Civil Work

Name Of Work :- Construction of New Anganvadi at Various Village of Chokari - 5 and Majatan - 2 Ta.Padra , Dist. Vadodara

Taluka :Vadodara District : Vadodara

Bill of Quantities

Item of work Quantities Rate in Amount

Estimated Unit Figures in

1 Excavation for foundation upto 1.5 m depth including sorting out and stacking of 90.08 Cum 208.93

useful materials and disposing off the excavated stuff upto 50 Meter lead. for

Loose or soft soil

2 Excavation for foundation for depth from 1.5 m to 3.0 m including sorting out 54.54 Cum 289.92

and stacking of useful materials and disposing off the excavated stuff upto

Meter lead for Dense or Hard soil

3 Providing and laying cement concrete 1:3:6 (1-Cement : 3- coarse sand : 6- hand 10.08 Cum 3080.90

broken stone aggregates 40 mmnominal size) and curing complete excluding cost

of formwork in Foundation and Plinth

4 Providing and laying controlled cement concrete M.200 and curing complete 10.36 Cum 4529.85

including the cost of formwork and reinforcement for reinforced concrete work

in Foundations, footings, Base of columns and Mass concrete.

5 Providing and laying controlled cement concrete M.200 and curing complete 16.16 Cum 7997.18

including the cost of formwork and excluding cost of reinforcement for

reinforced concrete work in Columns, Pillars posts and struts, For Ground Floor

6 Filling available excavated earth (excluding rock) in trenches. plinth, 72.32 Cum 133.65

sides of foundations etc. in layers not exceeding 20 cm. in depth consolidating

each disposited layer by ramming and watering.

7 Providing and laying controlled cement concrete M.200 and curing complete 7.88 Cum 6672.06

including the cost of formwork and excluding cost of reinforcement for

reinforced concrete work for Ground Beam and SOG Beam

8 Brick work using common burnt clay building bricks having crushing strength 43.60 Cum 4121.55

not less than 35 kg./Sq.Cm. in foundation and plinth in Cement Mortar 1:6 (1-

Cement : 6 -fine sand) (Conventional Brick)

9 Filling in foundation and plinth with murrum or selected soil in layers of 20cm. 37.66 Cum 296.29

thickness including watering, ramming and consolidating etc. complete.

10 Providing and laying controlled cement concrete M.150 for curing complete 6.28 Cum 4479.35

including cost of formwork and excluding cost of reinforcement for reinforced

concrete work for Plinth Slab

11 Earthwork for embankment including breaking clods, dressing with all lead and 34.46 Cum 4403.40

lift and including watering rolling and consolidation of subgrade in layers at

O.M.C. to required dry density including filling the depression which occur

during the process using power roller 8T to 10T.(C) From Borrow area within

12 (i) Half brick masonry in common brunt clay building bricks having crushing 26.72 Sqm 669.50

strength not less than 35 Kg/Sq.Cm. for GF in Cement mortar 1:4 (1- Cement : 4 -

coarse sand ) (Conventional Brick)

