Improvement of Sri SriMadhabdev Kalakshetra at Narayanpur, Dist Lakhimpur, Assam, (Phase-IV)

Amount

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Excavating, Supplying and filling of local earth(inculding Royality) by mechanical transport upto a lead of 5 km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:3:6 (1 Cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 20 mm nominal size)

Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III): 4 graded stone aggregate 12.5mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Centering and shuttering including strutting, propping etc. and removal of form forFoundations, footings, bases of columns, etc. for mass concrete

Centering and shuttering including strutting, propping etc. and removal of form forSuspended floors, roofs, landings, balconies and access platform

Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers

Centering and shuttering including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:Cement mortar 1:4 (1 cement : 4 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.Cement mortar 1:3 (1 cement : 3 coarse sand)

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels.Granite stone slab of colour black, Cherry/Ruby red (below 0.5sqm)

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately).Kiln seasoned and chemically treated hollock wood

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing M.S Grill Of required patteern in Frames ofg windows etc.. With MS Flat, Sqaure or Round Bars etcincludinf primering cot with approved stell primer all complet.Fixing to opening or wooden frame with rawl plug, Screws etc.

Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete :300x16 mm

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. 250x10 mm

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.Twin rubber stopper

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately).Two track two panels sliding window made of (small series) frame 52 x 44 mm &sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area of window upto 1.75 sqm)

Three track three panels sliding window made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm)

Providing and fixing zinc alloyed (white powder coated) touch lock for uPVC sliding window with necessary screws etc. complete.

Providing and fixing steel roller for uPVC sliding window with necessary screws etc. complete

Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete.125 mm

Structural steel work in single section, fixed with or without connecting plate, including cutting, hosting, fixing in position and applying a priming coat of approved steel primer all complete. (For pole of Post Top LED Lights)

Structural steel work in riveted, bolted or welded in built up sections, trusses and framed work, including cutting hosting and fixing in position and applying a priming coat of approved steel primer all complete (For pole of LED Street Lights)

Structural steel work riveted, bolted or welded in bulit up sections, trusses and framed work, including cutting, hosting, fixing in position and applhying a priming coat of approved steel primer all complete. (For GATE at Main Entry Point)

Dry brick on edge flooring in required pattern with bricks of class designation 7.5 on a bed of 12 mm mud mortar, including filling joints with Jamuna sand, with common burnt clay non modular bricks.

Cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement.18 mm thick

Providing and fixing 10 mm thick acid and/or alkali resistant tiles of approved make and colour using acid and/or alkali resisting mortar bedding, and joints filled with acid and/or alkali resisting cement as per IS : 4457, complete as per the direction of Engineer-in- Charge.In flooring on a bed of 10 mm thick mortar 1:4 (1 acid proof cement : 4 coarse sand) Acid and Alkali resistant tile

In dado/skirting on 12 mm thick mortar 1:4 (1 acid proofcement : 4 coarse sand) Acid and Alkali resistant tile

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.Glazed vitrified floor tiles polished finish of sizeSize of Tile 600x600 mm

Glazed Vetrified tiles Matt/Antiskid finish of Size of Tile 600 x 600 mm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).Size of Tile 600x600 mm

Providing and laying flamed finish Granite stone flooring in required designand patterns, in linear as well as curvilinear portions of the building allcomplete as per the architectural drawings with 18 mm thick stone slabover 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade includingrubbing, curing and polishing etc. all complete as specified and asdirected by the Engineer-in-Charge.Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement.18 mm thick

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) : 2011 (Board with BIS certification marks)

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :Ridges plain (500 - 600mm)

12 mm cement plaster of mix1:4 (1 cement: 4 coarse sand)

15 mm cement plaster on the rough side of single or half brick wall of mix :1:4 (1 cement: 4 coarse sand)

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Painting steel work with Delux Multi Surface Paint to give and even shade. Two or more coat applied @ 0.9Lts/10 sqm over and under coat of primer applied @ 0.8Lts / 10 sqm of approved brand and manufacturer.

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications :Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr /10 sqm

Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives.New work (Two or more coats applied @ 1.43 litre/ 10 sqm. Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm. (in Museum inside Walls/Displays)

Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture

Varnishing with varnish of approved brand and manufactureTwo or more coats glue sizing with spar varnish or an under coat of flatting varnish

Providing and fixing brass curtain rods of wall thickness 1.25 mm with two brass brackets fixed with brass screws and wooden plugs etc. wherever necessary complete. (to be installed only on windows)25mm diametre

Providing and fixing bright finished brass helical door spring (superiorquality).

Cutting holes of required size in brick masonry wall for fixing of exhaust fan including providing and fixing 300 mm dia PVC pipe conforming BIS-12818 and making good the same etc. complete as per direction of Engineer-in-charge. (For old existing walls)

Dismantling WC Pan of all sizes including disposal of dismantled materials all complete as per directions of Engineer in Charge

Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer 3 mm thick water proofing membrane, black finished reinforced with non-woven polyester matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 litre/sqm by the same membrane manufacture of density at 25°C, 0.87-0.89 kg/ litre and viscocity 70-160 cps. Over the primer coat the layer of membrane shall be laid using Butane Torch and sealing all joints etc, and preparing the surface complete. The vital physical and chemical parameters of the membrane shall be as under : Joint strength in longitudinal and transverse direction at 23°C as 650/ 450N/ 5cm. Tear strength in longitudinal and transverse direction as 300/ 250N. Softening point of membrane not less than 150°C. Cold flexibility shall be upto -2°C when tested in accordance with ASTM, D - 5147. The laying of membrane shall be got done through the authorised applicator of the manufacturer of membrane (over old RCC Surface)3mm thick

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per directionof Engineer - in - charge.Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.

Extra for cutting reinforcement bars manually/ by mechanical means in R.C.C. or R.B. work (Payment shall be made on the cross ectional area of R.C.C. or R.B. work) as per direction of Engineerin- charge.

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.In cement mortar

Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres leadOf area 3 sq. metres and below

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.For thickness of tiles 10 mm to 25 mm

Dismantling cement asbestos or other hard board ceiling or partition walls including stacking of serviceable materials and disposal of unserviceable materials within 50 metres lead.

Dismantling C.I. pipes including excavation and refilling trenches after taking out the pipes, manually/ by mechanical means breaking lead caulked joints, melting of lead and making into blocks including stacking of pipes & lead at site within 50 metre lead as per direction of Engineer-in-charge:Up to 150 mm diameter

Dismantling of flushing cistern of all types (C.I./PVC/Vitrious China) including stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead.

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer- in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. (For external conduiting work in Front Parking Area)External Work25 mm nominal outer dia Pipes

Float glass panes of nominal thickness 5 mm (weight not less than 12.50 kg/sqm)

Providing and fixing 12mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer in charge

Providing and laying four courses water proofing treatment with bitumen felt over roofs consisting of first and third courses of blown bitumen 85/25 or 90/15 conforming to IS : 702 applied hot @ 1.45 Kg per square metre of area for each course, second course of roofing felt type 3 grade-I (hessian based self finished bitumen felt) and fourth and final course of stone grit 6 mm and down size or pea sized gravel spread at 6 cubic decimeter per square metre, including preparation of surface but excluding grading complete withBitumen felt (hessian base) type 3 grade I conforming to IS : 1322

Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litres with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge.

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:-(a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :Kitchen sink without drain board610x510 mm bowl depth 200 mm

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.

Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge.15 mm nominal dia

Providing and fixing 100 mm sand cast Iron grating for gully trap.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete.

