Interior renovation, refurbishment including MEP works for Vijay Deep Building for Mumbai Port Authority (MbPA)at Shoorji Vallabhdas Marg, Ballard State, Mumbai-400001

GRAND TOTAL 23,42,51,834.64

3 6.47 Providing and laying Autoclaved Aerated concrete(AAC) blocks masonry with 150mm to 300 mm Cu.m 8,333.65 10.00 83,336.50

thick with Grade-1 AAC blocks of density 551 to 650 kg/cum conforming to IS:2185 (Part 3) in super

structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved

block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge.

(The payment of RCC band and reinforcement shall be made for seperately).

4 PWD SSR Providing and fixing chicken mesh of 22 gauge, with about 30 cm. width at the junction of R.C.C Rmt 70.62 100.00 7,062.30

2022-23 members and brick work, of approved quality including fixing mesh in position by necessary

32.26 drilling in concrete /B.B.masonry and or tying by binding wire etc. complete.

5 PWD SSR Providing and applying one pack bonding coat between concrete members like RCC slabs, columns, Sq.m 66.91 1,483.00 99,221.60

2022-23 beams, chajjas, pardis etc and cement mortar plaster of approved make & approved by Engineer in

50.09 charge. Clean the concrete surface thoroughly to remove dust, dirt, grime, deshuttering oils and rub

down to a clean surface. Apply bonding coat of approved make & approved by Engineer in charge by

spray on the entire concrete surface. Provide a lean cement - sand dash coat over the same. Allow the

dash coat to set for around 24 hours. Further plastering as per specifications can continue.

6 NS- 1 Providing and applying factory manufactured ready mix cement plaster of approved make, 12 mm Sq.m 527.50 500.00 2,63,750.00

average thickness, consisting of free flowing granular grey premixed material with selective processed

sand, mixed with clean water in proportion as recommended by manufacturer (approx. 6.8 to 7.6 litres

per 40 kg bag), having compressive strength not less than 8 MPa, flexural strength not less than 2 MPa,

pull out bond strength not less than 0.3 MPa, including surface preparation, hacking/raking of joints

wherever required, scaffolding, mixing, application, finishing true to line, level and plumb, curing for

minimum 3 days, and all labour, materials, tools & plants complete as per manufacturer’s specifications

and direction of Engineer-in-Charge.

7 13.78 Providing and applying 12 mm thick (average) premixed formulated one coat gypsum lightweight Sq.m 468.90 1,483.00 6,95,378.70

plaster having additives and light weight aggregates as vermiculite/ perlite respectively conforming to

IS: 2547 (Part - 1 & II) 1976, applied on hacked / uneven background such as bare brick/ block/ RCC

work on walls & ceiling at all floors and locations, finished in smooth line and level etc. complete.

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

8 NS- 2 Providing and applying factory manufactured ready mix cement plaster of approved make, 20 mm Sq.m 873.75 10.00 8,737.50

average thickness, consisting of free flowing granular grey premixed material with selective processed

sand, mixed with clean water in proportion as recommended by manufacturer (approx. 6.8 to 7.6 litres

per 40 kg bag), having compressive strength not less than 8 MPa, flexural strength not less than 2 MPa,

pull out bond strength not less than 0.3 MPa, including surface preparation, hacking/raking of joints

wherever required, scaffolding, mixing, application, finishing true to line, level and plumb, curing for

minimum 3 days, and all labour, materials, tools & plants complete as per manufacturer’s specifications

and direction of Engineer-in-Charge.

13.37 White washing with lime to give an even shade : -

9 13.37.1 New work (three or more coats) Sq.m 39.05 2,448.00 95,594.40

13.85 Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile -

Organic Compound ) content.

10 13.85.3 With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre Sq.m 73.95 3,056.00 2,25,991.20

11 13.8 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and Sq.m 156.05 3,056.00 4,76,888.80

manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

13.83 Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic -

Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying

additional coats wherever required to achieve even shade and colour.

13 NS- 3 Providing and applying premium grade decorative interior texture paint of approved make, shade, Sq.m 640.20 100.00 64,020.00

colour and texture, over properly prepared, putty-finished and primer-coated surfaces, including

application of approved texture coating in the specified pattern/profile using suitable tools, rollers,

trowels or spray equipment as required, achieving uniform texture, colour, thickness and finish as per

approved sample/mock-up and manufacturer's recommendations; including all necessary masking,

protection of adjoining surfaces, preparation of texture material, application in required number of

coats/layers, levelling and finishing, touch-ups and making good minor surface imperfections, complete

with all labour, scaffolding/access arrangements, tools, tackles and incidental materials, complete in all

respects as directed by the Engineer-in-Charge/Architect.

13.47 Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: -

14 13.47.1 New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior Sq.m 171.10 10.00 1,711.00

primer applied @ 0.90 litre/10 sqm)

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

15 PWD SSR Providing and applying Texture plaster with finishing with texture material of approved make in Sq.m 778.09 10.00 7,780.92

2022-23 3 to 4 millimeter thickness on previously plastered surface, including Plaster Groove 6mm thickness

32.32 or Tape Grooves 35 to 45 mm thickness or as required, in all position including preparing the

surface, scaffolding etc. complete.

16 PWD SSR Providing and applying Elastomeric, Anti carbonation, Anti corrosive, UV resistant, Solvent based Sq.m 646.76 - -

2022-23 Pure Aliphatic Acrylate System- on the exterior faces of Buildings Protection against ION penetration,

47.19 carbonation,UV radiations and wethering effect conforming to ASTM D 4541-02 having

Electrochemical impedance of 107 Ω and achieving dry film thickness of minimum 200 microns in a

primer coat followed by two top coats using brush or spray after complete cleaning & removal of oil,

grease or loose particles from the surface etc. complete

22.7 Providing and laying integral cement based water proofing treatment including preparation of surface

as required for treatment of roofs, balconies, terraces etc consisting of following operations:

(a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing

compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including

adjoining walls upto 300 mm height including cleaning the surface before treatment.

(b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of

cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS

: 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1

cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved

by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height

including rounding of junctions of walls and slabs.

(c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of

cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-

(d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand)

admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge

including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the

surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep.

(e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for

curing and for final test.“All above operations to be done in order and as directed and specified by the

Engineer-in-Charge :

17 22.7.1 With average thickness of 120 mm and minimum thickness at khurra as 65 mm. Sq.m 1,684.60 - -

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

18 PWD SSR Providing waterproofing in W.C. and bath including brick bat coba in all position including providing Cu.m 8,194.10 - -

2022-23 and laying 12mm bedding in cement mortor 1:3 on vergin concrete slab with waterproofing

31.26 compound @ 1Kilogram/per bag of cement laying brick bat coba of required thickness in cm 1:5 with

waterproofing compound 1 Kilogram/bag of cement grouting and finishing the top layer with 20mm

thick brick bedding in cm mortor 1:3 with waterproofing compound 1 Kilogram/per bag of cement and

testing the treated portion for 48 hours by pond test and covering ten years' guarantee on requisite

stamp paper including curing etc. complete.

19 PWD SSR Waterproofing Treatment to plastered surface of toilet & bathroom walls minimum up to 90 cm Sq.m 557.55 - -

2022-23 (Dado) by using 2-(methoxycarbonyl)-1-propene-Butyl-2 propenoate (MPBP) based polymeric

52.23 waterproofing solution as approved by Engineer in charge. Clean the entire surface thoroughly and

over this prepared surface, apply three coats of 2-(methoxycarbonyl)-1-propene-Butyl-2 propenoate

(MPBP) based polymeric waterproofing solution as approved by Engineer in charge.While the 3 coat is

wet broadcast sand on the surface. Provide 20 mm thick cement plaster in CM 1:3 with one pouch of

330 grams of thorough blend of special cements, aldehyde based polymers, shrinkage compensating

agents as approved by Engineer in charge per 50 Kg bag of cement including all lead, lifts ,curing etc

complete. Acrylic Polymeric Waterproofing Coating for Concrete and Masonry should have following

minimum properties:

1. Elongation % (ASTM D412-2016): @ 100%

2. Tensile Strength N/mm2 (ASTM D412-2016): 3.3

3. Specific Gravity: 1.02 ± 0.02

4. Total Solids (ASTM D1644-2012): 43.98

5. Hardness Shore A (ASTM D2240-2015): 82

It shall be applied as per manufacturer’s specification.

20 22.22 Providing and mixing integral crystalline admixture for water proofing treatment to RCC structures Kg 388.00 - -

like basement raft, retaining walls, reservior, sewage & water treatment plant, tunnels / subway and

bridge deck etc. at the time of transporting of concrete into the drum of the ready-mix truck , using

integral crystalline admixture @0.80% (minimum) to the weight of cement content per cubic meter of

concrete) or higher as recommended by the manufacturer's specification in reinforced cement

concrete at site of work. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e.

by reducing permeability of concrete by more than 90%, compared with control concrete as per DIN

1048 and resistant to 16 bar hydrostatic pressure. The crystalline admixture shall be capable of self-

healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per

specification and the direction of the Engineer-in-charge. The product performance shall carry

guarantee for 10 years against any leakage.

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

22.23 Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment

to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior,

sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the

ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts

integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative

(internal) side with the help of synthetic fiber brush. The material shall meet the requirements as

specified in ACI-212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared

with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side.

The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall

be carried out all complete as per specification and the direction of the engineer-in-charge. The

product performance shall carry guarantee for 10 years against any leakage.

21 22.23.1 For vertical surface two coats @ 0.70 kg per sqm per coat Sq.m 472.90 - -

22 22.23.2 For horizontal surface one coat @1.10 kg per sqm. Sq.m 362.80 - -

23 PWD SSR Providing and applying a base coat comprising of 1KilogramPolydee-MC and Sq.m 1,569.81 - -

2022-23 1Kilogramfresh cement after wetting the surface followed by drying the surface for 2 days, apply

31.11 primer coat of TP-40 and after drying, applying Polydee-11 two component (mixing ratio 2 A : 1 B) )

Antibacterial food grade coating inside drinking water tank in two coats with time interval of minimum

8 hrs. covering 7 years guarantee on Court Fee Stamp Paper of Rs. 100/- etc. complete.

24 PWD SSR Providing and applying epoxy paint primer with middle coat and top coat to superstructure including Sq.m 861.11 10.00 8,611.05

2022-23 scaffolding etc complete.

11.26 Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry -

mixed with pigment to match the shade of the slab, including rubbing and polishing complete with

base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :

26 11.27 Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick Sq.m 2,354.70 84.00 1,97,794.80

cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment

to match the shade of the slabs, including rubbing and polishing complete.

27 11.31 Extra for pre finished nosing in treads of steps of Kota stone/ sand stone slab. metre 191.40 152.00 29,092.80

28 11.32 Extra for Kota stone/ sand stone in treads of steps and risers using single length above normal size up Sq.m 44.15 46.00 2,030.90

29 8.6 Mirror polishing on marble work/Granite work/stone work where ever required to give high gloss Sq.m 506.70 337.00 1,70,757.90

finish complete.

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

11.41A Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the -

manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand

& manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse

sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement

and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying

of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and

rubber mallet for placing the tiles gently and easily. (3mm spacer to be provided as per drawing and

nothing shall be paid extra for this)

11.41A.1 Double charge vitrified tile polished finish of size -

31 NS- 4 Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the Sq.m 2,541.00 1,547.00 39,30,927.00

manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand

& manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse

sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement

and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying

of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and

rubber mallet for placing the tiles gently and easily. (3mm spacer to be provided as per drawing and

nothing shall be paid extra for this) Size- 1200x1200 mm

11.41A.3 Glazed Vitrified tiles Matt/Antiskid finish of size -

33 NS- 5 Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), Sq.m 1,873.75 1,039.00 19,46,826.25

with water absorption less than 0.08% and conforming to IS: 15622, of approved brand &

manufacturer, in all colours and shade, in wall dado & Skirting laid with cement based high polymer

modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness,

including grouting of joints (Payment for grouting of joints to be made separately). (3mm spacer to be

provided as per drawing and nothing shall be paid extra for this)

Size of Tile 600x600 mm

34 NS- 6 Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), Sq.m 2,856.55 36.00 1,02,835.80

with water absorption less than 0.08% and conforming to IS: 15622, of approved brand &

manufacturer, in all colours and shade, in wall dado & Skirting laid with cement based high polymer

modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness,

including grouting of joints (Payment for grouting of joints to be made separately).(3mm spacer to be

provided as per drawing and nothing shall be paid extra for this)

Size of Tile 1200x1200 mm

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

35 NS- 7 Providing and laying Large Format Colour Body Sintered Surface Flooring using UNITERRA tiles/slabs of Sq.m 8,273.30 270.00 22,33,791.00

approved shade, texture, pattern and finish, size 1190 × 2400 / 2800 mm (or approved equivalent

large format as per design), 9 mm thick, colour body construction, manufactured using AI DIGI+

Technology and advanced sintered surface technology, having very low water absorption, high

flexural strength, excellent scratch resistance, stain resistance and UV stability.

The flooring shall be laid over an average 25–30 mm thick cement mortar bedding in CM 1:4 (1 cement

: 4 coarse sand), including preparation and dressing of base surface to required line, level and slope,

application of approved high-performance polymer modified adhesive suitable for large format

sintered slabs, laying, positioning, alignment, levelling, edge matching, mechanical handling, cutting,

trimming, tapping and adjustment to achieve true plane and uniform finish.

The item shall include treatment and filling of joints with approved matching grout, cleaning of finished

surface, protection during execution and handover, curing wherever required and execution complete

in accordance with manufacturer’s specifications, approved shop drawings and Architect’s instructions.

