ADDN ALTN TO CERTAIN OFFERS AND JCOs ORs MD ACCN IN CLEMENT TOWN DEHRADUN

Amount

BUILDING WORKS

Demolition of cement concrete (un-reinforced) in Ground floors and paving n.exc 15 cm thickness ( below or above ground level ) and including removing unserviceable material,outside defence land complete all as specified and directed.

M & L 40mm thick PCC (1:2:4) type B-1 (using 20mm graded stone aggregate) laid in panels as in flooring including finishing top surfaces even and fair without using extra cement complete all as specified and directed

Supply only glass dividing strips 3mm thick 38mm wide complete all as specified and directed

M & L for red stone slab 25 mm to 30 mm thick dressed true and square in one length not less than 60 cm and n. exc 120 cm in plinth protection / hardstanding over and including 20 mm thick screed bed in cm 1:4 over 75 mm thick PCC (1:3:6) type C-2 (Using 40mm graded stone aggregate) laid in panels, finished the surface even and rough complete all as specified and directed(Note-Expansion joints 12 mm width provided every 3 mtr, Expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade ‘A)

Demolition of cement concrete (reinforced) of any position not otherwise specifically provided for and including reinforcement required to facilitate demolition upto and including on the roof top/mumty/parapet/RCC chajjas/RCC water tank and removing unserviceable material,outside of A 1 defence land complete all as specified and directed.

M & L RCC (1:2:4) type B-1 (Using 20mm graded stone aggregate) as in slabs, shelves supported on walls, beams and columns in floor or roof including balconies, canopies, deck slabs or in Chajja / facia projection and the like complete all as specified and directed Note : The work is required to be carried out upto Second storey building. The cost of scaffolding shall be deemed to be included in the item. The contractor shall also make necessary safety arrangement for labour.

M & L for mild steel TMT bars 10mm dia and over, cut to length bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed

Use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick for fair finished surfaces (Horizontal or sloping) complete all as specified and directed.

Demolition of brick work built in cement mortar in any description and position including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

M & L brick work with sub class 'B' bricks, straight or curved on plan exceeding 6m mean radius built in CM (1:6) complete all as specified and directed.

M&L brick work with sub class 'B' bricks, straight or curved on plan to any radius in half brick thick walls built in CM (1:4) ,complete all as specified and directed.

Taking down chowkhats or frames of any description with shutters (without taking off shutter from the frames) not exceeding 1.5 Sq.m each.Complete all as specified and directed

Taking down chowkhats or frames of any description with shutters (without taking off shutter from the frames) exe 1.5 Sqm but not exceeding 4.0 Sq.m each.Complete all as specified and directed.

M & L for PCC 1:3:6 type C1 (using 20mm graded aggregate stone aggregate) as in hold fast blocks including filling of pressed steel framing and complete all as specified and as directed.

M&L for Factory made solid WPC Door frame (125mm X 63mm Double Rebate) made from 100% LEAD FREE (Single extruded process) material with density 780kg / Cum and manufactured by an ISO : 9001-2015 certified company, all as per specification drawings as directed by the Engr-in-Charge. The door frame should be water proof, Termite proof, Fire retardant and having excellent, fixed with fasters with sufficient holding capacity complete all as specified and directed

M&L for Solid factory made 100% solid WPC brown door frame (100mm X 63mm single rebate) made from 100% LEAD FREE (Single extruded process) material with density 780 kg / Cum & manufactured by an ISO: 9001-2015 certified company, all as per specification drawings as directed by the Engr-in-Charge The door frame should be water proof, termite proof, fire retardant and having excellent, fixed with fasters with sufficient holding capacity complete all as specified and directed .

M&L Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge),minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: stainless steel butt hinges and necessary S S screws shall be paid separately)

S & F 35 mm thick factory made flush shutter solid core construction with block board core and ply wood face panels, commercial type both sides complete all as specified and directed.

S & F 0.90 mm thick decorative laminates surface finish one side,colour and pattern as approved,fixed with approved adhesive as per manufacture instructions complete all as specfied and as directed.

S & F 35 mm thick 2nd class hard wood factory made glazed and skeleton shutter, open rebated and prepared to receive glass, gauge etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats and complete all as specified and directed.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanized wire staples complete all as specifed and directed

M & L 5.5mm thick sheet glass ordinary quality and fixed to wooden doors with wooden beads or tinned tacks in square not exc 0.5 sqm each pane complete all as specified and directed.

S&F three track Pre coated Steel Sliding Window System fabricated from roll formed sections made of Galvanized Steel Colour Coated/ Powder Coated (Base Steel as per IS 513 “D” quality, galvanized as per IS 277 with Zinc of 120 grams/ Sq. Mtr.) with total coated thickness of 0.58 mm or Powder Coated with pure Polyester Powder up to 50-60 microns thick. Windows Section for three track external frame should be of 44 x 107mm , Section for window glass shutter should be of 36 x 50 mm, if required Section for shutter horizontal mullion should be 22mm x 60mm, The windows should be paneled with 5mm thick Plain Float glass Gaskets are to be made with Ethyl Propylene Diamine Manomer (EPDM). Corner brackets for internal and external frame made of Polypropylene. Touch lock to be provided for window shuttes Sections are to be cut to length, joined and assembled by means of corner brackets.

The above Frame should be fixed to brick/ concrete masonry by using Nylon self-expanding caps and driving MS electroplated 80mm long screws into the caps through frames.Windows shall be provided with fixed Stainless steel 32 gauge wire mesh/gauze of 304 grade with 144 holes per square inch for mosquito proofing with the help of nut, bolt and flat iron of 20x3mm size on top and Grill made of 10mm MS Square bars welded to 25x4mm angle iron . Distance between bars should not be more than 110mm centre to centre horizontally. Total Grill and wire mess unit shall be powder coated.Assembling and installation of windows and ventilators shall be all as per details shown/mentioned on drawings and as per manufacturer‟s instructions.complete all as specified and directed.

