SPECIAL REPAIRS TO BLDG NO T-66, T-80, T-33 AND P-03 UNDER GE MISAMARI

Amount

Demolition Cement Concrete (un-reinforced) in ground floors and pavings n exc 15 cm thickness (below of above ground level) complete all as specified and as directed.

Demolition Cement Concrete (reinforced) of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

Demolition of Brick Work built in Cement Mortar including all Quoins, Arches, Pillars, etc. of any descriptions, complete all as specified and as directed. .

Dismantling floor hearth or wall tiling incl cement mortar bedding but not backing and removing rubbish off the premises complete all as specified and as directed.

Dismantling boarding of any description and any position fixed with nails,complete all as specified and as directed.

Taking down Chowkat or Frame (without taking off shutter from the frame) not exc. 1.50 Sqm Each, complete all as specified and as directed. .

Taking down Chowkat or Frame (without taking off shutter from the frame) exc. 1.50 Sqm but not exc 4.00 Sqm Each, complete all as specified and as directed. .

Taking down shutters of any description not exc 1 sqm each complete all as specified and as directed.

Refixing only in same opening after resecuring or easing and adjusting of shutters of any description n exc 1sqm each complete all as specified and as directed.

Dismantling Wall and Ceiling Boards (Fibre, Pulp, Insulation etc.) or Eaves/Insulation Board/Slab/Blankets of any thickness, etc. including cover fillets of any descrip-tion, complete all as specified and as directed. .

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc., complete all as specified and as directed.

Desmentling Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings, complete all as specified and as directed. .

Dismantling structural steel work including doors, gates but excluding framed truss etc., complete all as specified and as directed.

Dismantling of timber scantling 40 sqcm and over in section in any position framed work complete all as specified and as directed.

Dismantling Timber Fillet, Rails, Posts, Rafter, Purlins, etc. under 40 Sq Cm in Section in Unframed Work, complete all as specified and as directed. .

Taking down Cement Plaster of any description on brick walls, concrete surfaces including racking out joints, hacking for key, scrubbing down with water, remove dust, debries/rubbish etc., complete all as specified and as directed. .

Demolition of reed, lathing, single or double, including battens and plaster or chicken wire lathing complete all as specified and as directed.

M & L for PCC 1:3:6 type C-2 using 40mm graded aggregate as in foundation filling and mass concrete, complete all as specified and as directed.

M & L for PCC 1:4:8 type D-2 using 40mm graded aggregate as in foundation filling and mass concrete, complete all as specified and as directed.

M & L for 100mm thick PCC 1:3:6 Type C2 using 40mm graded aggregate as in sub base complete all as specified and as directed.

M&L for 75mm thick PCC 1:3:6 type C2 using 40 mm graded stone aggregate as in plinth protection/hard standing including finished surface finished even and smooth without using extra cement complete all as specified and as directed.

M&L for 75mm thick 1:4:8 type D2 using 40mm graded stone aggreage as in sub base/path finished even and smooth without using extra cement complete all as specified and directed.

M&L for concrete bed to drain pipes incl packing under and haunching against the sides of pipes after they are laid and tested in cement concrete (1:3:6) type C2 (using 40 mm graded aggregate) complete all as specified and as directed.

M&L for reinforced precast cement concrete (1:2:4) type B1 (using 20 mm graded stone aggregate) as in manhole cover slab and set in CM (1:4) complete all as specified and directed.

M&L for RCC types A1 1:1.5:3 (20mm graded aggregate) as in beam, cantilivers, bressummers, lintels over 1.5m span complete all as specified and as directed.

M & L for RCC 1:2:4 type B-1,(using 20mm graded crushed stone aggregate) as in slab supported on walls, beam and column in floors , roofs, landing deck slab etc with and incl used and waster of formwork whereever required complete all as specified and as directed.

M&L for reinforced Cement Concrete 1:2:4 type-B1 (20mm graded aggregate) in Cover Slab of Manholes, Septic Tanks, etc., set in Cement Mortar 1:4 including necessary forms, moulds, etc., complete all as specified and as directed.

