Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | l1₹9.1 LAccepted-AOC | ₹9.1 L | l1 | Accepted-AOC lowest one |
| 2 | l2₹9.2 LRejected-Finance VPO BAGGA TEHSIL JAWALI DISTRICT KANGRA | KANGRA | HIMACHAL PRADESH | 176001 | ₹9.2 L | l2 | Rejected-Finance Rejected (highest) |
| 3 | l3₹10.0 LRejected-Finance VPO BHAPOO TEHSIL INDORA DISTT KANGRA H P | KANGRA | HIMACHAL PRADESH | 175013 | ₹10.0 L | l3 | Rejected-Finance Rejected (highest) |
| 4 | l4₹10.0 LRejected-Finance HAMIRPUR ROAD NEAR BUS STAND UNA DISTT UNA HP | UNA | HIMACHAL PRADESH | 174301 | ₹10.0 L | l4 | Rejected-Finance Rejected (highest) |
| 5 | l5₹10.1 LRejected-Finance GROUND FLOOR THAKUR COMPLEX BASANTPUR | BASANTPUR | SHIMLA | HIMACHAL PRADESH | 171018 | ₹10.1 L | l5 | Rejected-Finance Rejected (highest) |
| Sl No | Description | Qty | Unit | SS ENGINEERING WORKS L4 | SANJEEV SINGH L1 | Parvinder Kumar Govt. Contractor L3 | Rakesh Kumar L5 | Sachin Katoch Govt Contractor L2 |
|---|---|---|---|---|---|---|---|---|
| 1.00 | Pumping Machinery Tubwell Paniala :- Supply of submersible pumping set of Kirloskar/Kilburn/Clama/Crompton/KSB /BS make conforming to BIS; 8034-1976 latest suitable for lifting clean water (latest with uptodate ammendments) fitted with bronze impellers/suitable alloy directly coupled to squirrell case electric induction motor of same make as (manufacturer standard) conforming to BIS; 9283-1979 (latest with uptodate ammendments) and totally water proof for submersible duty, isolated from the pump by intermediate casing with double mechanical seal in oil chamber, grease packed lubricated bearings & provided with stainless steel thrust bearing plate to with stand vertical loads with minimum wear & tear. It should also be fitted with a device to take up expansion of water with the heating of motor including water level guard,errection clamps,cable clips & depth gauge etc. The pump shall be suitable for operation on data given below:- | 1 | P/set | 1,45,000 ₹1.4 L | 2,10,000 ₹2.1 L | 2,25,000 ₹2.3 L | 1,50,000 ₹1.5 L | 1,80,000 ₹1.8 L |
| 1.01iTotal Head 120.82 Mtrs | ||||||||
| 1.02ii Discharge required from each pump. 12.58 LPS | ||||||||
| 1.03iii No. of pump required 1.00 Nos. | ||||||||
| 1.04iv Location of the site of installation of machinery. The site is located at a distance of 10 KM from Kandarori Railway station. | ||||||||
| 1.05v The Altitude of installation. | ||||||||
| 1.06vi Type of current. | ||||||||
| 1.07vii Rate Voltage 415+ 10% | ||||||||
| 1.08viii Type of water and its source Tubewell Paniala | ||||||||
| 1.09ix Charactristics of water. - | ||||||||
Tender Value
₹12.1 L
EMD Value
₹24,125
Closing Date
25 Jul 2025, 11:00 amClosed
EXECUTIVE ENGINEER
EE JSV Division Indora
Laying, Jointing, Testing of G.I. pipe 150mm dia MC rising main providing and installation of submersible pumping machinery along with allied accessories Tube well Paniala CM announcement
2025_HPIPH_110140_1
EE-JSV-IND-2844-90 dated 15-07-2025
Open Tender
Civil Works
Indora
Please refer Tender documents.