S & F Pre coated Steel fixed type Window / ventilator fabricated from roll formed sections made of Galvanized Steel Colour Coated / Powder Coated (Base Steel as per IS 513 “D” quality, galvanized as per IS 277 with Zinc of 120 grams / Sq. Mtr.) with total coated thickness of 0.58 mm or Powder Coated with pure Polyester Powder up to 50-60 microns thick. The windows should be paneled with 5mm thick frosted glass Gaskets are to be made with Ethyl Propylene Diamine Manomer (EPDM). Corner brackets for internal and external frame made of Polypropylene. The above Frame should be fixed to brick / concrete masonry by using Nylon self-expanding caps and driving MS electroplated 80mm long screws into the caps through frames. Windows shall be provided with Grill made of 10mm MS Square bars welded to 25x4mm angle iron . Distance between bars should not be more than 110mm centre to centre. Total Grill shall be powder coated.Assembling and installation of windows and ventilators shall be all as per details in manufacturer‟s instructions complete all as specified and directed.

Blank

S & F for stainless steel barrel tower bolt (AISI 316 grade) of size 12 mm dia and 200 mm length Complete all as specified and directed

S & F for stainlees steel sliding door bolt (AISI 316 grade) of size 16 mm dia and 250 mm long with hasp, staple (bolt type) complete all as specified and directed.

S & F stainless steel handle (AISI 316 grade) of size 150 mm complete all as specified and directed.

S & F for stainless steel barrel tower bolt (AISI 316 grade) of size 12 mm dia and 150 mm length Complete all as specified and directed.

S&F 150 mm size floor door stopper of aluminium body and tongue with hard drawn steel spring spring, fixed in floor complete all as specified and directed

S&F mild steel 300 mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed

Dismantling Boarding any description fixed in any position with nails complete all as specified and directed.

S & F 18 mm thick with min density 600 Kg / Cum LEAD FREE PVC Celuka ply of both side plain white colour fixed with screws, solvent cement/ adhesive to make kitchen/bed rooms cabinet sides top and bottom and shelves inside the cabinets complete as per manufacturer’s specifications complete all as specified and directed.

S & F 18 mm thick with min density 600 Kg / cum LEAD FREE PVC Celuka ply of single side rigid laminate of approved color and other side plain white colour fixed with ss screws and solvent cement/ adhesive to make kitchen cabinet shutters complete as per manufacturer’s instructions complete all as specified and directed.

S & F 6 mm thick with min density 600 Kg / cum LEAD FREE PVC ply fixed with ss screws and solvent cement / adhesive to make wall mount kitchen cabinet back sides complete as per manufacturer’s specifications complete all as specified and directed

S & F in repairs for hasp and staples, size 150 mm, safety type, aluminium anodized with mild steel hinge pin including bolt to hinge plate and fixed with screws, Complete all as specified and directed

S & F Auto closing hinges 35 mm of 0 crank ( KH-001) or 8 crank (KH-002) openable at 110 degree for kitchen cabinet shutters complete in all respect and fixed in position all as specified and directed.

S & F Ball bearing runners 400 mm Telescopic (KA 5632) full extension load capacity 45 kgs complete all as specified and directed.

S & F D-type cabinet handles premium quality, stainless steel 304 / gloss chrome / SN finished 150 mm long matt finished complete fixed in position complete all as specified and directed.

S & F Ball catchers 304 grade stainless steel finished suitable for cabinets premium quality complete fixed in position as per manufacturer's instructions complete all as specified and directed.

S & F Stainless Steel 304 grade wire Basket of pull out type like lain / cup & saucer / bottle / multi purpose / 2-3 shelf baskets etc for kitchens of required sIze complete fixed in position all as specified and directed.

S&F in repair for stainless steel, 25 mm dia and 1.2 mm thick curtain rod with and including fixing SS brackets and decorative type SS knobs both side of each rod, complete all as specified and directed Note Measurement will be taken between end points of Knobs.

M & L for Mild steel framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 Gde E-165. Complete all as specified and directed

S & F Welded steel wire fabric weight n exc 4 kg / sqm fixed to wood or steel members complete all as specified and directed

S & F Rolled mild steel work of Fe-290 (Gde E-165) as in framed work, trussed, purlins, crane gantries, railS&Fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc complete all as specified and directed.

Taking down existing tar felt and plastering from the roof surface washing down and cleaning the surface with water and rubbish off the premises and M&L 15mm thick cement plaster (1:4) for finishing existing surface and over laying water proofing treatment on top surfaces of roof after cleaning of roof surfaces with water and filling cracks with sealing compound and dried top surface of roof. Apply a coat of cold bituminous primer @ 0.30 liter per Sqm and followed by a layer of APP polymer modified five layered water proofing membrane 3mm thick weight not less than 3.60 Kg/Sqm with non woven polyester reinforcement (weight not less than 150 gm/Sqm) of M/s STP Texsa Ltd or M/s IWL (I) Ltd or M/s STP Ltd. The APP membrane shall be laid with LPG connected torch method.