S & F mild steel TMT deformed bar 10mm dia over cut to length bent to shape required including cranking bending and binding with and including mild steel wire annealed not less than 0.9mm dia complete all as specified and as directed.

Mild steel bars 5mm and over upto and including 10mm dia in stirrups spaces and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and as directed.

S&F of Structural steel, rolled section as in main and cross beams, hips and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates conforming to Fe-410 W (Gde-E-250) complete all as specified and as directed.

M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick Flat, rough finished surface complete all as specified and as directed. .

M & L for machine pressed precast concrete interlocking paver block any shape and size conforming to IS -15658 - 2006 of 60 mm thickness, M-35 Grde set, jointed and pointed in neat cement slurry in floors with cement pigment laid over 50mm thick sand cushion and incl demolition of existing floor of any description complete all as specified and as directed.

M & L for Chequered cement concrete tiles 20cm x 20cm x 20-22mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement pigment and pigment incl 15mm thick screed bed in CM 1:6, complete all as specified and as directed.

M&L for vitrified tiles (DURA STONE) heavy duty of size 300x300x8 to 9mm thick as in footpath set and jointed in neat cement slurrty and pointed in grey cement complete all as specified and as directed.

S & F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S & F Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F GI powder coated snap grid frame work for false ceiling comprising perimeter channel of 0.55mm thick with two unequal flange of 20 and 30mm and web of 27mm fixed to surroundings walls with GI wire 4.0mm dia complete with suspenders complete all specified and directed.

S&F 4mm thick designer non asbestos fiber cement building boards designer pre-painted fixed to GI snap grid in ceiling flat complete all as specified and as directed.

S&F 6mm thick plywood grade BWR type BB fixed with screws to timber frame work complete all as specified and directed.

S&F second class hardwood boarding planed one side with butt jointed fixed with nails complete all as specified and directed.

M & L for non-skid mat finish ceramic colour tiles 300x300, 7 to 8mm thick in floors etc. set and jointed in neat cement slurry and pointed with white or coloured to match with tile laid over and including screed bed or bedding layer 15 mm thick in CM (1:6) complete all as specified and as directed. .

M & L for non-skid mat finish ceramic colour tiles area of each tile exc 0.18 sqm but not exc 0.38 sqm, 7-8mm thick, in floor etc in floors etc. set and jointed in neat cement slurry and pointed with white or coloured to match with tile laid over and including screed bed or bedding layer 15 mm thick in CM (1:6) complete all specified and as directed.

M & L for non skid mat finish ceramic colour tiles 600x150, 7-8mm thick on vertical surfaces of wall such as skirtings etc set and jointed in neat cement slurry and pointed in white cement to match with tiles over and incld.10mm thick screed plaster in CM 1:4, complete all as specified and as directed. .

M&L for Vitrified tiles 8-10mm thick of size 600x600mm in floor etc set and jointed in neat cement slurrty and poined in white cement to macth with tiles complete all as specified and as directed.

M & L for glazed ceramic colour tiles 600x300, 7 to 8mm thick on vertical surfaces of wall such as dados, skirtings etc set and jointed in neat cement slurry and pointed in white cement to match with tiles over and incld.10mm thick screed plaster in CM 1:4, complete all as specified and as directed. .

M&L for Screed bed/bedding layer of 15mm thick in cement mortar 1:6 for laying of floor tiles/finishes complete all as specified and as directed.

M&L for Rendering 15mm thick in cement mortar 1:6 on fair faces of Brick walls or on concrete surfaces, finished fair and even, complete all as specified and as directed.

M&L for 15mm thick rendering in Cement Mortar 1:4 on Fair Faces of Brick Walls or on Concrete Surfaces plastered Surfaces Finished fair and even, complete all as specified and as directed.

M&L for 10mm thick rendering in CM 1:4 on Fair Faces of Brick Walls on plastered Surfaces Finished fair and even on one side of lathing, complete all as specified and as directed.