Providing and fixing soil, waste and vent pipes100 mm diaCentrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989

75 mm diaCentrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989

Providing and filling the joints with spun yarn, cement slurry and cement mortar 1:2 ( 1 cement : 2 fine sand) in S.C.I./ C.I. Pipes75 mm dia pipe

Providing and filling the joints with spun yarn, cement slurry and cement mortar 1:2 ( 1 cement : 2 fine sand) in S.C.I./ C.I. Pipes100 mm dia pipe

Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.ForFor 100 mm dia pipeSand cast iron S&S as per IS - 3989

Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.For 75 mm dia pipeSand cast iron S&S as per IS - 3989Sand cast iron S&S as per IS - 3989

Providing and fixing plain bend of required degree.For 100 mm dia pipeSand cast iron S&S as per IS - 3989

Providing and fixing plain bend of required degree.For 75 mm dia pipeSand cast iron S&S as per IS - 3989

Providing and fixing double equal junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete :100X100X100X100MMSand cast iron S&S as per IS - 3989

Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.100X100X100X100MMSand cast iron S&S as per IS - 3989

Providing and fixing door piece, insertion rubber washer 3mm thick, bolts & nuts completeFor 100 mm dia pipeSand cast iron S&S as per IS - 3989

Providing and fixing terminal guardFor 100 mm dia pipeSand cast iron S&S as per IS - 3989

Providing and fixing collarFor 100 mm dia pipeSand cast iron S&S as per IS - 3989

Providing and fixing M.S. stays and clamps for sand cast iron/centrifugally cast (spun) iron pipes of diameter100MM

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors :100mm inlet and 100mm outletSand cast iron S&S as per IS: 3989

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors :100mm inlet and 75mm outletSand cast iron S&S as per IS: 3989

Painting sand cast iron/ centrifugally cast (spun) iron soil, waste vent pipes and fittings with two coats of synthetic enamel paint of any colour such as chocolate grey, or buff etc. over a coat of primer (of approved quality) for new work.100MM dia pipe

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors 75MM dia pipe

Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour.Waste coupling 38 mm dia of 83 mm length and 77mm breadth, weighing not less than 60 gms

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour,weighing not less than 88 gms.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms

Constructing soak pit 1.20x1.20x1.20 m filled with brickbats including S.W. drain pipe 100 mm diameter and 1.20 m long complete as per standard design

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the walls etc.15 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the walls etc.20 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the walls etc.25 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.External Work 25 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.External Work 32 mm nominal outer dia Pipes

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :25 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :32 mm nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete.20mm nominal bore

Providing and fixing uplasticised PVC connection pipe with brass unions45cm length,15mm nominal bore

Providing and fixing CP brass shower rose with 15mm or 20mm inlet 150mm diametre

Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design.With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.15 mm nominal bore

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931,15mm nominal bore

Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.Group C

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.2 X 4 sq. mm + 1 X 4 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 6 sq. mm + 1 X 6 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 4 X 6 sq.mm + 2 X 6 sq.mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.4 X 10 sq.mm + 2 X 6 sq.mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 4 X 16 sq.mm + 2 X 6 sq.mm earth wire

Supplying and drawing following pair 0.5mm dia FRLS PVC insulated annealed copper conductor, unarmoured telephone cable in existing surface / recessed / PVC conduit as required 1 Pair

Supplying and drawing following pair 0.5mm dia FRLS PVC insulated annealed copper conductor, unarmoured telephone cable in existing surface / recessed / PVC conduit as required 2 Pair

Supplying and drawing following pair 0.5mm dia FRLS PVC insulated annealed copper conductor, unarmoured telephone cable in existing surface / recessed / PVC conduit as required 3 Pair

Supplying and drawing co-axil TV cable RG6 grade, 0.7mm solid copper conductor PE insulated, shelded with fine tinned copper braid and protected with PVC sheath in the existing surface or recesssed steel / PVC conduit as required

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface / recess including cutting the wall and making good the same in case of recessed conduit as required 20 mm

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface / recess including cutting the wall and making good the same in case of recessed conduit as required 25 mm

Supplying and fixing following modular switch / socket on existing modular plate & switch box including connections but excluding modular plate etc as required. 5/6 A Switch

Supplying and fixing following modular switch / socket on existing modular plate & switch box including connections but excluding modular plate etc as required. 2 way 5/6 A Switch

Supplying and fixing following modular switch / socket on existing modular plate & switch box including connections but excluding modular plate etc as required. 15/16 A Switch

Supplying and fixing following modular switch / socket on existing modular plate & switch box including connections but excluding modular plate etc as required. 3 pin 5/6A socket outlet

Supplying and fixing following modular switch / socket on existing modular plate & switch box including connections but excluding modular plate etc as required. 6 pin 15/16A socket outlet

Supplying and fixing following modular switch / socket on existing modular plate & switch box including connections but excluding modular plate etc as required. Telephone socket outlet

Supplying and fixing following modular switch / socket on existing modular plate & switch box including connections but excluding modular plate etc as required. TV antena socket outlet

Supplying and fixing following modular switch / socket on existing modular plate & switch box including connections but excluding modular plate etc as required. Bell Push

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections as required but excluding modular plate etc.

Supplying and fixing following size / modules, GI box along with modular base & cover plate for modular switches in recess etc. as required 1 or 2 Module

Supplying and fixing following size / modules, GI box along with modular base & cover plate for modular switches in recess etc. as required 8 Module

Supplying and fixing following size / modules, GI box along with modular base & cover plate for modular switches in recess etc. as required 12 Module

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

Supplying and fixing 3 pin 5A ceiling rose on existing junction box / wooden block including connections etc as required

Installation, testing and commissioning of wall bracket / ceiling fittings of all sizes and shapes containing upt two GLS/CFL / LED lamps per fitting, complete with all accessories including connection etc. as required.

Installation, testing and commissioning of pre wired, fluorescent fitting / complact fluroscent fittings of all types, complete with all accessories and tube / lamp etc directly on ceiling / wall including connections with 1.5 sq mm FRLS PVC insulated, copper conductor, single core cable and earthing etc as required.

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30cm) with 1.5 sq mm FRLS PVC insulated copper conductor single core cable etc including providing and fixing phenolic laminated sheet cover on the fan box etc as required

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing commisisioning etc as requireUpto 450mm sqeep

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface / recessed Steel / PVC Conduit as required. 1 run of cable

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface / recessed Steel / PVC Conduit as required. 2 run of cable

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface / recessed Steel / PVC Conduit as required. 3 run of cable

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required. Group C

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 2 nos of 3 pin 5/6 A modular socket outlet and 2 nos 5/6 A modular switch connections etc. as required (For light plugs to be used in non residential buildings)

Supplhying & fixing suitable size GI box with modular plate and cover in fron on surface or in recess including providing and fixing 25A modular socket outlet and 25A modular SP MCB "C" Curve including connections, painting etc as required.

Supplying and fixing PVC batten/ angle holder including connections etc. as required.

Supplying and fixing following way. Single pole and neutral, sheet steel, MCB distribution board, 240V, on surface / recess complete with tinned copper bus bar, nutral bus bar, earth bar, din bar, interconnections, powder coated including earthing etc. as required. 8 way, Double Door

Supplying and fixing following way. Single pole and neutral, sheet steel, MCB distribution board, 240V, on surface / recess complete with tinned copper bus bar, nutral bus bar, earth bar, din bar, interconnections, powder coated including earthing etc. as required 12 way. Double Door

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 4 way (4 + 12), Double door

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 6 way (4 + 18), Double door

Supplying and fixing following ways surface / recess mounting, vertical type 415V TPN MCB districution board of, sheet steel, dust protected duly powder painted inclusive of 200A tinned copper bus bar, common neutral link, earth bar din bar for mounting MCBs (but without MCBs and incomer) as required. (Note: Vertical type MCB TPDB is normally used where 3 phase outlet are required)6 way (4 + 18), Double door

Supplying and fixing following ways surface / recess mounting, vertical type 415V TPN MCB districution board of, sheet steel, dust protected duly powder painted inclusive of 200A tinned copper bus bar, common neutral link, earth bar din bar for mounting MCBs (but without MCBs and incomer) as required. (Note: Vertical type MCB TPDB is normally used where 3 phase outlet are required)8 way (4 + 24), Double door

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole and Neutral

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Triple pole and Neutral

Supplying and fixing single pole blanking plate in the existing MCB DB complete as required

Supplying and fixing Cable End Box (Loose Wire Box) suitable for the following Triple pole and Neutral sheet steel MCB DB 415 Volts on surface / recess complete with testing and commissioning etc as required. For 4 Way, Double Door TPN MCBDB

Supplying and fixing Cable End Box (Loose Wire Box) suitable for the following Triple pole and Neutral sheet steel MCB DB 415 Volts on surface / recess complete with testing and commissioning etc as required. For 6 way Double Door TPN MCBDB

Supplying and fixing Cable End Box (Loose Wire Box) suitable for the following Triple pole and Neutral sheet steel Vertical MCB DB 415 Volts on surface / recess complete with testing and commissioning etc as required.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required.

