PROVN OF PARKING SHED NEAR BLDG NO NP-92 AT 11 RAPID (H) DEF AND EMP COY PROVN OF HARD STANDING FOR TWO WHEELRS AT CHHATERPATI SHIVAJI AUDITORIUM AND ADD ALT OF TOILET BLOCK OF PSYCHIATRIST AT MH AT AHMEDABAD CANTT

Amount

Notes : (i) The work consists of 03 jobs as under:- JOB (A) : 02/REV WK/A'BAD/2024-25/Q3 JOB (B) : 01/REV WK/A'BAD/2024-25/Q3 JOB (C) : ABD/MW/06/2023-24 (ii) Please refer schedule 'A' notes before quoting the tender. (iii) Amount of Schedule of Credit shall be deducted off line by the department.

Excavating in post holes (or similar holes) in soft/loose soil each n exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm etc complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 using 40mm graded stone aggregate as in foundation filling and mass concrete etc complete all as specified and directed.

S & F Rolled steel sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connectiong plates complete including cutting, grinding, welding etc Fe-290 (Gde E-165) as required complete all as specified.and directed.

S & F for rolled mild steel in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc welding etc Fe-290 (Gde E-165)as required complete all as specified.and directed.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified etc complete all as specified and directed.

S&F Pre- painted galvatume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified as specified

M&L preparation of newly steel surfaces exc 10cm width or girth and applying 2 coats of synthethic enamel paint over a coat of primer etc complete all as specified and directed.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft/loose soil etc complete all as directed.

Removing excavated material not exc. 50m and depositing where directed at a level not exc. 1.5m above the starting point in soils etc complete all as specified and directed.

M&L 100 mm thick PCC 1:4:8 using 40 mm graded stone aggregate as in sub base complete all as specified and directed

M & L for laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand;complete with joints to math size complete all as specified and directed.

M & L Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed.

S&F mild steel 5 to 10mm dia screw bolts machine made with hexagonal or square nuts at one side and screwed the other each screwed end fitted with washers and one hexagonal or square nut e exc 5cm long etc complete all as specified and directed.

S&F Mild Steel of gde Fe 410-W as in plain plates cut to required sizes including forming holes without any attachement etc complete all as specified and directed.

M&L or brickwork with subclass ‘B’ old sized bricks, straight or curved on plan to any radius in half brick thick walls and built in CM 1:4 etc complete all as directed.

M&L for rendering 15mm thick in CM 1:4 on external surfaces of brick walls finished even and fair etc complete all as directed.

M&L for prepration of newly plastered surfaces and applying two coats of colour wash over a coat of white wash etc complete all as directed.

M&L for prepration of newly plastered surfaces and applying three coats of white wash etc complete all as directed.

M&L for hardcore with broken stones or boulders of gauge not exc 63mm spread and levelled in layers not exc 15cm thick watered and well rammed to a true surface etc complete all as directed.

M&L for 25mm thick PCC (1:2:4) type B0using 12.5mm graded stone agg as in Top surfaces finished even and fair complete all as specified and directed.

M&L machine cut Kota stone slab 18 to 20 mm thick as in flooring or trades of step incl half round moulding over and including screed bed 15 mm thick in CM (1:6) laid & jointed with grey cement slurry mixed with pigment to match the shade of the slab including cutting, rubbing and polishing complete all as specified.

M&L machine cut Kota stone slab 18 to 20 mm thick as in riser to step including 10 mm thick rendring in CM (1:4) laid & jointed with grey cement slurry mixed with pigment to match the shade of the slab including cutting, rubbing and polishing complete all as specified.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) including removing the rubbish off the premises complete all as specified and directed.

Taking down chowkats or framed with shutters ( without taking off shutters from the frame) not exc 1.5 Sqm each complete all as specified and directed.

Taking Up or down 15mm bore of pipes steel tubing and connections complete all as specified and directed.

Taking Up or down 20mm bore of pipes steel tubing and connections complete all as specified and directed.

