Rate Contract for Supply and Installation of Open Gym Green Gym Equipments in Municipal Corporation of Delhi

RATE CONTRACT FOR SUPPLY & INSTALLATION OF OPEN GYM (GREEN GYM) EQUIPMENTS IN MUNICIPAL CORPORATION OF DELHI

SEATED PULLER /PULL CHAIR MADE FROM “C” CLASS G.I PIPE. DIMENSIONS: - 1900MM (LENGTH) X 740MM (WIDTH) X 1920MM. (HEIGHT). SAFE AREA:- 1.2MTR X 3MTR. SEATED PULLER EQUIPMENT MADE UP OF “C” CLASS G.I. PIPE OF DIFFERENT NB.NB STANDS FOR NOMINAL BORE SIZES I.E. INTERNAL DIAMETER OF PIPE IN MILLIMETERS. THE CENTER PIPE IS OF 100NB MADE FROM “C” CLASS G.I. PIPE. BOTTOM SUPPORT IS OF M.S. ROUND PLATE OF DIA 250 MM & 10MM THICKNESS WELDED. ALL LINKAGES ARE MADE UP OF 25NB “C” CLASS G.I. PIPE. THE HANDLE FRAME IS OF 32NB “C” CLASS G.I. PIPE. THE SEAT FRAME IS OF 32NB “C” CLASS G.I. PIPE. TO BUILD STRUCTURE BUSHES ARE USED WHICH ARE MADE FROM SEAMLESS PIPE OF 60MM O.D. AND 5MM THICKNESS AS WELL AS 60MM DIAMETER SOLID BAR BUSH USED. THE FOUNDATION USED FOR FIXING IS A STRUCTURE AND MADE FROM CENTER PIPE OF G.I. OF 80 NB “C” CLASS. WELDED WITH M.S. ROUND PLATE OF DIA 250 MM & 10MM THICK. MAIN PIPE SUPPORTED WITH 25 MM X 25MM M.S. ANGLES OF 3 MM THICKNESS AND 20MM X 40MM CRC SQUARE PIPES OF 3MM THICKNESS. FOUNDATION COVER CLOSING CAP IS MADE FROM INJECTION MOULDED PLASTIC LLDPE / HDPE. THE SEATS AND BACK RESTS ARE FITTED ON THE OUTER FRAMES ARE MADE UP OF M.S. SHEET OF SIZE 330 MM X 300 MMX2MM THICKNESS AND DEEP DRAWN AND PRESSED IN TOOLS AND DIES TO HAVE UNIFORM RADIUS OF 20 MM WITH NO SHARP EDGES.CLOSING CAPS ARE MADE UP OF FROM INJECTION MOULDED PLASTIC LLDPE / HDPE.PINS USED OF DIAMETER 25MM AND 17MM ARE MADE UP FROM SAE 8620 BRIGHT MATERIAL. THE BEARINGS USED ARE OF “6205 2RS1” AND “6203 2RS1” PERMANENT LUBRICATED SEALED BEARING OF REPUTED BRAND.HIGH TENSILE STEEL WITH GALVANIZED NUTS & BOLTS ARE USED FOR ASSEMBLY.THECIRCLIPS USED FOR ASSEMBLY ARE OF A16. THE GYM EQUIPMENT SHALL BE FINISHED SMOOTH WITH A PRIMER COATING OF ATLEAST 40 MICRON FOLLOWED BY EPOXY BASED POWDER COATING WITH POLYSTER POWDER COATING OF AT LEAST 60 TO 70 MICRON THICKNESS USING EXONOBEL / BERGER MAKE PAINTS OR ITS EQUIVALENT PAINTS. THE HOLDING DOWN/FIXING OF GYM EQUIPMENTS SHALL BE EMBODED IN CEMENT CONCRETE IN THE RATIO OF 1:2:4 (1CEMENT : 2 COARSE SAND :4 STONE AGG. 20MM NOMINAL SIZE)

CROSS TRAINER /ELLIPTICAL EXERCISER:- DIMENSIONS: - 1320MM (LENGTH) X 600MM (WIDTH) X 1750MM. (HEIGHT). SAFE AREA: - 1.77 X 1.2MTR. CROSS TRAINER EQUIPMENT MADE FROM “C” CLASS G.I. PIPE OF DIFFERENT NB.NB STANDS FOR NOMINAL BORE SIZES I.E. INTERNAL DIAMETER OF PIPE IN MILLIMETERS. THE MAIN FRAME PIPES ARE OF 80NB “C” CLASS G.I. PIPE WITH SINGLE BEND PIPE WITH 250MM RADIUS. THE BOTTOM SUPPORT OF M.S. ROUND PLATE OF DIA 250 MM & 10MM THICK. THE HANDLE FRAME IS MADE UP OF 25NB “C” CLASS G.I. PIPE. THE FOUNDATION USED FOR FIXING IS A STRUCTURE AND MADE FROM CENTER PIPE OF G.I. OF 80 NB “C” CLASS WELDED WITH M.S. ROUND PLATE OF DIA 250 MM & 10MM THICK. MAIN PIPE SUPPORTED WITH 25 MM X 25MM M.S. ANGLES OF 3 MM THICKNESS AND 20MM X 40MM CRC SQUARE PIPES OF 3MM THICKNESS. TO BUILD STRUCTURE BUSHES ARE USED WHICH ARE MADE FROM M.S. SEAMLESS PIPE OF 60MM OD WITH 5 MM THICKNESS. THE FOOTRESTS ARE MADE FROM INJECTION MOULDED PLASTIC LLDPE / HDPE. CLOSING CAPS ARE MADE UP OF INJECTION MOULDED PLASTIC LLDPE / HDPE. PINS USED OF DIAMETER 35MM, 25MM, AND 17MM ARE MADE UP FROM SAE 8620 BRIGHT .THE BEARINGS USED ARE OF “6007 2RS1” “62052RS1” AND “62032RS1” PERMANENT LUBRICATED SEALED BEARING OF REPUTED BRAND. HIGH TENSILE STEEL WITH GALVANIZED NUTS AND BOLTS ARE USED FOR ASSEMBLY. THE GYM EQUIPMENT SHALL BE FINISHED SMOOTH WITH A PRIMER COATING OF ATLEAST 40 MICRON FOLLOWED BY EPOXY BASED POWDER COATING WITH POLYSTER POWDER COATING OF AT LEAST 60 TO 70 MICRON THICKNESS USING EXONOBEL / BERGER MAKE PAINTS OR ITS EQUIVALENT PAINTS. THE HOLDING DOWN/FIXING OF GYM EQUIPMENTS SHALL BE EMBODED IN CEMENT CONCRETE IN THE RATIO OF 1:2:4 (1CEMENT : 2 COARSE SAND :4 STONE AGG. 20MM NOMINAL SIZE). A16 , A 24 MM CIRCLIPS ARE USED FOR ASSEMBLY. BOLT M8X16 MM AND NY LOCK NUT OF M8 MADE OF SS304 USED ON NYLON CAP MOUNTED ON PINS TO PROTECT BEARINGS AND PINS FROM RAIN AND DUST.

BACK EXTENSION DIMENSIONS: - 1400MM (LENGTH) X 700MM (WIDTH) X 820MM (HEIGHT). SAFE AREA: - 2.4MTR X 1.7MTR. BACK EXTENSION EQUIPMENT MADE FROM “C” CLASS G.I. PIPE OF DIFFERENT NB PIPE. (NB STANDS FOR NOMINAL BORE I.E. INTERNAL DIAMETER OF PIPE IN MM) THE MAIN FRAME IS OF 50MM NB MADE FROM “C” CLASS G.I. PIPE. THE FOOT RESTING FRAME OF 32MM NB MADE FROM ”C” CLASS G.I. PIPE. THE HANDLE FRAME IS OF 25NB MADE FROM “C” CLASS G.I. PIPE. THE SEAT FITTED ON THE OUTER FRAMES IS MADE UP OF M.S. SHEET OF SIZE 330 MM X 300MMX2MM THICKNESS AND DEEP DRAWN AND PRESSED IN TOOLS AND DIES TO HAVE UNIFORM RADIUS OF 20 MM WITH NO SHARP EDGES. THE FOUNDATION USED FOR FIXING IS CONSISTS OF 50MM NB MADE FROM ”C” CLASS G.I. PIPE.THE FOOTRESTS ARE MADE FROM INJECTION MOULDED PLASTIC LLDPE / HDPE. THE GYM EQUIPMENT SHALL BE FINISHED SMOOTH WITH A PRIMER COATING OF ATLEAST 40 MICRON FOLLOWED BY EPOXY BASED POWDER COATING WITH POLYSTER POWDER COATING OF AT LEAST 60 TO 70 MICRON THICKNESS USING EXONOBEL / BERGER MAKE PAINTS OR ITS EQUIVALENT PAINTS. THE HOLDING DOWN/FIXING OF GYM EQUIPMENTS SHALL BE EMBODED IN CEMENT CONCRETE IN THE RATIO OF 1:2:4 (1CEMENT : 2 COARSE SAND :4 STONE AGG. 20MM NOMINAL SIZE).

SIT UP BOARD FOR USE OF TWO PERSONS AT ONE TIME. DIMENSIONS: - 1820MM (LENGTH) X 430MM (WIDTH) X 580MM (HEIGHT). SAFE AREA:- 2.8MTR X 0.6MTR. SIT UP BOARD EQUIPMENT MADE FROM “C” CLASS G.I. PIPE OF DIFFERENT NB.NB STANDS FOR NOMINAL BORE SIZES I.E. INTERNAL DIAMETER OF PIPE IN MILLIMETERS. THE MAIN FRAME IS OF 50MM NB MADE FROM “C” CLASS G.I. PIPE IN A SINGLE BEND AND SUPPORTED WITH THE MS ROUND PLATE OF DIA 250X10MM THICKNESS. FIBER REINFORCED PLASTIC SHEET OF 3MM THICKNESS IS BOUNDED ON 25MM NB (G.I.) “C” CLASS PIPE OF MAIN FRAME. THE BASE SUPPORT OF THE SIT UP BOARD IS MADE 40NB (G.I.) “C” CLASS PIPE. THE FOUNDATION USED FOR FIXING IS A STRUCTURE AND MADE FROM CENTER PIPE OF G.I. OF 80 NB “C” CLASS WELDED WITH M.S. ROUND PLATE OF DIA 250 MM & 10MM THICK. MAIN PIPE SUPPORTED WITH 25 MM X 25MM M.S. ANGLES OF 3 MM THICKNESS AND 20MM X 40MM CRC SQUARE PIPES OF 3MM THICKNESS. THE GYM EQUIPMENT SHALL BE FINISHED SMOOTH WITH A PRIMER COATING OF ATLEAST 40 MICRON FOLLOWED BY EPOXY BASED POWDER COATING WITH POLYSTER POWDER COATING OF AT LEAST 60 TO 70 MICRON THICKNESS USING EXONOBEL / BERGER MAKE PAINTS OR ITS EQUIVALENT PAINTS. THE HOLDING DOWN/FIXING OF GYM EQUIPMENTS SHALL BE EMBODED IN CEMENT CONCRETE IN THE RATIO OF 1:2:4 (1CEMENT : 2 COARSE SAND :4 STONE AGG. 20MM NOMINAL SIZE)

STANDING SEATING TWISTER. DIMENSIONS: - 1700MM (LENGTH) X 540MM (WIDTH) X 1250MM. (HEIGHT). SAFE AREA: - 3 MTR X 1MTR. SEATING & STANDING TWISTER EQUIPMENT MADE FROM “C” CLASS G.I. PIPE OF DIFFERENT NB. NB STANDS FOR NOMINAL BORE SIZES I.E. INTERNAL DIAMETER OF PIPE IN MILLIMETERS. THE CENTER PIPE IS OF 100MM NB MADE FROM “C” CLASS G.I. ROUND PIPE. THE M.S. ROUND PLATE OF DIA 250 MM & 10MM THICKNESS IS WELDED AT BOTTOM. HANDLE AND BOTTOM SLEEVE PIPE OF 125MM OD WITH THICKNESS 5MM PROVIDED FOR EASY ASSEMBLY, REPLACEMENT AND MAINTENANCE. THE BOTTOM FRAME OF THE SEATING & STANDING TWISTER IS OF 32 NB, 50 NB, AND 25 NB MADE FROM “C” CLASS G.I. PIPE. THE HANDLE FRAME OF SEATING & STANDING TWISTER IS 25 NB & FOOT RESTING FRAME OF SEATING SIDE IS MADE FROM “C” CLASS G.I. PIPE OF 25MM NB.THE FOUNDATION USED FOR FIXING IS A STRUCTURE AND MADE FROM CENTER PIPE OF G.I. OF 80 NB “C” CLASS, WELDED WITH M.S. ROUND PLATE OF DIA 250 MM & 10MM THICK. MAIN PIPE SUPPORTED WITH 25 MM X 25MM M.S. ANGLES OF 3 MM THICKNESS AND 20MM X 40MM CRCA SQUARE PIPES OF 3MM THICKNESS. THE TWISTER PLATE FITTED ON THE BOTTOM FRAME IS MADE UP OF INJECTION MOULDED PLASTIC LLDPE / HDPE AND SUPPORTED BY M.S. ROUND PLATE OF SIZE 300MM DIAMETER&10MM THICKNESS. CLOSING CAPS ARE MADE UP INJECTION MOULDED PLASTIC LLDPE / HDPE. THE PINS USED ARE MADE UP OF DIA 35 MM SAE 8620 BRIGHT MATERIAL. THE BEARINGS USED ARE OF “62052RS1” PERMANENT LUBRICATED SEALED BEARING OF REPUTED BRAND. HIGH TENSILE STEEL WITH GALVANIZED NUTS & BOLTS ARE USED FOR ASSEMBLY. THE GYM EQUIPMENT SHALL BE FINISHED SMOOTH WITH A PRIMER COATING OF ATLEAST 40 MICRON FOLLOWED BY EPOXY BASED POWDER COATING WITH POLYSTER POWDER COATING OF AT LEAST 60 TO 70 MICRON THICKNESS USING EXONOBEL / BERGER MAKE PAINTS OR ITS EQUIVALENT PAINTS. THE HOLDING DOWN/FIXING OF GYM EQUIPMENTS SHALL BE EMBODED IN CEMENT CONCRETE IN THE RATIO OF 1:2:4 (1CEMENT : 2 COARSE SAND :4 STONE AGG. 20MM NOMINAL SIZE)