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut,bolt, spring, washer excavation and re-filling etc. as required.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV Grade of following size direct in ground including excavation, sand coushioning, protective covering and refilling the trench etc as required Upto 35 sqmm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV Grade of following size direct in ground including excavation, sand coushioning, protective covering and refilling the trench etc as required Above 35 sqmm to 95 sqmm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV Grade of following size in existing RCC / Hume / Metal pipe as required Upto 35 sqmm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV Grade of following size in existing RCC / Hume / Metal pipe as required Above 35 sqmm and upto 95 sqmm

Supplying and making end termination with brass compression gland and aluminium lugs for following sizes of PVC insulated PVC sheathed / SLPE aluminium conductor cable of 1.1 KV grade as required, 4 X 50 sqmm (35mm)

Supply Installation, Testing & Commissioning of modular type Variable Refrigerant Flow/Variable Refrigerant Volume air cooled Outdoor units suitable for cooling and heating, having all hermetically sealed inverter type Scroll Compressor(s), minimum two compressors for above 14 HP modules, microprocessor based Controller, top discharge type condensing unit(s), with R 410 A Refrigerant, vibration isolators, with suitable foundation etc. complete as required. The unit shall deliver the rated capacity at AHRI Conditions and work even at 50°C ambient temperature without tripping. The unit shall be suitable to work on 400V +/- 10%, 3 Phase, 50Hz AC power supply. The unit shall be filled with first charge of the refrigerant and ready for use as required. The COP at AHRI conditions shall not be less than 3.1 and IEER not less than 6.5 .

Supply, installation, testing and commissioning of following minimum capacity 4-way flow VRV/VRF Cassette Type Indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX Copper coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration isolation, cord less remote control etc., suitable for operation on single phase 230 V ± 10%, 50Hz AC supply, complete, as required. The unit shall have automatic force shut down provision in case of fire on receiving signal from BMS System. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature. 1.2 TR

Supply, installation, testing and commissioning of following minimum capacity 4-way flow VRV/VRF Cassette Type Indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX Copper coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration isolation, cord less remote control etc., suitable for operation on single phase 230 V ± 10%, 50Hz AC supply, complete, as required. The unit shall have automatic force shut down provision in case of fire on receiving signal from BMS System. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature. 1.6 TR

Supply, installation, testing and commissioning of following minimum capacity 4-way flow VRV/VRF Cassette Type Indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX Copper coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration isolation, cord less remote control etc., suitable for operation on single phase 230 V ± 10%, 50Hz AC supply, complete, as required. The unit shall have automatic force shut down provision in case of fire on receiving signal from BMS System. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature. 2.0 TR

Supply, installation, testing and commissioning of following minimum capacity 4-way flow VRV/VRF Cassette Type Indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX Copper coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration isolation, cord less remote control etc., suitable for operation on single phase 230 V ± 10%, 50Hz AC supply, complete, as required. The unit shall have automatic force shut down provision in case of fire on receiving signal from BMS System. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature. 2.4 TR

Supply, installation, testing and commissioning of following minimum capacity 4-way flow VRV/VRF Cassette Type Indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX Copper coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration isolation, cord less remote control etc., suitable for operation on single phase 230 V ± 10%, 50Hz AC supply, complete, as required. The unit shall have automatic force shut down provision in case of fire on receiving signal from BMS System. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature. 2.8 TR

Supply, installation, testing and commissioning of following minimum capacity 4-way flow VRV/VRF Cassette Type Indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX Copper coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration isolation, cord less remote control etc., suitable for operation on single phase 230 V ± 10%, 50Hz AC supply, complete, as required. The unit shall have automatic force shut down provision in case of fire on receiving signal from BMS System. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature. 3.2 TR

Supply, installation, testing and commissioning of following minimum capacity 4-way flow VRV/VRF Cassette Type Indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX Copper coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration isolation, cord less remote control etc., suitable for operation on single phase 230 V ± 10%, 50Hz AC supply, complete, as required. The unit shall have automatic force shut down provision in case of fire on receiving signal from BMS System. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature. 4 TR

Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessories as per specifications etc. as required : 6.4 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation

Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessories as per specifications etc. as required :9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation

Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessories as per specifications etc. as required : 12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation

Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessories as per specifications etc. as required :15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation

Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessories as per specifications etc. as required : 19 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation

Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessories as per specifications etc. as required : 22.2 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation

Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessories as per specifications etc. as required : 28.58 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation

Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessories as per specifications etc. as required : 34.9 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm with 19 mm thick insulation

Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessories as per specifications etc. as required : 41.27 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm with 19 mm thick insulation

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal Work: Exposed 25 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal Work 32 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal Work 40 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External Work 25 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External Work 32 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External Work 40 mm nominal outer dia Pipes

Rewiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm already available FRLS PVC insulated copper conductor single core cable etc. as required. Group C

Rewiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm already existing FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Rewiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

Rewiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

Rewiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.2 X 4 sq. mm + 1 X 4 sq. mm earth wire

Rewiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.2 X 6 sq. mm + 1 X 6 sq. mm earth wire

Rewiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.Group C

Refixing already removed following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panels, making connections etc as required100A, 30KA FPMCCB

Refixing already removed, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

Refixing already removed surface / recess mounting, vertical type 415V TPN MCB districution board of, sheet steel, dust protected duly powder painted inclusive of 200A tinned copper bus bar, common neutral link, earth bar din bar for mounting MCBs (but without MCBs and incomer) as required. (Note: Vertical type MCB TPDB is normally used where 3 phase outlet are required)

Refitting already removed 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying of 250 mm sweep Domestic Exjhaust fan

Supplying and fitting of 10W Decorative Slim Linear LED Batten Luminaire (6500K) of length 600mm complete with all accessories to the full satisfaction of the Department

Supplying and fitting of 12Watt LED BULB with battery and 2 years warrantee in the existing batten holder/angle holder/decorative bracket/bulk head fitting/ pendent holder etc. as specified and directed by the deptt.

Supplying and fitting of 10-20 Watt Round LED Panel Conceal Light complete with all accessories such as starter/adapter etc.

Supplying of 36W 2X2 concealed Panel Light complete with all accessories such as starter/adapter etc..

Supplying installing testing and commssioning of 9W Track Light complete with all accessories such as starter/adapter etc..

Supplying installing, testing and commissioning of 12W Track Light complete with all accessories such as starter/adapter etc..

Supplying installing, testing and commissioning of 12W Warm White Aluminium Circular LED surface ceiling Light (12W SPOT LIGHT) complete with all accessories such as starter/adapter etc..

Supplying installing, testing and commissioning of 4W Warm White PVC Square LED surface ceiling Light (LED Wall Surface Spot Light) complete with all accessories such as starter/adapter etc.. to the full satisfaction of the Department

Supplying installing, testing and commissioning of Mild Steel Wall Lamp;, 18W complete with all accessories such as starter/adapter etc..

Supplying, installing, testing and commissioning of 60W LED Street Light of IP 66 rating complete including all accessories to the full satisfaction of the Department (Ticketing area and Queing area) (Pole to be measured and paid saparately)

Supplying, installing testing and commissioning of Powder coated die cast aluminium alloy with UV stabilized clear one piece diffuser IP66 rated ED post top lantern of 40W including all accessories, to the full satisfaction of the Department. (Pole to be measured and paid saparately)

Supplying and fixing, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40A FP MCB

Supplying and fixing, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63A FP MCB

Supply and Installation of 4K HD Smart LED Samsung TV 80 cm (32 inches) in position as per design to the complete satisfaction of the Department

Supply and Installation of 4K Ultra HD Smart LED Google TV 139 cm (55 inch) in position as per design to the complete satisfaction of the Department

Supplying installing testing and commissioning of Viewsonic 4K Interactive Panel (4GB RAM, 32 GB Storage, Android 11 (Model-IFP6550-5) 55 Inch

Supplying and Installing testing and commissioning of Information Kiosks of latest generation Intel Core i5 (3.1GH) and 21.5 inch interractive screen including MS Powder Coated stand of suitable design, complete with all required accessories to the full satisfaction of the department

Supplying of Portable Dehumidifier having capacity of 60/Day with contineous drainge and water tank, Single Phase having power consumption of not more than 1000W, Capable of working at temperatures of 45 degrees and having humidity maintaining capaticy of 10% to90% and having noise level below 55DB, having refregerent R410A with auto defrost to the full satisfaction of the Department.