M&L for 10mm thick rendering in CM 1:6 on Fair Faces of Brick Walls on plastered Surfaces Finished fair and even on other side of lathing, complete all as specified and as directed.

M&L for Rendering 5mm thick in Cement Mortar 1:3 on Concrete Surfaces of Ceiling, etc., plastered surfaces finished Even and Smooth, without using Extra Cement, complete all as specified and as directed. .

Supply only Integral Water proofing compound confirming to IS complete all as specified and directed.

S&F flush shutters (single/double Leaf), 30mm thick, solid core construction with block board core & ply wood face panels, commercial type on both side and fitted to wooden chowkats, complete all as specified and as directed.

S & F factory made IInd Class HW 35mm thick glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.20 (a) supplied and fitted to chowkats, complete all as specified and as directed. .

Supply and fix 30 mm thick 2nd class hard wood glazed and skeleton shutters open rebated and prepared to receive glass, gauze etc but divided into squares, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads etc for secuering glass excecter size of members of shutter as specified in SSR part-I, Sec -8 clause 8.24 (b) complete all as specified and directed.

S & F factory made solid PVC moulded door shutter with wood free EPS, 28 to 30mm thick (stiles), design with 2mm thick 3D wood grain moulded PVC sheet painted on the front face & 2mm thick plain colour PVC sheet on back face complete all as specified and as directed.

S & F solid PVC door frame of size 100mm x 45mm made out of 5mm wood grain printed PVC sheet & edges will be painted to match with printed sheet as reinforced with M.S. square tube and fixing in opening as per specification & drawing complete all as specified and as directed.

M&L for 2nd class hardwood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed, complete all as specified and as directed.

S&F Pressed steel frames for doors with one rebate including necessary fixing lugs, hinges, lock strike plate etc complete as specified of size 105x60mm complete all as specified and as directed.

S&F Pressed steel frames for doors with double rebates including necessary fixing lugs, hinges, lock strike plate etc complete as specified of size 125x60mm complete all as specified and as directed.

M&L for Powder Coated (minimum thickness of powder coating 50 micron) anodised aluminium Frame for Doors, windows, ventilators with one or more rebates, aluminium grill and U clips, including jointing cleat for fixing etc, complete all as specified and directed.

M&L for Powder Coated (minimum thickness of powder coating 50 micron) anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified and directed.

S & F in repair 20mm dia, Harrison rails, anodised aluminium alloy with fixing brackets, stops, rollers etc. Powder coated , tubular curtain rail fancy type complete all as specified and as directed. .

M&L for Brick work with sub class B brick straight or curved on plan exc 6.00 m mean radious built in CM 1:6 complete all as specified and as directed.

M&L for brick work with sub-class 'B' bricks straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and as directed.

Material and labour for second class hard wood in scantling clean sawn framed work fixed with nails complete all as specified and directed.

Material and labour for 2nd class hard wood plain fillets, square, rectangular or triangular in section exc. 13 sqcm but n.exc 25 sqcm, wrought secured with nails or brads complete all as specified and directed

Fixing only second class hard wood scantling wrought framed and fixed complete all as specified and directed.

Supply and fix 2nd class hard wood Small fittings such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including all necessary labours; articles n exc 200 cu. cm each complete all as specified and as directed.

Hacking out old broken glass (any thickness, size quality or description) from metal/wood frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones complete all as specified and directed.

Supply and fix 3 mm thick Sheet glass, ordinary quality and glazing with oil putty in squares n exc 0.5 Sq.m in each pane including oil putty and bedding complete fitting complete all as specified and directed.

S & F figured glass pin headed type, 3 mm thick and fixed with oil putty, size of glass n. exc 0.50 sqm in each pane complete all as specified and as directed. .

Supply and fix 100mm size stainless steel butt hinges medium weight cold rolled and fixed complete all as specified and directed.

Supply and fix 75 mm size stainless steel butt hinges medium weight cold rolled and fixed complete all as specified and directed.

Supply and fix 50 mm size stainless steel butt hinges medium weight cold rolled and fixed complete all as specified and directed.

Supply and fix Mild steel barrel tower blots 100 mm long , stove enamelled black, with bright bolt and fixed complete all as specified and directed.

Supply and fix Mild steel barrel tower blots 150 mm long , stove enamelled black, with bright bolt and fixed complete all as specified and directed.

S&F for 150mm long aluminium, anodized, barrel tower bolts of extruded section complete all as specified and as directed. .

Supply and fixing for 300 mm mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12 mm dia fitted with gate using welding complete all as specified and directed.

Supply and fixing 100mm size Mild steel pressed handles ,oval type,stove enamelled black complete all as specified and directed.

Supply and fixing 150mm size Mild steel pressed handles ,oval type,stove enamelled black complete all as specified and directed.

S & F 150mm aluminium handles, cast type, anodised complete all as specified and as directed.

S&F 300mm Mild steel, ordinary rat tail rod pattern springs including roller and roller plate complete complete all as specified and directed.

Supply and fix Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm etc complete all as specified and directed.

Supply and fix in repair Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm etc complete all as specified and directed.

S&F in repair 12mm mess wire netting of galvanised steel wire 0.91mm dia fixed with tinned tacks of wire staples including all laps complete all as specified and directed.

S& F GI wire netting 0.90mm dia and 12mm mesh lathing to wood or metal studding, joists, etc. in walls, ceilings, stanchions, beams, etc. including all laps, cutting and waste, complete all as specified and as directed.

S&F Plain mild steel wire, galvanised class 3, in fencing including straining and fixing to wood, concrete or steel posts and/or to straining boltsin detached work such as for mosquito nets and fixing to straining bolts, hooks, eyes, etc complete all as specified and as directed.

M&L for 15mm dia bore steel tubing medium grade galvanised with all fittings and fixed complete to walls and ceiling or laid in floors incl taking up or down steel tubing 15mm bore complete all as specified & directed

M&L for 20mm dia bore steel tubing medium grade galvanised with all fittings and fixed complete to walls and ceiling or laid in floors incl taking up or down steel tubing 20mm bore complete all as directed.

S&F in repair 15mm bore fancy type CP brass one way or two way Bib Cock (Foam Flow) with Flange (as approved) complete all as specifed and directed.

S&F in repair CP brass 15mm bore Single Lever Basin Mixer without popup waste swan neck Braided Hoses (as approved) complete all as specifed and directed.

S&F in repair CP 15mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed (as approved) complete all as specified and as directed.

S&F in repair Stop/ angle valves 15mm dia bore of pipe, chromium plated, fancy type, with long shank and cap (cocealed type) complete all as specified and as directed.

S&F in repair CP brass 15mm bore Wall Mixer 3-in-1 with provision for both Over Head Shower with Hand Shower with 115mm long bend Pipe (as approved) complete all as specifed and directed.

S&F in repair Chromium plated shower roses with swivel joints, 150x150mm with CP arms 300mm long, including fixing to steel pipe or union complete all as specified and as directed.

S & F in repair tubular towel rail , chromium plated brass 20mm dia ‘D’ type 60 cm long between flanges complete all as specified and as directed. .

S & F in repair PVC connection, heavy duty 15 mm bore, 45 cm long with 2 Nos PTMT nuts of approved quality complete all as specified and as directed. .

S & F in repair PVC waste pipe of 32 mm bore of adequate length complete all as specified and as directed.

S&F in repair, Sheet Glass shelf (corner) Assembly, consisting of 5.5mm thick Glass Shelf 3 tier with Guard and Railing complete all as specified and as directed.

S&F in repair, Sheet Glass Shelf Assembly, consisting of 5.5mm thick Sheet Glass Shelf 12 Cm Wide with Chromium plated Bracket Guard and Railing 60 Cm long, complete all as specified and as directed. .

S&F in repairs vitreous china squatting pattern Orissa pattern Water closet, size 580 x 440 mm white, with integral foot rests including connection to trap, and to flushing pipe, anti-syphonage pipe, etc. complete including making good to floor complete all as specified and as directed.