SKY WALKER DIMENSIONS: - 1720MM (LENGTH) X 630MM (WIDTH) X 1750MM.(HEIGHT). SAFE AREA: - 2.7MTR X 1.6MTR. SKY WALKER EQUIPMENT MADE FROM “C” CLASS G.I. PIPE OF DIFFERENT NB.NB STANDS FOR NOMINAL BORE SIZES I.E. INTERNAL DIAMETER OF PIPE IN MILLIMETERS. THE MAIN FRAME PIPE IS OF 80MM NB MADE FROM “C” CLASS G.I. MATERIAL WHICH IS BEND AT THE RADIUS OF 250MM.THE LEG MOVEMENT FRAME IS OF 50 X 50MM X 3MM THICK CRC SQUARE PIPE. SLEEVES ARE MADE UP OF 100 MM OD M.S. PIPE WITH THICKNESS 5MM. THIS RESULTS IN EASY REPLACEMENT OF BEARINGS, PINS AND HANDLE THE HANDLE FRAME IS OF 25MM NB MADE FROM “C” CLASS G.I. PIPE. THE FOUNDATION USED FOR FIXING IS A STRUCTURE AND MADE FROM CENTER PIPE OF G.I. OF 80 NB “C” CLASS. WELDED WITH M.S. ROUND PLATE OF DIA 250 MM & 10MM THICK. MAIN PIPE SUPPORTED WITH 25 MM X 25MM M.S. ANGLES OF 3 MM THICKNESS AND 20MM X 40MM CRC SQUARE PIPES OF 3MM THICKNESS. TWO FOUNDATIONS ARE PROVIDED FOR RIGID SUPPORT. THE FOOTRESTS MADE FROM INJECTION MOULDED PLASTIC LLDPE / HDPE. CLOSING CAPS ARE MADE UP OF INJECTION MOULDED PLASTIC LLDPE / HDPE. THE PINS USED ARE MADE UP OF DIA 25MM SAE8620 BRIGHT MATERIAL. PINS ARE FIXED AT THE OUTER END WITH M8 GRUB SCREWS AND DIA.8MM SS BALL. THE BEARINGS USED ARE “62052RS1” ARE PERMANENT LUBRICATED SEALED BEARING OF REPUTED BRAND. HIGH TENSILE STEEL WITH GALVANIZED NUTS & BOLTS ARE USED FOR ASSEMBLY. THE CERCLIPS USED FOR ASSEMBLY ARE OF A24 TYPE. THE GYM EQUIPMENT SHALL BE FINISHED SMOOTH WITH A PRIMER COATING OF ATLEAST 40 MICRON FOLLOWED BY EPOXY BASED POWDER COATING WITH POLYSTER POWDER COATING OF AT LEAST 60 TO 70 MICRON THICKNESS USING EXONOBEL / BERGER MAKE PAINTS OR ITS EQUIVALENT PAINTS. THE HOLDING DOWN/FIXING OF GYM EQUIPMENTS SHALL BE EMBODED IN CEMENT CONCRETE IN THE RATIO OF 1:2:4 (1CEMENT : 2 COARSE SAND :4 STONE AGG. 20MM NOMINAL SIZE).

CHEST PRESS . DIMENSIONS: - 2000MM (LENGTH) X 710MM (WIDTH) X 2200MM. (HEIGHT). SAFE AREA: - 3.0MTR X 1.7MTR. CHEST PRESS EQUIPMENT MADE UP OF “C” CLASS G.I. PIPE OF DIFFERENT NB. NB STANDS FOR NOMINAL BORE SIZES I.E. INTERNAL DIAMETER OF PIPE IN MILLIMETERS. THE CENTER PIPE IS OF 100NB MADE UP OF “C” CLASS G.I. PIPE. THE BOTTOM WELDED WITH SUPPORT OF M.S. ROUND PLATE OF DIA 250 MM & 10MM THICKNESS. THE CONNECTING PIPES ARE MADE UP FROM 25NB “C” CLASS G.I. PIPE. THE HANDLE FRAME IS MADE UP FROM 32NB “C” CLASS G.I. PIPE. TO BUILD STRUCTURE BUSHES ARE USED WHICH ARE MADE FROM MS SEAMLESS PIPE OF 60MM O.D. AND 5MM THICKNESS AS WELL AS 60MM DIAMETER SOLID BAR BUSH IS USED. THE FOUNDATION USED FOR FIXING IS A STRUCTURE AND MADE FROM CENTER PIPE OF G.I. OF 80 NB “C” CLASS. WELDED WITH M.S. ROUND PLATE OF DIA 250 MM & 10MM THICK. MAIN PIPE SUPPORTED WITH 25 MM X 25MM M.S. ANGLES OF 3 MM THICKNESS AND 20MM X 40MM CRC SQUARE PIPES OF 3MM THICKNESS. THE SEATS AND BACK RESTS ARE FITTED ON THE OUTER FRAMES ARE MADE UP OF M.S. SHEET OF SIZE 330MM X 300 MMX2MM THICKNESS AND DEEP DRAWN AND PRESSED IN TOOLS AND DIES TO HAVE UNIFORM RADIUS OF 20 MM WITH NO SHARP EDGES. CLOSING CAPS ARE MADE UP OF INJECTION MOULDED PLASTIC LLDPE / HDPE. FOUNDATION COVER CLOSING CAP IS MADE FROM INJECTION MOULDED PLASTIC LLDPE / HDPE. PINS USED OF DIAMETER 25MM AND 17MM ARE MADE UP FROM SAE 8620 BRIGHT MATERIAL. BOLT M8X16 MM AND NYLOCK NUT OF M8 MADE OF SS 304 USED ON NYLON CAP MOUNTED ON PINS TO PROTECT BEARINGS AND PINS FROM RAIN AND DUST. THE BEARINGS USED ARE OF “62052RS1” &“62032RS1” PERMANENT LUBRICATED SEALED BEARING OF REPUTED BRAND. HIGH TENSILE STEEL WITH GALVANIZED NUTS & BOLTS ARE USED FOR ASSEMBLY. THE CER CLIPS USED FOR LOCKING IS MADE UP OF A24 MM & A16MM. THE GYM EQUIPMENT SHALL BE FINISHED SMOOTH WITH A PRIMER COATING OF ATLEAST 40 MICRON FOLLOWED BY EPOXY BASED POWDER COATING WITH POLYSTER POWDER COATING OF AT LEAST 60 TO 70 MICRON THICKNESS USING EXONOBEL / BERGER MAKE PAINTS OR ITS EQUIVALENT PAINTS. THE HOLDING DOWN/FIXING OF GYM EQUIPMENTS SHALL BE EMBODED IN CEMENT CONCRETE IN THE RATIO OF 1:2:4 (1CEMENT : 2 COARSE SAND :4 STONE AGG. 20MM NOMINAL SIZE).

HORSE RIDER DIMENSIONS: - 1180MM (LENGTH) X 400MM (WIDTH) X 1400MM. (HEIGHT). SAFE AREA: - 2.2MTR X 1.4MTR. HORSE RIDER EQUIPMENT MADE FROM “C” CLASS G.I. PIPE OF DIFFERENT NB.NB STANDS FOR NOMINAL BORE SIZES I.E. INTERNAL DIAMETER OF PIPE IN MILLIMETERS. THE MAIN FRAME OF 100NB MADE FROM “C” CLASS G.I. PIPES WELDED WITH M.S. ROUND PLATE OF DIA 250 MM & 10MM THICK. SEAT PROVIDED ARE MADE UP OF MS DEEP DRAW QUANTITY OF 2MM THICKNESS WITH NO JOINT WITH UNIFORM OUTER EDGE RADIUS 20MM. THE FOUNDATION USED FOR FIXING IS A STRUCTURE AND MADE FROM CENTER PIPE OF G.I. OF 80 NB “C” CLASS WELDED WITH M.S. ROUND PLATE OF DIA 250 MM & 10MM THICK. MAIN PIPE SUPPORTED WITH 25 MM X 25MM M.S. ANGLES OF 3 MM THICKNESS AND 20MM X 40MM CRC SQUARE PIPES OF 3MM THICKNESS. THE LEG MOVEMENT FRAME IS OF 32NB MADE FROM “C” G.I. PIPE. THE HANDLE FRAME IS OF 32 NB MADE FROM “C” CLASS G.I. PIPE. THE FOOTRESTS ARE MADE FROM 25 NB “C” CLASS G.I. PIPE. PINS USED OF DIAMETER 17 MM ARE MADE UP FROM SAE 8620 BRIGHT MATERIAL. N THE BEARINGS USED OF “62032RS1” PERMANENT LUBRICATED SEALED BEARING OF REPUTED BRAND. HIGH TENSILE STEEL WITH GALVANIZED NUTS & BOLTS FOR ASSEMBLY. THE SER CLIPS USED FOR ASSEMBLY ARE OF A24 MM. THE GYM EQUIPMENT SHALL BE FINISHED SMOOTH WITH A PRIMER COATING OF AT LEAST 40 MICRON FOLLOWED BY EPOXY BASED POWDER COATING WITH POLYSTER POWDER COATING OF AT LEAST 60 TO 70 MICRON THICKNESS USING EXONOBEL / BERGER MAKE PAINTS OR ITS EQUIVALENT PAINTS. THE HOLDING DOWN/FIXING OF GYM EQUIPMENTS SHALL BE EMBODED IN CEMENT CONCRETE IN THE RATIO OF 1:2:4 (1CEMENT : 2 COARSE SAND :4 STONE AGG. 20MM NOMINAL SIZE).

ROWER (DIMENSIONS: - 1200MM (LENGTH) X 1000MM (WIDTH) X 920MM. (HEIGHT). SAFE AREA: - 1.5MTR. X 1.5MTR. ROWER EQUIPMENT MADE FROM “C” CLASS G.I. PIPE OF DIFFERENT NB. NB STANDS FOR NOMINAL BORE SIZES I.E. INTERNAL DIAMETER OF PIPE IN MILI-METERS.THE MAIN FRAME IS OF 80NB “C” CLASS G.I. PIPE WELDED WITH M.S. ROUND PLATE OF 250MMX10MM. THE HANDLE FRAME 25NB IS MADE FROM “C” CLASS G.I. PIPE. THE FOUNDATION USED FOR FIXING IS A STRUCTURE AND MADE FROM CENTER PIPE OF G.I. OF 80 NB “C” CLASS WELDED WITH M.S. ROUND PLATE OF DIA 250 MM & 10MM THICK. MAIN PIPE SUPPORTED WITH 25 MM X 25MM M.S. ANGLES OF 3 MM THICKNESS AND 20MM X 40MM CRC SQUARE PIPES OF 3MM THICKNESS. TO JOIN THE MOVEMENT FRAME TO MAIN FRAME CONNECTING LINKS MADE UP FROM 32 NB G.I. “C” CLASS PIPE. THE SEAT FITTED ON THE OUTER FRAMES ARE MADE UP OF M.S. SHEET OF SIZE 330 MM X 300MMX2MM THICKNESS AND DEEP DRAWN AND PRESSED TOOLS AND DIES TO HAVE UNIFORM RADIUS OF 20 MM WITH NO SHARP EDGES. PINS USED OF DIAMETER 17MM ARE MADE UP FROM SAE 8620 BRIGHT MATERIAL. THE BEARINGS USED ARE OF “6203ZZ” PERMANENT LUBRICATED SEALED BEARING OF REPUTED BRAND. HIGH TENSILE STEEL WITH GALVANIZED NUTS AND BOLTS ARE USED FOR ASSEMBLY. THE P.U. BUSHES (STOPPER) USED TO AVOID THE COLLISION. THE CIR CLIPS USED FOR ASSEMBLY IS OF A 16. THE GYM EQUIPMENT SHALL BE FINISHED SMOOTH WITH A PRIMER COATING OF AT LEAST 40 MICRON FOLLOWED BY EPOXY BASED POWDER COATING WITH POLYSTER POWDER COATING OF AT LEAST 60 TO 70 MICRON THICKNESS USING EXONOBEL / BERGER MAKE PAINTS OR ITS EQUIVALENT PAINTS. THE HOLDING DOWN/FIXING OF GYM EQUIPMENTS SHALL BE EMBODED IN CEMENT CONCRETE IN THE RATIO OF 1:2:4 (1 CEMENT : 2 COARSE SAND : 4 STONE AGG. 20MM NOMINAL SIZE)

