REPAIR REPLACEMENT OF OLD UNSV LED SECURITY LIGHT FITTINGS LT UG CABLE BRACKETS POLES LT INDOOR PANEL OUTDOOR FEEDER PILLAR BOX MCCB AND OTHER CONNECTED WORKS AT PALAMPUR MIL STN

Amount

Taking down unsv security light fitting, Flood light, and decorative LED light fitting of any wattage from poles / roof at any position and dismentling the light fitting and replace the unsv driver,PCB card and reassemble at the existing bracket and refixing the same complete all as directed by Engr-in-Charge. (Note LED driver and PCB card will be measuredand paid seperately as supply only).

Supply only LED driver suitable for LED street light fittings of 45 watt complete

Supply only LED driver suitable for LED street light fittings of 60 watt complete

Supply only LED driver suitable for LED street light fittings of 90 watt complete

Supply only LED driver suitable for LED street light fittings of 120 watt complete

Supply only PCB Card suitable for Multi LED Light Fitting of capacity 45 Watt complete all as specified and as directed.

Supply only PCB Card suitable for Multi LED Light Fitting of capacity 60 Watt complete all as specified and as directed.

Supply only PCB Card suitable for Multi LED Light Fitting of capacity 90 Watt complete all as specified and as directed.

Supply only PCB Card suitable for Multi LED Light Fitting of capacity 120 Watt complete all as specified and as directed.

Excavation in trenches in any type of soil not exceeding 1.5 mtr in depth and not exceeding 1.5 mtr wide for laying of cables, erection of poles,struts, stays etc and getting out all as specified and as directed by Engr-In-Charge.

All as per item No 10 above here in before but in hard/PCC/Floor/road

Returning, filling in including spreading, levelling,watering and well ramming excavated soil in layers not exceeding 25 cm thick each , filling back in trenches after cables have been laid and tested, poles,stays,struts hane been erected and tested complete all as specified.

Removal of excavated surplus soil to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 metre above the starting point complete all as specified.

M&L for sand cushioning to under ground cables 8 cm thick before laying the cable and 15 cm, thick after laying, stretching and testing the cable complete all as specified and directed by Engr-in-Charge.

M&L for laying in trenches burnt brick sub class 'B' for cable protection laid adjacent to each other length wise perpendicular to the central axis of cable complete all as specified.

Taking out from trenches/floors/road/wall/pipe/pole LT cable of any size/description and removing from site incl making good the disturbed surfaces to match with existing surface all as directed.

Supply & laying of UG cable XLPE insulated armoured heavy duty elect cable with stranded aluminium conductor 1100 volts grade cross section area 120 Sqmm 3.5 core laid in trenches/ fixing on panels/walls/poles or passing through pipe including connecting with suitable lugs, glands, nuts and bolts and testing complete all as specified and directed.

All as per item No. 17 above but of cross sectional area 95 Sqmm, 3.5 core.

All as per item No. 17 above but of cross sectional area 70 Sqmm, 3.5 core.

All as per item No. 17 above but of cross sectional area 50 Sqmm, 3.5 core.

All as per item No. 17 above but of cross sectional area 35 Sqmm, 3.5 core.

All as per item No. 17 above but of cross sectional area 25 Sqmm, 3.5 core.

All as per item No. 17 above but of cross sectional area 16 Sqmm, 4 core.

All as per item No. 17 above but of cross sectional area 10 Sqmm, 4 core.

All as per item No. 17 above but of cross sectional area 10 Sqmm, 2 core.

Supply & fixing 50W LED flood light fitting IP66 Powder coated pressure die cast aluminium High power LED street light with heat resistant toughened glass with lens, complete with all accessories duly prewired and suitable fixing arragement for mounting on existing MS frame bracket including connecting the fitting complete all as specified and directed including taking down old unsv flood light

M&L for work confirming to Fe-410-O or Fe-310-O as in cross arms, support, bracings, stiffeners, clamps channels fabricated from structural steel including nuts, bolts and washers welding, bending cold or hot drilling holes for bolts in any shape or size all as directed including two coats of aluminium paint over a coating of red oxide primer all as directed by Engr-In-Charge.

