LAC-ADS-Construction of Taluk hospital Konni Phase-2-work-Electrical Lift Work-1- SITC of 1No. Hospital lift

OD208463/2022-2023:Supply, installation and commissioning of 15 passenger /1020kg Bed cum passenger lift with the following specification: 1. Type of Lift - Bed cum passenger lift, Load / Persons -1020 Kg / 15 persons, With Machine Room type 2. Rated speed 1 M/Sec. 3. Travel ? Approximately 19.5 Meter 4. No. of floor and entrance served -6 (Base + Ground + 4 upper floors) 5. Method of control - With/without attendant, 6. Position of machine - Top of lift well, 7. Size of lift well - 1800mm W x 3000 mm D, 8. Size of car - As per IS 9. Drive - micro processor based Variable voltage variable frequency, Operation with ARD - Simplex full selective, collective control with ON/OFF switch, 10. Construction of design and furnishing of car body work ? Vandal proof stainless steel (SS304 Jindal/Tata make) finish cabinet with scratch proof stainless steel door (sheet 1mm thickness), stainless steel mirror finish ceiling, 3mm minimum thickness aluminium anti-skid flooring, fan with timer cut off, push to talk, LED display, LED light, hand rails and floor announcement system. 11. All buttons in car and all landings should have Braille sign 12. Landing entrance - Automatic centre opening Vandal proof stainless steel sliding door as per IS with provision for emergency mechanical opening key and half framed fire rated glass door for minimum 2 Hr. 13. Call and position indicator - Up/down direction & position LED/LCD indication shall be provided at all landings 14. Electric supply - Light 230V, 50Hz single phase 2 wire system. 15. Power 415V 50Hz 3 phase 4 wire system 16. Infra-red door opening system -To be provided for entire length of the door, 17. Automatic Rescue Device - Provide automatic rescue device with an electronic controller powered by maintenance free batteries with capacity for minimum four rescue operation. The rescue operation should work within 10 seconds of power failure. 18. Indication in the car - a) Car position, b) Call indicator, c) Door close/open push button, d) Emergency stop button, e) Flush mounted switch for fan (with timer) and light, f) Non-stop button g) Battery operated emergency lamp with rechargeable batteries, h) Intercom wiring with one master unit with 2 slaves. I) Battery operated alaram bell J) Fireman.s switch at main lobby, 19. Winding handle - Manual winding handle for use in emergency 20. Safeties - a) Over speed governor operated safety gear, b) Buffers, c) Motor over load protection, d) Phase reversal protection, e) Other safeties as per ISS, f) Single phase preventer, g) Final limit switch, 21. Leveling - Automatic leveling at all landing as per IS 22. Guarantee - Company shall carry out free maintenance during warranty period from the date of handing over and includes, a) Cleaning lift equipment, b) Lubrication of all moving parts, c) Replacing of lubricating oil when required, d) Checking and adjusting contacts, e) Replacing fusible item, alarm etc. f) Recharging batteries in case of drain/ renewing batteries, g) Replacing /rewinding of all defective parts of the lift including motors and V3F unit. 23. Control panel - Control panel will be dust and vermin proof of sheet metal enclosure 24. Announcement System - To provide lift announcement system and music system. 25. Approval - Preparing drawings and obtaining scheme approval as well as energisation certificate from concerned electrical Inspectorate incuding preparation of necessary drawing for the same. Necessary fees shall be remitted to the inspectorate by the firm for which no refund shall be will be made from department including taking insurance for one year 26. Tests - At site test as per IS to be carried out before Handing over . 27. Training to client for emergency rescue operation and normal operations. 28. Submission of O&M manual, troubleshooting guide and guarantee/ warranty certificates. First year insurance also to be arranged. 30. Scope of work- a)supply of materials b)Minor civil works such as removal of temporary brick work in the lift entrance without affecting the building structure .Finishing/altering civil works in the lift entrance/pit by providing brick work & plastering if necessary including construction of buffer block ,cutting pockets and grounding brackets for the guide rails , grouting boxes for control units , correction of wall opening in the front side of the wall by additional brick work or cutting existing brick work core cutting for drawing ropes, etc. C)Scaffolding d) door Frames e)Supporting Steel f) Temporary electric supply for the installation of lift .Electric Supply for testing and commissioning of lift is to be arranged by the firm on their own account