A layer of hot blown bitumen grade 85/25 @ 1.20 Kg/Sqm and a layer of bituminous aluminum paint as final finish @ 0.20 Kg/Sqm shall be applied on top surfaces of APP membrane, Application including overlap, side lap shall be provided as per manufacturer instructions and as specified and directed The side lap and end laps should have overlap of 75mm to 100mm and should be thermo fused together so that it forms a single sheet through out complete all as specified and directed by Engr-in-Charge Note:- The work is required to be carried out at non-accessible roof for double storey .The contractor shall make arrangement of scoffolding,safety & security of workers and arrangement for approach to roof . The rates quoted shall deemed to be included for these items

M & L 50 mm +/- 25mm thick PCC 1:2:4 type B-0 (using 12.5 mm graded stone agg) mixed withliquid water proofing compound (as per manufacture direction and paid separately) over and incl one coat of cement slurry admixed with acrylic bonding compound SBR Latex liquid polymer as to be used for bonding of new concrete / mortar to old surface as per manufacturer direction and finishing the surface even and fair (without using extra cement) as in roof padding to receive roof treatment complete all as specified and directed.”complete all as specified and directed. Note :- The work is required to be carried out at non-accessible roof for double storey . The contractor shall make arrangement of scoffolding,safety & security of workers and arrangement for approach to roof . The rates quoted shall deemed to be included for these items .

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing), removing and rubbish off the premises from MoD all as specified and directed.

M & L Light coloured vitrified tiles of any design and pattern, 1200 x 600 x 9 to 10 mm thick as in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles. Tiles shall be conforming to IS-15622:2017, Group B1b and including 15mm thick screed bed in Cement mortar (1:6) in flooring, set and jointed in neat cement slurry and pointed in coloured cement to match complete all as specified and directed by Engr-in-Charge .

M & L Light coloured vitrified tiles of any design and pattern, 1200 x 600 x 9 to 10 mm thick as in vertical surfaces / skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles. Tiles shall be conforming to IS-15622:2017,Group B1b and including 10mm thick rendering in Cement mortar (1:4), set and jointed in neat cement slurry and pointed in coloured cement to match complete all as specified and directed by Engr-in-Charge.

M & L for Non- skid coloured ceramic tiles of any design and pattern, 7 to 8 mm thick (square / rectangular) area of each tile exe 0.11 sqm but not exe 0.18 sqm, in floor etc incl 15mm thick screed bed in CM 1:6, Set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles . Tiles shall be confirming to IS-15622.2006, Group B II Complete all as specified and directed Note:- Shade of the tiles including Colour, design and pattern shall be approved by GE.

M & L for Non-skid coloured ceramic tiles of any design and pattern, 7 to 8 mm thick (square / rectangular) area of each tile exe 0.11 sqm but not exe 0.18, as in dado/skirting etc incl 10 mm thick rendering in CM 1:4 Set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles . Tiles shall be confirming to IS-15622.2006, Group B II Complete all as specified and directed. Note:- Shade of the tiles including Colour, design and pattern shall be approved by GE.

M & L for Non- skid coloured ceramic tiles of any design and pattern, 7 to 8 mm thick (square / rectangular) area of each tile exe 0.06 sqm but not exe 0.11 sqm, in floor etc incl 15mm thick screed bed in CM 1:6, Set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles . Tiles shall be confirming to IS-15622.2006, Group B II Complete all as specified and directed. Note:- Shade of the tiles including Colour, design and pattern shall be approved by GE.

M & L for coloured glazed ceramic tiles of any design and pattern, 450X 300X 7mm thick, set and jointed in neat cement slurry and pointed in white or colour cement to match incl 10 mm thick rendering in CM 1:4, complete all as specified and directed. Note: Shade of the tiles including Colour, design and pattern shall be got approved by GE .

M & L Light coloured vitrified tiles of any design and pattern, 600 x 600 x 9 to 10 mm thick as in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles.Tiles shall be conforming to IS-15622:2017, Group B1b and including 15mm thick screed bed in Cement mortar (1:6) in flooring, set and jointed in neat cement slurry and pointed in cloured cement to match complete all as specified and directed directed by Engr-in-Charge . Note:- Shade of tiles including colour, design and pattern shall be approved by GE.

M & L Light coloured vitrified tiles of any design and pattern, 600 x 600 x 9 to 10 mm thick as in vertical surfaces / skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles.Tiles shall be conforming to IS-15622:2017,Group B1b and including 10mm thick rendering in Cement mortar (1:4), set and jointed in neat cement slurry and pointed in cloured cement to match complete all as specified and directed directed by Engr-in-Charge. Note:- Shade of tiles including colour,design and pattern shall be approved by GE.

Blank

Blank

M&L Pre-polished Baroda green marble 16-18 mm thick (table rubbed and polished) in step, jambs, pillars , window cills, cooking platforms and the like in CM 1:4 incl pointing in white cement 1:2 using marble dust with admixture of pigment to match with marble including half round moulding and making hole for gas pipe (where required) over and incl 15mm thick screed bed in CM 1:6 complete all as specified and directed

Blank

M & L for 25mm thick PCC (1:2:4) type B-0 (using 12.50mm graded stone aggregate) as in sub base of floor complete all as specified and directed

M & L 75 mm thick PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in sub base of floor complete all as specified and directed

Taking down cement plaster, terrazzo dado in any thickness from brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc and removing unserviceable material outside of A 1 defence land complete all as specified and directed.

M & L Rendering 15 mm thick on fair faces of brick work or concrete walls internal surfaces in CM 1:6 finished to even & smooth without using extra cement. Complete all as specified and directed.

M & L plastering in two layers consisting of 10mm thick in CM 1:6 and top layer of 5mm thick in CM 1:4 mixed with liquid water proofing compound on fair faces of brick work or concrete surfaces, finished the surfaces even and fair without using extra cement complete all as specified and directed. (WPC shall be measured and paid seperately)

M&L for two coats of oil bound distemper over a coat primer to newly plastered surface including preparation of surfaces complete all as specified and directed

M&L for applying 3mm thick wall care putty on wall complete all as specified and directed

M&L Complete removal of existing treatment to wall (internal) surfaces in any height for two coatss of oil bound distemper on walls over a coat of primer to old plastered surface complete all as specified and directed.

Material & Labour for applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance,dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10sqm over new surfaces complete all as specified and directed.

