Construction of Science Laboratory Block at Degree College Kargil

Amount

Earth work in excavation by mechanical means (hydraulic excavator) in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed, within a lead of 50 metres: as directed by Engineer-in-charge.

ALL KINDS OF SOIL 80%

ORDINARY ROCK 20%

Filling available excavated earth (excluding rock) in trenches plinth, sides of foundation etc in layer not exceeding 20cm in depth consolidating each deposited layer by ramming and watering, lead upto 50cm and lead up to 50 m and lift upto 1.5 mtr.

STONE SOLLING Dumping of stone including cost of stone (in horizontal on level) including all carriage complete

Providing and laying position cement concrete of specified grade excluding the cost of centering and shuttering. All work upto plinth level 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 20 mm nominal size) (crushed) including all carriage complete

Providing and laying position cement concrete of specified grade excluding the cost of centering and shuttering. All work upto plinth level 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) (crushed) including all carriage complete

Reinforced cement concrete work in footings , pedestal , columns , beams, suspended floors, roofs having slope upto 15°, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto five level including curing but excluding the cost of centring, shuttering, finishing and reinforcement with M25 Nominal Mix 1:1:2 (1 cement : 1 coarse sand : 2 graded stone aggregate 20 mm nominal size) including all carriage complete

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level Thermo-Mechanically Treated bars of grade Fe-500D or more. including all carriage complete

Centering and shuttering including strutting, propping etc. and removal of form for: Foundation, footing bases of column

Centering and shuttering including strutting, propping etc. and removal of form for: Columns, pillars, piers, abutments, posts and struts.

Centering and shuttering including strutting, propping etc. and removal of form for: Lintel, beams, plinth beams, girders, bressumers and cantilevers.

Centering and shuttering including strutting, propping etc. and removal of form for: Suspended floors, roofs, landings, balconies and access platform.

Providing and laying autoclaved aerated cement blocks masonry with 450-100 mm thick AAC blocks in superstructure above plinth level upto floor V level in cement mortar 1:4 (1 Cement : 4 coarse sand ) and curing complete. The rate includes providing and placing in position 2 nos. 6 mm dia M.S bars at every third course of masonry work. including all carriage complete

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or dash fastener shall be paid for seperately) First class Kail Wood including all carriage complete

Providing and fixing panelled and glazed shutters for doors, windows and clerestory windows, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for seperately,all complete as per direction of Engineer-in-charge.(second class teak wood 35 mm thick shutter)

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40mm thick.Second Class teak wood

Providing and fixing factory made uPVC AIS or FENISTA or KOEMMERLING make wood Finish colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sashshall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately) Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. (Double Glazed Unit or SHGC with <0.25 and >0.35 VLT may be introduced.) including all carriage complete

Casement cum fixed panel window having both end single casement panel, middle fixed panels and at top completely fixed ventilator with S.S friction hinges (350 x 19 x 1.9) made of (big series) frame 67 x 60 mm , sash 67 x 80 mm &mullion 67 x 80 mm all having wall thickness of 2.3 ± 0.2 mm and single glazing bead/double glazing bead of appropriate dimension. (Area of window above 3.00 sqm upto 5.00 sqm).

Providing and fixing factory made uPVC of AIS or FENISTA or KOEMMERLING make Wood Finish colour fixed glazed windows/ventilators comprising ofuPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerancein dimension i.e. in depth & width of profile shall be acceptable. Variation inprofile dimension in higher side shall be accepted but no extra payment on this account shall be made. (Double Glazed Unit or SHGC with <0.25 and >0.35 VLT may be introduced. including all carriage complete

Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.)

Providing and fixing casement handle made of zinc alloyed (white powder coated) for UPVC casement window with necessary screws etc. complete.

Providing and fixing upto floor five level precast cement concrete solid block including hoisting and setting in position with cement mortor 1:3 (1 cement : 3 coarse sand), cost of required centering, shuttering complete: 1:2:4 ( 1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size including all carriage complete

CEMENT PLASTER (IN COARSE SAND) 12mm Cement plaster of mix 1 : 4 ( 1 cement : 4 coarse sand) (PPC or cement with >25% flyash is recommended.)

