SPECIAL REPAIRS TO MT POOL COMPLEX (BLDG NO P-160) AT INS KARNA AND PERIODICALS WORK TO KV SCHOOL AT INS KALINGA UNDER GE (P) NAVY KALINGA VISAKHAPATNAM

Amount

Taking down old tar felt treatment from roof surfaces including plaster etc complete.

M & L for 10mm thick screed bed in CM 1:3 with water proofing compound as per manufacturer instructions applied on the surface to have a smooth surface for laying of water proofing membrane (without using extra lime or cement) (Note : WPC will be measured & paid separately under relevant item as supply only)

M&L for normal water proofing treatment on roof slab portion consisting with following operation :- (i) Cleaning surface by wire brushes, brooming, removing dust and applying hot blown bitumen grade 85/25 @ 1.20 Kg/Sqm (ii) Applying of Polymeric water proofing membrane wt. not less than 3 Kg per Sqm over entire area with overlapping and sealed all as specified and directed (iii) Again applying hot blown bitumen 85/25 @ 1.2 Kg per Sqm over water proofing membrane (iv) Finally Applying a bituminous aluminium primer/paint @ 0.10 kg per Sqm complete all as specified and directed.

Dismantling of wall and ceiling boards any thickness including cover fillets, including removing of dismantled material from work site all as directed.

S&F GI frame work for seamless ceiling comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/intermediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45 mm suspended from soffit at approx. 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (n.exc 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre size of grid of GI frame 600 x 600mm to receive E-board ceiling complete all as specified and as directed.

S&F 4 mm thick E-board ceiling of size 600 mm x 600 mm fixed to timber/ GI/ aluminium frame work with screws in ceiling flat or sloping complete all as specified and as directed.

Demolition floor, hearth or wall tiling including cement mortar bedding (but not backing), and removing rubbish off the premises

M&L for 1st or premium or standard quality non skid ceramic coloured joint free tiles of size 600 x 600 x 6 to 7 mm thick in floor, shelves etc set and jointed in neat cement slurry and pointed in coloured cement to match the surface over and including 15mm thick screed bed in CM 1:6 finished even and rough.

M&L for 1st or premium or standard quality non skid ceramic coloured joint free tiles of size 600 x 600 x 6 to 7 mm thick in skirting etc set and jointed in neat cement slurry and pointed in coloured cement to match the surface over and including 10 mm thick screed bed in CM 1:4 finished even and rough.

M & L for non skid, ceramic “coloured” joint free tiles of size 300 x 300 x 6-7mm thick, in floor, shelves etc, set and jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles over 15mm thick screed bed of CM 1:6 complete of item all as directed.

M&L glazed ceramic coloured tiles 300 x 450x 6-7 mm thick as in vertical surface set & jointed in neat cement slurry & pointed with coloured cement to match over 10 mm thick rendering with CM 1:3 all as specified &directed.

M & L for 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over a screed bed of 20mm thick in cement mortar 1:4

M&L for acid resistant tiles 15 mm thick vitreous ceramic, unglazed, set, jointed and pointed in chemical resistant mortar, resin type, in floors over screed bed of 15 mm thick in CM 1:6 for laying floor finishes

M & L for Treatment of soil under existing floors using emulsion @ one litre per hole , 300 MM apart including drilling and plugging 12 MM dia holes with cement mortar 1:2 to match the existing floors.

M & L ATT at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6 mm dia holes at a downward angle of 45 degree at 150 mm centre to centre and sealing the same .

M& L for ATT along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc in apron complete.

Taking down Chowkhats or frames not exc. 1.5 sq. m each with shutters (without taking off shutters from the frames)

Taking down Chowkhats or frames exc. 1.5 sq. m but n exc 4.0 Sqm each with shutters (without taking off shutters from the frames)

M&L for 2nd class hardwood Plain, solid, straight chowkhats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and as directed..

S&F angle iron/ Flat iron work as in hold fast ,support of valley gutter and nosing etc. conforming to Fe-290 Gde-165

M&L for PCC (1:3:6) type C-1 using 20 mm graded crushed stone aggregates as in hold fast block complete.

