civil work

Amount

Removing Doors and Windows (Steel or wood) with chowkhats by making recesses in walls when the wall is not to be dismantled. (L/R) Doors of area 3 sqm and below. (Ref. 8.26(a)

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (T/R) (Ref-17.101)

Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate z sections and other sections conforming to Is: 733 and IS : 1285 of Jindal, Hindalco, Mahavir or equivalent make approved by Engineer in Charge , fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC Plug/neoprene felt etc. aluminum sections shall be smooth, rust free, straight, mitered and jointed mechanically wherever required including cleat angle, aluminum snap beading for glazing/paneling, C.P.brass/stainless steel screws, all complete as per architectural drawings and the directions of Engineer-In- Charge. (Glazing and paneling to be paid for separately) For fixed portion and chawkhats: (T/R) (Ref- 17.45 a)

For shutters of doors, windows & ventilators including providing and fixing hinges/pivots and labour for fixing of fittings wherever required including the cost of PVC Plug / neoprene gasket required (T/R) (Ref - 17..45 b)

Providing Polyester Powder coating 50micron any coloured specified to alumnum section of various sizes including carriage of material from market to workshop & workshop to site of work. (T/R) (Ref-18.48)

Providing and fixing glazing in aluminum door, window, ventilator shutters and partitions etc. with PVC Plug/ neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminum snap beading shall be paid in basic item)Float glass panes of 5 mm thickness (T/R) (Ref-17.47)

Cost of aluminum fittings complete for doors, windows such as tower bolts, handles,Stoppers and screw etc. for these fittings (Excluding sliding bolt)For shutter area above 0.50 sqm (T/R) (Ref-17.23(ii)

Providing and fixing aluminum sliding door bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete :250mm x 16mm (T/R) (Ref-17.49b)

Providing and fixing bright finished brass 100 mm mortise latch and lock with 6 levers and a pair of lever handles with necessary screws etc. complete (best make of approved quality). (T/R) (Ref-17.22(iv)

12.5 mm thick cement plaster 1:5 (T/R) (Ref-15.10)

Providing & fixing ACP Sheets of various thickness High Class ISI marked complete in all respect as per the directions of Engineer-in-charge.4mm thick ACP Sheet (T/R) Ref-17.97 (ii)

Removing Doors and Windows (Steel or wood) with chowkhats by making recesses in walls when the wall is not to be dismantled.. Doors of area 3 sqm and below. (L/R) (Ref-8.26 (a)

Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate z sections and other sections conforming to Is: 733 and IS : 1285 of Jindal, Hindalco, Mahavir or equivalent make approved by Engineer in Charge , fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC Plug/neoprene felt etc. aluminum sections shall be smooth, rust free, straight, mitered and jointed mechanically wherever required including cleat angle, aluminum snap beading for glazing/paneling, C.P.brass/stainless steel screws, all complete as per architectural drawings and the directions of Engineer-In- Charge. (Glazing and paneling to be paid for separately), For fixed portion and chawkhats (T/R) (Ref-17.45 (a)

For shutters of doors, windows & ventilators including providing and fixing hinges/pivots and labour for fixing of fittings wherever required including the cost of PVC Plug / neoprene gasket required (T/R) (Ref-17.45 (b)

Providing Polyester Powder coating 50micron any coloured specified to alumnum section of various sizes including carriage of material from market to workshop & workshop to site of work. (T/R) (Ref-18.48)

Providing and fixing aluminum Wire Mesh including cost of necessary fittings i.e. screws,u Type Beading etc. complete (T/R) (Ref-17.96)

Providing and fixing glazing in aluminum door, window, ventilator shutters and partitions etc. with PVC Plug/ neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminum snap beading shall be paid in basic item)Float glass panes of 5 mm thickness (T/R) (Ref-17.47)

Cost of aluminum fittings complete for doors, windows such as tower bolts, handles,Stoppers and screw etc. for these fittings (Excluding sliding bolt)For shutter area above 0.50 sqm (T/R) (Ref-17.23(ii)

Providing and fixing hydraulic door closer ISI mark with necessary screw etc. complete I.S.I Designation No. III (size of door 851mm to 1000mm) (T/R) (Ref-17.43©

Providing and fixing aluminum sliding door bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete :250mm x 16mm (T/R) (Ref-17.49b)

