast aluminium alloy with green / Black powder coated finish Tennis post including post caps, gear housings, flush mounted ,removable handle, jam-free cable tensioning hardware system & superior hardened gears case and ground sleeves, and 42' long Tennis Net consist of 3mm High Tensile Braided Twine and black/white PVC Banding 2 1/2" on net Side & Bottom Headline Cable - 6mm PVC Coated Steel Cable with Loop & Pin Finish etc complete as per the direction of Engineer

Stone Metal lead 23 km

Fabrication, Supply, Erection, Testing and Commissioning of 20 Mtrs Lighting high mast including head frame height fabricated as per attached specifications suitable to fix 16 nos. of 500 W luminaries, Lightening Arrestor, Double dome LED type aviation obstruction light and Earthing Spikes in Football ground, suitable for Wind Velocity of 50 Mtrs/Sec. The mast shall be provided with safety caged ladder with necessary ladder. Total weight of the high mast including head frame weight and caged ladder shall be minimum 1900 KG. The complete system shall be supplied with necessary accessories like foundation bolts, anchor plates etc.MR

ITC of the high mast and light fixture with the help of suitable tools and plants, wiring of luminaries with all wiring material like PVC insulated PVC sheathed flexible cable of suitable copper conductor lugs. and all labour & construction of foundation MR

System Wattage: 500 Watts, Minimum Luminous Efficacy : 130 Lumen/watt, IP 66, SPD(Internal):4KV, SPD(External):10KV, minimum CRI>70, having protective toughened glass with 5 year warranty.MR

EPR insulated / PVC sheathed copper conductor 5C x 2.5 sqmm cu flexible cableM1547

Supply and fixing of Terminal panel box with MCB SP 6-32A- 16 nos. and 32A DP MCB-2 nos. including all wiring as requiredMR

High Mast Lighting Control Panel with Dimming control / Lighting control gateway:(DALI-2/DMX512)MR

Earthing with GI earth plate 600mmx600mmx6mm including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal and salt as requiredJSOR 3.4

Providing & fixing 25mmx5mm GI strip at in 40mm dia GI pipe from earth electrode including connection GI nut bolt spring washer excavation and refilling as requiredJSOR 3.9

Earthing with Copper earth plate 600mm x 600mm x 3mm including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal and salt as requiredJSOR

Providing & fixing 25mmx5mm Cu strip at in 40mm dia GI pipe from earth electrode including connection brass nut bolt spring washer excavation and refilling as requiredJSOR 3.11

Supply and laying 8 SWG copper wire at 0.5m below ground levelJSOR 3.7

11 Mtr. height Octagonal Hot - Dip galvanized pole (BOP - 1133) with top dia 90 mm, bottom dia 240 mm & made of 3 mm thick sheet, base plate dimensions 320 X 320 X 16 mm ( L x B x T) including suitable sizes of foundation bolt all complete as reqd. (Without Arm) (Basic Rate: Rs.17,300.00 + overhead & profit @ 14.95% = Rs.19,886.35)M749

1m Double Arm suitable for 90mm top (Basic Rate Rs. 2490.00 + Overheads & Profit @ 14.95% = 2862.25)M757

Installation Testing and Commissioning of 9 Mtr. Octagonal pole and Light fitting with the help of suitable too land plants and construction of shallow foundation with M25 grade concrete considering safe soil bearing capacity of 10T/mtrs sq. but excluding wire and MCB. (Basic Rate Rs 9200+ Overheads & Profit @ 14.95% = Rs.)M877

240 W Flood light fitting .9.2.8

3 x 2.5sqmm cu flexible cable (Basic Rate Rs130.00 + Overheads & Profit @ 14.95% = Rs.149.43)M1907

SITC of Terminal panel box with MCB SP 6-32A- 2 nos & 32A DP MCB-1 nos.MR

Outdoor stand mounted Feeder Panel with 63A TP&N, MCB incomer, 63 amp TP contactor automatic switching of luminaires, Power tool control incomer outgoing terminal etc. as required (for high mast) (Basic Rate: 27,800.00+Over Head & [email protected]% = Rs. 31,956.00 )M-1546

SITC 200 W Flood light fitting.9.2.7

Supplying and drawing following size of FR PVC insulated copper conductor 2x1.5 sqmm + 1x1.5sqmm cable in PVC conduit 1.7.1

Supply of XLPE insulated sheathed (heavy duty) armoured electric cables with Aluminium conductor for working voltage 1100 volts conforming to IS:7098 (part-1)/IS:1554; 2 core x16 sq mm (Basic Rate: Rs. 164.00 + Overhead & Profit @ 14.95% = Rs. 188.52)M-738

Supply of XLPE insulated sheathed (heavy duty) armoured electric cables with Aluminium conductor for working voltage 1100 volts conforming to IS:7098 (part-1)/IS:1554; 2 core x10 sq mm (Basic Rate: Rs. 138.00 + Overhead & Profit @ 14.95% = Rs. 158.63)M-737

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of size not exceeding 35 sq mm direct in ground including excavation and refilling the trench etc. as required but excluding sand cushioning and protective covering 5.17

Supplying and laying of 40mm dia medium class GI pipes for road crossing (Basic Rate: Rs. 300.00 + Overhead & Profit @ 14.95% = Rs. 344.85)M-930

Supplying and laying 6 SWG GI wire at 0.50 meter below ground level for conductor earth electrode, including soldering etc as reqd. 3.8

Supply and fixing of decorative LED sentinel light (Mini SENTINEL -60W), WW SUSPMR

