Providing, installation, testing and commissioning of Pumping Machinery along with allied electro-mechanical equipments at WSS Shahzadpur (NABARD)

Amount

Providing, Installation, testing and commissioning of Submersible Pump Set 5000 GPH X 100 MH-02No(01installed and 01No standby) at tube well, along with allied works by way of fabrication of 80mm dia GI column pipes 10 feet long welded with MS flanges-80mm dia at both ends-20nos for making delivery of the pump. Fabrication of GI pipe nipple with threads at one end & MS flange at other end & fastening the threaded end of nipple with the delivery of pump. Fabrication of gantry by way of making of base frame of MS channel and plates of required size. Grouting the base frame at bore well site, fab/erection of G.I. pipe nipples at both ends of the base frame, welding of pipe nipple of required size at top. Fabrication of MS clamps 80mm dia. - 02 sets for holding submersible pump & nipples. Providing of chain pulley block heavy duty of capacity 02 ton -01 no. Providing /Fitting of 6 mm square three core sub cable for making of electrical connection from motor to control panel with proper thimbling & insulation. Coupling of pump motor with the help of coupling pulley. Lowering of pump motor set along with GI pipe nipples and submersible cable into the Bore well with the help of chain pulley block, ropes & skilled/unskilled labours. Providing/Fitting of MS bends 80mm dia. with MS flanges. Providing/Fitting of 80mm dia sluice valve & check valve 80mm dia-01no each with MS flanges, nut/bolts & washers, and interconnecting with the raising main with all allied welding work.Complete job includes cost of material, labour charges & carriage charge.

Fabrication and fitting /grouting of angle iron panel board fitted with 12mm thick water proof ply with good quality mica. Providing/fitting of 200Amp 415V HRC type main switch (H/DUTY) -01 no, Providing/fitting of 135mm square aluminium cable -20 mtr-3.5 core for making of connection from LT fuse system to main switch with proper thimbling and insulation. Providing /fitting of 100amp busbar on the panel board. Checking continuity of whole electric circuit. Testing and commissioning of electro mechanical works by checking of all electrical connections, tapping and tightening all other connections. Testing the machinery on full load. Complete job

Fabrication/ Manufacturing of 100KVA Voltage Stabilizer at Oil cooled unbalance Type 415Volt at pumping station Seri Sayal stage ist, Complete with Transformer Oil in Copper windings capable of operating on unbalanced Voltage. Installation, testing & commissioning of 100KVA voltage stabilizers by way of carriage/ shifting of stabilizer to site of work on MT and HL. P/F of Aluminium cable 185mm sq unarmoured-20mtr appox of standard ISI make(as per site condition) for making connections from main switch to Voltage stabilizer for all the three phases in three leads with neutral & then from stabilizer to buss bar fuse system with proper thimbling duly crimpled by using crimpling tool & proper insulation. Filling of transformer oil up to required level after heat treatment/dehydration to make it moisture free. Job includes cost of material and Fitting charges. specification as below Capacity : 100KVA Phase : 03 Make Confirming to relevant ISO With all latest amendments Input voltage : (160-380 ) volt Output voltage : 415 volts +/- 1% Type : Manually operated Correction Rate : 12 to 35 V/sec Regulation : +/- 1% Frequency : 48 to 52 Hz Cooling Method : Oil Cooled Efficiency : 95% High & Low cut off : Installed with standard Capacity By pass change over Switch : Yes MCCB : Heavy Duty Single phase preventer : Yes Material of Construction : The Core should be first quality (CRGO) Silico Steel core, Conducting conductor should be off 99.95% of Electrolytic Copper MS Steel thickness of container 14/16 SWG. Transformer Oil to be used shall be of best quality Conforming of IS 335 with latest amendments. Voltage stabilizer shall be mounted on 02 pairs of H/D MS wheels for making shifting/ fixing easy. Voltmeter/Ampere meter Good quality ISI make of Required Specification, Toggle Switch 03 No for input/output reading of each face Rotary Switches Of suitable Amp range each of 08steps. Painting shall be enameled steel grey / Green Colour.

Testing and commissioning of pump motor set with all other allied electro mechanical works. Checking of all electrical connections, tapping and tightening all other connections. Plugging of leaking joints if any by way of welding, replacement of gaskets and tightening of nuts and bolts. Checking the alignment of pump and motor sets and testing the machinery on full load. Complete job

INTERNATIONAL ELECTRICAL AND ENGINEARING

SMART TECH AND CO

NATIONAL ELECTRO-MECH COMPANY

PERFECT ELECTRICAL WORKS

M/S FASTTRACK ENGINEERS

SUNIL KUMAR SURI CONTRACTOR

ROYAL ENGINEERS AND CONTRACTORS

JAY AAR ENTERPRISES