M & L rendering 5 mm thick in CM 1:3 in ceiling / Chhajja's finished even and smooth (without using extra cement). Complete all as specified and directed

M & L for preparation of new surface plastered or unplastered and applying three coat of white wash on ceiling all as specified and as directed by Engr-in-Charge.

M & L Preparation old treated surfaces of walls and applying one coat of white wash complete all as specified and directed.

M & L Preparation old treated surfaces of ceiling and applying one coat of white wash complete all as specified and directed.

M & L for prepairing old painted steel and Iron surfaces of any description over 10 cm Width / Girth and applying one coat of synthetic enamel paint of any tint complete all as specified and directed.

M&L for complete removal of old surface for applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance,dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10sqm over old surfaces complete all as specified and directed.

Complete removal of existing treatment by electric grinder and fill the cracks by smartcare crack seal of Asian paint and apply fresh coat of Damp Proof ultra mixed in ratio of 3:1 and applied with a spreading rate of 5.5 Sq meter / Ltr (60 sq feet / ltr). Allow to dry for 4-6 hours and then apply another coat of Damp Proof ultra without dilution with a spreading rate of 4.6 to 5.1 Sq meter/Ltr (50-55 sq feet / ltr), all as per manufacturar instruction Complete all as specified and directed

M & L for preparation of new steel surfaces of any description over 10cm width & girth not otherwise described and applying two coat of synthetic enamel paint over a coat of red oxide primer. Complete all as specified and directed

M & L for Preparation of New wood and wood based surfaces of any description not otherwise described over 10 cms width or girth and applying 2 coats of synthetic enamel paint (any tint) over a coat of pink primer. Complete all as specified and directed

M & L PCC 1:5:10 type E-2, using 40 mm graded concrete, as in foundation, mass concreting, sunken floor etc complete all as specified and directed

M & L PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate, as in padding, sunken, coping portion rounded chamfered on edge complete all as specified and directed.

M & L 10 mm thick rendering in cement mortar (1:4) mixed with liquid water proofing compound on fair faces of brick work or concrete surfaces, finished the surfaces even and fair without using extra cement complete all as specified and directed. Note :- WPC shall be measured and paid seperately.

Supply only liquid water proofing compound complete all as specified and directed.

M & L for two coats of elastomeric compound i.e. super latex of Dr. Fixit or equivalent on concrete surfcae after cleaning of sunken portion (vertical or Horizontal) by removing all the loose mortar, laitance dirt, dust etc by chiesal, hammer, wirebrush, jute brush and air blower complete all as specified and directed

Supply and Fixing 40 mm dia GI light grade pipe as in spout of sunken slab complete all as specified and directed.

Taking up or down steel water tubing and connections including cleaning for refixing or removing to store 15 mm dia .Complete all as specified and directed

S & F for GI tubing 15mm bore, medium grade with all fittings (such as bends, elbows, Tee short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions, including short lengths etc.) fixed to walls, concealed in wall and ceiling or laid in floor complete complete all as specified and directed. Note:- Cutting chases in wall shall be measured and paid seperately.

M & L for cutting chases on brick or concrete surface for concealed water tubing or / similar work of girth n.exc 10cm including making good of disturbed surfaces with PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate complete all as specified and directed.

Taking up or down steel water tubing and connections including cleaning for refixing or removing to store 20 mm dia .Complete all as specified and directed.

S & F for GI tubing 20mm bore, medium grade with all fittings (such as bends, elbows, Tee short pieces, connectors, back nuts, diminishing pieces, caps and plugs,unions etc.) including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete . complete all as specified and directed. Note:- Cutting chases in wall shall be measured and paid seperately.

Fixing only 20 mm dia bore GI tubing medium grade fixed to wall or ceiling or laid in floors etc complete all as specified and directed

S & F in repair 110 mm bore PVC (SWR) Soil, waste and vent pipes, single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed.

S & F in repair 110 mm bore PVC (SWR) Soil, waste and vent pipes, single socketed in any length with rubber ring joints fixed to wall complete all as specified and directed.

S & F in repair 75 mm bore PVC (SWR) Soil, waste and vent pipes, single socketed in any length with rubber ring joints laid in trenches or in floors.complete all as specified and directed.

S & F in repair 75 mm bore PVC (SWR) Soil, waste and vent pipes, single socketed in any length with rubber ring joints fixed to wall complete all as specified and directed.

S & F in repair 75 mm dia PVC (SWR) multi floor trap, with grating including jointing with solvent cement including fixing waste pipe etc complete all as specified and directed

S & F in repair PVC (SWR) junction single, (Single T) equal or unequal 110 mm bore with access door complete all as specified and directed.

S & F in repair PVC (SWR) junction single, (Single T) equal or unequal 75mm bore with access door complete all as specified and directed.

S & F in repair 110 mm bore PVC (SWR) bends of any radius complete all as specified and directed.

S & F in repair 75 mm bore PVC (SWR) bend of any radius complete all as specified and directed.

S & F in repair PVC (SWR) bend any radius 110 mm bore with access door complete all as specified and directed.

S & F in repair PVC (SWR) bend any radius 75 mm bore with access door complete all as specified and directed.

S & F in repair PVC (SWR) 'P' Traps 110mm bore.complete all as specified and directed.

S & F in repair PVC vent cowls 75mm. complete all as specified and directed.

S & F in repair for PVC Connections 15mm size with PTMT nuts of length 450 mm B. Complete all as specified and directed

S & F in repair PVC waste pipe 32 / 40 mm dia complete all as specified and directed

S & F cast copper alloy, chromium plated Towel Rail 20 mm dia, D-type, 600 mm long fixed with and including Chromimum plated brass screws and wooden plastic cleats Complete all as specified and directed .