Rate shall include cost of all materials, labour, cement mortar bedding, adhesive, grout, cutting and

wastage, edge finishing, loading, unloading, transportation, lifting to all levels, tools & tackles,

machinery, scaffolding wherever required and all incidental works complete in all respects. .(3mm

spacer to be provided as per drawing and nothing shall be paid extra for this) (Tile basic rate : 350

36 NS- 8 Providing and laying Large Format Colour Body Sintered Surface DADO using UNITERRA tiles/slabs of Sq.m 8,084.60 323.00 26,11,325.80

approved shade, texture, pattern and finish, size 1190 × 2400 / 2800 mm (or approved equivalent

large format as per design), 9 mm thick, colour body construction, manufactured using AI DIGI+

Technology and advanced sintered surface technology, having very low water absorption, high

flexural strength, excellent scratch resistance, stain resistance and UV stability.

The Dado shall be laid over plastered surafce with application of approved high-performance polymer

modified adhesive suitable for large format sintered slabs, laying, positioning, alignment, levelling,

edge matching, mechanical handling, cutting, trimming, tapping and adjustment to achieve true plane

and uniform finish.

The item shall include treatment and filling of joints with approved matching grout, cleaning of finished

surface, protection during execution and handover, curing wherever required and execution complete

in accordance with manufacturer’s specifications, approved shop drawings and Architect’s instructions.

Rate shall include cost of all materials, labour, adhesive, grout, cutting and wastage, edge finishing,

loading, unloading, transportation, lifting to all levels, tools & tackles, machinery, scaffolding wherever

required and all incidental works complete in all respects.(3mm spacer to be provided as per drawing

and nothing shall be paid extra for this (Tile basic rate : 350 Rs/sq.ft)

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

37 R3-CS-CH- Providing and fixing Pattern tiles of 23-25mm thick Bharat Tiles or equivalent of Sq.m 9,503.72 - -

27 approved colours and cut to shape of approved patterns & grinding edges filling

joints as per manufacturer's specifications and including 25 mm thick bedding

mortar,grouting,watering,curing,cleaning,polishing etc. complete as directed by the Architect. (Tile

basic rate : 375 Rs/sq.ft)

38 R3-CS-CH- Providing & Laying 20-25 mm thk Plain Bharat Tiles or equivalent cement tile for Rmt 7,041.06 - -

29 border as per design. The border design to be broken up into 3-4 components in

different colours upto a maximum of 4 colours and pattern inserts indicated by

the architect as per drawing in cement mortar 1.5 to 3.5 cm cement : sand bed mortar of 36 grade

cement of ratio not leaner than 1:4 with a neat cement slurry on top, of approved thickness. Joints

should be as fine as possible and filled with matching cement mortar as directed by architects. (Tile

basic rate : 375 Rs/sq.ft)

39 R3-CS-CH- Providing and laying of Bharat Tiles or Equivalent make cement tiles skirting of Rmt 1,276.76 - -

30 100mm ht. using Plain tiles (plain colour including all the range (dark, light or

premium) as available with the manufacturer) 17-20 mm thick. Item complete with 20-25mm thick

cement mortar 1:4 and finishing with 6mm groove at the junction between skirting and wall etc. Rate

to be inclusive of tile,storage,all duties and taxes applicable. (Tile basic rate : 375 Rs/sq.ft)

40 NS- 9 Providing and laying machine cut, mirror polished 18 mm thk Italian marble stone flooring, in required Sq.m 7,172.75 325.00 23,31,143.75

design (Simple geometrical, abstract etc.) and in patterns in combination with Italian marble stones of

different colours, shades and finished surface texture etc., in linear portions of the building, all

complete as per the architectural drawings, with 18 mm thick stone slab laid over 20 mm (average)

thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with approved stone

adhesive, including pointing with epoxy grout match the marble shade, including rubbing, curing and

polishing etc. all complete as specified and as directed by the Engineer-in-Charge. (Epoxy grouting shall

be paid seperately) (Basic rate- 350 Rs/Sq.ft)

41 NS- 10 Extra over the basic item of Italian marble flooring for providing and executing decorative marble Sq.m 4,267.90 40.26 1,71,808.58

inlay work, comprising precision cutting and shaping of approved contrasting Italian marble pieces to

form decorative patterns, borders, motifs, geometric designs or other approved inlay designs, including

preparation of templates, water-jet/CNC cutting wherever required, selection and matching of marble

for colour, shade and veining, accurate positioning and setting of inlay pieces in the marble flooring,

fixing with approved adhesive/bedding material, filling and finishing of joints, grinding, honing and

polishing to achieve a smooth, level and seamless finish with the adjoining marble flooring, including all

additional labour, cutting, wastage, consumables, tools, tackles and incidental works necessary for

complete execution of the approved inlay design

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

42 NS- 11 Providing and laying machine cut, mirror polished 18 mm thk Italian marble stone dado, in required Sq.m 10,154.70 633.00 64,27,925.10

design (Simple geometrical, abstract etc.) and in patterns in combination with Italian marble stones of

different colours, shades and finished surface texture etc., in linear portions of the building, all

complete as per the architectural drawings, with 18 mm thick stone slab laid over plastered surface and

jointed with approved stone adhesive, including pointing with epoxy grout match the marble shade,

including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-

Charge. (Epoxy grouting shall be paid seperately) (Basic rate- 350 Rs/Sq.ft)

43 NS- 12 Providing and laying machine cut, mirror polished 18 mm thk engineered/natural quartz stone slabs of Sq.m 9,284.05 20.00 1,85,681.00

different colours, shades and finished surface texture etc., , all complete as per the architectural

drawings, with 18 mm thick stone slab laid over plastered surface and jointed with approved stone

adhesive, including pointing with epoxy grout match the marble shade, including rubbing, curing and

polishing etc. all complete as specified and as directed by the Engineer-in-Charge. (Epoxy grouting shall

be paid seperately) (Basic rate- 350 Rs/Sq.ft)

44 NS- 13 Sealer Coat : Providing and applying solvent-based, impregnating stain-resistant protective treatment Sq.m 675.75 958.00 6,47,368.50

using Ultracare Stain Protector S , on natural stone, marble, granite, terrazzo and cementitious

surfaces, to protect against oil and water-based stains without forming a surface film and without

altering the natural appearance of the substrate.

The item shall include:

Cleaning of surface by mechanical/manual means to remove dust, dirt, grease, laitance and all foreign

materials. Ensuring the substrate is dry, sound and free from moisture prior to application. Application

of the treatment uniformly by brush/roller/low-pressure spray to achieve proper penetration into the

substrate. Removal of excess material after application to avoid surface residue or film formation.

Application of additional coat(s), if required, depending on porosity of the substrate, as per

manufacturer’s specifications. Final wiping/buffing to achieve uniform appearance. Protection of

treated surface from dust, dirt, moisture and traffic during application and curing period. All materials,

labour, tools & tackles, scaffolding (if required), and sundries complete as per specifications and

directions of Engineer-in-Charge.

11.56 Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well -

as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick

stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and

jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching

shade including rubbing , curing and polishing etc. all complete as specified and as directed by the

Engineer-in-Charge.

45 11.56.1 Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent Sq.m 4,481.30 551.00 24,69,196.30

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

46 NS- 14 Providing and laying Polished River washed Granite stone flooring in required design and patterns, in Sq.m 5,009.40 50.00 2,50,470.00

linear as well as curvilinear portions of the building all complete as per the architectural drawings with

18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse

sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment

of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed

by the Engineer-in-Charge.

47 NS- 15 Providing and fixing polished River Washed Granite stone for treads and risers of staircases in Sq.m 5,332.35 25.00 1,33,308.75

required widths, lengths and profiles, including 18 mm thick granite stone for treads and risers,

machine-cut with rounded/chamfered nosing, anti-skid grooves on treads as per approved design, edge

polishing, cutting, dressing and moulding wherever required, laid over 20 mm (average) thick bed of

cement mortar 1:4 (1 cement : 4 coarse sand), jointed with cement slurry and pointed with white

cement slurry admixed with pigment of matching shade, including rubbing, curing, polishing, making

openings, cutting to shape, finishing exposed edges and all incidental works complete as per approved

drawings, specifications and directions of the Engineer-in-Charge.

8.10 Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep -

and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter

and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2

coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and

finished smooth.

48 8.10.2 Granite Stone of approved shade Sq.m 4,051.85 5.00 20,259.25

49 16.90 Providing and laying tactile tile (for vision impaired persons as per standards) of size 300x300x9.8mm Sq.m 2,017.60 50.00 1,00,880.00

having with water absorption less than 0.5% and conforming to IS:15622 of approved make in all

colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on

20mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) in all shapes & patterns including

grouting the joints with white cement mixed with matching pigments etc. complete as per direction of

Engineer-in-Charge.

50 R3-CS-FL- TELEPHONE BLACK GRANITE WASH HAND Rmt 11,755.16 17.00 1,99,837.72

88 BASIN COUNTER : Providing and making wash basin counter in single piece of 18 mm to 20 mm thk.

Telephone Black granite 600 mm side fixed over 25 to 40 mm thk. Black Cuddappa, stand with type

construction,by making zari, in walls upto 75 mm deep & fitting the wall surface by C.M. 1:2 with

necessary moulding,profile cutting in granite and cudappa including making hole to receive pillar cock

for wash basin etc complete and as per detailed

51 PWD SSR Providing and constructing granite kitchen platform with fixing of stainless steel sink 600 mm x 450 Sq.m 12,175.65 12.00 1,46,107.84

2022-23 mm size as per detailed drawing including vertical both side polished kadappah stone 25 to 30 mm

41.78 thick supports with kadappah top 35 to 40 mm thick and polished granite 16 to 20 mm top with side

strips of granite at front and both sides of platform raised with two vertical granite supports 15 cm

height and top granite of 75 x 40 cm including cutting, opening for sink of required size in

kadappah as well as granite etc. complete

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

52 PWD SSR Providing and fixing machine cut machine polished 18 mm to 20 mm thick telephone black / Amba Sq.m 5,169.11 119.00 6,15,123.85

2022-23 White / Cat bary brown / RBI red / Ocean Brown granite stone for treads and risers of steps and

33.35 staircases of approved colour and shade with full moulding and three grooved line for the treads on

bed of 1:4 Cement mortar including float filling joints with neat cement slurry curing polishing and

cleaning etc. complete.

53 PWD SSR Providing and laying telephone black / Amba White / Cadburybrown / Ruby red / Ocean Brown Sq.m 5,442.40 76.00 4,13,622.37

2022-23 granite stone of 18 to 20 mm thick for door frame/ dado/ window boxing etc. On C.M. 1:6 including

33.68 filling joints with polymer base filler nosing/moulding the sharp edges wherever necessary, curing, etc.

54 Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of Sq.m 275.41 4,419.00 12,17,047.84

11.48 organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling /

grouting and finishing complete as per direction of Engineer-in-charge.

55 NS- 16 Providing and fixing decorative metal inlay/insert of approved grade Stainless Steel (SS 316) , of Rmt 853.60 100.00 85,360.00

approved finish (mirror, brushed, matt, antique, PVD, hairline or as approved), width, thickness and

profile as per approved drawings, accurately cut, shaped and fixed flush with adjacent finished surfaces

using approved adhesive, mechanical fasteners and accessories wherever required, including cutting

grooves, alignment, polishing, cleaning, protection and all incidental works complete as directed by the

Engineer-in-Charge

56 NS- 17 Providing and fixing decorative metal inlay/insert of approved Solid Brass, of approved finish (mirror, Rmt 1,202.15 100.00 1,20,215.00

brushed, matt, antique, PVD, hairline or as approved), width, thickness and profile as per approved

drawings, accurately cut, shaped and fixed flush with adjacent finished surfaces using approved

adhesive, mechanical fasteners and accessories wherever required, including cutting grooves,

alignment, polishing, cleaning, protection and all incidental works complete as directed by the Engineer-

57 NS- 18 Supplying and laying approved carpet tiles, 500 mm × 500 mm, made of solution-dyed nylon with pile Sq.m 4,267.90 50.00 2,13,395.00

height of 4–5 mm and minimum total weight of 4000 GSM, having StableShield backing or approved

equivalent. The rate shall include supply of all materials, labour, approved adhesives, fixing accessories,

cutting, fitting, trimming, wastage, transportation, handling, surface preparation, cleaning, and all

incidental works required for complete installation and proper finishing, in accordance with the

approved drawings, manufacturer's specifications, and the directions of the Engineer/Architect,

complete in all respects (Basic rate - 220 Rs/Sq.ft)

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

58 NS- 19 Providing, supplying and laying Area Rug of approved make, design, colour, pattern and texture, Sq.m 28,452.75 50.00 14,22,637.50

suitable for heavy commercial office use, machine tufted/hand tufted as specified, with minimum pile

height of 8–12 mm, anti-skid backing, stain-resistant and fade-resistant properties, complete with edge

binding, cutting to required shape and size, placing in position, including transportation, handling, all

incidental materials and accessories, complete as per approved drawings and as directed by the

Engineer-in-Charge (Basic rate - 1500 Rs/Sq.ft)

59 NS- 20 Providing and laying Premium Engineered Oak Wood Flooring (Classic Range) of approved make, Sq.m 12,092.40 - -

colour, grade and finish, comprising a 13 mm thick dimensionally stable 3-layer engineered

construction with minimum 2.5 mm thick genuine Oak wood wear layer, solid softwood core and

balancing veneer backing, factory manufactured and factory finished with UV-cured matt lacquer, extra

matt lacquer or natural oil finish, complete as specified.

The flooring shall comprise Living Grade Oak (or Natur/Rustic Grade where specified), 13 mm overall

thickness, minimum 2.5 mm Oak wear layer, plank size approximately 2200 × 185 mm, 4-sided micro

bevel (M4V) edges, smooth/brushed/lightly textured surface as approved, and shall be factory

conditioned for dimensional stability. The flooring shall be installed using a precision click-lock system

for floating installation or full-surface bonded installation with approved elastic wood flooring

adhesive, strictly in accordance with the manufacturer's recommendations.

The work shall include preparation and checking of the substrate, approved acoustic underlay or elastic -

adhesive as specified, installation by trained applicators, provision of matching engineered wood

skirting, reducers, T-profiles, end trims, stair nosings, thresholds and all proprietary accessories,

formation of expansion gaps and movement joints, cutting and fitting around columns, door frames

and service penetrations, complete cleaning, protection of finished flooring and making good all

disturbed finishes.