S&F II class Hard wood , factory made, 35 mm thick plain framed, panelled shutters ( Two panels),with lock rail and panel of 9 mm BWP commercial ply or 12mm veneered particles board with commercial veneering on both faces. the size of rail and stile as per IS 2009 (part-I)

S & F for Solid PVC Door Frame of size 50mm x47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, supplying & fixing in opening as per specification & drawing

S&F factory made solid panel PVC door shutter 30mm thick (style)consisting of frame made out of MS tubes for top & bottom rail, MS frame shall be covered with heat moulded plain cover PVC "C" channel having a PVC sheet strip of 20mm width stuck in side with solvent cement for styles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side & as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the styles and rails with suitable PVC sheet beading and jointed together with solvent cement.

S & F 125 mm Butt hinges, Medium weight, cold rolled mild steel, and fixed , Type-B-12

S & F of 200mm Aluminium anodised, barrel tower bolts of extruded section.

S & F Aluminium handles, cast type, anodised of size 150 mm

S & F 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy.

S&F UPVC window, (unplastisized poly-Vinyl Chloride) sliding windows multi-chambered and stiffened framed windows using 88 mm x 52mm size sections all-round as main frames and shutters made with profile sections of size 57mm x 42mm, including the cost and fixing of 5mm thick clear float glass in shutters and stainless steel wire mesh shutters shall have well defined welded corner joints without any gaps, fixed the window unit to the existing masonry with anchor fasteners as required. The shutters shall have necessary handles and other associated fittings to facilitate smooth operation. Both the frames and the shutters shall be reinforced with Gl profiles of thickness 1.25mm the entire window is covered with MS powder coated tube of size 40mm x20mm all-round the frame the frame section, 10mm square bars horizontally placed at 120mm C/C and suitably placed vertically to avoid buckling and providing structural strength, minimum weight shall be 10kg/Sqm and fixed to UPVC frames with suitable fasteners. The gaps between the window tames and masonry walls shall be filled with silicon or with any other suitable filler materials. (Make : Rajshri Plastiwood/ Sintex/ Duroplast extrusion Pvt Ltd.)

Supply only 4mm thick plain sheet glass & fixed in aluminium frame work.

S&F aluminium XPM wire cloth 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified and as directed.

S&F anodised coloured aluminium grill complete all as specified and as directed by the Engineer-in-Charge.

S & F powder coated aluminium frame for doors, windows, ventilators with one or more rebates including jointing cleat for fixing etc, (minimum thickness of powder coating 50 micron) complete all as specified and as directed.

S&F anodised powder coated aluminium door shutters including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws and suitable anodised aluminium handles and rollers complete all as specified (minimum thickness of powder coating 50 micron) complete all as specified and as directed by the Engineer-in-Charge.

Demolition of brickwork or stone/boulder masonry built in cement mortar or cement lime mortar

M&L for half Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:4

M&L Brick work with fly ash bricks straight or curved on plan exc 6.0 mtr mean radius built in cement mortar (1:6) complete all as specified and as directed

Taking down cement plaster on brick walls including racking out joints hacking for key scrubbing down with water etc complete.

M&L Repair to Beam/chajja/drop/facia,( Broken / damaged) making good with PCC 1:2:4 type B1 or cement mortar 1:3, Rendering 15 mm thick with using water proofing compound , sides and soffits in cement mortar 1:4 including necessary form work wherever damaged, including re-inforcement duly welded if required, including demolition of broken/ loose PCC or taking down old plaster height up to 12 M.

M&L for rendering cement plaster 15 mm thick on other than fair faces wall in CM 1:6 finished even and smooth without using extra cement.

M&L for 15 mm thick rendering on fair faces of brick work or concrete surfaces in cement mortar 1:4 in double layer, using integral waterproofing compound in the outer 5mm thick layer finished fair and even. (Note : WPC will be measured & paid separately under relevant item as supply only)

M&L for rendering cement plaster 5 mm thick on fair faces of ceiling in CM 1: 4 finished fair and even without using extra cement.

Supply only Integral Water Proofing Compound (ISI marked) of approved make.