M&L for Cable route indicator showing "LT Cable" and rout of cable with arrow made of CI in suitable eliptical/round shape and fixed on angle iron 40x40x6mm, 800mm long painted in Blue Colour with two coats of synthetic enamel paint cover a coat of red oxide primer duly embaded in PCC block (0.40x0.40x0.40)mtr including in ground and 0.15mtr above ground lable complete all as directed and specified.

Supply and fix cable jointing kit for 1.1 KV grade cable for straight through joint complete with Jointing material (Epoxy Based) and accessories suitable for 3½/ 4 core XLPE armoured Al conductor cable of size 25 to 50 sq mm complete all as specified and as directed

Supply and fix cable jointing kit for 1.1 KV grade cable for straight through joint complete with Jointing material (Epoxy Based) and accessories suitable for 3½/ 4 core XLPE armoured Al conductor cable of size 70 to 95 sq mm complete all as specified and as directed.

M&L for laying GI Tubing med grade 50mm dia for cable potection in road/floor complete all as specified .

M&L for laying GI Tubing med grade 80mm dia for cable potection in road/floor complete all as specified .

M&L for Plain Cement Concrete 1:2:4 type B-1 using 20mm graded stone aggregate for coping around poles,earth pit ,including provision of necessary form work, finishing even and smooth without using extra cement complete all as specified and as directed by Engr-in-Charge.

M & L Plain Cement Concrete 1:3:6 type C2 using 40mm graded stone aggregate as in road cutting filling, foundation, fencing post , struts etc. complete all as specified and directed by Engr - in Charge.

Supply and fixing in replacement of MCCB 400 Amp rating,4-pole 415V, 50 Hz breaking capacity 36 KA, Adjustable & fixed magnetic setting type

Supply and fixing in replacement of MCCB 250 Amp rating,4-pole 415V, 50 Hz breaking capacity 36 KA, Adjustable & fixed magnetic setting type.

Supply and fixing in replacement of MCCB 200 Amp rating,4-pole 415V, 50 Hz breaking capacity 25 KA, Adjustable & fixed magnetic setting type.

Supply and fixing in replacement of MCCB 160 Amp rating,4-pole 415V, 50 Hz breaking capacity 25 KA, Adjustable & fixed magnetic setting type.

Supply and fixing in replacement of MCCB 125 Amp rating,4-pole 415V, 50 Hz breaking capacity 16 KA, Adjustable & fixed magnetic setting type.

Supply and fixing in replacement of MCCB 100Amp rating,4-pole 415V, breaking capacity 16KA.

Supply and fixing in replacement of MCCB 63Amp rating,4-pole 415V, breaking capacity 16KA.

Earthing complete with galvanised steel earth plate electrode 60cmX60cmX6.0mm thick, buried directly in ground (earth pit not less than 2.25mtr deep below normal ground level) with top edge of the plate not than 1.5mtr below normal ground level connected to GI earth strip of size 32x6mm dia by means of bolts, nuts, check nuts and washers of galvanised iron complete earth pit of PCC M-10(Nominal mix) using 20mm graded stone aggregate, 50mm thick earth pit cover of RCC M-15 (Nominal mix) using 20mm graded stone aggregate with MS TMT reinforcement bar of 8mm dia @ 150mm centre to centre both ways, MS handle 10mm dia made to shape, PGI funnel, wire mesh and 20mm bore GI water pipe medium grade and 40mm bore medium grade GI pipe for protection of earth strip from plate to main switch board, common salt, charcoal dust including testing on completion complete all as specified and as directed all as shown in electrical plate No. 3 including testing on completion and making good the disturbed surfaces of wall floors etc without claiming extra cost all as directed by Engr-in-Charge. (Note: GI strip & GI pipe beyond 7.5Mtr length from earth electrode shall be measured and paid separately).

