PROVISION OF NEW MAIN GATE WITH SECURITY POST INCLUDING CONNECTING ROAD,PATH AND BOUNDARY WALL AT MEGHADRIPETA COLONY AND DEMOLITION RECONSTRUCTION OF WATCH TOWER No. 03 AT MO V UNDER GE ND, VISAKHAPATNAM

Amount

Demolition of Plain Cement Concrete in ground floors and Pavings not exceeding 15cm thick [below or above ground level] and removing rubbish to a distance exceeding 1.5 KM and not exceeding 5.00 KM complete all as specified and as directed.

Demolition of Reinforced Cement Concrete [reinforcement cut as required to facilitate demolition] in Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work and removing rubbish to a distance exceeding 1.50 KM and not exceeding 5.00 KM complete all as specified and as directed.

Demolition of Reinforced Cement Concrete [reinforcement cut as required to facilitate demolition] of any description and in any position not otherwise specifically provided for and removing rubbish to a distance exceeding 1.50 KM and not exceeding 5.00 KM complete all as specified and as directed.

Demolition of Brick / Stone Masonry built in Cement Mortar including all quoins arches pillars etc complete all as specified and as directed.

Taking down Chowkats or frames with shutters [without taking off shutter from the frame] not exceeding 1.5 Sq.m each complete all as specified and as directed.

Taking down Chowkats or frames with shutters [without taking off shutter from the frame] exceeding 1.5 Sq.m but not exceeding 4.00 Sq.m each complete all as specified and as directed.

Dismantling of Mild Steel or Wrought Iron Work of any description not otherwise provided for complete all as specified and as directed.

Dismantling of Structural Steel work including Doors, Gates etc but excluding framed trusses complete all as specified and as directed.

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in Hard / Dense complete all as specified and as directed.

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in Soft/ Loose complete all as specified and as directed.

Excavation over areas not exceeding 1.5m deep and getting out in Soft / Loose soil complete all as specified and as directed.

Excavation over areas depth exceding 1.5m but not exceeding 3.0m and getting out in Hard/ Dense soil complete all as specified and as directed.

Excavation in trenches not exceeding 1.5m wide and not exceeding 10 Sq.m on plan area and not exceeding 1.5m deep in Soft / Loose soil complete all as specified and as directed.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m deep and getting out in hard / dense soil complete all as specified and as directed.

Excavation in trenches not exceeding 1.5m wide and depth exceding 1.5m but not exceeding 3.0m in Hard/ Dense soil complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick of excavated soil complete all as specified and as directed. Note: A deduction of 10% shall be made from total computed volume of filling to cater in bulk irrespective of machinery used for ramming.

M & L for Sand Filling under floors or in foundations including watering and consolidation complete all as specified and as directed.

M & L for Moorum / Red Bajri filling under Floors or in Pavings laid in layers not exceeding 15 cm thick, spread levelled and rammed / rolled including watering to required level and gradient complete all as specified and as directed. Note: Measurements shall be taken after consolidation of earth and 10% deduction shall be made for payments.

M & L for broken bricks, Hand packed to any thickness at back of walls, over arches etc. and raising or lowering to the required level all as specified and as directed.

M & L for Hardcore of gauge not exceeding 63mm of broken stones or boulders, deposited, spread and levelled in layers not exceeding 15 cm thick watered and rammed to a true surface complete all as specified and as directed.

Removal of excavated material [Soil] to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and as directed.

Removal of excavated material [Soil] to a distance exceeding 250m but not exceeding 500m and depositing where directed complete all as specified and as directed.

M & L for providing pre construction Anti termite treatment for the soil filled under floors/ plinth protection / foundation by applying emulsion at the rate of 5 litres per square metre of surface area complete all as specified and as directed.

M & L for providing pre construction Anti-termite Treatment by Treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall etc. complete all as specified and as directed.

M & L for providing pre construction anti termite treatment for the backfill in contact with foundation by applying emulsion at the rate of 7.5 litres per square metre of vertical surface [Area of the substructure in contact with back fill] complete all as specified and as directed.

M & L for providing and injecting chemical emulsion for Post Constructional Anti - termite Treatment at points of contact of wood work by chemical emulsion [in oil or kerosene based solution] @ 0.5 litre per hole by drilling 6 mm dia holes at a downward angle of 45 degrees at 150 mm centre to centre and sealing the same complete all as specified and as directed.

Boring holes for bored cast–in–situ piles of 450mm dia in any strata except hard rock using Hydraulic Rotary Rig/ DMC method including getting out and disposal of spoil out side MD land complete all as specified and as directed. Notes: [a] Truck mounted Rotary / TMRT / Tubewell boring Machine shall not be used. [b] The rate quoted shall be deemed to be inclusive of the cost for shifting of Rigs as many times as required. [c] The rate quoted shall be deemed to be inclusive of the cost of Bentonite as required at site. [d] All tanks and connected channels made for Bentonite circulation process shall be made good by filling approved moorum including clearing all Bentonite cakes and the rate quoted shall be deemed to include for this provision also.

Boring holes for bored cast–in–situ piles of 450mm dia in hard rock using Hydraulic Rotary Rig/ DMC method including getting out and disposal of spoil out side MD land complete all as specified and as directed. Notes: [a] Truck mounted Rotary / TMRT / Tubewell boring Machine shall not be used. [b] The rate quoted shall be deemed to be inclusive of the cost for shifting of Rigs as many times as required.

Carrying out Initial Load Test on 450mm dia bored cast–in–situ piles as per IS – 2911 [Part – IV] complete all as specified and as directed. Note: The design load of Single pile is 17.50 MT

Carrying out Routine Load Test on 450mm dia bored cast–in–situ piles as per IS – 2911 [Part – IV] complete all as specified and as directed. Note: The design load of Single pile is 17.50 MT

M & L for PCC 1:4:8, Type D-2, using 40mm graded stone aggregate as in Foundation, Fillings, Mass concrete, Footings etc complete all as specified and as directed.

M & L for PCC 1:3:6, Type C-2, using 40mm graded stone aggregate as in Foundation, Fillings, Mass concrete, Footings etc complete all as specified and as directed.

M & L for PCC 1:3:6, Type C-1, using 20 mm graded stone aggregate as in Coping, Bed plate, cill and the like including weathering, slightly rounded or chamfered angles and throating including formwork [straight or curved] complete all as specified and directed.

M & L for PCC 1:2:4, Type B-1, using 20 mm graded stone aggregate as in Coping, Bed plate, cill and the like including weathering, slightly rounded or chamfered angles and throating including formwork [straight or curved] complete all as specified and directed.

M & L for providing Precast Cement Concrete, 1:2:4, Type B1, using 20mm graded stone aggregate as in Cover slabs for drains/ manholes and setting in Cement Mortar 1:4 complete with joints to match complete all as specified and as directed.