The flooring system shall be suitable for interior applications, compatible with approved underfloor

heating/cooling systems where recommended by the manufacturer, and shall be supplied complete

with all accessories required for a complete installation. The product shall carry a minimum 25-year

residential warranty and 10-year commercial warranty against manufacturing defects, complete in all

respects as per the approved drawings, manufacturer's specifications and directions of the Engineer-in-

Charge (Basic rate- 850 Rs/Sq.ft)

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

60 NS- 21 Providing and laying Premium Laminate Flooring (Classic Range) of approved make, colour, shade, Sq.m 5,406.00 - -

texture and finish, comprising minimum 8 mm thick High Density Fibreboard (HDF) core board with

decorative impregnated paper layer and transparent abrasion-resistant overlay, factory manufactured

and finished complete as specified.

The laminate flooring shall have minimum 8 mm thickness (9 mm where specified), plank size

approximately 2200 mm long or approved equivalent, Class 23 Residential and Class 33 Heavy

Commercial wear classification, minimum AC5 abrasion resistance, minimum 48-hour water resistance,

moisture-resistant HDF core with edge impregnation, 4-sided V-groove (4V) edges, and a micro scratch-

resistant, anti-static and stain-resistant surface finish. The flooring shall be installed using a factory-

engineered angle-click/click-lock floating system (Safe-Lock® Pro or approved equivalent) without

adhesive and shall be compatible with approved acoustic underlay and underfloor heating/cooling

systems where recommended by the manufacturer. The product shall comply with recognised low VOC

indoor air quality standards such as Blue Angel, FloorScore, A+, GREENGUARD Gold or equivalent.

The work shall include supply and installation of approved acoustic/moisture barrier underlay, floating -

installation over a prepared and level substrate, matching skirting boards, reducers, T-profiles, end

trims, stair nosings, thresholds and all proprietary accessories, provision of expansion gaps and

movement joints, cutting and fitting around columns, door frames and service penetrations, cleaning,

protection of completed flooring until handover, and making good all disturbed finishes.

The laminate flooring shall be installed strictly in accordance with the manufacturer's written

recommendations and approved drawings, complete in all respects, and shall carry a minimum Lifetime

Residential Warranty and 10-year Commercial Warranty against manufacturing defects. (Basic rate -

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

61 NS- 22 Providing and fixing homogeneous vinyl flooring of 2.00 mm thickness in roll size 2.00 m × 20.00 m, Sq.m 2,560.75 25.00 64,018.75

laid over a clean, smooth and properly prepared subfloor using approved adhesive, including cutting,

jointing, heat welding of seams, finishing at edges and all incidental works complete. The flooring shall

be anti-fungal, anti-bacterial, termite and bug resistant, possess superior stain, scratch, fire and

chemical resistance, require zero maintenance, be easy to clean with soap and water, and have a

factory-applied PUR (Polyurethane Reinforcement) wear layer. The product shall be phthalate-free,

have zero VOC emissions, and be suitable for high-traffic commercial, institutional and healthcare

The product shall be manufactured in India, conform to ISO 10582 for PVC flooring, comply with

applicable BIS standards, be FloorScore® certified for Indoor Air Quality (IAQ), comply with EN 649

Group T, ISO 24346 (EN 428) for thickness, DIN 51130, EN 13893 and ASTM D2047 for slip resistance,

ISO 23999 (EN 434) for dimensional stability, ISO 24344 (EN 435) for flexibility, ASTM F137 for crack

resistance, ISO 16906 for seam strength, ISO 24343-1 (EN 433), ASTM F970 and ASTM F1914 for

residual indentation, EN ISO 105-B02 and ASTM F1515 for colour fastness to light, EN 12667 for

thermal resistance, ASTM F1514 for heat stability, EN ISO 9239-1, EN ISO 11925-2, EN 13501-1, ASTM

E648 Type I and ASTM E662 for fire and smoke performance, ISO 26987 (EN 423) and ASTM F925 for

stain and chemical resistance, ISO 846 (Methods A & C) for resistance to fungi and bacteria, and comply

with IMO Resolution A.653(16) Annex 1 Part 2 (Smoke & Toxicity), IMO MSC.61(67) Part 5 (Spread of

Flame), and the Marine Equipment Directive (MED). The rate shall include supply of all materials,

approved adhesive, heat welding rods, labour, cutting, jointing, welding of seams, finishing,

transportation, tools and tackles, and all other incidental works required for complete installation as

directed by the Engineer-in-Charge

62 NS- 23 Providing and fixing Luxury Vinyl Tile (LVT) flooring of 2.0 mm thickness in tile size 610 mm × 610 mm Sq.m 2,845.25 25.00 71,131.25

(24" × 24"), in approved carpet finish/design, laid over a clean, smooth and properly prepared subfloor

using recommended adhesive, including cutting, fitting, finishing at edges and all incidental works

complete. The LVT shall be termite and bug resistant, possess superior stain, scratch, fire and chemical

resistance, require zero maintenance, be easy to clean with soap and water, and have a factory-applied

UV-treated PUR (Polyurethane Reinforcement) wear layer. The product shall be phthalate-free,

manufactured in India, conform to ISO 10582 for Luxury Vinyl Tiles, comply with applicable BIS

standards, be FloorScore® certified for Indoor Air Quality (IAQ), and CE certified conforming to EN

14041. It shall comply with EN ISO 10874, EN ISO 24346 (EN 428), EN ISO 24340 (EN 429), EN ISO 23997

(EN 425), EN ISO 10456, EN ISO 105-B02, EN ISO 26987 (EN 423) and DIN 51130, and shall meet fire

performance requirements of IMO Resolution A.653(16), IMO MSC.61(67) and EN 13501-1 with

minimum classification Bfl-s1 when glued over an A2fl concrete substrate. The rate shall include supply

of all materials, approved adhesive, labour, cutting, fitting, finishing, wastage, transportation, tools and

tackles, and all other incidental works required for complete installation, complete as directed by the

Engineer-in-Charge

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

63 NS- 24 Providing and fixing PVC Sports Flooring of 4.50 mm thickness in rolls of 1.80 m × 20.00 m, laid over a Sq.m 3,414.35 - -

clean, smooth and properly prepared subfloor using approved adhesive, including cutting, jointing,

welding of joints wherever required, finishing at edges and all incidental works complete. The flooring

shall be termite and bug resistant, possess superior stain, scratch, fire and chemical resistance, require

zero maintenance, be easy to clean with soap and water, and have a factory-applied PUR (Polyurethane

Reinforcement) wear layer. The product shall be phthalate-free, have zero VOC emissions, and provide

superior dimensional stability and indentation resistance. The flooring shall be suitable for professional

sports facilities, multipurpose halls, gymnasiums, kindergartens and similar applications requiring

athletic performance, safety, energy absorption, noise reduction and durability.

The product shall be manufactured in India, conform to ISO 10582 for PVC flooring, comply with

applicable BIS standards, be FloorScore® certified for Indoor Air Quality (IAQ), and comply with EN 651

Class 23, EN 428, EN ISO 717-2 / EN ISO 140-8 for impact sound insulation, EN 13501-1 for flammability,

EN 13036-4 for rotational friction, DIN 18032, EN 14808 for shock absorption, EN 14809 for vertical

deformation, EN 12235 for ball rebound, EN 2813 for specular gloss, EN 434 for dimensional stability,

EN 1516 for indentation resistance, EN 1569 for resistance to rolling load, ISO 105-B02 for colour

fastness, EN 423 for chemical resistance, EN ISO 5470-1 for abrasion resistance (H18 wheel), EN 660-2

Group T for abrasion classification, and comply with IMO Resolution A.653(16) and IMO MSC.61(67) for

fire resistance. The rate shall include supply of all materials, approved adhesive, labour, cutting,

jointing, welding of seams, finishing, transportation, tools and tackles, and all other incidental works

required for complete installation as directed by the Engineer-in-Charge

64 NS- 25 Providing and fixing rubber flooring of 25 mm thickness in tile size 500 mm × 500 mm, manufactured Sq.m 3,058.65 - -

from high-density vulcanized rubber, in approved colour and finish, laid over a clean, smooth and

properly prepared subfloor using approved polyurethane/rubber flooring adhesive as recommended

by the manufacturer, including cutting, fitting, alignment, finishing at edges, and all incidental works

complete. The flooring shall be slip resistant, impact absorbing, anti-skid, wear resistant, durable, easy

to clean and maintain, and suitable for gymnasiums, fitness centres and other high-impact applications.

The rate shall include supply of rubber tiles, approved adhesive, labour, cutting, fitting, transportation,

tools and tackles, and all other materials and operations required for complete installation as directed

by the Engineer-in-Charge

65 R3-CS-PN- Providing and applying antifungal self leveling 3mm EPU system including coving at floor wall junction, Sq.m 1,562.32 - -

25 necessary surface preparation by cleaning and de-dusting. The System shall be executed in three

stages, firstly by applying a solvent free epoxy primer which has a volumetric ratio of mixing @ 200

microns dft, then laying 1.8mm self leveling epoxy based screed and finally applying a solvent free EPU

( epoxypolyurethane), self leveling coating to yield a dft of 1000 microns. The EPU coating shall be a

two component with volumetric ratio of mixing. No fillers shall be added at the site while laying the self

leveling EPU including Aisle or zone marking in different colours etc. complete as per manufacturers

specifications and as directed & approved by Engineer In-Charge.

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

66 NS- 26 Providing and fixing powder-coated aluminium skirting of 75 mm height, manufactured from Rmt 782.45 50.00 39,122.50

extruded aluminium sections of approved alloy and temper, with factory-applied powder-coated finish

in approved colour, fixed to walls using approved screws, clips, brackets, or adhesive as recommended

by the manufacturer, including cutting, mitre joints, internal and external corners, end caps, joining

accessories, alignment, sealing where required, and all incidental works complete. The rate shall

include supply of all materials, fittings, fasteners, labour, transportation, tools and tackles, and all

operations necessary for complete installation as directed by the Engineer-in-Charge

67 11.53 Providing and fixing Glass mossaic tiles on finished plain wall surface of size 20 mm x 20 mm x 4 mm Sq.m 3,891.15 - -

in all colour, design , fixing in customize design as per direction of Engineer-in- Charge. The glass mosaic

tiles to be fixed on the wall surface with the help of approved adhesive applied at the rate of 2.5 kg per

sqm and grouting of the same. The rate is inclusive of all operation, material and required pattern

approved by Engineer-in-Charge:

16.91 Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, -

lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by

table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted

bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand

bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and

cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all

as per direction of Engineer-in-Charge.

68 16.91.2 80 mm thick C.C. paver block of M-35 grade with approved colour design and pattern. Sq.m 1,091.50 586.00 6,39,619.00

11.54 Providing and fixing removable raised/false access flooring with system and its components of -

approved make for different plenum height with possible height adjustment upto 50 mm, comprising

of modular load bearing floor panels supported on G.I. rectangular stinger frame work and G.I. Pedestal

etc. all complete, as per the architectural drawings, as specified and as directed by Engineer-in-charge

(a) Providing at required spacing to form modular framework, pedestals made out of GI tube of -

thickness minimum 2 mm and 25 mm outer diameter, fully welded on to the G.I. Base plate of size

100mm x 100mm x 3mm at the bottom of the pedestal tube, G.I. pedestal head of size

75mmx75mmx3.5 mm welded with GI fully threaded stud 16mm outer diameter with two GI Check

nuts screwed on the stud for level adjustment upto 50mm, locking and stabilizing the pedestal head in

position at the required level. The pedestals shall be fixed to the subfloor (base) through base plate

using epoxy based adhesive of approved make or the machine screw with rawl plug.

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

(b) Stringers system in all steel construction hot dipped galvanized of rectangular size -

570x20x30x0.80mm thick having holes at both ends for securing the stringers on to the pedestal head

using fully threaded screws ensuring maximum lateral stability in all directions, the grid formed by the

pedestal and stringer assembly shall receive the floor panel, this system shall provide adequate solid,

rigid support for access floor panel, the system shall provide a minimum clear uninterrupted clearance

between the bottom of the floor for electrical conduits and wiring etc. all complete as per the

architectural drawings, as specified and as directed by the Engineer-in-charge.

(c) Providing and fixing Access Floor panel of 600x600x32 mm medium grade Filled Steel anti static -

high pressure Lamination of 800H grade (FS800H). Access Floor panel shall be steel welded

construction with an enclosed bottom pan with uniform pattern of 64 hemispherical cones. The top

and bottom plates of Steel Gauges: top 0.6 mm and bottom 0.7 mm fused spot welded together

(minimum 64 welds in each dome and 20 welds along each flange). The panel should be Corroresist

epoxy coated for lifetime rust protection and cavity formed by the top and bottom plate is filled with

Pyrogrip noncombustible Portland cementitious core mixed with lightweight foaming compound. The

access floor shall be factory finished with Anti-static High Pressure laminate with Non Warp technology

upto 1mm thickness for superior adhesion and Surface flatness within 0.75mm.The panel is to

withstand a Concentrated Load of 363 kgs applied on area 25mm x 25mm without collapse in the

centre of the panel which is placed on four steel blocks. The panel will withstand and Uniformly

Distributed Load (UDL) minimum 1250 kg/sqm and an impact load of 50kg all complete as per the

approved manufacturers specification and as per the direction of Engineer-in-charge. All specification

must be printed on the side of the panel to ensure the quality of the product.