M&L for removal green vegetation and dressing around the plinth/PCC hardstanding up to 1.5 mtr of sub stations and panels etc including disposal of vegitation /material up to 50 mtr distance from the site and levelling/surfacing the ground all as specified and as directed by Engr-in-Charge.

Supply and fix MS Chequred plate 6.0 mm thick sheet having with Hook, and painting it with one coat of black paint suitable for cable duct cover in power huse and sub stn complete all as specified and directed

Supply and fixing in replacement voltmeter for LT panel Square dial of size 96x96mm digital type complete all as specified and as directed.Make : AE/Rishabh(Note: Existing meter analough type and large in size, hence any modification in the wiring,and panel sheet enclosure is deemed to be inclusive in the scope of work).

Supply and fixing in replacement Ammeter for LT panel Square dial of size 100 mm digital type complete all as specified and as directed.Make : AE/Rishabh (Note: Existing meter analough type and large in size, hence any modification in the wiring,and panel sheet enclosure is deemed to be inclusive in the scope of work).

Supply and fixing in replacement indicator lamp assembly in red,yellow & blue colour for LT panels complete all as specified and as directed.

Supply and spread graded coarse aggregate of 40mm to 63mm nominal mixed size around outdoor transformer and two/four pole structure /Panel after cleaning and leveling of work area complete all as specified and directed.

Supplying and fixing of Off-load type Changeover switch 100 Amp, 4-pole, 415 volt, with enclosure type complete all as specified and as directed. Make: Havells/L&T/BCH/Schneider

Supplying and fixing of Off-load type Changeover switch 125 Amp, 4-pole, 415 volt, with enclosure type complete all as specified and as directed. Make: Havells/L&T/BCH/Schneider

M&L for HDPE Double Wall Corrugated pipe of size 63mm outer dia and 50mm inner dia confirming to IS:14930 Part-II including necessary pipe fittings such as couplers, end caps, bend etc. including fixed to wall/roof /pole/trench as required with suitable clamps for cable protection complete all as specified and directed.

M&L for HDPE Double Wall Corrugated pipe of size 90mm outer dia and 75mm inner dia confirming to IS:14930 Part-II including necessary pipe fittings such as couplers, end caps, bend etc. including fixed to wall/roof /pole/trench as required with suitable clamps for cable protection complete all as specified and directed.

Supply,install,testing and commissioning of CPRI approved factory made LT feeder piller box outdoor type with double doors provided with locking arrangements dust, vermin and water proof made out of 3.15 mm thick CRCA sheet duly compartmentalized inside panel with 2mm thick CRCA sheet powder coated with back door detachable fixed with nuts, bolts and washers and front doors openable type fitted with hinges and knobs/locks. Panel is to be placed on angle (size 50x50x6mm) frame duly painted with two coats of synthetic enamel paint over a coat of primer to the portion visible to eye supported on 04 legs 750mm long each duly 450 mm grouted in PCC blocks of type 1:2:4 type B-1and 300mm above ground level for entry of cables suitable for 3-phase, 4-wire, 50Hz,415 volts,with and including necessary incoming and out going cable connection with proper size aluminium lugs, nut bolts etc including the folowing complete all as specified and as directed:- (a) MCCB 250 Amp,4P, 36KA (I/C for Main Supply) - 01 Nos (b) MCCB, 125A, 25 KA, 3 Pole (OG) 03Nos ( c) MCCB, 100A, 25 KA, 3 Pole 2Nos [d] LED type AC 220V Phase Indicators RYB, Make : C&S/Schnieder/BCH - 02 Set (e] Aluminium strip bus bars with heat shrinkable type colour code PVC insulation sleeves 400 Amps capacity TPN mounted on epoxy insulators - 02Set Voltmeter, Amper meter,indicator lamps , CT coi 100/5-01 set. (v) Aluminium Bus bar 4 strip -400 Amps capacity. (vi)Internal wiring of panel board with copper cable single core of sutable size and incl 03 Nos bakelite control fuses. [g] Danger notice plate for LT with conventional skull and bones duly rivetted/pasted to the panel board door Note :- The contractor will approved the panel drawing before incorporate in the work and should be CPRI approved