TAICHI SPINNER ( DIMENSIONS: - 700MM (LENGTH) X 1000MM (WIDTH) X 1280MM (HEIGHT). SAFE AREA:- 1.9MTR X 1.9MTR TAICHI SPINNER EQUIPMENT MADE UP OF “C” CLASS G.I. PIPE OF DIFFERENT NB.NB STANDS FOR NOMINAL BORE SIZES I.E. INTERNAL DIAMETER OF PIPE IN MILLIMETERS. THE CENTER PIPE IS OF 100NB MADE UP OF “C” CLASS G.I. PIPE. THE HANDLE MOVEMENT ROUND FRAME IS MADE UP FROM 25 NB “C” CLASS G.I. PIPE. THE FOUNDATION USED FOR FIXING IS A STRUCTURE AND MADE FROM CENTER PIPE OF G.I. OF 80 NB“C” CLASS WELDED WITH M.S. ROUND PLATE OF DIA 250 MM & 10MM THICK. MAIN PIPE SUPPORTED WITH 25 MM X 25MM M.S. ANGLES OF 3 MM THICKNESS AND 20MM X 40MM CRC SQUARE PIPES OF 3MM THICKNESS. CLOSING CAPS ARE MADE UP OF INJECTION MOULDED PLASTIC LLDPE / HDPE. THE PINS USED ARE MADE UP OF DIA 25 MM OF SAE8620 BRIGHT MATERIAL. THE BEARING USED IS “62012RS1” & “62052RS1” PERMANENT LUBRICATED SEALED BEARING OF REPUTED BRAND. HIGH TENSILE S.S. NUT BOLTS ARE USED FOR ASSEMBLY. FOUNDATION COVER CLOSING CAP IS MADE OF INJECTION MOULDED PLASTIC LLDPE / HDPE. THE CER CLIPS USED FOR ASSEMBLY IS OF A24 AND A11.THE NYLON BUSH IS USED FOR HANDLE KNOB. THE GYM EQUIPMENT SHALL BE FINISHED SMOOTH WITH A PRIMER COATING OF AT LEAST 40 MICRON FOLLOWED BY EPOXY BASED POWDER COATING WITH POLYSTER POWDER COATING OF AT LEAST 60 TO 70 MICRON THICKNESS USING EXONOBEL / BERGER MAKE PAINTS OR ITS EQUIVALENT PAINTS. THE HOLDING DOWN/FIXING OF GYM EQUIPMENTS SHALL BE EMBODED IN CEMENT CONCRETE IN THE RATIO OF 1:2:4 (1CEMENT : 2 COARSE SAND :4 STONE AGG. 20MM NOMINAL SIZE). BOLT M8X16 MM AND NYLOCK NUT OF M8 MADE OF SS 304 USED ON NYLON CAP MOUNTED ON PINS TO PROTECT BEARINGS AND PINS FROM RAIN AND DUST.

ARM AND PADDLE BIKE (DIMENSIONS: - - 1100MM (LENGTH) X 500MM (WIDTH) X 900MM (HEIGHT). SAFE AREA: - 2000MM (LENGTH)X1000MM(WIDTH). ARM AND PADDLE BIKE MADE FROM “C” CLASS GI PIPE. THE CENTER PIPE IS OF 40MM NB MADE FROM “C” CLASS GI PIPE. THE HANDLES IS MADE UP OF CASTED IRON MATERIAL WITH PLASTIC HOLDING GRIPS. FOR FOUNDATION HOLE PASS PROVISION IS PROVIDED. THE FOOTRESTS IS MADE FROM ALUMINUM CASTING MATERIAL, ITS SIZES ARE 130 MM X 300 MM & 3 MM THICKNESS. THE SEATS AND BACK RESTS ARE FITTED ON THE OUTER FRAMES ARE MADE UP OF M.S. SHEET OF SIZE 330 MM X 300 MMX2MM THICKNESS AND DEEP DRAWN AND PRESSED IN TOOLS AND DIES TO HAVE UNIFORM RADIUS OF 20 MM WITH NO SHARP EDGES. THE PINS USED IS MADE UP OF 25 MM DIAMETER HARDEN LOW CARBON STEEL. THE BEARINGS USED IS OF “6205” PERMANENT LUBRICATED SEALED BEARING. THE NUT BOLTS USED FOR ASSEMBLY ARE MADE FROM S.S. MATERIAL. THE GYM EQUIPMENT SHALL BE FINISHED SMOOTH WITH A PRIMER COATING OF AT LEAST 40 MICRON FOLLOWED BY EPOXY BASED POWDER COATING WITH POLYSTER POWDER COATING OF AT LEAST 60 TO 70 MICRON THICKNESS USING EXONOBEL / BERGER MAKE PAINTS OR ITS EQUIVALENT PAINTS. THE HOLDING DOWN/FIXING OF GYM EQUIPMENTS SHALL BE EMBODED IN CEMENT CONCRETE IN THE RATIO OF 1:2:4 (1CEMENT : 2 COARSE SAND :4 STONE AGG. 20MM NOMINAL SIZE).

AIR WALKER PROVIDING AND FIXING AIR WALKER MADE FROM “C” CLASS GI PIPE. THE CENTER PIPE IS OF 80MM NB MADE FROM “C” CLASS MS PIPE, 32MM NB:- AIR WALKER PEDAL FRAME DULY BEND, 25MM NB:- AIR WALKER HANDLE FRAME DULY BEND AND THE BOTTOM SUPPORT OF M.S. ROUND PLATE OF 250 MM DIA& 10MM THICKNESS IS WELDED AT BOTTOM. MS PLATE OF 245 X 113 X 2.8MM :- FOOTREST SUPPORT PLATE. THE LEG MOVEMENT FRAME IS OF 40MM NB MADE FROM “C” CLASS MS PIPE. THE HANDLE FRAME IS OF 25MM NB MADE FROM “C” CLASS GI PIPE. THE FOUNDATION USED FOR FIXING IS CONSISTS OF THREE EQUAL ITEMS I.E. 80MM NB MADE FROM “C” CLASS GI PIPE, M.S. ROUND PLATE OF 250 MM DIA & 10MM THICKNESS & 25 MM X 25MM M.S. ANGLE OF 3 MM THICKNESS. MS PIPE 48 X 48 X 2.8MM:- FOOTREST FRAME SUPPORT. MS ANGLE 23 X 23 X 1.8MM:- FOUNDATION SUPPORT FRAME. MS FLAT 48 X 9MM:- FOUNDATION PLATE SUPPORT. MS BRIGHT MATERIAL:- PINS MADE OF DIA.25MM. MS PLATE OF 8MM:- AIR WALKER PEDAL L-BEND, SUPPORT. 60MM DIA SEAMLESS PIPE:- BUSHES. BEARINGS:- PERMANENT LUBRICATED BEARINGS 6205. CLOSING CAPS MADE FROM TOP QUALITY FRP MATERIAL WITH 2 MM THICKNESS. HDPE / LLDPE PLASTIC :- CLOSING CAP, AIR WALKER FOOTREST. THE PINS USED ARE MADE UP OF 25MM DIAMETER BRIGHT BAR. THE BEARINGS USED BE PERMANENT LUBRICATED SEALED BEARING OF REPUTED MAKE. THE NUT BOLTS USED FOR ASSEMBLY ARE MADE FROM S.S. MATERIAL. THE SER CLIPS USED FOR ASSEMBLY ARE OF 25 MM DIAMETER. THE GYM EQUIPMENT SHALL BE FINISHED SMOOTH WITH A PRIMER COATING OF AT LEAST 40 MICRON FOLLOWED BY EPOXY BASED POWDER COATING WITH POLYSTER POWDER COATING OF AT LEAST 60 TO 70 MICRON THICKNESS USING EXONOBEL / BERGER MAKE PAINTS OR ITS EQUIVALENT PAINTS. THE HOLDING DOWN/FIXING OF GYM EQUIPMENTS SHALL BE EMBEDDED IN CEMENT CONCRETE IN THE RATIO OF 1:2:4 (1CEMENT : 2 COARSE SAND :4 STONE AGG. 20MM NOMINAL SIZE)

PROVIDING AND FIXING SURF BOARD MADE FROM “C” CLASS GI PIPE. THE CENTER PIPE IS OF 100MM NB MADE FROM “C” CLASS GI PIPE, AND THE BOTTOM SUPPORT OF M.S. PLATE OF 250 MM DIA& 10MM THICKNESS IS WELDED AT BOTTOM. THE HANDLE FRAME IS OF 40MM NB & 25MM NB MADE FROM “C” CLASS GI PIPE. THE MOVEMENT FRAME IS MADE UP OF 50MM NB “C” CLASS GI PIPE. THE FOUNDATION USED FOR FIXING CONSISTS OF THREE EQUAL ITEMS I.E. 100MM NB MADE FROM “C” CLASS GI PIPE, M.S. ROUND PLATE OF 250 MM DIAMETER & 10MM THICKNESS, 25MM X 25MM X 3MM M.S. ANGLE. TO JOIN THE CENTRE PIPE & HANDLE FRAME SEAMLESS PIPE OF 130MM DIA& 3MM THICKNESS IS USED. FOR THE MOVEMENT, BUSHES ARE USED & FOR IT 60MM DIA WITH 3MM THICKNESS & 60MM SOLID BAR IS USED. THE FOOTRESTS IS MADE FROM FRP/C.I./ALUMINUM CASTING MATERIAL, ITS SIZES ARE 320 MM X 270 MM & 5 MM THICKNESS. FOR SUPPORT OF FOOTREST IS 200MM X 250MM WITH 5MM THICKNESS M.S. PLATE AND 50MM X 50MM CRC SQUARE PIPE WITH 2MM THICKNESS IS USED. CLOSING CAPS MADE FROM TOP QUALITY FRP MATERIAL WHICH IS OF 2 MM THICKNESS. THE PINS USED ARE MADE UP OF 25 MM DIAMETER HARDEN BRIGHT BAR. THE BEARING USED BE PERMANENT LUBRICATED SEALED BEARING OF REPUTED MAKE. THE HANDLES USED ARE OF RUBBER GRIP. THE NUT BOLTS USED FOR ASSEMBLY IS MADE FROM S.S. MATERIAL. THE BUSHES (STOPPER) USED TO AVOID THE COLLUSION MADE FROM POLY URETHIN PLASTIC MATERIAL OF 50 MM DIA. THE SER CLIPS USED FOR ASSEMBLY IS OF 25 MM DIA. THE GYM EQUIPMENT SHALL BE FINISHED SMOOTH WITH A PRIMER COATING OF AT LEAST 40 MICRON FOLLOWED BY EPOXY BASED POWDER COATING WITH POLYSTER POWDER COATING OF AT LEAST 60 TO 70 MICRON THICKNESS USING EXONOBEL / BERGER MAKE PAINTS OR ITS EQUIVALENT PAINTS. THE HOLDING DOWN/FIXING OF GYM EQUIPMENTS SHALL BE EMBEDDED IN CEMENT CONCRETE IN THE RATIO OF 1:2:4 (1CEMENT : 2 COARSE SAND :4 STONE AGG. 20MM NOMINAL SIZE).

TRIPPLE TWISTER STANDING DIMENSIONS: - 1150MM (LENGTH) X 1150MM (WIDTH) X 1580MM. (HEIGHT). SAFE AREA: - DIA 2.1MTR. TRIPLE TWISTER MADE FROM “C” CLASS GALVANIZED IRON (G.I.) PIPE OF DIFFERENT NB. NB STANDS FOR NOMINAL BORE SIZES I.E. INTERNAL DIAMETER OF PIPE IN MILLIMETERS. THE CENTER PIPE IS OF 100NB MADE FROM OR “C” CLASS G.I. ROUND PIPE. THE BOTTOM SUPPORT WELDED IS OF M.S. ROUND PLATE OF DIA 250 MM & 10MM THICK. THE STANDING FRAME IS OF 32NB MADE FROM “C” CLASS G.I. PIPE. THE HANDLE FRAME OF TRIPLE TWISTER IS OF 25 MM NB MADE FROM OR “C” CLASS G.I. PIPE. THE FOUNDATION USED FOR FIXING IS A STRUCTURE AND MADE FROM CENTER PIPE OF G.I. OF 80MM NB OR “C” CLASS WELDED WITH M.S. ROUND PLATE OF DIA 250 MM & 10MM THICK. MAIN PIPE SUPPORTED WITH 25 MM X 25MM M.S. ANGLE OF 3 MM THICKNESS AND 20MM X 40MM CRC SQUARE PIPE OF 3MM THICKNESS THE STANDING PLATE IS FITTED ON THE FRAME MADE UP OF DIA 80MM SEAMLESS PIPE. M.S. ROUND PLATE OF SIZE DIA 300MM X 10MM THICKNESS. CLOSING CAPS OF TOP QUALITY FIBER REINFORCED PLASTIC MATERIAL WHICH IS OF 2 MM THICK. THE PINS USED ARE MADE UP OF DIA 25 MM SAE8620 BRIGHT MATERIAL. THE BEARINGS USED ARE OF “6205ZZ” PERMANENT LUBRICATED SEALED BEARING OF REPUTED BRAND (FAG/SKF). HIGH TENSILE STEEL WITH GALVANIZED NUTS & BOLTS ARE USED FOR ASSEMBLY. THE GYM EQUIPMENT SHALL BE FINISHED SMOOTH WITH A PRIMER COATING OF AT LEAST 40 MICRON FOLLOWED BY EPOXY BASED POWDER COATING WITH POLYSTER POWDER COATING OF AT LEAST 60 TO 70 MICRON THICKNESS USING EXONOBEL / BERGER MAKE PAINTS OR ITS EQUIVALENT PAINTS. THE HOLDING DOWN/FIXING OF GYM EQUIPMENTS SHALL BE EMBEDDED IN CEMENT CONCRETE IN THE RATIO OF 1:2:4 (1CEMENT : 2 COARSE SAND :4 STONE AGG. 20MM NOMINAL SIZE)