Supply and fixing of Single Arm Decorative Bracket H-1000mm, OH 750mm with flowerMR

Outdoor stand mounted Feeder Panel with 63A TP&N, MCB incomer, 63 amp TP contactor automatic switching of luminaires, Power tool control incomer outgoing terminal etc. as required (for high mast) (Basic Rate: 27,800.00+Over Head & [email protected]% = Rs. 31,956.00 )M-1546

Supply and installation of decorative Pole 4M, DIA 114-1000MM, DIA 76-2900MM with cast iron base. The pole is painted with polyurethane and its parts is painted in three layer coating in which first layer with each primer 2nd layer with epoxy primer and third final layer with PU paint and inbuild junction box to fix 32A connectorMR

Supplying and drawing following size of FR PVC insulated copper conductor 2x1.5 sqmm + 1x1.5sqmm cable in PVC conduit 1.7.1

Supply of XLPE insulated sheathed (heavy duty) armoured electric cables with Aluminium conductor for working voltage 1100 volts conforming to IS:7098 (part-1)/IS:1554; 2 core x16 sq mm (Basic Rate: Rs. 164.00 + Overhead & Profit @ 14.95% = Rs. 188.52)M-738

SITC of 8/9 Watt bollard light 9.8

Supply of XLPE insulated sheathed (heavy duty) armoured electric cables with Aluminium conductor for working voltage 1100 volts conforming to IS:7098 (part-1)/IS:1554; 2 core x10 sq mm (Basic Rate: Rs. 138.00 + Overhead & Profit @ 14.95% = Rs. 158.63)M-737

Supplying and drawing following size of FR PVC insulated copper conductor single core cable in existing surface/recessed steel/PVC conduit including dismantling as required 3x1.5 sqmm1.15.3

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required; 2 X 16 sq. mm (28mm)ED JSOR1473, 2806, 1006

Earthing with GI earth pipe 4.5 mtr long,40 mm dia including accessories and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal and salt as required. 3.2

S.I.T.C of Outdoor stand mounted feeder peeler with 63 amps TP&N,MCB incomer ,65 amps TP contractor automatic switch of luminaries, power tool control incomer outgoing terminal etc as required. (Basic Rate: Rs. 27800.00+ Overhead & Profit @ 14.95% = Rs. 31956.10)M-1546

Supply and Installation of 90W IP-66, RGBW LED Flood light Luminaries made of pressure die cast aluminium housing with powder coated, having protective toughened glass, with a system efficacy of >=120 lumens/watt, supply input voltage 120 - 270 V AC, leads to 24 V DC output voltage drives RGB LEDs with light angle 60°, surge protection 6KV and junction temperature < 70°C, CRI>70, P.F>0.9, suitable for RGB DMX 512 controller etc., complete with earth connection and not less than two years warranty.AP Elec 3.8.32 (a)

1m Double Arm suitable for 90mm top (Basic Rate Rs. 2490.00 + Overheads & Profit @ 14.95% = 2862.25)M757

Supply and Installation of 120W IP-66, RGBW LED Flood light Luminaries made of pressure die cast aluminium housing with powder coated, having protective toughened glass, with a system efficacy of >=120 lumens/watt, supply input voltage 120 - 270 V AC, leads to 24 V DC output voltage drives RGB LEDs with light angle 60°, surge protection 6KV and junction temperature < 70°C, CRI>70, P.F>0.9, suitable for RGB DMX 512 controller etc., complete with earth connection and not less than two years warranty.AP Elec 3.8.32 (b)

Supply and transportation of 36W RGB LED Linear Wall washer of Size 1000x38x58 mm with high power LEDs, made of pressure diecast aluminium housing with powder coated, supply input voltage 120 - 270 V AC, leads to 24 V DC output voltage drives, with beam angle of 15/25/45/ 60, P.F > 0.90, having system efficacy >=100 lumens/watt and junction temperature < 70°C, with ingress protection IP66, IK05, suitable for RGB DMX 512 controller etc., complete with earth connection and not less than two years warranty. AP Elec 3.8.33 (c)

Supply, transportation and installation of stand-alone USB -DMX controller to control a wide variety of different DMX systems from RGB/RGBW, including 1024 DMX channels, input power 5-5.5 V DC 0.6 A with programmability on PC, MAC, tablet, smart phone with micro SD card etc completeAP Elec 3.8.34

11/.433 KV DSS with 200 KVA Distribution TransformerJBVNL

Supply of XLPE insulated sheathed (heavy duty) armoured electric cables with Aluminium conductor for working voltage 1100 volts conforming to IS:7098 (part-1)/IS:1554; 2 core x16 sq mm (Basic Rate: Rs. 164.00 + Overhead & Profit @ 14.95% = Rs. 188.51)ED M-738

Supply of XLPE insulated sheathed (heavy duty) armoured electric cables with Aluminium conductor for working voltage 1100 volts conforming to IS:7098 (part-1)/IS:1554; 4 core x10 sq mm (Basic Rate: Rs. 189.00 + Overhead & Profit @ 14.95% = Rs. 217.25)ED M-739

Supply of XLPE insulated sheathed (heavy duty) armoured electric cables with Aluminium conductor for working voltage 1100 volts conforming to IS:7098 (part-1)/IS:1554; 4 core x16 sq mm (Basic Rate: Rs. 221.00 + Overhead & Profit @ 14.95% = Rs. 254.03)ED M-740