M & L for preparation of new plastered surface (internal walls) and applying two coats of Oil bound distemper over one coat of primer over wall care putty of 1 mm thick all as specified and directed

M & L for complete removal of existing treatment on internal walls and applying two coats of Oil bound distemper over one coat of primer over wall care putty of 1 mm thick all as specified and directed

M & L for preparation of new surface of walls and applying two coats of Exterior emulsion weather coat paint over a coat of primer over wall care putty of 1 mm thick for external surface on walls complete all as specified and as directed by the Engineer-in-Charge.

M & L for complete removal of existing treatment on walls and applying two coats of Exterior emulsion weather coat paint over a coat of primer over wall care putty of 1 mm thick for external surface on walls complete all as specified and as directed by the Engineer-in-Charge.

M & L for preparation of new surfaces and applying three coats of white wash on wall

M & L for preparation of old surfaces and applying three coats of white wash on wall

M & L for preparation of old surfaces and applying three coats of white wash on Ceiling

M & L for preparation of new surfaces and applying three coats of white wash on Ceiling

S & F in repairs PVC (SWR) pipes 110 mm dia single socketed in any length with rubber ring joints fixed to walls

S & F in repairs PVC (SWR) pipes 75 mm dia single socketed in any length with rubber ring joints fixed to walls

S & F PVC (SWR) vent cowl 110mm

S & F PVC (SWR) vent cowl 75mm

PVC (SWR) bends any radius 75mm

PVC (SWR) bends any radius 110 mm

S & F in repairs Bib taps 15mm dia Fancy type Chromium Plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed

S & F in repairs two way bib cock, CP, Fancy type - 15mm dia

S & F in repairs brass CP angular stop cock including connection complete all as specified and as directed.

S & F in repair Health Faucet for 15mm dia with 1.5m long easy flex tube in Chrome finish and wall look

S & F in repairs Tubular towel rod brass chromium plated, 20mm dia, 60cm long between flanges

S&F, in repair VC semi counter mounted Wash Hand Basin, white, size 25.5 x 20 x 6.45 inch including coupling and all fixing arrangements complete all as specified and as directed.

S & F repairs 3 hole basin mixer with pop up waste assembly, fancy type and connection with quarter turn fitting complete all as specified and as directed.

S & F in repair Vitreous China wash down water closet pan (pedestal pattern), white (including fixing bolts and Seat Cover)

S&F in repair PVC Flushing cistern 10 ltr capacity with inlet ball valve float and handle and 32mm bore flush pipe including bracket complete all as specified and directed.

S & F in repair Vitreous China urinal, half stall type, white including urinal spreader of PTMT any colour for fixing with 15 mm dia pipe complete all as specified and directed.

S & F in repair Soap dish chromium plated, fixed to plugs with chromium plated brass screws

S & F in repair PVC flexible connections 15mm size with PTMT nuts of length 600mm

S & F in repair 125mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement

S&F in repair Rotational moulded polyethylene water storage tanks 1000 litres capacity cylindrical vertical with closed top hoisted and fixed in position over roof top including foundation for water tank, complete all as specified and directed by the Engineer- in- charge

S&F ball valve high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for 20mm dia iron pipe and fixed.(Minimum weight 210gm) complete all as specified and as directed

S&F Gun metal gate valve with iron wheel head ,screwed both ends for iron pipe and fixed 25 mm bore complete all as specified.

Taking up or down 15mm bore, steel tubing and connection including cleaning for refixing or removal from site.

Taking up or down 20mm bore, steel tubing and connection including cleaning for refixing or removal from site.

S & F 25 mm outer dia, 3-layer PP-R (Polypropylene random copolymer) for concealed pipes SDR 7.4 (PN - 16) UV stabilised and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc.

S & F 20 mm outer dia, 3-layer PP-R (Polypropylene random copolymer) for concealed pipes SDR 7.4 (PN - 16) UV stabilised and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc.

Demolition of reinforced cement concrete in roof, floor (other than ground floor) beams, staircase, chajja and similar suspended works (reinforcement cut as required to facilitate demolition) complete all as specified and as directed.

Demolition of Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level)

M&L for 75mm thick PCC 1:3:6 type C1 using 20 mm graded stone aggregate as in plinth protection , pavement surface finished even and smooth without using extra cement complete all as specified and directed.