12.5 mm thick cement plaster 1:5 (T/R) (Ref-15.10)

Removing Doors and Windows (Steel or wood) with chowkhats by making recesses in walls when the wall is not to be dismantled. Doors of area 3 sqm and below. (L/R) (Ref-8.26 (a)

Dismantling Sanitary fixtures such as Eurpoean/Indian/Orissa W.C., PVC / China ware cistern, Wash Hand Basin, Urinal Pot, Sinks and CP Fittings and disposal of dismantled material within a distance of 100 Mtr. complete in all respect as required by Engineer-in-Charge. Eurpoean/Indian/Orissa W.C. (L/R) ( Ref-30.88(a)

b) PVC / China Ware Cistern ( Ref-30.88(b)

c) Wash Hand Basin / Urinal Pot ( Ref-30.88©

d) CP Bib Cock/Angle Cock/Stop Cock/Shower/Bottle Trap ( Ref-30.88€

e) Bathroom Assessories such as Soap Dish, Towel Rail, Towel Ring, Towel Bracket, Mirror, Toilet Paper Holder, Seat Cover, Jet Pressure and all other accessories. ( Ref-30.88(g)

Dismantling of wall tiles at any floor of the building, laid in cement mortar including scraping of cement plaster and disposal of malba at a suitable place within a distance of 100 Mtrs of the complex complete in all respect. (L/R) (Ref-30.94)

Dismantling of floor tiles at any floor of the building, laid in cement mortar including dismantling of cement concrete base and disposal of malba at a suitable place within a distance of 100 Mtrs of the complex complete in all respect (L/R) (Ref-30.95)

Providing and laying Anti skid Ceramic floor tiles of size 300x300 mm x 10 mm thick of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on flooring skirting and dado in 12.5mm thick cement plaster 1:3 in base and jointed with @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., completewhite cement slurry in joints including corners angles and beading. (T/R) (Ref-14.72)

Providing and fixing 1st quality ceramicglazed wall tiles Matt/Semi Matt/Glosy/Highly Gloss finish/Highlighter/emboss conforming to IS : 15622 (thickness to be specified by the manufacture of approved make in all colours, shades except burgundy, bottle green, black of size 250 x 330 mm & 300x300mm as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:4 (1 cement: 4 fine sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. (T/R) (Ref-14.126)

Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate z sections and other sections conforming to Is: 733 and IS : 1285 of Jindal, Hindalco, Mahavir or equivalent make approved by Engineer in Charge , fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC Plug/neoprene felt etc. aluminum sections shall be smooth, rust free, straight, mitered and jointed mechanically wherever required including cleat angle, aluminum snap beading for glazing/paneling, C.P.brass/stainless steel screws, all complete as per architectural drawings and the directions of Engineer-In- Charge. (Glazing and paneling to be paid for separately) : For fixed portion and chawkhats (T/R) (Ref-17.45 (a)

For shutters of doors, windows & ventilators including providing and fixing hinges/pivots and labour for fixing of fittings wherever required including the cost of PVC Plug / neoprene gasket required (T/R) (Ref-17.45 (b)

Providing Polyester Powder coating 50micron any coloured specified to alumnum section of various sizes including carriage of material from market to workshop & workshop to site of work. (T/R) (Ref-18.48)

Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS:12823 Gradel Typell, in paneling fixed in aluminum doors, windows shutter sand partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and direction so fEngineer-In-Charge.Pre laminated particle boardwith decorative lamination on Both side. (T/R) (Ref-17.46 (ii)

Cost of aluminum fittings complete for doors, windows such as tower bolts, handles,Stoppers and screw etc. for these fittings (Excluding sliding bolt)For shutter area above 0.50 sqm (T/R) (Ref-17.23(ii)

Providing and fixing hydraulic door closer ISI mark with necessary screw etc. complete I.S.I Designation No. III (size of door 851mm to 1000mm) (T/R) (Ref-17.43( c )

Providing and fixing aluminum sliding door bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete :250mm x 16mm (T/R) (Ref-17.49b)

12.5 mm thick cement plaster 1:5 (T/R) (Ref-15.10)