DOUBLE TWISTER (DIMENSIONS: - 1700MM (LENGTH) X 540MM (WIDTH) X 1250MM. (HEIGHT). SAFE AREA: - 3 MTR X 1MTR. DOUBLE TWISTER EQUIPMENT MADE FROM “C” CLASS G.I. PIPE OF DIFFERENT NB. NB STANDS FOR NOMINAL BORE SIZES I.E. INTERNAL DIAMETER OF PIPE IN MILLIMETRES. THE CENTER PIPE IS OF 100MM NB MADE FROM “C” CLASS G.I. ROUND PIPE. THE M.S. ROUND PLATE OF DIA 250 MM & 10MM THICKNESS IS WELDED AT BOTTOM. THE STANDING FRAME OF THE DOUBLE TWISTER IS OF 32 NB MADE FROM “C” CLASS G.I. PIPE. THE HANDLE FRAME OF DOUBLE TWISTER IS 25 NB. THE FOUNDATION USED FOR FIXING IS A STRUCTURE AND MADE FROM CENTER PIPE OF G.I. OF 80 NB “C” CLASS, WELDED WITH M.S. ROUND PLATE OF DIA 250 MM & 10MM THICK. MAIN PIPE SUPPORTED WITH 25 MM X 25MM M.S. ANGLES OF 3 MM THICKNESS AND 20MM X 40MM CRC SQUARE PIPES OF 3MM THICKNESS. THE TWISTER PLATE FITTED ON THE STANDING FRAME IS MADE UP OF M.S. ROUND PLATE OF SIZE 300MM DIAMETER AND 10MM THICKNESS. CLOSING CAPS MADE FROM TOP QUALITY FIBER REINFORCED PLASTIC MATERIAL WHICH IS OF 2 MM THICK. THE PINS USED ARE MADE UP OF DIA 25 MM MS BRIGHT MATERIAL. THE BEARINGS USED ARE OF “6205ZZ” PERMANENT LUBRICATED SEALED BEARING OF REPUTED BRAND. HIGH TENSILE STEEL WITH GALVANIZED NUTS & BOLTS ARE USED FOR ASSEMBLY. THE GYM EQUIPMENT SHALL BE FINISHED SMOOTH WITH A PRIMER COATING OF AT LEAST 40 MICRON FOLLOWED BY EPOXY BASED POWDER COATING WITH POLYSTER POWDER COATING OF AT LEAST 60 TO 70 MICRON THICKNESS USING EXONOBEL / BERGER MAKE PAINTS OR ITS EQUIVALENT PAINTS. THE HOLDING DOWN/FIXING OF GYM EQUIPMENTS SHALL BE EMBEDDED IN CEMENT CONCRETE IN THE RATIO OF 1:2:4 (1CEMENT : 2 COARSE SAND :4 STONE AGG. 20MM NOMINAL SIZE).

SEATED TWISTER THREE IN ONE (DIMENSIONS: - 1150MM (LENGTH) X 1150MM (WIDTH) X 1300MM (HEIGHT). SAFE AREA: - 2MTR X 2MTR. SEATED TWISTER EQUIPMENT MADE FROM “C” CLASS G.I. PIPE OF DIFFERENT NB. NB STANDS FOR NOMINAL BORE SIZES I.E. INTERNAL DIAMETER OF PIPE IN MILLIMETERS THE CENTER PIPE IS OF 80 NB MADE FROM “C” CLASS G.I. PIPE. THE CHAIR PIPE IS OF 50 NB MADE FROM “C” CLASS G.I. PIPE. THE M.S. ROUND PLATE OF DIA 250 MM & 10MM THICKNESS IS WELDED AT BOTTOM. THE SUPPORTING FRAME OF THE SEATED TWISTER IS OF 32 NB MADE FROM “C” CLASS G.I. PIPE. THE HANDLE FRAME OF SEATED TWISTER IS OF 25 MM NB MADE FROM “C” CLASS G.I. PIPE. THE FOUNDATION USED FOR FIXING IS A STRUCTURE AND MADE FROM CENTER PIPE OF G.I. OF 80 NB “C” CLASS, WELDED WITH M.S. ROUND PLATE OF DIA 250 MM & 10MM THICK. MAIN PIPE SUPPORTED WITH 25 MM X 25MM M.S. ANGLES OF 3 MM THICKNESS AND 20MM X 40MM CRC SQUARE PIPES OF 3MM THICKNESS. THE TWISTER PLATE IS FITTED ON THE SUPPORTING FRAME IS MADE UP OF 60NB SEAMLESS PIPE. DIA 300MM X 10MM THICKNESS M.S. ROUND PLATE. CLOSING CAPS MADE FROM TOP QUALITY FIBER REINFORCED PLASTIC MATERIAL WHICH IS OF 2 MM THICKNESS. THE BEARINGS USED BE PERMANENT LUBRICATED SEALED BEARING OF REPUTED BRAND. HIGH TENSILE STEEL WITH GALVANIZED NUTS AND BOLTS ARE USED FOR ASSEMBLY. THE GYM EQUIPMENT SHALL BE FINISHED SMOOTH WITH A PRIMER COATING OF AT LEAST 40 MICRON FOLLOWED BY EPOXY BASED POWDER COATING WITH POLYSTER POWDER COATING OF AT LEAST 60 TO 70 MICRON THICKNESS USING EXONOBEL / BERGER MAKE PAINTS OR ITS EQUIVALENT PAINTS. THE HOLDING DOWN/FIXING OF GYM EQUIPMENTS SHALL BE EMBEDDED IN CEMENT CONCRETE IN THE RATIO OF 1:2:4 (1CEMENT : 2 COARSE SAND :4 STONE AGG. 20MM NOMINAL SIZE)

SHOULDER BUILDER PROVIDING AND FIXING SHOULDER BUILDER MADE FROM C- CLASS GI PIPE. THE CENTER PIPE IS OF 100MM NB MADE FROM “C” CLASS GI PIPE, AND THE BOTTOM SUPPORT OF M.S. ROUND PLATE OF 250 MM DIAMETER & 10MM THICKNESS IS WELDED AT BOTTOM. THE HANDLE MOVEMENT FRAME IS OF 25 NB & 20 NB MADE FROM “C” CLASS GI PIPE. TO JOIN THE CENTRE PIPE & HANDLE MOVEMENT FRAME SEAMLESS PIPE OF 130MM DIA& 3MM THICKNESS IS USED. THE FOUNDATION USED FOR FIXING CONSISTS OF THREE EQUAL ITEMS I.E. 100MM NB MADE FROM “C” CLASS GI PIPE, M.S. ROUND PLATE OF 250 MM DIA& 10MM THICKNESS & 25 MM X 25MM X 3MM M.S. ANGLE. CLOSING CAPS MADE FROM TOP QUALITY FRP MATERIAL WHICH IS OF 2 MM THICKNESS. THE PINS USED ARE MADE UP OF 25 MM DIA BRIGHT BAR. THE BEARING USED BE PERMANENT LUBRICATED SEALED BEARING OF REPUTED MAKE. THE NUT BOLTS USED FOR ASSEMBLY ARE MADE FROM S.S. MATERIAL. THE SERCLIPS USED FOR ASSEMBLY IS OF 25 MM DIAMETER. THE POLY URETHIN PLASTIC BUSH IS USED FOR HANDLING. THE GYM EQUIPMENT SHALL BE FINISHED SMOOTH WITH A PRIMER COATING OF AT LEAST 40 MICRON FOLLOWED BY EPOXY BASED POWDER COATING WITH POLYSTER POWDER COATING OF AT LEAST 60 TO 70 MICRON THICKNESS USING EXONOBEL / BERGER MAKE PAINTS OR ITS EQUIVALENT PAINTS. THE HOLDING DOWN/FIXING OF GYM EQUIPMENTS SHALL BE EMBEDDED IN CEMENT CONCRETE IN THE RATIO OF 1:2:4 (1CEMENT : 2 COARSE SAND :4 STONE AGG. 20MM NOMINAL SIZE)

COMBINATION SET (3 IN ONE) OF AIR WALKER + LEG PRESS + SHOULDER BUILDER (DIMENSIONS: - 2150MM (LENGTH) X 950MM (WIDTH) X 1600MM.(HEIGHT). SAFE AREA:- 3.0 MTR X2.0MTR. AIR WALKER CUM LEG PRESS CUM SHOULDER BUILDER EQUIPMENT MADE FROM “C” CLASS G.I. PIPE OF DIFFERENT NB. NB STANDS FOR NOMINAL BORE SIZES I.E. INTERNAL DIAMETER OF PIPE IN MILLIMETERS. THE MAIN FRAME IS OF 100 NB MADE FROM “C” CLASS GI PIPE. THE BOTTOM SUPPORT FRAME OF M.S. 40MM X 75MM X 3MM THICK C CHANNEL. SEAT FITTED ON THE OUTER FRAMES ARE MADE UP OF M.S. SHEET OF SIZE 330 MM X 300MMX2MM THICKNESS AND DEEP DRAWN AND PRESSED TOOLS AND DIES TO HAVE UNIFORM RADIUS OF 20 MM WITH NO SHARP EDGES. THE BOTTOM SUPPORT FRAME OF M.S. 40MM X80MMX3MM THICK RECTANGULAR PIPE. THE LEG MOVEMENT FRAME IS OF 32NB MADE FROM “C” CLASS G.I. PIPE. THE HANDLE FRAME IS OF 25NB MADE FROM “C” CLASS G.I. PIPE. CLOSING CAPS ARE MADE UP OF INJECTION MOULDED PLASTIC LLDPE / HDPE. PINS USED OF DIAMETER 25MM ARE MADE UP FROM SAE 8620 BRIGHT MATERIAL. BOLT M8X16 MM AND NYLOCK NUT OF M8 MADE OF SS 304 USED ON NYLON CAP MOUNTED ON PINS TO PROTECT BEARINGS AND PINS FROM RAIN AND DUST. THE BEARINGS BE USED PERMANENT LUBRICATED SEALED BEARING OF REPUTED MAKE BRAND. HIGH TENSILE STEEL GALVANIZED NUTS & BOLTS ARE USED FOR ASSEMBLY.A24 MM CIRCLIPS ARE USED FOR ASSEMBLY.25 NB G.I. PIPE IS USED FOR ROTARY RING OF SHOULDER BUILDER. THE FOOTRESTS ARE MADE FROM INJECTION MOULDED PLASTIC LLDPE / HDPE, WITH THE SUPPORT OF 310MM X 130MM X 3MM THICK MS PLATE. EQUIPMENT HAS BOLTING PROVISION FOR MOUNTING ON CONCRETE SLAB. THE GYM EQUIPMENT SHALL BE FINISHED SMOOTH WITH A PRIMER COATING OF ATLEAST 40 MICRON FOLLOWED BY EPOXY BASED POWDER COATING WITH POLYSTER POWDER COATING OF AT LEAST 60 TO 70 MICRON THICKNESS USING EXONOBEL / BERGER MAKE PAINTS OR ITS EQUIVALENT PAINTS. THE HOLDING DOWN/FIXING OF GYM EQUIPMENTS SHALL BE EMBEDDED IN CEMENT CONCRETE IN THE RATIO OF 1:2:4 (1CEMENT : 2 COARSE SAND :4 STONE AGG. 20MM NOMINAL SIZE).