Reinforced Cement Concrete, M-30 Grade, Design Mix using 20mm graded stone aggregate as in piles by Tremie pipe method complete all as specified and as directed. Note: [a] Pile shall be casted as mentioned in drawings. However, for payment purpose the length of pile shall be measured up to cut off level only. The unit rate/Lumpsum price quoted shall be deemed to include this aspect. [b] The rate quoted shall be deemed to include Chipping out laitance concrete upto a maximum of 1m above cut off level of pile including disposal of debris up to a distance of 50m complete all as specified and as directed.

M & L for RCC M–30 Design Mix, using 20mm graded stone aggregate as in foundations including rafts, footings, foundation beams, plinth beams, bases for columns, Pile caps, etc. complete all as specified.

M & L for RCC M-30 Design Mix, using 20mm graded stone aggregate as in Columns, pillars, piers, posts and struts etc. complete all as specified.

M & L for RCC M-30 Design Mix, using 20mm graded stone aggregate as in Beams, cantilevers, bressummers, lintels etc. complete all as specified.

M & L for RCC M-30 Design Mix, using 20mm graded stone aggregate as in Slabs supported on walls, beams, columns in floors, roofs, landings, balconies, canopies, deck slabs complete all as specified and as directed.

M & L for RCC M–30 Design Mix, using 20mm graded stone aggregate as in chajjas complete all as specified and as directed.

Supply only integral water proofing compound [ISI marked] of approved make.

M & L for Providing Precast Cement Concrete Solid Block Masonry of 1:3:6, Type C1 using 20mm graded stone aggregate exceeding 100mm width with plain or interlocking joints set in cement mortar 1:6 complete all as specified and as directed.

M & L for brick work with Fly Ash bricks, straight or curved on plan exceeding 6 m mean radius built in Cement Mortar 1:6 complete all as specified and as directed.

M & L for brick work with Fly Ash bricks, straight or curved on plan exceeding 6 m mean radius built in Cement Mortar 1:4 complete all as specified and as directed.

M & L for brick work in half brick thick walls using Fly Ash bricks straight or curved on plan to any radius built in Cement Mortar 1:4 including provision of 2 Nos of 8mm dia bars at every fourth course of brick work complete all as specified and as directed.

Cutting chases, pinning in, making good to facings where required and pointing in Cement Mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting not exceeding 10 cm girth brick walls complete all as specified and as directed.

Use and waste of form work to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits [if any] of foundation and plinth beams, pile caps and similar work, vertical or to batter for rough finished surfaces complete all as specified and as directed. sides of concrete

Use and waste of form work to sides of pillars, posts, struts, piers, columns and stanchions of any shape / cross section for fair finished surfaces of concrete complete all as specified and as directed.

Use and waste of form work to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc, splays between floors and beams and similar works for fair finished surfaces of concrete complete all as specified and as directed.

Use and removal of steel formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick [horizontal or sloping] for fair finished surfaces of concrete complete all as specified and directed.

Use and removal of Steel Formwork to Edges of Concrete Flats, Treads, Breaks in Floors, Window Cills, Concrete Railings, Openings in Concrete Walls, Floor and Roofs and sides of RCC / PCC Bands in Walls, horizontal or sloping and similar work not exceeding 20cm wide for Fair Finished surface of concrete complete all as specified and as directed.

Use and removal of steel formwork to soffits of chajjas including edges for rough finished flat surfaces of concrete complete all as specified and as directed.

S & F Second Class Hard Wood, plain, solid, straight Chowkats and Frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue, pinned at joints complete all as specified and directed.

S & F 35 mm thick Factory made Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed.

S & F 40 mm thick Factory made Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed.

M & L for Powder coated aluminium sections of approved colour for doors, Windows, Ventilators, Partitions, with frames and shutters fully or partly glazed, sliding / openable, with extruded aluminium sections not less than 1.5mm thick and powder coating not less than 60 micron thick including necessary jointing cleats, rubber beading, neoprene packing, aluminium snap beading, screws, powder coated aluminium fittings such as handles, aluminium butt hinges , aluminium tower bolts, stainless steel friction hinges, locking arrangements etc. complete all as specified and as directed. Notes: [a] The size of aluminium extruded sections shall conform to Designation 63400 all shall be as specified in relevant IS code and as specified in MES Schedule Part - I. [b] Panel inserts such as Glass / Particle board / Gauze and grill shall be measured and paid separately at supply only rates. [c] Weight of aluminium sections shall only be accounted for payment purpose. Weight of aluminium Handles, Butt Hinges & Tower Bolts shall not be accounted for payment purpose. [d] The unit rate quoted shall be deemed to include for cost of jointing cleats, glazing clips, rubber beading, neoprene packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as handles, aluminium butt hinges, aluminium tower bolts, stainless steel friction hinges, locking arrangements etc., and fixing only of panel inserts of glass / particle board / gauge and grill.

Supply only 4 mm thick Sheet Glass ordinary quality in squares not exceeding 0.5 Sq.m in each pane complete all as specified and as directed.

Supply only 5 mm thick Sheet Glass ordinary quality in squares exceeding 0.5 Sq.m in each pane complete all as specified and as directed.

Supply only Stainless steel wire mesh with aperture not exceeding 1.40 mm and dia of wire 0.36 mm including supply of tinned tacks or stainless steel wire staples complete all as specified and as directed.

Supply only Powder Coated Aluminium Deco Grill of Model / Design No. DG 104 (7mmx4.2mm), including supply of Powder Coated Aluminium Channel of size 10 X 10 X 1.5mm for fixing Deco Grill complete all as specified and as directed.

Supply only 12mm thick Prelaminated Particle Board, both Side Decorative Choice Lamination, Medium Density, Interior Grade complete all as specified and as directed.

S & F Door Closer of Aluminium body, Hydraulically Regulated, Designation No. 2 universal type, suitable for door shutters of 701 mm to 850 mm in width and of weight between 36 to 60 Kg complete all as specified and as directed.

S & F Solid PVC door frame of size 50mmX47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube in opening of Sintex ot its equivalent make as approved by Accepting Officer complete all as specified and as directed.

S & F Factory made solid panel PVC door shutter 30 mm thick [Style] consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC "C" Channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement supplying & fixing in frame at site as per specification & drawing of Sintex or its equivalent make as approved by Accepting Officer complete all as specified and as directed.

S & F Factory Made Solid PVC Moulded Door Shutter, with Particle Board Core, 28 to 30mm thick [Stiles], with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing shown on Serial Page No. 161 of MES Schedule Part - II complete all as specified and as directed.

S & F PVC Solid Ventilator frame size 50 X 47mm with wall thickness of 5mm made out of extruded 5mm PVC sheet, mitre cut at two comers and jointed with 2 Nos of 150mm long brackets of 15 x 15mm MS square tube, the two vatted profiles are to be reinforced with 19 x 19mm MS square tube, 50% of bottom portion is fixed with 4mm thick pin headed glass and balance 50% of top portion is fixed with 4mm thick pin headed glass louvers and covered with 0.36mm dia stainless steel wire mesh at top portion including necessary PVC beading with screws and 3 Nos 12mm dia MS guard, bars fixed in ventilator frame including two coats of synthetic enamel paint over a coat of red oxide primer to MS guard bars etc all as per specified and directed.