Supplhying and p roviding usha 1000 Watt Radiant heater (GEM) to the full satisfaction of the Department and Museum Curator

Supplying and commissioning Black & Decker Wet and Dry Duty Cleaning Industrial Vacuum Cleaner 60 milliba

Supplying 32GB Pendrive

Supplying, installing, testing and commissioning of 2MP IR Dome Camera and integrating them with the existing CCTV network complete in all respects including all accessories to the full satisfaction of the Department

Supplying, installing, testing and commissioning of 24 inch LCD Screen and integrating them with the existing CCTV network complete in all respects including all accessories to the full satisfaction of the Department

Supplying installing testing and commissioning of 6U Portable Racks Networking/Server Rack including all accessories to the full satisfaction of the Department

Supplhying installing testinng and commissioninng of 18U Portable Racks Networking/Server Rack including all accessories to the full satisfaction of the Department

Supplying, installing, testing and commissioning Fast Ethernet PoE Switch with 2 Gigabit Uplink, 8 10/100Mbps PoE RJ45 port (port 1~port 8) to the full satisfaction of the Department

Supplying, installing, testing and commissioning of 6 Core Single Mode Fibre Optic cable for CCTV with required end points to the full satisfaction of the Department

Supplying, installing, testing and commissioning 32 Channels NVR with 4K (3840 × 2160) and integrating it to the existing system complete with all accessories like connecting wires etc. to the full satisfaction of the Department.

Supplying, installing, testing and commissioning 64 Channels NVR with 4K (3840 × 2160) and integrating it to the existing system complete with all accessories like connecting wires etc. to the full satisfaction of the Department.

Supplying, installing testing and commissioning of 8TB Windows Surveillance Hard Disk and integrating it to the existing CCTV Network complete in all respects to the full satisfaction of the Department

Supplying and Installation of RJ45 female switch in existing MS Boxes and existing Moudlar Cover plates to the full satisfaction of the Department

Supplying, installing, testing and commissioning of 60W LED Street Light of IP 66 rating complete including all accessories to the full satisfaction of the Department (Ticketing area and Queing area) (Pole to be measured and paid saparately)

Supplying, installing testing and commissioning of Powder coated die cast aluminium alloy with UV stabilized clear one piece diffuser IP66 rated ED post top lantern of 40W including all accessories, to the full satisfaction of the Department. (Pole to be measured and paid saparately)

Supplying installing testing and commissioning of 1KVA Online UPS with 2 nos SMF 12V / 9AH X 2 Nos. (In-Built Batteries) to the full satisfaction of the Department

Supplying and Installing 3KVA 48V DC Inverted of approved brand complete to the full satisfaction of the Department

Supplhying and Installing of 12V 200 Ah 48VDC for 4 hrs. Battery backup of approved brand to the full satisfaction of the Department

Supplying, installing, testing and commissioning of 30KVA Diesel Generator, Water Cooled with AMF Panel complete with all accessories to the complet satisfaction of the Department

Supplying, installing, testing and commissioning of 125KVA Diesel Generator, Water Cooled with AMF Panel complete with all accessories to the complet satisfaction of the Department

Providing and fixing stored pressure ABC Fire Extinguisher consisting of welded M.S. cylinderical body, squeeze lever discharge valve 30 cms long high pressure discharge hose, discharge nozzle, suspension braket, ISI marked as per IS:13849 finished externally with red enamel paint and fixed to wall with brackets complete with internal charges. 4KG

Providing and fixing Carbon-di-oxide fire extinguishers consisting of welded M.S cylinderical body,squeeze lever discharge valve fitted with internal dischargetube,30cms long high pressure discharge hose, discharge nozzle, suspension bracket, confirming to IS : 2878 finished externally with red enamel paint and fixed to wall with brackets with rawl plug/dash fasteners complete with internal charge.4.5KG

Removing and refitting of already fitted 1.5T Split AC including stebelizer complete with all accessories and filling of additional gas etc complete to the full satisfaction of the Department

Removing and refitting of already fitted Geysers complete with all accessories complete to the full satisfaction of the Department

Supply of following armoured U.G. cable PVC/XLPE insulated and PVC sheathed 1.1 KV G Solid Aluminium conductor up to 10 sq mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, Armour (Aluminium for single core up to 70 sq mm balance Aluminium strip, Galvanised for cables up to 2x10 sq mm.3x10 sq mm,4x6 sq mm balance all galvanised steel strip) , extruded PVC Type ST2 sheathed, 650/1100V grade as per IS 7908(Part 1) 1988 armoured U.G. cable (Nicco/ Havells/ RPG/CCI/Polycab/Gloster/ Finolex make) . 3 Core 1.5mm (Copper)

Supply of following armoured U.G. cable PVC/XLPE insulated and PVC sheathed 1.1 KV G Solid Aluminium conductor up to 10 sq mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, Armour (Aluminium for single core up to 70 sq mm balance Aluminium strip, Galvanised for cables up to 2x10 sq mm.3x10 sq mm,4x6 sq mm balance all galvanised steel strip) , extruded PVC Type ST2 sheathed, 650/1100V grade as per IS 7908(Part 1) 1988 armoured U.G. cable (Nicco/ Havells/ RPG/CCI/Polycab/Gloster/ Finolex make) . 2 Core 6 sqmm

Supply of following armoured U.G. cable PVC/XLPE insulated and PVC sheathed 1.1 KV G Solid Aluminium conductor up to 10 sq mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, Armour (Aluminium for single core up to 70 sq mm balance Aluminium strip, Galvanised for cables up to 2x10 sq mm.3x10 sq mm,4x6 sq mm balance all galvanised steel strip) , extruded PVC Type ST2 sheathed, 650/1100V grade as per IS 7908(Part 1) 1988 armoured U.G. cable (Nicco/ Havells/ RPG/CCI/Polycab/Gloster/ Finolex make) . 4 Core 50 sqmm

Supply of following armoured U.G. cable PVC/XLPE insulated and PVC sheathed 1.1 KV G Solid Aluminium conductor up to 10 sq mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, Armour (Aluminium for single core up to 70 sq mm balance Aluminium strip, Galvanised for cables up to 2x10 sq mm.3x10 sq mm,4x6 sq mm balance all galvanised steel strip) , extruded PVC Type ST2 sheathed, 650/1100V grade as per IS 7908(Part 1) 1988 armoured U.G. cable (Nicco/ Havells/ RPG/CCI/Polycab/Gloster/ Finolex make) . 3.5 Core 95 sqmm

Supplying Installing Testing and Commsioning of HDPE Pipe to the full satisfaction of the Department

Supplying and fitting of Track for Track Light of 1m length complete with all accessories such as starter/adapter etc.. (Havells or equivalent)

Supplying and fitting of Track for Track Light of 2m length complete with all accessories such as starter/adapter etc.. (Havells or equivalent)

Supplying and fitting 100A Automatic Transfer Switch with UVT and Over Volatage protection, (AC-31A,50 HZ,415V) complete including all accessories as required, to the full satisfaction of the Department

Supplying Installing Testing and Commsioning of HDPE Pipe to the full satisfaction of the Department

Installing, testing and commissioning of professional museum quality 1.5 W SPOT LIGHT to the full satisfaction of the Curator and the Department

Installing, testing and commissioning of professional museum quality 3W SPOT LIGHT to the full satisfaction of the Curator and the Department

Installing, testing and commissioning of professional museum quality 5W SPOT LIGHT to the full satisfaction of the Curator and the Department

Installing, testing and commissioning of professional museum quality TRACK PATTY CORNER to the full satisfaction of the Curator and the Department

Installing, testing and commissioning of professional museum quality TRACK PATTY REGULAR to the full satisfaction of the Curator and the Department

Installing, testing and commissioning of professional museum quality TRACK DRIVER to the full satisfaction of the Curator and the Department

Installing, testing and commissioning of professional museum quality TRACK CONNECTOR to the full satisfaction of the Curator and the Department

Supplying and Installation of Curtains with Eyelet Rings complet with stitching for standard width of 1200mm/1500mm to the full satisfaction of the Department

Supplying and Installing 300KG Capacity MS Black Painted Trolley with wheels for Inverter and Battery

Fabrication, and Installation of the tensile fabric structure including Design considering appropriate wind load along with supply and installation of the anchors, base plates , supporting structure of suitable sections, and placing in position MS Built-up section/Tubular Structure ( MS built-up section :-Rolled section & plates confirming to IS 2062 Grade Yst 310,Tubular Structure:- made from Steel hollow sections, ISI marked from / TATA/JINDAL/NEZONE, conforming to IS 1161/4923, Grade Yst 310 & +, thickness as required) and fabric membrane of SERGE FERRARI of minimum 780GSM, including preparation of drawings and including all accessories to the full satisfaction of the Department