COMBINATION AIR WALKER + LEG PRESS + SEATING TWISTER (DIMENSIONS: - 2300MM (LENGTH) X 860MM (WIDTH) X 1600MM.(HEIGHT). SAFE AREA:- 1.39 X 1.27MTR. AIR WALKER CUM LEG PRESS CUM SEATING TWISTER EQUIPMENT MADE FROM “C” CLASS G.I. PIPE OF DIFFERENT NB. NB STANDS FOR NOMINAL BORE SIZES I.E. INTERNAL DIAMETER OF PIPE IN MILLIMETERS. THE MAIN FRAME OF 100NB MADE FROM “C” CLASS G.I. PIPE. THE BOTTOM SUPPORT FRAME OF GI 40MM X80MMX3MM THICK RECTANGULAR PIPE. THE LEG MOVEMENT FRAME IS OF 32NB MADE FROM “B” OR “C” CLASS G.I. PIPE. THE HANDLE FRAME IS OF 25NB MADE FROM “C” CLASS G.I. PIPE. CLOSING CAPS MADE FROM TOP QUALITY FIBER REINFORCED PLASTIC MATERIAL WITH 2 MM THICKNESS. PINS USED OF DIAMETER 25MM ARE MADE UP FROM SAE 8620 BRIGHT MATERIAL. THE BEARINGS BE USED PERMANENT LUBRICATED SEALED BEARING OF REPUTED MAKE BRAND. HIGH TENSILE STEEL GALVANIZED NUTS & BOLTS ARE USED FOR ASSEMBLY.DIA 25 MM CERCLIPS ARE USED FOR ASSEMBLY. 300MM DIAMETER X 10MM THICK PLATE CAN BE USED FOR ROTATING SEAT OF SEATING TWISTER WITH 50NB VERTICAL G.I. PIPE. THE FOOTRESTS ARE MADE FROM CASTED ALUMINUM MATERIAL, HAVING SIZES 130MM X 310MM X 5MM THICK. WITH THE SUPPORT OF 310MM X 130MM X 3MM THICK MS PLATE. IT HAS BOLTING PROVISION FOR MOUNTING ON CONCRETE SLAB. TO BUILD STRUCTURE BUSHES ARE USED WHICH ARE MADE FROM SEAMLESS PIPE OF 50MM O.D. AND 6MM THICKNESS AS WELL AS 50MM DIAMETER SOLID BAR IS USED. THE GYM EQUIPMENT SHALL BE FINISHED SMOOTH WITH A PRIMER COATING OF AT LEAST 40 MICRON FOLLOWED BY EPOXY BASED POWDER COATING WITH POLYSTER POWDER COATING OF AT LEAST 60 TO 70 MICRON THICKNESS USING EXONOBEL / BERGER MAKE PAINTS OR ITS EQUIVALENT PAINTS. THE HOLDING DOWN/FIXING OF GYM EQUIPMENTS SHALL BE EMBEDDED IN CEMENT CONCRETE IN THE RATIO OF 1:2:4 (1CEMENT : 2 COARSE SAND :4 STONE AGG. 20MM NOMINAL SIZE)

COMBINATION AIR WALKER + LEG PRESS + STANDING TWISTER (DIMENSIONS:- 2250MM (LENGTH)X 860MM (WIDTH) X 1600MM.(HEIGHT). SAFE AREA:-3.0MTRX1.8MTR. AIR WALKER CUM LEG PRESS CUM STANDING TWISTER EQUIPMENT MADE FROM “C”CLASS G.I.PIPE OF DIFFERENT NB. NB STANDS FOR NOMINAL BORE SIZES I.E. INTERNAL DIAMETER OF PIPE IN MILLIMETERS. THEMAINFRAMEOF100NB MADE FROM “C” CLASS G.I. PIPE. THE BOTTOM SUPPORT FRAME OF THICK RECTANGULAR PIPE. THE LEG MOVEMENT FRAMEIS OF32NB MADE FROM “C”CLASS G.I. PIPE. THE HANDLE FRAME IS OF25NB MADE FROM “C” CLASS G.I. PIPE. CLOSING CAPS MADE FROM TOP QUALITY FIBER REINFORCED PLASTIC MATERIAL WITH 2 MM THICKNESS. PINSUSED OF DIAMETER 25MMAREMADEUPFROM BRIGHT MATERIAL. THE BEARINGS USED BE PERMANENT LUBRICATED SEALED BEARING OF REPUTED BRAND (SKF/FAG). HIGH TENSILE STEEL GALVANIZED NUTS & BOLTS ARE USED FOR ASSEMBLY. DIA 25MMCERCLIPS ARE USED FOR ASSEMBLY. 300MM DIAMETER X 10MM THICK PLATE CAN BE USED FOR ROTATING SEAT OF STANDING TWISTER WITH 50NB VERTICAL G.I. PIPE. THE FOOTRESTS ARE MADE FROM CASTED ALUMINUM MATERIAL, HAVING SIZES 130MM X 310MM X 5MM THICK. WITH THE SUPPORT OF 310MM X 130MM X 3MM THICK MS PLATE. IT HAS BOLTING PROVISION FOR MOUNTING ON CONCRETE SLAB. TO BUILD STRUCTURE BUSHES AREUSEDWHICHAREMADE FROM SEAMLESS PIPE OF 50MM O.D. AND 6MMTHICKNESS AS WELL AS 50MM DIAMETER SOLID BAR IS USED. THE GYM EQUIPMENT SHALL BE FINISHED SMOOTH WITH A PRIMER COATING OF AT LEAST 40 MICRON FOLLOWED BY EPOXY BASED POWDER COATING WITH POLYSTER POWDER COATING OF AT LEAST 60 TO 70 MICRON THICKNESS USING EXONOBEL / BERGER MAKE PAINTS OR ITS EQUIVALENT PAINTS. THE HOLDING DOWN/FIXING OF GYM EQUIPMENTS SHALL BE EMBEDDED IN CEMENT CONCRETE IN THE RATIO OF 1:2:4 (1CEMENT : 2 COARSE SAND :4 STONE AGG. 20MM NOMINAL SIZE)

DOUBLE PULL DOWN (DIMENSIONS: - 1200 MM (LENGTH) X 750 MM (WIDTH) X 2000 MM (HEIGHT). DOUBLE PULL DOWN IS MADE FROM “C” CLASS GI-PIPE. THE CENTER PIPE IS OF 100MM NB MADE FROM “C” CLASS GI-PIPE, AND THE BOTTOM SUPPORT IS OF MS ROUND PLATE OF 250MM DIA& 10MM THICK IS WELDED AT THE BOTTOM OF THE PIPE. THE REMAINING FRAME IS MADE OF 32MM NB & 50MM NB “C” CLASS GI-PIPE. THE HANDLE FRAME IS MADE OF 32MM NB & 25MM NB “C” CLASS GI-PIPE. MIDDLE SUPPORT IS OF 25MM NB “C” CLASS GI-PIPE. LOWER FRAME IS MADE OF 32MM NB & 25MM NB “C” CLASS GI-PIPE. FOR THE ASSEMBLY DIFFERENT BUSHES ARE USED WHICH IS MADE FROM 60MM WITH 3MM THICK SEAMLESS PIPE IS USED. THE FOUNDATION USED FOR FIXING IT CONSIST OF THREE EQUAL ITEMS I.E 80MM NB MADE FROM “C” CLASS GI-PIPE, MS ROUND PLATE OF 250MM DIA&10MM THICK, 25MMX25MMX3MM MS ANGLE. CLOSING CAPS ARE MADE FROM TOP QUALITY LLDPE MATERIAL WHICH IS OF 2MM THICK. THE PINS USED ARE MADE UP OF 25MM & 17MM DIA SOLID BAR. THE BEARINGS USED ARE OF “6205 & 6203” PERMANENT LUBRICATED SEALED BEARING OF REPUTED MAKE. THE NUT BOLTS USED FOR ASSEMBLY ARE MADE FROM SS MATERIAL.HIGH TENSILE STEEL WITH GALVANIZED NUTS & BOLTS ARE USED FOR ASSEMBLY. THE CIRCLIPS USED FOR ASSEMBLY IS MADE UP OF 25MM & 17MM DIA. THE FOUNDATION PIPES ARE EMBEDDED IN CC STOCK AND PAINTING IS DONE BY ATTRACTIVE COLOR SPRAYING AFTER PROPER SURFACE TREATMENT, THE INITIAL COAT OF PRIMER SURFACE IS APPLIED BEFORE TOP COAT. THE POWDER COATING IS DONE FROM POLY RETHANE& EPOXY POWDER WITH 60 TO 70 MICRON THICKNESS.THE HOLDING DOWN/FIXING OF GYM EQUIPMENTS SHALL BE EMBODED IN CEMENT CONCRETE IN THE RATIO OF 1:2:4 (1CEMENT : 2 COARSE SAND :4 STONE AGG. 20MM NOMINAL SIZE)

TRICEPS PULLER (DIMEMSIONS:- 2110MM (LENGTH) X 600MM (WIDTH) X 1600MM (HEIGHT) TRICEPS PULLER IS MADE FROM “C” CLASS GI-PIPE. THE CENTER PIPE IS OF 100MM NB MADE FROM “C” CLASS GI-PIPE, AND THE BOTTOM SUPPORT IS OF MS ROUND PLATE OF 250MM DIA& 10MM THICK IS WELDED AT THE BOTTOM OF THE PIPE. THE REMAINING FRAME IS MADE OF 32MM NB “C” CLASS GI-PIPE. THE HANDLE FRAME IS MADE OF 32MM NB & 25MM NB “C” CLASS GI-PIPE. THE SEAT FRAME IS OF 32MM NB “C” CLASS GI-PIPE. FOR THE ASSEMBLY DIFFERENT BUSHES ARE USED WHICH IS MADE FROM 60MM WITH 3MM THICK SEAMLESS PIPE IS USED. THE FOUNDATION USED FOR FIXING IT CONSIST OF THREE EQUAL ITEMS I.E 80MM NB MADE FROM “C” CLASS GI-PIPE, MS ROUND PLATE OF 250MM DIA& 10MM THICK, 25MMX25MMX3MM MS ANGLE. CLOSING CAPS ARE MADE FROM TOP QUALITY LLDPE MATERIAL WHICH IS OF 2MM THICK. THE PINS USED ARE MADE UP OF 25MM & 17MM DIA SOLID BAR. THE BEARINGS USED ARE OF “6205 & 6203” PERMANENT LUBRICATED SEALED BEARING OF REPUTED MAKE. THE NUT BOLTS USED FOR ASSEMBLY ARE MADE FROM SS MATERIAL. THE CIRCLIP USED FOR ASSEMBLY IS MADE UP OF 25MM & 17MM DIA.HIGH TENSILE STEEL WITH GALVANIZED NUTS & BOLTS ARE USED FOR ASSEMBLY. THE FOUNDATION PIPES ARE EMBEDDED IN CC STOCK AND PAINTING IS DONE BY ATTRACTIVE COLOR SPRAYING AFTER PROPER SURFACE TREATMENT, THE INITIAL COAT OF PRIMER SURFACE IS APPLIED BEFORE TOP COAT. THE POWDER COATING IS DONE FROM POLY RETHANE& EPOXY POWDER WITH 60 TO 70 MICRON THICKNESS.THE HOLDING DOWN/FIXING OF GYM EQUIPMENTS SHALL BE EMBODED IN CEMENT CONCRETE IN THE RATIO OF 1:2:4 (1CEMENT : 2 COARSE SAND :4 STONE AGG. 20MM NOMINAL SIZE)

SINGLE SKYWALKER (DIMEMSIONS:- 1850MM (LENGTH) X 520MM (WIDTH) X 1780MM (HEIGHT). SINGLE SKYWALKER IS MADE FROM “C” CLASS GI-PIPE. THE CENTER PIPE IS OF 50MM NB MADE FROM “C” CLASS GI-PIPE, AND THE BOTTOM SUPPORT IS OF MS ROUND PLATE OF 250MM DIA& 10MM THICK IS WELDED AT THE BOTTOM OF THE PIPE. THE REMAINING FRAME IS MADE OF 50MM NB “C” CLASS GI-PIPE. THE HANDLE FRAME IS MADE OF 25MM NB& 32MM NB “C” CLASS GI-PIPE. MIDDLE SUPPORT IS OF 40MM NB “C” CLASS GI-PIPE. LOWER FRAME IS MADE OF 32MM NB “C” CLASS GI-PIPE. FOR THE ASSEMBLY DIFFERENT BUSHES ARE USED WHICH IS MADE FROM 60MM WITH 3MM THICK SEAMLESS PIPE IS USED. THE FOUNDATION USED FOR FIXING IT CONSIST OF THREE EQUAL ITEMS I.E 80MM NB MADE FROM “C” CLASS GI-PIPE, MS ROUND PLATE OF 250MM DIA& 10MM THICK, 25MMX25MMX3MM MS ANGLE. CLOSING CAPS ARE MADE FROM TOP QUALITY LLDPE MATERIAL WHICH IS OF 2MM THICK. THE CIRCLIPS USED FOR ASSEMBLY ARE MADE UP OF 25MM DIA. THE PINS USED ARE MADE UP OF 25MM DIA SOLID BAR. THE BEARINGS USED ARE OF “6205& 6203 PERMANENT LUBRICATED SEALED BEARING OF REPUTED MAKE. THE NUT BOLTS USED FOR ASSEMBLY ARE MADE FROM SS MATERIAL.HIGH TENSILE STEEL WITH GALVANIZED NUTS & BOLTS ARE USED FOR ASSEMBLY THE FOUNDATION PIPES ARE EMBEDDED IN CC STOCK AND PAINTING IS DONE BY ATTRACTIVE COLOR SPRAYING AFTER PROPER SURFACE TREATMENT, THE INITIAL COAT OF PRIMER SURFACE IS APPLIED BEFORE TOP COAT. THE POWDER COATING IS DONE FROM POLY RETHANE& EPOXY POWDER WITH 60 TO 70 MICRON THICKNESS.THE HOLDING DOWN/FIXING OF GYM EQUIPMENTS SHALL BE EMBODED IN CEMENT CONCRETE IN THE RATIO OF 1:2:4 (1CEMENT : 2 COARSE SAND :4 STONE AGG. 20MM NOMINAL SIZE)