S & F 125 mm size, Butt hinges, Stainless Steel, with SS hinge pin including fixtures complete all as specified and as directed.

S & F 100 mm size, Butt hinges, Stainless Steel, with SS hinge pin including fixtures complete all as specified and as directed.

S & F 75 mm size, Butt hinges, Stainless Steel, with SS hinge pin including fixtures complete all as specified and as directed.

S & F Aluminium anodised barrel Tower Bolt of size 200 mm size of extruded section complete all as specified and as directed.

S & F Aluminium anodised barrel Tower Bolt of size 150 mm size of extruded section complete all as specified and as directed.

S & F Aluminium alloy anodised Sliding Door Bolt with hasp and staple [Bolt Type] of size 150 mm and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed.

S & F Aluminium alloy anodised Sliding Door Bolt with hasp and staple [Bolt Type] of size 250 mm and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed.

S & F Aluminium alloy anodised Sliding Door Bolt with hasp and staple [Bolt Type] of size 300 mm and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed.

S & F 150mm long Aluminium anodised Handle, of extruded section Fabricated Type complete all as specified and as directed.

S & F 125mm long Aluminium anodised Handle,Cast Type complete all as specified and as directed.

S & F Floor Door Stopper of size 150 mm of aluminium alloy body and tongue, anodised, with hard drawn steel spring complete all as specified and as directed.

S & F Decorative type Stainless Steel Curtain Rod of 25 mm dia including PVC rings @ 100 mm centre to centre complete all as specified and as directed.

S & F Decorative type Stainless Steel Brackets with finial suitable for 25mm dia curtain rods complete all as specified and as directed.

S & F brass Wardrobe hook (Singe), 50 to 60mm size complete al as specified and as directed.

S & F Reinforcement using High Strength Corrosion Resistant Deformed TMT Bars of Grade Fe–500D of 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed.

S & F Reinforcement using High Strength Corrosion Resistant Deformed TMT Bars of Grade Fe–500D of 6mm to 8mm dia, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed.

S & F Reinforcement using High Strength Corrosion Resistant Deformed TMT Bars of Grade Fe–500D of 5mm to 10mm dia bars as in stirrups, spacers and binders, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed.

S & F Mild Steel tubes as in Posts, rafters, purlins, railings, etc including special shaped washer etc complete using ERW or induction butt welded tubes confirming to IS - 1161, Grade YST - 240, Medium Grade of any dia complete all as specified and as directed.

S & F Mild Steel work conforming to Fe - 290, Grade E-165 as in Bands, Straps, Supports or Stays for Rainwater, Ventilating Pipes, including Bolts, if required, Hooks [Stay], heavy, for Large Gates, Hook and Pintle Hinges, large Hasps and Staples, Chains, hand made Sliding Bolts, Clamps, Hold Fasts, Wall Ties, Hooks for hanging fans, plain angle cleats for securing purlins to wood trusses or rafters, knee piece inserts, two way and three way straps, plate washers and similar small articles complete all as specified and as directed.

S & F Rolled Mild Steel work confirming to Fe 410-W, Grade-E- 250, Quality-A as in Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc complete, drilled for fixing of steel sheeting or other covering, Doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings [exclusive of steel sheeting or other covering, running rails and guides] and hanging, also fastening and fixing complete all as specified and as directed. Note: The design of Gate and size of steel members shall be as approved by GE.

S & F Three Dimensional Stainless steel Letters [English] made of 0.9mm thick Stainless Steel hollow tubes of Grade AISI 304, standard quality, bright polish finish, Size of each letter 370mm Width x 250mm Depth, any style/ pattern, fixed on Granite Dado / Lining with suitable fixing arrangements with projection from base not less than 25mm, fixed at any height using suitable steel scaffolding and safety measures etc. complete all as specified and as directed.

S & F Stainless steel LOGO made of 2mm thick Stainless Steel sheets of Grade AISI 304, standard quality, bright polish finish, Size of each LOGO exceeding 300mm but not exceeding 600mm, any style/ pattern, fixed on Granite Dado / Lining with suitable fixing arrangements with projection from base not less than 25mm, fixed at any height using suitable steel scaffolding and safety measures etc. complete all as specified and as directed.

S & F Concertina Coil Fencing with Razor punched barb tape Concertina Coil made from High Tensile Spring Steel, High Carbon Wire conforming to IS – 4454 [Part – 1], of Grade –SM duly Hot Dipped Galvanised, 600mm dia, 10 Metre openable length, with Galvanised coating and Punched Tape material as per IS – 513, having 50 Nos Rounds per 6 Metre length [before stretching], having medium barbs [Barb length 24±1mm, Pitch between two barbs 35±1mm], Spring Core Wire [2.5 mm thick] of high tensile strength of 165 Kg / Sq.mm with tape [0.52mm thick] and weight 43.478 Grams / Metre and fixing to “Y” or Trapezoidal shaped angle iron brackets placed at 2.00m to 3.00m apart and with 6/9 horizontal RBT [Reinforced Barbed Tape] Wire, Stud tied with GI Staples and GI Clips to retain horizontal, including necessary bolts and coating with Px Compound [Anti Rust] complete all as specified and as directed. Note: Horizontal barbed wire & angle iron supports shall be measured and paid separately under relevant items of Schedule "A". Measurement shall be made for stretched length.

S & F Galvanised, 2 Strand, Steel Barbed Wire 2.24mm dia, Barbed with 2mm dia bars at 75mm spacing and straining and fixing to any type of standard rails straining bolts including securing or tying at crossing with and provision of galvanised mild steel wire, staples or steel pins etc complete all as specified and directed. Note: Each line of wire will be measured for payment.

M & L for 12mm thick Preformed Bituminous Filler boards, cut to size required, inserted in expansion joints, packed properly complete all as specified and directed.

M & L for Roof tiles, Mini Mangalore pattern, interlocking at side joints, laid dry all as specified and as directed.

M & L for Water Proof treatment to Roof slab by brushing neat cement slurry with 3.0 KG of cement per Sq.m area, rendering 10mm thick in cement mortar 1:3 mixed with water proofing compound of approved make as per manufacturers instructions and finished even and smooth without using extra cement to receive the water proofing membrane, priming the surface with a coat of cold applied bituminous primer @ 0.50 KG per Sq.m, applying a coat of Blown Bitumen of grade 85/25 @ 1.2 Kg per Sq.m, laying Polymeric water proofing membrane of weight not less than 3.00 Kg per Sq.m reinforced with polyester non-woven fabric of weight not less than 150 Grams per Sq.m, by torch application with side over lap of 100mm & end over lap of 150mm & tucked into the chases on vertical surfaces by thermo fusionand finished with a coat of bituminous aluminium paint @ 100 grams per Sq.m on top complete all as specified and as directed. Note: Water proofing compound will be measured and paid separately.

