Special repairs to ORs living building No HT 136 MP PL HT 156 MT shed TH 143 QM office and TH 158 Guard Room of 47 FD Wksp Coy EME under GE North Ambala Cantt

Amount

SCHEDULE A PART I (B/R WORKS)

Demolition of cement concrete (unrenforced) in ground floors and pavings not exceeding 15cm thickness (below or above ground level) complete all as specified and directed.

Material and labour for PCC 1:2:4 type B-0 (using 12.5 mm graded mechanically crushed stone aggregates), 25mm thick, as in sub base to floor/bedding layer to floor etc., finished rough to receive topping layer complete all as specified and directed.

Material and labour for PCC 1:3:6 type C-2 (using 40 mm graded mechanically crushed stone aggregate), 50mm thick, as in plinth protection/PCC path and paving, laid in panels of area not exceeding 1.20 sqm with 12mm wide joints filled with mastic (using bitumen and sand mixture applied hot in the ratio of 1:3 by weight) formed at the end of each panel and change in direction of plinth protection/PCC Path and paving and finishing the top surface even and smooth without using extra cement complete all as specified and as directed.

Material and labour for premium quality, joint free, anti skid porcelain tiles, area of each tile exceeding 0.18 sqm and not exceeding 0.36 sqm and 7 to 8 mm thick, laid in floor over and including cement screed bed 15mm thick in cement mortar (1:4) and set and jointed in neat cement slurry and pointed in white or coloured cement to match the tile complete all as specified and directed.

Material and labour for premium quality, coloured ceramic tiles (Square/rectangular), area of each tile exceeding 0.11 sqm and not exceeding 0.18 sqm and 7 to 8 mm thick, laid in vertical surfaces such as skirting, dado and riser to steps etc. over and including cement screed bed 10mm thick in cement mortar (1:4) and set and jointed in neat cement slurry and pointed in white or coloured cement to match the tile complete all as specified and directed.

Taking down cement or cement lime plaster, of any description, on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and as directed.

Material and labour for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6, finished even and smooth without extra cement all as specified and as directed.

Material and labour for rendering, 15 mm thick, in cement mortar 1:4, mixed with water proofing compound @ 2% by weight of cement or as per manufacturer’s instructions, on fair faces of brick work or concrete surfaces of any description finished even and smooth without using extra cement complete all as specified and as directed. Note: Supply only integral water proofing shall be measured and paid separately.

Supply only integral water proofing compound complete all as specified and as directed.

Material and labour for preparation of newly plastered wall surfaces and applying two coats of cement base paint complete all as specified and as directed.

Material and labour for preperation of newly plastered surfaces of walls and applying two coats of oil bound distemper over a coat of chalk whitening over 2mm thick wall putty complete all as specified and as directed.

Material and labour for preparation of newly plastered surfaces of wall and applying three coats of white wash complete all as specified and as directed.

Material and labour for preparation of old plastered surfaces of wall and applying two coats of white wash complete all as specified and as directed.

Dismantling of asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings or wall cladding and removal of dismantled material outside defence land complete all as specified and directed.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed.

Dismantling of steel framed trusses not exceeding 10m span complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Supply and fixing of fabricated rolled mild steel sections as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats etc, conforming to quality-A, Gde E-250, Fe-410-W welded or rivetted complete all as specified and as directed

Material and labour for rolled mild steel plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to quality-B, Gde E-250, Fe-410-W welded or rivetted complete all as specified and as directed.

Supply and fixing of mild steel bolts of dia exceeding 12 mm and not exceeding 20mm, purpose made, with hexagonal or square head one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut. exceeding 30cm long complete all as specified and as directed.

Supply and fixing of pre-painted galvalume red colour, aluminuim zinc coating, GI based corrugated (SINOSUIDAL PATTERN) steel sheet, 0.50mm thick, conforming to IS-15961, of any colour, having tensile strength of 550 MPa, as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed. Note- The sheets shall have super durable polyester quality paint of approved colour, 150 gm/sqm total on both sides, suitable for exterior application conforming to IS-15965.

Supply and fixing of pre-painted galvalume red colour, aluminuim zinc coating, GI based Plain steel sheet, 0.50mm thick, of any colour, having tensile strength of 550 MPa, as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed. Note- The sheets shall have super durable polyester quality paint of approved colour, 150 gm/sqm total on both sides, suitable for exterior application conforming to IS-15965.

Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insula tion boardsl slabsl blankets, any thickness, including cover fillets, aluminium frame of any description complete all as specified and directed.

Dismantling timber scantlings 40 sq. cm and over in section, in any position, framed work complete all as specified and directed.

Dismantling timber scantlings under 40 sq. cm in section, in any position, framed work, as in fillets, rails, posts, rafters, purlins, etc. complete all as specified and directed.