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade on New work (two or more coats) over and including priming coat with water thinnable cement primer (Note: It Should have Low or No VOC as per Green Building guidelines)

Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives. (Note: It Should have Low or No VOC as per Green Building guidelines)

New work (Two or more coats applied @ 1.43 litre/10 sqm. Over & including priming coat of exterior primer applied @ 0.90 litre/10 sqm. (Note: It Should have Low or No VOC as per Green Building guidelines)

Applying priming coat: With ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood) (Note: It Should have Low or No VOC as per Green Building guidelines)

Preparing newly primed wooden surface for painting by way of filling of putty sand papering rubbing complete.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade: Two or more coats on new work. (Note: It Should have Low or No VOC as per Green Building guidelines)

Providing and fixing DGU ( with <0.25 SHGC and >0.35 VLT glazing in uPVC window, ventilator shutters and partitions etc. with proper sealing as per norms etc. complete as per the architectural drawings and the directions of engineerin- charge. ( Note : DGU with <0.25 SHGC and >0.35 VLT)

TOUGHENED DGU glass panes of 5.0 mm thickness SAINT GOBAIN / ASAHI INDIA GLASS / HNGIL make as approved by engineer in charge Qty vide window openings @80%

Providing & Fixing finished brass hanging type floor door stopper with necessary screws etc complete.

Providing and laying vitrified floor tiles in different sizes (thickness tobe specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete i.e Size of tile 600x600 mm

P/F 1st quality ceramic glazed wall tiles conforming to IS:15622 600MM X 600MM (thickness to be specified by the manufacturer) of approved make in colours, shades except burgundy bottle green, black of any size as approved by engineer-in-charge in Skirting, risers of steps, and dados, over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 course sand) and jointing with grey cement slurry @3.3kg/sqm including pointing the joint with white cement and matching pigments etc., complete.

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge :

Flamed finish granite stone slab Jet Black, Cherry Red, EliteBrown, Cat Eye or equivalent

Providing and fixing water closet squatting pan ( Indian type W.C. pan) with 100 mm sand cast Iron P or Strap, 4/2 litre low level P.V. C. flushing cistern including flush pipe (of approved make) "manually controled device (handle lever) conforming to IS:7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required. (Note : It should have flush rate of with Flush rate of 4/2 Litre per Flush or less ) (Dual flush 4/2L WC cistern with bottom inlet for compact back to wall Rimless toilet)

Orissa pattern white vitreous china W.C. pan of size 580x440 mm with integral type foot rests. JAGUAR/CERA Make

Providing and fixing white vitreous china pedestal type water closet EWC (European type W.C . .pan) with seat and lid, 4/2 litre low level white P.V.C. flushing cistern including flush pipe with manually controlled device (handle lever) conforming to IS:7231, with all fittings and fixtures, complete including cutting and making good the walls and floors wherever requied: (Note : It should have flush rate of with Flush rate of 4/2 Litre per Flush or less )

W.C. pan with lSI marked white solid plastic seat and lid. JAGUAR/CERA Make

Providing and fixing wash basin with C.I./M.S. brackets, 15mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required:

White Vitreous China Square Shaped Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps JAGUAR / CERA/HINDWARE Make

P/F of mirrors of superior glass with plastic moulded frame(of approved quality) and of required size and shape. With 6mm thick hard board backing. Rectangular Shape 1500 x 450 mm

Providing and fixing soil waste & vent pipe (Prince)

PVC Pipe. 110mm dia (10 feet unit Length)

PVC Pipe. 75mm dia (10 feet unit Length)

PVC Bend 110mm dia

PVC Bend 75mm dia

PVC Tee 110mm dia

PVC Tee 75mm dia

PVC Collar 110mm dia

PVC Collar 75mm dia

PVC trap 110mm dia

PVC trap 75mm dia

PVC Socket 110mm dia

PVC Socket 75mm dia

PVC door junction 110mm dia

PVC door junction 75mm dia

CPVC PIPES AND FITTINGS Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having Chemical Resistant property , thermal stability for hot and cold water supply, including all CPVC plain and brass threaded fittings. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-charge.