LEG PRESS LEG PRESS IS MADE FROM “C” CLASS GI-PIPE. THE CENTER PIPE IS OF 100MM NB MADE FROM “C” CLASS GI-PIPE, AND THE BOTTOM SUPPORT IS OF MS ROUND PLATE OF 250MM DIA& 10MM THICK IS WELDED AT THE BOTTOM OF THE PIPE. THE REMAINING FRAME IS MADE OF 32MM NB “C” CLASS GI-PIPE. THE HANDLE FRAME IS MADE OF 25MM NB “C” CLASS GI-PIPE. MIDDLE SUPPORT IS OF 25MM NB “C” CLASS GI-PIPE. LOWER FRAME IS MADE OF 32MM NB “C” CLASS GI-PIPE. FOR THE ASSEMBLY DIFFERENT BUSHES ARE USED WHICH IS MADE FROM 60MM WITH 3MM THICK SEAMLESS PIPE IS USED. THE FOUNDATION USED FOR FIXING IT CONSIST OF THREE EQUAL ITEMS I.E 80MM NB MADE FROM “C” CLASS GI-PIPE, MS ROUND PLATE OF 250MM DIA& 10MM THICK, 25MMX25MMX3MM MS ANGLE. CLOSING CAPS ARE MADE FROM TOP QUALITY LLDPE MATERIAL WHICH IS OF 2MM THICK. THE PINS USED ARE MADE UP OF 25MM DIA SOLID BAR. THE BEARINGS USED ARE OF “6205 PERMANENT LUBRICATED SEALED BEARING OF REPUTED MAKE. THE NUT BOLTS USED FOR ASSEMBLY ARE MADE FROM SS MATERIAL.HIGH TENSILE STEEL WITH GALVANIZED NUTS & BOLTS ARE USED FOR ASSEMBLY. THE CIRCLIPS USED FOR ASSEMBLY ARE MADE UP OF 25MM DIA. THE FOUNDATION PIPES ARE EMBEDDED IN CC STOCK AND PAINTING IS DONE BY ATTRACTIVE COLOR SPRAYING AFTER PROPER SURFACE TREATMENT, THE INITIAL COAT OF PRIMER SURFACE IS APPLIED BEFORE TOP COAT. THE POWDER COATING IS DONE FROM POLY RETHANE& EPOXY POWDER WITH 60 TO 70 MICRON THICKNESS.THE HOLDING DOWN/FIXING OF GYM EQUIPMENTS SHALL BE EMBODED IN CEMENT CONCRETE IN THE RATIO OF 1:2:4 (1CEMENT : 2 COARSE SAND :4 STONE AGG. 20MM NOMINAL SIZE)

PROVIDING AND FIXING TEST RIG MANUFACTURED BY COMBINATION OF ANTI-CORROSIVE TREATED. MILD STEEL AND ALL-SEASON ARTIFICIAL WOOD TO SEEK ECO-FRIENDLY GREENERY EFFECT. DIMENSIONS: (L X W X H) = 3650X2300X2220 MM. MAIN FRAME COVER - COMPLETELY COVERED TOP TO BOTTOM WITH ALL-SEASON ARTIFICIAL WOOD, OUTER SIZE 120X120MM, 93X93MM INNER AREA TO ACCOMMODATE SQUARE TUBE SHAPE WHICH IS COMPLETELY MOLDED IN ONE SINGLE PIECE. ARTIFICIAL WOOD 100% WATER RESISTANCE AND DULY CERTIFIED BY CII FOR GREEN PRODUCTS. ARTIFICIAL WOOD SHOULD CONSIST WOOD POWDER MORE THAN 50%. U.V. RESISTANCE AS PER IS 14887 – 2000. ALL ROUND PIPES SHOULD BE OF “HEAVY GRADE" AS PER IS 1239 (HIGHEST THICKNESS AS PER IS 1239). MAIN FRAME - CONSIST –. 90X90X3MM THICKNESS SQUARE TUBE GET MAXIMUM INTERNAL STRENGTH TO STRUCTURE. ALL PROFILES USED ARE OF MS SHEET OF 8MM THICK AND DULY CUT ON LASER CUTTING MACHINE WITH NO SHARP EDGE AND SHARP BEND. ALL ACCESSORIES SHOULD BE DEMOUNTABLE TYPE. ALL HANDLE DEMOUNTABLE TYPE – 32 NB HEAVY GRADE GI PIPE ATTACHED 5 MM THICK MS PLATE FOR DEMOUNTABLE SYSTEM NUT & BOLTS - ALL NUT & BOLT MADE FROM STAINLESS STEEL. FOUNDATION STOOL: MADE FROM MAIN PIPE 90X90X3MM PIPE AND TOP SUPPORT OF M.S. PLATE OF 250X250MM SQUARE 10MM THICKNESS IS WELDED TOP. 40X8MM MS FLAT WITH 20X40MM M.S. PIPE. HEIGHT OF STOOL IS 500MM. ALL PILLARS SHOULD HAVE PROVISION OF SQUARE PLATE 250X250X10 MM FOR MOUNTING ON FOUNDATION STOOL. RIG CONSIST OF 1 HORIZONTAL BAR , 2 DOUBLE BAR , PUSH UP HANDLES, 1 LEG RAISE , 1 MONKEY BAR AND 2 CHIN UP HANDLES. CHIN UP SHOULD HAVE LEG RESTING SUPPORT TO BE MADE OF 40X40 MS PIPE AND COVERED WITH 1.5MM THICK SS304 CHECKER PLATE TO AVOID PAINT DAMAGES. LEG RAISE HANDLE SHOULD HAVE HAND GRIP MADE UP OF SS304 MATERIAL. FOUNDATION STOOL DESIGN SUITABLE TO APPLICATION AND IS EMBEDDED IN C.C. 3:2:1 STOCK BELOW GROUND LEVEL. POWDER COATING: - THE POWDERS TO BE USED OF PURE POLYESTER MATERIAL OF AKZONOBEL MAKE WITH 70 TO 90 MICRON THICKNESS. PRE-TREATED WITH PRIMARY COAT OF 40 MICRONS OF ETCH PRIMER WHICH IS SPECIALLY DEVELOPED FOR GI MATERIAL. INSTRUCTION STICKER FOR ALL USES OF SIZE 90MM X 160MM OF SS 304 RUSTPROOF GRADE PLATE WITH 0.8MM THICKNESS DULY LASER MARKED PRINTING & RIVETED ON 5MM THICK MS PLATE. AVOIDED PLASTIC AND PRINTED STICKERS TO HAVE LIFELONG DURABILITY. SAFETY & MAINTENANCE:-ALL EQUIPMENT SHOULD BE TESTED AS PER EN16630 SAFETY NORMS AND CARRIES CE MARK. MAINTENANCE SHOULD BE FOLLOWED AS PER EN 16630 GUIDELINES. THE EQUIPMENT SHOULD BE WITHSTAND FOR THE WEIGHT OF USER UP TO 150KG. USER MANUAL WITH TROUBLE SHOOTING GUIDE SHOULD BE AVAILABLE AND SUPPLY WITH THE EQUIPMENT. DISPLAY FOR HOW TO USE, DO AND DON’TS AND CONTACT DETAILS FOR MAINTENANCE AND GRIEVANCE REDRESSAL SHOULD BE AVAILABLE ON SITE.

DIMENSIONS: - 1450mm (Length) x 450mm (Width) x 1170mm. (Height). • SAFE AREA: - Ø1.5 Mtr. • Double standing Twister made from “B” Class Galvanized Iron (G.I.) Pipe of different NB NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters. • The Center Pipe is of 80NB made from “B” Class G.I. Round Pipe. • The bottom support w e l d e d i s of M.S. round plate of Ø250 mm & 10mm thick. • The handle Sleeve made up of Ø90NB G.I. Pipe and can be disassembled. • The standing frame is of Ø 32NB made from “B” class G.I. pipe. Also Standing frame sleeve is made up of Ø90NB “B” or G.I. pipe and can be disassembled. • The handle frame of double twister is of Ø 25 mm NB made from “B” class G.I. pipe. Also handle frame sleeve is made up of Ø90NB “B” G.I. pipe and can be disassembled. • The foundation used for fixing is a structure and made from center pipe of G.I. of 80mm NB “B” class welded with M.S. round plate of Ø250mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angle of 3 mm thickness and 20mm x 40mm CRC square pipe of 3mm thickness • The standing plate of size Ø250mm x 10mm thickness is welded to bu s h of Ø 70X75 mm M.S. • Button caps of top quality Fiber reinforced Plastic material which is of 2 mm and thickness 3mm. • The Pins used are made up of Ø 35 mm SAE8620 bright material. • To build bush seamless pipe of Ø75mm OD and thickness of 8.5 mm is used. • The bearings used are of “6207zz” permanent lubricated sealed bearing of reputed brand. • High tensile steel with galvanized nuts & bolts are used for assembly. • The powder coating is done w i t h Pure Polyester powder with 60 to 70 micron thickness.

DIMENSIONS: - 1605mm (Length) x 640mm (Width) x 1854mm. (Height). • SAFE AREA:- 1Mtr x 2.5Mtr • Seated puller equipment made up of “B” Class G.I. pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters • The center pipe is of 80NB made from “B” Class G.I. pipe.  Bottom support i s of M.S. round plate of Ø250 mm & 10mm thickness is welded. • Connecting linkage made up of 25NB “B” class G.I. pipe. • The removable sleeve assembly is made up of 90NB “B” class M.S. Pipe. • The handle frame is of 32NB “B” class G.I. pipe. • The seat frame is of 32NB “B” class G.I. pipe, • To build structure bushes are used which are made from seamless pipe of 60mm O.D. and 6mm thickness as well as 50mm diameter solid bar is used. • The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “B” class. Welded with M.S. round plate of Ø250mm& 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. • The seats a r e fitted on the outer frames a r e made up of high quality Fiber reinforce Plastic material of size 250 mm X 220 mm X 10 mm of thickness 4 mm mounted on two M.S. Plate of Size 150mmx150mmx3mm. • Closing caps made from high quality Fiber reinforced Plastic material which is of 2 mm . thickness. • Pins used of Diameter 25mm and 17mm are made up from SAE 8620 bright material. • The bearings used are of “6203zz” permanent lubricated sealed bearing of reputed brand. • Button Caps are made from top quality PolyPropylene Plastic material 2mm and 3mm thickness. • High tensile steel with galvanized nuts & bolts are used for assembly. • A25 and A16 circlips are used for Pin Locking Assembly. • The powder coating is done by Pure Polyester powder with 60 to 70 micron thickness.

• DIMENSIONS: - 1220mm (Length) x 1100mm (Width) x 1150mm. (Height). • SAFE AREA: - Ø1.6 Mtr. • Triple Twister made from “B” Class GalvanizedIron (G.I.) Pipe of different NB NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters. • The Center Pipe is of 80NB made from “B” Class G.I. Round Pipe. • The bottom support w e l d e d i s of M.S. round plate of Ø250 mm & 10mm thick. • The handle Sleeve made up of Ø90NB G.I. Pipe and can be disassembled. • The standing frame is of Ø 32NB made from “B” class G.I. pipe. Also Standing frame sleeve is made up of Ø90NB “B” or G.I. pipe and can be disassembled. • The handle frame of triple twister is of Ø 25 mm NB made from “B” class G.I. pipe. Also handle frame sleeve is made up of Ø90NB “B” G.I. pipe and can be disassembled. • The foundation used for fixing is a structure and made from center pipe of G.I. of 80mm NB “B” class welded with M.S. round plate of Ø250mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angle of 3 mm thickness and 20mm x 40mm CRC square pipe of 3mm thickness • The standing plate is fitted on the frame made up of Ø80mm seamless pipe. M.S. Round Plate of size Ø300mm x 10mm thickness. • Closing caps of top quality Fiber reinforced Plastic material which is of 2 mm thick. • Closing Bolts Caps are made from top quality Fiber Reinforce Plastic material 2mm and 3mm thickness. • The Pins used are made up of Ø 35 mm SAE8620 bright material. • To build bush seamless pipe of Ø75mm OD and thickness of 8.5 mm is used. • The bearings used are of “6207zz” permanent lubricated sealed bearing of reputed brand (FAG/SKF). • High tensile steel with galvanized nuts & bolts are used for assembly. • The powder coating is done w i t h Pure Polyester powder with 60 to 70 micron thickness.

DIMENSIONS: - 910mm (Length) x 400mm (Width) x 1350mm. (Height). • SAFE AREA: - 1.2 Meter x 1.0 Meter • AirWalker Equipment made from “B” Class G.I. Pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters • The main frame of 80NB made from “B” Class G.I. pipe. • The bottom support of M.S. round plate of Ø250mm & 10mm thick. • The leg movement frame is of 32NB made from “B” Class G.I. pipe. • The handle frame is of 25NB made from “B” Class G.I. pipe. • The Sleeve frame is of 90NB made from “B” Class S e a m l e s s M.S. pipe and can be disassembled. This sleeve fitted with SS Bolt M8X16 mm with SS M8 Nylock Nut and protected with Plastic Button caps. • The removable stopper sleeve assembly is made up of 10 mm M.S. flat for safety purpose. • The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “B” class welded with G.I. round plate of Ø250mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. • Foundation Protected with Fiber Reinforced Plastic Base Cover on main pipe and of Outer Diameter 300mm and thickness of 2.00mm. • End Closing Caps made from top quality Fiber reinforced Plastic material with 2 mm thickness. • Pins used of Diameter 25mm are made up from SAE 8620 bright material and protected with nylon caps. • The bearings used are “6205zz” permanent lubricated sealed bearing of reputed brand. • High tensile steel galvanized nuts & bolts are used for assembly. • A24 cerclips are used for pin locking assembly. • The powder coating is done by Pure Polyester powder w i t h 60 to 70 micron thickness. • The footrests are made from casted FRP material, having size 130mm X 310mm X 5mm thick and bolted with the support of 250mm X 115mm X 3mm thick MS plate. • To build structure bushes are used which are made from seamless pipe of 60mm O.D. And 6mm thickness as well as 60mm diameter solid bar is used. • The equipment comes with assembly guide cum instruction cum warranty manual

DIMENSIONS: - 1650mm (Length) x 580mm (Width) x 1670mm. (Height). • SAFE AREA: - 2.0Mtr x 1.2Mtr. • Chest press equipment made up of “B” Class G.I. pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters • The center pipe is of 80NB made up of “B” Class G.I. pipe. • The bottom welded with support of M.S. round plate of Ø250 mm &10mm thickness. • The connecting pipes are made up from 25NB “B” class G.I. pipe. • The handle frame is made up from 32NB “B” class G.I. pipe. • The seat frame is made up from 32NB “B” class G.I. pipe. • The removable sleeve assembly is made up of 90NB “B” class M.S. Pipe. • To build structure bushes are used which are made from seamless pipe of 60mm O.D. and 6mm thickness as well as 50mm O.D. and thickness of 6mm. • The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “B” class Welded with M.S. round plate of Ø250mm& 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. • The seats a r e fitted on the outer frames a r e made up of high quality Fiber reinforce Plastic material of size 250 mm X 220 mm X 10 mm of thickness 4 mm mounted on two M.S. Plate of Size 150mmx150mmx3mm. • Closing Caps are made from top quality Fiber Reinforce Plastic material which is of 2 mm thickness. • Closing Bolts Caps are made from top quality Fiber Reinforce Plastic material 2mm and 3mm thickness. • Pins used of Diameter 25mm and 17mm are made up from SAE 8620 bright material. • The bearings used are of “6205zz” &“6203zz” permanent lubricated sealed bearing of reputed brand. • High tensile steel with galvanized nuts & bolts are used for assembly. • A25 and A16 circlips are used for Pin Locking Assembly. • The powder coating is done by Pure Polyester powder with 60 to 70 micron thickness.

