Extension and up gradation of The Officers Club along with interior acoustic and associated works at STPS

Amount

Civil Works

Earth work in excavation of foundation trenches or drains, in all sorts of soil (including mixed soil but excluding laterite or sandstone) including removing, spreading or stacking the spoils within a lead of 75 m. as directed. The item includes necessary trimming the sides of trenches, levelling, dressing and ramming the bottom, bailing out water as required complete.(a) Depth of excavation not exceeding 1,500 mm.

Earth work in filling in foundation trenches or plinth with good earth, in layers not exceeding 150 mm. including watering and ramming etc. layer by layer complete. (Payment to be made on the basis of measurement of finished quantity of work) (a) With earth obtained from excavation of foundation

Filling in foundation or plinth by silver sand in layers not exceeding 150 mm as directed and consolidating the same by thorough saturation with water, ramming complete including the cost of supply of sand. (payment to be made on measurement of finished quantity) by fine sand.

Pre-Constructional Anti-termite measures: (a) Anti termite treatment to bottom surface ( in case of masonry foundation and basements) and the sides (upto a height of 300 mm. from bottom) of the excavation trenches with chemical emulsion by admixing chloropyrofos emulsifiable concentrates (1% concentration) with water by weight at the rate of 5 Litres per sq. m. area. The work shall be carried out as per specification described in 6.2.1. of code IS- 6313 (part -II) 1981. (Mode of measurment will be the plan area of foundation treated.)

Anti termite treatment to the top surface of the consolidated earth within plinth walls with chemical emulsion by admixing chloropyrofos emulsifiable concentrates (1% concentration) with water by weight at the rate of 5 Litres per sq. m. of the surface before sand bed or sub-grade is laid. Holes upto 50 mm. to 75 mm. deep at 150 mm. centre to centre both ways shall be made with 12 mm, diameter mild steel rod on the surface to facilitate saturation of the soil with the chemical emulsion. The work shall be carried out as per specification described in para 6.4 of code IS- 6313 (part -II) 1981. ( Mode of measurment will be per Sq.m of plan area of plinth treated.).

Cement concrete (1:3:6)with graded stone ballast (40 mm size excluding shuttering) In ground floor (A) [Pakur Variety]

Hire and labour charges for shuttering with centering and necessary staging upto 4 m using approved stout props and thick hard wood planks of aproved thickness with required bracing for concrete slabs, beams and columns, lintels curved or straight including fitting, fixing and striking out after completion of works (upto roof of ground floor) a) 25 mm to 30 mm thick wooden shuttering as per decision & direction of Engineer-In-Charge.

25 mm. thick damp proof with cement concrete (1:1.5:3) (with graded stone aggregate 10 mm. normal size) and painting the top surface with a coat of bitumen [VG.40 ] using 1.7 kg. per sq.m. including heating the bitumen and cost and carriage of all materials complete. [Bitument to be supplied by the Agency]

Neat cement punning about 1.5mm thick in wall,dado,window,sills,floor,drain etc. Note:-Cement 0.152cum per 100sqm.

200 mm th. Brick work with fly ash bricks set in cement sand mortar(1:6) in/c prackingout joints curing,scaffolding etc. complete in all respect.

Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface] i) with 1:6 cement morter a)15mm thk. Plaster

Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface] i) with 1:4 cement morter a)15mm thk. Plaster

Brick soling with picked jhama bricks including preparation of bed as necessary with brick joints properly filled in and packed with powdered earth and including necessary cushion of similar material below the soling (and in between layers when more than one layer is used) completes as per direction. (a) Single brick flat soling (thickness 75 mm.)

Applying Interior grade Acrylic Primer of approved quality and brand on plastered or cencrete surface old or new surface to receive Distemper/ Acrylic emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer's specification and as per direction of the EIC. (In Ground Floor) (a) One Coat i) Water based interior grade Acrylic Primer

Applying Acrylic Emulsion Paint of approved make and brand on walls and ceiling including sand papering in intermediate coats including putty (to be done under specific instruction of Superintending Engineer) : (Two coats) i) Standard Quality

Applying Exterior grade Acrylic primer of approved quality and brand on plastered or concrete surface old or new surface to receive decorative textured(matt finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface thoroughly, complete as per manufacturer's specification and as per direction of the EIC. In ground floor b) Two coat

Protective and Decorative Acrylic exterior emulsion paint of approved quality, as per manufacturer's specification and as per direction of Engineer-in-Charge to be applied over acrylic primer as required. The rate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer. In Ground floor (Two Coat) c) Super Protective 100% Acrylic Emulsion.

Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction. (a) For works in foundation and upto roof of 1st floor. (i) Tor steel/Mild Steel (a) For works in foundation and upto roof of ground floor/upto 4 m I. SAIL/ TATA/RINL

Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevant IS codes. (i) Pakur Variety

Supplying solid flush type doors of deluxe decorative (both side) quality, conforming to I:S 2202 timber frame consisting of top and bottom rail and side styles of well seasoned timber 65mm wide each and the entire frame fitted with 27.5mm wide battens places both ways in order to made the door of solid core and internal lipping with teak, mahogony or rose wood approved decorative veneers using phenol formaldehyde as glue etc. complete, including fitting, fixing the shutters in position but excluding the cost of hinges and other fittings in ground floor: (a) 35mm thick shutters (single leaf)

Supplying,fitting & fixing of 2-Track / 3-Track Aluminium sliding Window of all Aluminium sections viz. window frame (top,bottom & side frame), shutter (top, bottom, side & interlock member) made of aluminium alloy extrusions conforming to IS 733-1983 & IS 1285-1975, annodised conforming to IS 1868-1983, fitted with all other accessories viz. PVC roller, EPDM gasket, maruti lock, screws etc. including labour charges for fitting & fixing of aluminium 2-track/3-track sliding window with fixing of glass (excluding cost of glass) all complete as per architectural drawings and direction of Engineer-in-charge. 10-12 Micron thickness Annodizing film Natural white 3-track Aluminium window

Supplying bubble free float glass of approved make and brand conforming to IS: 2835-1987. v) 6mm thick clear glass.

Cleaning the walls and ceiling by scraping, sand papering and smoothening down the surface including putting.

M.F. suspended ceiling made with 12.5 mm thick Gypsum plaster board including G.I. perimeter channel of 0.55 mm flush (having two flanges 20 mm and 30 mm respectively and web 27 mm ) along with perimeter of ceiling with G.I. intermediate channel of 0.9 mm thick size 45 mmx15mm placed at 750 mm c/c with G.I. ceiling angle of size 25 mmx10mmx0.55 mm thick fixed to the ceiling with G.I. Cleat and steel expansion fastener ceiling section 0.55 mm thick of size 51.50 mmx26mm fixed to the intermediate channels with the help of connecting clip and in the direction of perpendicular to the intermediate channel of 300 mm c/c 12.5 mm thick Gypsum plastered board are to be fixed under ceiling section as above by machine screws. The boards are to be joined and finished with jointing compound, paper tape and application of top coat etc. as per the direction of Engineer-in-charge. (The rate includes of cost of all materials including taxes, cost of accessories, fittings and fixtures, scaffolding and labour charges etc. complete) In ground floor

Priming one coat on timber or plastered surface with synthetic oil bound ,primer of approved quality including smoothening surface by sand papering etc.

Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc.

Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary : (a) On timber or plastered surface :With super gloss (hi-gloss) -(i) Two coats (with any shade except white)

Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary : (b) On steel or other metal surface :With super gloss (hi-gloss) -(i) Two coats (with any shade except white)

Rendering the Surface of walls and ceiling with White Cement base WATER PROOF wall putty of approved make & brand.(1.5 mm thick)

Supplying,fitting & fixing UPVC pipes A-Type and fittings conforming to IS:13592-1992 with all necessary clamps nails ,in/c making holes in walls,floor etc. cutting trenches in any soil through masonary concrete structure etc if necessary and mending good dameges in/c joining with jointing materails (spun yarn ,Valamoid/Bitumen/M-Seal etc) complete…... A) UPVC Pipes : i) 110 mm Dia

Supplying,fitting & fixing UPVC pipes A-Type and fittings conforming to IS:13592-1992 with all necessary clamps nails ,in/c making holes in walls,floor etc. cutting trenches in any soil through masonary concrete structure etc if necessary and mending good dameges in/c joining with jointing materails (spun yarn ,Valamoid/Bitumen/M-Seal etc) complete…... b)bend 87.5 degreei)110 mm dia

Applying 2 coats of bonding agent with synthetic multi functional rubber emulsion having adhesive and water proofing properties by mixing with water in proportion (1 bonding agent : 4 water : 6 cement) as per Manufacturer's specification [Cement to be supplied by the Department]

A)Iron butt hinges of approved quality fitted & fixed with ISI mark. ii)100mmx50mmx1.25mm

Iron socket bolt of approved quality fitted & fixed complete. e)300mm longx10 mm dia bolt

Supplying, fitting and fixing M.S. clamps for door and window frame made of flat bent bar, end bifurcated with necessary screws etc. by cement concrete(1:2:4) as per direction. (Cost of concrete will be paid separately) a) (a) 40mm X 6mm, 250mm Length

Iron haspbolt approved quality supplied fitted & fixed all complete ( Oxidised) with 16 mm dia e rod with centre bolt and round fitting. c) 300 mm long

Anodised aliminium D-type handle of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 230/72) fitted and fixed complete: (vii) 150 mm grip x 12 mm dia rod.

Door stopper.(Brass)

Wood work in door and window frame fitted and fixed complete in/c a protective coat of paint at the contact surface of the frame.(The quantum should be corrected upto three decimals) a)Local sal

Ordinary Cement conc (1:2:4) with graded trap stone chips Ex/cl shuttering and reinforcement if any in ground floor. i) Pakur variety

Supplying, fitting and fixing windows and ventilators with or without integrated grills conforming to IS 1038-1975 and manufactured from rolled steel sections conforming to IS 7452-1974 with non-friction projecting type, box type hinges, glazing clips, lugs locking bracket, handle plate etc, including hoisting in position, straightening if required, fixing lugs in cement concrete ( 1:2:4) with stone chips 20 mm down cutting holes and mending good damages to match with existing surface complete in all respect excluding glazing. (b) Openable steel windows as per IS sizes with side hung shutters and horizotal glazing bars. [The extra rate admissible for the openable portion only]

Collapsible gate with 40mm x 40mm x 6mm Tee as top and bottom guide rail, 20mm x 10mm x 2mm vertical channels 100mm apart in fully stretched position 20mm x 5mm M.S. flats as collapsible bracings properly rivetted and washered including 38mm steel rollers including locking arrangements, fitted and fixed in position with lugs set in cement concrete and including cutting necessary holes, chasing etc. in walls, floors etc. and making good damages complete.