69 11.54.1 300 mm Finished Floor Height (FFH) Sq.m 5,623.95 33.00 1,85,590.35

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

12.45 Providing and fixing false ceiling at all height including providing and fixing of frame work made of -

special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm

(both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick

with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with

dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle

hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle

hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre

to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26

mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular

to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at

every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm

and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm

centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling

section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c,

including jointing and finishing to a flush finish of tapered and square edges of the board with

recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers

covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per

manufacturer's specification and also including the cost of making openings for light fittings, grills,

diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings,

specification and direction of the Engineer in Charge but excluding the cost of painting with :

70 12.45.1 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS Sq.m 1,355.80 1,525.00 20,67,595.00

certification marks)

71 NS- 27 Providing and fixing decorative gypsum/POP moulding/cornice of approved profile, having projection Rmt 569.05 1,000.00 5,69,050.00

up to 25 mm, including preparation of templates, casting/manufacturing of mouldings, cutting, fitting,

fixing with approved adhesive and POP, filling joints, sanding, finishing, and preparing the surface ready

to receive paint, complete in all respects as per approved drawings, specifications, and directions of the

Engineer-in-Charge.

72 NS- 28 Providing and fixing decorative gypsum/POP moulding/cornice of approved profile, having projection Rmt 711.30 500.00 3,55,650.00

above 25 mm and up to 50 mm, including preparation of templates, casting/manufacturing of

mouldings, cutting, fitting, fixing with approved adhesive and POP, filling joints, sanding, finishing, and

preparing the surface ready to receive paint, complete in all respects as per approved drawings,

specifications, and directions of the Engineer-in-Charge.

73 NS- 29 Providing and fixing decorative gypsum/POP moulding/cornice of approved profile, having projection Rmt 853.60 500.00 4,26,800.00

above 50 mm and up to 100 mm, including preparation of templates, casting/manufacturing of

mouldings, cutting, fitting, fixing with approved adhesive and POP, filling joints, sanding, finishing, and

preparing the surface ready to receive paint, complete in all respects as per approved drawings,

specifications, and directions of the Engineer-in-Charge.

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

74 NS- 30 Providing and fixing decorative gypsum/POP moulding/cornice of approved profile, having projection Rmt 995.85 500.00 4,97,925.00

above 100 mm and up to 200 mm, including preparation of templates, casting/manufacturing of

mouldings, cutting, fitting, fixing with approved adhesive and POP, filling joints, sanding, finishing, and

preparing the surface ready to receive paint, complete in all respects as per approved drawings,

specifications, and directions of the Engineer-in-Charge

75 NS- 31 Providing and fixing decorative gypsum/POP moulding/cornice of approved profile, having projection Rmt 1,280.35 500.00 6,40,175.00

above 200 mm and up to 300 mm, including preparation of templates, casting/manufacturing of

mouldings, cutting, fitting, fixing with approved adhesive and POP, filling joints, sanding, finishing, and

preparing the surface ready to receive paint, complete in all respects as per approved drawings,

specifications, and directions of the Engineer-in-Charge

76 R3-CS-WW- Providing&fixing TRAP DOOR with T.W. frame work and shutter made from19mm marine plywood and Sq.m 7,865.88 5.00 39,329.40

43 exposed surface finished with 1.5mm laminateand internal surface finished with flat oil paint with s.s.

fittings & fixtures as per Architects detailed drg. and design.

12.52 Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal -

level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120

grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get

required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm

center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm

long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and

secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to

be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size

24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required

cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc.

Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed

to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised

butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom

exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all

heights as per specifications, drawings and as directed by Engineer-in-charge.

77 12.52.1 GI Metal Ceiling Lay in plain Tegular edge Global white color tiles of size 595x595 mm, and 0.5 mm Sq.m 1,902.95 426.00 8,10,656.70

thick with 8 mm drop; made of G I sheet having galvanizing of 100 gms/sqm (both sides inclusive) and

electro statically polyester powder coated of thickness 60 microns (minimum), including factory

painted after bending.

78 12.52.2 GI Metal Ceiling Lay in perforated Tegular edge global white color tiles of size 595x595 mm and 0.5 Sq.m 2,068.75 1.00 2,068.75

mm thick with 8 mm drop; made of GI sheet having galvanizing of 100 gms/sqm (both sides inclusive)

and 20% perforation area with 1.8 mm dia holes and having NRC (Noise Reduction Coefficient ) of 0.5,

electro statically polyester powder coated of thickness 60 microns (minimum), including factory

painted after bending and perforation, and backed with a black Glass fiber acoustical fleece

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

79 12.53 Providing and Fixing 15 mm thick densified tegular edged eco friendly light weight calcium silicate false Sq.m 2,158.15 1.00 2,158.15

ceiling tiles of approved texture of size 595 x 595 mm in true horizontal level, suspended on inter

locking metal grid of hot dipped galvanised steel sections (galvanising @ 120 grams per sqm including

both side) consisting of main ‘T’ runner suitably spaced at joints to get required length and of size

24x38 mm made from 0.33 mm thick (minimum) sheet, spaced 1200 mm centre to centre, and cross

“T” of size 24x28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between main’T’

at 600 mm centre to centre to form a grid of 1200x600 mm and secondary cross ‘T’ of length 600 mm

and size 24 x28 mm made of 0.33 mm thick (Minimum) sheet to be inter locked at middle of the 1200x

600 mm panel to from grid of size 600x600 mm, resting on periphery walls /partitions on a Perimeter

wall angle pre-coated steel of size(24x24X3000 mm made of 0.40 mm thick (minimum) sheet with the

help of rawl plugs at 450 mm centre to centre with 25 mm long dry wall screws @ 230 mm interval and

laying 15 mm thick densified edges calicum silicate ceiling tiles of approved texture in the grid,

including, cutting/ making opening for services like diffusers, grills, light fittings, fixtures, smoke

detectors etc., wherever required. Main ‘T’ runners to be suspended from ceiling using G.I. slotted

cleats of size 25x35x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm

G.I. adjustable rods with galvanised steel level clips of size 85 x 30 x 0.8 mm, spaced at 1200 mm centre

to centre along main ‘T’, bottom exposed with 24 mm of all Tsections shall be pre-painted with polyster

baked paint, for all heights, as per specifications, drawings and as directed by Engineer-in-Charge.

Note :- Only calcium silicate false ceiling area will be measured from wall to wall. No deduction shall be -

made for exposed frames/opening (cut outs) having area less than 0.30 sqm.The calcium silicate ceiling

tile shall have NRC value of 0.50 (Minimum), light reflection > 85%, non- combustible as per B.S. 476

part IV, 100% humidity resistance and also having thermal conductivity <0.043 w/mK.

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

12.59 Providing & fixing false ceiling at all height including providing & fixing of framework made of special -

section, power pressed from M.S. sheets and galvanised with zinc coating of 120 gms/ sqm (both side

inclusive) as per IS : 277 and consisting of angle cleat of size 25mm wide x 1.6mm thick with flanges of

27mm and 37mm, at 1200mm c/c, one flange fixed to the ceiling with dash fastener 12.5mm dia x

50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25 x10 x0.50mm of

required length with nuts & bolts of required size and other end of angle hanger fixed with

intermediate G.I chanels 45 x15 x 0.90mm running at the spacing of 1200 mm c/c, to which the ceiling

section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26 mm each having lips of

10.5mm, at 450mm c/c, shall be fixed in a direction perpendicular to G.I intermediate channel with

connecting clip made out of 2.64mm dia x 230mm long G.I wire at every junction, including fixing

perimeter channels 0.50mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter

of ceiling fixed to wall/ partitions with the help of Rawl plugs at 450mm centre, with 25mm long dry

wall screws @ 230mm interval, including fixing of Calcium Silicate Board to ceiling section and

perimeter channels with the help of dry wall screws of size 3.5 x25mm at 230mm c/c, including jointing

& finishing to a flush finish of tapered and square edges of the board with recommended jointing

compounds, jointing tapes,finishing with jointing compounds in three layers covering up to 150mm on

both sides of joints and two coats of primer suitable for boards, all as per manufacture's specification

and also including the cost of making opening for light fittings, grills, diffusers, cut outs made with

frame of perimeter channels suitably fixed, all complete as per drawings, specificaton and direction of

the Engineer in charge but excluding the cost of painting with:

80 12.59.1 8 mm thick Calcium Silicate Board made with Calcareous & Siliceous materials reinforced with Sq.m 1,572.30 48.00 75,470.40

cellulose fiber manufactured through autoclaving process.

26.26 Providing & fixing false ceiling at all heights with GRG (Glass Fibre Reinforced Gypsum) false ceiling -

tiles of Size 595x595 mm of approved texture, design and patterns having moisture content less than

2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987, Non combustible as per BS 476

(part 4)-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on

inter-locking metal T-Grid of hot dipped galvanised iron section of 0.33mm thick (galvanized @ 120

grams per sqm including both sides) comprising of main-T runners of size 15x32 mm of length 3000

mm, cross - T of size 15x32 mm of length 1200 mm and secondary intermediate cross-T of size 15x32

mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using

galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-

6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster

of size 85x25x2 mm. Galvanised iron perimeter wall angle of size 24x24x0.40 mm of length 3000 mm to

be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and

40 mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as

per directions of the Engineer-in-Charge.

81 26.26.1 With semi perforated 12 mm thick micro tegular edged GRG false ceiling tiles. Sq.m 1,852.05 963.00 17,83,524.15

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

26.27 Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595mm of approved

texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance ≥

85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true

horizontal level suspended on interlocking T-Grid of hot dipped all round galvanized iron section of

0.33 mm thick (galvanized @120 gsm) comprising of main T runners of 15x32 mm of length 3000 mm,

cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of

length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild

steel item (galvanised@80gsm) 50 mm long 8mm outer diameter M-6 dash fasteners, 6 mm diameter

fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm, spaced

at 1200 mm centre to centre along main ‘T’. The system should rest on periphery walls /partitions with

the help of GI perimeter wall angle of size24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to

the wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws.

The exposed bottom portion of all T-sections used in false ceiling support system shall be pre-painted

with polyester baked paint, for all heights. The work shall be carried out as per specifications, drawings

and as per directions of the engineer-in-charge.

82 26.27.2 With 20 mm thick beveled tegular mineral fibre false ceiling tile (NRC 0.7) Sq.m 2,671.20 20.00 53,424.00

83 PWD SSR ACOUSTICAL WOODWOOL FALSE CEILING: Providing & fixing of 100% Natural Material- Magnesite Sq.m 9,464.19 5.00 47,320.97

2022-23 (Hygroscopic & biologically sound binding agent) bonded woodwool Heradesign planks of

53.33 600Mm*1200Mm *25Mm thickness made out of wood wool fiber of width 1Mm Fiber thickness mixed

with Natural water & Magnesite (No-Cement) with open & smooth surface texture, Weight of panel to

be 11.3 Kg/m2. A Completely harmless Environment & Human Friendly & also a disposable or

recyclable Material & can last for more than 80 Years in building interiors As it has long lifespan &

suitable for Indoor conditions with relative air humidity of upto 90%. Magnesite protects the wood cells

against ageing & fungal attack. To achieve upto NRC=1.00 it should be a clear gap of 200Mm from wall

slab along with the backing of Mineral wool of 50mm thick with 64 kg/m3 density. Ecologically Sound

Material with high mechanical strength with Crash test of 90Km/H with Ball Impact Test DIN18032 &

EN13964 with flying colors & A sustainable material (PEFC & FSC Certified) along with EPD Certified Acc.

to EN ISO 14025 (AUB-Environmental Product declaration). Manufacturing tolerance for nominal size:

Length, Width & Thickness ± 1 mm, & In a Standard Climate of 23° C and 50% rel. humidity.

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

FIXING & SUBSTRUCTURE: Impact Resistant According to DIN-18023 or EN13964 to be Fixed on CD -

Sections Profile framework with Screw 9Pc/Panel & Centre Distance Support of 300Mm & Centre

distance of Cross Profile would be at 600Mm & Main Profile at 900Mm CD Profile is made out of GI(

Sections Profile 60/27/0.6Mm-0.6MmThick x 60Mm Width x 0.27Mm height). The Main Profile is in the

length of 3000mm & to form a section of 600mm x 1200mm. The CD Profile is to be suspended from

soffit with the help of nonius hanger at a center distance of 900mm. UD Profile 28/27/0.6mm to be

fixed on wall at the perimeter of the wall. If the main CD profile needs to extended, it needs to be

connected with CD profile connector 60/27. The CD profiles to be connected to each other at the

intersection by CD cross connector. Heradesign Superfine panels to be fixed to the ceiling with a

minimum of 200mm void or gap with Galvanized screws of length 50Mm & Dia 4.5Mm with a backing

of Mineral Wool of density 64kg/m3 density (50mm thick). Colour pf Panels : NATURAL BEIGE, Can be

Painted to the desired colour (Any- RAL, NCS or StoColor Shades) using water based color by Spray

method prior to installation. FIRE CLASS as per EN 13501-1:B –s1, d0. Test Certificates to be submitted.