13 Providing and laying controlled cement concrete M.200 and curing complete 9.86 Cum 6200.39

including the cost of formwork and reinforcement for reinforced concrete work

14 Providing and laying ordinary cement concrete 1:2:4 (1- Cement 2- coarse sand : 1.30 Cum 10219.39

4- graded stone aggregates 20 mm nominal size) for R.C.C lintel including

finishing smooth with,curing etc. complete including the cost of formwork but

excluding the cost of reinforcement for Ground Floor

15 Providing and laying cement concrete 1:2:4 (1- Cement : 2- Coarse sand : 4- 1.94 Cum 6544.13

graded stone aggregates 20 mm nominal size) for reinforced concrete Chhajjas

not exceeding 10cm. thickness upto floor two level including finishing the

exposed surfaces with cement mortar 1:3 (1-cement, 3 Fine sand) to give a

smooth and even surface centering and formwork and curing complete excluding

cost of reinforcement for Ground Floor

16 Providing TMT Bar FE 500D reinforcement for R.C.C. work including bending, 5760.00 KG 77.29

binding and placing in position complete for Ground Floor

02. Sch B_KPY_Pkg.6 Page

Item of work Quantities Rate in Amount

Estimated Unit Figures in

17 Providing and laying controlled cement concrete M.200 and curing complete 0.64 Cum 8037.13

including the cost of formwork and excluding cost of reinforcement for

reinforced concrete work in Columns, Pillars posts and struts For Ground Floor

slab to 1st Floor slab

18 Providing and laying controlled cement concrete M.200 and curing complete 2.88 Cum 6712.01

including the cost of formwork and excluding cost of reinforcement for

reinforced concrete work for Beams of 1st Floor

19 Brick work using common burnt clay building bricks having crushing strength 5.08 Cum 4444.90

not less than 35 kg./Sq.Cm. in Mortar 1:6 (1- Cement : 6 -fine sand)

(Conventional Brick) for 1st Floor

20 Providing and laying controlled cement concrete M.200 and curing complete 6.14 Cum 6240.34

including the cost of formwork and reinforcement for reinforced concrete work

in Slab for 1st Floor

21 Providing TMT Bar FE 500D reinforcement for R.C.C. work including bending, 951.40 KG 77.29

binding and placing in position complete For 1st Floor

22 20mm thick sand faced cement plaster on walls upto height 10 metres above 520.50 Sqm 337.52

ground level consisting of 12mm thick backing coat of C.M. 1:3 (1-cement : 3-

sand) and 8mm thick finishing coat of C.M. 1:1 (1-cement : 1-sand) etc.

complete. External Plaster upto 1st floor

23 Providing 15mm thick cement plaster in single coat on Rough (Similar)side of 366.36 Sqm 173.96

single or half brick walls for interior plastering and finished even and smooth in

(ii) Cement mortar 1:4 (1-cement :4-sand) for Interior Plaster for G.F. and 1st

24 Providing 15mm thick cement plaster in single coat on Rough (Similar)side of 115.46 Sqm 204.95

single or half brick walls for plastering and finished even and smooth in (ii)

Cement mortar 1:4 (1-cement :4-sand) for Ceiling

25 Applying 2 coat of Primer Coat of approved brands on exterior surface with 520.50 Sqm 50.50

proper cleaning etc. Item to be approved by engineer incharge or consulting

26 Finishing walls with textured ( Rustic ) pattern for scribble walls on exterior 156.14 Sqm 303.00

plastered surface pattern to be approved with consulting engineer or Engineer

27 Finishing wall with weather proof exterior emulsion paint on wall surface (two 520.50 Sqm 117.40

coats) to give an required shape even shade after thoroughly brushing the surface

to remove all dirt, and remains of loose powdered materials.etc complete

28 Applying two coats of putty & two coats of primer of approved brand and 316.50 Sqm 40.59

manufacture on new wall surface to give an even shade including thoroughly

brushing the surface free from mortar dropping and other foreign matter and sand

papered smooth.

29 Wall painting (two coats) with plastic emulsion paint of approved brand and 316.50 Sqm 80.87

manufacture on undecorated wall surface to give an even shade including

throughly brushing the surface free from mortar droppings and other foreign

matter and sand papered smooth.

30 Ceiling painting (two coats) with plastic emulsion paint of approved brand and 115.48 Sqm 86.42

manufacture on undecorated wall surface to give an even shade including

throughly brushing the surface free from mortar droppings and other foreign

matter and sand papered smooth.

31 Providing and laying Machine cut free edges machine polished telephone black 59.04 Sqm 3183.52

madras Granite stone slab 18mm (Average ) thick ( Single Piece not more than

150cm) for stair steps and risers & Door/window frame as per design including

full moulded round front steps & 1cm nosing & necessary groove on trads of

steps ;laid on 20mm thick cement mortar 1:6 ( 1 cement : 6 coarse sand ) jointed

with gray cement sluury including rubbing and polsihing etc. complete.

