KSCB/ALP/3-PTNKD/2025-26

Amount

FURNISHING WORK - "Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5x25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing"

GypsumStepCeiling: Providing and fixing Gypsum Step ceiling with width/ depth less than or equal to 300 mm as per approved design. Frame work made of special sections,powerpressedfromM.S.sheetsand galvanizedwith zinc coatingof 120 gms/sqm (bothside inclusive) as perIS:277, i.e., perimeter channels 0.5 mm thick 27 mm high having flanges of 20 and 30 mmlong to be fixed as per design intent and thick 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095-Part 1 to be fixed on to the framework using 25 mm long drywall screw. Finish the joints using jointingcompound andjointtapaspermanufacturespecification.Includingcost and conveyance of all materials labour charges etc. Complete as per direction of Engineer-in- charge. The visible Vertical Sides will be measured.

Grid type false ceiling :- Providing & Fixing of grid type false ceiling with armstrong tile,Model: Classic Lite RH99 Armstrong. (Classic Lite tiles with Rivel edge black groove grid frames) and armstrong suspension system as per standard specifications of Armstrong world industries including providing cutouts for light fittings etc. complete.

Toughened Glass Providing and fixing door of 12mm thick Toughened glass door (Saint Gobain) with dorma Aido XLC 4000 patch fittings (Floor Spring, Top patch, pivot Pin, Bottom patch) dorma Center lock and handle 24".Including all cost and conveyance of materials, labour, etc complete.

12mm Toughened Glass Partition with plywood frame : Providing and fixing 12mm thick Toughened glass(Saint Gobain) Partition System (upto a height of 300cm ) with 12mm ply and 1mm lamination as per design intent.Including all cost and conveyance of materials, labour etc complete.

Etching Sticker Work: Providing and fixing Etching Sticker as per design intent using suitable adhesive as per manufacture's Specification.Including all cost and conveyance of materials, labour etc complete.

Providing partition wall 80mm/100mm thick using plywood of thickness 12 mm double layer, with a plywood core.Finished with 1mm white or theme lamination on both sides. No quantity is measured in running meter and Quantity is measured only for partitions below the false ceiling.Including cost and conveyance of all materials labour charges etc. complete.

Supplying and fixing 4mm ACP in existing aluminium frame work, as per the specifications and drawing. including cost and conveyance of all materials labour charges etc. complete.

Supplying and fixing flush doors with 32mm block board and 6mm glass as per design and specification finished with 1.00 mm lamination on both sides, the width of the door 75cm/90cm. Use ISI. S.S 304 hardware fittings including locks, handles, hinges, stoppers, door closer, etc. Including cost and conveyance of all materials labour charges etc. complete.

Cladding over the pillars, and solid walls using 12mm PVC board of 0.6 density and finished with 1mm lamination, as per the specifications and drawing. including cost and conveyance of all materials labour charges etc. complete.

Supplying and fixing plywood shelves 45 CM WIDTH provide, hinges, and 8" concealed handles with multi-lock using 19mm block board for the door. Finished with 1mm lamination on both sides. Shelves using 19mm plywood and 12mm PVC board of 0.6 density for the backside. Finished with 0.8mm lamination for the inner sides and 1mm lamination for the outer sides. Quantity is measured only below the false ceiling. Drawings &specifications are given along with. including cost and conveyance of all materials

Making a cash counter unit with Framed in 80mm and 100mm thick partition wall including all sides of cash counter as per drawing made in 12mm double layer, with a plywood core and provides 12mm toughened glass beveled and polished for the front and sides, fixed to the side partition of the counter as per design Provide keyboard tray, cable manager, CPU stand, leg stand, fixed in SS 304 - hardware fittings including locks, tower bolt, and handles. Provide currency reader near cash chest with glass in tabletop and light point with LED bulb, cash drawers, and shuttered cabinets with locks and handles for the counter and 19mm Nano white granite for countertop with side polished. . Finished with 1mm wooden and white lamination on the outer side, and 0.8mm lamination on the inside. An etching sticker should be provided for the glass area as specified. Including cost and conveyance of all materials labour charges etc. complete.