84 NS- 32 Providing, supplying and fixing decorative uPVC Soffit Ceiling Panels having tongue and groove Sq.m 4,694.70 934.00 43,84,849.80

interlocking edges, manufactured from premium grade rigid uPVC compound with approved wood

grain/plain finish, waterproof, termite proof, fungus resistant, UV resistant, fire-retardant, impact

resistant and dimensionally stable, having minimum tensile strength of 37 MPa and tensile modulus of

2000 MPa, fixed over approved GI/aluminium supporting framework using manufacturer's

recommended clips, screws and accessories, including all edge trims, mouldings, corner profiles,

closures, cutting, openings for services, scaffolding, labour, transportation and all incidental works

complete as per approved drawings and manufacturer's specifications

85 NS- 33 Providing and fixing horizontal level suspended ceiling comprising of Vertical Linear Baffle Ceiling Sq.m 10,100.70 105.00 10,60,573.50

made out of extruded aluminium in aluminium alloy grade 6063-T5, with baffle blades of size 100/150

x 25 x 3600 mm (nominal), powder coated to approved Woodgrain/Plain finish such as Red Oak,

Cherry, Black/White, with electrostatically applied polyester powder coating of 60–80 micron

thickness. The powder coating shall comply with the specified performance requirements including Salt

Spray Test for 750 hours as per ASTM B117, QUV-A Test for 1000 hours as per ASTM G-154 Cycle-1,

Humidity Test for 1000 hours as per DIN 50017, adhesion GT0 as per EN ISO 2409, shade variation

within manufacturing batch of Delta E<1 and gloss level of 25±5% at 60° as per ASTM D523, where

applicable. The baffle blades shall be suspended using slotted U-profile of 20 x 30 x 3700 mm, 1.5 mm

thick, having slots at 25 mm module to maintain the required on-centre spacing of baffles, with longer

lengths connected using baffle joiners and ends finished with end caps. The suspension system shall

comprise powder-coated mild steel U-profiles of 20(W) x 30(H) x 3750(L) mm, rolled from 1.5 mm thick

MS sheet and having alternate square and rectangular slots of 6.5 x 6.5 mm and 28 x 6.5 mm

respectively for fixing baffle hangers using plugin clips, including U-profile splices, baffle hangers, plugin

clips, U-profile hangers and threaded rods for suspension from the true ceiling. The complete system

shall include all necessary proprietary suspension components, fixing accessories, levelling, alignment,

cutting, jointing, end finishing, labour, tools, tackles and incidental materials, complete in all respects

as per approved manufacturer's specifications, drawings and directions of the Engineer-in-

Charge/Architec

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

86 NS- 34 Stretch fabric ceiling : Providing & Fixing Classic white translucent back light non flammable stretch Sq.m 17,071.65 10.00 1,70,716.50

ceiling with thickness of 0.15 to 0.20 mm. Custom made stretch false ceiling to fit exact dimensions

with aluminum supports.Translucent stretch ceiling composed of calendared PVC [Polyvinyl Chloride

based guaranteed cadium free] membrane with harpoon & corners ready to install. Membrane to

transmit 77% of incident backlight light & absorb 23%. CE certified. Weight of membrane to be 230 gms

/ m2 approx. Panel to be with 10 years warranty on membrane, seam ruptures, discoloration, sag &

profile.Heavy metal and toxic components free.Fire rating: EUROCLASS = B-s1,d0. Humidity resistance.

100% recyclable with USGBC Member Certificate ISO 9001:2015 Certified. To be completed with

wooden / metal base work and LED Lighting.

87 NS- 35 Providing, supplying, and installing acoustic cloud ceiling panels of size 1200 × 1200 × 40 mm with Sq.m 14,226.35 20.00 2,84,527.00

factory-painted straight-cut edges, suspended from the structural soffit using a complete GI suspension

framing system (or as per the approved design and shop drawings), including all suspension

components, hangers, connectors, anchors, fasteners, fixing accessories, and hardware required for a

complete installation. The system shall provide design flexibility for creating multiple layers and angles

and shall be suitable for open ceiling applications where maintaining room volume or installing a full

ceiling is not feasible. The acoustic panels shall achieve a Sound Absorption (Sabine) value of 2.65 at

1000 mm ODS tested as per EN ISO 354, with Flexural Tensile Strength Class C/5N, Fire Classification A2-

s1,d0 as per EN 13501-1 and tested as non-combustible in accordance with EN ISO 1182, Humidity

Resistance Class C suitable for 95% RH at 30°C as per EN 13964:2014, and a minimum Light Reflectance

of 85%. The product shall comply with French VOC Regulation (A+), RTS M1, Eurofins Indoor Air

Comfort®, and IGBC GreenPro certifications, be manufactured in an ISO 14001 certified facility, and

possess an Environmental Product Declaration (EPD) conforming to ISO 14025 and EN 15804, along

with HPD certification. The panels shall contain a minimum of 57% post-consumer recycled content, be

fully recyclable, demountable for maintenance, and suitable for routine dusting, vacuum cleaning, and

wet wiping. The item shall include preparation of shop drawings, coordination with other trades,

cutting and finishing around services, all labour, materials, wastage, lifting, scaffolding, testing, and all

incidental works necessary to complete the installation as per the approved drawings, manufacturer's

specifications, and the Architect's directions, complete in all respects

88 NS- 36 Providing and fixing Veneer False Ceiling consisting of 4mm thick natural wood veneer pressed on Sq.m 10,243.00 10.00 1,02,430.00

12mm thick BWP grade plywood, factory bonded with approved adhesive. The plywood panels shall be

fixed to a concealed framework made of galvanized iron (GI) channels and perimeter sections,

suspended from the RCC slab/structural members using GI suspension rods, cleats, dash fasteners and

necessary hardware. The framework shall ensure a rigid, levelled and true ceiling surface.The veneer

surface shall be finished in site with sanding, wood filler and three coats of polyurethane (PU) clear

finish with inter-coat rubbing to achieve a uniform smooth finish. All cut edges shall be sealed. Panels

shall be installed with proper grain direction, alignment and tight joints as per approved drawings

(Veneer basic rate - 300 Rs/Sq.ft)

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

89 NS- 37 Providing and fixing decorative seasoned 2nd class Indian Teak Wood mouldings, beadings, cornices, Cu.m 2,84,527.30 - -

edge trims and veneer matching mouldings of approved design, profile and size, machine cut and

accurately shaped, fixed with concealed screws, approved adhesive and necessary hardwood

cleats/supports wherever required, including all cutting, shaping, rebating, grooving, mitred joints,

sanding, filling, making good adjoining surfaces, complete with three or more coats of approved

melamine polish over one coat of wood filler/sealer to achieve a uniform finish, including all materials,

labour, scaffolding, tools & tackles, wastage and all incidental works, complete as per approved

drawings and directions of the Engineer-in-Charge.

90 NS- 38 Fire Resistant Glazed Slimline Fixed Partition (120 Minutes – EW 120) Sq.m 99,584.55 5.00 4,97,922.75

Providing, supplying and installing tested slimline fully glazed fire-rated fixed partition system with 120

minutes Integrity and Radiation Control (EW 120), providing symmetrical (bi-directional) fire

protection, complete with factory-fabricated cold rolled galvanized steel profiles of minimum 1.5 mm

thickness, tested as per EN 1364-1:2015 for non-load bearing partitions by an internationally accredited

The glazing shall comprise 14 mm thick clear, fire-rated, non-wired, toughened interlayered glass

providing 120 minutes Integrity (E) and Radiation Control (EW 120), with U-value of 5.02 W/m²K,

minimum 86% light transmission, 38 dB sound reduction, and complying with Class 1(B)1 Impact

Resistance as per EN 12600. The glass shall be tested for UV stability in accordance with EN 12543-4,

provide bi-directional fire protection, and possess a valid Environmental Product Declaration (EPD) in

accordance with EN 15804 and ISO 14025, including recycled content declaration.

The partition frame shall be fabricated from 1.5 mm thick cold rolled galvanized steel profiles forming

50 mm × 80 mm sections with 15 mm flange, with 38 mm face width mullion sections. The frame shall

be fixed to the supporting structure using M10 or larger anchor fasteners at 150 mm from edges and

approximately 500 mm c/c thereafter, or as per approved test evidence.

The glazing shall be secured with minimum 1.25 mm thick steel glazing beads, approved fire-rated -

glazing tape/gasket, and 3 mm thick non-combustible calcium silicate setting blocks, complete with

stainless steel self-tapping studs, sealants, fasteners and all necessary accessories.

The complete partition system shall be tested and certified for fire resistance in accordance with EN

1364-1:2015 by an internationally accredited laboratory. Test reports and certificates shall be duly

signed by the authorized laboratory representative and supported by a certificate of compliance issued

by an authorized certification body. Installation shall be carried out by a manufacturer-approved

certified installer, and the installed system shall be inspected for compliance by the manufacturer or its

authorized representative. The item shall include all materials, fabrication, transportation, installation,

alignment, sealing, testing, certification, finishing and making good complete as per approved

drawings, manufacturer's specifications and the directions of the Engineer-in-Charge.

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

91 NS- 39 GD1-4000 mmX2400 mm -Providing, supplying, installing, testing and commissioning (SITC) of heavy- Sq.m 1,06,697.75 10.00 10,66,977.50

duty automatic bi-parting sliding glass door system comprising a microprocessor-controlled automatic

sliding door operator with high-performance DC motor, integrated encoder and gearbox, extruded

aluminium operator housing, carrier assemblies, trigger belt, digital position selector, obstacle

detection system, safety sensors, microwave/radar activation sensor, electro-mechanical lock,

proximity sensor, keypad, manual lock, floor guides and all necessary accessories. The system shall be

designed for a minimum service life of 1.5 million operating cycles, comply with DIN 18650 and EN

16005 standards, and be suitable for 2 Nos. aluminium framed sliding glass panels and 2 Nos.

aluminium framed fixed glass panels with 26 mm aluminium profiles designed to accommodate 12.5

mm thick laminated safety glass complete with interlocking seals. The operator shall be suitable for

170–260 V AC, 50/60 Hz power supply and capable of carrying 120 kg per sliding panel, providing a

clear opening of 1800 mm (W) × 2200 mm (H). The controller shall provide adjustable opening and

closing speeds, hold-open time, half-opening mode, obstacle detection with automatic reversal, digital

diagnostics, software upgradability, interlocking functionality, and compatibility with fire alarm, access

control and Building Management System (BMS) through RS-485 communication. The work shall

include all fixing accessories, wiring, testing, commissioning, programming, integration with allied

services, demonstration, and handing over, complete in all respects as per approved drawings,

manufacturer's specifications and directions of the Engineer-in-Charge

92 NS- 40 FGD2 & FRD4 -Supply and installation of tested fully glazed fire rated system with 120 minutes of Sq.m 1,02,429.85 48.96 50,14,965.46

integrity and radiation control (EW 120) with symmetrical (bi-directional) fire protection through a VDS

Certified Installer. The frames shall be made with cold rolled profiles. The frames shall be

manufactured from cold rolled 1.5 mm thick steel sheet on all sides. The system shall be tested as per

EN 1634-1:2014 in an international accredited laboratory

The glass should be Contraflam Lite 14 mm clear 120 min fire rated for Integrity, Radiation control -

(EW 120) and partial insulation (EI 20), Non Wired Toughened Interlayered glass with a light

transmission of 86 %, U –value of 5.0 W/sq.mt K, solar factor of 0.72, energy transmission 66 % and a

sound reduction of 38 (-1, -2) dB and manufactured in UL & TUV audited Facility and including UL-EU

Certification (File number R38101) and compliant to class 1(B)1 category of Impact Resistance as per EN

12600. The glass shall be tested and certified for no formation of bubbles or yellowing after 5000 hours

of exposure to UV radiation by TUV Rheinland as per EN 12543-4. The glass shall provide bi-directional

(Symmetrical) fire protection. The glass shall have an Environmental Product Declaration in accordance

with EN 15804 and ISO 14025 in which it’s life cycle analysis is performed considering Cradle to Gate

system boundaries. The glass must produce a recycled content declaration committing to a pre-

consumer cullet of upto 11% and post-consumer cullet upto less than 1%.

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

The Door frames shall be cold rolled profiles . The door frames shall be manufactured from cold rolled

1.5 mm thick steel sheet to form a profile box section of 50 mm x 50 mm on all sides with flange of

20mm. The profile has to be fixed to the supporting construction by means of M10 or bigger anchor

fasteners at every 150 mm from the edges and every 500 mm (approx.) c/c. The overall door opening

shall be as per test evidence and tested as per EN 1634-1 in an accredited international laboratory. The

shutters frames shall be manufactured from cold rolled 1.5 mm thick steel sheet to form a profile box

section of 50 mm x 50 mm on all sides with flange of 20mm and should be fixed to the frame using

weld-on hinges of dimensions 180mm X 20mm. The profiles shall have grooves to incorporate fire-

resistant gaskets. The doors shall incorporate drop down seal at the bottom if required. The glass shall

be held in its place with the help of beading which shall be manufactured from cold rolled 1.25 mm

thick steel sheet and SG Pyrofix lite glazing tape as per the test evidence. The beading shall be clipped

on using steel self-tapping studs fixed at 70 mm from the edges and 300 mm c/c henceforth. The glass

panes are to be supported on non-combustible 5 mm thick calcium silicate setting blocks. The shutter

should be fitted with door closer and SG Dead lock make. Door Shutter shall have SG offset pull

handles. The door should be opening away from the furnace during fire test and same should be

captured in the test report. The frame system shall be manufactured in Intertek audited facility.

The doors shall offer C4 level of wind resistance when tested as per EN12210 and shall provide class 4

level of air permeability as per EN 12207. The door shall also be subjected to durability tests as per EN

12400 for C5 classification.

Test evidence: The test report will be considered valid only if it contains the stamp and signature of the

authorized signatory from Test lab engineer. Test certificate shall also be certificate of compliance from

the authorized certification body.

93 NS- 41 GD3 & GD4-Providing and fixing fully glazed aluminium framed door comprising 50 × 50 × 2 mm thick Sq.m 15,649.00 7.92 1,23,940.08

aluminium box section frame of approved make and finish, fabricated, welded/mechanically joined,

reinforced wherever required, and securely fixed in position with approved fasteners, anchor bolts,

cleats and accessories. The door shutter shall consist of 12 mm thick clear toughened safety glass

conforming to ASTM C-1048, fixed within the aluminium frame using approved EPDM gaskets, glazing

beads, setting blocks and weather-resistant silicone sealant, complete with machine-polished edges

The item shall include supply and fixing of SS 304 grade heavy-duty patch fittings/connecting brackets

wherever required, floor spring of approved make, pivot set, hydraulic door closer (where specified),

mortise lock/patch lock with euro cylinder, SS 304 satin-finish D-type pull handles of suitable length on

both sides, hinges/pivots, door stoppers, all necessary operating hardware, stainless steel screws,

chemical anchors, sealants, packers and all accessories required for smooth and complete operation.

The work shall include all cutting, fabrication, assembly, installation, alignment, adjustments, testing,

making all joints watertight, cleaning of glass and aluminium surfaces, protection until handing over,

and completion in all respects as per approved drawings and directions of the Engineer-in-

Charge/Architect.