M&L for precast cement concrete shelves chajja etc Type B-0 1:2:4 (12.5 mm gde agg) and setting complete.

M&L for Reinforced Cement Concrete, 1:1.5:3, type A1 (Using 20mm graded granite stone aggregate) as in slabs supported on walls, beams, and columns in floors, roofs, landings, balconies, canopies, deck slab and shelves and the like etc.

M&L for TMT bars of 8mm dia and cut to length bent to shape required including cranking ,bending and binding with and including mild steel wire annealed not less than 0.9mm dia complete

M & L for Plain Cement concrete 25mm thick type B-0, 1:2:4 (12.5mm graded aggregate) in sub base

M & L for Plain Cement concrete 40mm thick type B-1, 1:2:4 (20mm graded aggregate) in sub base

M & L for Plain Cement concrete 75mm thick type B-1, 1:2:4 (20mm graded aggregate) in sub base

M & L for Plain Cement concrete 100mm thick type C-2, 1:2:4 (40mm graded aggregate) in sub base

M & L for designer rubber moulded chequered cement concrete tiles 30 cm x 30cm x 25 cm thick conforming to IS-13801-1993 with grey cement and pigments, set, jointed and pointed in neat cement slurry in floors including 20mm thick screed bed in cement mortar (1:4) complete all as specified and as directed

S & F in repair steel rolling shutter 1.25 mm thick of lath steel with ball bearing and safety lever lock mild steel, with 4 levers for rolling shutter as specified including top cover anchoring rod, hasp and staple and one coat of primer erected in position as indicated complete all as specified and as directed.

M&L for two coats of synthetic enamel paint on new steel surfaces, over a coat of red oxide primer, over 10 cm in width or girth not other wise described complete.

S&F safety lever locks mild steel with 4 levers for rolling shutters complete all as specified and as directed.

M & L for complete removal of existing treatment on walls and applying two coats of plastic emulsion paint over a coat of primer complete all as specified and as directed by the Engineer-in-Charge.

M & L for complete removal of existing treatment on walls and applying two coats of Exterior emulsion weather coat paint over a coat of primer for external surface on walls complete all as specified and as directed by the Engineer-in-Charge.

M&L applying one coat of synthetic enamel paint including preparation of old steel surfaces over 10 cm width or girth, complete all as specified and as directed.

M&L preparation of old wooden surface of any description not otherwise described and exc 10cm width or girth applying one coat of synthetic enamel paint first grade quality over a coat of pink primer, complete all as specified and as directed.

M&L for preparation of old plastered surfaces of ceiling and applying two coats of white wash, complete all as specified and as directed by the Engineer-in-Charge.

Taking down carefully existing aluminium conductor point wiring (light / fan / socket or power point) complete, with all fittings such as switches, socket, regulator, ceiling rose, utility light fittings and lamp holders etc. and removing materials from site and making good the disturbed surfaces of walls roof and floor etc as per existing specification complete all as specified and as directed.

Taking down carefully by unscrewing from boards / outlet boxes, fittings and fixtures such as switches, sockets, ceiling roses, lamp holders, brackets, ceiling fittings, bulk head fittings, tube light fittings and fan regulators etc. for reuse at site complete all as specified and as directed. (Note : To be measured only when found serviceable in all respects complete for reuse)

Material and labour for point wiring for one light controlled by 1 one way switch with 1.5 Sqmm PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable 1100 Volts grade drawn carefully through existing/New concealed conduit along with 1.5 sqmm continuous PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable for earth continuity wire, connected to earth dolly and to be terminated in and including new pressed steel sunken boxes , readily available (Having wall thickness not less than 1.22 mm for boxes upto a size of 200 mmX300 mm and beyond that the wall thickness shall be not less than 1.63 mm) concealed type with 3mm thick Bakelite sheet cover for mounting switches, sockets, fan regulators etc including testing on completion complete including making good disturbed surface all as specified and as directed.

All as per Item no 100 here-in-before but for one fan E/Fan point controlled by 1 one way switch and regulator all as specified and as directed.

All as per Item no 100 above but for one 3 pin switch socket outlet, 5 Amp on independent board all as specified and as directed.