02. Sch B_KPY_Pkg.6 Page

Item of work Quantities Rate in Amount

Estimated Unit Figures in

32 Providing and Fixing flush door both side laminated & I.T.W. beading all around 11.50 Sqm 3194.47

by using I.T.W. frame 120 mmX 80 mm shutter fabricated from 35 mm thick

solid core malemine faced three layered pre laminated flat pressed wood based

exterior grade bonded BWP/BWR synthetic resin having stamped IS 12823 grade

I type II including three coats of lacquer polishing to exposed wooden surface &

stainless steel decorative type designs fixtures/ fastening etc including I.T.W

trinagular batten patti of size 30mm X 30mm etc as per architectural detailed

drawing & as directed by engineer incharge.

33 Providing and fixing powder coated aluminium glazed casement window 19.94 Sqm 5050.00

comprising outer frame of size 100 mm × 45 mm made from minimum 1.8 mm

thick aluminium extruded sections and openable casement shutters of size 47 mm

× 75 mm made from minimum 1.5 mm thick aluminium sections, with

fixed/openable louver panels at both top and bottom fabricated from 50 mm ×

mm aluminium louver frame sections complete with approved aluminium/glass

louvers, glazing beads, EPDM gasket, wool pile, friction stays, handles, locking

arrangement, cleats, brackets, screws, anchor fasteners and all necessary

hardware fittings. The central portion shall be glazed with 5 mm thick clear glass

/ 6 mm thick toughened glass as specified, fixed with approved sealant system.

All aluminium sections shall be powder coated in approved colour with minimum

50–60 micron coating thickness including fabrication, cutting, assembly,

transportation, erection, fixing in position, sealing with silicone sealant, making

good surrounding surfaces and all incidental works complete as per approved

drawings and directions of Engineer-in-Charge

34 Providing and fixing M.S. grills/ railings of required pattern with M.S. flats at 672.32 KG 105.18

required spacings and frame alround, square or round bars with round headed

bolts and nuts or by screws

35 Painting two coats (excluding priming coat) on new steel and other metal surface 48.92 Sqm 90.00

with enamel paint, brushing, interior to give an even shade including cleaning the

surface an even shade including cleanicn the surface of all dirt, dust and other

foreign matter.

36 P & L 24" x 24" vitrified 8 mm thick tile flooring over 20 mm (average) base of 32.12 Sqm 1452.79

cement mortar 1:6 ( 1 cement: 6 coarse sand) on new surface or fixing on

existing flooring by adhesive material including dismentaling of existing flooring

and jointed with color cement slurry including finised with flush pointing &

cleaning the surface etc. complete for light shade. Item to be approved by

engineer incharge

37 Providing and laying coloured glazed tiles of the size 300 mm x 200 mm x 8 mm 40.72 Sqm 1477.25

/ 300 mm x 450 mm x 8 mm in skirting, risers of steps and dedo on 10 mm. thick

cement plaster 1:3 (1 cement : 3 coarse sand) & jointed with white cement slurry.

38 P & L 24" x 24" vitrified 8 mm thick tile flooring over 20 mm (average) base of 3.52 Sqm 1432.78

cement mortar 1:6 ( 1 cement: 6 coarse sand) on new surface or fixing on

existing flooring by adhesive material including dismentaling of existing flooring

and jointed with color cement slurry including finised with flush pointing &

cleaning the surface etc. complete for antiskit

39 Providing and laying approved make Simpolo full body vitrified tiles for 42.54 Sqm 2020.00

decorative flooring of required size, shade, colour, texture and pattern, having

uniform colour and composition throughout the tile body, with water absorption

less than 0.5%, laid over prepared cement mortar bed / tile adhesive as specified,

including cutting, grinding, edge finishing, alignment to pattern, filling joints

with matching epoxy/cementitious grout, curing, cleaning and finishing complete.