M & L for 100 mm thick, PCC 1:4:8, Type D-2, using 40 mm graded stone aggregate as in Sub base for flooring/ hardstanding finished even and fair complete all as specified and as directed.

M & L for 75 mm thick, PCC 1:4:8, Type D-2, using 40 mm graded stone aggregate as in Sub base for flooring/ hardstanding finished even and fair complete all as specified and as directed.

M & L for 25 mm average thick PCC 1:2:4, Type B-0, using 12.5mm graded aggregate as in levelling course over sub base, surface finished even and fair to receive topping layer complete all as specified and as directed.

M & L for 100 mm thick PCC 1:2:4, Type B-2, using 40mm graded aggregate as in Flooring/ hardstanding, surface finished even and smooth without using extra cement complete all as specified and as directed.

M & L for 40 mm thick PCC 1:2:4, Type B-1, using 20mm graded aggregate as in Flooring/ hardstanding, surface finished even and smooth without using extra cement complete all as specified and as directed.

M & L for Glass dividing strips, 38mm wide, 3mm thick, inserted in position, conform to design all as specified and as directed.

M & L for Non Skid Ceramic Tiles, Edge cut, Coloured, of size exceeding 0.11 Sq.m and not exceeding 0.18 Sq.m, 8 mm thick [Square or Rectangular] as in Vertical Surfaces such as Skirting, Dado etc. set and jointed in neat cement slurry and pointed flush using polymer based cementitious tiling joint filler to match the shade of the tile over backing coat of 10mm thick in Cement Mortar 1:3 complete all as specified and as directed. Note: The colour / shade / design of tiles shall be as approved by GE.

M & L for Joint Free Glazed Ceramic Tiles, Edge Cut, Concept Type, Coloured, Premium Quality, of size 450 mm X 300 mm or 350 mm X 250 mm, 7 to 8 mm thick as in Vertical Surfaces such as Skirting, Dado etc. set and jointed in neat cement slurry and pointed flush using polymer based cementitious tiling joint filler to match the shade of the tile over backing coat of 10mm thick in Cement Mortar 1:3 complete all as specified and as directed. Note: The colour / shade / design of tiles shall be as approved by GE.

M & L for Non Skid Ceramic Tiles, Joint Free, Coloured, of size exceeding 0.11 Sq.m and not exceeding 0.18 Sq.m, 8 mm thick [Square or Rectangular] as in Floors, skirtings, etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed or bedding layer of mortar 15 mm thick in Cement Mortar 1:4 complete all as specified and as directed.

M & L for Granite Stone Slabs of 18 to 20 mm thick of Colour Mexican Red / Ruby Red / Z Black / Pearl Black as in Floors, Treads of Steps, Window Cills, Cooking Platform etc., and the like with machine cut edges, Table rubbed and prepolished to smooth mirror finish all to required sizes, granite stone slabs shall be of design / pattern as directed, including inlays, borders, margins in two or more colours / shades, designs / patterns of stone slabs, set and bedded with grey cement [slurry] and jointed and pointed flush using polymer based cementitious tiling joint filler to match the shade of the Granite Slabs including screed bed or bedding layer of mortar 20 mm thick in Cement Mortar 1:4 complete all as specified and as directed. Note: Single stone slab shall be used for entire Width and Length of Steps, Window Cills, Cooking Platform etc. and joints shall match with the flooring. The edges of treads shall be bull nosed / half rounded. The edges of the treads and landings shall also be provided with three Nos of grooves.

M & L for Granite Stone Slabs of 18 to 20 mm thick of Colour Mexican Red / Ruby Red/ Z Black / Pearl Black as in Skirting, Dado, Risers of Steps, Jambs, Pillars, Wall Lining [Veneering to Wall] etc. with machine cut edges, Table rubbed and prepolished to smooth mirror finish all to required sizes, granite stone slabs shall be of design / pattern as directed, including diagonals, inlays, borders, margins in two or more colours / shades, designs / patterns of stone slabs, set and bedded with grey cement [slurry] and jointed and pointed flush using polymer based cementitious tiling joint filler to match the shade of the Granite Slabs over backing coat of 10mm thick in Cement Mortar 1:3 complete all as specified and as directed. Notes: [a] Single stone slab shall be used for entire height of Skirting / Dado / Risers and joints shall match with the flooring. [b] The qoted rate shall be deemed to include for provision of SS clamps (Grade 202) of size 150mm x 30mm X 2mm made to shape required and drilled and fixed into walls/ columns, etc. at suitable intervals including cutting 'V' groove at top and bottom of each slab to insert the clamps into the slab.

M & L for machine cut Kota stone slab as in flooring, platform, landing of staircase using 20 to 25mm thick slabs, laid and jointed with grey cement slurry mixed with a admixture of pigment to match shade of slab including rubbing and polishing to smooth mirror finish all to required sizes, the size and design / pattern of slabs shall be as directed, including diagonals, inlays, borders, margins in two or more shades of slabs including screed bed or bedding layer of mortar 15 mm thick in Cement Mortar 1:4 complete all as specified and as directed.

M & L for machine cut Kota stone slab as in riser of steps, skirting, dado etc. using 20 to 25mm thick slabs laid and jointed with grey cement slurry mixed with a admixture of pigment to match shade of slab including rubbing and polishing to smooth mirror finish all to required sizes, the size and design / pattern of slabs shall be as directed, including borders, margins in two or more shades of slabs over backing coat of 10mm thick in cement mortar 1:3 complete all as specified and as directed.

M & L for 75mm thick, PCC 1:3:6, Type C-1, using 20mm graded aggregate as in Plinth protection etc surface finished even and smooth with out using extra cement and providing 12mm thick joints for full depth of PCC at every 3.00 m and every change of direction duly filled with mastic filling comprising of 01 Part of heated bitumen blown grade of any penetration and 3 parts of sand [all by weight] complete all as specified and as directed.

M & L for Inter Locking Paving Blocks of 60mm thick, made with M-35 Grade cement concrete using 20 mm graded stone aggregate, Hydraulically pressed of approved colour and pattern pre-polished with glossy finish conforming to IS - 15658 set in floors complete all as specified and directed.

M & L for rendering 5 mm thick in Cement Mortar 1:3 on ceiling surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M & L for rendering to brick / concrete surfaces, 10 mm thick in Cement Mortar 1:6, surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M & L for rendering to brick / concrete surfaces, 15 mm thick in Cement Mortar 1:4 and finishing the top surface even and smooth without using extra cement complete all as specified and as directed.

M & L for rendering 5mm thick in cement mortar 1:4 including mixing water proofing compound as per manufacturers instructions over a backing coat of 10mm thick in CM 1:6 on concrete or brick masonry surfaces and finishing the top surface even and smooth without using extra cement complete all as specified and as directed. Note: Water proofing compound will be measured and paid separately.

M & L for preparing newly plastered ceiling surfaces and applying three coats of white washing complete all as specified and as directed.