Making table for tellers,manager,senior accountent,auditor,area manager etc, as per design and provide 19mm Nanowhite granite for countertop with side polished. The counter is framed using 19mm- marine ply with a drawer,shelf, keyboard tray , cable manager , CPU stand , leg stands using 12mm plywood, lock,handil,hinges, etc are constructed as per design. Finished with 1mm wooden and white lamination on outer side and 0.8mm on the inside. including cost and conveyance of all materials labour charges etc. complete.

Making side credenza 80x40x60CMs using 19mm and 12mm-ply wood Finished with 1mm wooden and white lamination -on the outer sides and 0.8 mm lamination -on the inner sides. Provide locks and handles for drawers and shutters as per design. Including cost and conveyance of all materials labour charges etc. complete.

Making a paper desk for the customers 65x40x50cms in dimension dimension with a 19mm nano white for the tabletop. All faces of the table using 12 mm plywood, finished with 1mm lamination. Including cost and conveyance of all materials labour charges etc. complete.

Supplying and fixing zebra blinds self-designed or textured of standard quality (approximate cost (total work)160/sqft). Including cost and conveyance of all materials labour charges etc. complete .

Supplying and fitting ready made pin-up notice board(120x90)cms with aluminium frame and velvet core including cost of materials, fitting charges etc. complete

Supplying and fitting 8mm thick glass with vinyle sticker wall logo board(120x60)cms fixing to wall or partition using by ss studs. including cost of materials, fitting charges etc. complete

Pantry Counter, :- Providing table type pantry counters 60 cms wide, 75 cms height, with table top, front apron, vertical dividers 19 mm BWR 303 grade plywood. 5x3 cm wooden frame to be given horizontally below inner edge of counter top for the entire length of the counter. Wooden foot rest of 7.5 x 3 cm size .Counter top to be provided with 20 mm edge bevelled and edge polished granite (jet black). All external surfaces 1 mm laminate finish and internal surfaces with enamel finish. 10mm thick beach wood lipping for all plywood edges.

Wicket doors with Both side Mica:- Providing and fixing 30 mm thick single leaf solid core and resin bonded flush door water proof quality with 1 mm thick lamination on both side external wooden lipping all round the shutters, all as per drawing and instruction. the doors and lamination of approved make, colour and design including all best quality hardware, brass hinges, lock etc;. complete.

Door closer: Supplying and fixing 'everite' make hydraulic door closer including cost and conveyance of all materials, labour charges for fixing, etc. complete as per directions of site incharge.

Dressing table -Supply/ installing wall mounted dressing table with glass mirror as per detailed drawing. Outer sides should be laminated and inner sides painted with two coats of enamel paint over a coat of primer & two coats of putty. (Size of table with mirror-50x45x140)

Floating glass shelf for trophy in Managers room :- Providing 12mm thk edge polished glass shelves of size 100cms length and 20cms width fixed to the Back wall in Managers cabin using adjustable glass shelf supports of SS finish (EBCO/eqlt) The spacing between the glass supports shall be 40cms or as per manufacturers specification.

ELECTRICAL WORKS 1 - Main VDB - "Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure of 6 way (8+18 - double cover TPN vertical DB with provision for fixing FP MCCB as incomer and SP/ TP MCB as outgoings (IP 42/43) including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/ isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required Conforms to IS 8623 - 1&3, IEC 61439 - 1&3."

Main Incomer - Supplying and fitting 100A 4P 35kA 415V 50Hz MCCB with Thermal Magnetic Protection Unit conforming to IS60947-2 & IEC 60947-2.

Outgoings - "Supplying and fitting 63A 3P 415V 50Hz MCB 10kA C curve conforming to IEC 60947-2. For A/CDB & SPARE"

Supplying and fitting 25/32A 3P 415V 50Hz MCB 10kA C curve conforming to IEC 60947-2 For 3phase ups/LDB/ATM

Supplying and fitting 32/16A SP 240V 50Hz MCB 10kA C curve conforming to IEC 60947- 2.For board light and spare

2- AC/DB - "Supply and installation charges of 3 phase 4way (8+12) DB enclosure with bus bars, neutral link earth bus and din rail suitable for fixing 4P MCB AND RCCB as incomer and SP MCB as out goings IP43 including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required Conforms to IS 8623 - 1&3, IEC 61439 - 1&3."