Supplying, fitting and fixing Fan Hook for ceiling with 1 metre long 16mm. dia rod complete including mending damages. Payment for damage and repair to be made separately.

Removal of rubbish,earth etc. from the working site and disposal of the same beyond the compound, in conformity with the Municipal / Corporation Rules for such disposal, loading into truck and cleaning the site in all respect as per direction of Engineer in charge.

Supplying and laying true to line and level Double Charge Vitrified Tiles of approved brandconforming to IS 15622: 2006 (Group B I a) and tested as per IS 13630:2006 (relevant parts) [Non-modular sizes for tiles with Water Absorption (av.) ≤ 0.08 %] in floor, skirting etc. set in 20 mm thick sand cement mortar (1:4) bed prepared after application of slurry using 1.75Kg of cement per Sqm over the base and 2mm thick cement slurry using cement @2.91Kg./sqm at the back side of the tiles and laid over the mortar bed using 0.2 kg/sqm of White cement used for joint filling with approved pigment as directed and removal of wax coating of top surface of tiles with warm water and polishing the tiles using soft and dry cloth upto mirror finish complete including the cost of materials,Iabour and all other incidental charges complete true to the manufacturer's specification and direction of Engineer-in-Charge. (Note: This work should not be executed without specific permission of Superintending Engineer); (b) ln Ground FIoor:(size not Iess than 800mmX 800 mm X 10.2 mm thick) For Ground Floor

Supplying and laying true to line and level Double Charge Vitrified Tiles of approved brandconforming to IS 15622: 2006 (Group B I a) and tested as per IS 13630:2006 (relevant parts) [Non-modular sizes for tiles with Water Absorption (av.) ≤ 0.08 %] in floor, skirting etc. set in 20 mm thick sand cement mortar (1:4) bed prepared after application of slurry using 1.75Kg of cement per Sqm over the base and 2mm thick cement slurry using cement @2.91Kg./sqm at the back side of the tiles and laid over the mortar bed using 0.2 kg/sqm of White cement used for joint filling with approved pigment as directed and removal of wax coating of top surface of tiles with warm water and polishing the tiles using soft and dry cloth upto mirror finish complete including the cost of materials,Iabour and all other incidental charges complete true to the manufacturer's specification and direction of Engineer-in-Charge. (Note: This work should not be executed without specific permission of Superintending Engineer); (b) ln Ground FIoor:(size not Iess than 800mmX 800 mm X 10.2 mm thick) For 1st Floor

Supplying & laying as per IRC-SP:063-2004 paver unit of any shade of approved quality as per relevant IS code, laid in pattern as directed in pavement, footpath, driveway (paver block only), etc including necessary underlay complete in all respect with all labour and material.(c) 60 mm thick interlocking designer concrete paver block M- 35 grade for light-traffic zone,commercial & office complex,tourist resort as per IS: 15658-2006 (over 20-40 mm medium sand bed on 250mm thk WBM/ WMM base course & 250 mm thk bound gnaular /granular sub-base course including cost of sand for sand bed but excluding cost of base ,sub-base course & subgrade preparation.) ii) Coloured Decorative

Artificial stone in floor, dado, staircase etc with cement concrete (1:2:4) with stone chips, laid in panels as directed with topping made with ordinary or white cement (as necessary) and marble dust in proportion (1:2) including smooth finishing and rounding off corners including raking out joints or roughening of concrete surface and application of cement slurry before flooring works using cement @ 1.75 kg/sq.m all complete including all materials and labour. In ground floor.3 mm. thick topping (High polishing grinding on this item is not permitted with ordinary cement).(i) 20 mm. thick

SANITARY WORKS Ordinary Cement conc (1:2:4) with graded trap stone chips Ex/cl shuttering and reinforcement if any in ground floor. i) Pakur variety

Ordinary Cement conc.(mix 1:1.5:3) with graded trap stone chips (20mm nominal Size) ex/cl shuttering and reinforcement if any,in ground floor as per relevant IS codes. i) Pakur Variety

Hire and labour charges for shuttering with centering and necessary staging upto 4 m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams and columns, lintels curved or straight including fitting, fixing and striking out after completion of works (upto roof of ground floor) (a) 25 mm to 30 mm shuttering without staging in foundation

Reinfiorcement (for reinforced conc.work) in/c distribution bars strirrups binders etc. in/c streightending and removal of loose rust (if necessary) cutting to requisite length,hooking and bending to correct shape,placing in proper position and binding with 16 gauge black annealed wire at every intersection complete as per direction.a) For works in foundation,basement and upto roof of ground floor/upto 4m. i) For steel/Mild Steel

200 mm th. Brick work with fly ash bricks set in cement sand mortar(1:6) in/c prackingout joints curing,scaffolding etc. complete in all respect.