M & L for preparing newly plastered wall surfaces and applying three coats of white washing complete all as specified and as directed.

M & L for preparing newly plastered wall surfaces by using vaccume based sanding machine and applying two coats of Acrylic washable Distemper by using auto roller/airless sprayer, over a coat of alkali resistant primer over 1mm thick Cement based Wall Care Putty on walls by using multipurpose mixture for proper mixing of putty and putty sprayer for application of putty including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces complete all as specified and as directed. Note:- The contractor shall carryout Distempering & allied works under subject work through the Authorised Applicator of the manufacturer only. The lowest bidder shall submit MoU from manufacturer to provide technical support and trained persons for carrying out Distempering & allied works through their authorised applicators before commencement of the work to GE for approval.

M & L for Two coats of Weather Proof Exterior Emulsion Paint [100% Acrylic] by using auto roller/ airless sprayer over a Coat of Exterior Primer [primer shall be of same manufacturer as that of exterior emulsion paint] on newly plastered walls, pillasters, bands, borders, soffits of chajjas and projections including rubbing with sand paper to obtain a smooth surface complete all as specified and as directed. Note:- The contractor shall carryout Exterior Emulsion Painting and allied works under subject work through the Authorised Applicator of the manufacturer only. The lowest bidder shall submit MoU from manufacturer to provide technical support and trained persons for carrying out Exterior Emulsion Painting through their authorised applicators before commencement of the work to GE for approval.

M & L for two coats of synthetic enamel paint over one coat of pink primer to newly untreated wooden surfaces over 10cm width or girth including preparation of surfaces complete all as specified and as directed.

M & L for two coats of Synthetic Enamel paint over one coat of Red Oxide / Zinc Chrome Primer on new steel surfaces over 10cm width or girth including preparation of surfaces complete all as specified and as directed.

S & F Rotational Moulded Polythene [HDPE] Water Tanks, Double Layered, ISI Marked, Cylindrical & Vertical Type 1000 Litres Capacity hoisted and fixed in position including provision of suitable spouts for connecting inlet, outlet, over flow and washout pipes complete all as specified and as directed.

S & F Rotational Moulded Polythene [HDPE] Water Tanks, Double Layered, ISI Marked, Cylindrical & Vertical Type 500 Litres Capacity hoisted and fixed in position including provision of suitable spouts for connecting inlet, outlet, over flow and washout pipes complete all as specified and as directed.

S & F Ball Valves, 20 mm Bore, high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe etc complete all as specified and as directed.

S & F Gun Metal Globe or Gate Valve of Class - I, Pressure Tested of 1.5 MPa, 40mm bore with iron wheel head, screwed both ends for iron pipe, conforming to IS, ISI Marked complete all specified and as directed.

S & F Gun Metal Globe or Gate Valve of Class - I, Pressure Tested of 1.5 MPa, 25mm bore with iron wheel head, screwed both ends for iron pipe, conforming to IS, ISI Marked complete all specified and as directed.

S & F Gun Metal Globe or Gate Valve of Class - I, Pressure Tested of 1.5 MPa, 20mm bore with iron wheel head, screwed both ends for iron pipe, conforming to IS, ISI Marked complete all specified and as directed.

S & F GI pipes of 15 mm bore, medium grade conforming to IS - 1239 [Part - 1] as in water tubing including all fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc fixed to walls, ceiling or laid on floors including testing complete all as specified and as directed.

S & F GI pipes of 25 mm bore, medium grade conforming to IS - 1239 [Part - 1] as in water tubing including all fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc fixed to walls, ceiling or laid in floors/ trenches including testing complete all as specified and as directed.

S & F GI pipes of 40 mm bore, medium grade conforming to IS - 1239 [Part - 1] as in water tubing including all fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc laid in floors/ trenches including testing complete all as specified and as directed.

Cutting existing steel tubing for alterations or additions [each cut measured] for 50mm bore pipe complete all as specified and as directed.

Taking down existing GI water tubings of any description upto 100 mm bore size and re-routing the same with all necessary accessories and fittings as required complete all as specified and as directed. Note: Excavation & earthwork shall be measured and paid separately under relevant items of this BoQ.

S & F 20 mm outer diameter CPVC Pipes SDR 11 & Plain CPVC SDR 11 Fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc., concealed in walls/ ceiling including testing complete all as specified and as directed. Note: The rate quoted shall be deemed to include the cost of cutting chases of suitable size and making good.

S & F Bib Taps, 15 mm dia, Brass Chromium Plated, Fancy Type with crutch or butterfly handle, screwed down for iron pipe and fixed etc. complete all as specified and as directed.

S & F Two way Bib Cock, 15 mm dia, Brass Chromium Plated, with crutch or butterfly handle, screwed down for iron pipe and fixed etc. complete all as specified.

S & F Health Faucet, ABS body, including 1.00 m long flexible tube, ABS wall hook, non return valve complete all as specified.

S & F Stop Valves/ Angle Valves, 15 mm bore dia of pipe, Brass, Chromium Plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions etc complete all as specified and as directed.

S & F Stop Valves/ Angle Valves, 15 mm dia, cast copper alloy with capstan head, Chromium Plated, Fancy Type, screwed down high pressure with long shank and cup [concealed type] for iron pipe etc complete all as specified and as directed.

S & F Pillar Taps, Brass Chromium Plated, 15 mm dia, with capstan head, screwed down high pressure with or with out lettered "Hot" or "Cold" with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as specified.

S & F Corner Glass Shelf of radius 250mm with 5mm thick touhgened glass and SS railing/ cage and Chromium plated Brackets complete all as specified and as directed.

S & F Soap Dish, Stainless Steel, Fancy Type, size 160mm x 160mm complete all as specified.

S & F Brass Chromium Plated Tubular Towel Rail, 20mm dia, D Type, 600 mm long between flanges complete all as specified and as directed.

S & F PTMT Tubular Towel Rail, 20mm dia, 450 mm long between flanges, minimum weight 170 Grams, complete all as specified and as directed.

S & F Brass Chromium Plated Shower Rose of size 125mm with or with out swivel joints fixing to steel pipes complete all as specified and as directed.

S & F in repairs Vitreous China Ware Wash Hand Basin, White, Flat Back of size 550 mm X 400 mm including brass chromium plated waste fittings with long screw shanks and fly nuts, flange end bedded in red led cement and other end fixed, rubber plug with rings including CI Brackets, cutting for and pinning in ends of brackets or erecting strand, 32mm bore PVC flexible waste pipe, PVC Connection of PTMT complete all as specified and as directed.

S & F in repairs Vitreous China Ware Wash Hand Basin, White, Flat Back of size 450 mm X 300 mm including brass chromium plated waste fittings with long screw shanks and fly nuts, flange end bedded in red led cement and other end fixed, rubber plug with rings including CI Brackets, cutting for and pinning in ends of brackets or erecting strand, 32mm bore PVC flexible waste pipe, PVC Connection of PTMT 600mm long complete all as specified and as directed.