Supply and fixing for Galvanised powder coated snap grid ceiling consisting of cross and tee section of soze 24mm x 38mm x 0.30mm and wall grid angle 15mm x 15mm including 12mm thick triangular cut mineral fibre board of size 600 x 600mm. The snap grid frame shall fixeed to ceiling with supporting consisting of 4mm dia GI wire including clip or with necessary nuts and bolts as per manufacturer instructions complete all as specified and directed.

Taking down chowkats or frames with shutter, area not exceeding 1.50 Square metre (w/o taking off shutters from frames) and removing from site, including cutting holes in wall/concrete for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces in CM (1:3) and finishing the surfaces to match with existing finish complete all as specified and directed.

Taking down chowkats or frames with shutter, area exceeding 1.50 Square metre and not exceeding 4.00 Square metre (without taking off shutters from frame) and removing from site, including cutting holes in wall/concrete for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces in CM (1:3) and finishing the surfaces to match with existing finish complete all as specified and directed.

Supply and fixing of pressed steel frames for doors of size 105x60mm, 1mm thick, with one or more rebates including, hold fasts of 25mm x 4mm FI, 25mm long, 6 Nos in each chowkhat, necessary lugs, 4 Nos 100 mm butt hinges medium weight, cold rolled, welded for each frame, lock strike plate, including sanding, tarring backs of chowkhats, PCC 1:3:6 type C-0 filling as in back of chowkhats, 2 Nos 12 mm dia tie bars at the bottom of frame and one shop coat of red oxide primer etc complete all as specified and as directed.

Supply and fixing of pressed steel frames for doors of size 125x60mm, 1mm thick, with one or more rebates including, hold fasts of 25mm x 4mm FI, 25mm long, 6 Nos in each chowkhat, necessary lugs, 4 Nos 100 mm butt hinges medium weight, cold rolled, welded for each frame, lock strike plate, including sanding, tarring backs of chowkhats, PCC 1:3:6 type C-0 filling in frame and for holdfast, 2 Nos 12 mm dia tie bars at the bottom of frame and one shop coat of red oxide primer etc complete all as specified and as directed.

Material and labour for second class hard wood glazed and skeleton shutters, 35mm thick, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, elc.;sizesof me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats all as specified and directed.

Material and labour for Iind class HW 35mm thick plain framed panelled shutter (two panel) with lock rail and panel of 9mm BWP commercial ply of 12mm veneered particle board with commercial veneering on both face. The size of rail and style as per IS:1003 (Part-1) kiln seasoned and chemically pressure treated complete all as specified and directed.

Supply and fixing of galvanised mild steel wire cloth, but 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed.

Supply and fixing of steel window box type, with side hung shutters, using ERW hollow 'P' section, factory made, comprising double frame for and including gauged and glazed skeleton shutter, 30mm thick, jointed internally with flat iron 25x3mm complete including hinges, handle, tower bolts, stops, lugs etc. all as shown on drawing No. TD-219(c) sheet 1/3 to 3/3 and TD-220 sheet 1/3 to 3/3 as applicable complete all as specified and as directed. Note: (i) For the purpose of measurement and payment double shutter both glazed and gauzed with frame shall be considered as one unit. (ii) Unit rate quoted against this item shall also include the iron mongery and grill 8 mm square bar irrespective of whatever shown on drawings and one shop coat of zinc chromate primer. (iii) Glazing, wire mesh and painting shall be measured and paid for separately.

Supply and fixing of sheet glass, 3mm thick, ordinary quality and glazing with oil putty in squares not exceeding 0.5 sqm. in each pane complete all as specified and directed.

Supply and fixing of aluminium handle, 150 mm long, cast type, anodized, ISI Marked complete, all as specified and as directed.

Supply and fixing of aluminium anodised, 150mm long, barrel tower bolts of extruded section and fixed complete all as specified and as directed.

Supply and fixing of aluminium sliding door bolts, 300mm long, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and as directed.

Material and labour for preparing new or previously untreated wood and wood based surfaces of any description not otherwise described over 10cm width or girth and applying two coats of approved colour synthetic enamel paint over one coat of pink primer complete all as specified and directed.

Material and labour for preparation of new steel surfaces, of any description not otherwise described, over 10 cm width or girth and applying two coats of approved colour synthetic enamel paint, over a coat of red oxide zinc crome primer complete all as specified and as directed.

Demolition of brickwork or stone masonry, built in cement mortar, including all quoins, arches, pillars etc, complete all as specified and as directed.

Material and labour for brick work with sub class ‘B’ bricks old size , burnt, straight or curved on plan exceeding 6 metre mean radius built in cement mortar (1:6) complete all as specified .