100mm thk. Brick work with ash bricks

Neat cement punning about 1.5mm thick in wall,dado,window,sills,floor,drain etc. Note:-Cement 0.152cum per 100sqm.

Plaster (To wall,floor etc.)with sand and cement mortar in/c rounding off or chamfering corners as directed and racking out joints in/c throating,nosing and drip course. Scaffolding/staging where necessary(Ground floor.) i) With 1:6 cement mortar (a) 20 mm thick plaster

Plaster (To wall,floor etc.)with sand and cement mortar in/c rounding off or chamfering corners as directed and racking out joints in/c throating,nosing and drip course. Scaffolding/staging where necessary(Ground floor.) ii) With 1:6 cement mortar a)15mm thk. Plaster

Plaster (To wall,floor etc.)with sand and cement mortar in/c rounding off or chamfering corners as directed and racking out joints in/c throating,nosing and drip course. Scaffolding/staging where necessary(Ground floor.) iii) with (4:1) cement mortar a)10mm thk.plaster

Rendering the surface of walls and ceiling with white cement based wall putty of approved make and brand(1.5mm thick).

Artificial stone in floor dado staircase etc. with cement conc. (1:2:4)with stone chips,laid in pannels as directed with topping made with ordinary or white cement (as necessary) and marble dust in proportion (1:2) in/cl smooth finishing and rounding off coeners in/c raking out joints or roughening of concrete surface and application of cement slurry before flooring works using cement @ 1.75 kg/sqm all complete in/c all materials and labour. i) 20mm thick

Renewing M.S clamps for door and window frame made of flat bent bar,end bifurcated with necessary screws etc. In cement concrete (1:2:4) in/c cutting of brick work. a) 40mmx6mm,200mm length

Supplying,fitting & fixing UPVC pipes A-Type and fittings conforming to IS:13592-1992 with all necessary clamps nails ,in/c making holes in walls,floor etc. cutting trenches in any soil through masonary concrete structure etc if necessary and mending good dameges in/c joining with jointing materails (spun yarn ,Valamoid/Bitumen/M-Seal etc) complete…... UPVC Pipes : i) 110 mm Dia

Bend 87.5 degree i)110 mm dia

75 mm. Dia. Pipe

Bend 87.5 degree, 75 mm. Dia.

Supplying, fitting and fixing fibre reinforced polymer (FRP) Composite door frame as per approved section with glass fibre reinforced plastic moulded skins and a special sandwich core, so as to impart monolitaheic composite structure as per approved technology of Department of Science and Technology (DST) to safisfy IS: 4020 door testing performance criteria. (i) 66mm x 70mm

Supplying, fitting & fixing fibre reinforced polymer (FRP) Composite door shutters as per approved design with glass fibre reinforced plastic moulded skins and a special sandwich core, so as to impart monolitaheic composite structure as per approved technology of Department of Science and Technology (DST) to satisfy IS:4020 door testing performance criteria. In ground floor.i)25mm thick

Suppling best Indian sheet glass panes set in puty and fitted and fixed with nails and putty complete.(in all floors for inter nal wall & upto 6 m height for external wall) i) 3mm thick (weighting 7.4 kg/sq.m)

A)Iron butt hinges of approved quality fitted & fixed with ISI mark. i)100mmx50mmx1.25mm

Iron socket bolt of approved quality fitted & fixed complete. a)150mm longx10 mm dia bolt

Iron haspbolt approved quality supplied fitted & fixed all complete ( Oxidised) with 16 mm dia e rod with centre bolt and round fitting. a) 250mm long

Iron door handle of approved quality fitted and fixed complete i)100mmx5mm

Applying Interior grade Acrylic Primer of approved quality and brand on plastered or cencrete surface old or new surface to receive Distemper/ Acrylic emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer's specification and as per direction of the EIC. (In Ground Floor)(a) One Coati) Water based interior grade Acrylic Primer

Applying Acrylic Emulsion Paint of approved make and brand on walls and ceiling including sand papering in intermediate coats including putty (to be done under specific instruction of Superintending Engineer) : (Two coats) i) Standard Quality

Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc.

Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary :(a) (b) On steel or other metal surface :With super gloss (hi-gloss) -(i) Two coats (with any shade except white)

Applying decorative cement based paint of approved quality after preparing the surface including scraping the same thoroughly (plastered or concrete surface) as per manufacturer's specification. In Ground floor: (i) One coat on new surface.

Applying Exterior grade Acrylic primer of approved quality and brand on plastered or cencrete surface old or new surface to receive decorative textured (matt finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer's specification and as per direction of the EIC. In Ground Floor: (a) One Coat

Protective and Decorative Acrylic exterior emulsion paint of approved quality, as per manufacturer's specification and as per direction of Engineer-in-Charge to be applied over acrylic primer as required. The rate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer. In Ground floor (Two Coat) a) Premium 100% Acrylic Emulsion

M.S.or W.I. Ornamental grill of approved design joints continuously welded with M.S, W.I. Flats and bars of windows, railing etc. fitted and fixed with necessary screws and lugs in ground floor. (i) Grill weighing above 10 Kg./sq.mtr and up to 16 Kg./sq. mtr.

