REPAIR TO FLOORING PLUMBING PLASTER SANITARY JOINERY AND OTHER B AND R WORKS IN ZONE-A AT DEFENCE LAB JODHPUR

Amount

Demolition of floor, hearth or wall tiling including cement mortar bedding or backing coat, removing rubbish off the premises, removal and depositing where directed and leaving the more clean of any plastering complete all as specified and directed by Engineer-in-charge.

Demolition of cement concrete unreinforced in ground floors, kota stone, granite flooring, tiles flooring and pavings not exceeding 15cm thickness (below or above ground level) and removal unserviceable materials, debris and rubbish to a distance not exceeding 100m complete all as specified & directed by Engineer in charge.

M&L non-skid ceramic coloured tiles of 7 to 8mm thick, (square / rectangular) area of each tiles exceeding 0.11 Sqm but not exceeding 0.18 Sqm, as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including screed bed or bedding layer of 15 mm thick in CM (1:6) complete all as specified and directed by Engineer-in-charge.

M&L non-skid ceramic coloured tiles of 7 to 8mm thick, (square / rectangular) area of each tiles exceeding 0.11 Sqm but not exceeding 0.18 Sqm, as in skirting, set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including backing coat of 10mm thick in CM (1:4) complete all as specified and directed by Engineer-in-charge.

M&L glazed ceramic coloured tiles of size 350 x 250mm x 7mm /450mmx350mmx7mm/450mmx300mmx 7mm thick on vertical surface such as skirting, dados, risers to steps etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including 10mm thick backing coat in CM (1:4) complete all as specified and directed by Engineer-in-charge.

M&L non-skid ceramic coloured tiles of 7 to 8mm thick, (square / rectangular) area of each tiles exceeding 0.06 Sqm but not exceeding 0.11 Sqm, as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including screed bed or bedding layer of 15 mm thick in CM (1:6) complete all as specified and directed by Engineer-in-charge.

M&L full body vitrified 300x1200x15 mm thick steps with self embossed treated lines anti-skid surfaces including bull nosed edges set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including screed bed or bedding layer of 15 mm thick in CM (1:6) complete all as specified and directed by Engineer-in-charge.

M&L18 to 20 mm thick granite stone slab machine cut bedded and jointed with grey cement slurry and pointed with white cement or coloured cement to match the colour of granite as in flooring / cooking platform over and including 15mm thick screed bed in cement mortar (1:4) complete all as specified & directed by Engineer-in-charge.

M&L 50 mm thick PCC (1:3:6) type C-1 using 20 mm graded crushed stone aggregate laid in alternative bays as in plinth protection including finishing the surface even & fair & filling the joints with mastic filling i.e one part of bitumen 85/25 and 3 parts of sand by weight complete all as specified & directed by Engineer-in-Charge

Demolition of brickwork or stone/boulder masonry, built in cement mortar including all quoins arches, pillers etc but excluding ashlar facings, dressed stone work and precast concrete articles and removal unserviceable materials, debris and rubbish to a distance not exceeding 100m complete all as specified & directed by Engineer-in-charge.

M&L squared rubble walling, Jodhpur type, brought upto courses, well bonded, bedded and solidly hearted, built in cement mortar (1:6) complete all as specified & directed by Engineer-in-charge.

M&L squared rubble walling, Jodhpur type, brought upto courses, well bonded, bedded and solidly hearted, built in cement mortar (1:6) except stone complete all as specified & directed by Engineer-in-charge.

Extra over stone walling for hammer dressing to face stones with maximum depression on face from a straight edge not exceeding 20mm & dressing face beds and joints as specified to squared rubble walling Jodhpur type brought up to courses or regular course complete all as specified & directed by Engineer-in-charge.

M&L keyed pointing in cement mortar (1:3) to squraded rubble masonary coursed or un coursed complete all as specified & directed by Engineer-in-charge.

Taking down cement or cement lime plaster, any description on brick or stone walls/ceiling etc including racking out joints, hacking for key, scrubbing down with water etc and removal of rubbish off the premises and leaving the work clear of any plastering complete all as specified & directed by Engineer-in-charge.