Incomer - 63A 4P RCBO (100mA) conforming to IEC/EN 61009 2010

Outgoings - "Supplying and fitting 10/16A SP 240V 50Hz MCB 10kA C curve conforming to IS/IEC 60898 -1 2002. For power plugs"

Supplying and fitting 20/25A SP 240V 50Hz MCB 10kA C curve conforming to IS/IEC 60898 -1 2002. For single phase A/C Units

LDB - "Supply and installation charges of 3 phase 4 way (8+12) DB enclosure with bus bars, neutral link earth bus and din rail suitable for fixing 4P MCB AND RCCB as incomer and SP MCB as out goings IP43 including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required Conforms to IS 8623 - 1&3, IEC 61439 - 1&3."

Incomer - 40A (30mA) 4P RCBO conforming to IEC/EN 61009 2010

Outgoings - "Supplying and fitting 10/6A SP 240V 50Hz MCB 10kA C curve conforming to IS/IEC 60898 -1 2002."

UPS IP DB : SITC of 6 Way double door SPN DB consisting of the following for UPS

40A 2P RCBO (30mA) as incomer 32 A 2P MCB - 2 Nos

NOTE: The complete alarm systems and CCTV systems power connections must be taken before the output MCB of the UPS connection to ensure continuous power supply to the security systems. separate MCB to be provided near CCTV, Fire Alarm System power points.

UPS OUTPUT:- SITC 32 A DP MCB in metallic enclosure

UPS OUTPUT SUB DB: Supply and installation charges of Single phase 12 way (I/C+O/G) DB enclosure with bus bars, neutral link earth bus and din rail suitable for fixing 2P ISOLATOR as incomer and SP MCB as out goings IP43 including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/ isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required Conforms to IS 8623 - 1&3, IEC 61439 - 1&3.

40A 2P HI RCBO (30mA) - 1no as incomer and following as out goings

10A SP MCB - 10 No ( for CKT & Spare )

INVERTER - "INVERTER CIRCUIT Supply, Installation, testing and commissioning of Inverter input & output using 3 x2.5sqmm 1100V, PVC insulated FRLSH Copper conductor through PVC Conduit . Rate shall be for the average length from VDB to inverter charging, then to inverter input, from inverter output to inverter discharging & connection to change over and to inverter DB.No claim for additional wire and conduit. Following isolators to be provided for inverter charging (input) and discharging (output)"

(a) 25A DP ISOLATOR in metal enclosure for inverter charging

(b) 25A DP ISOLATOR in metal enclosure for inverter discharging

SITC of 25A 2P MCB Type manual Change over switch In metal enclosure with necessory fittings

CONTROL SWITCH (CCTV) :-SITC of 16A Modular switch box with socket and MCB

LIGHTING DB CUTOFF - "Supply, Installation, testing and commissioning 40A 4P MCB IN 4 WAY SPN DB AT ENTRANCE OF BRANCH"

INVERTER DB : Supply and installation charges of Single phase 12 way (I/C+O/G) DB enclosure with bus bars, neutral link earth bus and din rail suitable for fixing 2P ISOLATOR as incomer and SP MCB as out goings IP43 including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/ isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required Conforms to IS 8623 - 1&3, IEC 61439 - 1&3.