Supply of XLPE insulated sheathed (heavy duty) armoured electric cables with Aluminium conductor for working voltage 1100 volts conforming to IS:7098 (part-1)/IS:1554; 3.5 core x25 sq mm (Basic Rate: Rs. 280.00 + Overhead & Profit @ 14.95% = Rs. 321.86)ED M-726

Supply of XLPE insulated sheathed (heavy duty) armoured electric cables with Aluminium conductor for working voltage 1100 volts conforming to IS:7098 (part-1)/IS:1554; 3.5 core x35 sq mm (Basic Rate: Rs. 345.00 + Overhead & Profit @ 14.95% = Rs. 396.57)ED M-727

Supply of XLPE insulated sheathed (heavy duty) armoured electric cables with Aluminium conductor for working voltage 1100 volts conforming to IS:7098 (part-1)/IS:1554; 3.5 core x50 sq mm (Basic Rate: Rs. 452.00 + Overhead & Profit @ 14.95% = Rs. 519.57)ED M-328

Supply of XLPE insulated sheathed (heavy duty) armoured electric cables with Aluminium conductor for working voltage 1100 volts conforming to IS:7098 (part-1)/IS:1554; 3.5 core x185 sq mm (Basic Rate: Rs. 1398.00 + Overhead & Profit @ 14.95% = Rs.1607 )ED M-333

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade

as required; 3.5X 185 sq. mm (28mm)DSOR 9.1.27

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required; 3.5X 50 sq. mm (28mm)DSOR 9.1.22

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required; 3.5C X 35 sq. mm (28mm)DSOR 9.1.33

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required; 3.5C X 25 sq. mm (28mm)DSOR 9.1.33

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required; 4 X 16 sq. mm (28mm)DSOR 9.1.33

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required;4cX 10 sq. mm (28mm)DSOR 9.1.32

Supply of XLPE insulated sheathed (heavy duty) armoured electric cables with Aluminium conductor for working voltage 1100 volts conforming to IS:7098 (part-1)/IS:1554; 2 core x16 sq mm (Basic Rate: Rs. 164.00 + Overhead & Profit @ 14.95% = Rs. 188.52)M-738

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of size not exceeding 35 sq mm direct in ground including excavation and refilling the trench etc. as required including sand cushioning and protective covering 5.1

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of size above 35 sqmm and not exceeding 95 sq mm direct in ground including excavation and refilling the trench etc. as required including sand cushioning and protective covering 5.2

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of size above 95 sqmm and not exceeding 185 sq mm direct in ground including excavation and refilling the trench etc. as required including sand cushioning and protective covering 5.3

Laying of one number PVC ligulated end PVC sheathed/ XLPE power cable of l.l KV grade of size exceeding 35 sq mm but not exceeding 95 sq mm in ground including excavation and refilling the trench etc as rushed, but excluding sand cushioning 8nd protective covering5.18

Junction Box with 4 Pole Bus bar 100AMR

S/F 20 Amp SPN MCB industrial socket2.18

Supply of 400A, 415VAC FP auto transfer switch for instantaneous switching between sources as per IEC 60947-6-1, Closed transition, (bare unit- without enclosure) with voltage surge suppressor, communication interface etc., complete.AP 2.4.1

Supply Installation Testing and commissioning of free-standing floor mounted dust and vermin proof compartmentalized cubical outdoor panel made out of CRCA sheet, required hardware, cleaning with 7 tank process duly painted by two coats of zinc/red oxide primer followed by Powder coated / epoxy / PU painted with phosphitylation in grey or required shade after rinsing. The panel having PU/ Neoprene rubber gasket of not less than 3mm thickness, separate detachable, gland plate M.S. base channel, hinged door with locking arrangement for equipment/switchgear. The thickness of sheet shall not be less than 1.6mm The load bearing structure shall be of 2.0mm thick sheet supported by base M.S. channel if required. Main incomer 400 A TPN MCCB, DG incomer 400 A TPN MCCB, Changeover 400 A, 500A Aluminium busbar, Digital voltmeter meter with vss and digital ammeter meter with ASS, CT coil 150/5A, Outgoing feeder : 160 A 10 kA TPN-3 nos. 100 A 10 kA TPN-4 nos, 63A TPN MCCB-8 nos. 63A TPN MCB-8 nos, MCB 32 A DP MCB- 8 nos. internal wiring with suitable size of copper wire and cu lugs etc. as required MR

Wiring for light point /fan point/ exhaust fan point / call bell point with 1.5 sqmm FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit, with modular type switch, modular plat, suitable size G.I. box etc. as requiredJSR 1.3.3

Supply and fixing of 5/6 A one way Modular Type switch in existing boardJSR 1.24.1

Supply and fixing of 5/6 A 3Pin Modular socket in existing boardJSR 1.24.4

Supply and fixing of 15/16 A one way Modular Type switch in existing boardJSR 1.24.3

Supply and fixing of 15/16 A 3Pin Modular socket in existing boardJSR 1.24.5

S/F of Modular Type Fan Regulator JSR 1.25

S/F of 4/5 Module, Modular base & cover plateJSR 1.27.2

Supply and Fixing of 2pin 5 A ceiling RoseJSR 1.33

Supply and fixing of PVC /GI box of 4"x4"JSR 1.22.1

8 Way SPN , Double door MCB DB JSR 2.8.8

8 way (4 + 24), Double door, Horizontal6,peJSR 2.9.6

S/F 'C' Series , MCB 50/63 A TPNJSR 2.12.10

S/F 'C' Series , MCB 6/32 A DPJSR 2.12.5

S/F 'B' Series , MCB 32 A SPJSR 2.11.1

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of size above 35 sqmm and not exceeding 95 sq mm direct in ground including excavation and refilling the trench etc. as required including sand cushioning and protective covering 5.2