M&L 15 mm thick, plaster in cement mortar (1:4) on stone masonry wall surfaces or surfaces other than fair faces of brick work or one side of lathing and finishing the surface even and smooth without using extra cement complete all as specified & directed by Engineer-in-charge.

M&L rendering 10 mm thick plaster in cement mortar (1:3) on concrete surfaces of ceiling and finishing the surface even and smooth without using extra cement complete all as specified and directed by Engineer-in-charge.

Taking down chowkhats or frames not exceeding 1.5 Sqm with shutters (without taking off shutters from the frame) complete all as specified and directed by Engineer-in-charge.

Taking down chowkhats or frames exceeding 1.5 Sqm but not exceeding 4 Sqm each with shutter (without taking off shutters) complete all as specified and directed by Engineer-in-charge.

S&F solid PVC door frame of size 50 x 47mm made out of 5mm plain colour PVC sheet re-inforced with M.S. square tube supplying and fixing in opening as per specification and drawing in SSR Part II, complete all as specified and directed by Engineer-in-charge.

S&F factory made solid panel PVC door shutter 30mm thick (Style) consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strips of 20mm width stuck inside with solvent cement for tiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed the stiles and rails with suitable PVC Sheet beading and jointed together with solvent cement supplying and fixing in the frame at site all as per specification and drawing in SSR Part-II , complete all as specified and directed by Engineer-in-charge.

S&F 100mm size,PTMT butt hinges with steel screws complete all as specified and directed by Engineer-in-charge.

S&F 150 mm size PTMT barrel tower bolts with steel screws complete all as specified and directed by Engineer-in-charge.

S&F 150mm size PTMT door handles with steel screws complete all as specified and directed by Engineer-in-charge.

S&F pressed steel frames (size 125 x 60mm) for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc. complete all as specified & directed by Engineer-in-charge.

S&F pressed steel frames (size 165 x 60mm) for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc. complete all as specified & directed by Engineer-in-charge.

S&F IInd class hard wood 35mm thick Factory made plain framed panelled shutter any number of panels of timber flat on both sides, with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces the size of rail and stile as per IS 1003 (Part-I) kiln seasoned and chemically pressed treated complete all as specified and directed by Engineer-in-charge.

S&F 35mm thick factory made 2nd class HW glazed and skelton shutter and open rebated and prepared to receive glass, gauge etc (without sash bars), edges or framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc size of members of shutter as specified in SSR Part-I Section 8 Clause 8.24 (a) complete all as specified and as directed by the Engineer-in-charge.

M&L plain cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate cast in situ in lintels up to 1.5 m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings up to 60 cm in height, copings, kneelers, apex stones, bed plates, water through and the like including weathering, slightly rounded or chamfered angles and throating including use of form work (straigth or curved) complete all as specified & directed by Engineer-in-charge.

S&F factory made steel windows with side hung shutters including projecting type hinges with steel handle and steel peg stay complete with glazing bars, dovetailed or welded complete all as specified & directed by Engineer-in-charge.

S&F factory made steel windows with side hung shutters including projecting type hinges with steel handle and steel peg stay complete without glazing bars, dovetailed or welded complete all as specified & directed by Engineer-in-charge.

S&F steel window or ventilators, fixed type, with glazing bars complete all as specified & directed by Engineer-in-charge.

Hacking out old broken glasses (any thickness, size, quality or description) from steel/wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads etc complete all as specified & directed by Engineer-in-charge.

S&F 3mm thick, sheet glass ordinary quality and glazing with oil putty in squares not exceeding 0.50 Sqm in each panes complete all as specified and directed by Engineer-in-charge.

S&F 3mm thick, figured glass, pin head type and glazing with oil putty in squares not exceeding 0.50 Sqm in each panes complete all as specified and directed by Engineer-in-charge.

S&F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aparture 1.40mm and fixed with stainless steel wire stapples complete all as specified & directed by Engineer-in-charge.

S&F 150 mm long, mild steel, pressed handles, oval type, stove enamelled black complete all as directed by Engineer-in-charge.