40A 2P RCBO (30mA) as incomer

10A SP MCB - 10Nos

Supply & Installation of SURGE PROTECTION DEVICE (TVSS ) - Surge protection device(AC) 3P+N, In-20Ka,Imax -40kA,Up-less than or equal to 4.5kV ,with indicator conforming to IEC/EN 61643-11

POWER CABLE: Supply & laying of XLPE insulated PVC innersheathed aluminium conductor, 1.1 kV grade armoured power cables conforming to IS:7098, as per approved make in ground/ trench/surface/wall/pipe,(a) 4x35 Sq.mm XLPE as incoming cable MSB to VDB

(b) 4x10 Sq.mm XLPE VDB to Light Cutoff and return to LDB

( c ) 4x16 Sq.mm XLPE VDB to To POWER/AC DB

(d) 2x4 Sq.mm XLPE

CABLE TERMINATION Supply and installation (SITC) of End termination of the following size of cables using flange type cable glands and heavy duty tinned aluminium crimping type cable sockets including gland earthing.

(a) 4x35 Sq.mm XLPE

(b )4x16 Sq.mm XLPE

(c ) 4x10 Sq.mm XLPE

(d ) 2x4 Sq.mm XLPE

Supply & laying of 4 x 6sq. mm stranded PVC insulated copper wire through 20mm Rigid PVC condute.

WIRING FOR LIGHT, FAN, PLUG SOCKETS, UPS & EARTHING OF BRANCH COLOUR CODING AS PER IS 732 STANDARD. R Phase - RED COLOUR,Y Phase - YELLOW COLOUR, B Phase - BLUE COLOUR WIRING SYSTEM A - Circuit Main - SITC of all materials and wiring for circuit mains from LDB/Inverter to Switch Boards, using 2.5 sq mm 1100V, PVC insulated FRLSH Copper conductor for phase , neutral including earthing with 1 run of 2.5 sq.mm green copper wire continuous run thorough 25 mm PVC conduit as per IS, giving inter connection etc complete as required and as directed by engineer in charge.Rate shall be for the average length from LDB to the switch board.No claim for additional wire and conduit.

B - Light And Exhaust fan Points -"SITC of all materials and wiring for light and exhaust fan points using color coded 1.5 sq.mm 1100V grade, FRLSH, PVC insulated stranded copper conductor single core stranded wires of IS 694 specification and should have IS marking, through ISI medium grade 20mm rigid PVC conduits concealed in wall / slab/ceiling etc,complete with necessary accessories, including supplying and fixing 6A modular type switch housed in a suitable factory made M. S box with moulded front plate including earthing the box, ceiing rose, connectors (of approved make) etc., complete as required.(The rate include removing debris, packing and rough plastering the grews after conduiting)" (b1) "Single control light Point / Exhaust fan point (one light/fan controled by one switch)" Item rate

C - Group Control Wiring (Lights) (c1) Two lights controlled by one switch Item rate

( c2 ) Three lights controlled by one switch Item rate

(c3) Four lights controlled by one switch

Item rate

D - Supplying all materials and wiring for ceiling fan points with 250 W stepped type electronic regulator using 1.5sq.mm, FRLSH PVC insulated stranded copper conductor single core stranded color coded wires of 1100V grade and 1 run of 1.5 sq.mm green copper wire for Phase , nuetral & earthing continuously run as per IS through ISI medium grade rigid PVC conduits concealed in wall/slab/ceiling etc., complete with necessary accessories, including supplying and fixing 6A modular type switch and 250W electronic fan regulator housed in a suitable factory made M. S. box with moulded front plate including earthing the box,complete as required.(The rate include removing debris, packing and rough plastering the grews after conduiting)

(d1) Ceiling fan point Item rate

( d2) Wall fan point (same as above ) with 6A socket but without electronic regulator Item rate

E - Plug Sockets

(e1) Supplying all materials and wiring for 6A plug points in independent positions using 1.5 sq.mm 1100V, FRLS PVC insulated copper conductor single core stranded wire for phase & neutral and earthing with 1 run of 1.5 sq.mm green copper wire inside the conduit / flat conduit , and fixing 6A modular type plug socket (2 in 1) controlled by 6A switch with moulded front plate, housed in a suitable factory built MS box. Giving connections, earthing etc complete as required. Item rate