S&F in repairs PVC Flushing Cistern 10 LITRE capacity White, Low Level, Valve less, syphonic action type with Inlet, Ball Valve, Float and handle, complete all as specified and as directed.

S&F in repairs Vitreous China Wash Hand Basin of size 550x400mm (Flat Back or Angle Back type) with pedestal including 32mm bore (dia) Brass CP Waste Fitting and fixing brackets, complete all as specified and as directed.

S&F in repair for Rotational moulded polyethylene water storage tanks 1000 ltrs capacity (cylindrical vertical with closed top) including wash out GI pipe 32mm of 450mm length with stopper complete all as specified and as directed.

S&F in repair 20mm dia ball brass valves high pressure with polythene float valve & fly nut screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F CP brass Grating Doom 100mm dia (minimum weight 40 Grams) and fixed-in-repairs, complete all as specified and as directed. .

S&F in repair PVC (SWR) 75mm bore (dia) Soil, Waste and Ventilating Pipe, Singe Socketed, in any length with Rubber Ring Joints with and including all fittings like bend, tee, floor/gully trap. or junction etc fixed to Walls or laid in floors complete all as specified and as directed.

S&F in repairs PVC (SWR) 110mm bore (dia) Soil, Waste and Ventilating Pipe, Singe Socketed, in any length with Rubber Ring Joints with and including all fittings like bend, tee, floor/gully trap. or junction etc fixed to Walls or laid in floors, complete all as specified and as directed.

S&F PVC (SWR) multi floor trap with grating including jointing with solvent cement, complete all as specified and as directed.

S & F PVC (SWR) bends of any radius 110 mm dia complete all as specified and as directed.

S&F PVC (SWR) vent cowl 110mm dia complete all as specified and as directed.

Material and labour for preparation of new wood and wood based material over 10 cm in width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Material and labour for preparation of new/old painted wooden surfaces of any description over 10 cm width or girth and applying two coat of synthetic enamel paint complete all as specified and as directed.

M&L for prepration of new steel surfaces and applying two coats of synthetic enamel paint over a coat of red oxide complete all as specified and as directed.

M & L for preparation of old plastered Surfaces of ceiling and applying one Coats of White Wash complete all as specified and as directed. .

M&L for preparing newly Plastered Surfaces of Ceiling and applying Three Coats of White Wash, complete all as specified and as directed. .

Material and labour for preparation of newly plastered surfaces of walls and applying two coats of distemper oil emulsion over a coat of 1mm thick average thick wall putty etc complete all as specified and as directed.

M&L for complete removal of old distempered surface of wall and appliying two coat of distemper oil emulsion over a coat of 1mm average thick wall putty with cement base and making smooth finish, complete all as specified and directed

M & L for new/complete removal of existing treatment of wall and applying POP putty of 1 mm thickness over plastered surface to prepare the surface even and smooth and applying 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade and as directed with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces,complete all as specified and as directed.

Supplying, laying and testing of 150 mm internal dia of double wall corrugaed (DWC) high density polythylene pipe (HDPE) and stiffness classes 8 (SN-8) with ISI marked (With CML No ) with and including all fittings & jointing materials for sewage line and laid in trenches as specified in IS-16098-2013 part-2 complete all as specified and as directed. Make - Rex Polyextrusion Pvt Ltd/Jain irrigation System Ltd/Alom Poly extrusions Limited. Note :- Bedding of pipe shall not be provide in normal condition and construction methods shall be strictly complied as per clause No A-4 of Annex 'A' of IS 16098 Part II.

Excavating in post holes (or similar holes) each n.exc 0.5 cum getting out in soft/lose soil returning, filling in and ramming earth in layers n.exc 25cm, watering and removing surplus soil to a distance n.exc 50m and making good surfaces complete all as specifed and directed.

Excavating in trenches, n.exc 1.5m wide & n.exc 1.5m in depth; for foundation, etc or for shafts, wells, cesspits, manholes, pier holes, etc. nexc10 sq m on plan & n exc 1.5 m in depth & getting out in soft/loose soil.