The work shall include all materials, labour, wastage, handling, surface

preparation, tools and accessories complete as per manufacturer’s specifications,

approved samples and directions of Engineer-in-Charge.

02. Sch B_KPY_Pkg.6 Page

Item of work Quantities Rate in Amount

Estimated Unit Figures in

40 Anti-Termite System:Providing and laying of permanent piping technology anti- 106.72 Sqm 134.33

termite treatment before flooring work by installing LLDP (Low linear density

polyethylene) tube of 8 mm O.D. & 6.4 mm 1.D. with inbuilt pressure

compensation chip every 30 cm interval in the tube, having working pressure of

Kg/cm2 and release rate of 1.9 Itr/hour fixed by P-clips and nails. The LLDP

pipe shall be installed at the entire periphery of the building and at internal

network of building at a depth of 20 to 200 mm under floor at every 2 to 3 mtr.

c/c distance (adjusted as per building layout ) & Ends of loop pass through a

PVC elbow of minimum 32 mm ID at junction box of wall and floor level,

entering into a steel reinforced grooved flexible pipe of minimum 22 mm ID

leading into junction box and the loops shall terminate in junction boxes & test

every junction during injecting chemicals for termite control treatment. The anti

termite chemical Imidacloprid 30.5% SC mix as per IS-6313 (part III) shall be

injected by the pressure pump diluted with water @ 10.5 ml/5 ltr of water at the

rate of 2 Kg/sq.cm @ 5 Ltr/SMT. The contractor shall submit approved line plan

for piping system and junction boxes dully approved by Engineer-in-Charge with

bond of 5 year warranty.(i)Anti Termite chemical injected area (Chemical

injecting incl. labour cost)

41 Providing and fixing wsh down water closet wall hung matte finish outside and 2.00 Each 3535.00

glossy inside (Indian type, W.C. Pan) make cera/hindware/Kohler/Jaquar etc or

similar with integral P or S trap including jointing the trap with soil pipe in

Cement Mortar 1:1 (1-Cement : 1-fine sand) with Seal and cover of size

510X365X380 mm. Item to be approved by engineer incharge or consulting

42 Providing and fixing 40mm Dual flush cock/valve make 2.00 Each 3535.00

cera/hindware/Kohler/Jaquar etc or similar with Square plate made up of ss

to control cock operation of approved quality including fixing in pipe line etc.

complete. Item to be approved by engineer incharge or consulting engineer

43 Providing and fixing Kitchen sink make cera/hindware/Kohler/Jaquar etc or 2.00 Each 7699.91

similar with C.I. or M.S. brackets, painted white including cutting holes in walls

and making good the same . (C) Vitreous China Sink.(i) 600mm x 450mm x

150mm size.with fittings(ii) Flat Back washbasin 550 mm x v 400mm size. (i)

In white colour.a)Providing and fixing C.P. brass waste for washbasin or sink.

(A) 32mmdia. b)Providing and fixing M.I. fisher union for washbasin or sink.

(A) 32mm dia. c)Providing and fixing pillar tap, capstan head, screw down high

pressure with screws, shanks and back nuts. (i) 15mm dia.d)Providing and

fixing brass screw down stop tap.(A) 15mm dia.e)Providing and fixing Rubber

plug for sink or wash basin.

44 Providing and fixing Bib Cock ( Bib Tap ) make cera/hindware/Kohler/Jaquar 8.00 Each 1010.00

etc or similar with wall flange & aerator. Item includes all labour, material and

other cost. (ii) 15mm dia. Item to be approved by engineer incharge

45 Constructing brick masonry chamber for underground C.I. Inspection chamber 6.00 Each 2932.93

and bends with bricks having crushing strength not less than 35Kg/Cm2 in C.M.

1:5 C.I. cover with frame (Light duty) 455mm x 610mm intenal dimensions total

weight of cover with frame to be not less than 38Kg. (Wt. of cover 23 Kg.) and

Wt. of frame 15Kg. ) (R.C.C. top slabe with 1:2:4 mix (1-cement :2- coarse sand

:4-graded stone aggregate 20mm size) foundation concrete 1:5:10 inside plaster

15mm thick with cement mortar 1:3 finished smooth with a floating coat of neat

cement on walls and bed concrete etc. complete.(i) Inside dimensions 455mmx

610mm and 450mm deep for single pipe line.