S/F 20 A SPN MCB industrial socket outletJSR-2.18

Installation , Testing & commissioning of fluorescent fitting direct on surfaceJSR 1.41

Wiring for ckt / submain wiring with earth wire (2x2.5sqmm + 1x2.5sqmm cu flexible cable)JSR 1.7.2

Power plug widng in PVC conduit (2 x 4 sq. nun) : Wiring for light/power plug with 2 x 4 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit, along with 1 No 4 sq.nrm FR PVC insulated copper conductor single core cable for loop earthing etc as required.JSR 1.5

1200mm (48") BLDC 5star rating 32W Ceiling Fan9.4.3

20 /22 W LED Tube light9.5.2

Supply and fixing of Batten holder1.34

9 / 10 Watt LED BulbM-855

12 " (230mm ) Exhaust fan M-775

ITC Exhaust fan up to 450mm sweep inexistent openingJSR 1.48

Earthing with GI earth pipe 4.5 mtr. Long 40mm dia including accessories and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal and salt as requiredJSR 3.2

Supply and laying of 6 SWG GI wire JSOR 3.8

Providing 12 mm thick cement plaster (1:6) -do- all complete as per building specification and direction of E/I.JH_BCD_2022_5.7.3

Providing 12 mm thick cement plaster (1:4) -do- all complete as per building specification and direction of E/I.JH_BCD_BCD_5.7.2

Providing 25mm thick water proof cement plaster -do-JH_BCD_2022_5.7.16

P/p G.I. lightning conductor finial :- Providing and fixing of lighting conductor finial , made of 25mm dia 300mm long , G.I. tube, having single prong at top, with 85mm dia 6mm thick G.I. base plate including holes etc. complete as required.JSOR 4.2

Pff G.I. lightning conductor tape in horizontal mn :- Providing and fixing G.I. tape 20mm x 3mm thick on parapet or surface of wall for lightning conductor complete as required.( for Horizontal run ).JSOR 4.7

Providing primer one coat of red lead paint of approved make over new steel surface -do- all complete as per building specification and direction of E/I.JH_BCD_2022_5.8.41

Providing two coat of synthetic enamel paint of approved shade and make over steel surface -do- all complete as per building specification and direction of E/I.JH_BCD_2022_5.8.45

PIF G.I. lightning conductor tape in vertical run :- Providing and fixing G.I. tape 20mm x 3rrm thick on parapet or surface of wall for lightning conductor complete as required.( for Vertical run )JSOR 4.8

Dismantling old plaster and pointing in cement or lime and raking out joints to 15mm. depth, watering and disposal of unserviceable materials with all leads all complete as per direction of Ell. 5.10.7

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete13.80 DSR

Providing two coats of plastic emulsion paint of approved shade and make over old surface -doJH_BCD_2022_5.8.20

Cement lead 3 km

Sand lead 35 km

(auto tip-up stadium chair with ppcp arms. hydergine material with blow moulding plastic chaired resistance, high strength with metal support, metal powder coating finish in side frame50/25mm, in Ms heavy 16 gauge.1- seat height to the floor 18 inch,2-back height to the floor 343-arms centre to centre 21 inch4-arms height to the floor 24 to 25 inch chair installed on 10 mm anchor fasner)MR

Extra for earth work in hard soil as per specification and direction of E/I (Vide classification of soil item_B)JH_BCD_2022 5.1.2

Earth Filling in foundation trenches and plinth in layers not exceeding 150mm thick well watered, rammed, fully compacted and fine dressed with earth obtained from excavation of foundation trenches within a lead of 50Mand lift of 1.5M all complete as per building specification and direction of E/I. (mode of measurement compacted volume)JH_BCD_2022_5.1.7

technical specification of fabric : -100% polyester 1100 dtexbase fabric yarn weave Panama weave (12*12)total weight/thickness 900 gsm/0.65mmwidth 300 cmsbreakingstrength (warp/weft) tear strength (warp/weft)adhesion 4000/4000 n/5cmflame retardancy 600/500 n m2/b1MR

Providing designation 75 B one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/l.JH_BCD_2022_5.6.3

providing & installation of zym equip mint commercialtreadmill,commercial cross trainer, spin bike, fly delt,cable crossover, fly delt,fly delt,leg extension/ curl dual, linear 45 degree leg press, flat bench chest press, incline chest press, Olympic decline bench, Olympic incline bench, flat bench,dumbellolympic plateMR

Providing designation 75 B brick work in C.M. (1:6) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/l.JH_BCD_2022_5.2.6

Providing and laying damp-proof course 50 mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5 mm nominal size).JH_BCD_2022 _ 5.3.5

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fi

tting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).DSR 10.28

Earthwork in excavation in foundation trenches in ordinary soil (vide classification of soil item-A) and disposal of excavated earth as obtained to a distance up to 50 M. including all lifts, levelling, ramming the foundation trenches, removing roots of trees, shrubs all complete as per approved design, building specification and direction of E/l.JH_BCD_2022_5.1.1

Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including' cost of all materials, labour, royalty and taxes all complete as per building specification and direction of E/l (Mode of measurement compacted volume).JH_BCD_2022_5.1.10

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering .all work up to plinth level:1:3:6 (1 Cement ;3 coarse sand (zone-III):6 grade stone aggregate 20 mm normal size)JH_BCD_2022_5.3.1