Returning, filling in including spreading, leveling watering and well ramming in layers n exc 25 cm thick in soft soil, complete all as specified and as directed.

Removing excavated material n exc 50 m and depositing where directed at a level n. exc 1.5 m above starting point, complete all as specified and as directed.

M&L for water proofing treatment to RCC roof slab, including parapet comprising with the following courses of treatment/specification from bottom to top and taking down existing roof treatment complete:- (i) Screed bed or bedding layer of mortar 15 mm thick in CM 1:4 for laying as in roof slab with mixing of WPC and surface finished fare and smooth without using extra cement. (ii) Cleaning of plastered roof surface and applying one coat of cold bituminous primer @ 0.25ltr /Sqm conforming to IS:3384-1986. (iii) APP based polymeric membrane 3mm thick (minimum), weighing 3.5 Kg/sqm reinforced with polyester non woven fabric (weighing not less than 160 gms/Sqm) shall be less applied over bituminous primer as specified above over a Application of polymeric membrance shall by torch application. The overlaps shall be minimum 100mm on the transverse direction and 75mm on longitudinal direction. (iv) Applying two coat of aluminum paint over the APP modified membrance @ 0.11Kg/sqm.

Taking down carefully existing unserviceable copper/ aluminium point wiring (light,call bell, two way, socket or power point etc) complete with fittings/fixures such as switches sockets, ceiling rose, fan regulators,bracket light fittings and making good to the disturbed surface complete all as specified and as directed.

Taking down the existing unservicable main switch/ cut out/ DBs of any type/ capacity/ description as existing at site including making good the disturbed surfaces to match with the existing finishes complete all as specified and as directed.

Taking down carefully unsv aluminium submain wiring of any type /loc including conduit /casing and earth wire and making good the distributed surface of walls /ceiling matching with existing finishes complete all as specified and as directed.

Taking out unsv UG Cable any cross sectional area and connection of any description of any description laying in trenches or fixing with wall or poles complete all as specified and as directed.

M & L for Point wiring with 1.5 Sq mm copper conductor single core FRLSH PVC insulated unsheathed 1100 Volts multistranded drawn through and including rigid PVC Concealed conduit and its accessories of suitable size, high grade ISI marked in walls /roof and PVC boxes of suitable size including fixing/grouting sunken/ surface as per site requirement for mounting the switches / sockets/ regulators etc including running up of 1.5 Sq mm copper conductor FRLSH PVC insulated cable as earth continuity conductor along with wiring and connecting to the common earth dolly for One light point controlled by one, one way switch 5 Amps, complete all as specified and as directed.

All as per item No. 131 but for one ceiling fan / exhaust fan point controlled by one , one way switch and regulator, complete all as specified and as directed.

All as per item No. 131 but for one 3 point 5 Amps socket outlets point controlled by one switch on the same board, complete all as specified and as directed.

All as per item No. 131 but for one 3 pin 5 Amps switch socket outlet point controlled by one switch on independent board, complete all as specified and as directed.

All as per item No 131 here in before but for one light point controlled by one, two way switch 5 Amps, complete all as specified and as directed.

All as per item No 131 above but with two run of 2.5 sqmm multi stranded Single core copper conductor 1100 volts grade FRLSH PVC insulated sheathed cable with one run of FRLSH PVC 2.5 Sqmm multi standard insulated sheathed copper wire as earth continuity conductor along with wiring and connecting to the common earth dolly on independent board, complete all as specified and as directed.

S & F Switch piano flush type single pole one way 5 Amp, 230 Volts, complete all as specified and as directed.

S & F Modular switch piano single pole flush type, two way, 6 amps, 230 volts.complete all as specified and directed.

S & F Socket outlet 2 in 1, 3 pin, 5 Amps complete all as specified and directed.

S & F Switch socket combination flush type multipurpose 2/3 pin 5 Amps two in one , 230 volts complete all as specified and as directed.