46 Providing and fixing S.W. gully trap with C.I. grating brick masonry chamber 4.00 Each 1292.19

and water tight C.I. cover with frame of 300mm x 300mm size (inside) with

standard weight.(i) Square mouth traps. (A) 100mm x 100mm size P type.

47 Providing and fixing PVC SWR Nahni trap IS 14735 for drain - 100 mm 6.00 Each 585.37

diameter with jali of the following nominal diameter of self cleansing design with

C.I scread down or hinged grating including the cost of cutting and making good

02. Sch B_KPY_Pkg.6 Page

Item of work Quantities Rate in Amount

Estimated Unit Figures in

48 Providing laying and jointing in true line and level 15mm dia. U.P.V.C. Pipe ( 20.00 Rmt 72.65

SCH- 40) for cold water including fittings make PRINCE / SUPREME /

ASTRAL / FINOLEX or equivalent as approved by Engineer In Charge. Pipe

shall be fixed on the wall with the help of clamp at every two metre C/C or shall

be concelled as directed including necessary fittings etc. including testing of pipe

and joints and fixing the same with adhesive solvent, including cost of all

49 Providing laying and jointing in true line and level 25mm dia. U.P.V.C. Pipe ( 20.00 Rmt 91.84

SCH- 40) for cold water including fittings make PRINCE / SUPREME /

ASTRAL / FINOLEX or equivalent as approved by Engineer In Charge. Pipe

shall be fixed on the wall with the help of clamp at every two metre C/C or shall

be concelled as directed including necessary fittings etc. including testing of pipe

and joints and fixing the same with adhesive solvent, including cost of all

50 Providing laying and jointing in true line and level 40mm dia. U.P.V.C. Pipe ( 20.00 Rmt 148.12

SCH- 40) for cold water including fittings make PRINCE / SUPREME /

ASTRAL / FINOLEX or equivalent as approved by Engineer In Charge. Pipe

shall be fixed on the wall with the help of clamp at every two metre C/C or shall

be concelled as directed including necessary fittings etc. including testing of pipe

and joints and fixing the same with adhesive solvent, including cost of all

51 Providing and fixing to wall ceiling and floor 6.0 Kg. F/Cm2 working pressure 26.00 Rmt 211.09

poluthene pipes of the following outside Dia. Low densidy, complete with special

falnge compression type fittings, wall clipsetc. including making good the wall

ceiling and floor 75 mm Dia

52 Providing and fixing to wall ceiling and floor 6.0 Kg. F/Cm2 working pressure 12.20 Rmt 326.23

poluthene pipes of the following outside Dia. Low densidy, complete with special

falnge compression type fittings, wall clipsetc. including making good the wall

ceiling and floor 110 mm Dia

53 Providing and fixing to wall ceiling and floor 6.0 Kg. F/Cm2 working pressure 30.00 Rmt 681.75

poluthene pipes of the following outside Dia. Low densidy, complete with special

falnge compression type fittings, wall clipsetc. including making good the wall

ceiling and floor 160 mm Dia

54 Providing and fixing Gun metal check or non-return fullway wheel valve.(C) 4.00 Each 420.63

55 Providing and fixing Gun metal check or non-return fullway wheel valve.(E) 2.00 Each 663.43

56 Providing and fixing 600mm x 450mm bevelled edge mirrror of superior glass 4.00 Each 854.58

mounted on 6mm thick A.C. sheet or plywood sheet and fixing to wooden pluge

with C.P. brass screws and washers.

57 Providing and fixing C.P. brass towel rail comlete with C.P. brass brackets fixed 2.00 Each 616.42

to wooden plugs with C.P. brass scews.(B) 600mm x 20mm size.