Providing designation 75 B brick work in C.M. (1:6) in superstructure with approved quality of clean coarse sand of F.M. 2 to2.5 including providing 10 mm thick mortar joints cost of screening materials , scaffolding , raking out joints to 15mm depth curing, taxes and royalty all complete as per building specification and direction of E/l.JH_BCD_2022_5.2.14

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering,shuttering ,finishing and reinforcement- all work up to plinth level,1:1.5:3(1 cement : 2 coarse sand : 4 graded stone aggregate 20mm normal size).JH_BCD_2022_5.3.9.1

Reinforced cement concrete work min wall (any thickness), including attached pilasters,buttresses,plint and string courses,fillets,column,pillars,piers,abutments,posts and struts etc. above plant level up to floor five level, excluding cost of centring, shuttering ,finishing and reinforcement: 1:1.5:3( 1 cement : 1.5 coarse sand (zone-III) :3 grade stone aggregate 20 mm normal size).JH_BCD_2022_5.3.10

Reinforced cement concrete work min wall (any thickness), including attached pilasters,buttresses,plint and string courses,fillets,column,pillars,piers,abutments,posts and struts etc. above plant level up to floor five level, excluding cost of centring, shuttering ,finishing and reinforcement: 1:1.5:3( 1 cement : 1.5 coarse sand (zone-III) :3 grade stone aggregate 20 mm normal size).JH_BCD_2022_5.3.10

Reinforced cement concrete work min wall (any thickness), including attached pilasters,buttresses,plint and string courses,fillets,column,pillars,piers,abutments,posts and struts etc. above plant level up to floor five level, excluding cost of centring, shuttering ,finishing and reinforcement: 1:1.5:3( 1 cement : 1.5 coarse sand (zone-III) :3 grade stone aggregate 20 mm normal size).JH_BCD_2022_5.3.10

Reinforced cement concrete work in beam, suspended floors, roofs having slope up to150 landings,balconies,shelves, chajjas,lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floors five level, excluding the coast of centering,shuttering,finishing and reinforcement ,with 1:1.5:3(1 cement :1.5 coarse sand (zone III) :3 graded stone aggregate 20 mm normal size).JH_BCD_2022_5.3.11

Reinforced cement concrete work in arches,archribs, domes , vaults,shells,folded plate and roofs having slope more than 150 up to floor five level, excluding the cost of centring, shuttering, finishing and reinforcement, with 1:1.5:3(1 cement : 1.5 coarse sand (zone-III):3 graded stone aggregate 20mm normal size).JH_BCD_2022_5.3.13

Cantering and shuttering including strutting, propping etc. And removal of form for. 5.3.17.1

Cantering and shuttering including strutting, propping etc. And removal of form for. 5.3.17.6

Cantering and shuttering including strutting, propping etc. And removal of form for. 5.3.17.5

Cantering and shuttering including strutting, propping etc. And removal of form for. 5.3.17.9

Cantering and shuttering including strutting, propping etc. And removal of form for. 5.3.17.4

providing and fixing at or near ground level precast cement concrete in kerbs, edgings etc. asper approved pattern and setting in position with cement mortar 1:3 (1 cement :3 cores sand),including the cost of requirement centering,suttering complete.1:11/2 :3 (1 cement :11/2 coarse sand (zone-III):3 grade stone aggregate 20mm nominal size).JH_BCD_2022_5.3.4

Providing TMT reinforcement of following Dia rods as per approved design and drawing including carriage of M.S. rods of (Straight or in coils) to work site, cutting, bending and binding with annealed wire with cost of wire removal of rust placing the rods in position all complete as per building specification and direction of E/I.JH_BCD_ 5.5.5(A)_2022

Providing and fixing factory made P.V.C. door frame of size 50x47mm with a wall thickness of 5mm, made out of extruded 5mm rigid PVC foam sheet mitred at corners and joined with 2 Nos. of 150mm long brackets of 15x15mm M.S. square tube, the vertical door profiles to be reinforced with 19x19mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100mm size complete as per manufacturers specification and direction of Engineer-in-Charge. DSR_2023_ 9.119/212

Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19mm x 19mm for styles and 15x15mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture . M.S. frame covered with 5mm thick heat moulded PVC 'C' channel of size 30mm thickness, 70mm width out of which 50mm shall be flat and 20mm shall be tapered in 45degree angle on both side forming styles; and 5mm thick, 95mm wide PVC sheet out of which 75mm shall be flat and 20mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115mm wide PVC sheet out of which 75mm shall be flat and 20mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10mm (5mm x 2 ) thick, 20mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail. panelling of 5mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7mm (5mm+2mm) thick x 15mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5mm thick PVC strip of 20mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge. Manufacturer’s specification & drawing. (ii)30 mm thick pre laminated PVC door shutters.DSR _2023_ 9.120.2/163

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conf

Providing 12mm cement plaster (1:3) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.JH_BCD_2022_5.7.1

Providing 6mm thick cement plaster (1:4) in ceiling with clean coarse sand of F.M. 1.5 -do-JH_BCD_2022_5.7.6

Providing 25mm thick water proof cement plaster -do-JH_BCD_2022_5.7.16

orming to IS : 733 and IS: 1285 fixing with dash fasteners of required Dia and size, including necessary filling up the gaps at junctions i.e. at top, bottom and sides with required DPDM rubber/neoprene gasket etc., aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/panelling C.P. brass/stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge (Glazing, panelling and dash fasteners to be paid for separately) Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron)DSR _2023_ 21.1/200