S&F Switch socket combination 2 in 1 3 pin, 15 Amp flush type universal, complete all as specified and as directed.

S&F ceilling rose three terminal surface bakelite type AC 50 Hz 230 Volt of size 65x50mm complete all as specified and as directed.

S & F ceiling fan regulator step type, flush type heavy duty suitable to work on 230 Volt AC supply complete all as specified and as directed.

S & F Lamp holder with insulated body, with back plate suitable for batten fittings, complete all as specified and as directed.

S & F LED ADORE 10 W B22 CDL 5 STAR LAMP with B 22 base capacity 1200 lumen complete all as specified and as directed. Make- Havells, Cat No: LHLDEUEBML8Z010 or equivalent in CG / Surya.

S & F sheet metal enclosure MCB DB TPN 4 way with 200 amps rated bus bar 415 volts double door with magnetic locking system complete including removal of old unsv sheet metal enclosure complete all as specified and as directed. .Model- DBTPE004SD, Make-L&T or equivalent in Schinder/ Legrand.

S & F MCB TPN 415 volts suitable for fixing in MCB DB of capacity 63 amps complete all as specified and directed.Model-BB40630C, Make-L&Tor equivalent in Schinder/ Legrand.

S & F sheet metal enclosure MCB DB SPN 4 way with 200 Amps rated bus bar 240 volts double door with magnitic locking system complete all as specified and as directed.. Make:- L&T, Model -DBSPN006D or equivalent in Legrand/ Indo Asian.

S & F sheet metal enclosure MCB DB SPN 8 way with 200 Amps rated bus bar 240 volts double door with magnitic locking system complete all as specified and as directed.. Make:- L&T, Model -DBSPN006D or equivalent in Legrand / Indo Asian.

S & F MCB Double Pole 32 Amps 240/415 Volt, confirms to IS/IEC 60898 Breaking Capacity of 10 kA, C-curve, complete all as specified and directed.Make- L&T, Cat No: BB20320C or equivalent in Schinder/ Legrand.

S & F MCB SP, 240 volts, 6-32A Amps 50 Hz ,confirms to IS/IEC 60898 Breaking Capacity of 10 kA, C-curve, complete all as specified and directed. Make -L&T,Model No-BB10060C,BB10100C,BB10160C or equivalent in Schinder/ Legrand.

S & F wall mounted LED 18 watts ,Batten type T 8 light fitting, 230 volts with extruded aluminium heat sink provided for efficient heat dissipation and intregrated electronic driver connector block etc complete with all accessories internally pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting including Ultra bright LED polycarbonate (T8) tube (Single side connection) 4' x 18 watts with G13 lamp holder complete all as specified and as directed..Model -REGALBATTENT8UPTO1X18WDSBSWH For Batten Fitting and Model-PHOTONULTRAE2.01213T8SSTL18WLED865SPC For T8 Tubelight.

S & F wall mounted LED 10 watts ,Batten type T 5 Mirror light fitting, 230 volts with extruded aluminium heat sink provided for efficient heat dissipation and intregrated electronic driver connector block etc complete with all accessories internally pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting, complete all as specified and as directed.

S & F Energy saving new generation environmental friendly long life versatile presure die cast aluminium IP 66 security light fitting luminaire with high power LEDs as light source and PC Cover having TOP opening seperate driver compartment with IP 66 Protection and impact resistance of IK07 with electronic driver of capacity 15 watts with pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting and GI pipe bracket made out of GI pipe medium grade 32 mm dia 1.5 mtr long bend to required shape complete all as specified and as directed. Make- Havells,Model No - ENDURAPEARLSL15WLED757SASYTOPCMP Or Equivalent in CG / Surya.

M & L for sand cushioning in trenches for cable protection with coarse sand laid dry in trenches with uniform thickness including consolidation complete all as specified and as directed.

Supply & Laying well burnt brick , locally available best quality (sub class "B" bricks ) laid in trences perpendicular to UG Cable protection complete all as specified and as directed.