S&F 150mm long, mild steel, barrel tower bolts, stove enamelled black with bright bolt complete all as directed by Engineer-in-charge.

S&F 300mm long mild steel sliding door bolts plate type, stove enameled black, with bright bolt not less than 12mm dia and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate complete all as directed by Engineer-in-charge.

S&F 150 mm size mild steel helical door spring including roller and roller plate complete all as specified & directed by Engineer-in-charge.

S&F 140mm long floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified & directed by Engineer-in-charge.

S&F in Repair 20 mm dia curtain rails,decorative mild steel,coloured powder coated approved pattern & design including side cups with fixing brackets,stop,rollers etc complete all as specified and directed by Engineer-in-chage.

Taking up or down 15mm bore steel tubing and connections including cleaning for refixing or removal to store complete all as specified and directed by Engineer-in-charge.

Taking up or down 20mm bore steel tubing and connections including cleaning for refixing or removal to store complete all as specified and directed by Engineer-in-charge.

S&F GI tubing (ISI marked) 15mm bore medium grade with all fittings and fixed complete to walls and ceiling or laid in floors (concealed tubing) complete all as specified and directed by Engineer-in-charge.

S&F GI tubing (ISI marked) 20mm bore medium grade with all fittings and fixed complete to walls and ceiling or laid in floors (concealed tubing) complete all as specified and directed by Engineer-in-charge.

Fixing only GI tubing (ISI marked) 15 mm bore medium grade with all fittings and fixed complete to walls and ceiling or laid in floors (concealed tubing) obtained from taking down complete all as specified and directed by Engineer-in-charge.

Fixing only GI tubing (ISI marked) 20 mm bore medium grade with all fittings and fixed complete to walls and ceiling or laid in floors (concealed tubing) obtained from taking down complete all as specified and directed by Engineer-in-charge.

S&F in repairs vitreous china squatting pan "Orissa" pattern, size 580 x 440mm white, with integral foot rest (Excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe,lime/cement concretebedding and making good to the floor complete all as specified and directed by Engineer-in-charge.

S&F in repair vitreous china wash down water closet pan/ padestal(EWC) including plastic water closet seat,black,closed pattern with flat bottom,and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed by Engineer-in-charge.

S&F in repairs 10 ltrs capacity PVC valve less, syphonic action type, flushing cistern, low level, white with inlet, ball valve, float and handle including brackets, complete all as specified and directed byEngineer-in-charge.

S&F in repair vitreous china wash basin white, flat back of size 550 x 400 mm white including waste fittings, brass chromium plated , coupling,pvc waste pipe32 mm size, brackets including cutting for and pinning in ends of brackets errect stand, fixing waste pipe complete all as specified & directed by Engineer-in-charge.

M&L 75 mm size cast iron floor, trap, with grating including jointing to waste pipe fixed in cement conrete (1:2:4) type B-1 including taking down old un-serviceable floor trap complete all as specified & directed by Engineer-in-charge.

S&F in repairs CP grating for Nahani trap/ floor trap of size 100/75 mm bore complete all as specified & directed by Engineer-in-charge.

S&F in repairs PVC connections 450 mm long, 15mm size with PTMT nuts for WHB, flushing cistern, geysers etc complete all as specified & directed by Engineer-in-charge.

S&F in repairs PVC connections 600 mm long, 15mm size with PTMT nuts for WHB, flushing cistern, geysers etc complete all as specified & directed by Engineer-in-charge.

S&F, in repair, 32 mm dia, 600/750 mm long PVC waste pipe for wash basin, sink etc complete all as specified & directed by Engineer-in-charge.

S&F in repairs, brass chromium plated, fancy type, bib taps, with crutch or butter fly handle, screwed down, screwed for 15 mm bore iron pipe or for brass ferrule complete all as specified & directed by Engineer-in-charge.

S&F in repairs stop cock, fancy type, chromium plated, with long shank and cup (concealed type) cast copper alloy, screwed down, high pressure, with crutch or butter fly handle, screwed both ends for 15 mm bore iron pipe or for union complete all as specified & directed by Engineer-in-charge.