S& F LT cubical panel outdoor kiosk type with Aluminium bus bar 3 pin 4 wire metering and comprising of following :- (i) MCCB TPN63A -01 No for I/C (ii) MCCB SPN 63 Amp -01 for O/G (iii) MCB SPN 32 Amp -02 Nos complete all as specified

Dismentling all existing cable connection from the fedder pillar box with nuts,bolts, washer etc and scrapping down old paint of existing feeder pillor box inside end out side complete and spray painting with two coats of synthetic enamel paints(red post office colour ) over coat of red oxide primer complete .

Supply , fixing, testing and commissioning of factory made LT panel board made out of CRCA sheet 3.15mm thick outdoor type totally enclosed with front opening hinged doors with canopy sloped top projected and floor mounted , weather and water proof as per IS-8623 with necessary locking arrangement all as specified and directed including painting with two coats of synthetic enamel paint over a coat of red oxide primer , internal electric connections as required suitable to accommodate the following :- (i) MCCB 100 Amp TPN -01 No( I/C), (ii) MCCB 63A -02 Nos (O/G) , Al bus bar, indication lamps -03 Nos

S&F glow sign boards made out of acraylic sheet 2 mm thick fitted on front side of the box and GI sheet 24 SWG for making installation mounted on a 25x25x4mm angle iron frame including tube light fitting of suitable size prewired complete with stranded accessories size of board is 150cmx0.60cmx0.15cm duly written in bold capital letters of size as suitable for sign board (Font as explained and approved by engineer in charge ) including necessary cable connection for supply to board complete as specified and directed by the engineer in charge. (Note Sign board and name which to be written on board shall got approved from the engineer in charge before execution. as per Appx att)

Supply and laying or fixing or passing through pipe, 1100 volts grade heavy duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed 10 sq. mm 2 Core nominal cross section in service connections

Supply and laying or fixing or passing through pipe, 1100 volts grade heavy duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed 16 sq. mm 4 Core nominal cross section in service connections

S&F in repair/replacement LED decorative street Light asthetically designed with aluminium enclosure ,suspended mounting arrangement with IP65 of capacity 40 Watt complete all as specified and directed by Engr in Charge

M&L for bending & shaping of 40 mm dia galvanised iron pipe light grade over all length 0.60 mtr including necessary clamps, brackets ,nut and bolts etc to fixed on wall/pole as per site requirement including fixing on pole with light fittings.

S & F PVC Three core copper conductor 2.5 Sqmm cable alongwith PVC pipe for protection for connection from junction box to LED fitting complete .

Supply and fix in repairs time digital switch with built in PCB for street light complete all as specified

Trimming / chopping and cuting of branches each tree of any grith which are coming across/around the security light pole /fitting up to 3 meter all sides of the poles etc as required and removing the same from site of work complete all as directed by Engr in charge.

Material and labour for Painting to 9 mtr long steel tubular security/street light pole with Black & White strip 30 Cm a part alternaterly up to 1.5Mtr height from ground level with synthetic enmel paint with two coats of aluminium paint after removal of all dust from outer surface of the pole including numbering of pole complete all as directed by Engr-in-Charge.

S&F LED Tricolor (Orange/White/Green) 3 in 1 Tiranga Single Strip Light with 18 Meter length,LED Decorative Pole Lighting Etc-Pack of 1,IP 65 rating withstand harsh weather poof complete all as specified and directed by Engr in charge.