(e2) Supplying all materials and wiring for 6A plug points in combined positions using 2 runs of 1.5 sq.mm 110V FRLS PVC insulated copper conductor single core stranded wire, earthing with earthing with 1 run of 1.5 sq.mm green copper wire inside the conduit/flat conduit , and fixing 6A modular type plug socket (2 in 1) controlled by 6A switch with moulded front plate, housed in a suitable factory built MS box. Giving connections, earthing etc complete as required. (in SB) Item rate

(e3) Supplying all materials and fixing modular type 16A power plug point with 16A 3 pin modular type plug socket controlled with 16A switch with moulded front plate, housed in a suitable factory built MS/PVC box using 2 runs of 2.5 sq mm 1100V , FRLSH PVC insulated stranded Copper conductor including earthing with 1 run of 2.5 sq.mm green copper wire continuous run thorough 25 mm PVC conduit as per IS, giving inter connection etc complete as required and as directed by engineer in charge. as per IS, giving inter connection etc complete as required. Rate shall be for the average length from DB to the switch board.No claim for additional wire and conduit. Item rate NOTE: The Electrical Wiring inside the Strong Room should be in a CONDUIT and POWER CUT OFF SYSTEM either AUTO / MANUAL PLUG SYSTEM drawing power only from the Limit Switch in case of "Auto Power Cut Off System" is provided in the Door OR from the FEEDER BOX fitted outside the Strong Room (near the door) in case of Manual Plug System. The MANUAL PLUG SYSTEM OF POWER CUT OFF should be such that the connecting cable passes through the Strong Room Defender Door from inside to outside, which should be accessible only after opening the S.R. door (thus ensuring that the door can not be closed without removing the plug + wire and hence total power inside the Strong Room is cut off leaving no chances of fire resulting from an Electrical source / High Voltage / Surging even with the Switches in Off position). Inverter & KSEB Power inside strong room should be provided through two separate plug and socket arrangements.

F - Computer power point - UPS power stations Supplying all materials and fixing modular type 3numbers 6A, 3 Pin sockets controlled by one number 16A SP control indicator switch with moulded front plate, housed in a suitable factory built MS/PVC box SITC of all materials and wiring for circuit mains from UPS Sub DB to work station using 2 runs of 2.5 sq mm 1100V, FRLSH PVC insulated stranded Copper conductor including earthing with 1 run of 2.5 sq.mm green copper wire continuous run thorough 25 mm PVC conduit as per IS, giving inter connection etc complete as required and as directed by engineer in charge. etc complete as required . Rate shall be for the average length from DB to the primary switch board and looping to adjacent switch boards. No claim for additional wire and conduit. (Maximum 2 points from 1 Circuit)

H -1 Ton A/C Point Supplying all materials and fixing modular type 20 A power plug point with 20A 3 pin socket controlled with 20 A DP modular switch with moulded front plate, housed in a suitable factory built MS box using 4 sqmm 1100 V, FRLS PVC insulated stranded Copper conductor and earthing with 4 sqmm green Cu wire continously run through 25 mm PVC conduit as per IS giving inter connection etc complete as required.(AC point) the switch shall be fixed at a height of 120 cm from finished floor level . Rate shall be for the average length from DB to the switch board. No claim for additional wire and conduit. Item rate

I - 2 Ton/1.5 TON A/C Point Supplying all materials and fixing modular type 32 A power plug point with 32A 3 pin socket controlled with 32 A DP modular switch with moulded front plate, housed in a suitable factory built MS box using 2 runs 4 sqmm 1100V FRLS PVC insulated Copper conductor and earthing with 2.5 sqmm green Cu wire continously run through 25 mm PVC conduit as per IS giving inter connection etc complete as required.(2 Ton AC point) the switch shall be fixed at a height of 120 cm from finished floor level. Rate shall be for the average length from DB to the switch board.No claim for additional wire and conduit. Item rate

J -CASSETTE AC POINT Supplying and fixing 30 A, 415 V, TPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 30 A "C" curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

K -Weather proof IP 65 enclosure for AC outdoor control(to be provided after obtaining approval from Bank) 18 - STABILIZER (a) SITC of 4/5 KVA , V Guard make voltage stabilizer