Internal work-exposed on wall, including fixing the pipe with clamps at 1.00 meter spacing 50mm nominal outer dia pipes.

Providing and fixing 3 layer Thermex Pipe PP-R (Poly propylene Random copolymer)pipes conforming to IS: 15801, UV stabilized and anti-microbial fusion welded, having thermal stability for hot and cold water supply including all PP-R plain and brass threaded Polypropylene random fittings. This includes testing of joints complete as per direction of Engineer-incharge.Internal work Concealed fixing the pipe with clamps at 1.00 meter spacing including cutting chases and making good the wall, Tee, Elbow , Union, Junction. Threat etc.

PN-16 pipe , 25mm OD(SDR-7.4)

PN-16 pipe , 32mm OD(SDR-7.4)

P/F CP brass toilet paper holder including cost of wodden,PVC,play etc.

Providing and fixing Wall mount Liquid Soap Dispenser of approved brand

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.

450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms

Providing and fixing accessories of standard and quality make of approved manufacturer including all necessary fixtures required.

L-Drops for room door

L-Drops for Windows

T-Bolt For Doors

T-Bolt For Windows

Handles for door

Handels for window

15 mm C.P. brass tap with elbow operation lever

15 mm C.P. brass 2 in 1 tap

Handles with lock system of main doors ( Godrej Make) Godrej Locks COMBIPACK WITH 240mm EURO MORTISE LOCK SEC 02 Combi 2C Antique Brass 7526

Providing and installation of PUF (Puf Insulated Tanks) water tank capacity 1000 ltrs of approved brand (SYNTEX OR ANY OTHER APPROVED BRAND) as per direction engineer incharge

Design Supply and installation/Fixing staircase railling of stainless steel (Grade 304) railing(Top and Bottom Handrail Dia > 50mm , two number intermediate Horizontal tubes Dia >25mm and Rectangular Two Pair Balusters Dia >38mm @1000mm C/C) made of Hollow tubes channels, plates etc. including welding ,grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts, clips and bolts complete ,including fixing the railing with necessary accessories , newal post , balusters and stainless steel dash fasteners, stainless steel bolts etc. of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, necessary screws/fixtures complete job as approved by engineer incharge (Note : No additional payment shall be made to master pillar/Newal Post )

THERMAL INSULATION Providing wood work in frames of walls,false ceiling, partitions etc. sawn and fixed in position :Budloo / Fir wood (Note : False Celling Design should be as per engineer in charge which may be of different level celling )

Providing and fixing 12 mm thick tongued and grooved Pine wood (Soft Wood ) 4-5 inch in width panelling or wall panels in walls and celing includining all necessary fixtures including cornice with necessary screws, priming coat on exposed surface etc., complete. Brand - Rait Wood

Preparing newly prepared panneled surface for polishing by way of filling of putty , sealer and sand papering rubbing and applying hard polish,glossy polish in sequance over the prepared surface complete job

Providing and fixing thermal insulation with specified wool and density conforming to IS: 8183, 50 mm thick, wrapped in 200G Virgin Polythene bags fixed to walls with screws, rawl plugs and washers and held in position by criss-crossing GI wire etc. complete as per directions of Engineer-in-charge.

With resin bonded rock wool with density 48 kg/cum

Providing and laying roof insulation with 40 mm thick impervious sprayed, closed cell free Rigid Polyurethane foam over deck insulation conforming to IS - 12432 Pt. III (density of foam being 40-45 kg/cum), over a coat of polyurethane primer applied @ 6-8 sqm per liter, laying 400 G polythene sheet over PUF spray and providing a wearing course of 40 mm thick cement screed 1: 2 : 4 (1 cement : 2 coarse sand : 4 stone aggregate 20 mm nominal size) in chequered rough finish, in panels of 2.5 m x 2.5 m and embedding with 24 G wire netting and sealing the joints with polymerized mastic, all complete as per direction of Engineer-in-Charge..