S & F Vitreous China Wash Down Water Closet [Pedestal pattern], White, including 10 Litres capacity, PVC Valve less, Syphonic action type, low level flushing cistern, white, with inlet ball valve, float, handle, flush pipe of polyethylene of low or high density of PVC, 32mm dia, PVC Connection of 15mm Bore and 600mm long with PTMT check nut and union etc. including brackets and connections to pipe and flush pipe including plastic water closet seat back closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device and 'P' or 'S' trap complete all as specified and as directed.

M & L for 50mm bore dia High Density Polyethylene Pipes [HDPE of pressure rating 6 KGf / Sq.cm laid in trenches or fixed to walls or ceilings or in floors etc. complete all as specified

S & F 75mm bore PVC [SWR] pipes single socketed, in any length with rubber ring/ solvent cement joints, laid in trenches or in floors complete all as specified and as directed.

S & F 110mm bore PVC [SWR] pipes single socketed, in any length with rubber ring/ solvent cement joints, laid in trenches or in floors complete all as specified and as directed.

S & F 75mm bore PVC [SWR] pipes single socketed, in any length with rubber ring/ solvent cement joints, fixed to walls in any position with necessary brackets, clamps, bolts, nuts, etc., complete all as specified and as directed.

S & F 110mm bore PVC [SWR] pipes single socketed, in any length with rubber ring/ solvent cement joints, fixed to walls in any position with necessary brackets, clamps, bolts, nuts, etc., complete all as specified and as directed.

S & F 75 mm bore PVC [SWR] bends, any radius including jointing with solvent cement complete all as specified and as directed.

S & F 110 mm bore PVC [SWR] bends, any radius including jointing with solvent cement complete all as specified and as directed.

S & F 110 mm bore PVC [SWR] Junction Single [Single "T"] equal or unequal with access door including jointing with solvent cement complete all as specified and as directed.

S & F 75 mm bore PVC [SWR] Vent Cowl including jointing with solvent cement complete all as specified and as directed.

S & F 110 mm bore PVC [SWR] Vent Cowl including jointing with solvent cement complete all as specified and as directed.

S & F PVC [SWR] Floor Trap, 75mm dia outlet, plain with grating including jointing with solvent cement complete all as specified and as directed.

S & F Grating doom 100mm dia of PTMT (Minimum weight 25gms) includingsetting with solvent cement complete all as specified and as directed.

M & L for 150 mm dia RCC Pipes, Class NP3, laid and jointed with collars laid in trenches and jointed complete all as specified and as directed.

M & L for concrete bed to drain pipes of size 150 mm bore packing under and haunching against the sides of pipes after they are laid and fitted in cement concrete, Type C2, 1:3:6, using 40mm graded stone aggregate complete all as specified and as directed.

M & L for Conventional type LLDPE Septic Tank of 10 Users Capacity designed to carry Sewage and Sullage Water including excavation in any type of Soil, PCC 1:4:8, type D2 below Foundation, Vent Shaft connection etc. complete all as specified and as directed.

M & L for Soakage Well of size 1.20m dia and 1.50m effective depth including excavation in any type of soil, Foundation in PCC 1:3:6, type C2 with Honeycombed Masonry Walls with top ring in M30 Grade Design Mix Concrete including Intercepting Chamber and Screen Chamber made of Brick Masonry in Cement Mortar 1:6, RCC Cover Slab in M30 Grade Design Mix Concrete / SFRC Cover interconnecting pipes of RCC/DWC complete filled with brick bats with all ancillaries, fittings, fixtures complete all as specified and as shown on drawings and as directed.

M & L for 100 mm thick [compacted thickness] Water Bound Macadam with coarse aggregate of Grading 2 [63 to 40mm size] spread, rolled with power road roller of 8 to 12 ton capacity and consolidated to gradient and camber required complete all as specified and as directed.

M & L for Preparing surfaces of unsurfaced Water Bound Macadam surfaces by brushing with wire brushes for removing caked mud etc, sweeping with brooms and finally fanning the cleaned surfaces with gunny bags to remove all loose dirt etc and applying evenly a Priming/Tack coat with bituminous primer at 10 kg per 10 Sq.m using paving bitumen Grade VG-30 complete all as specified and as directed.

M & L for Premixed Bituminous Macadam laid / rolled and compacted to required gradient and camber [consolidate thickness 75mm or less] using paving bitumen of Grade VG - 30 as binder with 4% by weight of total mix using Hot Mix Plant and Mechanical Paver, rolled and compacted with power road roller of 8 to 12 ton capacity to required camber and gradient complete all as specified and as directed.

M & L for Preparing existing black top surfaces by brushing with wire brushes for removing caked mud etc. sweeping with brooms and finally fanning the cleaned surfaces with gunny bags to remove all dirt etc. and applying evenly a priming / tack coat with bituminous primer at 5 KG per 10 Sq.m using paving bitumen Grade VG-30 complete all as specified and as directed.

M & L for laying Bituminous Premixed Semi Dense Asphaltic Concrete, 40 mm consolidated thickness, using paving bitumen of Grade VG – 30, with 5.5% of binder content by weight of total mix using Hot Mix Plant and Mechanical Paver, rolled and compacted with power road roller of 8 to 12 ton capacity to required camber and gradient complete all as specified. Note: Minimum Bitumen content shall be 5.5% as specified here in above. Please note that if the actual quantity of bitumen to be incorporated on approval of Mix–Design is found more than the minimum bitumen content specified above, No price adjustment shall be made for actual bitumen content of Mix–Design. Bitumen shall be Paving Bitumen of Grade VG–30 and shall be procured by the contractor.

M & L for Road Marking Strips, Lines, Dashes, Arrows, Letters etc of 2.5 mm thick [Reflective Type] of colour White or Golden Yellow on roads, pavements and the like exceeding 10cm wide with Hot Thermo Plast material by fully automatic thermoplastic paint applicator machine, fitted with profile shoe, glass beads dispenser, propane tank heaters and profile shoe heater, driven by skilled operator on road surface complete as per MOSRT & H specifications including cleaning the road surface of all dirt, scales, oil grease and foreign materials etc complete all as specified and as directed.