S & F in repair bib tap cast copper alloy with crutch or butter fly handle, screwed down for iron pipe 15 mm bore of tubing fancy type cromium plated. complete all as specified and directed.

S & F in repairs stop valve cast / angle cock copper alloy screwed down high presure (concealed type) screwed both end for iron pipe 15 mm dia fancy type cromium plated. complete all as specified and directed.

S & F in repair vitreous china white wash hand basin with pedestal flat back of size 550 x 400mm including CI / MS brackets including cutting for and pinning in brackets but including waste fittings complete all as specified and directed.

S & F in repair of sinks made of stainless steel 1.0 mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 495mm x 420mm and bowl size 410 mm x 330 mm x 160 mm complete all as specified and directed.

S & F in repair vitreous china squatting pan ‘Orissa pattern’ size 580 x 440 mm white with integral foot rest including connection to trap, and flushing pipe, anti-syphonage pipe, etc and including lime concrete bedding complete all as specified and directed.

S & F in repairs PVC valveless, syphonic action type flushing cistern (Dual action ), low level , white, with inlet ball valve, float and handle including brackets and flush pipe suitable for IWC of polyethylene of low or high density or PVC 32 mm dia for low level cistern for 10 litres capacity of approved make Complete all as specified and directed.

S & F in repair vitreous china wash down water closet pan single piece (pedestal pattern) size 365 x 655 x 760mm UF soft close seat cover fixing accessories set and accessories set cistern fittings and S trap 220mm complete all as specified and directed.

Supply & fix in repair wall mixer with over head shower chromium plated for mixing hot and cold water screwed for iron pipe suitable for 15 mm bore pipes complete all as specified and directed .

S & F in repair 15mm dia brass CP sink mixer with swinging spout (wall mounted model) with connecting legs and wall flanges screwed down for iron pipe and fixed complete all as specified and directed .

S & F in repair 15mm dia chromium plated central hole wash hand basin mixer without PWS with 450mm BRAIDED HOUSE hose screwed down high pressure screwed for iron pipe completed all as specified and directed .

S & F in repair CP health faucet with 1m flexible tube and wall hook complete all as specified and directed.

S & F in repairs angle stop valve cast copper alloy screwed down high presure screwed both end for iron pipe 15 mm dia fancy type cromium plated. complete all as specified and directed.

S & F in repair brass CP bib tap 15mm bore fancy type screwed for iron pipe complete with wall flange complete all as specified and directed.

S & F in repair CP overhead shower 100mm round shape single flow (ABS body chromium plated with gray face plate) with rubit cleaning system fixed in 15mm bore of pipe complete all as specified and directed .

S & F in repair CP toilet paper holder fixed to wall with CP brass screws complete all as specified and directed.

S & F for Glass shelf with Sheet Glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60 cm long Complete all as specified and directed

S & F in repairs PVC water storage tank triple layer cylindrical, vertical with closed top with threaded cover hoisted and fixed in position tank capacity 500 Ltr with and including ball valve high pressure of PTMT with epoxy coated Aluminum rod and high density plastic ball screwed for 20mm bore of iron pipe and making connection for inlet and outlet including dismantle of old water tank and removing from site complete all as specified and directed

S & F in repairs PVC water storage tank triple layer white colour cylindrical, vertical with closed top with threaded cover hoisted and fixed in position tank capacity 1000 Ltr with and including ball valve high pressure of PTMT with epoxy coated Aluminum rod and high density plastic ball screwed for 25mm bore of iron pipe and making connection for inlet and outlet including dismantle of old water tank and removing from site complete all as specified and directed

S & F in repair 15 mm dia Gun Metal, globe or Gate Valve class 150 with Iron wheel head Screwed both ends for Iron Pipe and Complete all as specified and directed

S & F in repair 20 mm dia Gun Metal, globe or Gate Valve class 150 with Iron wheel head Screwed both ends for Iron Pipe and Complete all as specified and directed

M & L for post construction Antitermite treatment Along the wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc in apron complete all as specified and directed.

S & F Stainless steel kitchen plate rack 1.0 mm thick sheet of over all size 750 x 900 x 250 mm fixed with steel screws and steel rawal plugs complete all as specified and directed.

M & L butt hinges of mild steel medium weight cold rolled 100mm long and fixed with screws to timber frame work complete all as specified and directed

M & L 16 to 18 mm thick pre polished granite stone slab of approved quality on cooking platform over and incl 20mm thick cement mortar in 1:6, bedded and jointed with cement mortar and pointed in white cement mortar 1:2 complete all as specified and directed.

M & L MS Work confirming to Fe-290 Gde E-165 as in Bands strapes stays hold fast and similar small articles complete all as specified and directed.

M & L for factory made single extruded WPC (Wood polymer composite) solid plain flush door shutter of 18 to 20 mm size comprising of virgin polymer of K-value 58-60 (suspension grade), calcium carbonate of natural fibres ( wood powder / rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 Kg / Cum and screw withdrawl strength of 1800 N (face) & 900 N (edge), minimum compressive strength of 50N/mm2 and modulus of elasticity 850N/mm2 and resistance to spread of flame of class A catagory with property of being termite / bored proof, water / moisture proof and fire retardent fixed with stainless screws to timber framework complete all as specified and directed.

S & F in repair corner self 300mm radius of 5mm thick toughened glass with CP railing with bracket S & Fixed with brass screw complete all as specified and directed .

M&L for Providing precast cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) in landings, cover slabs (for man holes etc.) chullah hoods, chajjas,water troughs, mangers, shelves and similar articles complete all as specified and directed .

M&L dura stone tiles approved make of size 300x300x8mm thick as in floor over and including 15mm thick screed bed in Cement mortar (1:4) including 75 mm pcc sub base in proportion 1:4:8 type D2, set and jointed in neat cement slurry and pointed in coloured cement to match complete all as specified and directed by Engineer-in-Charge.