S&F in repairs pillar taps, cast copper alloy, with half turn handle type, chromium plated, screwed down high pressure, with or without lettered 'Hot' & 'Cold' with long screwed shanks and fly nuts, screwed for 15 mm bore iron pipe complete all as specified & directed by Engineer in charge.

Dismantling of old unserviceable PVC water tank of 1000 Ltrs capacity complete all as specified and directed by Engineer-in-charge.

S&F 1000 ltrs capacity rotational moulded polythene water storage tanks white three layered (ISI marked) (Cylinderically vertical with closed top) hoisted and fixed in postion all as specified in SSR Part-I including PTMT ball valve heigh pressure with epoxy coated aluminium rod and high density plastic ball suitable for 20mm bore pipe weight not less than 210gms complete all as specified and directed by Engineer-in-charge.

S&F in repairs, 110mm bore PVC (SWR) single socketed in any length with rubber ring joints & fixed to walls complete all as specified and directed by Engineer-in-charge.

S&F in repairs, 110 mm bore (SWR) PVC bends any radius complete as specified and directed by Engineer-in-Charge.

Dismantling cast iron work of any description and in any position complete all as specified & directed by Engineer-in-charge.

Dismantling of 100mm bore cast iron or reinforced concrete drain pipes, jointed in cement mortar/lead joint and taking out of trenches if required /walls including fittings, complete all as specified & directed by Engineer-in-charge.

S&F in repairs 100 mm bore cast iron P or S trap complete all as specified & directed by Engineer-in-charge.

S&F in repairs100 mm bore CI branch piece, single, (equal or unequal) ordinary or inverted (spigot or socket type) or with paralled branches with ovel access door including jointing in CM (1:1) complete all as specified & directed by Engineer-in-charge.

S&F, in repairs 100mm dia, cast iron nahani trap with grating including jointing to waste pipe fixed in cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate all as specified and directed by Engineer-in-charge.

S&F in repairs 100 mm bore cast iron bends, (any radius) with duck's foot or heel rest complete all as specified & directed by Engineer-in-charge.

S&F 100mm bore (sand cast pipe) soil, waste and vent pipes in any length with or without ears and jointing with lead & fixed to walls complete all as specified & directed by Engineer-in-charge. Note:-lead joint will be measured and paid saperately

S&F 100mm bore (sand cast pipe) soil, waste and vent pipes in any length with or without ears and jointing with lead & laid in trenches or in floors complete all as specified & directed by Engineer-in-charge. Note:-lead joint will be measured and paid saperately

S&F in repairs100mm bore cast iron cowl (sand cast) complete all as specified & directed by Engineer-in-charge.

M&L Lead joints for 100 mm bore cast iron (sand cast pipe) and fittings complete all as specified & directed by Engineer-in-charge.

M&L preparing new or previously untreated wood and wood based surfaces of any description otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint (Ordinary tint) over a coat of pink primer complete all as specified and directed by Engineer-in-charge.

M&L preparation of old steel surface of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint (ordinary tint) complete all as specified & directed by Engineer in charge.

M&L preparation of new or previously untreated steel surface of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint (ordinary tint) over a coat of red- oxide, zinc chrome primer complete all as specified & directed by Engineer-in-charge.

M&L preparation of new plastered surfaces of walls and applying two coats of distemper oil emulsion paint of approved tint over a coat of primer complete all as specified & directed by Engineer-in-charge.

M&L preparation of new plastered surfaces of wall and applying two coats of cement base paint over one coat of primer complete all as specified and directed by Engineer-in-charge.

M&L preparation of new plastered surfaces of ceiling and applying two coats of white wash complete all as specified & directed by Engineer-in-charge.

S&F Rolled Mild Steel Sections Like Angle, Channel, Flat etc as inframed work such as grills, gratings, etc, with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framed work of water tanks and similar work confirming to Fe-290 Gde E-165 complete all as specified & directed by Engineer-in-charge.

HOODA CONSTRUCTION COMPANY

vinayandsons