S & F in repairs Solar Road Studs [Bi-Directional] as per approved model and conforming to IRC - 67, made of pressure Die cast Aluminium alloy of size 125 X 125 [Approximately], with built-in stem of suitable length for fixing with epoxy, working on High Efficiency Mono-Crystalline Solar Panel 2.4 V / 0.3 Watt, One Ni-Mh or NI-cd Rechargeable Battery [1.2V / 1600 MA] with 06 Super Bright LEDs with 10,000 to 18,000 mcd [Millicandela], with a minimum Operating time of 3-4 consecutive days with full charge in 8-10 hrs, viewing distance / visibility not less than 800m with 2 Hz Flash Rate, Self operated from Dusk to Dawn, with high intensity reflective grade polymer sticker and conforming to IS - 12063, of Colour yellow or red or blue or green or white as approved by GE complete all as specified and as directed. Make : Cat Part No. GPL-03-01 of Make: GREENLITE or equivalent model in makes 3M/ Dark Eye/ Ace/ Trafitronics/ Lion/ Automat

S & F Retro Reflective Sign Boards [Both Sides Written] made up of 2mm thick aluminium sheet, face to be fully covered with high Intensity Prismatic [Type-IV] sheeting conforming to Type III of ASTDM-D 4956-01 as approved by GE with letters [Black, Roman, Italic or Indian] including necessary stops, commas, short lines, dashes, brackets, etc., [Number of alphabets not exceeding 30 Nos per each side], index hands [Natural size] or arrows [upto 400mm long] one number, borders, etc. as per IRC 67 - 2001 in silver/white with blue/green or any other colour back ground and with high intensity grade, pasted on substrate by pressure sensitive adhesive backing which shall be activated by applying pressure conforming to Class II ASTDM - D - 1956 -01 and fixing same to the structural frame work by means of suitable size aluminium alloy, rivets or bolts and nuts including the cost of painting with two coats of epoxy paint in grey colour on the back side of aluminium sheet and erecting in position complete all as specified and as directed. Note: Rate quoted is deemed to be including PCC 1:2:4, Type B1 block of size 450 X 450 X 600mm for fixing MS Post, 2 Nos of MS Posts made out of 50mm Bore, Medium Grade, MS Pipe of 3.00m long, Structural frame work with 25mm Square Pipe with 1.6mm thick wall, applying two coats of synthetic enamel paint over a coat of Zinc Chrome primer to MS framed work and earthwork etc.

S & F Speed-Breaker as per approved model and conforming to IRC - 67, having Dual-directional high intensity cube corner reflector ultrasonic welded to high impact resistant plastic body of colour yellow and black of size 250x345x50mm (height) with shape of side body to have interlocking pattern to keep all speed breakers in a row fixed with reuired numbers of steel nails all as specified and as directed. Make : Cat Part No. GPL-07-06 of Make: GREENLITE or equivalent model in makes 3M/ Dark Eye/ Sinor Infrasttructure.

M & L for Point Wiring complete with 1100 Volts, FRLS Grade, 1.5 Sq.mm, Single Core, Two runs, PVC Insulated, Unsheathed, Multistranded Copper Conductor Cable, conforming to IS - 694 drawn through and including heavy duty PVC Conduit, 20 mm dia including all accessories concealed in Walls / Roofs / Floors / Ceiling etc. or surface type / semi concealed type and Metal GI Flush Box of suitable size and thickness including Modular type Base / Grid Frame & Cover Frame for housing Modular Type Switches, Sockets and Regulators etc. concealed in walls, including 1100 Volts, FRLS Grade, 1.5 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor cable as earth continuity conductor with colour coding and connecting to Earth Dolly for One Light / Fan Point / Bell Point complete all as specified and as directed.

All as per Serial Item No. 170 above but one 3 Pin Socket Outlet 6 Amps on independent board, complete all as specified.

All as per Serial Item No. 170 above but one 3 Pin Socket Outlet 16 Amps power point on independent board, with 1100 Volts, FRLS grade, 4 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor Cable confirming to IS - 694 and including 1100 Volts, FRLS grade, 4 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor Cable as Earth Continuity Conductor.

S & F Switch, Modular Type, One Module, Single Pole, One Way, 6 Amps, 230 Volts complete all as specified and as directed.

S & F Switch Modular type, one module, Single pole, one way, 16 Amps, 230 Volts complete all as specified and as directed.

S & F Socket Outlet, 3 Pin, 6 Amps, Modular Type, Two Modules, 230 Volts, complete all as specified and as directed.

S & F Socket Outlet, 3 pin, 16 Amps, Modular Type, Two Modules, Multipurpose, 230 Volts complete all as specified and as directed.

S & F Electronic Fan Regulator, Stepped Type, Modular Type, Two Module, 120 W, AC, 230 Volts, Single Pole complete all as specified and as directed.

S & F Ceiling Rose, PVC Body, 65 X 50 mm, Three Terminals, 230 Volts complete all as specified and as directed.

M & L for Sub main wiring with 2 runs of single core 4 Sq.mm Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor cable, 1100 Volts, FRLS Grade, ISI Marked, drawing through and including heavy duty PVC Conduit, 25 mm dia with all accessories concealed in Walls / Roofs / Floors / Ceiling etc. or surface type / semi concealed type including One run of 4 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor cable, 1100 Volts, FRLS Grade earth continuity conductor including taking down old unserviceable submain wiring and wooden battens / conduits / casing capping and making good the disturbed surfaces all as per existing complete all as specified and as directed. Note: 3 runs of 4 Sq.mm & one run of 25 mm dia PVC Conduit will be measured as one unit.

S & F MCB DB, TPN, 4 Way, 415 Volts, with DIN Channel, Double Door with 200 Amps rated bus bar suitable for mounting MCBs flush mounted with wall complete all as specified and as directed.

S & F MCB DB, SPN, 12 Way, 240 Volts, with DIN Channel, Double Door with 100 Amps rated bus bar suitable for mounting MCBs flush mounted with wall complete all as specified and as directed.

S & F MCB, TPN, 6 to 32 Amps, 10 KA, C Curve, AC, 230 Volts, 50 Hz complete all as specified and as directed.

S & F MCB, TPN, 63 Amps, 10 KA, C Curve, AC, 230 Volts, 50 Hz complete all as specified and as directed.

S & F MCB, SPN, 6 to 32 Amps, 10 KA, C Curve, AC, 230 Volts, 50 Hz complete all as specified and as directed.

S & F MCB, SP, 6 to 32 Amps, 10 KA, C Curve, AC, 240 Volts, 50 Hz complete all as specified and as directed.

S & F Surface & wall mounted Energy efficient LED Tube Light Fitting, of not less than 900 Lumens output, 5700 K of cool white, with extruded aluminium / CRCA housing and robust construction with necessary acrylic diffuser & integrated electronic driver, all accessories internally prewired and connecting up with twin core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm complete all as specified and as directed. Note: Light fitting shall be of PF>0.95

S & F Surface & wall mounted Energy efficient LED Tube Light Fitting, of not less than 1800 Lumens output, 5700 K of cool white, with extruded aluminium / CRCA housing and robust construction with necessary acrylic diffuser & integrated electronic driver, all accessories internally prewired and connecting up with twin core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm complete all as specified and as directed. Note: Light fitting shall be of PF>0.95

S & F Energy efficient & Long life Security Light Luminaire, 35 Watt with Pressure die-cast Aluminium housing, IP 65 Protection, heat resistant glass cover, high power LEDs as light source, electronic driver including GI Bracket made out of 32 mm bore GI Tube, Medium Grade of size not exceeding 2.00 m in length and bent to shape required and fixed with 2 Nos of Pole fitting Clamps made out of MS Flat of size 50 X 6mm, bolts, nuts, washers and painting with two coats of aluminium paint over a coat of primer red oxide zinc chrome primer and connecting up with three core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm complete all as specified and as directed. Note: Light fitting shall be of PF>0.95