M&L for plain cement concrete 1:3:6 type C1 (using 20mm graded stone aggregate) as in surface channel or drain or benching in manhole complete all as specified and directed

M&L for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement including forms, moulds, mitered/stopped ends etc complete all as specified and directed

S&F for Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.5mm of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engineer-in-Charge.

S&F Joist, channel, angle, or tee sections,fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated conforming to Fe-410W (gde E-250) quality A complete all as specified and directed.

Excavation in post hole (or similar holes) each n. exc 0.5 cum, getting out, returning filling in and ramming earth or broken rubble mixed with earth around in layers n. exc 25cm, watering and removing surplus soil to a distance n. exc 50m and making good surface in any type of soil complete all as specified and directed

S& F stainless steel magic eye 2 inch length and 180 degree viewing angle including necessary fittings on WPC door complete all as specified and directed.

S& F stainless steel heavy duty security door chain lock of size not less than 300 mm length to be provided with necessary fittings with anti theft sliding chain lock with mounting screws on any type of door, complete all as specified and directed.

M & L for providing and fixing SS (grade 304) railing made of hollow tubes, channels, plates etc, including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and directed.

Dismantling and taking down carefully unservicable copper / aluminium point wiring (light, fan, socket, power) complete fitting such as switches, ceiling roses, pendants, lamp holder, light fitting etc including CI/Pressed steel terminals, switch box, and making good the disturbed surface of wall / floor etc, to match with the existing surfaces of wall / floor complete all as specified & directed.

Taking down submain / service / UG cable on wall / trenches / roof / floor etc complete all as specified and directed.

Dismantling and taking down carefully existing DB’s any type and making good the disturbed surfaces of wall/floor to match with the existing wall / floor etc. complete all as specified and directed.

M & L Point wiring with 1.5 Sqmm (Nominal area) FRLSH PVC insulated and unsheathed single core cable 1100 volts grade with stranded copper conductor in and including concealed rigid PVC conduit medium grade of size not less than 20 mm dia including accessories incl cutting chases , making surface good etc along with contineous earth wire 1.5 Sqmm FRLSH PVC insulated , unsheathed stranded copper conductor cable and connected to common earth dolly including metal flush box with white cover plate & frame for modular switch & socket complete with all accessories for complete all as specified & directed for the following:- (a) One light / fan / bell / exhaust fan point controlled by one, 01-way modular type switch 5/6 Amp.

All as per Srl Item No 150 above but one 5 Amp socket outlet on the same board with other switches / sockets

All as per Srl Item No 150 above but for One 5 pin 5/6 Amps socket outlet point on independent board controlled by one, 01-way modular type switch single pole 5/6 Amps.

All as per Srl Item No 150 above but one light point controlled by two, 02-way point wiring with two no of two way switch with cables 1.5 sqmm size in PVC conduit

M & L Point wiring with 2.5 Sqmm (Nominal area) FRLSH PVC insulated and unsheathed single core cable 1100 volts grade with stranded copper conductor in and including concealed rigid PVC conduit medium grade of size not less than 20 mm dia including accessories incl cutting chases and making surface good etc along with contineous earth wire 2.5Sqmm FRLSH PVC insulated , unsheathed stranded copper conductor cable and connected to common earth dolly, including metal flush box with white cover plate & frame for modular switch & socket complete with all accessories for (a) one three pin 15 Amps Switch Socket outlet on independent board

All as per Srl item No 154 above but with 4 Sqmm PVC insulated FRLSH cable for 15 Amps power point.

M & L Point wiring with 1.5 Sqmm (Nominal area) FRLSH PVC insulated and unsheathed single core cable 1100 volts grade with stranded copper conductor drawn in Existing concealed PVC conduit, along with contineous earth wire 1.5 Sqmm FRLSH PVC insulated , unsheathed stranded copper conductor cable and connected to common earth dolly including metal flush box with white cover plate & frame for modular switch & socket complete all as specified & directed for the following :- (a) One light / fan / bell / exhaust fan point controlled by one, 01-way modular type switch 06 Amp.

All as per Srl Item No 156 above but one 5 Amp socket outlet on the same board with other switches/sockets

All as per Item No 156 above but for One 5 pin 5/6 Amps socket outlet point on independent board controlled by one, 01-way modular type switch single pole 5/6 Amps.

M & L Point wiring with 2.5 Sqmm (Nominal area) FRLSH PVC insulated and unsheathed single core cable 1100 volts grade with stranded copper conductor drawn in Existing concealed PVC conduit, along with contineous earth wire 2.5Sqmm FRLSH PVC insulated , unsheathed stranded copper conductor cable and connected to common earth dolly, including metal flush box with white cover plate & frame for modular switch & socket complete with all accessories for complete all as specified and directed. (a) one three pin 15 Amps Switch Socket outlet on independent board

All as per item No 159 above but with 4 Sqmm PVC insulated FRLSH cable for 15 Amps power point.

Supply and fixing modular switch type 1 way 06 Amp, 1 Module, 240 Volts AC complete all as specified and directed.

Supply and fixing modular switch type 1 way 16 Amp, 1 Module, 240 Volts AC complete all as specified and directed.

Supply and fixing modular bell push 1 way 06 Amp, 1 Module type all as specified complete all as specified and directed.

Supply and fixing modular switch type 2 way 06 Amp, 1 Module, 240 Volts AC complete all as specified and directed.

Supply and fixing modular socket 06 Amp 3 pin combined, 2 module complete all as specified and directed.

Supply and fixing modular socket 06/16 Amp combined, 2 module complete all as specified and directed.

S&F bell ding dong elelctric 230V AC single pole complete all as specified and directed.

Supply and fixing modular fan regulator, 45 W, 2 module complete all as specified and directed.