Metal Fire rated doors -120minutes -

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

Providing and fixing ISI marked fire rated GI Sheet doors conforming to FD 120-UD classification of IS -

3614 :2021 with fire rating of 120 minutes integrity only. The factory manufactured door frame and

shutter assembly shall be made out of minimum 1.50 mm thick GI Sheet with minimum 120 g/m2

coating as per IS: 277.

The Door should be finished with powder coating in standard RAL shade finish having DFT of minimum

50 microns. The door should carry a minimum 500 Hrs of salt spray test. All accressesories like

hardware, vision panel, fire & smoke seal etc to be supplied by Fire door manufacturer only as per the

guidelines laid down in IS 3614:2021.

Every door must be ISI labeled confirming to type of door & its fire rating.

The offered door must carry a prior valid test evidence of 5 years from CBRI-Roorkee. No fresh testing is

required within the validity of test report from CBRI Roorkee.

The Door frame shall be single rebate grooved profile to accomodate 10x4mm Fire Seal, Size of Frame -

to be minimum 125mm x 55mm made out of minimum 1.50mm thick galvanized steel sheet. Frames

shall be butt / mitered joint and field assembeled with bolting system. The frame should also be

provided with fire rated smoke seal as per IS: 3614:2021 or as per test evidence. It shall be pasted on

surface and perimeter of main frame. All provisions should be mortised & provided with necessary

inbuilt reinforcement to receieve appropriate hardware. Frames should be provided with back plate

bracket for anchor fastner with 8-10 mm dia and minimum 80 mm long HDG fasteners, with Polyamide

sleeves for installation of frame in finished plastered masonary wall opening.

Door leaf should be minimum 60mm thick fully flush double skin door. Door leaf must be -

manufactured from 1.2mm(18gauge) thick galvanised steel sheet. The infill material shall be

honeycomb craft paper insulation. All doors shall be factory prepped for receiving appropriate

hardware and provided with necessary reinforcement for hinges, locks, and door closers. The edges

should be interlocked with a bending radius of 1.4mm. For double leaf doors integrated astragals has to

be provided on the meeting stile for both active and inactive leaf.The shutters shall be mounted to the

frame with SS 304 grade ball bearing type hinges of size 100x89x3 mm alongwith all suitable hardware

Vision lite glass size 300mm x 400mm (max area upto 0.12sqm) wherever applicable should be -

provided with single layered clear fire rated glass panes as per guidelines laid down under IS 3614 :

2021 vide clause no. 7.2.7 table no. 2 with a clipon arrangement. The glass will be provided with fire

rated ceramic tape of suitable size alround on either face. Every Glass pane must carry a permanent

marking. Door must be tested with vision panel- 6mm thick pyroswiss glass.

(Rate including Frame +Shutter +installation+transportation) -

94 NS- 42 FSHD1 - LV/ Ele Shafts - 600x2400 -four side frame Sq.m 19,916.90 7.20 1,43,401.68

Supply & fixing of SS 304 grade Ball Bearing Hinges of size 100 x 89 x 3mm complete with SS Screws of ( -

4 Nos per panel )

Anchor fastners of M10X80mm length. -10 No's -

Supply & fixing of Mortise Dead Lock with 70mm long Euro Profile Cylinder 70mm Long with Both Side -

key Operation -1 Nos

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

Supply and fixing of minimum 6mm thick clear fire rated Glass EQ 120 minutes non Wired of size 200 -

mm x 300mm (Clear vision panel) -01 No's

Supply and Fixing of intumescent fire seal of size 10x4mm -

Supply and Fixing of EPDM Smoke seal -

Concealed Flush Handle OVAL SS 304 Grade 150 mm -1 Nos -

Wooden door NFRD -

Providing & fixing of wooden flush door perfectly seasoned & chemically treated wood. All Flush doors -

are solid core construction bonded with pine wood, confirming to IS-2202 Part-1:99. Duly Factory

pressed and structurally & dimensionally stable. All our doors are pine wood core confirm all IS

The door frame is be made out of any hard wood of section 100 x 50mm with minimum Density of 550- -

650 Kg/m3, with desired painting/polishing finishing as per approved sample, and the rebate is of

15mm x 38mm in the Door Frame to accommodate the shutter.

Door leaf shall be 35 mm thick (23+10+2=35mm) flush door lipping, comprising of 23mm internal core -

100% pine wood cladded with 5mm thick play on both side & 1.5 mm thick Laminate sheet pasted on

both face of the Shutter (As per approved make & shade). Shutter Edges are finish matching to the

door finishing and as per approved sample.

(Rate including Frame +Shutter +installation+transportation) -

Hardware Description -

Supply & fixing of SS 304 grade Ball Bearing Hinges of size 100 x 75 x 3mm complete with SS Screws -

Supply & fixing of anchor fastners M10X120mm length. -

Mortice Sash Lock -complete Set with 70mm BSK Operation & Lever Handle -

Tower bolt 200 mm -

21.3 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with

EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of

engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

96 21.3.2 With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) Sq.m 1,505.25 0.68 1,016.04

9.24 Extra for providing vision panel not exceeding 0.1 sqm in all type of flush doors (cost of glass excluded)

(overall area of door shutter to be measured):

97 9.24.1 Rectangular or square Sq.m 199.15 12.00 2,389.80

Wooden fire rated door -120 min- -

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

Providing and fixing Fully Insulated Non Metallic Wooden doors as per IS 3614:2021, for 120 min -

integrity & 120 min insulation. The door is made out of thoroughly seasoned hard wood. The moisture

content of any material used in the construction of wooden composite fire door sets comprises of both

frame and shutter shall not be more than 15% approx. in accordance with IS 287. The fire door must

have earlier test evidence as per IS/ISO 3008-1. It must have successfully tested from CBRI , Roorkee /

IPIRTI / NABL accrediated lab which operates in accordance with ISO/IEC 17025 for for its fire rating.

Door and frame shall be finished with fire retardent primer FR880.All accressesories like hardware, fire

seal etc to be supplied by Fire door manufacturer only as per the guidelines laid down in IS

3614:2021.Every door must carry a label confirming to type of door & its fire rating.

Door frame shall be Single rebate profile of section 120 x 60 mm made out of Hard wood having -

density should not less than of 550-600 kg/m3 approx. with factory made groove of suitable size so as

to accomodate intumuscent Fire seal of size 20x4mm . An EPDM seal also to be provided in the frame

to check spread of smoke. The frame must be primed with Fire retardant primer FR880 . The frame to

be fixed to fire exit opening with minimum 10 nos. 10 mm dia and minimum 120 mm long HDG (hot dip

galavanized) headed screws with polyamide sleeves.

Wooden shutter with liping should not less than 52mm of thickness finished with commercial ply on -

both faces. If required, the Commercial ply may be replaced with teak ply or may be pasted with 1.5

mm thick Laminate on both faces in desired regular SF grade (any upgradated finish will be payable

extra). The composite thickness of the core insulation will be 37mm consists of minimum 10mm thick

Calcium Silicate boards of Hilux / Pamtech make and treated wool Insulation material . The calcium

silicate board must have Density not more than 900kg/m3 , having thermal conductivity 0.15W/mK .

The shutter should be provided with heat activated intumescent fire seal strip of size 20mm x 4 mm

mounted in the suitable grooves all three sides except bottom provided on Exposed OR concealed

wooden lipping .The shutters shall be mounted to the frame with SS 304 grade ball bearing type hinges

alongwith all suitable hardware

(Rate including Frame +Shutter +installation+transportation) -

Hardware Description -

Supply & fixing of SS 304 grade Ball Bearing Hinges of size 100 x 75 x 3mm complete with SS Screws -

Supply & fixing of anchor fastners of M10X120mm length. -

Supply and Fixing of intumescent fire seal of size 10x4mm -

Supply and Fixing of EPDM Smoke seal -

Supply & fixing of DOOR CLOSER WITH SLIDING ARM -

Supply & fixing of Mortise Dead Lock with 70mm long Euro Profile Cylinder with one Side key other side -

thumb operation

Supply & fixing of SS 304 grade D Type SS Pull Handle B2B of size 300mm mm Long. -

Wooden door NFRD -

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

Providing & fixing of wooden flush door perfectly seasoned & chemically treated wood. All Flush doors -

are solid core construction bonded with pine wood, confirming to IS-2202 Part-1:99. Duly Factory

pressed and structurally & dimensionally stable. All our doors are pine wood core confirm all IS

Door leaf shall be 35 mm thick (23+10+2=35mm) flush door lipping, comprising of 23mm internal core -

100% pine wood cladded with 5mm thick play on both side & 1.5 mm thick Laminate sheet pasted on

both face of the Shutter (As per approved make & shade). Shutter Edges are finish matching to the

door finishing and as per approved sample.

(Rate including Frame +Shutter +installation+transportation) -

Supply & fixing of SS 304 grade Ball Bearing Hinges of size 100 x 75 x 3mm complete -

Supply & fixing of Mortise Dead Lock 70mm long Euro Profile Cylinder withlever handle both the side -

Supply & fixing of SS 304 grade D Type SS Pull Handle B2B of size 300mm mm Long -

Louver grill-450x150mm -

Supply & fixing of SS 304 grade Ball Bearing Hinges of size 100 x 75 x 3mm complete -

Supply & fixing of Mortise Dead Lock 70mm long Euro Profile Cylinder withlever handle both the side -

Supply & fixing of SS 304 grade D Type SS Pull Handle B2B of size 300mm mm Long -

Louver grill-450x150mm -

SS panic bar- -

Metal Fire rated doors -120 minutes Insulation 30 min - -

Providing and fixing ISI marked partially insulated fire rated GI Sheet doors conforming to FD 120-PI -

classification of IS 3614 :2021 with fire rating of 120 minutes integrity and 30 minutes insulation. The

factory manufactured door frame and shutter assembly shall be made out of minimum 1.50 mm thick

GI Sheet with minimum 120 g/m2 coating as per IS: 277.

The Door should be finished with powder coating in standard RAL shade finish having DFT of minimum

50 microns. The door should carry a minimum 500 Hrs of salt spray test. All accressesories like

hardware, vision panel, fire & smoke seal etc to be supplied by Fire door manufacturer only as per the

guidelines laid down in IS 3614:2021.

Every door must be ISI labeled confirming to type of door & its fire rating.The offered door must carry a

prior valid test evidence of 5 years from CBRI-Roorkee. Required third party test report from CBRI

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

The Door frame shall be single rebate grooved profile to accomodate 10x4mm Fire Seal, Size of Frame -

to be minimum 125mm x 75mm made out of minimum 1.50mm thick galvanized steel sheet. Frames

shall be butt / mitered joint and field assembeled with bolting system. The frame should also be

provided with fire rated smoke seal as per IS: 3614:2021 or as per test evidence. It shall be pasted on

surface and perimeter of main frame. All provisions should be mortised & provided with necessary

inbuilt reinforcement to receieve appropriate hardware. Frames should be provided with back plate

bracket for anchor fastner with 8-10 mm dia and minimum 80 mm long HDG fasteners, with Polyamide

sleeves for installation of frame in finished plastered masonary wall opening.

Door leaf should be minimum 60mm thick fully flush double skin door. Door leaf must be -

manufactured from 1.2mm(18gauge) thick galvanised steel sheet. The infill material shall be mineral

wool of minimum density 96 kg/cum. All doors shall be factory prepped for receiving appropriate

hardware and provided with necessary reinforcement for hinges, locks, and door closers. The edges

should be interlocked with a bending radius of 1.4mm. For double leaf doors integrated astragals has to

be provided on the meeting stile for both active and inactive leaf. The shutters shall be mounted to the

frame with SS 304 grade ball bearing type hinges of size 100x89x3 mm alongwith all suitable hardware.

All doors and frames shall be finished with Powder coating in desired RAL Shades. as per the directions -

of the Engineer & site team.

Rate shall include supply and installation of frame, shutter as a complete assembly, including all -

hardware & glass with tapes.

Application : Staircase -

(Rate including Frame +Shutter +installation+transportation)

102 NS- 47 FRD1 - Staircase Doors - 1200mmX 2100mm- Single Leaf Sq.m 22,762.20 12.60 2,86,803.72

Supply & fixing of SS 304 grade Ball Bearing Hinges of size 100 x 89 x 3mm complete with SS Screws -

Supply & fixing of anchor fastners of M10X80mm length. -

Supply & fixing of DOOR CLOSER EN 2-5 WITH SLIDING ARM -

Supply & fixing of SS PANIC BAR FOR SINGLE LEAF - 500S - Stainless Steel -

Supply & fixing of SS PANIC TRIM Trim 006S - Lever,For Operation From The Other Side Of The Panic -

Supply and Fixing of intumescent fire seal of size 10x4mm -

Supply and Fixing of EPDM Smoke seal -

Supply and fixing of minimum 6mm thick clear fire rated Glass EQ 120 minutes non Wired of size 200 -

mm x 300mm (Clear vision )

Wooden fire rated door -120 min- -

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

Providing and fixing Fully Insulated Non Metallic Wooden doors as per IS 3614:2021, for 120 min -

integrity & 120 min insulation. The door is made out of thoroughly seasoned hard wood. The moisture

content of any material used in the construction of wooden composite fire door sets comprises of both

frame and shutter shall not be more than 15% approx. in accordance with IS 287. The fire door must

have earlier test evidence as per IS/ISO 3008-1. It must have successfully tested from CBRI , Roorkee /

IPIRTI / NABL accrediated lab which operates in accordance with ISO/IEC 17025 for for its fire rating.

Door and frame shall be finished with fire retardent primer FR880.All accressesories like hardware, fire

seal etc to be supplied by Fire door manufacturer only as per the guidelines laid down in IS

3614:2021.Every door must carry a label confirming to type of door & its fire rating.