S & F surface mounted LED Downlight of not less than 1500 Lumens output, with Aluminium Heat Sink, Round/ Square shap, PC diffuser in white powder coated finish with independent electronic LED driver all accessories internally prewired and connecting up with three core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm including taking down existing light fittings of any description and making good the disturbed surfaces to match with existing complete all as specified and as directed. Note: Light fitting shall be of PF>0.95

S & F Energy efficient Post Top Lantern, of not less than 4000 Lumens output, 5700 K, with Pressure Die Cast Aluminium Housing,with Opal Acrylic Diffuser, IP65 Protection, electronic driver, all accessories internally prewired and connecting up with three core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm including taking down existing light fittings of any description and making good the disturbed surfaces to match with existing complete all as specified and as directed. Note: Light fitting shall be of PF>0.95

S & F Energy efficient LED Flood Light fitting, of not less than 8000 Lumens output, 6500 K, with Pressure Die Cast Aluminium Housing, IP 66 Protection and Surge Protection device of 10 KV, Heat resistant Toughened Glass Cover, high power LEDs as light source, electronic driver and connecting up with three core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm complete all as specified and as directed. Note: Light fitting shall be of PF>0.95

S & F Factory made Pole Mounted Polycarbonate Junction Box [Loop-In / Loop-Out Box] of size 205 X 255 X 112mm with IP 69 Protection and locking screws, Neutral Link Mounted and DIN Rail of suitable size for mounting MCB / Connector etc. complete in the box and including MCB, SP, 6 Amps, B Curve, 240 Volts [1 Nos], 50 Amps rated Heavy Duty, TP Connector [1 Nos] and for incomer and outgoing cable, suitable for Pole mounting and fixed with Stainless Steel Clamps with suitable SS Nuts, Bolts, Glands, Lugs etc. complete all as specified and as directed.

S & F Energy efficient, Low Noise, Ceiling Fan, 1200mm Sweep of any colour as approved, 03 blades, BEE 5 Star Rated, with BLDC Motor, Copper Wound, 350 RPM, with Double Ball Bearing, Conforming to IS - 374, ISI Marked, suitable for operation on Single Phase, 240 Volts, AC, 50Hz, including Down Rod, Canopies, Shackles, Safety Rope, Hanging Clamps, Bushes, having P.F >0.95, Service Value >6.5, Air Delivery >215 CMM, Power Consumption less than 35 Watt, THD less than 5% including provision of Electronic speed control Regulator step type, including connecting up with three core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm complete all as specified and as directed. Note: Ceiling Fan shall be provided with 03 Years onsite replacement warranty. Rate quoted is deemed to be including the same and nothing shall be paid extra on this account.

S & F Exhaust Fan, 300mm Sweep, 900 RPM, Metal Body, Heavy Duty, with Double Ball Bearing, Conforming to IS - 2312, ISI Marked, suitable for operation on Single Phase, 240 Volts, AC, 50 Hz, including Louvers Shutter / Grill, BEE 5 Star Rated and of approved colour including connecting up with twin core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm complete all as specified and as directed.

Supplying, laying and testing XLPE insulated, armoured heavy duty underground cable, ISI marked with aluminium stranded conductor 1100 Volt grade of size 4 Core, 16 Sq.mm cross section suitable for earthed system, laying in trenches/duct/fixed to poles/drawn through pipes/sleeving through pipe in duct, including suitable size Double compression copper stainless steel cable gland, crimping type cable lugs, sockets etc. complete all as specified and as directed.

Supplying, laying and testing XLPE insulated, armoured heavy duty underground cable, ISI marked with aluminium stranded conductor 1100 Volt grade of size 4 Core, 10 Sq.mm cross section suitable for earthed system, laying in trenches/duct/fixed to poles/drawn through pipes/sleeving through pipe in duct, including suitable size Double compression copper stainless steel cable gland, crimping type cable lugs, sockets etc. complete all as specified and as directed.

M & L for Dry River Sand cushioning over and around the cable for cable protection in trenches, levelled and punned down complete all as specified and as directed. Note: The punned down thickness shall be measured for payment.

Supplying and laying un–reinforced precast concrete cable cover, Class LV, Type 1, Flat, of size 250mm x 150mm x 40mm complete all as specified and as directed.

M & L for Bricks, common burnt clay building bricks, sub–class "B", designation 75 in trenches for cable protection complete all as specified and as directed.

S & F GI tubes of 40 mm bore, light grade conforming to IS – 1239 [Part – 1] including all fittings, fixed to walls, ceiling or laid in floors/ trenches as in cable protection complete all as specified and as directed.

M & L for Cutting Bituminous Road / Hardstanding etc. as required for Jointing / Laying Cables and Pipeline of width not exceeding 300mm and depth not exceeding 600mm and refilling with approved earth after laying and making good the top surface with 100mm thick PCC 1:2:4, Type B1 using 20mm graded stone aggregate, complete all as specified and as directed.

Taking down existing LT UG cable of any description upto 120 sq.cm. size and re-routing the same with all necessary accessories and joints as required complete all as specified and as directed. Note: Excavation & earthwork, sand cushioning, cable protection shall be measured and paid separately under relevant items of this BoQ.

Earthing complete with Galvanised Steel Earth Plate Electrode 600 X 600 X 6 mm thick burried directly in ground [earth pit not less than 2.25 m deep below ground level] with top edge of Plate not less than 1.50 m below normal ground level connected to 4 mm GI Wire [Earth Lead] and GI pipe 15 mm, Medium Grade for earthing lead protection to the extent of maximum 7.5m, Earth Plate Electrode surrounded by 150mm thick packed layers of Charcoal and Common Salt filled in alternate layers, connected to the Plate by means of GI Bolts & Nuts complete all as per Electrical Plate No. 3 of SSR Part – I, connected to panel / DB including testing on completion including main earthing, Charcoal, Common Salt, PCC [1:2:4, Type B1] Pit with RCC 1:2:4, Type B1 Cover, 50 mm thick with 6 Nos, 8 mm dia TMT bars in both ways, MS frame made with 40 X 40 X 6 mm Angle Iron, MS Funnel with 20 mm bore, medium grade GI Watering pipe, wire mesh, earth work excavation, return filling, removal of surplus soil etc. complete all as specified and as directed.

S & F Earth continuity Conductor or main earthing lead made of GI Wire of 4 Sqmm including GI pipe 15 mm, Medium Grade for earthing lead protection fixed to wall on batten or recess or chases or burried in ground or fixed to poles or any other indicated situation including drawing through GI Pipe for earthing etc. complete all as specified and as directed.

V R K CONSTRUCTIONS

SREE VIGNESWARA CONSTRUCTIONS

M B CONSTRUCTIONS

SRI VENKATA SAI MANIKANTA CONSTRUCTIONS