External Cladding done with 2.5mm thick, exterior grade, environment friendly, lightweight and flexible material of MCM Phomi make of approved design and shade complete with all accessories and installation for all floorsDesign: A Series Brick

Providing and fixing C.P. Two Way Bib Cock (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge (Jaquar Aria or equivalent) ARI-CHR-39041

Providing and fixing C.P. brass angle valve of 15mm dia of approved quality conforming to IS:8931 (Jaquar Aria or equivalent) ARI-CHR-39053

Providing and fixing C.P. Health Foecet with 1000mm long pipe of 15mm dia of approved quality conforming to IS:8931 (Jaquar or equivalent)

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931 (Jaquar Florentine or Equivalent)

Providing and fixing C.P. Pillar Cock Tall Boy of standard design and of approved make conforming to IS:8931 (Jaquar Aria or Equivalent)

Providing and fixing C.P. SINGLE LEVER EXPOSED PARTS KIT OF HI-FLO of standard design and of Jaquar ARI-CHR-39079NK make conforming to IS:8931 (Jaquar Aria or Equivalent) + Spout

Providing and fixing CONCEALED BODY FOR SINGLE LEVER HIGH FLO DIVERTER of standard design and of Jaquar ALD-CHR-079N make conforming to IS:8931 (Jaquar Aria or Equivalent)

Provigind and fixing SHOWER ARM DIA. 20MM & 300MM LONG ROUND SHAPE WITH 90° BEND FOR WALL MOUNTED SHOWERS WITH FLANGE STAINLESS STEEL if Jaquar SHACHR- 479L300S or equivalent complete in all respects to the satisfaction of the department

Provigind and fixing OVERHEAD SHOWER 100MM DIA ROUND SHAPE SINGLE FLOW (FACE PLATE STAINLESS STEEL & ABS BODY IN CHROME FINISH) WITH RUBIT CLEANING SYSTEM if Jaquar OHS-CHR-1661 or equivalent complete in all respects to the satisfaction of the department

Providing and fixingTABLE TOP BASIN (JAQUAR ARS-WHT-39901), including painting of fittings and brackets, cutting and making good the walls wherever require:

Providing and fixing WALL HUNG WC WITH UF SOFT CLOSE (JAQUAR ARIA - ARS-WHT-39951UFSM water closet including concelaed cistern, front plate, seat cover, nuts, bolts and gasket etc complete in all respect to the satisfaction of the Department. (Jaquar Aria - )

Partitioning for Admin Building: Making, supplying and fixing in position, ply partitioning: Frame made out of 2 nos of 19mm BWP Block Board of approved quality of width 75mm placed at intervals of 600 c/c bothways, fixed with 9mm BWP Grade Ply on both sides, finished with 1.0 mm laminate of approved make and brand complete with all fixing accessories as per design and to the full satisfaction of the Department and Fixing of Doors as and where required. Payment of Doors to be done separately.

Panelling of Admin Building: Making, supplying and fixing in position, ply partitioning: Frame made out of 1 nos of 19mm BWP Block Board of approved quality of width 50mm placed at intervals of 600 c/c bothways, fixed with 9mm BWP Grade Ply on top, finished with 1.0 mm laminate of approved make and brand complete with all fixing accessories as per design and to the full satisfaction of the Department.

Table 1200X600X750: Making, supplying and placing in position Table of size 1200X600X750 made out of 19mm Water Proof Block Board of approved quality finished in the inside with 0.8mm White or Cream coloured Laminate and Finished on the outside with 1.0mm Laminate of Matt Wood Grain Finish of approved quality and shade. The table has to have a 300 wide drawer and cupboard unit having two drawer units of 150 with appropriate channels and the remaining as one cupboard. The table also needs to have a key board tray of size 450X300 on appropriate channels complete in all respects with auto closing hinges for cupboard unit and any other accessories, compete to the full satisfaction of the Department

Table 1350X600X750: Making, supplying and placing in position Table of size 1350X600X750 made out of 19mm Water Proof Block Board of approved quality finished in the inside with 0.8mm White or Cream coloured Laminate and Finished on the outside with 1.0mm Laminate of Matt Wood Grain Finish of approved quality and shade. The table has to have a 400 wide drawer and cupboard unit having two drawer units of 150 with appropriate channels and the remaining as one cupboard. The table also needs to have a key board tray of size 450X300 on appropriate channels complete in all respects with auto closing hinges for cupboard unit and any other accessories, compete to the full satisfaction of the Department

Table 1500X750X750: Making, supplying and placing in position Table of size 1500X750X750 made out of 19mm Water Proof Block Board of approved quality finished in the inside with 0.8mm White or Cream coloured Laminate and Finished on the outside with 1.0mm Laminate of Matt Wood Grain Finish of approved quality and shade. The table has to have a 400 wide drawer and cupboard unit having two drawer units of 150 with appropriate channels and the remaining as one cupboard. The table also needs to have a key board tray of size 450X300 on appropriate channels complete in all respects with auto closing hinges for cupboard unit and any other accessories, compete to the full satisfaction of the Department

Table 2400X1200X750: Making, supplying and placing in position Table of size 2400X1200X750 made out of 19mm Water Proof Block Board of approved quality finished in the inside with 0.8mm White or Cream coloured Laminate and Finished on the outside with 1.0mm Laminate of Matt Wood Grain Finish of approved quality and shade. The table has to have a 400 wide drawer and cupboard unit having two drawer units of 150 with appropriate channels and the remaining as one cupboard. The table also needs to have a key board tray of size 450X300 on appropriate channels complete in all respects with auto closing hinges for cupboard unit and any other accessories, compete to the full satisfaction of the Department

Table 2400X1200X750: Making, supplying and placing in position Table of size 2100X900 made out of 19mm Water Proof Block Board of approved quality finished in the inside with 0.8mm White or Cream coloured Laminate and Finished on the outside with 1.0mm Laminate of Matt Wood Grain Finish of approved quality and shade. The table has to have a 450 wide drawer and cupboard unit having two drawer units of 150 with appropriate channels and the remaining as one cupboard. The table also needs to have a key board tray of size 450X300 on appropriate channels complete in all respects with auto closing hinges for cupboard unit and any other accessories, compete to the full satisfaction of the Department

Side Table 1000X450X650: Making, supplying and placing in position Side Table of size 1000X450X650 made out of 19mm Water Proof Block Board of approved quality finished in the inside with 0.8mm White or Cream coloured Laminate and Finished on the outside with 1.0mm Laminate of Matt Wood Grain Finish of approved quality and shade.The Table will have a 250 wide CPU unit and the rest of the Side Table will have cupboard units with adequate vertical and horizontal divisions suitable for storage of Office Files etc. complete in all respects and to the satisfaction of the Department

Back Storage Unit:450 wide and 650 height: Making, supplying and placing in position Back Storage Unit of various lengths, of wide 450 and height 650 made out of 19mm Water Proof Block Board of approved quality finished in the inside with 0.8mm White or Cream coloured Laminate and Finished on the outside with 1.0mm Laminate of Matt Wood Grain Finish of approved quality and shade.The Table will have a 250 wide CPU unit and the rest of the Side Table will have cupboard units with adequate vertical and horizontal divisions suitable for storage of Office Files etc. complete in all respects and to the satisfaction of the Department

Back Storage Unit:450 wide and 2050 height: Making, supplying and placing in position Back Storage Unit of various lengths, of wide 450 and height 2050 made out of 19mm Water Proof Block Board of approved quality finished in the inside with 0.8mm White or Cream coloured Laminate and Finished on the outside with 1.0mm Laminate of Matt Wood Grain Finish of approved quality and shade.The Table will have a 250 wide CPU unit and the rest of the Side Table will have cupboard units with adequate vertical and horizontal divisions suitable for storage of Office Files etc. complete in all respects and to the satisfaction of the Department

Reception Table 3600X600X750: Making, supplying and placing in position Reception Table of size 3600X600X750 made out of 19mm Water Proof Block Board of approved quality finished in the inside with 0.8mm White or Cream coloured Laminate and Finished on the outside with 1.0mm Laminate of Matt Wood Grain Finish of approved quality and shade. The table has to have 2 nos of 300 wide drawer and cupboard unit having two drawer units of 150 with appropriate channels and the remaining as one cupboard. The table also needs to have a key board tray of size 450X300 on appropriate channels complete in all respects with auto closing hinges for cupboard unit and any other accessories, compete to the full satisfaction of the Department

Sofa Side Table: Making and providing Sofa Side Table of size 450X450 for Guest Rooms made out 19mm BWP Grade Block Board finished with 1.0mm laminate on all visible surfaces complete with all accessories as per design to the complete satisfaction of the Department

PANELLING of MUSEUM AND PANDULIPI- Supplying, making and fixing in position PANELLING as per design made out of 12mm BWP Grade Plyboard, finished with wall paper of desired shade over frame made out of 19mm block bload 150mm wide, members placed at 600 c/c bothsides complete in all respects with all accessories, fittings and fixtures to the full satisfaction of the Department.