(b) Supply and fixing 20A plug socket With plug top for AC Stabilizer

19- Board Light Point Supplying all materials ,Wiring for board light point controlled by 20A ELCB in metal enclosure using 2 runs 4 sqmm 1100V FRLS PVC insulated Coper conductor and earthing with 4 sqmm pvc insulated green Copper wire continously run through 25 mm PVC conduit as per IS giving inter connection etc complete as required. Rate shall be for the average length from DB to the board light . No claim for additional wire and conduit. (Board Light point for Branch)

20- SITC OF LIGHT FITTINGS AND FANS

(a ) 36W LED FITTING - Supply and Installation of 2'x2' square LED ceiling flush mounted fitting of Wipro, Elate LED,CRCO10

(b) ROUND LED DOWN LIGHT FITTING Supply and Installation of LED ceiling fitting Wipro Iris LED Slim Ro, LD80-171-XXX-60-XX 1x18W

(c ) ROUND LED FITTING Supply and Installation of LED ceiling fitting Wipro Iris LED Slim Ro, LD80-530-XXX-60-XX 1x9w or equivalent

(d) CALLING BELL Supply and Installation of Calling bell controlled by modular type bell push

(e ) LED TUBE FITTING Supply and Installation of 1x18 W patty LED tube fitting on wall or ceiling Garnet led tube 4feet white

( f) LED bulb - Supply and Installation of 9W LED bulb on angle holder.

(g ) WALL FAN Supply and Installation of 400 mm sweep swivelling type wall fan Crompton Greaves High flo or equivalent

(h) EXHAUST FAN Supply and Installation 150mm light duty exhaust fan with all fittings

(i) EXHAUST FAN Supply and Installation 300mm light duty exhaust fan with all fittings

(j) CEILING FAN Supply and Installation of 1200 mm sweep ceiling fan with all fittings for the installation of Ceiling fan - Crmpton Greaves - white color

(k) CABIN FAN Supply and installation of 300mm sweep cabin fan with plastic body & blade with Grill for protection and can be mounting on ceiling. (l) LED STRIP Supply and fixing strip LED (Warm colour) for false ceiling with good quality driver unit (4A,12V adaptor for 5M ) Formes Led Wipro

(m) Supply and installation of 15W 2ft Watt LED Mirror Lamp luminaire and giving connections.

21 -EARTHING STATIONS (a) Supply and installation of plate earthing satation conforming to IS 3043 using 600x600x6mm Copper plate eath electrode burried in ground, 20mm dia 3m long perforated GI pipe with funnel and constructing inspection chamber by masonry work with heavy duty CI inspection cover including civil work complete for UPS.

(b) PIPE EARTH Supplying of all materials and providing earth point with pipe earthling waste pipe earthling strips, funnel etc. excavation trenches, filling with alternate layers of charcoal, salt ands sand, back filling as per BIS specifications and IS 3043/1987

22- EARTHING CONDUCTORS Supply and laying the following sizes of bare copper earthing conductors including termination,bracing the joints etc. as per standards. (a)2x10 SWG Copper through cables

(b)1x8 SWG Copper for pipe earth

(c)1x10 SWG Copper

23- EARTH BENCH Supply and fixingtinned copper earth bench (minimum 40cm length) 25x3 mm with all termination using cu sockets etc

24- Prepairing Drawing and completion report for KSEB incl. liasioning with office, submission & followup of application etc.

25- Supply & providing electrical grade rubber floor mats

26- Supply & providing cautin boards,Aluminium 105x105mm

27- Supply & providing electrical shock treatment chart (Three Languages - Hindi-English-Malayalam )

28- Supply & providing First Aid Kit

III - TELEPHONE Supply and wiring using 2 pair telephone cable in 20/25mm medium duty ISI PVC pipe with all necessary pvc accessories (a)2 pair telephone cabling

(b)Supply and fixing of RJ 11 type telephone socket on suitable PVC / metal boxes. (i)Telephone socket – single modular type

(ii)Telephone socket – double modular type

(c )Supply, laying commissioning of 0.5 sq.mm 10 pair armoured telephone cable with all accessories

(d)Supply and installation of KRONE connector telephone junction box of 20 pair.