All as above Item No 1.41 but except bricks complete all as specified and as directed. Note: Old serviceable bricks as obtained from serial item No 1.40 hereinbefore shall be reused after cleaning the tiles. The rate quoted shall include for cleaning the tiles also.

Supply and fixing in repairs, Mild steel powder coated decorative curtain rod, 20mm dia and fixing with decorative brackets, stop rollers and finials at the end complete all as specified and directed.

Material and labour for PCC 1:2:4 type B-2 (using 40 mm graded mechanically crushed stone aggregate), 150mm thick, as in floor, laid in alernate bays forming 12mm wide expansion gaps and finishing the top surface even and smooth without using extra cement complete all as specified and as directed.

Material and labour for forming 12mm thick expansion joints, filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade ' A' for 150mm thick concrete slab complete all as specified and directed.

SCHEDULE A PART II (E/M WORKS)

Taking down carefully any type of point wiring (light, fan, socket or power) complete with fittings such as switches, ceiling roses, pendants, regulators, sockets, tube light fittings with all accessories etc., and/or drawing out from existing conduit/batten and removal of materials from site and making good the disturbed surfaces of wall, floors, ceiling etc to match with the existing surfaces with matching OBD/White wash/Distemper complete all as specified and as directed.

Material and labour for concealed point wiring using approved colour coding as per IS, with multi stranded copper conductor 1.5 sqmm (Nominal area), single core, FRLS-H, 1100 volts, ISI marked, PVC insulated and unsheathed stranded cable drawn through and including non metallic, medium grade PVC concealed conduit not less than 25 to 32mm dia and its fittings including all tees, bell mouth pieces and fixing accessories such as couplers, saddlers, pipe hooks etc, PVC junction boxes, ISI marked including mild steel sunken boxes, made out of 1.6mm thick mild steel sheet conforming to IS-5139 (part-I)of 1969 and IS-14772-2000, with earth dolly with suitable size lugs, coated with two coats of anti corrosive paint over a coat of red oxide primer both internally and externally, covered with modular cover plate over sunken box for housing of switches, socket outlets, fan regulators etc., with brass screws and washers, including 1.5 sqmm single core PVC insulated and unsheathed FRLS-H cable, 1100 volt grade with multi stranded copper conductor, green colour, ISI marked, as earth continuity conductor upto common earth and connecting to common earth dolly with suitable size of lugs complete all as specified and directed for one light point (for tube lights and building security lights)/ fan point (for ceiling fans) and each point controlled by one switch complete all as specified and as directed. Notes :- (i) Switch, socket and fan regulators to be measured and paid for separately. (ii) PVC Conduit conforming to IS 9537 part I & III. (iii) All chases shall be cut by chase cutter only. Make of PVC Conduit- Finolex/Polycab/Kalinga Premium/Surya/Plaza/Dplast Make of PVC wire- Finolex/Polycab/Havells/Plaza

Description all as per Srl item No.02 here in before but for one 3 pin socket outlet point 5 Amp on Independent board.

Description all as per Srl item No.02 here in before but for one 3 pin socket outlet point 5 Amp on same board.

Description all as per serial item No.02 above All as per the description of Serial Item No 2.02 above, but with 4 Sqmm PVC, FRLS-H, unsheathed, multistranded cable, for one socket point 15 Amps, 1100 volts grade, ISI marked, including 4 Sq mm size, green colour, PVC insulated FRLS-H, continuous copper earth wire and connected to common earth dolly complete all as specified and as directed. Note- Switch, Socket shall be measured and paid separately and Steel junction boxes shall be used wherever junction boxes are to be fitted.

Supply and fixing of switch, modular, 6 Amp, one way, one module, 230 volt complete all as specified and as directed. Make: Anchor/Fine/SSK.

Supply and fixing of switch, modular, 16 Amps, one way, one module, 230 volt, complete all as specified and directed. Make: Anchor/Fine/SSK.

Supply and fixing of socket, modular, 2/3 pin, 5 Amps, one way, two module, 230 volts complete all as specified and directed. Make: Anchor/Fine/SSK.

Supply and fixing of socket, modular, 2/3 pin, 6/16 Amps, combined, one way, two module, 230 volts complete all as specified and as directed. Make: Anchor/Fine/SSK.

Supply and fixing of electronic fan regulator, modular, 100 watt, two module suitable for ceiling fan, any type/make/sweep complete all as specified and as directed. Make: CONA/ROMA/PLAZA.