DISPLAY 1- GF HALL NO 1: SATRA WAY OF LIFE (Wall Units): Supplying, making and fixing in position Display Unit Type 1 (3000 height, 2400 wide and 900 depth), as per design made out of 19mm BWP Grade Block Board, finished with desired finish on the inside and outside and enclosed with toughened clear glass front of 8mm thickness with openable parts as per design complete in all respects with all accessories, fittings and fixtures to the full satisfaction of the Department. (Inside and Outside finish to be measured and paid separately):

DISPLAY 3- GF HALL NO 2: MASK TRADITION OF ASSAM (Wall Units): Supplying, making and fixing in position Display Unit Type 3 (3000 height, 3300 wide and 920 depth), as per design made out of 19mm BWP Grade Block Board, finished finished with desired finish on the inside and outside andenclosed with toughened glass front of 8mm thickness with openable parts as per design complete in all respects with all accessories, fittings and fixtures to the full satisfaction of the Department. (Inside and outside finish to be measured and paid separately)

DISPLAY 4- GF HALL NO 2: MASK TRADITION OF ASSAM (Wall Units): Supplying, making and fixing in position Display Unit Type 4 (3000 height, 2400 wide and 620 depth), as per design made out of 19mm BWP Grade Block Board, finished finished with desired finish on the inside and outside and enclosed with toughened glass front of 8mm thickness with openable parts as per design complete in all respects with all accessories, fittings and fixtures to the full satisfaction of the Department. (Inside and outside finish to be measured and paid separately)

DISPLAY 5- GF HALL NO 3: ETHENIC ASSAM (All Units): Supplying, making and fixing in position Display Unit Type 5 (3000 height, 3000 wide and 920 depth), as per design made out of 19mm BWP Grade Block Board, finished with 1mm Laminate of desired make and shade on the outside and desired finishin the inside and enclosed with clear toughened glass front of 8mm thickness with openable parts as per design complete in all respects with all accessories, fittings and fixtures to the full satisfaction of the Department. (Inside finish to be measured and paid separately)

DISPLAY 6- FF HALL NO 4 (FULL SIZE SCULPTURE) (Wall Side) : Supplying, making and fixing in position Display Unit Type 6 (3300 height, 8800 wide and 1800 depth), having 3 nos of display units as per design made out of 19mm BWP Grade Block Board, finished finished with desired finish on the inside and outside and and clear toughened glass front of 8mm thickness on the front with openable doors at the sides complete in all respects with all accessories, fittings and fixtures to the full satisfaction of the Department. (Outside and inside finish to be measured and paid separately)

DISPLAY 7- FF HALL NO 4 (COSTUME DISPLAY) (Central Display) : Supplying, making and fixing in position Display Unit Type 7 (1000 height, 6000 wide and 600 depth), as per design made out of 19mm BWP Grade Block Board, finished finished with desired finish on the inside and outside, and in shape and design as per drawing, with divisions at 1000mm apart, for display of costumes and dresses in a slant manner, and having openable with 6mm clear heat strengthened glass on top, with openable storage space at the bottom, to the full satisfaction of the Department. (Inside and outside finish to be measured and paid separately)

DISPLAY 8- FF HALL NO 5 (GIFTS RECEIVED BY CHIEF MINISTER (Wall Side) : Supplying, making and fixing in position Display Unit Type 1 (3000 height, 2200 wide and 950 depth, with boxes for display of items), as per design made out of 19mm BWP Grade Block Board, finished with 1mm Laminate of desired make and shade on the outside and desired finish in the inside and enclosed with clear toughened glass front of 8mm thickness with openable parts as per design complete in all respects with all accessories, fittings and fixtures to the full satisfaction of the Department. (Inside finish to be measured and paid separately).

DISPLAY 9- FF HALL NO 5: GIFTS RECEIVED BY CHIEF MINISTER (Centre): Supplying, making and fixing in position Display Unit Type 9 (3000 height, 6400 wide and 950 depth, with boxes for display of items), as per design made out of 19mm BWP Grade Block Board, finished finished with desired finish on the inside and outside and and enclosed with clear toughened glass front of 8mm thickness with openable parts as per design complete in all respects with all accessories, fittings and fixtures to the full satisfaction of the Department. (Inside and outside finish to me measured and paid separately)

DISPLAY 10- FF HALL NO 6: LOCAL MATERIALS OF ASSAM (Wall Units):Supplying, making and fixing in position Display Unit Type 10 (2550 height, 2.85 wide and 1150 depth), as per design made out of 19mm BWP Grade Block Board, finished finished with desired finish on the inside and outside and and enclosed with clear toughened glass front of 8mm thickness with openable parts as per design complete in all respects with all accessories, fittings and fixtures to the full satisfaction of the Department. (Inside and outside finish to me measured and paid separately)

DISPLAY 11- FF HALL NO 6: LOCAL MATERIALS OF ASSAM(Central Units): Supplying, making and fixing in position Display Unit Type 11 (2550 height, 2850 wide and 1150 depth), as per design made out of 19mm BWP Grade Block Board, finished finished with desired finish on the inside and outside and and enclosed with clear toughened glass front of 8mm thickness with openable parts as per design complete in all respects with all accessories, fittings and fixtures to the full satisfaction of the Department. (Inside and outside finish to me measured and paid separately)

MUSEUM PARTITIONING: HALL 7 and Library: Supplying, making and fixing in position ART GALLERY PARTITIONS in Gallery 7 (Art Gallery) as per design made out of 12mm BWP Grade Plyboard, finished with desired finish over frame made out of 19mm block board 75mm wide, members placed at 600 c/c bothsides complete in all respects with all accessories, fittings and fixtures to the full satisfaction of the Department. (Final finish to be measured and paid separately)

DISPLAY 12-: (SHOWCASE): Supplying, making and fixing in position Display Unit Type 12 (2100 height,1200 wide and 1200 depth), as per design, top and bottom 200mm made out of 19mm BWP Grade Block Board, finished with 1mm Laminate of desired make and shade on the outside and desired finish in the inside and fixed with 9mm one side openable toughened glass as per design complete in all respects with all accessories, fittings and fixtures to the full satisfaction of the Department. The unit is to be made complete with a inside pedestal made of 19mm BWP Grade Block Board of size 900X900X900finished with desired finish with provision of 4 nos of lights points in the inside. (Inside and outside finish to be measured and paid separately)

DISPLAY 13-: (SHOWCASE): Supplying, making and fixing in position Display Unit Type 13 (2100 height,1500 wide and 1500 depth), as per design, with bottom part as Pedestal of 1500X1500X1200 made of 19 mm BWP Block Board of desired quality and top portion of 8mm toughened glass of 1500X1500X900 with facility for opening one side, finished with desired finish complete in all respects with all accessories, to the full satisfaction of the Department Supplying, making and fixing in position Display Unit Type 13 (2100 height,1500 wide and 1500 depth), as per design, with bottom part as Pedestal of 1500X1500X1200 made of 19 mm BWP Block Board of desired quality and top portion of 8mm toughened glass of 1500X1500X900 with facility for opening one side, finished with desired finish complete in all respects with all accessories, to the full satisfaction of the Department (Inside and Outside Finish to be measured and paid separately)

DISPLAY 14-: (SHOWCASE): Supplying, making and fixing in position Display Unit Type 14(2700 height, 2100 wide and 900 depth), as per design, with bottom part as Pedestal of 2100X900X900 made of 19 mm BWP Block Board of desired quality and top portion of 8mm toughened glass of 2100X900X600 with facility for opening one side, finished with desired finish complete in all respects with all accessories, to the full satisfaction of the Department. This is to be topped with 1200X1200X1200 wall mounted 8mm toughened glass cabinet as per directions of the Curator (Inside and Outside Finish to be measured and paid separately)