All as per Item no 100 here-in-before but for one switch socket outlet, 5 Amp on same board with other switches all as specified and as directed

All as per Item no 100 here-in-before but for one 16 Amp 3 & 5 pin switch socket outlet, independent with 4.0 Sqmm single core multi-stranded copper conductor cable (FRLS) along with 4.0 sqmm continuous PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable for earth continuity wire all as specified and as directed.

Material and labour for sub main wiring with two single core PVC insulated un-sheathed cable with multi-stranded copper conductor of 1.5 sq mm size and drawing into and including concealed PVC conduit with earthing cable of PVC insulated un-sheathed stranded copper conductor of size 1.5 sqmm, single core, as earth continuity wire all as specified and as directed. (Note : 3 runs of 1.5 Sqmm cable and one run of PVC conduit shall be measured as one unit)

Material and labour for sub main wiring with two single core PVC insulated un-sheathed cable with multi-stranded copper conductor of 6.0 sq mm size and drawing into and including concealed PVC conduit with earthing cable of PVC insulated un-sheathed stranded copper conductor of size 6.0 sqmm, single core, as earth continuity wire all as specified and as directed. (Note : 3 runs of 6.0 Sqmm cable and one run of PVC conduit shall be measured as one unit)

S & F modular plate switch flush type single pole one way 6 Amp, 250 volt , complete all as specified and as directed.

Fixing only switch flush button single pole one way 5 amp all as specified and as directed. (Note : Material obtained from item No 99 here in before shall be reused)

S & F modular plate switch flush type single pole one way 16 Amp, 250 volt , complete all as specified and as directed.

M&L modular socket 6 Amps 5 pin complete all as specified and as directed.

Fixing only switch socket outlet 5 amp flush type all as specified and as directed. (Note : Material obtained from item No 99 here in before shall be reused)

M&L modular socket 6-16 Amps 2/ 3 pin combined shutter complete all as specified and as directed.

S&F modular step type fan regulator 120 watt two module five steps and back plate complete all as specified and as directed.

S&F modular plate white colour suitable for flush metal boxes for mounting modular switches or sockets etc for 8 modules complete all as specified and as directed.

All as per Srl Item No. 114 here-in-above but for 6 modules

All as per Srl Item No. 114 here-in-above but for 3 modules

All as per Srl Item No. 114 here-in-above but for 2 modules

S&F flush metal box 1/2 module complete all as specified and as directed.

All as per Srl Item No. 118 here-in-above but for 6 modules

All as per Srl Item No. 118 here-in-above but for 3 modules

All as per Srl Item No. 118 here-in-above but for 8 modules

Supply and fixing ceiling rose surface bakelite three terminals all as specified and as directed.

Fixing only ceiling rose surface bakelite three terminals all as specified and as directed. (Note : Material obtained from item No 99 here in before shall be reused)

Supply and fixing sheet metal enclosure for MCB, DBs, phosphatised, Powder coated , Triple Pole and Neutral (TPN), suitable for 4 way, Double door 415 Volts all as specified and as directed .

Supply and fixing sheet metal enclosure for MCB, DBs, phosphatised, Powder coated , single pole and neutral (SPN) 240 Volt , double door, suitable for 8 way with din rail earth and neutral bar all as specified and as directed.

Supply and fixing MCB Four Pole (FP) C curve 10kA breaking capacity of 63 amps, 415 Volts in proper position all as specified and as directed.

Supply and fixing MCB Single Pole (SP) C curve 10kA breaking capacity of 6 to 32 amps, 240 Volts in proper position all as specified and as directed.

S&F in proper position MCB Double Pole of capacity up to 40 amps, 240 Volts c-series with 10kA breaking capacity all as specified and as directed.

Supply and fixing indoor luminaire decorative batten for wall/ceiling mounting box type energy efficient saving LED BATTEN LIGHT 10 W, 230 V, 50 HZ, slim integrated design easy install including twin twisted copper conductor flexible wire from ceiling rose to connector all as specified and as directed.

Supply and fixing indoor luminaire decorative batten for wall/ceiling mounting box type Extruded aluminium housing ,PC Diffuser, energy efficient saving LED BATTEN LIGHT 20W,230 V,50 HZ, slim integrated design easy install incl twin twisted copper conductor flexible wire from ceiling rose to connector all as specified and as directed.