9 documents required · 9 mandatory
₹500
₹24,125
29 Dec 2025
15 Jul 2025
25 Jul 2025
15 Jul 2025
25 Jul 2025
15 Jul 2025
Amount
Pumping Machinery Tubwell Paniala :- Supply of submersible pumping set of Kirloskar/Kilburn/Clama/Crompton/KSB /BS make conforming to BIS; 8034-1976 latest suitable for lifting clean water (latest with uptodate ammendments) fitted with bronze impellers/suitable alloy directly coupled to squirrell case electric induction motor of same make as (manufacturer standard) conforming to BIS; 9283-1979 (latest with uptodate ammendments) and totally water proof for submersible duty, isolated from the pump by intermediate casing with double mechanical seal in oil chamber, grease packed lubricated bearings & provided with stainless steel thrust bearing plate to with stand vertical loads with minimum wear & tear. It should also be fitted with a device to take up expansion of water with the heating of motor including water level guard,errection clamps,cable clips & depth gauge etc. The pump shall be suitable for operation on data given below:-
iTotal Head 120.82 Mtrs
ii Discharge required from each pump. 12.58 LPS
iii No. of pump required 1.00 Nos.
iv Location of the site of installation of machinery. The site is located at a distance of 10 KM from Kandarori Railway station.
v The Altitude of installation.
vi Type of current.
vii Rate Voltage 415+ 10%
viii Type of water and its source Tubewell Paniala
ix Charactristics of water. -
a)Ambient Temperature dig.c 20 dig. C
b)Turbidity NTU 113NTU
c)Hardness260Mg/Ltrs(as CaCO3) 540 Mg/ltr
d) PH 6.5 to 8.5
e) TDS 540 PPM
f)Other -
x Depth ofTUbe Well 140 mtrs
xi LWL in Tube Well 235.04 mtr
xii Center line level of Pump shaft 235.04 mtrs.
xiii Discharge level of highest point 344.00 mtrs.
xiv Total head in Mtrs 120.82 mtrs.
xv Length of R/Main 1050 mtrs.
xvi Dia of Rising main 150 mm dia GI pipe 4.80 mm thick (MC)
xvii No of working hours per day 20 Hours
xviii Limit of pump operation. (-) 15 % (+) 10% of total head
xix R.P.M. of pumping set. 2900 RPM
xx Test run. 8 Hours continueously for 7 days
Supply , Installation, Testing and Commissioning of Fully Automatic LT Panel for Submersible pump made out of 16 Gauge sheet powder coated dust and veremin proof wall mounted and front opering door type switch board with copper insulated wiring suitable to operate 1 No. pump of rating 40 HP automatically through Variable Frequency Drive Starter. Starter should be capable to handle all the faults like short circuit, over current, under current, over voltage, under voltage, dry pump protection. It should get on and off command automatically from PLC and HMI. Monitoring and controlling of Pump running and tripping status should be monitored and controlled remotely through IOT enabled device. Access should be given to 3 users. Make : Aarmation Electric private Limited / MAS/ELLES complete in all respects within all leads and lifts as per directions and to the entire satisfaction of engineer in charge
Providing and fixing of Kirloskar/ Kilburn/Leader make Cast iron double flanged swing check type reflux valve of class PN 1.6 having bye pass arrangement ( to be provided on delivery side) of size of one size higher than the delivery size of pump and shall be suitable for withstanding nominal seat presure of 16.32 Kg/Cm2 confirming to BIS 5312-1984 Part-I .(The size & class of valve shall be specified by the tenderer)
Providing & laying PVC insulated jointless, flat water proof copper cable of Siemens/Finolex/ Grandlay/ Gloster make conforming to BIS:1554 (Part I) -1988 or latest with up to date ammendments of suitable size for the pump sets offered(one cable carrying all three phases) including all other electrical equipment /accessories such as thimbles ,flexible pipe, solder, nuts & bolts cable glands etc. laid in pipes or trenches under floor. The type,size & make will be subject to approval of HPSEB authorities.In case of non acceptance by HPSEB authorities it shall have to be replaced by the tenderer free of cost.
On supply side of 3½ core coper cable 16 mm^2 ( From HPSEB Meter to Switch & Starter).
On motor side 3 core flat joint less copper cable of size10 mm^2 ( From Switch & Starter to Motor) pump installed in the bore.