S&F ceiling rose 3 terminal / PVC/ polycarbonate, isolated body complete all as specified and directed

Supply and fixing batton holder mounted on wall including 09 Watt LED Bulb complete all as specified and directed.

Taking down old ceiling fan from existing building and deposit to MES Store. complete all as specified and directed.

Taking down ceiling fan from existing building again refixing the same ceiling fan connecting up including provision of cable flexible 3 core of suitable size wire from ceiling rose to connect fan. complete all as specified and directed.

S & F LED tube light batten 20 watts 4 fts polycarbonate housing, translucent diffuser with LED light source , 2200 lumen, natural white ,surge protection range 2KV, voltage protection range 120-280 VAC , 2 years warranty ,system efficacy not less than 110 Lm/watt for the fitting , power factor>0.95 total harmonic distortation<20% , colour rendering index >80, coefficient colour temp 6500 K, fixed on site with all accessories all as specified and directed. LM79 and LM80 reports to be produced . BIS certification must .

S& F oval shape Bulk head Edge-lit LED fitting comprising with high brightness LED 10 watt, IP-67 protection complete all as specified and directed.

S & F Glaze Wall Light including 7/9 watt LED (B22) type all as specified and directed.

S& F Mirror Light LED fitting 10 Watt fitting (2 feet) complete all as specified and as directed.

Supply and fix LED street/security light fitting 20W housing made out of pressure die-cast aluminium alloy with toughned glass, IP-66 protection, working on 240 Volts AC, 50 HZ, consisting of reflective lens wired with approximate driver PF>0.98 having over voltage protection upto 440 volts, Surge protection level > 10 KV, thermal short circuit protection THD < 10% made up of long life LED chips (SMD) in modular with Ra>70, and LED lumen efficiency >140 lumen per watt, beam angle along the drive way, 120 degree, beam angle across the drive way, 80 degree luminior efficiency > 120 Lumens/watt power LED should be of more than 01 watt CCT should be between 5700 K- 6500 K including fixed on wall with 02 Nos MS clamp made out of 40 x 6 mm F1 and bracket made out of 32 mm dia light grade GI pipe not less than 0.9 mtr long bend to shape including connecting with 1.5 sq mm, 3 core, PVC insulated Copper conductor cable 1100 Volta grade all as specified and as directed by Engr-in-Charge Note :- (i) the firm has to give warranty for street light fittings including driver minimum for 03 years for any defects developed during the period. (ii) The contractor shall submit the third party LM 79 & LM 80 report from any NABL approved laboratory. (iii) The fitting should have BIS, CRS (iv) Connection to luminaire shall be done in suitable PVC connector within the bracket/luminaire end and are inclusive in above.

S & F double door sheet metal enclosure for DB , 08 way , SPN, with 200 Amps rated bus bar , 240 Volts suitable for housing MCBs and flushed inside the wall and making good for disturbed surface with existing etc complete all as specified & directed.

S & F double door sheet metal enclosure for DB , 12 way , SPN, with 200 Amps rated bus bar , 240 Volts suitable for housing MCBs and flushed inside the wall and making good for disturbed surface with existing etc complete all as specified & directed.

Supply and fix sheet metal enclosures with metal socket and plug top single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB SP 20,10 KA , Amps all complete as specified and directed by Engineer-in-Charge .

Supply and fixing MCB SP AC 240 volts of 6 to 32 Amps capacity 10 KA, 'B' series and making connections with suitable size of copper lugs complete all as specified and directed .

Supply and fixing MCB SPN 40 Amp 240 V AC 10 KA repturing capacity complete all as specified and directed.

Supply and fix electric water heater storage type ABS body with glass lined inner tank with digital temprature indicator and heating element upto 2KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve thermostate NRV connection piece including taking down old water heater storage type from existing building and deposit to MES Store including all as specified and directed.

S&F Exhaust fan AC single phase 230/240 Volt of size 300 mm sweep, metallic body powder coated painted finish, Power consumption- 50 W, Air deplacement -1290 Cum/Hr, RPM-900 complete with louvers including making whole and grouting of nut bolts etc and making good the disturbed sufaces of wall complete including taking down old exhuast fan any type from existing building and deposit to MES Store all as specified and directed.

Supply & fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250 mm sweep complete with all fittings all as specified.

Supply, installing, testing and commissioning factory made and tested LT Panel Indoor type Wall mounted, of size : 900 X 650 X 250 mm suitable for 415 Volts 3 Phase and neutral, 4 wire, 50Hz AC supply system having bus bar chamber with insulated electrolytic Aluminium bus bars TPN of capacity 200 Amps rating installed on DMC insulators with bus bar chamber. front opening type with proper ferrule & cable gland, internal wiring with PVC insulated multistranded copper conductor FRLS cable of adequate size but not less than 1.5 sqmm complete. All steel metal works including frame shall be with anticorrosive coating with seven tank process and finally epoxy polyester powder coating of Siemens grey RAL- 7035 shade. The scope of work also comprising of the following:-

BUS BAR CHAMBER:- (a) 200 Amps 3 Strips and Neutral Strip 100 Amps, Aluminium conductor, with color coded heat shrinkable sleave and shall be mounted on non hygroscopic, non combustible, track resistant, high strength DMC material, interconnection of all incomings & outgoings. (i) Red, Yellow, Green Phase indicating Lights LED type 220 V AC- 1 Set. (Set of three). INCOMING SUPPLY:- (i) MCCB 125 Amps 25 KA , 4 Pole with Adjustable thermal & Fixed magnetic setting release 415 Volts, 50Hz =01 No., Make of MCCB:-L&T/Siemens / Legrand/ Schneider OUTGOING SUPPLY:- (i) MCB SPN 40 Amps, 230 volts, 50Hz, rupturing capacity 10 KA = 5 Nos., Make of MCB:- L&T/ Siemens/ Legrand/ Schneider. (ii) Space for Fixing of 1 Phase, 2 Wire, Pre-paid Energy Meters- 04 Nos (iii) DMC Connector 2 way 100 A for outgoing submain supply - 5 Nos. Panel wiring for control circuit with copper flexible 1.5 Sq mm & power wiring minimum 4 Sqmm flexible.

Notes For Item No 202 Contd.....:- 1. The panel manufacturer should have following certification:- (i) CPRI certificate Degree of protection IP-54 (should have IEC: 61439-1-2 & IEC: 60529 tests) (ii) CPRI certificate short circuit with stand strength should be 50 KA RMS for 1 sec with initial peak of 105 KA. (iii) CPRI certificate rated current not less than 5000A 2. MCCB should be capable for on line setting of the current. 3. Drawing of panel board/meter box should be got approved from GE Clement Town before fabrication. 4. Panel board should be fully compartmentalized in accordance to form 4 b of IEC 61439-1-2.

M & L for sub main wiring with two run of 6 Sqmm (nominal cross sectional area ) of single core unsheathed PVC insulated cables FRLS-H cable 1100 Volts grade multi stranded copper conductor drawn through & including non metallic rigid PVC conduit of size 20 mm or higher dia with & including necessary conduit accessories concealed / surface only on roof & column) type including 6 Sqmm stranded copper conductor PVC insulated cable as earth wire connected to common earth dolly complete all as specified & directed. Note : Two runs of phsse and neutral wire and one run earth wire with PVC conduit measured as one length or one RM .

Material and labour for fixing or passing through pipe, laid in trenches, fixed on wall, LT panel board, XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area of size 35 sqmm 3.5 core with required aluminium cable lugs, lugs should properly crimmping with crimpping tools, heat shrink joints, Colour code heat shrink sleeves at both cable ends , cable gland for cable safety when passing through panel holes, including laying cable route indicators of suitable size RCC or steel type as per site requirement all as specified and directed. by Engr-in-charge. Note:(i) GI tubing required shall be measured and paid separately under relevant item of sch as supply only, (ii) Heat shrink sleeve of 25mm long on HS joint for colour indication shall deemed to be included on the quoted rate.

Excavation in trenches for taking out/laying of cable and pipe line not exceeding 1.5 mtr deep and not exceeding 1.5 mtr wide in soft/loose soil. complete all as specified and directed.

Returning, filling including spreading levelling watering and well ramming in layers not exceeding 25 cm thick in each layer in soft / lose soil.complete all as specified and directed.

Removing excavated material to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above starting point. complete all as specified and directed.

M & L for fine dry sand cushioning for underground cable by providing layers of sand 8 cm before laying and 15 cm deep after laying the cable including streching the cable (measurement to be taken after punning down consolidated thickness). complete all as specified and directed.

Supply and laying , un-reinforced precast concrete cable cover (ISI marked) ,class LV,Type I,flat,size 250mm X 150mm X 40mm with breaking load capacity 200 KG complete all as specified and directed.

Supplying, laying & jointing GI water tubing, 50 mm bore, light grade as in sleeving etc laid in trenches / pole post /under culvert/ under road etc. for cable protection complete all as specified and directed .

Supply and fixing ceiling fans complete with blades, down rods and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00, BEE Five star rated with brushless direct current motor (BLDC) including provision of cable flexible 3 core of suitable size wire from ceiling rose to Ceiling Fan complete all as specified and directed.

Taking down carefully by disconnecting and unscrewing from board / out lets boxes, electric meters of any locatios and refixing the same in new panel / existing panel complete all as specified and directed.

Material & labour for earthing complete with galvanised steel earth plate electrode 600 x 600 x 6 mm thick burried directly in ground. ( earth pit not less than 2.25 mtr depth below ground level at any type of strata ) with top edge of the earth plate not less than 1.5 mtr below normal ground level connected by GI strip 25 x 4 mm as earth lead by means of brass nuts and bolt,thimbles check nuts, washers including concrete chamber of PCC 1:3:6 type C-1 using 20mm graded stone aggregate with fair finish, internal surface of concrete chamber shall be given internal dia 300 mm x 300 mm, 15mm thick plaster in CM 1:4 funnel with wire mesh, RCC pit cover of 320 x 320 x 80 mm size (1:2:4) Type B1 using 20mm graded stone aggregate rainforced with XPM and charcoal, dust and common salt all as shown in electrical plate No 3 of MES SSR Part-1 (2009) and specified including and provision of GI wire upto 7.5 mtrs long with 15 mm dia light grade Gi pipe protection and watering pipe of GI 20 mm bore, medium grade, including all excavation and earth work and connecting the earthing strip to panel, including testing on completion complete all as specified and directed by Engr-in-charge. Note:- (i) RCC pit cover shall be precast of RCC (1:2:4) type B1, 80mm thick rainforced with XPM weighting not less than 4 kg / sqm in lieu of CI cover. (ii) Cost of additional GI wire more than 7.5 mtrs will be measured and paid seperately under relevant items.

Supply, installation and testing of electric chimney of size 90 cm with motion sensor, energy efficient, baffle filter, oil collector cup auto clean, led lemp 8 w and touch control max section 1350 cum/hr, filter less technology, motor power 145W, metallic blower including making suitable hole for exhaust pipe complete all as specified

Note : Tenderers may note that amount of credit Rs 8,16,291.00 will be deducted from the total amount arrived, at the time of Acceptance of contract.

GAYATRI CONSTRUCTION (BID ID -3149167)

PAWAN KUMAR (BID ID -3147309)

M/S SURAT SINGH AND SONS (BID ID -3149013)

V r traders (BID ID -3147300)

Ms dev associates (BID ID -3147361)

yash enterprises (BID ID -3146525)

CHITTER MAL & CO (BID ID -3148801)