DISPLAY 15-: (SHOWCASE): Supplying, making and fixing in position Display Unit Type 15 (1200 height, 900 wide and 1200 depth), as per design, with bottom part as Pedestal of 1200X900X600 made of 19 mm BWP Block Board of desired quality and top portion of 8mm toughened glass of 1200X900X600 with facility for opening one side, finished with desired finish complete in all respects with all accessories, to the full satisfaction of the Curator. (Inside and outside finish to be measured and paid separately)

DISPLAY 16- : (CIRCULAR PLATFORM): Supplying, making and fixing in position Circular Display Unit Type 16 (300 height and 2100 dia), as per design, made of 19mm dia Block Board frame finished with 6mm flexi ply and wrapped with carpet / fabric of desired quality to the full satisfaction of the Curator. (Carpet or fabric to be measured and paid separately)

DISPLAY 17- : (PLATFORM): Supplying, making and fixing in position Display Unit Type 17 (300 height and 2100 dia), as per design, made of 19mm dia Block Board frame finished with 6mm flexi ply and wrapped with carpet / fabric of desired quality to the full satisfaction of the Curator. (Carpet or Fabric to be measured and paid separately)

DISPLAY 18- : (PLATFORM): Supplying, making and fixing in position Display Unit Type 18 (600 height 3000X1200), as per design, made of 19mm dia Block Board frame finished with 6mm flexi ply and wrapped with carpet / fabric of desired quality to the full satisfaction of the Curator. (Carpet or Fabric to be measured and paid separately)

FABRIC WRAPPED PANELLING- Supplying, making and fixing in position PANELLING as per design made out of 18mm HDHMR Board, finished with appropriate fabric of desired quality and shade over frame made out of 19mm block bload 75mm wide, members placed at 600 c/c bothways complete in all respects with all accessories, fittings and fixtures to the full satisfaction of the Department.

FRAMED BOTH SIDE TEXTILE DISPLAY- Supplying, making and fixing in position BOTH SIDE TEXTILE DISPLAY of size 2100X1200, frame made of 75mm wide 19mm block board, covered with 5.5mm HDHMR Board, and base of 18mm HDHMR Board, and finishd with fabric including all necessary accessories of desired quality and shade to the full satisfaction of the Curator and the Department.

FRAMED BOTH SIDE TEXTILE DISPLAY WITH ROLLERS- Supplying, making and fixing in position BOTH SIDE TEXTILE DISPLAY of size 2400X1200, frame made of 75mm wide 19mm block board, covered with 5.5mm HDHMR Board with provision for installing 38mm rollers (roller blind type) on top and bottom for hanging of display clothes including all necessary accessories of desired quality and shade to the full satisfaction of the Curator and the Department. (Rate of Fabric to be measured and paid separately

Supplying and providing 1st Class Contractor for making any Museum items not there in the estimate to the full satisfaction of the curator

Supplying and placing in position LA SEDE HIGH BACK CHAIR (Chairman, Vice Chariman, Secretary) with full leather finish as per layout to the complete satisfaction of the Department (Admin Building)

Supplying and placing in position OXBO MID BACK CHAIR (General Office, all chairs) as per layout to the complete satisfaction of the Department (Admin Building)

Supplying and placing in position AERO CHAIR LARGER SEAT WITH HR (Main Officers) as per layout to the complete satisfaction of the Department (Officers) (Admin Building)

Supplying and placing in position NANO PERCH 3 SEATER as per layout to the complete satisfaction of the Department (Admin Building)

Supplying and placing in position ZOMPY SINGLE SEATER SOFA as per layout to the complete satisfaction of the Department (Admin Building)

Supplying and placing in position ZOMPY 3 SEATER SOFA as per layout to the complete satisfaction of the Department (Admin Building)

Supplying and placing in position Coffee Table Acura Pro as per layout to the complete satisfaction of the Department (Admin Building)

Supplying and Installing Roller Bilids of approved shade and design, complete in all respects to the full satisfaction of the Department (Admin Building)

Supplying and providing of Jairi Traders Teak Wood Stacking Patio Bench Garden Outdoor Terrance Park Hallway Furniture Wooden Bench Chair Seating with Cushion (4x2 feet) to the full satisfaction of the Department and Museum Curator (Museum)

Supplying and providing of GADWAL FURNITURE Solid Sheesham Wood Wooden Single Seater Sofa Chair Set of 2 for Living Room,Bedroom,Outdoor (Teak Finish) to the full satisfaction of the Department and Museum Curator (Museum)

Supplying and installing RCPL 001: STORAGE 1000 X 500 X 550 showcase made out of pre laminated plywood with 4mm clear glass cover on top including all accessories, fitting, as per design to the full satisfaction of the Department. Glass to be measured and papid separately

Supplying and installing RCPL 002: STORAGE 1000 X 1000 X 550 showcase made out of pre laminated plywood with 4mm clear glass cover on top including all accessories, fitting, as per design to the full satisfaction of the Department. Glass to be measured and papid separately

Supplying and installing RCPL 003: STORAGE 600 X 450 X 600 showcase made out of pre laminated plywood with 4mm clear glass cover on top including all accessories, fitting, as per design to the full satisfaction of the Department. Glass to be measured and papid separately

Supplying and installing RCPL 004: STORAGE 600 X 600 X 750 showcase made out of pre laminated plywood with 4mm clear glass cover on top including all accessories, fitting, as per design to the full satisfaction of the Department. Glass to be measured and papid separately

Supplying and installing RCPL 005: STORAGE 450 X 450 X 750 showcase made out of pre laminated plywood with 4mm clear glass cover on top including all accessories, fitting, as per design to the full satisfaction of the Department. Glass to be measured and papid separately

Supplying and installing RCPL 006: WHITE BOX 450 X 450 X 650 showcase made out of pre laminated plywood with 4mm clear glass cover on top including all accessories, fitting, as per design to the full satisfaction of the Department. Glass to be measured and papid separately

GLASS INSTALLATION ON MANUSCRIPT BOXES: Supply and installation of 8mm clear toughened glass boxes over wooden pedestals in Pandulipi Bhawan with UV pasting to meet the department's satisfaction. This includes procuring high-quality toughened glass, precise installation by skilled professionals, and the application of UV pasting for added protection and aesthetic enhancement. The glass will be crystal clear, durable, and capable of withstanding impact and thermal stress, while the UV pasting will provide resistance against harmful rays and improve privacy. All materials and installation will adhere to required standards and specifications, ensuring a high-quality and visually appealing result.

CNC CUT PARTITIONS: Supply and installation of MDF boards featuring approved make and design, utilizing CNC technology offering seamless integration of precision-cut designs. The high-quality MDF boards shall ensure durability and aesthetic appeal, meeting the stringent requirements of design aesthetics

SUPPLYING OF LAMINATE (Suede Finish): Supplying Laminate of approved shade and quality (SF) for all Panelling, Partitioning and Museum Display Systems to the full satisfaction of the Department

SUPPLYING OF LAMINATE (Microline/Vinnear): Supplying Laminate of approved shade and quality (ML/VNR) for Panelling, Partitioning and Museum Display Systems to the full satisfaction of the Department (ML/VNR only where specified in the Drawing)

PVC WALL CLADDING Supply and installation of PVC louvers on wall or ply board paneling, along with PVC skirting featuring a channel system, designed to match the interior of the building and meet the satisfaction of the department. This includes the procurement of high-quality PVC louvers, precise installation by skilled professionals, and the provision of PVC skirting boards with concealed channels for efficient cable management. All materials and installation will comply with required standards and specifications, ensuring a durable and aesthetically pleasing result. (Annexure C1-3)

WALL PAPER: Supplying and Installing Wall Paper of approved shade and quality on walls and other surfaces as per design, including all requisite materials like gule etc complete in all respect to the full satisfacction of the Department.