M&L for Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match incl and over screed bed or bedding layers of mortar 15mm thick in CM 1:6 in floors complete all as specified and directed

M&L for Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick on wall dado set and jointed in neat cement slurry and pointed in white or colour cement to match incl 10mm thick backing coat of tiles in CM (1:4) Complete all as specified.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube,single,side prelam sheet used instead of plain colour PVC sheet & edges will be painted to match with prelam sheet complete all as specified and directed.

S&F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame complete all as specified and directed.

M&L brickwork with sub class B bricks straight or curved on plan exc 6mtr mean radius built in cement mortar 1:4 all as speified and directed .

M&L 15mm thick rendering in cement mortar 1:6 on other than fair face of brick work or concrete surface complete all as specified and directed.

Supply only integral water proofing compound conforming to IS :2645-1975 specification complete all as specified and directed

M&L for preparation of new plastered surfaces of wall and applying two coats of oil bound distember over a coat of alkali resistant primer complete all as specified and directed

S&F Low density poly ethylene pipes (LDPE) of pressure rating 6 kg/ cm2 of bore dia 15mm laid in trenches or fixed to walls ,or in floors etc complete all as speceified and directed

S&F Low density poly ethylene pipes (LDPE) of pressure rating 6 kg/ cm2 of bore dia 20mm laid in trenches or fixed to walls , or in floors etc complete all as speceified and directed

S&F in repair Bib taps( long body) 15mm bore of, cast copper alloy chromium plated fancy type, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed

S&F Vitreous China wash down water closet pan (pedestal pattern), white including supplying and fixing seat cover , flushing cistern and flushing pipe complete all as specified and directed.

S&F health faucet with one metre tube and hook complete all as specified and directed (cat Part BEA 86 of make Prayag or equivalent make).

S&F Viterous china Squatting pan orrissa Pattern size 580x440mm white with integral foot rest and fixing of flushing cistern and flushing pipe ( supply of flushing cistern and flush pipe seperately) including lime concerte bedding complete all as specified and directed .

S&F in repairs PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and directed

S&F in repairs Vitreous China wash basin, white, flat back, size 500x400 mm including waste coupling, waste pipe of 32mm dia complete all as specified and directed .

S&F PVC connections 600mm long 15mm size with PTMT nuts complete all as specified and directed

S&F Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts,of 15mm bore complete.

S&F Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts,of 15mm bore complete.

S&F in repairs stop cock 15mm dia cast copper alloy CP fency type with long shank and cup conceal type complete all as specified and directed.

S&F in stop cock 15mm dia cast copper alloy CP fency type with long shank and cup conceal type complete all as specified and directed.

S&F Stainless Steel butt hinges medium weight 100mm long complete all as specified and directed.

S&F Aluminium anodised barrel tower bolt of extruded section 150 mm size complete all as specified and directed.

M&L for 150mm long extructed aluminium handle fabricated type complete all as specified and directed.

S & F grating doom 125 mm dia of PTMT complete all as specified and directed.

S&F in repair Grating doom 100 mm dia of PTMT (Minimum weight 25 gms) with wste hole/without waste hole complete all as specified and directed by Engineer in Charge

S&F in repairs 75mm bore for PVC (SWR) floor trap, plain with grating including jointing with solvent cement including jointing with solvent cement..complete all as specified and directed.

S&F in repair brass CP shower rose 125 mm size with or without swivel joint and fixing to steel pipe complete all as specified and as directed

S&F towel rail 600mm long of PTMT fixed with and incl CP brass screws and wooden / plastic cleats (Minimum wt 170 gms) complete all as specified and directed.

S&F Liquid soap container of PTMT fixed with & incl CP brass screws and wooden / plastic cleats (Minimum wt 105 gms) complete all as specified and directed.

S&F soap dish as per CAT Part No BA-45 of make PRAYAG complete all as specified and directed.

S&F Tee grid suspension system of size 600 mm x 600 mm type-1 made out of roll framed hot dipped galvanised steel zince coated of not less than 120 gm/Sqm, main runner 0.3 mm thick of section 24 mm x 33 mm crross runner 0.30 mm thick of section 24 mm x 25 mm, wall angle shall be 0.63 mm thick of section 24 mm x 24 mm grid shall be suspended by 4 mm dia adjustable quick fit hanger rod, system exposed portion shall be pre painted polyester coated in off whitee/white in colour complete with material, fixing, jointing etc., with Coloured textured designer ceiling board (Everest)/Asbestos Cement white fiber Board 4mm thick of size 595 x 595 mm fixing with screws/clips complete all as per manufacturers instructions and direction.

S&F low density polyethylene (LDPE) pipes of pressure rating 6 kgf/sq. cm 32mm dia bore complete all as specified and directed.

S&F PVC (SWR) gully trap 125/110mm. Setting & jointing with solvent cement complete all as specified and directed.

S&F in repairs 75mm bore for PVC (SWR) pipes single socketed in any length with rubber joints, laid in trenches or in floor complete all as specified and directed.

S & F 110mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors incl fittings and fixtures like bend , elbow,tee etc.complete all as specified and directed.

Demolition of old concreate Brickwork or stone/boulder masonry,built in cement mortar including ashlar facings,dressed stonework,precast concreate articles and precast concreate block walling complete all as specified and directed

S&F aluminum anodised power coated ventilator with fixed aluminum frame of size 65 x40 x1.96mm thick fixed in vertical position with aluminum vertical members and one portion to be provided with 4mm thick pin head glass and remaining portion to be louvered using 4mm thick pin head glass and lovered portion covered with stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm incl necessary opening for exhaust fan if required and necessary channel frame worrk with rubber gasket and alumiunm beading etc all as specified

M&L for point wiring with 1100 volts grade PVC insulated FR-LSH multistranded copper conductor cable 1.5 sqmm (Phase - R Y B, Neutral - Black) and earth continuity conductor 1.5 sqmm (Green) drawn into and including concealed rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and sunken galvanized pressed modular steel terminal boxes of thickness not less than 1.2 mm covered with suitable and required size of modular box, plate with cover for mounting modular switches, sockets, fan regulators complete including making good the wall surfaces with matching colour on wall for the following

(a)One light point controlled by one switch.

(b) One fan/Ex fan point controlled by one switch.

(b)One socket outlet 6 amp controlled by one switch on the same board with other switches.

(c)One socket outlet 6 amp controlled by one switch o n indepdendent board.

M&L for point wiring with 1100 volts grade PVC insulated FR-LSH multistranded copper conductor cable 2.5 sqmm (Phase - R,Y,B, Neutral - Black) and earth continuity conductor 2.5 sqmm (Green) drawn into and including concealed rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and sunken galvanized pressed steel terminal box of thickness not less than 1.2 mm covered with suitable and required size of modular box, plate with cover complete for one 16 amp socket outlet controlled by one switch on independent board including making good the wall surfaces with matching colour on wall complete all as specified and directed

(a)S&F switch piano flush button single pole one way 6 amp complete.

(b)S&F switch piano flush button single pole one way 16 amp complete.

(c)S&F socket outlet 2 in 1, 3 pin 6 & 16 amp flush type complete.

(d)S&F socket outlet 2 in 1, 2 & 3 pin, 6 amp, flush type complete.

(e)S&F ceiling rose 3 plates polycarbonate body complete.

M&L for earthing complete with galvanized steel earth plate electrode 60cmX60cmX6mm thick buried directly in ground (earth plate not less than 2.25 mtr deep below the normal ground level) with top edge of plate not less than 1.5 mtr below the normal ground level connected to galvanized earth lead wire of 4.0mm dia by means of nuts bolts, washers, check nuts of iron or steel including PCC pits and RCC cover in PCC 1:2:4 (type B-1) and necessary earth work in any type of soil medium grade GI watering pipe 20 mm dia with funnel and wire mesh and 15mm bore GI pipe light grade protection pipe upto test point etc including excavation and charcoal, common salt surrounded with 15cm all around the plate all as specified and shown in EP-5 of SSR Part-I. all specified

S&F MCB distribution board ETPN, 415 volts, 4 ways powder coated, CRCA steel sheet constructed as per IS : 8623, degree of protection IP 43 - IK 09 with metal door, recess mounted, having insulated 100 amp tinned copper bus bar, neutral busbar, earth bar, din bar, detachable gland plate, interconnection, earthing connection, blanking plates in unused spaces as required.

S&F LED batten (1.2 m) made of Aluminium housing with a PC glossy diffuser duly prewired connection having a nominal system lumen output of 2000 lumens at a minimum system efficacy of 100+ lumens per watt and total power consumption not less than 20 watt including driver. It has a rated system life time of 40000 burning hours at L70 and should have a color temperature of 6500K, CRI>80, THD < 10% and PF > 0.95 complete all as specified and directed.

S&FLED 20W streetlight made up of pressure die cast housing with prismatic polycarbonate diffuser and individual LED's with secondary optics and IP65 protection complete with fixing arrangement and connections as directed

Supply, laying and testing cable XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 25 sqmm 4 core.

Excavating in trenches in Hard / dense / soft soil, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation of poles, trenches for laying of cable, etc. and getting out complete all as specified and directed.

Removing excavated material to a distance not exceeding 50 Mtr and deposting where directed at a level not exc. 1.5 mtr above the starting point.

Returing filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm each all as required and directed.

Supply and laying DWC(Double wall corrugated) HDPE pipe,ISI marked,IS 16205(part 24):2017 part 2 of outer dia 50 mm and inner dia 38 mmwith smooth internal and profiled external surface for non pressure underground cable including all connected acceseries like coupler,o-ring etc complete all as specified and directed Make : Rex Polyextrusion/Gemini/Astral

S&F MCBs as per load requirement 'C' series of breaking capacity 10 KA, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs of following ratings:-

(a) Single pole 6 to 32 amp.

(b) Double pole 32 amp.

© Four pole 63 amp.

Taking down carefully surface aluminium or copper point wiring with PVC casing-caping (light, fan, socket, bell or power) including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc and making good disturbed surfaces complete.

Point wiring with 1100 volts grade PVC insulated FRLSH multistranded copper conductor cable 2.5 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 2.5 sqmm (Green) drawn into and including concealed rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and sunken galvanized pressed steel terminal box of thickness not less than 1.2 mm covered with 3 mm thick phenolic laminated white sheet cover for one 16 amp socket outlet controlled by one switch on independent board complete all as specified and directed.

M&L for submain wiring alongwith earth continuity conductor with PVC insulated FRLSH multistranded copper conductor cable (Phase - Red, Neutral - Black, Earth - Green) drawing into and including concealed rigid non metallic PVC conduit, medium grade, ISI marked ivory colour along with accessories of following nominal sizes:-

(a) 2x6 sqmm + 1x6 sqmm earth continuity conductor in 20 mm dia conduit..

S&F MCB distribution board SPN, 240 volts, 8 ways powder coated, CRCA steel sheet constructed as per IS : 8623, degree of protection IP 43 - IK 09 with metal door, recess mounted, having insulated 100 amp tinned copper bus bar, neutral busbar, earth bar, din bar, detachable gland plate, interconnection, earthing connection, blanking plates in unused spaces as required.

S&F air ventilation fan 250 mm in toilet in rectangular in shape, PVC body, white colour 230V including louber shutter complete all as specified and directed.

Taking down carefully aluminium or copper submain wiring with PVC surface conduit or casing caping and making good disturbed surfaces complete all as specified and directed.

Taking down MCB distribution boards with incoming and outgoing controls any make, any capacity after disconnecting complete all as specified and directed.

DMA PROJECTS (BID ID -3138474)

ARTI CONSTRUCTION (BID ID -3140091)

SNEH TRADERS (BID ID -3144230)

SANVI ASSOCIATES (BID ID -3146853)

UNIT ENGINEERS (BID ID -3147080)

GIRNAR CONSTRUCTION (BID ID -3138212)