Wooden planking, tongued and grooved in flooring including fixing with iron screws complete:

25 - 32 mm thick Second class teak wood

Supply and installation of Reflective Bubble Aluminum Foil Insulation / Aluminium Silver Bubble Sheet 210 GSM (7 mm) Thick Light Weight Reflective Insulation , Max Withstanding Temperature -40 degree To +110 Degree Waterproof insulation all complete

Supply and installation of electrical Underfloor heating mats for floor heating systems non-corrosive, flexible heating elements including cables, pre formed cable mats including smart thermostat and digital electrical control panel all complete (STIEBEL ELTRON / DANFOSS Or any other approved brand

Supply and installation of High Quality self regulating heat tracer for Specialized Heating Solutions for Winterisation of water pipeline including all accessories complete including Supply and installation of Circuit Control Panel with RCBO MCB ,THERMOSTAT (0-120) DEG C, power connector-two way-6 sq.mm, w.p. splice connector,w.p. tee connector,end seal,mounting kit-w.p. jb,g.i. pipe strap 4",al. adhesive tape roll ( 50 mm w x 20 m l),f.g. adhesive tape roll (DANFOSS Make OR CHROMALOX any other approved brand as per the direction of Engineer-In-Charge)

Supplying and fixing High Quality 32mm Thick Nitrile Insulation Tube for water pipeline of approved brand 2 Inch Size (Armaflex Class-o Armacell) , rockwool of apparent density 128 Kg/m3 on outer side of nitrile tube of 50mm thickness including alumunium duct clading (Alumunium Sheet Guage Thickness = 0.46MM TO 0.71MM )of approved quality and finish as per the direction of engineer in charge (Nitrile Tube 32mm > Rock Wool 50mm > Alumunium Duct Clading 0.46mm to 0.71mm)

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS:277 and consisting of angle cleats of size 25 mm widex1.6mm thick with flanges of 27mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm diax40mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.5mm of required length with nuts & bolts of required size and other end of angle hanger fixed with G.I. channels 45x15x0.9 mm running at the spacing of 1200 centre to centre, to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26 mm each having clips of 10.5 mm at 450mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64mm diaX230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5mm thick 27mm high having flanges of 20mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre to centre, with 25mm long drive-all screws @ 230 mm interval ,including fixing of gypsum board/calcium silicate board to ceiling section and perimetre channel with the help of dry wall screws of size 3.5x25mm at 230mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the gypsum board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150mm on both sides of joint and two coats of primer suitable for board, all as per manufacturers’ specification and also including the cost of making openings for light fittings, grills diffusers,cutouts made with frame of perimetre channels suitably fixed all complete as per drawing and specification and direction of the Engineer-in-Charge but excluding the cost of painting with:

12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095-Part 1 : 2011 (Board with BIS certification marks)

Providing and fixing precoated galvanized iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Structural steel work in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. WELDED @3.5 Kg/Sft

Flooring with marble stone of specified thickness as per sample of marble approved by Engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement:4 coarse sand) laid and jointed with grey cement slurry including rubbing, polishing and curing complete with: Udaipur green marble (Extra for marble stone flooring in treads of steps and risers using single length up to 2.00 meter.)

Extra for pre finished nosing to treads of steps of marble stone

Supply and installation of ABC Fire Extinguisher, 6 Kg 4Sets (Note : It should be Halon free)

Hi-Flow MP1- 2 HP Centrifugal Pump Havells/Crompton/kirloskar (Note :Pump should be minimum BEE 3 star labelled or above)

Provision for providing and fixing ornamental Shingstak (Ladakhi wood carving over exterior Windows and main entrance door) (Design as per the direction of Engineer-In-charge.) including polishing all complete

Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides with required EPDM rubber / neoprene gasket felt etc. Aluminum sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge (glazing, panelling and dash fasteners to be paid for separately.) 2.5 Kg/m 10 Gauge Thickness

Powder coated aluminum (minimum thickness of powder coated 50 microns)

For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM (2.3 Kg/m 10 Gauge Thickness)

Providing and fixing glazing in aluminum door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineerin-charge. (Cost of aluminum snap beading shall be paid in basic item.)