SUPPLYING OF CARPET: Supplying Carpet of approved shade and quality for Museum Display Systems to the full satisfaction of the Department

SUPPLYING and INSTALLATION OF COREAN Supplying and Installing Corean of 6mm thickness of approved shade and quality for Museum Display Systems including all accessories such as glue etc. complete in all respects to the full satisfaction of the Department

Supplying and Installing Roller Bilids of approved shade and design, complete in all respects to the full satisfaction of the Department

Supplying and Installing Fibreglass Mannequin (Male/Female) to the full satisfaction of the Curator and the Department

Supplying Hanuman Tape Industries H.T.I Single Sided Self Fusing Silicon Rubber Tape, Length 10 meter

Supplying Black Enamelled 0 Pin No. Entomological Pins, Pack of 100

Supplying Black Enamelled 1 Pin No. Entomological Pins, Pack of 100

Supplying Black Enamelled 2 Pin No. Entomological Pins, Pack of 100

Supplying Black Enamelled 3 Pin No. Entomological Pins, Pack of 100

Supplying Black Enamelled 4 Pin No. Entomological Pins, Pack of 100

Supplying Black Enamelled 5 Pin No. Entomological Pins, Pack of 100

Supplying Black Enamelled 6 Pin No. Entomological Pins, Pack of 100

Supplying Cotton Stockinette (FHPL-PU003)

Orchids Sign Holders Or Stands suitable for paper size (A-4) 210x297mm

Supplying and providing of Carpet Campus Bright Feature Handmade Tufted Woolen Carpet a Medley of Blue & Grey 6 x 8 feet Carpet for Home Living Room Guest Room Bedroom and Also for Hall. to the full satisfaction of the Department and Museum Curator

Supplying and providing of 127mm Sissors (GEM) to the full satisfaction of the Department and Museum Curator

Supplying and providing of Kangaro Carbon Steel Knife (Gem) to the full satisfaction of the Department and Museum Curator

Supplying and providing CERAMICS 25-30 Food Grade Ceramic Plate to the full satisfaction of the Department and Museum Curator

Supplying and profiding of HDHMR Board of size 2400X1200 to the full satisfaction of the Department and the Museum Curator

Supplying and profiding of BWP Grade 18/19mm Plyboard of size 2400X1200 to the full satisfaction of the Department and the Museum Curator

Face Mask

WEBSITE: Development and hosting of Dynamic Website (minimum 8 pages) for Sri Sri Madhavdeva Kalakshetra, including 3 years holsting, domain fees and maintanance charges complete in all respects to the full satisfaction of the Department.

KISOK MANAGEMENT SOFTWARE: Development and installation of Interractive Kiosk Managemennt Software (internet based or server based or stand alone) including content design to be run on Interractive Screens and Interractive Kiosks in for 20 nos of Screens, complete in all respects to the full satisfaction of the Department.

MUSEUM INSTALLATION MANPOWER: Providing of manpower for final installation of Museum Exhibits including 1 nos of Project Curator, 1 nos of Chief Display Conservator, 1 nos of Consevation Display Co-ordinator, 2 Nos of Research Associates, 1 nos of Translator, 1 Nos of Graphic Designer and 1 nos of Artist Co-Ordinator for a period of 10 days to Design and Complete the installation of Museum Exhibits to the full satisfaction of the Chief Curator and the Department

Supplying and installing Fibrglass T-Shapped Mannequin of good quality to the full satisfaction of the curator

Supplying White Polyester fiber Polyfill Fiber Roll, 64mm of good quality to the full satisfaction of the curator

Supplying Curved Beading Needles-2/Pkg to the full satisfaction of the Curator

Supplying Threads (White and Black) as required to the full satisfaction of the Curator

Supplying Super Combed Cotton Elastane Stretch Leggings with Ultrasoft Waistband to the full satisfaction of the Curator

Supplying Soft Nylon Bridal Tulle to the full satisfaction of the Department and Museum Curator

Suppplying White Non Woven Fancy Coat Shoulder Pad, Thickness: 2 - 5 Mm (Pack of 10 pairs)

Supplhying Smooth Archival Fabric to the full satisfaction of the Department and Museum Curator

Supplying Cream Cotton Fabrickw (colour as per curation) Cream Cotton Fabric with 150

Supplying Bangalore Raw Silk Fabric to the full satisfaction of the Department and Museum Curator

Photo Framing and installing with Art Glass ( UV protected 70%, anti-reflected less than 1% ) ART GLASS SIZE : 912 X 1219mm X 2mm on Frame including all other accessories to the full satisfaction of the Curator. Cost of accessories and framing material to be added extra

Photo Framing and installing with Art Glass ( UV protected 70%, anti-reflected less than 1% ) ART GLASS SIZE : 1219 X 1727mm X 2mm on Frame including all other accessories to the full satisfaction of the Curator. Cost of accessories and framing material to be added extra

Photo framing with Fibre Frame for Size : (width: 400-550 height upto 900) including all accessories like mounting board etc to the full satisfaction of the Curator and Department. Price of Glass to be calculated extra

Phot Framing with Wooden Frame for Size : (width 1200 - 1500 to height 1800-2000) including all accessories like mounting board etc to the full satisfaction of the Curator and Department. Price of Glass to be calculated extra

Supplhying and providingTyvek 100mtr roll, 1.5m width, 43 GSM to the full satisfaction of the Department and Museum Curator

Supplhying and providing Streatchable PVC Sheet of width 1.37M, length 50 M to the full satisfaction of the Department and Museum Curator

Supplhying and providing Streatchable PVC Sheet of width 1.8M, length 50 M to the full satisfaction of the Department and Museum Curator

Supplhying and providing Stapler Gun with extra pins (HASHTIP, Alloy steel (15.5 x 11 x 3 cm) to the full satisfaction of the Department and Museum Curator

Supplhying and providing Melinex Polyester Film 1.5 width, 23 micron, 10M Roll to the full satisfaction of the Department and Museum Curator

Supplhying and providing Cotton Voil fabric (Starch free) to the full satisfaction of the Department and Museum Curator

Supplhying and providing Digital Thermohygrometer to the full satisfaction of the Department and Museum Curator

Supplhying and providing Cleaning Brush to the full satisfaction of the Department and Museum Curator

Supplhying and providing Absorbents (Silica Gel) BLU by Absorbia (Pack of 48 -400 ml) to the full satisfaction of the Department and Museum Curator

Supplhying and providing LUX meter with HTC 103 with Calibration Certificate to the full satisfaction of the Department and Museum Curator

Supplhying and providing Nitrile Gloves - M (100 Pack) to the full satisfaction of the Department and Museum Curator

Supplhying and providing Aluminium Pipe 4 inch diametre to the full satisfaction of the Department and Museum Curator

Supplhying and providing Cotton Twill Tape (50 yard/1 inch) to the full satisfaction of the Department and Museum Curator

Supplhying and providing Soft and hard Net Tulle fabric to the full satisfaction of the Department and Museum Curator

Supplhying and providing Ethafoam Sheet, White, 75X1200X2400 to the full satisfaction of the Department and Museum Curator

Supplhying and providing Fabric for wrapping pedestals and textile panels to the full satisfaction of the Department and Museum Curator

Supplying and providing of Dyed Eri for wrapping display panels (Indigo , 40 inch x 8 feet, Jetuka, 40 inch x 8 feet, Manjistha, 40 inch x 8 feet, Turmeric , 40 inch x 8 feet) to the full satisfaction of the Department and Museum Curator

Supplying and providing SanDisk Pen Drive with 64 GB Storage Capacity and 3 Years Warranty to the full satisfaction of the Department and Museum Curator

Printing on Acrylic Sheet of 6mm thickness of Size 2400mm X 1200mm to the full satisfaction of the Department and Museum Curator

Printing on Canvas of size 2400mm X 1200mm to the full satisfaction of the Department and Museum Curator

Printing on Venile or Sunboard of of thickness 6mm of size 2400mm X 1200mm to the full satisfaction of the Department and Museum Curator

Printing of P hotographs on 300 GSM Matt Multicolour Paper to the full satisfaction of the Department and Museum Curator

Printing of stickers (Matt) to the full satisfaction of the Department and Museum Curator

INSIDE MUSEUM 3D DIORAMA WORK : 3D FRP Sculpture for diorama in various traditional performing pose (5-6 ft) height with traditional costume and backdrop painting of diorama including Conceptualization of Idea , Arrangement of Clay Model ,Sculpting of the model using clay ,Casting of the Dye using fiberglass , Fiber moulding of the model with fiberglass and marble dusting , Installation of the Iron Structure of the model , Both dry and wet sanding of the model, Priming of the mural with duco primer and painting of the mural with duco paint , Transportation and installation of the mural on site location , Final touch up of with duco paint after installation and application of gloss paint – Total 18 pieces

3d Sculpture work ITEM 1: 3D Sculpture work depicting the following sculptures in the form of Terra Cotta medium & Cement Casting Medium • Pankhi Raj Boat ( 4.5 m ) • Hatima Putola ( 1.8 m ) • 2 Nos Terracota Dolls ( 1.8m ) each

Tribeni Constructions Limited (BID ID -246601)