Providing two coats of plastic emulsion paint of approved shade and make over a coat of cement primer over new surface including preparing plastered surface by rubbing smooth with pumice stone or fine sand paper, applying putty wherever required, scaffolding washing of floor and taxes all complete as per building specification and direction of E/l.JH_BCD_2022 5.8.21

Providing two coats of plastic emulsion paint of approved shade and make over a coat of cement primer over new surface including preparing plastered surface by rubbing smooth with pumice stone or fine sand paper, applying putty wherever required, scaffolding washing of floor and taxes all complete as per building specification and direction of E/l.JH_BCD_2022 5.8.21

Providing two coats of synthetic enamel paint of approved shade and make over steel surface -do-JH_BCD_2022_5.8.45

Wiring of Light & Fan Point including 1.5 sqmm Cu , PVC insulated copper conductor with modular type switch, modular plat, suitable size GI box etc. as requiredJH_SOR_2022_ 1.1

Supply and fixing of 15/16 A one way modular switch in existing boardJH_SOR_2022_ 1.23.3

Supply and fixing of 15/16 A 6 Pin socket in existing boardJH _SOR_2022_ 1.23.5

Power Plug wiring in PVC conduit 2x 4 sqmm FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit along with 1 Nos. 4sqmm FR insulated copper conductor single core cable for loop earthing as requiredJH_SOR_ 1.5

Supply and fixing of 5/6 A one way modular switch in existing boardJH_SOR_2022_ 1.24.1

Supply and fixing of 5/6 A 3Pin socket in existing boardJSOR 1.24.3

S/F Modular boxes, base & cover plate size 1 or 2 ModuleJSOR 1.27.1

Providing and fixing glazing in aluminium door, windows, ventilators, shutters and partitions etc, with EPDM rubber/neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge (cost of aluminium snap beading shall be paid in basic item) With float glass panes of 5 mm thickness DSR_2023_ 21.3/201

Supplying, fitting and fixing M.S. grill made of 20x6mm M.S. flat as per approved design and drawing, properly fabricated with joints continuous fillet welded and finished smooth , carriage of grill to work site, hoisting as per building specification and direction of E/l. (where materials is not supplied by the depth.)JH_BCD_2023_5.5.30

Providing and laying Double charge vitrified floor Lites in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622 / ISO 13006 of approved make, In all colours and shades, laid on 20mm thick cement mortar 1 :4 (1 cement: 4 coarse sand). Jointing with grey cement slurry@ 3.3 kg/ sqm Including grouting the Joints with white cement and matching c l events etc., complete. Size of Tile 600x600 mm.JH_BCD_2023_5.6.28

Providing and fixing 18 mm thick gang saw cut ,mirror polished - -do- all complete as per building specification and direction of E/I. Granite stone slab colour black ,cherry / Ruby red (MAIN ENTRANCE GATE)DSR_2023_8.2

Providing and laying 25mm thick white Makrana marble stone slab flooring of approved quality over 19mm thick lime mortar (1:1:1) (lime putty:" Surkhi : Coarse sand) laid and joined with white cement slurry including rubbing and polishing to granolithic finish with approved quality of carborundum stone including cost of curing, taxes and royalty all complete as per building specification and direction of E/I. (ii)300X600JH_BCD_2022_5.6.21_(ii)

Providing and laying water proofing treatment in sunken portion ofWCs, bathroom etc., by applying cement slurry mixed with waterproofing cement compound consisting of applying :(a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.DSR_2023_ 22.5

S/F Modular boxes, base & cover plate size 8/9 ModuleJSOR 1.27.4

Supply and Fixing of 2pin 5 A ceiling RoseJH_SOR_2022_ 1.33

Supply and fixing of Batten holder/angle holder including connection etc as requiredJH_SOR_2022_ 1.34

Supply and fixing of 4 Way Double door three pole and neutral MCB DB, 240 volts, on surfaces / recess. (63 amp)JH_SOR_2022_ 2.14.1

Supply and fixing following rating double pole .240 volts,isolator in the existing MCB db. complete with connection ,testing and commissioning etc as required JH_SOR_2022_ 2.8.4

Supplying and laying 6 SWG GI wire at 0.5 m below ground level for conductor earth electrode, including soldering etc. as requiredJH_SOR_2022_3.8

20/22 W LED Tube lightJH_SOR_2022_9.5.2

Supply of 1200 mm Ceiling FanJH_SOR_2022_ 9.4.1

P/F male ended 15 mm dia brass bib cock of app. Quality ( wt. not less than 350 gms) - do - all complete as per specification and direction of E/l. JH_DWSD_2022_ 3.1.5.1

Supply and fixing of 63 A TPN MCBJSOR 2.17.3

Supply and fixing of 6A/32 A SP MCBJSOR 2.11.1

Making holes in wall for laying GI pipe and restoring the same after pipe - do - all complete as per specification and direction of E/l.JH_DWSD_2022_ 3.1.18

Wiring for cut / submain wiring along with earth wire (2x2.5sqmm + 1x2.5sqmm cu flexible cable) singe core cable in surface / recessed PVC conduit as requiredJH_SOR_2022_ 1.7.2

(b) Glass shelf with C.P brass rail (450 mm x 125 mm)

(c) C.P brass soap dish container medium quality

Supply and drawing of 2 x 1.5 sqmm size of FR PVC insulated copper conductor, single core cable in the existing surface / recessed steel / PVC conduit as requiredJH_SOR_2022_1.7.1