Supply of standarad make 100 mm dia circular/square dial pressure gauge of suitable range Fiebeg/Bourden/ Precision make with all accessories such as stop cock,copper tubing etc. conforming to BIS 3624-1987 latest with up to date ammendments.
Providing Laying of G.I./MSERW pipe considering site requirements and having appropriate size in accordance with the delivery size of pumping set . The pipe shall conform to relevant BIS codes & capable of with standing the feild test pressure equal to 1.5 times the operating pressure including all type of fittings such as bends, tapers/ reducers, flanges, rubber gaskets 3mmthick, nuts & bolts and any other fitting required at site and work shall be to the entire satisfaction of Engineer-in-Charge. The pipe material shall conform to relevant BIS Code and capable of with standing FTP equal to 1.5 times the operating pressure the complete arrangement shall compromise of
Delivery Pipe/column assembly 125mm dia G.I. medium class (size to be specified by the tenderer).
P/L double loop earthing with copper plate 600x600x3mm thick electrode and copper strip of 25x3 complete including providing of material such as charcoal, common salt, GI pipes, thimbles, nuts & bolts, digging of pits, copper / GI wire /strips of required capacity conforming to BIS8034-1978 latest with upto date ammendments for above motor & other electrical equipments including all civil works
Errection of all equipments including cost of tees, bends tapers & any other fittings required as per site conditions & as per directions of Engineer-in-Charge.
Rising main:- Excavation in foundation trenches (for Pipes & Pits) upto all depths in all classification of earth work such as pick work, jumper work, saturated soil including bailing or pumping out water, blasting soft /hard rock or chieselling soft /hard rock where blasting is prohibited in all lifts including trimming & dressing of sides leveling of beds to correct grade including shoring/strutting planking, timbering & dewatering wherever required stacking the serviceable and unserviceable material / soil separately and after laying, jointing and testing of pipes, returning the unserviceable soil in trenches in 15cm ( Fifteen centimeter) layers including consolidating of such deposited layer by ramming and watering & then disposing of all surplus excavated soil/ unserviceable material as directed within all leads and lifts including restoration of un-metalled surface to its original condition and including cost of diversion for traffic, night signals, fixing caution boards, crossing over trenches for access to houses, fencing etc. complete in all respect with in all leads and lifts as per directions of Engineer-in-Charge.
Laying, jointing & testing in trenches to be levelled to grade, BIS marked G.I. pipe 150mm dia plain ended (Medium class) duly flanged after 100 mtrs. pipe with intermediate butt welded joints including the cost of bends/short pieces made from parent tubes of diferent degrees cutting welding and jointing with flanges conforming to tables as specified below of BIS: 6392 -1971 (latest with upto date ammendments) welded at both ends as per BIS:814 (latest with upto date ammendments) with electrodes confirming to BIS 814 (latest with upto date ammendments) & provided with nuts and bolts BIS: 1369 (latest with upto date ammendments) of required sizes, 4 mm thick champion make compressed asbestos fiber gasket or synthetic rubber gasket confirming to BIS:2712 (latest with upto date ammendments) & approved specifications as per site conditions including flushing, cleaning & hydraulic testing complete to the best satisfaction of Engineer-in-Charge. ( the cost of MS flanges and rubber gasket will be measured & paid for separately)
150mm dia G.I. pipe (M) 4.80mm thick
Providing,welding & fixing of MS flanges to confirming to IS 6392-1971(Latest with upto date amendments) of flange table with MS tubes in Two layer o n outer face & one inner face to make the joint leak proof.The thockness of gasket not less then 3.00 mm confirming to IS 2712-1965 complete in all respect and to the best satisfaction and direction of Engineer-in-Charge with in all leads and lifts.Flange t be welded after 100 mtr interval of pipe(The cost of laying of pipe with butt weldingt will be measured & paid for separately)
150mm dia Flanged Table-5
Sachin Katoch Govt Contractor (BID ID -538288)
Parvinder Kumar Govt. Contractor (BID ID -537770)
SS ENGINEERING WORKS (BID ID -538084)
Rakesh Kumar (BID ID -538212)
stage.html
html • 0.05 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid