CERTAIN REPAIRS TO WATER PROOFING TREATMENT TO ROOF PLASTERING GLAZING AND OTHER MISC WORKS UNDER AGE BR 1 GE AF NO 2 JODHPUR AT AF STN JODHPUR AND AFS MANDORE

Amount

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for (roof padding, flooring above ground floors) including roof treatment and removing from site all as specified and directed.

Taking down cement plaster, any description on brick, concrete or stone walls or ceiling including racking out joints, hacking for key, scrubbing down with water etc and removal of rubbish off all as specified and directed.

M&L for rendering 20 mm thick in CM 1:4 with using integral water proofing compound on stone masonry surfaces finished even and smooth (without using extra cement). Note: Integral water proofing compound shall be measured and paid for separately as “Supply only”.

M&L for 50 mm thick (average) cement concrete 1:3:6 type C-0 mix (12.5 mm graded stone aggregate) in padding over roof.

M&L for 10 mm thick rendering in CM 1:3 over concrete surfaces (Roof) mixed with water proofing compound @ 3% by weight of cement complete all as specified. NOTE : Water proofing compound shall be measured and paid for separately as “Supply only”

Supply only integral water proofing compound ISI marked.

M&L for applying roof treatment on top of roof with APP modified membrane (minimum 3 mm thick) with non-woven polyster reinforcement/mat (centre core) with thermal insulation with white mineral gravel finish on upper side of membrane laid by torch application method with overlaps 100mm on length side and 100 mm on the width side as per manufacturer’s instructions over and including a coat of approved cold applied bituminous oil based primer (IS- 3384) @ 250 gm/sqm over cleaned roof surface complete all as specified and as directed by Engineer-in-Charge.

Dismantling existing tanks, any capacity, setting aside (or lowering if required) for repairs of roofs and hoisting if required, reconnecting and refixing in position (Repairs to roofs measured separately).

Disconnecting existing tanks of any description exc. 250 ltrs and n.exc. 500 ltrs capacity and removing from site.

Disconnecting existing tanks of any description exc. 500 ltrs and n.exc. 1000 ltrs capacity and removing from site.

S&F 500 litres capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top thread type cover), hoisted and fixed in position all as specified in SSR Part-I, connecting up pipes including 20 mm bore ball brass valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic plastic ball screwed for iron pipe and fixed. (Minimum weight of ball valve - 210 gms)

S&F 1000 litres capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top thread type cover), hoisted and fixed in position all as specified in SSR Part-I, connecting up pipes including 20 mm bore ball brass valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic plastic ball screwed for iron pipe and fixed. (Minimum weight of ball valve - 210 gms)

Taking up or down steel tubing 15mm bore and connections including cleaning for refixing or removing from site.

Taking up or down steel tubing 20mm bore and connections including cleaning for refixing or removing from site.

Refixing old steel tubing, 15mm bore, and connections with new or old position (Walls, ceiling, floors, etc.) Note :- Steel tubes obtained from item No. 13 above shall be used under this item.

Refixing old steel tubing, 20mm bore, and connections with new or old position (Walls, ceiling, floors, etc.) Note :- Steel tubes obtained from item No. 14 above shall be used under this item.

Supply and laying 15mm bore tubes, galvainzed steel, medium grade, with all fittings and fixed complete to walls and ceilings or laid in floors all as specified and directed.

Supply and laying 20mm bore tubes, galvainzed steel, medium grade, with all fittings and fixed complete to walls and ceilings or laid in floors all as specified and directed.

S&F in repair for 110 mm PVC(SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors,walls height upto 12.0 m with required number of PVC clamps incl fixing make: Prince or supreme or eqvilant complete all as specified and directed.

S&F in repair for 110 mm bore PVC (SWR) bend, suitable for type ‘A’ pipes, any radius.

Taking down Shutters of any description exc 1 sqm and n exc 2 sqm each

Taking down Shutters of any description exc 2 sqm each

Taking down chowkats or frames exe 1.5 Sqm but n.exc 4 sqm each with shutter (without taking off shutters from the frame) and removing from site complete all as directed.

Taking down chowkhat or frame n exc 1.50 sqm each (with out taking of shutters from the frame) and removing from site complete all as directed.

S&F for second class hard wood plain, solid, straight, chowkats and frame wrought framed, put together, with glue, pinned at joints, all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provide for shutters, doors, gates etc

Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doo0rs etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive or steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing of Fe-290(Gde E-165) complete

S & F Plain framed, panelled shutter of 2nd class hard wood (two panel) of 35mm thick factory made shutter with lock rail and panel of 9 mm B.W.P commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS: 1003 (Part I), kiln seasoned and chemically pressure treated

S&F Flush shutters,40 mm thick with block board core and plywood face panels, commercial type on both sides

M/L for Glazed and skeleton shutters of thickness 35mm of IInd class hard wood , open rebated and prepared to receive glass, gauze, etc. (without sash bars), edge of framing plain, chamfered or rounded, fitted with cut and mitred beds for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.20 (a); supplied and fitted to chowkats Note: Glazed or cloth etc in panelsor sash square shall be measured seperately

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples.

Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, supplying & fixing in opening as per specification & drawing

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel heaving a PVC sheet strip of 20mm width suck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing.

S&F Butt hinges,extruted aluminium alloy with galvanised mild steel type C21of size 100 mm.

S/F floor door stoppers of alluminiun alloy body and toung , anodised with harddrawn steel spring with overall length of cover plate is 140 mm

S&F Aluminium anodised barrel tower bolt of extruded section 150mm size

S&F Aluminium anodised barrel tower bolt of extruded section 200 mm size

S&F Aluminium alloy anodised sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed size 300mm long.

S&F extructed aluminium alloy handles, fabricated type,anodised of size 150mm.

M&L for preparation of new wooden surface of any description over 10cm width or girth and applying two coats of synthetic enamel paint (1stquality) over one coat of pink primer complete all as specified and directed.

Resecuring or easing and adjusting without taking down shutters of any description n exe 1 sq.m each

Resecuring or easing and adjusting without taking down shutters of any description exe 1 sq.m but n exe 2.0 sqm each

Resecuring or easing and adjusting without taking down shutters of any description exe 2.0 sqm each

Welding in repairs exc 2.5 cm & n exc 5 cm in length & thickness of metal n.exc 6 mm

S&F 3mm thick sheet glass, ordinary quality and glazing with oil putty in square n.exc 0.5 sqm in each pane incl glazing clips after hacking out old broken glassfrom metal frame incl punching or drilling old glzing pins.

S&F 3mm thick figured glass, pin headed type and glazing with oil putty in square n.exc 0.5 sqm in each pane incl glazing clips after hacking out old broken glassfrom metal frame incl punching or drilling old glzing pins.

S&F in repairs Galvanised MS wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or galvanised wire staples.

S/F in repair door closer hydraulically regulated,aluminium extruded section body designation No. 2 universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg and fixed

S&F in repairs 300 mm, mild steel, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

S/F in repair floor door stoppers of alluminiun alloy body and toung , anodised with harddrawn steel spring with overall length of cover plate is 140 mm

S/F in repair wooden cleat door stoppers size of 100x40x40mm fixed with 50mm mild steel hinges in doors complete all as specified and directed.

S&F in repairs Aluminium anodised barrel tower bolt of extruded section 150mm size

S&F in repairs Aluminium anodised barrel tower bolt of extruded section 200 mm size

S&F in repairs Butt hinges,extruted aluminium alloy with galvanised mild steel type C21of size 100 mm.

S&F in repairs Aluminium alloy anodised sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed size 300mm long.

S&F in repairs extructed aluminium alloy handles, fabricated type,anodised of size 150mm.

S&F in repairs extructed aluminium alloy handles, fabricated type,anodised of size 100mm.

S& F in repairs Prelaminatd particle board, interior grade 18/19 mm thick , prelaminated both side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber work or other place as builtup furniture as specified and as directed,

S & F Plain fillets 2nd class hard wood of sectional area not exe 3 sq cm , square, rectangular or triangular in section, clean sawn, secured with mills or brads.

S& F butt hinges ,75 mm of size cast brass with mild steel hinge pin, bright polished type B-11

S& F 75 mm size brass handles, cst type, polished bright finished.

S&F in repair magnetic catch ball with 8mm dia steel ball and brass body and striking plate including letting in and fixed

S&F 6 mm thick plywood in repaire, grade BWP, type BB, fixed with screws to timber frame work complete all as specified and directed.

S&F in repairs projecting type hinges of steel window/ventilator, 75 mm long including necessary fixing & welding work etc complete all as specified and directed.

S&F in repairs peg stay 250 mm/300 mm long stopping of steel window/ventilators including welding(if required) & fixing complete all as specified and directed.

S&F in repairs left/right MS handle of steel windows including welding(if required) & fixing complete all as specified and directed.

S&F in repairs 100mm ms tower bolt of steel windows including welding(if required) & fixing complete all as specified and directed.

Repair to steel windows n.exc 1.00 sqm including welding, easing, re-alignment of shutters by taking down & refixing (if reqd) etc complete all as specified and directed

Repair to steel windows exc 1.00 but n. exc 2.00 sqm including welding, easing, re-alignment of shutters, by taking down & refixing (if reqd) etc complete all as specified and directed

Repair to steel ventilators including welding, easing, re-alignment of shutters, by taking down & refixing (if reqd) etc complete all as specified and directed

S&F in repair drapery rod in any length, high strengh MS pipe with corrugated PVC extrusion having outer dia 28 mm with plastic ring of ABS plastic of dia 56 to 58 mm all as directed by Engineer-in-charge

S&F in repair decorative finals ABS plastic fancy type bracket, fancy type hook in matching colour of steel powder quoted paint of same colour of rod incl all as directed Engineer-in-charge.

S&F in repairs solid rubber beading of 30 to 50 mm wide and 3 to 5 mm thick fixing at bottom to existing doors complete all as specified and directed.

M&L for preparation of new plastered or unplastered surfaces of walls and applying two coats of cement base paint, white or tinted, all as directed.

M/s. Dhananjay Construction

DEV INDUSTRIES

Siddharth Constructions

BAGHELA CONSTRUCTION

Bansal Enterprises