With float glass panes of 5.0 mm thickness (weight not less than 12.50 kg / sqm)

Stone work (machine cut edges) for wall lining/Cladding etc. 16mm-20mm Thick (veneer work) upto 10 m height, backing filled with a grout of average 12 mm thick cement mortar 1:3 ( 1cement: 3 coarse sand) including pointing in white cement mortar 1:2 ( 1 White cement: 2 stone dust) with an admixture of pigment matching the stone shade and curing complete : (To be securedto the backing by means of cramps which shall be paid for separately):

Providing and fixing of PVC conduits 25mm dia of approved make including bends, elbows, sockets, tees etc. laying in slab/ floor cutting chassis and making good or surface mounted including all fixtures.

Supplying and fixng of deep MS junction boxes for concealed led lights while laying slab/ floor cutting chassis and making good or surface mounted including all fixtures complete job.

MCB Distribution Board S/F Double door MCB distribution boards, 240V/415V, Sheet steel, Powder coated DB’s suitable for MCB’s fitted with Bus Bar, Neutral link, Earth Bar and Din bar of following no. of ways :(Regal Grey

a) 8 Way (8 + 24), Double door T&PN [ DHDNTHCDRW08 ]

b) 12-way, double door SP&N [DHDPSHODRW12]

c) 16 Way, Double door SP&N [ DHDPSHODRW16]

S/F following size/module, GI box along with modular base and cover plate for modular switches/sockets in recess etc. as required:

a) 1 or 2 Module (75mmX75mm)

b) 3 Module (100mmX75mm)

c) 4 Module (125mmX75mm)

d) 6 Module (200mmX75mm)

d) 8 Module (200mmX75mm)

d) 12 Module (200mmX75mm)

Providing and fixing accessories of standard and quality make of approved manufacturer including all necessary fixtures required.

Alumunium L-Drops for door

Alumunium L-Drops for Windows

Alumunium Handles for door

Alumunium Handels for window

SEPTIC TANK Excavation work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.(SIZE 20' X 10' )

ORDINARY ROCK=80%

ALL KIND OF SOIL=20%

Disposal of Mulba/Excavated Earth Beyond 50m (Lead upto 6Km) Outside Town Area (CARRIAGE OF MATERIALS By Mechanical Transport including loading, unloading and stacking)

Providing and laying position cement concrete of specified grade excluding the cost of centering and shuttering. All work upto plinth level 1:3:6 (1 cement : 4 coarse sand : 8 graded stone aggregate 20 mm nominal size) (crushed) MUD MATE including all carriage complete

Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 ( 1 cement : 6 course sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with cement mortar 1:6 ( 1 cement : 6 course sand) and curing complete (Quarry Stone) including all carriage complete

Dry random rubble masonary with hard stone in foundation & plinth using quarry stone with bond stone including all carriage complete

Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto five level including curing but excluding the cost of centring, shuttering, finishing and reinforcement with 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) including all carriage complete

Providing & fixing upto floor five level precast cement concrete solid blocks including hoisting and setting in position in cement mortar 1:3 (1cement:3 coarse sand), cost of required centring, shuttering and curing complete 1:2:4 (1 cement : 2 coarse sand : 4 graded crushed stone aggregate 20 mm nominal size) including all carriage complete

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level Thermo-Mechanically Treated bars of grade Fe-500D or more. including all carriage complete

Centering and shuttering including strutting, propping etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platforms. SEPTIC TANK/SOKAGE PIT

Cement concrete flooring 1:2:4 (1cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry and curing complete, but excluding the cost of nosing of steps etc. complete. including all carriage complete

SEPTIC TANK 50 mm thick with 20mm nominal size stone aggregate.

Supplying and fixing C.I. cover without frame for manholes:

560 mm diameter C.I. cover ( heavy duty) the weight of the cover to be not less than 108 kg

M/S SHITAPA TRADERS

bhatconstructions

M/S MOHD MOHSIN

M/s Yazdaan Constructions

Inder Mohan Gupta

M/S Marvel Associates