58 Providing and fixing toilet paper holder.(A) C.P. Brass 2.00 Each 427.99

59 Providing and fixing pre-cast Rubber Dye / steel Dye inter locking concrete 35.26 Sqm 685.42

block or tactile pavers 60mm thick with grade of concrete M300 pnumatic

compressed / vibrated mechanically and as per approved design Confirming to IS

15658 : 2006 including 35 mm Sand layer for levelling and filling the joint with

sand in proper line and level as per guidlines of IRC : SP 63-2018 etc. Complete.

60 Providing Sandwitch Type Platform Using 25mm thick Single Polished kotah 6.26 Rmt 3764.27

stone 75 cm Width at Top Width 16 to 18 mm Thick Premium Black Grenite

Stone at Top with 75 mm Width and Face Patta Maximum 3.0 Mtr Long In

Single Piece using Cement Mortar 1:4 ( 1 cement : 4 coarse sand ) laid by 75 cm

width & 75 cm High Resting On 25 mm Thick One Side Polished kotah stone

fixed in wallc Cement Mortar 1:4 ( 1 cement : 4 sand ) at Bottom Polished

Kotah stone flooring including fixing grenite stone & cutting the stone for Fixing

suitable fixtures/ sanitary etc. if required with Polished & Including Providing

Premium Black Polished Grenite Stone 16 to 18 mm Thick with round Border the

edge,cost of sink. S S Grating Jali for nahni Trap, Brass Waste Coupline ,PVC

Waste Pipe, Manking Grove in Tile & Wall for Flooring Kotah Stone & Granite

....etc.Complete as per Drawing & Directed by Engineer in charge or consulting

02. Sch B_KPY_Pkg.6 Page

Item of work Quantities Rate in Amount

Estimated Unit Figures in

61 Providing & erecting Approved make Power Saving 50 Watt Ceiling Fan with 8.00 No 2297.75

double ball bearing ISI mark with Condenser 230 volt A.C. 50 Hz 1200 mm

sweep complete having 3blades with aluminium blades with , canopy & 30 cm.

down rod erected with earthing.(Make shall be approved by Engineer in charge))

62 Providing and erecting decorative wall bracket fittings complete with LED lamp 8.00 Rmt 2020.00

and rust free fittings components mounted in chrome finish housing with holder

,clear/opaque glass diffuser complete erected with lead wires with minimum

wattage capacity as per instruction engineer incharge/architect/authority .cat-III

63 Providing And Installation of LED TV As per directed by engineering incharge 2.00 Rmt 7575.00

64 Providing And Installation of Water Purifier As per directed by engineering 2.00 Rmt 8080.00

Credit For Reuse Material from Dismentalling & Diversion will be Deducted From respective 1st R.A. Bill Of

I / We am / are willing to carryout the work at ………..% above/Below percent (………………………. Percent above/Below)

Estimated amount put to tender Rs: ……………. Estimated amount put to tender Rs: …………...

Deduct……% below Rs: …………………………. Add……% above Rs: ………………………….…

(Please strike out which ever is not applicable.)

1 The Contractor shall exhibit a board with detailed specification and details of work as directed by the Engineer-In-Charge

2 The labour cess will be deducted as per prevailing rules i.e. 1% of the work done.

3 GST and Income tax TDS will be deducted at a source while making payments of bills

4 In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per Govt. G.R.: PRC-10/2017

5 Credit of Dismentalled /Reuse materils amounting of Rs. 45885.12 Must be fully recovered from respective 1st R.A. Bill

Quantities rate and wordings of items are as per estimate and calculation in the Sch. - B are airthmatically checked.

Above all items of "Schedule-B" with Item Description, Unit, Rate & Amount have verified by me and found order.

Sr.Divisional Account Officer Dy.Executive Engineer

Panchayat (R & B) Division Panchyat (R & B) Sub Division

Signaturre of contractor Executive Engineer

with seal Panchayat (R & B) Division

02. Sch B_KPY_Pkg.6 Page