Supply and fixing of ceiling rose surface bakelite 65x50mm, two to three terminals complete all as specified and as directed. Make: SSK/Anchor/Fine

Supply and fixing of MCB, single pole, 240 volts, 50Hz, breaking capacity 10KA, 'C' curve, 6 to 40 Amps, ISI marked including taking down and removal of old unserviceable MCB of any capacity and type complete all as specified and as directed. Make- Siemens/Schenider Acti 9/Hager Nevello Plus/Legrand

Supply, insatallation, commissioning and testing of distibution board for MCBs, SPN, 8 way, acrylic double door, IP 43, as per IS 8623, 240 volts, with and including 200 amps fully insulated copper bus bar fixed on wall duly grouted in solid block wall with and including copper lugs/thimbles duly crimped for connection including taking down and removal of old unserviceable MCB DB of any capacity, size and type complete all as specified and directed. Make- Siemens/Schenider Acti 9/Hager Nevello Plus/Legrand

Supply and fixing of RCBO, 40 Amps capacity , 2 module, 300mA (HI immunity) sensitivity, 230 volts, 50 Hz, ISI marked including taking down and removal of old unserviceable RCBO of any capacity and type complete all as specified and directed. Make- Siemens/Schenider Acti 9/Hager Nevello Plus/Legrand

Material and labour for sub main wiring with two single core FRLS (Fire Retardant Low Smoke), PVC insulated unsheathed copper conductor cable, 6 sqmm, drawn in and including rigid non metallic PVC conduit, medium grade, 25 mm dia, concealed on wall or ceiling, with accessories with and including one additional 6 sqmm, PVC insulated, stranded copper conductor, FRLS, green colour for earth continuity conductor including taking down old unserviceable sub main wiring of any type and making good the disturbed surface complete all as specified and as directed. Note- Three runs of 6.0 sqmm cable and one run of concealed conduct shall be measured as one unit. Cable make: Plaza/Polycab/RR.

Supply and fixing of indoor decorative surface mounting LED tube light fitting, batten type, with poal diffuser, high efficient aluminium housing body in CRCA body suitable for LED tube, high efficient, AC 220-240 volts, 50 Hz with and including 18/20 watt LED tube rod luminaries (warm/cool as per site requirement), environment friendly, high efficient, T8 with aluminium extrusion, heat sink and connecting with copper conductor flexible cable of size 0.50 Sqmm from ceiling rose to connector of the light fitting including disconnecting and taking down of existing light fitting and removal complete all as specified and as directed. Make: Havells Cat Part (Fitting)- REGAL BATENT8 4TPO 1x22WSSBSWH, Tube: CRYSTAL 1213 T8DSTL 20WLED865SGLASS, Wipro Cat Part (Fitting) No-WI0921208, Tube: LC13181, Philips Cat Part (Fitting) No--TMC501 1xT-LED 22W P3241, Tube: 20W865 T8 INDI-2100Lm

Supply and fixing of LED security light luminaire 45 watt , made up of die cast aluminum housing with black epoxy powder coatingwith cover heat resistant glass, safety input voltage range 170 to 270 Volts, IP66 protection, including service brackets of GI pipe 32mm bore medium grade of length 0.90 metre with MS clamps, bolts, nuts and washers and suitable reducer for connecting to GI pipe as required at site and making all required electrical connections using cable including disconnecting and taking down existing light fitting and removal complete all as specified and as directed. Make: Havells Cat Part No ENDURAPEARLNEOSL40WLED757PASYTOPC, Wipro Cat Part No LRO2-45I-XXX-57-XX, Philips Cat Part No BRP409LED 040CWHOMRFGSIPSUGR

Material and labour for earthing complete with galvanised steel earth plate 600 x 600 x 6mm buried directly in ground vertically to a depth not less than 2.25 metre below normal ground level with top edge of the earth plate at a depth not less than 1.5 metre below ground level connected to and including GI earth strip of size 25mm x 4 mm as earth lead connected with equipment by means of nuts, bolts, washers etc protected by GI pipe 40mm bore (medium grade) and connected to earthing test point and earth dolly as directed and as specified and all shown in electrical plate No.3 of SSR Part-I 2009 including excavation and earth work in any type of soil, PCC (1:3:6) type C1 in chamber, pre cast RCC slab 400 x 400 x 50mm thick in cement concrete (1:2:4) type B1, reinforced with with 8mm dia TMT bars @ 15cm C/C both ways with one handle for lifting made out of 8mm dia bar with cast iron frame, funnel, with wire mesh, 20mm bore medium grade GI watering pipe, charcoal or coke and salt in alternate layers of 15cm depth, lugs, test point etc including taking down existing light fitting and removal and earth testing on completion complete all as specified and as directed.

Note:- Amount of credit of Rs. 31,931.00 for retrieved materials is mentioned in Schedule of Credit Page Nos.101 & 102 of tender documents in pdf form which will be deducted offline while acceptance of tender.

Swami Enterprises

V K Constructive Builders

M/S SHANTI CONSTRUCTION

MAYANK ENTERPRISES

s.v.builders