Supply and fixing LED bulk head fittings 10 W,230 V,50 HZ suitable for indoor and outdoor applications complete all as specified and as directed. Make Surya cat no SLE BH 10 W or equivalent as approved by GE.

Supply and fixing on wall security LED light luminaire fitting 1X25 W and including cable for connection from celling rose with 1.5 Sqmm PVC insulated stranded copper conductor (FRLS) cable including 25 mm GI bracket medium grade 1m long bent to shape including bolt, nut,washer,clamp etc. all as specified and as directed by the Engineer-in-charge.

Taking down carefully ceiling fan any sweep and any make after disconnecting the electrical connection, dismantling the blades and removing fan incl blades for safe custody for reuse and re-assembling the fan complete and refixing the fan in same position including all electrical connection all as specified and as directed.

Material and labour for taking out and removing burnt copper winding, cleaning the armature, rewinding the fan armature for 1200mm sweep fan with new super enamelled copper wire of existing gauge including supply and fixing necessary insulating materials etc and varnishing with approved grade of insulation varnish and heating up and testing all as specified and as directed.

Supply only bearing No. 6201/6202 for ceiling /Exhaust fan.

Supply only fan condenser upto 2.5 mfd.

Material and labour for painting of ceiling fans complete of any sweep/make with one coat of first quality synthetic enamel paint of approved tint by spray including preparation of old painted surface and removing all dust, oil mark etc and filling cavities with filler materials, and writing serial / MES number as specified (with paint of black colour with each letters/figures in Block of height n.exc2 cm ) complete all as specified and as directed.

S&F Exhaust fan wall mount type 300 mm sweep metal body , single phase with louver shutter and connecting up including provision of hold fasts for fixing fan and louver shutter with cutting of hole and necessary PCC(1:3:6) all as specified and as directed.

Material and labour for XLPE insulated GI wire/strip armoured electric power cable (Heavy duty) ISI marked with stranded aluminium conductor 1100 volts grade, cross sectional area 70 Sqmm 3.5 core laid in trench /poles/on wall all as specified and as directed .

Excavation in trenches not exc 1.5 mtr wide and not exc 1.5 mtr in depth; for trench of FRLS cable etc and getting out in Soft/loose soil complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in Soft/loose soil complete all as specified and as directed

Removing excavated material to a distance n.exc 50 mtr and depositing where directed at level and exc 1.5 mtr above the starting point all as specified and as directed

Material and labour for sand cushioning for protection of underground FRLS cable consolidated and compacted with clean dry sand all as specified and as directed (Note : Compacted thickness shall only be measured and paid)

Supply and lay bricks common burnt clay building bricks sub-class B of size 230x113x75 complete all as directed by Engr-in-Charge.

Drilling of hole horizontally 80/40 mm dia below the road for providing casing pipe of cable protection by using mechanical /hand drill all as specified and as directed.

Material and labour for galvanized iron tubing 50 mm bore light grade with all fitting for protection of FRLS cable, laid in trenches/wall/floor including necessary clamp, bolt/ nut if any all as specified and as directed. (Note: Excavation ,earth work shall be measured and paid separately)

M&L for Earthing complete with 3 m CI pipe 80 mm dia with flanged ends, centrifugally cast, class A, in any length, joints with suitable stainless steel nuts and bolts and sufficient slate up to 2.5mtrs length buried directly and preferably vertically in ground with top flanged ended 2.5mtrs below ground label welded/connected with GI strip 32×6mm size on the top edge of the flange to bottom edge of the flanged for earthling including filling the pit with charcoal common salt surrounding the earth pipe including drilling 400 mm dia bore in any strata of soil to lower the CI pipe complete including necessary excavation and earth work PCC (1:3:6) type C-1 with 50 mm thick pre cast RCC (1:2:4) type B-1 cover slab and necessary testing on completion complete all as specified and as directed.

VASANTHA NAIDU ASSOCIATES

N V S S K N SIVA PRASAD

SRI RAJA RAJESWARI ENTERPRISES

SRI VENKATA SAI MANIKANTA CONSTRUCTIONS

F AND M TECHNOLOGIES

P SRINIVASA RAO