Door frame shall be Single rebate profile of section 120 x 60 mm made out of Hard wood having -

density should not less than of 550-600 kg/m3 approx. with factory made groove of suitable size so as

to accomodate intumuscent Fire seal of size 20x4mm . An EPDM seal also to be provided in the frame

to check spread of smoke. The frame must be primed with Fire retardant primer FR880 . The frame to

be fixed to fire exit opening with minimum 10 nos. 10 mm dia and minimum 120 mm long HDG (hot dip

galavanized) headed screws with polyamide sleeves.

Wooden shutter with liping should not less than 52mm of thickness finished with commercial ply on -

both faces. If required, the Commercial ply may be replaced with teak ply or may be pasted with 1.5

mm thick Laminate on both faces in desired regular SF grade (any upgradated finish will be payable

extra). The composite thickness of the core insulation will be 37mm consists of minimum 10mm thick

Calcium Silicate boards of Hilux / Pamtech make and treated wool Insulation material . The calcium

silicate board must have Density not more than 900kg/m3 , having thermal conductivity 0.15W/mK .

The shutter should be provided with heat activated intumescent fire seal strip of size 20mm x 4 mm

mounted in the suitable grooves all three sides except bottom provided on Exposed OR concealed

wooden lipping .The shutters shall be mounted to the frame with SS 304 grade ball bearing type hinges

alongwith all suitable hardware

Application : Main door /meter room /fire comtrol room -

(Rate including Frame +Shutter +installation+transportation)

103 NS- 48 FRD2 - Meter /Fire control Room Door - 1000mmX 2400mm-Single Leaf Sq.m 23,473.50 4.80 1,12,672.80

Hardware Description -

Supply & fixing of SS 304 grade Ball Bearing Hinges of size 100 x 75 x 3mm complete with SS Screws -

Supply & fixing of anchor fastners of M10X120mm length. -

Supply and Fixing of intumescent fire seal of size 10x4mm -

Supply and Fixing of EPDM Smoke seal -

Supply & fixing of DOOR CLOSER WITH SLIDING ARM -

Supply & fixing of Mortise Dead Lock with 70mm long Euro Profile Cylinder with one Side key other side -

thumb operation

Supply & fixing of SS 304 grade D Type SS Pull Handle B2B of size 300mm mm Long. -

104 NS- 49 FRD3 - Kitchen/Pantry Entrance Door - 1500mmX 2400mm-Double leaf Sq.m 25,607.45 3.60 92,186.82

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

Supply & fixing of SS 304 grade Ball Bearing Hinges of size 100 x 75 x 3mm complete with SS Screws. -

Supply & fixing of anchor fastners. -

Supply and Fixing of intumescent fire seal of size 10x4mm -

Supply and Fixing of EPDM Smoke seal -

Supply & fixing of DOOR CLOSER WITH SLIDING ARM -

Supply & fixing of Mortise Dead Lock G with 70mm long Euro Profile Cylinder with one Side key other -

side thumb operation

Supply & fixing of SS 304 grade D Type SS Pull Handle B2B of size 300mm mm Long of -

Concealed Flush Bolt -Metal - SS 304G-300mm long on top -

Concealed Flush Bolt -Metal - SS 304G-300mm long on Bottom -

SS304 kick Plate - 450x750 -

Supply and fixing of minimum 6mm thick clear fire rated Glass EQ 120 minutes non Wired of size -

300mm dia (Clear vision )

Wooden fire rated door -120 min- -

Providing and fixing Fully Insulated Non Metallic Wooden doors as per IS 3614:2021, for 120 min -

integrity & 120 min insulation. The door is made out of thoroughly seasoned hard wood. The moisture

content of any material used in the construction of wooden composite fire door sets comprises of both

frame and shutter shall not be more than 15% approx. in accordance with IS 287. The fire door must

have earlier test evidence as per IS/ISO 3008-1. It must have successfully tested from CBRI , Roorkee /

IPIRTI / NABL accrediated lab which operates in accordance with ISO/IEC 17025 for for its fire rating.

Door and frame shall be finished with fire retardent primer FR880.All accressesories like hardware, fire

seal etc to be supplied by Fire door manufacturer only as per the guidelines laid down in IS

3614:2021.Every door must carry a label confirming to type of door & its fire rating.

Door frame shall be Single rebate profile of section 120 x 60 mm made out of Hard wood having -

density should not less than of 550-600 kg/m3 approx. with factory made groove of suitable size so as

to accomodate intumuscent Fire seal of size 20x4mm . An EPDM seal also to be provided in the frame

to check spread of smoke. The frame must be primed with Fire retardant primer FR880 . The frame to

be fixed to fire exit opening with minimum 10 nos. 10 mm dia and minimum 120 mm long HDG (hot dip

galavanized) headed screws with polyamide sleeves.

Wooden shutter with liping should not less than 52mm of thickness finished with commercial ply on -

both faces. If required, the Commercial ply may be replaced with teak ply or may be pasted with 1.5

mm thick Laminate on both faces in desired regular SF grade (any upgradated finish will be payable

extra). The composite thickness of the core insulation will be 37mm consists of minimum 10mm thick

Calcium Silicate boards of Hilux / Pamtech make and treated wool Insulation material . The calcium

silicate board must have Density not more than 900kg/m3 , having thermal conductivity 0.15W/mK .

The shutter should be provided with heat activated intumescent fire seal strip of size 20mm x 4 mm

mounted in the suitable grooves all three sides except bottom provided on Exposed OR concealed

wooden lipping .The shutters shall be mounted to the frame with SS 304 grade ball bearing type hinges

alongwith all suitable hardware

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

Application : Main door /meter room /fire comtrol room -

(Rate including Frame +Shutter +installation+transportation)

Supply & fixing of SS 304 grade Ball Bearing Hinges of size 100 x 75 x 3mm complete with SS Screws. -

Supply & fixing of anchor fastners. -

Supply and Fixing of intumescent fire seal of size 10x4mm -

Supply and Fixing of EPDM Smoke seal -

Supply & fixing of DOOR CLOSER WITH SLIDING ARM -

Supply & fixing of Mortise Dead Lock G with 70mm long Euro Profile Cylinder with one Side key other -

side thumb operation

Supply & fixing of SS 304 grade D Type SS Pull Handle B2B of size 300mm mm Long of -

Concealed Flush Bolt -Metal - SS 304G-300mm long on top -

Concealed Flush Bolt -Metal - SS 304G-300mm long on Bottom -

SS304 kick Plate - 450x750 -

Supply and fixing of minimum 6mm thick clear fire rated Glass EQ 120 minutes non Wired of size -

200mmX300mm (Clear vision )

106 PWD SSR Providing and fixing of factory made uPVC Louver window (White Colour) comprising of uPVC multi- Sq.m 11,438.45 10.00 1,14,384.48

2022-23 chambered with wall thickness of 2.3mm (+-0.2 mm ), duly reinforced with 1.5 mm thick G. I. Section.

54.11 uPVC window & door profile shall be made in India & shall conform to BS EN 12608 and other

standards as mentioned below: S.No. Name of the test Test Method Specifie Parameter

1 Tensile Impact Strength ISO 8256 - more than 700Kj/m2 2 Vicat Softening

Temperature EN ISO – 306 Shall not be < 750C

3 Charpy Impact Strength EN ISO – 179-2 Shall not be < 20KJ/m2

4 Flexural Modulus Elasticity EN ISO – 178 Shall not be < 2200 N/mm2

5 Mean Breaking Stress for welded corner

(a) For the tensile bending test EN – 514 Shall not be < 25 N/mm2

(b) For the compression bending test Shall not be < 30N/mm2

6 Heat Reversion Test IS:4985-2000 Shall not be > 2.0 %

7 Surface Spread of flame BS : 476 - Part 7 Classification 1

8 Ignitability Evaluation BS : 476 - Part 5 'P' Not easily ignitable

9 Tensile modulus ASTM D 638 Shall not be < 35 MPa

10 Shear Modulus ASTM D 732 Shall not be < 220 MPa

11 Tensile Strength EN ISO 527 Shall not be < 30 MPa. All corners of frame shall be fusion welded. Both

vertical sides of the frame, adjustable louver mechanism having one lever or fixed louver bracket shall

be fitted with the of 4 mm Frosted Annealed glass. Window will be fixed to the wall with 100mm long

and 8mm dia. Fasteners and complete in all respect as per direction of Engineer-In-Charge.

uPVC Window and Door Profiles are warranted for a period of ten (10) years against non-uniform

discoloration,wrapping and rotting under general use.

a.Louver Window (Big Series) frame of size 67 x 62 mm & Mullion (if required) of size 67 x 78 mm.

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

PWD SSR Providing and fixing of factory made uPVC casement window / Fixed Window & Casement Door (White

2022-23 Colour) comprising uPVC multi-chambered frame, Sash, & Mullion with wall thickness of 2.3mm (+-0.2

54.09 mm ), duly reinforced with G.I. section 1.5 mm, wherever required. uPVC window & door profile shall

be made in India & shall conform to BS EN 12608 and other standards as mentioned below: S.No. Name

test Test Method Specified Parameter

1 Tensile Impact Strength ISO 8256 - more than 700Kj/m2 2 Vicat

Softening Temperature EN ISO – 306 Shall not be < 750C

3 Charpy Impact Strength EN ISO – 179-2 Shall not be < 20KJ/m2

4 Flexural Modulus Elasticity EN ISO – 178 Shall not be < 2200 N/mm2

5 Mean Breaking Stress for welded corner

(a) For the tensile bending test EN – 514 Shall not be < 25 N/mm2

(b) For the compression bending test Shall not be < 30N/mm2

6 Heat Reversion Test IS:4985-2000 Shall not be > 2.0 %

7 Surface Spread of flame BS : 476 - Part 7 Classification 1

8 Ignitability Evaluation BS : 476 - Part 5 'P' Not easily ignitable

9 Tensile modulus ASTM D 638 Shall not be < 35 MPa

10 Shear Modulus ASTM D 732 Shall not be < 220 MPa

11 Tensile Strength EN ISO 527 Shall not be < 30 MPa. All corners of frame and sash

will be fusion welded. Mullion shall be welded / screwed. EPDM / TPE Gasket shall be

provided in all frame, sash & mullion, wherever necessary.Thereafter, 5 mm Float

Annealed glass shall be provided in the sash with the help of uPVC glazing bead and

hardware, i.e., friction hinge & single point handle (in window) & 3D Hinges &

Multipoint Lock (in door) shall be provided. Window / Door shall be fixed to the wall with

100mm long and 8mm dia. Fasteners and complete in all respect as per direction of

Engineer-In-Charge. uPVC Window and Door Profiles are warranted for a period of ten

107 a (10) years against

Casement Windownon-uniform discoloration,

(Big Series) frame wrapping

of size 67 x 62 mmand rotting

& Sash under general

108 c Fixed Window (Big Series) frame of size 67 x 62 mm & Mullion (if required) of size 67 x 78 mm Sq.m 10,335.74 - -

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

PWD SSR Providing and fixing of factory made uPVC Sliding window & door (White Colour) complete, comprising

2022-23 uPVC multi-chambered frame having in-built uPVC roller track on top and uPVC sash with wall thickness

54.08 of 2.3mm (+-0.2 mm), duly reinforced with G.I. section 1.5 mm, wherever required. uPVC window &

door profile shall be made in India & shall conform to BS EN 12608 and other standards as mentioned

Name of the test Test Method Specified Parameter

1 Tensile Impact Strength ISO 8256 - more than 700Kj/m2 2 Vicat

Softening Temperature EN ISO – 306 Shall not be < 750C

3 Charpy Impact Strength EN ISO – 179-2 Shall not be < 20KJ/m2

4 Flexural Modulus Elasticity EN ISO – 178 Shall not be < 2200 N/mm2

5 Mean Breaking Stress for welded corner

(a) For the tensile bending test EN – 514 Shall not be < 25 N/mm2

(b) For the compression bending test Shall not be < 30N/mm2

6 Heat Reversion Test IS:4985-2000 Shall not be > 2.0 %

7 Surface Spread of flame BS : 476 - Part 7 Classification 1

8 Ignitability Evaluation BS : 476 - Part 5 'P' Not easily ignitable

9 Tensile modulus ASTM D 638 Shall not be < 35 MPa

10 Shear Modulus ASTM D 732 Shall not be < 220 MPa

11 Tensile Strength EN ISO 527 Shall not be < 30 MPa

All corners of frame and sash will be fusion welded. After placing 5 mm Float Annealed glass in the

sash, uPVC glazing bead, interlock, EPDM / TPE gasket, brush shall be provided including touch lock and

rollers & proper drainage system shall be provided.

Window / Door will be fixed to the wall with 100mm long and 8mm dia. Fasteners and complete in all

respect as per direction of Engineer-In-Charge. uPVC Window and Door Profiles are warranted for a

period of ten (10) years against non-uniform discoloration, wrapping and rotting under general use

109 c 3 Track with Mesh-2 Glass Sash + 1 Mesh Sash (Each sash shall be half of width of window) (Big Series) Sq.m 12,092.64 - -

Window frame of size 122 x 54 mm & Sash of size 64 x 47 mm.

110 PWD SSR Supply and installation of cubicles of width and depth as per specifications/ site drawings. Cubicle Sq.m 10,313.44 1.00 10,313.44

2022-23 height will be 1980 mmTitan Std Series Cubicles: Std Sizes (W x D x H): 900 mm x 1550 mm x 1980

51.166 mm/2039 mm ( Height is including 150 mm gap from bottom) Door Size- 600 mm when top rail of

rectangular cross section is used and 2039 mm when top rail of circular cross section is usedITEM

DESCRIPTION Made from solid grade Merino make compact high pressure laminate as per IS:2046 and

EN-438 manufactured under high specific pressure > 5 MPa and temperature >120°C, All doors will be

of single colour and made of 12 mm thick Merino HPL compact panel. All pilasters will be made of 12

mm thick HPL compact panel. Size of panels to be as per drawing. HARDWARE & ACCESSORIES are Top

rail is made of stainless steel grade 304. There are two options for the top rail. First one comes with a

rectangular cross section (Size to be 55mmx42mmx1.6 mmT) and the other one comes with circular

cross section (Diameter 32 mm). Surface finish to be brush type. A thin plastic film pasted for surface

protection. Corner joinery section made from Stainless steel grade 304. Surface finish to be brush type.