Supply and drawing of 4 x 6 sqmm size of FR PVC insulated copper conductor, single core cable in the existing surface / recessed steel / PVC conduit as requiredJH_SOR_2022_1.7.4

Earthing with GI earth pipe 4.5 mtr. Long, 40mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal and salt as required (63 amps )JSOR3.3

P/F G.M non return valve horizontal / vertical - do - all complete as per specification and direction of E/l. (15 mm dia)JH_DWSD_2022 3.1.7

Labour for laying , fitting and fixing NP2 R.C.C spun pipe - do - all complete as per specification and direction of E/l. JH_DWSD_2022_ 3.3.6.2

Supplying materials and labours for constructing inspection chamber of des. 75 B brick internal size (600 mm x450 mm x 750 mm) - do - all complete as per specification and direction of E/l. JH_DWSD_ 3.3.8

Cutting chajja or cornice for laying G.I pipe and restoring the same with RCC (1:2:4) - do - all complete as per specification and direction of E/l.JH_DWSD_2022_3.1.17

Supplying and fixing NP2 hume pipe etc. (150 mm ) - do - all complete as per specification and direction of E/l. DSR_2023_19.6.2

S/F/F the following item - do - all complete as per specification and direction of E/l. (a) Mirrors of 6 mm thick plate glass bevelled edge mirror JH_DWSD_2022_ 3.1.21

Providing and fixing white vitreous China pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous China flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :JH_DWSD_2022_ 3.2.2 (i)-a ©

P/F CPVC pipes having thermal stability for hot and cold water supply - do - all complete as per specification and direction of E/l. DSR _2023_18.7.3

S/F/F flat back or angular lipped front vitreous white glazed earthen wave urinal of Hindustan 'parry' - do - all complete as per specification and direction of E/l. Flat back or standing corner (600 mm x 350 mm)JH_DWSD_2022 3.2.3 (a)

S/F/F vitreous white glazed earthen wave wash hand basin of parry Hindustan - do - all complete as per specification and direction of E/l. JH_DWSD_2022_ 3.2.5

E/W in excavation for laying of diff. types and sizes of R.C.C spun pipe - do - all complete as per specification and direction of E/l. JH_DWSD_2022_ 3.3.1 (I)

P/V and placing on terrace polyethene water storage tank - do - all complete as per specification and direction of E/l. M-079

Supplying the following bathroom fittings - do - all complete as per specification and direction of E/l. bib cock18.49.1

Paper holder V.I.P17.34.1

P/F CPVC pipes having thermal stability for hot and cold water supply - do - all complete as per specification and direction of E/l. 15 mm dia. DSR _2023_18.8.

20 mm dia.18.8.2

40 mm dia18.7.5

P/F PTMT grating of appv. Quality and colour - do - all complete as per specification and direction of E/l. C.P gratings circular type 100 mm dia DSR_2023_18.58

Cement lead 3 km

Sand lead 35 km

Stone chips lead 17 km

Providing TMT steel reinforcement - do - all complete as per building specification and direction of E/I.5.5.5(a)

Centring and shuttering including strutting , propping etc. and removal of form for foundation , footing , bases of columns, etc for mass concrete.JH_BCD_2022_5.3.17.1

Bricks lead 8 km

Earth work in excavation in foundation trenches - do - all complete as per building specification and direction of E/I.JH _BCD_2022_5.1.1

P/V and laying of 110 mm dia PVC pipe for outlet of water to incl. all accessories - do - all complete as per specification and direction of E/l. 75 mm PVC PIPE12.41.2

Providing 1.5 mm cement punning including screening curing with all leads and lifts of water ,scaffolding taxes and royalty all complete as per building specification and direction of E/I.JH_BCD_2022_5.7.11

110 mm Pve PIPE12.41.2

P/F PVC pipe fitting with all accessories - do - all complete as per specification and direction of E/l. 110 mm plain tee (supreme) PVC12.4.2

Cement lead 3 km

Sand lead 35 km

Stone chips lead 17 km

110 mm plain band12.42.5

110 mm coil (supreme)12.42.1

110 mm plain floor traq12.42.6

Providing P.C.C (1:2:4) in foundation -do - all complete as per building specification and direction of E/I (for locking)JH_BCD_2022_5.3.1.2

16.91.1 Providing and laying factory made coloured chamfered edge cement concrete paver block of required strength , thickness and size/shape, made by vibratory method using PU mould laid in required colour & pattern over 50mm thick compacted bed of fine sand ,compacting and proper embedding /laying of inter locking paver blocks in to the sand bedding layer through vibratory compaction by using plate vibrator , filling the joints with sand and cutting the paver blocks as per required size and pattern ,finishing and sweeping extra sand in footpath parks, lawns, drive ways or light traffic parking etc. complete as per manufacturer's specifications and direction of E/I. 60mm thick C.C. paver block of M-35 grade with approved colour, design and pattern. 4.23 A

Construction of granular sub-base

by providing closegradedMaterial,mixinginamechanicalmixplantatOMC,carriageofmixedMaterialtoworksite,spreadinginuniform layers with motor grader on prepared surface and compacting with vibratory power roller(baby / tendon) to achieve the desired density, complete as per clause 401.SOR-4.01(A)

Paver lead 11 km

Trenching in ordinary soil up to depth of 60 cm and removal and stacking - do - all complete as per specification and direction of E/l.2.1 D.S.R 2023

Providing 75 B brick work in CM (1:6) in foundation - do - all complete as per specification and direction of E/l.5.2.6 BCD

Providing CP (1:4) - do - all complete as per specification and direction of E/l.5.7.2 BCD