Supply & Laying LT heavy duty UG Cable of size 25 Sqmm 3.5 Core laid in trences /floor/on wall/service connection PVC Insulated, sheathing and armd 1100 Volts grade with aluminium conductor including connection to the main switch/cut out MCB/MCCB with necessary lugs after cutting to required length complete all as specified and directed.

Supply & Laying LT heavy duty UG Cable of size 10 Sqmm 2 Core laid in trences /floor/on wall/service connection PVC Insulated, sheathing and armd 1100 Volts grade with aluminium conductor including connection to the main switch/cut out MCB/MCCB with necessary lugs after cutting to required length complete all as specified and directed.

S & F GI Tubing light grade of size 50mm dia in protection of cable at road crossing /hard standing/pole protection fixed with clam as per site requirement etc complete all as specified and as directed.

Taking down ceiling fan/ Exhaust Fan of any sweep, keeping with safe custody and refixing the same with replacement of unsv core PVC insulated PVC sheathed 3 core multistranded copper conductor cable of size 23/0.193 from ceiling rose to fan terminal over hauling the fan complete all as specified and as directed.

M&L for replacement Sub main wiring 2 x 6 Sqmm multi-strand FRLSH PVC insulated copper conductor unsheathed cable including concealed conduit and continuous earth wire of FRLSH PVC insulated multi-strand copper conductor of size 6.0 sqmm complete all as specified and directed. Connections of cables with MCBs or bus bars shall be done through appropriate size brass/copper thimbles, complete all as specified and as directed.

Boring holes horizontally under Road without damaging the surface of Road of any type (minimum 1.0 METRE below the Road Surface with the help of GI Tubing not exc. 40mm bore (dia) for passing of UG Cable, complete all as specified and as directed. NOTE: GI Pipe laid will be measured and paid separately under appropriate Item.

Earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick burried directly in ground to a depth not less than 2.25 mtrs below ground level with top edge of earth plate not less than 1.5 mtrs below normal ground level connected to GI earth wire 4 mm dia drawn through and including GI protection pipe of light grade 15 mm bore by means of bolts, nuts, check nuts and washers including excavation earth work provisioning of PCC chamber made of PCC 1:3:6 RCC cover funnel with wiremesh 20mm dia watering pipe Medium grade, GI protection pipe 20mm dia bore all as specified in Electrical Plate No.3 of SSR Part I, complete all as specified and as directed.

Supply and laying in trenches/on piller GI Pipe 40 mm bore dia medium grade ISI marked including all fitting laid in trenches/pillar/on wall complete as per site requirement complete all as specified and as directed.

S&F 3 layered (Outer Green Coloured UV Stabalized, Middle Black Coloured UV Stabalized and Inner Most Layer White Coloured with Antimicrobial Property) PP-R (Polypropyelene Random Copolymer) Pipe 32mm Outer dia, ISI marked, SDR 7.4 and SDR 11 UV Stabalised and Antimicrobial Fusion Welded having Thermal Stabality for Hot and Cold Water Supply all PP-R Plain and Brass Threaded Polypropyelene Random Fittings and laid in Trenches, complete all as specified and as directed.

S & F Gunmetal globe (Class 2) or gate valves (brass insert),with iron wheel head screwed both ends for iron pipe size 40 mm dia complete all as specified and as directed.

S & F Gunmetal globe (Class 2) or gate valves (brass insert),with iron wheel head screwed both ends for iron pipe size 25 mm dia complete all as specified and as directed.

Cutting of existing GI pipe laid 50 mm dia for inserting Tees for new connection of 50 mm x 40 mm dia complete all as specified and as directed.

M&L for connection pieces for inserting 25 mm GI pipe into 50 mm distribution mains complete all as specified and as directed.

M&L for fixing GI plug into 40 mm distribution mains complete all as specified and as directed.

M/S Mahabir Traders

Saraswati Auto Works

R D ENTERPRISE

M/S Singha Enterprise

RC Madan

M/S RANA ENGINEERING ENTERPRISE