Supply, fixing & testing 45W LED street light fitting IP66 Powder coated pressure die cast aluminium High power LED street light with heat resistant toughened glass with lens embdded PC cover complete with all accessories duly prewired and suitable fixing arragement for mounting on existing MS frame bracket including connecting the fitting complete all as specified and directed including taking down .(Make- Philips Cat NoBRP031 LED45 CW / WW MR PSU GR DX Bajaj Cat Part No ENXT P 54L WH CR PC SD/Havells Cart Part No ENDURASUNDOWNSL45WLED765PASYBOTG Note : GI pipe bracket and clamps if required shall be measured and paid separately.

Supply, fixing & testing 60W LED street light fitting IP66 Powder coated pressure die cast aluminium High power LED street light with heat resistant toughened glass with lens, complete with all accessories duly prewired and suitable fixing arragement for mounting on existing MS frame bracket including connecting the fitting complete all as specified and directed including taking down .(Make- Philips Cat No BRP032 LED60 CW / WW SLR GR PSU Bajaj Cat Part No ENXT P 72L WH CR PC SD/Havells Cat part No ENDURAPEARLNEOSL 60WLED757PASYTOPCAST Note : GI pipe bracket and clamps if required shall be measured and paid separately.

Supply, fixing & testing 90W LED street light fitting IP66 Powder coated pressure die cast aluminium High power LED street light with heat resistant toughened glass with lens, complete with all accessories duly prewired and suitable fixing arragement for mounting on existing MS frame bracket including connecting the fitting complete all as specified and directed including taking down .(Make- Philips Cat No BRP032 LED60 CW / WW SLR GR PSU Bajaj Cat Part No ENXT P 72L WH CR PC SD/Havells Cat part No ENDURAPEARLNEOSL 60WLED757PASYTOPCAST Note : GI pipe bracket and clamps if required shall be measured and paid separately.

Supply and fix in replacement of 120 Watt LED flood light ( Red,Green and Worm White colour) fitting made up of Pressure die-cast aluminium alloy housing with toughened glass, IP65 protection and impact resistance of IK07 and individual high power LEDs with secondary optics having system lumen efficiancy ≥100 lm/W, Inbuilt potted electronic LED driver with APFC (SMPS based constant current supply), lower THD, Open Circuit protection, Over Voltage protection, Surge Voltage protection & other safety test as per IS 15885 Part-2/Sec 13 and BIS complying including surface mounting using adjustable MS cradle of thickness 5 mm provided with the fixture including taking down existing unserviceable flood light fitting of any description complete all as specified and directed by Engineer-in-Charge. Note :- LM 79 test report, LM 80 report with minimum 9000 hrs testing to support 50K life TTC and dirver NABL accreditated report shall be submitted before execution of work to the Engineer - in - charge.

Supply and fixing outdoor type control with Photo Sensitive smart sensor LED street light fitting 70 Watt 230 V AC outdoor type & high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impactand corrosion resistant including thermal management in multiple optics & suitable connection with photoelectric sensor complete with IP 65/66 protection complete as specified

S&F LED Bollard 5 Watt -500mm with IP-65 Protection 220 Volt 50 Hz, including taking down unserviceable Light Fitting of any description, complete all as specified and as directed.

Supply & Fix in repairs LED Post top lantern of 1X40 Watt with die cast aluminium spigot and lid cover, high efficient LEDs and clear acrylic cover IP-65, complete all as specified and directed.

Supply & Fixing repairs cable junction box made of thermoplastic, halogen free, weather proof with metric Knock outs for cable entry including four/five pole terminals and cable entry glands for incomming, out going and connection cable with protection grade IP-66/67 of size 205x255x112 mm and suitable for LT under ground cable any size/capacity including bracing clamp,bolts,nuts & washers. complete all as specified

Supply and fixing in replacement LT panels door made of MS sheet to 16 SWG including fabrication to required shape and size by cutting /bending /welding including butt hinges and locking arrangement handle for doors as directed with two coats of synthetic enamel paint on both side over a coat of red oxide primer as directed by Engr in charge

BHARDWAJ BUILDERS (BID ID -3345121)

M/S MALHI CONSTRUCTIONS (BID ID -3354081)

somyaenterprises (BID ID -3346114)