Surface Dressing of the ground in any kind of soilingcluding removing vegetation inequalities not exceeding 15 cm depth and disposal of the rubbish within a lead upto 75 m as directed.

Supplying, fitting, fixing C.I Grating (Heavy type).(b) Above 100 mm and upto 150 mm Square or round.

Construction of septic tank of different capacities as per approved drawing with 1st class brick work in cement mortar (1:4) including two 560 mm dia. R.C.C. manhole cover(heavy type)of approved make supplied, fitted and fixed in the 100mm thick R.C.C (1:1.5:3) top slab with necessary fittings, 20mm thick cement plaster (4 : 1) with neat cement finish to the internal surfaces and 15 mm thick cement plaster (4 : 1) to outside wall upto 200 mm below G.L floor finished with 25 mm thick grey artificial stone over 100 mm thick R.C.C(1:1.5:3) bottom slab including supplying, fitting and fixing all necessry specials, fittings, S.W. tees, C.I. foot rest etc. including excavation earth in all sorts of soil, shoring, bailing out and pumping out water as necessary,ramming, dressing the bed and fefilling the sides of the tanks with earth, removing spoils, filling up the chamber with clear water, removing foreign materials from the chamber and including constructing attached inspection pit as per approved drawing and connecting all necessary pipes, joints etc. with internal plaster work and artificial stone flooring is to be done with admixture of water proofing compound @ 0.5% by weight of cement with all costs of labour and materials. Note:- (i) Finished level of Septic Tank should be 400 mm. from Ground Level. (ii) Height of 50 mm. Ventilation pipe & Mosquito proof mesh, should be follwed as per IS:2470,Part- I.Payment will be made separetly on the basis of actual height based on relevant I.S.Code. (i) For 10 users A) With Pakur variety. (SAIL/TATA/RINL)

Construction of circular soak well 2.5 metre deep in all types of sandy soils with dry brick work upto 1.6 metre from the bottom having 150 mm intermediate cement brick work (1:4) band all round and cement brick work (1:4) upto 0.90 metre from top with 20mm thick cement plastering (1:4) to inside face upto the depth of cement brick work, 15mm thick cement plaster (1:4) on outer face from top of the well upto G.L. and 6 mm thick cement plaster (1:4) on top of the R.C.C. cover slab including filling bottom 1.00 metre of inside of the well with brick metal (50 mm to 63 mm size) including R.C.C. cover slab of 100 mm thick with cement conc (1:1.5:3) with stone chips with necessary reinforcement and shuttering including one 560 mm dia. R.C.C. manhole cover (heavy type)of approved make supplied, fitted and fixed in the cover slab with necessary fittings, making nacessary arrangements for pipe connections, excavation of well including shoring, dewatering and removing the exess earth from the premises as per direction complete in all respect with all costs of labour and materials. With 250 mm thick dry brick work and 250 mm thick cement brick work (1:6) and 1.00m inside dia. SAIL/TATA/RINL)

Supplying, fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc. (A) Floor With Sand Cement Mortar (1:4) 20 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m & joint filling using white cement slurry @ 0.20kg/Sq.m. (a) Area of each tile upto 0.09 Sq.m(i) Coloured decorative

Supplying, fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc. (B) Wall With Sand Cement Mortar (1:3) 15 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m & joint filling using white cement slurry @ 0.20kg/Sq.m. (a) Area of each tile upto 0.09 Sq.m (i) Coloured decorative

Supplying and laying true to line and level Double ChargeVitrified Tiles of approved brand conforming to IS 15622: 2006 (Group B I a) and tested as per IS 13630:2006 (relevant parts) [Non-modular sizes for tiles with Water Absorption (av.) ≤ 0.08 %] in floor, skirting etc. using polymerised adhesive of 6mm thick layer applied directly over finished artificial stone floor/Mosaic etc without any backing course and joints grouted with admixture of white epoxy grout materials of approved brand including spacer -2mm as directed and removal of wax coating of top surface of tiles with warm water and polishing the tiles using soft and dry cloth upto mirror finish complete including the cost of materials,Iabour and all other incidental charges complete as per direction of Engineerin- Charge. (Note: This work should not be executed without specific permission of Superintending Engineer) (a) ln Ground FIoor:(size not Iess than 600mmX 600 mm X 9.5 mm thick)

Supplying, fitting and fixing Marble Slab/tile of 15 to 18 mmm thickness in floor, lobby, stair, landing & treads etc. over 20 mm (av.) thck base of Cement mortar (1:2) laid with white cement slurry @ 4.4 kg/Sq.m before placing marble & jointed with white cement slurry @ 2.0 kg/Sq.m with necessary pigments including grinding and Granite polishing as per direction of Engineering -in -Charge in Ground Floor. {White cement and Pigment to be supplied by the Agency] (ii) Area of each Slab/tile exceeding 0.3 sq.m. but not exceeding 0.6 sq.m.