IV - NETWORKING 1 -Supply & drawing of CAT-6 UTP 4pair network cable in suitable size heavy duty PVC conduit and conduct accessories (maximum 2runs of cable in 20mm PVC pipe. Maximum 4runs of cable in 25mm PVC pipe) (a) CAT-6 UTP 4pair network cabling Excluding the cost of pvc pipe and accessories

2- PVC CONDUIT LAYING Supply & laying of 20/25mm medium duty ISI PVC pipe with all necessary pvc accessories excluding the cost of circuit (a) 20mm ISI (M)

(b) 25mm ISI (M)

3- Supply & fixing of single I/O Box with face plate and connections

4- Supply & fixing of 24port Patch panel.The rate inclusive of terminations and interconnections.

5- Supply and fixing 9U rack of (APW or NETRECK) make with 5 power strip.The rack shall have ventilation fans & locking arrangements.

6- Supply and providing patch chord with CAT 6 UTP 4pair cable min. 1m length.

7- Supply and providing patch chord with CAT 6 UTP 4pair cable min. 2m length.

ATM Work :- ATM DB - Supplyandinstallationchargesof3phase4way(8+12) DBenclosurewithbusbars,neutrallinkearthbusand din rail suitable for fixing 4P MCB AND RCCB as incomer and SP MCBasoutgoingsIP43including copper /brass bus bar, neutral link, earth bus and DIN railsuitable forfixingMCBetc.fixedonwallusingsuitable anchor bolts or fixed in recess -includingcuttingholeonthewall,makinggoodthe damages,colourwashingetc.asrequired.

Incomer :- 40A(30mA)4PRCBOconformingtoIEC/EN61009 2010

Outgoings :- Supplyingandfitting6ASP240V50HzMCB10kAC curve conforming to IS/IEC 60898 -1 2002.

Supplyingandfitting16/20ASP240V50HzMCB 10kA C curve conforming to IS/IEC 60898 -12002.

ATM UPS DB :- SupplyandinstallationchargesofSingle phase 8 way(I/C+O/G)DBenclosurewithbusbars,neutrallink earthbusanddinrail suitable for fixing 2P ISOLATORas incomer andSPMCBasoutgoings IP43including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/isolator etc. fixed on wall using suitable anchor bolts orfixedin recessincludingcuttingholeon the wall , makinggood the damages, colour washingetc.asrequired.

Incomer : - 25A2PHIRCBO(30mA)-conformingtoIEC/EN 610092010

Out goings :-Supplyingandfitting6/16ASP240V50HzMCB 10kACcurveconformingtoIS/IEC60898-12002.

UPSOUTPUT:-SITC32ADPMCBinmetallic enclosure

AUTOMATICCHANGEOVERWITHCURRENT LIMITER(ACCL):SupplyandInstallationof25A ACCL SPN for ATM UPS

Supply& laying of 4 x 10sq. mm XLPE insulated PVC inner sheathed aluminium conductor, 1.1 kV grade armouredcableconformingtoIS:7098,asperapproved makeinground/trench/surface/pipefromVDBtoATM DB

CABLETERMINATIONSupplyandinstallation(SITC) of End termination of the following size of cables using flange type cable glands and heavy duty tinned aluminiumcrimpingtypecablesocketsincludinggland earthing4x10sq.mmcable.

Supply&layingof2x6sq.mmstrandedPVCinsulated coperwirethrough20mmRigidPVCconduit.