AREA: -1.8Mtr x 0.63Mtr. • HEIGHT: - 1.5 Mtr. • SAFE AREA: - 3.8Mtr x 2.63Mtr. • SkyWalker Equipment made from “B” class G.I. Pipe. • The main frame is of pipe is 100mm NB made from “B” Class G.I. pipe. • For connecting the handle frame to main pipe 50mm NB “B” Class G.I. pipe is used. • The leg movement frame is of 50mmX50mm Square pipe with thickness 2mm is used. • The upper sleeve is made of 115NB and can be dismantled from the main assembly and easily replacable with other one. • The handle pipe is of 25mm NB made from “B” Class G.I. pipe. • The footrests is made from Fiber Reinforced Plastic material, its sizes are 255 X 120 X 3mm. • Closing Caps made from top quality nylon material with 2 mm thickness. • Pins used of Diameter 25mm are made up from SAE 8620 bright material and protected with nylon caps. • The bearings used are “6205zz” are permanent lubricated sealed bearing of reputed brand. • High tensile steel with galvanized nuts & bolts are used for assembly. • The cerclips A24 used for assembly are of Ø25mm. • The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “B” class welded with G.I. round plate of Ø250mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. • To build structure bushes are used which are made from seamless pipe of 60mm O.D. And 6mm thickness as well as 60mm diameter solid bar is used. • M10 SS allen bolt are covered with PP Button caps. • The equipment comes with assembly guide cum instruction cum warranty manual. • The powder coating is done by Burger and Pure Polyester powder with 60 to 70 micron thickness.

DIMENSIONS: - 1620mm (Length) x 365mm (Width) x 1260mm. (Height). • SAFE AREA: - 1.6 x 2.3Mtr. • Mini Leg Press equipment made from “B” Class G.I. pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters • The center pipe is of 80NB made from “B” Class G.I. pipe. • The bottom support of M.S. round plate of Ø250mm & 10mm thick. • The remaining outer frame is of 32NB made from “B” G.I. pipe. • The Seamless MS pipe sleeve provided for easy assembly and dismantling and of 100mm OD and 90mm I.D. This sleeve fitted with SS Bolt of M8 X 16 mm with SS M8 Nylock Nut With Plastic protection caps. • The foundation used for fixing is structure and made from center pipe of G.I. of 80NB . “B” class welded with M.S. round plate of Ø250mm & 10mm thick. Main pipe . Supported with 25 mm X 25mm M.S. angle of 3 mm thickness and 20mm x 40mm CRC . Square pipe of 3mm thickness. • Foundation Protected with Fiber Reinforced Plastic Base Cover on main pipe and of Outer Diameter 200mm and thickness of 2.00mm. • The seats a r e fitted on the outer frames a r e made up of high quality all whether Proof Fiber reinforced Plastic material of size mm 250X 215 mm of thickness 4 mm mounted on M.S. Plate of Size 250mmx200mmx3mm. • The footrests are made from high quality all whether proof Fiber reinforced Plastic 200mm X 120 mm with the support of 250mm X 115mm X 3mm thick MS plate. • The frame of footrests m a d e u p of 25NB “B”class G.I. pipe. • Top cap on main pipe made from Fiber reinforced Plastic material of 2mm thickness • To build structure bushes are used which are made from seamless pipe of 60mm O.D. 5mm thickness. • Pins used are made up of Ø25 mm SAE 8620 bright material and protected with Nylon caps. • The bearings used are of “6205zz” permanent lubricated sealed bearing of reputed Brand • H i g h tensile steel with galvanized nuts and bolts are used for assembly. • A24 cerclips are used for pin locking assembly. • The powder coating done with Pure Polyester Berger made powder with 60 to 70 micron thickness. • All components assembled are of inter changeable, So that it is very easy for future maintenance. • The equipment comes with assembly guide cum instruction cum warranty manual.

DIMENSIONS: - 1200mm (Length) x 870mm (Width) x 980mm. (Height) • SAFE AREA: - 1.5Mtr. X 1.2Mtr. • Rower Equipment made from “B” Class G.I. pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters • The Main frame is of 50NB diameter G.I. Pipe which supported by 80NB G.I. pipe. • The handle frame 25N B is made from “B” class G.I. pipe. • The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “B” class welded with M.S. round plate of Ø250mm& 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. • To join the movement frame to main frame connecting links made up from pipe of 25 NB “B” Class pipe. • To build structure bushes are used which are made from seamless pipe of 60mm O.D. and 6mm thickness as well as 50mm O.D. and thickness of 6mm. • The seats a r e fitted on the outer frames a r e made up of high quality Fiber reinforce Plastic material o f size 250 mm X 220 mm X 10 mm of thickness 4 mm mounted on two M.S. Plate of Size 150mmx150mmx3mm. • Closing caps are made from top quality Fiber reinforced Plastic material which is of 2 mm . thickness. • Pins used of Diameter 17mm are made up from SAE 8620 bright material. • The bearings used are of “6203zz” permanent lubricated sealed bearing of reputed brand. • High tensile steel with galvanized nuts and bolts are used for assembly. • The rubber bushes (Stopper) used to avoid the collision. • A16 cerclips used for assembly of Ø17 mm pins. • The powder coating is done by Pure Polyester powder with 60 to 70 micron thickness.

DIMENSIONS: - 1100mm (Length) x 870mm (Width) x 950mm. (Height) • SAFE AREA: - 1.5Mtr. x 1.5Mtr. • Rower Equipment made from “B” Class G.I. pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters • The Main frame is of 50NB diameter G.I. Pipe and supported with 80NB G.I. pipe. • The handle frame 25N B is made from “B” class G.I. pipe. • The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “B” class welded with M.S. round plate of Ø250mm& 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. • To join the movement frame to main frame connecting links made up from pipe of 25 NB “B” Class pipe. • To build structure bushes are used which are made from seamless pipe of 60mm O.D. and 6mm thickness as well as 50mm O.D. and thickness of 6mm. • The seats a r e fitted on the outer frames a r e made up of high quality Fiber reinforce Plastic material o f size 250 mm X 220 mm X 10 mm of thickness 4 mm mounted on two M.S. Plate of Size 150mmx150mmx3mm. • Closing caps are made from top quality Fiber reinforced Plastic material which is of 2 mm . thickness. • Pins used of Diameter 17mm are made up from SAE 8620 bright material. • The bearings used are of “6203zz” permanent lubricated sealed bearing of reputed brand. • High tensile steel with galvanized nuts and bolts are used for assembly. • The rubber bushes (Stopper) used to avoid the collision. • A16 cerclips used for assembly of Ø17 mm pins. • The powder coating is done by Pure Polyester powder with 60 to 70 micron thickness.

AREA: -1.05Mtr x 0.53Mtr. • HEIGHT: - 1.5 Mtr. • SAFE AREA: - 1.25Mtr x 0.75Mtr. • SkyWalker Equipment made from “B” class G.I. Pipe. • The main frame pipe is 50mm NB made from “B” Class G.I. pipe. • For connecting the handle frame to main pipe 50mm NB “B” Class G.I. pipe is used. • The leg movement frame is of 40mm NB “B” Class G.I. pipe. • The handle pipe is of 25mm NB made from “B” Class G.I. pipe. • The footrests is made from Fiber Reinforced Plastic material, its sizes are 255 X 130 X 5mm. • Closing Caps made from top quality nylon material with 2 mm thickness. • Pins used of Diameter 25mm are made up from SAE 8620 bright material and protected with nylon caps. • The bearings used are “6205zz” &“6203zz” permanent lubricated sealed bearing of reputed brand. • High tensile steel with galvanized nuts & bolts are used for assembly. • The cerclips A24 used for assembly are of Ø25mm. • The cerclips A16 used for assembly are of Ø17mm. • The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “B” class welded with G.I. round plate of Ø250mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. • To build structure bushes are used which are made from seamless pipe of 60mm O.D. And 6mm thickness as well as 60mm diameter solid bar is used. • The equipment comes with assembly guide cum instruction cum warranty manual. • The powder coating is done by Burger and Pure Polyester powder with 60 to 70 micron thickness.

DIMENSIONS: - 700mm (Length) x 400mm (Width) x 1200mm. (Height).  SAFE AREA: - 1Mtr x 6.0Mtr.  Cycle equipment made from “B” class G.I. Pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters.  M.S. round plate of Ø250 mm & 10mm thickness used to for support of whole prime stand assembly. Prime stand is of 40NB G.I. pipe on which handle assembly and FRP Seat is mounted. The seat is made up of heavy Fiber Reinforced Plastic material of size 200mmX250mmX10mm with thickness of 4 mm and it is supported on 130mmX110mmX3mm M.S. Plate.  The handle frame is of 25NB made from “B” Class G.I. pipe.  The paddle frame is of 25NB made from “B” Class G.I. pipe and is having rotary movement with plate Ø300 mm & 10mm thick M.S. plate.  Foot rest is made up of heavy Fiber Reinforced Plastic material of size 255mmX122mmX35mm with thickness of 4mm and it is bolted with S.S. M10 bolt on M.S. plate of size 180mmX110mmX3mm.  The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “B” class welded with M.S. round plate of Ø250 mm& 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness.  Closing Caps made from Nylon material with 3 mm thickness and bolted with M8 S.S. allen bolt.  Pins used of Diameter 25mm are made up from SAE 8620 bright material.  The bearings used are “6205zz” and “6203zz” permanent lubricated sealed bearing of reputed brand.  High tensile steel with galvanized nuts and bolts are used for assembly.  The circlip used for assembly are of A24 and A16 with 1mm thickness.  The powder coating is done w i t h purepolyester powder with 60 to 70 micron thickness.  To build structure bushes are used which are made from seamless pipe of 60mm O.D. and 6mm thickness as well as 60mm diameter solid bar is used.  The equipment comes with assembly guide cum instruction cum warranty manual.

SBR TILE OF 25MM FOR FLOORING PROVIDING AND FIXING OF SBR (STYRENE BUTADENE RUBBER)TILES 0F 25 MM THICKNESS USING GOOD QUALITY ADHESIVE TO PASTE IT ON FLOOR. (AS PER DIRECTION OF OFFICER IN CHARGE.)

PROVIDING AND LAYING OF EPDM (ETHYLENE PROPYLENE DIENE MONOMER) 25MM THICKNESS AND 500 X 500 MM SIZE OF GOOD QUALITY . (AS PER DIRECTION OF OFFICER IN CHARGE.)

PROVISION AND LAYING IN POSITION CEMENT CONCRETE OF SPECIFIED GRADE EXCLUDING AND COST OF CENTERING AND SHUTTERING. ALL WORK UPTO PLINTH LEVEL IN 1:2:4 (1 CEMENT: 2 COARSE SAND : 4 GRADED STONE AGGREGATE 20 MM NOMINAL SIZE) (AS PER DIRECTION OF OFFICER IN CHARGE.)

EARTH WORK IN EXCAVATION BY MECHANICAL MEANS (HYDRAULIC EXCAVATOR)/MANUAL MEANS OVER AREAS (EXCEEDING 30 CM IN DEPTH, 1.5 M IN WIDTH AS WELL AS 10 SQM ON PLAN) INCLUDING GETTING OUT AND DISPOSAL OF EXCAVATED EARTH LEAD UPTO 50 M AND LIFT UPTO 1.5 M (AS PER DIRECTION OF OFFICER IN CHARGE.)

PROVIDING AND LAYING 75 MM THICK COMPACTED BED OF DRY BRICK AGGREGATE OF 40 MM THICK NOMINAL SIZE INCLUDING SPREADING,WELL RAMMING, CONSOLIDATING AND GROUTING WITH JAMUNA SAND,INCLUDING FINISHING SMOOTH ETC. COMPLETE (AS PER DIRECTION OF OFFICER IN CHARGE.)

PROVIDING AND LAYING IN POSITION CEMENT CONCRETE OF SPECIFIED GRADE EXCLUDING THE COST OF CENTERING AND SHUTTERING - ALL WORK UP TO PLINTH LEVEL :1:5:10 (1 CEMENT : 5 COARSE SAND (ZONE-III): 10 GRADED STONE AGGREGATE 40 MM NOMINAL SIZE) (AS PER DIRECTION OF OFFICER IN CHARGE.)