Supplying, fitting and fixing in position G.I. pipes of TATA make for underground works with all necessary accessories,specials viz.socket, bend, tee, union, cross, elbow, nipple, short piece etc.including cost of all materials,jointing materials ,cutting pipes,making threads,cutting trenches upto 1.5 metre below surface in all sorts of soil and refilling the same as directed with two coats of painting on G.I. pipes and specials with bituminous paint complete in all respect. (Payment will be made on the centre line measurement of the total pipe line including all specials No separate payment will be made for accessories, specials.Payment for painting will be made seperately) (i) 15 mm dia. medium quality

Supplying, fitting and fixing PVC pipes for underground work of approved make of Schedule 80 (medium duty) conforming to ASTMD -1785 and threaded to match with GI Pipes as per IS : 1239 (Part - I). with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted including cost of all materials ,jointing materials, cutting pipes, making threads ,cutting trenches upto 1.5 metre below surface in all sorts of soil and refilling the same as directed complete in all respect. (Payment will be made on the centre line measurement of the total pipe line including all specials No separate payment will be made for accessories, specials.) PVC Pipes a) 20mm

Wash basin vitreous china of approved make (without fittings) supplied,fitted and fixed in position on 75mm X 75 mm X 75 mm wood blocks and C.I. brackets including two coats of painting of C.I. brackets. (i) 450 mm X 300 mm size

Supplying, fitting and fixing Flat back urinal (half stall urinal) in white vitreous chinaware of approved make in position with brass screws on 75 mm X 75 mm X 75 mm wooden blocks complete. (i) 470 mm X 280 mm X 340 mm

Supplying, fitting and fixing bib cock or stop cock. Chromium plated concealed Stop Cock heavy duty (Equivalent to Code No. 5083 & Model - Florentine of Jaquar or similar brand).

Supplying, fitting and fixing bib cock or stop cock. Chromium plated angular Stop Cock with wall flange (Equivalent to Code No. 5053 & Model - Florentine of Jaquar or similar brand).

Supplying, fitting and fixing shower of approved brand and make. (a) (i) Chromium plated round shower with revolving joint 100 mm dia with rubid cleaning system (Equivalent to Code No. 542(N) & Model - Tropical / Sumthing Special of ESSCO or similar brand).

(ii) Chromium plated shower arm 240 mm long (Equivalent to Code No. 536(A) & Model - Tropical / Sumthing Special of ESSCO or similar brand).

Supplying, fitting and fixing pillar cock of approved make. a) (i) CP Pillar Cock - 15 mm. (Equivalent to Code No. 507 & Model - Tropical / Sumthing Special of ESSCO or similar brand).

Supplying, fitting and fixing bib cock or stop cock. (i) CP 2-way bib Cock - 15 mm, supplied, fitted and fixed. (Code No.5041 & Model - FLORENTINE of JAQUAR or similar brand).

Supplying, fitting and fixing towel rail with two brackets. (a) C.P. over brass (i) 25 mm dia. and 450 mm long

Supplying, fitting and fixing best quality Indian make mirror 5.5 mm thick with silvering as per I.S.I. specifications supported on fibre glass frame of any colour, frame size 550 mm X 400 mm

Supplying, fitting and fixing soap holder. (a) PTMT (Prayag or equivalent)

STRUCTURAL WORK FOR BADMINTON COURT Earth work in excavation of foundation trenches or drains, in all sorts of soil (including mixed soil but excluding laterite or sandstone) including removing, spreading or stacking the spoils within a lead of 75 m. as directed. The item includes necessary trimming the sides of trenches, levelling, dressing and ramming the bottom, bailing out water as required complete.(a) Depth of excavation not exceeding 1,500 mm.

Earth work in filling in foundation trenches or plinth with good earth, in layers not exceeding 150 mm. including watering and ramming etc. layer by layer complete. (Payment to be made on the basis of measurement of finished quantity of work) (a) With earth obtained from excavation of foundation

Filling in foundation or plinth by silver sand in layers not exceeding 150 mm as directed and consolidating the same by thorough saturation with water, ramming complete including the cost of supply of sand. (payment to be made on measurement of finished quantity) by fine sand

Cement concrete (1:3:6)with graded stone ballast (40 mm size excluding shuttering) In ground floor (A) [Pakur Variety]

Hire and labour charges for shuttering with centering and necessary staging upto 4 m using approved stout props and thick hard wood planks of aproved thickness with required bracing for concrete slabs, beams and columns, lintels curved or straight including fitting, fixing and striking out after completion of works (upto roof of ground floor) a) 25 mm to 30 mm thick wooden shuttering as per decision & direction of Engineer-In-Charge.

Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevant IS codes. (i) Pakur Variety

M.S. structural works in columns, beams, tube etc. with simple rolled structural members (e.g. joists, angle, channel sections conforming to IS: 226, IS: 808 & SP (6)- 1964 connected to one another with bracket, gussets, cleats as per design, direction of Engineer-in-charge complete including cutting to requisite shape and length, fabrication with necessary bolting, metal arc welding conforming to IS: 816- 1956 & IS: 1995 using electrodes of approved make and brand conforming to IS:814- 1957, haulage, hoisting and erection all complete. The rate includes the cost of rolled steel section, consumables such as electrodes, gas and hire charge of all tools and plants and labour required for the work including all incidental charges such as electricity charges, labour insurance charges etc. Payment to be made on the basis of calculated weight of structural members only in finished work as per IS specified weight. Payment for gusset, bracket, cleat, rivets, bolts and nuts may be make by adding the actual weight of such items with the weight of finished structural members or 7% of weight for finished structural members weighing not less than 22.5 Kg. / m. or 15 % of weight for finished structural members weighing less than 22.5 Kg. / m. may be increased allow for bracket, cleat, rivet, bolts and nuts etc. and no separate payment being made for these items, as per direction of Engineer In Charge. The rates are considered for a height of erection 8m. / 2nd floor level from the ground. Add 1.5% extra over the rate for each additional floor or 4m beyond initial 8m. or part thereof. I) For built up sections / structural members of specified sections weighing not less than 22.5 Kg./m

Labour charges for Gas cutting and shifting of steel structure including stacking of steel structure as directed, welding in M.S. structural work with gas or electric, dismantling and removal of rubbish,earth etc. from the working site and disposal of the same beyond the compound within a lead of 75 m.in all respect as per direction of Engineer in charge.

Galvanised or painted wind-tie made of M.S. flats, fitted and fixed complete including cost of necessary fittings. (a) Made with 40 mm. X 6 mm. Flats (Materials will not be supplied by the Deptt.)

Supplying, fitting & fixing 1.5mm thick Trapezoidal profile corrugation Polycarbonate clear sheet made of national brand, excluding the supporting frame work, fitted and fixed with 10mm dia x 55mm Self-driving screws, EPDM washers and putty complete with 150mm end lap and one corrugation minimum side lap complete as per specification & direction of Engineer-in-charge including materials, labour, taxes and all other incidental charges (Payment to be made on area of finished work). In Roof

Supplying, fitting and fixing glass reinforced polyester translucent fiber glass sheet to match with GCI Corrugation as per IS: 12866 - 1989 in roof fitted and fixed with 10 mm dia "J" or "L" hook, bolts and nuts, limpet and bitumen washers and putty with 150mm end lap and one corrugation minimum side lap complete. b) 2.0mm +/- 0.2 mm thick sheet.(3.25Kg/Sq.m) i) Natural white or tinted blue colour

ACOUSTIC WORK FOR CLUB HALL Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface] i) with 1:4 cement morter a)15mm thk. Plaster

Scraping of moss, blisters etc.thoroughly from exterior surface of walls necessitating the use of scraper, wire brush etc.(Payment against this item will be made only when this has been done on the specific direction of the Engineer-in-charge)

Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc.

Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary :(b) On steel or other metal surface :With super gloss (hi-gloss) -(i) Two coats (with any shade except white)

Applying Interior grade Acrylic Primer of approved quality and brand on plastered or cencrete surface old or new surface to receive Distemper/ Acrylic emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer's specification and as per direction of the EIC. (In Ground Floor) (a) One Coat i) Water based interior grade Acrylic Primer

Applying Acrylic Emulsion Paint of approved make and brand on walls and ceiling including sand papering in intermediate coats including putty (to be done under specific instruction of Superintending Engineer) : (Two coats) i) Standard Quality

Rendering the Surface of walls and ceiling with White Cement base WATER PROOF wall putty of approved make & brand.(1.5 mm thick)

French polishing to wood work including preparing surface (ordinary gloss) (b) On old French polished surface including complete removal of the old polish.

Supplying, fitting and fixing boiling water proof ply conforming to IS: 710-1977 bonded with phenol formaldehyde synthetic resin conforming to IS: 848-1974 of approved make and brand fitted and fixed as per design as per approval and direction of Engineer-in-Charge. [excluding the cost of supporting frame work and teak wood batten/Lipping] In Ground Floor (iv) 12mm

Supplying fitting, fixing decorative lamination conforming to IS: 2046 : 1995 as per approved make, brand, finish and thickness with fitting, fixing the same on Particle/MDF / Ply Boards with recommended / approved adhesive with proper clipping the sides for better attachment as per direction of Engineer-incharge. The rate includes the cost of labour, adhesive and all incidental charges thereof. In ground floor; Glossy/Matt/Suede excluding surface texture or metallic lustre. (i) Thickness of laminate 1.5mm

Suppling, fitting and fixing Auto hinge

Suppling, fitting and fixing full decorative 6 inch S.S Handle

Suppling, fitting and fixing full decorative 10 inch S.S Handle

Supplyimg and fitting fixing wall wooden paneling by 12 mm ply and finish by 3 mm-4mm veneer with melamine polish.

Supplying fitting and fixing of vertical blind.

Accoustic Treatment in wall paneling : Supplying and fixing wall paneling which includes stud section (0.55 mm thick having web of 70 mm , unequal flanges of 36 mm and 34mm made of GI sheet) placed horizont. Finally the boards are to be jointed and finished so as to have a flush look which includes fitting and finishing the tapered and tapered and square edges of the boards with jointing compound. joint paper tape and two coats of drywall topcoat as suitable for.