Providing and fixing in position Chinaware extended wall mounted E. W.C. type suite (size 66 x 46 x 77.5 cm ) with P trap or S trap of approved make (to the approval of the Engineer-in-charge) with or without 10 ltr. chinaware matching flushing cistern and seat cover complete in all respect and to the entire satisfaction of Engineer-in-charge.Chinaware extended wall mounted E W.C. with matching chinaware cistern and seat cover complete in all respect.(T/R) (Ref-30.5(a)

Providing and fixing in position vitreous Chinaware white lIndian make large flat back or angular lipped front urinal 375 x 390 x 590 mm of approved make (to the approval of the Engineer-in-charge) consisting of C.P. brass Urinal waste Coupling dome type 32mm outer length 75 mm , C.P. brass Urinal Spreader Ocular-Regular and C.P. brass tube connection 300 mm long complete. (T/R) (Ref-30.16)

Providing and fixing P.V.C Waste Pipe Collapsiable 32mm complete in all respect.(T/R) (Ref-30.20)

Providing and fixing in position vitreous chinaware white lavatory suites of approved make (to the approval of Engineer-in-charge) consisting of C.P. brass waste 32mm dia with one C.P. brass pillar tap including Rack Bolt Screw Pair 115mm long complete in all respect.Size 550 mm x 400 mm x 815 mm (T/R) (Ref-30.32 ii)

Providing and fixing in position C.P. brass overhead shower 1 flow with shower arm with 15mm i/d inlet of approved make (to the approval of Engineer-in-charge) complete in all respect. (T/R) (Ref-30.56( a )

Providing and fixing in position paper holders of approved make (to the approval of Engineer in- charge ) fixed in to wall with C.P brass screws complete in all respect.C.P. brass toilet paper holder (T/R) (Ref-30.57(a)

Providing and fixing in position towel rails / ring of approved make (to the approval of Engineer-in-charge ) fixed in with rawl plugs embedded in walls with brass screws complete in all respect.C.P. brass towel Rails size 15mm dia 610mm long (T/R) (Ref-30.58(a)

Providing and fixing in position C.P. Acrylic shelf with C.P.bracket and guard rails of approved make (to the approval of Engineer-incharge ) fixed in with rawl plugs and C.P brass screws complete in all respect.CP brass Acrylic Shelf size 560mmx130mm (T/R) (Ref-30.59(a)

Providing and fixing in position C.P. brass soap dish of approved make (to the approval of Engineer-in-charge ) fixed into wall with rawl plugs and C.P brass screws complete in all respect. (T/R) (Ref-30.60)

Providing & Fixing in position 5mm thick bevelled edge mirror of superior glass (of approved make) complete with 4mm thick hard board backing fixed in with rawl plugs 50mm, C.P. brass screws and washers and S/S Studs on top complete in all respect (as required by the Engineer-in- Charge)Size 600mmx450mm (T/R) (Ref-30.61(a)

Providing & Fixing in postion 15 mm i/d bib cock of approved make (to the approval of Engineer-in-charge )complete in all respect. (T/R) (Ref-30.65 (A) (i) C.P. brass Bib cock long nose/ long body foam flow without flange.

-do- C.P. brass Bib cock foam flow without flange (Ref-30.65 (A-ii)

Providing & Fixing in postion stop cock/ angle valve of approved make (to the approval of Engineer-in-charge ) complete in all respect. a) C.P.brass 15mm stop cock Male and female end (T/R) (Ref-30.66 (a)

-do- C.P.brass 15mm Concealed stop cock with flange. (Ref-30.66 (b)

Providing & fixing in position PVC flexible tube connection of approved make (to the approval of Engineer-in-charge ) complete in all respect .PVC tube connection of size 15 mm x 600 mm with PTMT nut (T/R) (Ref-30.72h)

Providing and fixing in position singel socket SWR UPVC soil waste or antisyphonage pipes as per IS 13592 of E.D.C manufacture or of any other reputed firm including cutting, jointing, wastage, but excluding cost of jointing. Single Socket Type B 110mm o/d SWR UPVC pipe lines laid complete (T/R) (Ref-30.74 iii B(b)

Providing and fixing in position SS Grating with frame of approved make (to the approval of engineer in charge) complete in all respects. (T/R) (Ref-30.80)

Providing and fixing in position SWR UPVC special for soil waste vent or anti syphonage pipes as per as per IS - 14735 including cutting and wastage etc. cutting holes in walls roofs or floors etc. and making good to its original condition but excluding cost of lead joining.For 110mm o/d pipes (T/R) (Ref-30.81 (iii)B iii) Single Tee

-do- Door Elbow 90 Degree (All side socketed) (Ref-30.81 (iii)B-iv)

Vent Cowls (Ref-30.81 (iii)B-vi)

P Trap/Floor Trap 110mm x 110mm (Ref-30.81 (iii)B-ix)

Providing ,laying, jointing, fixing and testing ISI Marked G.I. Pipe (as per IS 1239) BClass including cost of specials (such as tees, bends, sockets, elbows etc.) ,painting with anti corrosive bitumastic paint, testing, cutting, threading Inside building complete.15mm i/d (T/R) (Ref-28.35(a)

Removing Doors and Windows (Steel or wood) with chowkhats by making recesses in walls when the wall is not to be dismantled. Doors of area 3 sqm and below. (L/R) (Ref-8.26 (a)

Providing & Fixing of PVC panelling upto 6mm thick on walls complete in all respect to the satisfaction of engineer in charge (NSI) (T/R)

Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate z sections and other sections conforming to Is: 733 and IS : 1285 of Jindal, Hindalco, Mahavir or equivalent make approved by Engineer in Charge , fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC Plug/neoprene felt etc. aluminum sections shall be smooth, rust free, straight, mitered and jointed mechanically wherever required including cleat angle, aluminum snap beading for glazing/paneling, C.P.brass/stainless steel screws, all complete as per architectural drawings and the directions of Engineer-In- Charge. (Glazing and paneling to be paid for separately) : (T/R) (Ref-17.45(a) a ) For fixed portion and chawkhats

For shutters of doors, windows & ventilators including providing and fixing hinges/pivots and labour for fixing of fittings wherever required including the cost of PVC Plug / neoprene gasket required (T/R) (Ref-17.45 (b)

Providing Polyester Powder coating 50micron any coloured specified to alumnum section of various sizes including carriage of material from market to workshop & workshop to site of work. (T/R) (Ref-18.48)

Providing and fixing glazing in aluminum door, window, ventilator shutters and partitions etc. with PVC Plug/ neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminum snap beading shall be paid in basic item)Float glass panes of 5 mm thickness (T/R) (Ref-17.47)

Cost of aluminum fittings complete for doors, windows such as tower bolts, handles,Stoppers and screw etc. for these fittings (Excluding sliding bolt)For shutter area above 0.50 sqm (T/R) (Ref-17.23(ii)

12.5 mm thick cement plaster 1:5 (T/R) (Ref-15.10)

RECESSED HDPE PIPE WIRING SYSTEM WITH MODULAR SWITCHES: Wiring in PVC insulated copper conductor single core FR cable (ISI marked), overall 1.5sq. mm, 1100volts grade to be laid in HDPE electrical conduit pipe 20mm/25mm dia. ISI Marked, recessed in wall etc., complete with powder coated/anodized concealed metal boxes (1.6mm thick with Brass lugs) required for suitable number of modules (Modular accessories) for having Step type electronic fan regulators (two module) 100watts, bell push, 6Amp. 2/3 universal socket (shuttered), 6/20Amp. combined/ universal Socket (shuttered), 6/10Amp. Switches, 16/20Amp. switches with indicator etc. and covered with Frame Plate etc., PVC connector (For Fan Box and Call Bell), PVC Bush, Steel Hooks, Sheet metal fan box (1.6mm thick shape hexagonal), CI Circular junction Boxes (Four way 1½" deep for walls and 3" deep for ceiling), bonding to earth with PVC insulated copper conductor single core FR cable (ISI marked) 1sq. mm, 1100volts grade (For 6Amp. wall socket & plug control point) and other petty material etc., including the cost of above material, cutting and filling up of chases (with finishing the surface):- Wiring fan point (Without fan box) (T/R) (Ref-34.03 (i) a)

Wiring light point (Ref-34.03 (ii)

Wiring call-bell point (Ref-34.03 (iii)

Wiring 6Amp. Plug control comprising wall socket point (Ref-34.03 (v)

Wiring 16/20Amp. power plug control point (Ref-34.03 (vi)

Rajat Soni (BID ID -897218)

amandeep kalia govt contractor (BID ID -897204)