PROVIDING AND LAYING AT OR NEAR GROUND LEVEL FACTORY MADE KERB STONE OF M-25 GRADE CEMENT CONCRETE IN POSITION TO THE REQUIRED LINE, LEVEL AND CURVATURE, JOINTED WITH CEMENT MORTAR 1:3 (1 CEMENT: 3 COARSE SAND), INCLUDING MAKING JOINTS WITH OR WITHOUT GROOVES (THICKNESS OF JOINTS EXCEPT AT SHARP CURVE SHALL NOT TO MORE THAN 5MM), INCLUDING MAKING DRAINAGE OPENING WHEREVER REQUIRED COMPLETE ETC. AS PER DIRECTION OF ENGINEER-IN-CHARGE (LENGTH OF FINISHED KERB EDGING SHALL BE MEASURED FOR PAYMENT). (PRECAST C.C. KERB STONE SHALL BE APPROVED BY AS PER DIRECTION OF OFFICER IN CHARGE.)

PROVIDING AND LAYING 60MM THICK FACTORY MADE CEMENT CONCRETE INTERLOCKING PAVER BLOCK OF M -30 GRADE MADE BY BLOCK MAKING MACHINE WITH STRONG VIBRATORY COMPACTION, OF APPROVED SIZE, DESIGN & SHAPE, LAID IN REQUIRED COLOUR AND PATTERN OVER AND INCLUDING 50MM THICK COMPACTED BED OF COARSE SAND, FILLING THE JOINTS WITH LINE SAND ETC. ALL COMPLETE AS PER THE DIRECTION OF ENGINEER-IN-CHARGE.

Supplying and stacking of good earth at site including royalty and carriage upto 5 km lead complete (earth measured in stacks will be reduced by 20% for payment).

Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately).

Carriage of good earth by Manual Labour including loading, unloading and stacking for lead less than 0.50 KM

SUPPLYING AND STACKING OF RED BAJRI AT SITE.

SUPPLYING AND SPREADING OF SAND IN LAWN AREA, INCLUDING WATERING, MIXING AND DRESSINGCOMPLETE. (AS PER DIRECTION OF OFFICER IN CHARGE.)

STEEL WORK IN BUILT UP TUBULAR(HOT FINISHED WELDED TYPE ROUND, SQUARE, RECTANGULAR HOLLOW TUBES ETC.) TRUSSES, SEATING ARRANGEMENT ETC INCLUDING CUTTING, HOISTING, FIXING IN POSITION AND APPLYING A PRIMING COAT OF APPROVED STEEL PRIMER, INCLUDING WELDING AND BOLTED WITH SPECIAL SHAPED WASHERSETC. COMPLETE (AS PER DIRECTION OF OFFICER IN CHARGE.)

12MM CEMENT PLASTER OF MIX : (A) 1:6 (1 CEMENT : 6 FINE SAND) (AS PER DIRECTION OF OFFICER IN CHARGE.)

BRICK WORK WITH COMMON BURNT CLAY F.P.S. (NON-MODULAR) BRICKS OF CLASS DESIGNATION 7.5 IN FOUNDATION AND PLINTH IN. (A) CEMENT MORTAR 1:6 (1 CEMENT : 6 COARSE SAND). (AS PER DIRECTION OF OFFICER IN CHARGE.)

DEMOLISHING BRICK WORK IN CEMENT MORTAR MANUALLY/ BY MECHANICAL MEANS INCLUDING STACKING OF SERVICEABLE MATERIAL AND DISPOSAL OF UNSERVICEABLE MATERIAL WITHIN 50 METRES LEAD (AS PER DIRECTION OF OFFICER IN CHARGE.)

PROVIDING AND FIXING G.I. CHAIN LINK FABRIC FENCING OF REQUIRED WIDTH IN MESH SIZE 50X50 MM INCLUDING STRENGTHENING WITH 2 MM DIA WIRE OR NUTS, BOLTS AND WASHERS AS REQUIRED COMPLETE AS PER THE DIRECTION OF ENGINEER-IN-CHARGE. MADE OF G.I. WIRE OF DIA 4 MM

PROVIDING AND FIXING CONCERTINA COIL FENCING WITH PUNCHED TAPE CONCERTINA COIL 600 MM DIA 10 METRE OPENABLE LENGTH ( TOTAL LENGTH 90 M), HAVING 50 NOS ROUNDS PER 6 METRE LENGTH, UPTO 3 M HEIGHT OF WALL WITH EXISTING ANGLE IRON 'Y' SHAPED PLACED 2.4 M OR 3.00 M APART AND WITH 9 HORIZONTAL R.B.T. REINFORCED BARBED WIRE, STUD TIED WITH G.I. STAPLES AND G.I. CLIPS TO RETAIN HORIZONTAL, INCLUDING NECESSARY BOLTS OR G.I. BARBED WIRE TIED TO ANGLE IRON, ALL COMPLETE AS PER DIRECTION OF ENGINEER-IN-CHARGE, WITH REINFORCED BARBED TAPE(R.B.T.) / SPRING CORE (2.5MM THICK) WIRE OF HIGH TENSILE STRENGTH OF 165 KG/ SQ.MM WITH TAPE (0.52 MM THICK) AND WEIGHT 43.478 GM/ METRE (COST OF M.S. ANGLE, C.C. BLOCKS SHALL BE PAID SEPARATELY)

SUPPLY OF SIGN BOARDS OF 0.91 X 0.61M SIZE WITH SUPPORT LENGTH OF 3000 MM. MANUFACTURING, SUPPLYING AND FIXING OF RETRO REFLECTIVE SIGN BOARDS MADE OF 2 MM THICK ALUMINUM SHEET FACE TO BE FULLY COVERED WITH HIGH INTENSITY ENCAPSULATED TYPE HEAT ACTIVATED RETRO REFLECTIVE SHEETING CONFORMING TO TYPE – IV OF ASTM-D 4956-01 IN GREEN AND SILVER WHITE INCLUDING SUBJECT MATTER, MESSAGE (BILINGUAL(, SYMBOL AND BORDERS ETC AS PER IRC: 67-2001, PASTED ON SUBSTRATE BY AN ADHESIVE BACKING WHICH SHALL BE ACTIVATED BY APPLYING HEAT AND PRESSURE CONFORMING TO CLASS -2 OF ASTM-D-4956-01 AND FIXING THE SAME WITH SUITABLE SIZED ALUMINUM ALLOY RIVETS @ 20 CM C/C TO BACK SUPPORT FRAME OF M.S ANGLE IRON OF SIZE 35X35X5 MM AND M.S FLAT OF 25X5 MM ALONG WITH THEFT RESISTANT MEASURES, MOUNTED AND FIXED WITH 2 NOS. CLAMP OF MLS FLATS OF SIZE 25X5 MM TO A VERTICAL POST OF 3 MTR HEIGHT MADE UP OF MSL PIPE OF 60 MM N.B WELDED WITH TWO HOLD FAST OF M.S ANGLE 25X25X3MM OF 30CM LENGTH EACH AT BOTTOM AND INCLUDING MAKING HOLES IN PIPES, ANGLES, PROVIDING & FIXING M.S MESSAGE PLATE OF REQUIRED SIZE, STEEL WORK TO BE PAIRED WITH TWO OR MORE COATS OF SYNTHETIC ENAMEL PAINT OF REQUIRED SHADE AND OF APPROVED BRAND AND MANUFACTURE OVER A PRIMING COAT OF ZINC CHROMATE YELLOW PRIMER (VERTICAL POST TO BE PAINTED IN BLACK/WHITE/GREY COLOR) BACKSIDE OF ALUMINUM SHEET TO BE PAINTED WITH TWO OR MORE COATS OF EPOXY PAINT OVER AN APPROPRIATE PRIMING COAST INCLUDING ALL LEADS AND LIFTS ETC. COMPLETE AS PER DRAWING, SPECIFICATION AND DIRECTION OF OFFICER-IN CHARGE.

SUPPLY AND FIXING OF SIGN BOARDS OF 1.22 X 1.83M SIZE WITH WITH SUPPORT LENGTH OF 4570 MM. MANUFACTURING, SUPPLYING AND FIXING OF RETRO REFLECTIVE SIGN BOARDS MADE OF 2 MM THICK ALUMINUM SHEET ,FACE TO BE FULLY COVERED WITH HIGH INTENSITY ENCAPSULATED TYPE HEAT ACTIVATED RETRO REFLECTIVE SHEETING CONFORMING TO TYPE –IV OF ASTM-D 4956-01 IN GREEN AND SILVER WHITE INCLUDING SUBJECT MATTER, MESSAGE(BILINGUAL),SYMBOL AND BORDERS ETC AS PER IRC:67-2001 , PASTED ON SUBSTRATE BY AN ADHESIVE BACKING WHICH SHALL BE ACTIVATED BY APPLYING HEAT AND PRESSURE CONFORMING TO CLASS -2 OF ASTM-D-4956-01 AND FIXING THE SAME WITH SUITABLE SIZED ALUMINUM ALLOY RIVETS @ 20 CM C/C TO BACK SUPPORT FRAME OF M.S ANGLE IRON OF SIZE 35X35X5 MM AND M.S FLAT OF 25X5 MM ALONG WITH THEFT RESISTANT MEASURES, MOUNTED AND FIXED WITH 2 NOS CLAMP OF M.S FLATS OF SIZE 25X5 MM TO A VERTICAL POST OF 4.57 MTR HEIGHT MADE UP OF M.S PIPE OF 10 MM N.B WELDED WITH TWO HOLD FAST OF M.S ANGLE 25X25X3MM OF 45CM LENGTH EACH AT BOTTOM AND INCLUDING MAKING HOLES IN PIPES, ANGLES ,PROVIDING & FIXING M.S MESSAGE PLATE OF REQUIRED SIZE ,STEEL WORK TO BE PAINTED WITH TWO OR MORE COATS OF SYNTHETIC ENAMEL PAINT OF REQUIRED SHADE AND OF APPROVED BRAND AND MANUFACTURE OVER A PRIMING COAT OF ZINC CHROMATE YELLOW PRIMER (VERTICAL POST TO BE PAINTED IN BLACK/WHITE/GREY COLOR)BACKSIDE OF ALUMINUM SHEET TO BE PAINTED WITH TWO OR MORE COATS OF EPOXY PAINT OVER AN APPROPRIATE PRIMING COAT INCLUDING ALL LEADS AND LIFTS ETC. COMPLETE AS PER DRAWING ,SPECIFICATION (AS PER DIRECTION OF OFFICER IN CHARGE).

PROVIDING AND FIXING OF S.S. SIGN BORDS OF ( GRADE 304) 0.45M X 0.91M SIZE WITH 2 SUPPORTS OF LENGTH- 0.91M S.S PAPE FIXING OF RETRO REFLECTIVE SIGN BOARDS MADE OF 4 MM THICK ALUMINUM SHEET ,FACE TO BE FULLY COVERED WITH HIGH INTENSITY ENCAPSULATED TYPE HEAT ACTIVATED RETRO REFLECTIVE SHEETING CONFORMING TO TYPE –IV OF ASTM-D 4956-01 IN GREEN AND SILVER WHITE INCLUDING SUBJECT MATTER, MESSAGE(BILINGUAL) ,SYMBOL AND BORDERS ETC AS PER IRC:67-2001 , PASTED ON SUBSTRATE BY AN ADHESIVE BACKING WHICH SHALL BE ACTIVATED BY APPLYING HEAT AND PRESSURE CONFORMING TO CLASS -2 OF ASTM-D-4956-01 AND FIXING THE SAME WITH SUITABLE SIZED ALUMINUM ALLOY RIVETS COST INCLUDING MAKING HOLES IN PIPE PROVIDING AND FIXING MASSAGE PLATE OF REQUIRES SIZE FIXING OF BASE FRAME OF BOARD WITH EARTH WORK IN EXCAVATION OF (0.2X0.2X0.5), PCC OF SPECIFIED GRADE EXCLUDING THE COST OF CENTERING AND SHUTTERING - ALL WORK UP TO PLINTH LEVEL : 4.1.2 1:1½:3 (1 CEMENT: 1½ COARSE SAND (ZONE-III) : 3 GRADED STONE AGGREGATE 20 MM NOMINAL SIZE) OF SIZE 20X.20X.1 , C.C SPECIFIED GRADE EXCLUDING THE COST OF CENTERING AND SHUTTERING - ALL WORK UP TO PLINTH LEVEL : 4.1.2 1:1½:3 (1 CEMENT: 1½ COARSE SAND (ZONE-III) : 3 GRADED STONE AGGREGATE 20 MM NOMINAL SIZE) INCLUDING THE COST OF PAINTING WITH TWO OR MORE COATS OF EPOXY PAINT IN GREY COLOUR ON THE BACK SIDE OF ALUMINIUM SHEET INCLUDING APPROPRIATE PRIMING COAT. THE RATE INCLUDES THE COST OF ROUNDING OFF THE CORNERS, LOWERING DOWN THE STRUCTURAL FRAME WORK FROM THE GANTRY, FIXING AND ERECTING THE SAME IN POSITION ALL COMPLETE AS PER DRAWINGS, SPECIFICATION (AS PER DIRECTION OF OFFICER IN CHARGE.)

Radhey Mohan International

Greenz

Sansun industries pvt ltd

Grand Slam Fitness Private Limited