200 mm th. Brick work with fly ash bricks set in cement sand mortar(1:6) in/c prackingout joints curing,scaffolding etc. complete in all respect.

Supplying solid flush type doors of deluxe decorative (both side) quality, conforming to I:S 2202 timber frame consisting of top and bottom rail and side styles of well seasoned timber 65mm wide each and the entire frame fitted with 27.5mm wide battens places both ways in order to made the door of solid core and internal lipping with teak, mahogony or rose wood approved decorative veneers using phenol formaldehyde as glue etc. complete, including fitting, fixing the shutters in position but excluding the cost of hinges and other fittings in ground floor: (a) 35mm thick shutters (single leaf)

GREEN ROOM Supply and fixing of mirror of 5mm thick with a backing of 12mm ply (BWR) with moulding wooden bit in the all edge size approx 900mm height from table top.

Supply and fixing of mirror of 5mm thick with a backing of 12mm ply (BWR) with moulding wooden bit in the all edge size approx 900mm x 1800 height from floor level.

Supply and placement of dressing table of size 2400mm x 461mm D x 510mm H. Made of 19 mm and 12mm ply with 1.5mm laminated finish as per approved design of EIC.

Revolving type chair full chusion type without arm for green room.

Supply and placement of table of size 1200mm x 1050mm D x 750mm H. Made of 19mm and 12mm ply with 1.5mm laminated finish as per approved design of EIC.

Electrical Works

Supply Fitting & fixing of moduler board, size: 8” x 12”

Supply Fitting & fixing of modeler board, size: 8” x 6”

Supply Fitting & fixing of modeler board, size: 6” x 4”

Supply Fitting & fixing of modeler board, size: 4” x 4”

Supply Fitting & fixing of 5/6 amps Piano type Switch, Make- Havells/ Goldnedal

Supply Fitting & fixing of 5/6 amps Piano type Socket, Make-Havels/ Goldnedal

Supply Fitting & fixing of 15/16 amps Piano type Switch, Make- Havells/ Goldnedal

Supply Fitting & fixing of 15/16 amps Piano type Socket, Make-Havels/ Goldnedal

Supply Fitting & fixing of Angular Holder make-Anchor / Goldnedal

Supply Fitting & fixing of Round Block

Supply Fitting & fixing of Ceiling Rose Make- Goldnedal

Supply Fitting & fixing of LED Tube Light set size 4feet, Make- Havels / Phillips /Goldnedal

Supply Fitting & fixing of LED Street Light 120 Watt make – Havels / Goldendale / CGL

Supply Fitting & fixing of SPN 25 Amp RCCB make- Havels / Goldnedal / L&T

Supply and Laying of PVC insulated Copper Wire, Counseled Wiring & Copper Earth wire of the following sizes. Make- Gold Star /Finolex Size : Size : 2x1 [1.5 sq. mm.] sp. Mm.

Supply and Laying of PVC insulated Copper Wire Counseled Wiring & Copper Earth wire of the following sizes. Make- Gold Star /Finolex Size : 2x1 [2.5 sq. mm.] sp. Mm.

Supply and Laying of PVC insulated Copper Wire Counseled Wiring & Copper Earth wire of the following sizes. Make- Size : Gold Star /Finolex Size : 4x1 [1.5 sq. mm.] sp. Mm.

Supply and Laying of PVC insulated Copper Wire Cashing Wiring & Copper Earth wire of the following sizes. Make- Havells / Mescab /Finolex Size : 3x1 [4 sq. mm.] sp. Mm.

Supply and Laying of PVC insulated Copper Wire Cashing Wiring & Copper Earth wire of the following sizes. Make- Havells / Mescab /Finolex Size : 4x1 [10 sq. mm.] sp. Mm.

Supply and Laying of PVC insulated Copper Wire Cashing Wiring & Copper Earth wire of the following sizes. Make- Havells / Mescab /Finolex Size : 1x1 [0.75 sq. mm.] sp. Mm.

Supply, Fitting & Fixing of 10Amps MCB with Box

Supply, Fitting & Fixing of 6 way MCB panel

Supply, Fitting & Fixing of 100AMP TPN MCB

Supply, Fitting & Fixing of 70 Sq. mm 3 ½ core Armored Cable deputed ISI make.

Fitting & Fixing with supply of Ceiling Fan

Supply, Fitting & Fixing of Exhaust Fan Dia 12” Make- Crompton Greaves

320Amp. 415V Aluminum bus bar arrangement to number 200M incomer MCCB and 01 number 320A bus coupler MCCB Along with 03 numbers 100M and 07 number 63M out going MCCB and bus bar chamber panel details made by 2mm (14SWG) thick steel material mold steel, dust vermin proof. Panel size – 3’x3.5’x1.5’, front operating handle, mine incoming and outgoing cables shall be bottom entry and vertical cable way for each section rear bus to have facility to open.

Supply , fitting of pipe earthling .

IMPERIAL MARBEL

M/s. SARKAR AND SARKAR