SITC of all materials and wiring forlight and exhaust fan points using colour coded 1.5 sq.mm 1100V grade, FRLS, PVC insulated stranded copper conductor single core stranded wires of IS 694 specification and should haveISmarking,throughISImediumgrade20mmrigid PVC conduits concealed in wall / slab/ceiling etc, completewithnecessaryaccessories,includingsupplying and fixing 6A modular type switch housed in a suitable factory made M. S box with moulded front plate including earthing the box, ceiling rose, connectors etc ...foronelightcontrolledbyoneswitch

sameasabovebutfortwolightscontrolledbyoneswitch sameasabovebutforfourlightscontrolledbyone switch

Supplying all materials and wiring for 6A plug points in independent positions using 1.5 sq.mm 1100V, FRLS PVC insulated copper conductor single core stranded wire for phase & neutral and earthing with 1 run of 1.5 sq.mm green copper wire inside the conduit / flat conduit, and fixing 6A modular type plug socket (2 in 1) controlledby6Aswitchwithmouldedfrontplate,housed in a suitable factory-built MS box.Giving connections, earthingetccompleteasrequired.

Supplying all materials and fixing modular type 16A power plug pointwith 16A 3 pin modular type plug socket controlled with16A switch withmoulded front plate, housed in a suitable factory builtMS/PVC box using2runsof2.5sq.mm1100V,FRLSPVCinsulated stranded Copper conductor includingearthingwith1run of 2.5 sq.mm green copper wirecontinuous run thorough 25 mm PVC conduit as per IS, giving inter connection etc complete as required and as directed by engineerincharge.asperIS,givinginterconnectionetc complete as required. Rate shall be for the Rate shall be fortheaveragelengthfromDBtotheswitchboard.No claim for additional wire and conduit.

Supplying all materials and fixing modular type 20 A powerplugpointwith20A3pinsocketcontrolledwith 20 A SP modular switchwith moulded front plate, housedina suitablefactorybuilt MSboxusing4sqmm 1100V,FRLSPVCinsulatedstrandedCopper conductor and earthing with 4 sqmm green Cu wire continuouslyrunthrough25mmPVCconduitasperIS giving inter connection etc complete as required.(AC point) the switch shall be fixed at a height of 120 cm from finished floor level .Rate shall be for the average length from DB to the switch board. No claim for additionalwireandconduit.

36W LED FITTING - Supply and Installation of 2'x2' squareLEDceilingflushmountedfittingofWipro,Elate LED,CRCO10

SITCof4KVA,Vguardmakevoltagestabilizer - - Supplyandfixing20ApigsocketwithplugtopforAC Stabilizer

ROUNDLEDFITTINGSupplyandInstallationof LEDceilingfittingWiproIrisLEDSlimRo,LD80-530- XXX-60-XX 1x9w or equivalent

ROUNDLEDDOWNLIGHTFITTINGSupplyand InstallationofLEDceilingfittingWiproIrisLEDSlim Ro, LD80-171-XXX-60-XX 1x18W

ROUNDLEDSPOTTILTFITTINGSupplyand Installation of 3W TILT LEDceilingfittingsPhilips 3W ASTRA Spot light or equivalent Supply and installation of plate earthing station conforming to IS 3043 using 600x600x3mm Copperplateearthelectrodeburiedinground,20mmdia3mlong perforated GI pipe with funnel and constructing inspectionchamber bymasonryworkwithheavy dutyCI inspectioncoverincludingcivilworkcompleteforUPS.

EARTHBENCHSupplyandfixingtinnedcopperearth bench (minimum 40cm length) 25x3 mm with all terminationusingcusocketsetc

Supply and laying of 1x8 SWG bare copper earthing conductorsincludingtermination,bracingthejointsetc. asperstandards-fromUPS-toearthbench-tocopper plateearth

Supplyandlayingof2x10SWGbarecopperearthing conductorsincludingtermination,bracingthejointsetc. as per standards along power cable

Supplying all materials, wiring forboard lightpoint controlled by 10A ELCB using 2 runs 4 sqmm 1100V FRLSPVCinsulatedCoperconductorandearthingwith 4 sqmm pvc insulated green Copper wire continuously run through 25 mm PVC conduit as per IS giving inter connectionetccompleteasrequired.Rateshallbeforthe average lenghth from DB to the board light. No claim for additional wire conduit.(Board Light point for ATM)

HARIDAS A A (BID ID -2409098)

SABROS DECOR SYSTEMS PVT. LTD. (BID ID -2400194)

GLOBAL INTRIOR WORKS AND TRADERS (BID ID -2415993)