Providing and fixing 18 mm thick gang sawcut ,mirror polished - -do- all complete as per building specification and direction of E/I.Granite stone slab colour black ,cherry / Ruby red8.2 DSR

Filling in foundation trenches and plinth in layers not exceeding 150mm ,thick well watered rammed fully compacted and fine dressed with earth obtened from excavation of foundation trenches within a lead of 50 m and lift of 1.5 m all complete as per building specification and direction of E/l (mode of measurement compacted volume).JH_BCD_2025_ 5.1.7

Trenching in ordinary soil up to a depth of 60 cm including removal and stacking of serviceable materials and then disposing of surplus soil, by spreading and neatly levelling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or / and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure).H&L_DSR_2025_ 2.1/pg_95

Supplying and stacking of good earth at site including royalty and carriage up to 5 km complete (earth measured in stacks will be reduced by 20% for payment).H&L_DSR_2025_ 2.2/pg_95

Supplying and stacking sludge at site including royalty and carriage up to 5 km complete (sludge measured in stacks will be reduced by 8% for payment).H&L_DSR_2025_ 2.3/pg_95

Supplying and stacking at site dump manure from approved source, including carriage up to 5 km complete (manure measured in stacks will be reduced by 8% for payment) : 2.4.3 Screened through sieve of I.S. designation 4.75 mmH&L_DSR_2025_2.4_ 2.4.3/pg_95

Uprooting weeds from the trenched area after 10 to 15 days of its flooding with water including disposal of uprooted vegetation.H&L_DSR_2025_ 2.6/pg_95

Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately).H&L_DSR_2025_ 2.8/pg-95

Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in-chargeH&L_DSR_2025_ 2.9/95

Preparation of beds for hedging and shrubbery by excavating 60 cm depend trenching the excavated base to a further depth of 30 cm, refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8:1 (8 parts of stacked volume of earth after reduction by 20% : one part of stacked volume of sludge or manure after reduction by 8%),flooding with water, filling with earth if necessary, watering and finally fine dressing, levelling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and levelling as directed, within a lead of 50 m, lift up to 1.5 m complete (cost of sludge, manure or extra earth to be paid for separately)H&L_DSR_2025_ 2.13/97

Supply and stacking of Delo nix regia (Gulmohar) plant of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-chargeH&L_DSR_2025_ 7.24/180

Providing, stacking and Displaying Seaforthia Palm having ht. 1.50 m to 1.80 m with 12-15 suckers, well developed, fresh and healthy lush green leaves from bottom to top in 30 cm size of Earthen pot / Plastic pot and as per direction of the officer-in-charge.H&L_DSR_2025_ 3.74/132

Supply and stacking of Nauclea cadamba (Kadam) plant of height 150-165cm. in big poly bag of size 25 cm as per direction of the officer-in-charge'sH&L_DSR_2025_ 7.60/184

Providing and stacking of Polyalthia longifolia (Ashok) of height 180-195 cm. in gunny bag of size 30 cm as per direction of the officer-in-charge.H&L_DSR_2025_ 7.75/188

Providing and stacking of Azadirachta indica ( Neem ) of height 120-130cm in big polybag of size 25 cm as per direction of the officer-in-charge.H&L_DSR_2025_ 7.5

Providing and stacking of Bassia latifolia (Mahua) of height 90-105 cm. in big polybag of size 25 cm as per direction of the officer-in-charge.H&L_DSR_2025_ 7.6

Providing and stacking of Bottle palm of ht. 270-300 cm bottom girth 40-50 cm well developed in big HDPE bags as per direction of the officer-in-charge.H&L_DSR_2025_ 7.12

Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserviceable material’s as per direction of officer in charge (excluding cast of plant & water) 2.57.1 Trees PlantH&L_DSR_2025_ 2.57.1

Complete maintenance of the entire garden features having as per yard stick in the garden area i.e. lawn trees, shrubs, hedge, flower beds, foliage's, creepers etc. including hoeing, weeding pruning replacement of plants, gap filling, watering, mowing of lawn, grass cutting by lawn mover and brush cutter , removal of garden waste, applying insecticide, pesticide & fertilizers(whenever required) top dressing of lawn with good earth and manure and maintenance of other garden related works as directed by office-in-charge (Cost of Good Earth, Manure, Fertilizer, Insecticide , Pesticide will be provided by the Department & lawn mover and brush cutter with fuel , other T & P material/articles shall be provided by the contractor.) Open spaces(as per yard stick 1Mali =3.00Acre).H&L_DSR_2025_ 2.40.6/107

P/F of G.I pipes complete with G.I fittings incl.-do- all complete as per specification and direction of E/I.25 mm dia.DSR-18-12

50 mm dia.18.12.6

Painting G.I pipes and fitting with two coat ofanti corrosive bitumastic paint - do- all complete as per specification and direction of 25 mm dia.DSR-18.40

50 mm dia.18.40.5

P/F of gun metal gate valve with CI wheels -do- all complete as per specification and direction of E/I.25 mm dia.18.17.

50 mm dia.18.17.4

Sand lead 35 km

Centring and shuttering including strutting , propping etc. and removal of form for foundation , footing , bases of columns, etc for mass concrete.JH_BCD_2022_5.3.17.1

P/v and filling sand of grading zone V orcoarse grade -do- all complete as per specification and direction of E/I.25 mm dia.18.41

Add 18 % GST ( In Basic Rate must fill 18)

Add 1 % Labour cess ( In Basic Rate must fill 1)