A thin plastic film pasted for surface protection. Size to be 35mmx15mmx0.8 mm. etc complete.

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

111 PWD SSR ACOUSTICAL WOODWOOL WALL PANELLING: Providing & fixing of 100% Natural Material- Magnesite Sq.m 8,158.82 5.00 40,794.08

2022-23 (Hygroscopic & biologically sound binding agent) bonded woodwool Heradesign planks of

53.32 600Mm*1200Mm *25Mm thickness made out of wood wool fibre of width 1Mm Fiber thickness mixed

with Natural water & Magnesite (No-Cement) with open & smooth surface texture, Weight of panel to

be 11.3 Kg/m2. A Completly harmless Envirenment & Human Friendly & also a disposable or recyclable

Material & can last for more than 80 Years in building interiors As it has long lifespan & suitable for

Indoor conditions with relative air humidity of upto 90%. Magnesite protects the wood cells against

ageing & fungal attack. To achive upto NRC=1.00 it should be a clear gap of 200Mm from wall slab

along with the backing of Mineral wool of 50mm thick with 64 kg/m3 density. Ecologically Sound

Material with high mechanical strength with Crash test of 90Km/H with Ball Impact Test DIN18032 &

EN13964 with flying colors & A sustainable material (PEFC & FSC Certified) along with EPD Certified Acc.

to EN ISO 14025 (AUB-Envirenmental Product declaration). Manufacturing tolerance for nominal size:

Length, Width & Thickness ± 1 mm, & In a Standard Climate of 23° C and 50% rel. humidity.

FIXING & SUBSTRUCTURE: Impact Resitant According to DIN-18023 or EN13964 to be Fixed on CD -

Sections Profile framework with Screw 9Pc/Panel & Centre Distance Support of 300Mm & Centre

distance of Cross Profile would be at 600Mm & Main Profile at 900Mm CD Profile is made out of GI(

Sections Profile 60/27/0.6Mm-0.6MmThick x 60Mm Width x 0.27Mm height). The Main Profile is in the

legth of 3000Mm & to form a section of 600mm x 1200mm. Heradesign Superfine panels to be fixed on

the wall with a minimum of 200Mm void or gap with Galvanized screws of length 50Mm & Dia 4.5Mm

with a backing of Mineral Wool of density 64kg/m3 density (50mm thick).Colour Of Panels : NATURAL

BEIGE, Can be Painted to the desired colour (Any- RAL, NCS or StoColor Shades) using water based color

by Spray method prior to installation. FIRE CLASS as per EN 13501-1:B –s1, d0. Test Certificates to be

112 NS- 51 Providing and fixing laiminated wall panelling on internal walls, beams and other vertical surfaces Sq.m 7,824.50 788.00 61,65,706.00

using an aluminium framework system comprising 50 mm × 25 mm × 1.5 mm thick hollow aluminium

sections arranged at 600 mm × 600 mm grid spacing, securely fixed to the existing wall/structure with

approved anchors, fasteners and accessories, and aligned true to line, level and plumb.

The aluminium sub-frame shall be provided with 12 mm thick BWP grade plywood (IS:710 grade)

backing, securely fixed using approved screws and fasteners. Over the plywood backing, providing and

fixing 1.5 mm thick laminate of approved make, shade and grain pattern, including application of

suitable adhesive, pressing, edge treatment, joint alignment and seamless finishing to achieve a

premium decorative appearance.

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

113 NS- 52 Providing, supplying and fixing decorative uPVC Fluted Wall Panels of approved profile and design, Sq.m 7,113.20 - -

manufactured from premium grade rigid uPVC, factory finished in approved wood grain, solid colour or

metallic finish, of size 140 mm (W) × 3060 mm (L) with tongue and groove interlocking edges. The

panels shall be fire-retardant, moisture resistant, termite proof, fungus resistant, UV resistant, impact

resistant and dimensionally stable, having minimum tensile strength of 37 MPa, minimum tensile

modulus of 2000 MPa, and no surface distortion at 120°F (approximately 50°C). The panels shall be

fixed over approved aluminium frame work of 600x600 mm grid backing including labour,

transportation and all incidental works, complete in all respects as per approved drawings and

directions of the Engineer-in-Charge

114 NS- 53 Providing & fixing Frost Series Roller Blinds (Custom Printed Series) or as approved. The blinds consist Sq.m 3,556.60 2,440.00 86,78,104.00

a top tube extruded from non-rusting aluminium alloy with a 2.0 mm wall thickness, and available in 40

mm diameter for small and large blinds respectively. The Frost Series fabric have a thickness of 0.48

mm in approved shades and a composition of 100% PES Polyester Acrylic. The fabric weight shall be

200 GSM (±5%) with a light fastness grade of 4, ensuring long-lasting color durability with best quality.

The fabric is securely enclosed in a suitably designed pocket along with the top tube to ensure smooth

rolling operation. The bottom channel is made of non-rusting aluminium, powder-coated, and of 2.0

mm thickness. Both ends of the bottom channel shall be sealed with end caps in matching color to

provide a neat, elegant, and uniform appearance. The mounting brackets is made of powder-coated

steel, offering superior finish and corrosion protection. The bracket design allow's both overhead and

side mounting and is incorporate a clutch assembly at either end of the blind, capable of handling up to

15 kg of load. ( Fabric basic rate : 180 Rs/Sq.ft)

115 NS- 54 Providing, supplying and fixing Z-type (Zebra / Day–Night) roller blinds, made of dual-layer polyester Sq.m 3,000.00 100.00 3,00,000.00

fabric with alternating sheer (transparent) and opaque bands to allow light control and privacy, suitable

for windows, complete with aluminium roller tube, bottom bar, side brackets, clutch mechanism,

chain/cord control, all fixing accessories, alignment and smooth operation, complete as per

manufacturer’s specifications and directions of the Engineer

116 R3-CS-RM- Providing &Fixing frosted film manufactured by 3 M approved equivalent on glass partition wherever Sq.m 1,532.82 56.20 86,138.35

137 required as per the instruction of Architect.

117 R3-CS-FUR- Providing and fixing wall paper / Graphic for highlighting the walls with proper adhesive in line level Sq.m 2,784.80 25.00 69,620.00

28 for reception, conference & Auditorium rooms and wherever required as per the drawings. Basic rate

of Wall paper is Rs..100/- per Sft.

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

118 NS- 55 Providing and fixing veneer wall panelling on internal walls, beams and other vertical surfaces using an Sq.m 9,958.45 - -

aluminium framework system comprising 50 mm × 25 mm × 1.5 mm thick hollow aluminium sections

arranged at 600 mm × 600 mm grid spacing, securely fixed to the existing wall/structure with approved

anchors, fasteners and accessories, and aligned true to line, level and plumb.

The aluminium sub-frame shall be provided with 12 mm thick BWP marine plywood (IS:710 grade)

backing, securely fixed using approved screws and fasteners. Over the plywood backing, providing and

fixing 4 mm thick natural veneer finish of approved make, shade and grain pattern, including

application of suitable adhesive, pressing, edge treatment, veneer matching, joint alignment and

seamless finishing to achieve a premium decorative appearance. The veneer surface shall be finished

with approved clear PU coating as per manufacturer's recommendations, including surface preparation,

sanding and required number of coats to achieve a smooth, durable and uniform finish.. (Veneer basic

rate -300 Rs/Sq.ft)

119 NS- 56 Providing and fixing WPC decorative moulding having projection from 12 mm to 18 mm, Rmt 497.90 10.00 4,979.00

manufactured from premium quality Wood Plastic Composite, complete with cutting, mitred joints,

approved adhesive, SS screws wherever required, finishing, alignment and making good complete as

per approved drawings and direction of the Engineer-in-Charge

120 NS- 57 Providing and fixing WPC decorative moulding having projection from 18 mm to 25 mm, Rmt 640.20 5.00 3,201.00

manufactured from premium quality Wood Plastic Composite, complete with cutting, mitred joints,

approved adhesive, SS screws wherever required, finishing, alignment and making good complete as

per approved drawings and direction of the Engineer-in-Charge

121 NS- 58 Providing and fixing WPC decorative moulding having projection from 25 mm to 50 mm, Rmt 924.70 5.00 4,623.50

manufactured from premium quality Wood Plastic Composite, complete with cutting, mitred joints,

approved adhesive, SS screws wherever required, finishing, alignment and making good complete as

per approved drawings and direction of the Engineer-in-Charge

122 NS- 59 Providing and applying Polyurethane (PU) polish on exposed wooden surfaces, including thorough Sq.m 1,422.65 - -

surface preparation by cleaning, sanding with suitable grades of sandpaper, filling minor imperfections

with approved wood filler where required, application of compatible wood sealer/primer, and finishing

with two or more coats of clear PU polish (matt, satin or gloss finish as approved) to achieve a smooth,

uniform and durable finish. The PU coating shall provide resistance to abrasion, moisture, stains and

chemicals, complete with intermediate sanding between coats wherever required. The rate shall

include all materials, labour, scaffolding (if required), tools and tackles, and all incidental works

necessary to complete the work as directed by the Engineer-in-Charge

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

123 NS- 60 Providing and fixing wall-mounted mirror paneling as per approved architectural drawings and design, Sq.m 7,753.40 10.00 77,534.00

comprising a perfectly plumb base substrate of 12mm thick BWP Grade Plywood mechanically fastened

to the wall, overlaid with an aluminum sheet to act as a definitive moisture and vapor barrier. Over this

prepared backing, supply and install [5mm] thick Extra-Clear (Low-Iron) Mirror with machine-polished

edges, adhered exclusively using premium non-acidic, neutral-cure mirror silicone and double-sided

spacer tapes to prevent desilvering. The comprehensive rate includes all materials, hardware, labor,

leveling, surface preparation, wastage, and final cleaning, with all material samples, edge treatments,

and grid layouts subject to prior mockup and final approval by the Architect

124 NS- 61 Providing, supplying and fixing Acoustic PET Panels manufactured from recycled polyester (PET) fibres, Sq.m 7,682.25 10.00 76,822.50

minimum 12 mm thickness (as specified in the drawings), having minimum 60% recycled content, Class

A sound absorption performance (NRC up to 0.80 or higher depending upon installation), fire-retardant

complying with applicable standards, free from formaldehyde, low VOC, moisture resistant, fungus

resistant and dimensionally stable. Panels shall be factory finished in approved colour, texture and

pattern with square/bevelled edges as per approved design.

The panels shall be fixed over prepared substrate/wall/ceiling framework using approved high-strength

adhesive, concealed mechanical fasteners, aluminium/GI support framework, or proprietary fixing

accessories as recommended by the manufacturer, ensuring proper alignment, joints, edge finishing

and seamless appearance. The work shall include cutting, routing, edge profiling, openings for electrical

fixtures/services, corner trims, mouldings, all accessories, wastage, scaffolding, labour, handling and

complete installation to the satisfaction of the Engineer-in-Charge.

The rate shall include all materials, accessories, transportation, loading, unloading, installation, testing,

cleaning and making good the surrounding surfaces complete in all respects.

125 NS- 62 roviding, supplying and fixing factory-manufactured Acoustic Grooved Slat Panels of size 192 × 2440 × Sq.m 8,251.30 - -

16 mm, manufactured from E1 grade pine wood fibreboard (MDF/HDF) conforming to EN 13986 or

equivalent, with factory-applied melamine finish, tongue & groove edges, precision grooved

perforations (2 mm grooves at 12/24/48/96 mm centres as specified), acoustical fleece backing and 25

mm thick polyester acoustic infill, achieving minimum NRC 0.75 and Class 2 surface spread of flame as

per BS 476 Part 7 or equivalent. The panels shall be fixed on a concealed aluminium framework with all

brackets, clips, fasteners, expansion joints, edge trims, cutting, openings for services, sealants and

accessories, complete in all respects as per approved drawings and manufacturer's specifications.

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

126 NS- 63 Providing, fabricating and fixing 77 mm overall thick full height or low height partition comprising a Sq.m 12,092.40 472.00 57,07,612.80

framework of 50 × 25 × 1.5 mm thick aluminium hollow sections, securely fixed to floor, wall, soffit and

adjoining members with approved cleats, brackets and anchor fasteners. The framework shall be filled

with 50 mm thick acoustic Resimer infill (to be measured and paid separately under the relevant BOQ

item) to improve sound insulation performance. The framework shall be clad on both sides with 12 mm

thick BWP Grade plywood conforming to IS:710 and finished on both exposed faces with 1.0 mm thick

decorative high-pressure laminate of approved make, shade and texture, bonded with approved

adhesive. The partition shall have an overall finished thickness of 77 mm. The item shall include all

intermediate framing members, stiffeners, cleats, brackets, fasteners, screws, adhesives, sealants,

cutting, routing, drilling, edge finishing, matching laminate edge banding, finishing to all exposed

edges, corners, returns, jambs, end closures, aluminium trims/beadings wherever required, making

openings for services, making good, cleaning and all labour, materials, tools and tackles complete in all

respects as per approved drawings and directions of the Engineer-in-Charge

127 NS- 64 Providing and fixing 50 mm thick Acoustic Resimer FR infill within aluminium partition framework, Sq.m 1,351.50 472.00 6,37,908.00

comprising FR Grade honeycomb structured acoustic panels of standard size 1200 × 1200 × 50 mm or

approved customised sizes, having NRC up to 0.90, UL 94 HF-1 Fire Retardant (Self-Extinguishing)

rating, thermal conductivity not exceeding 0.032 W/m·K, 100% recyclable, CFC-free, low VOC, RoHS &

REACH compliant, moisture resistant and resistant to insects, rodents, bacteria and fungi.

The panels shall be cut to required sizes and securely fixed within the framework using approved

adhesive, GI retainers or other manufacturer-recommended fixing system, complete with all cutting,

fitting, wastage, labour, tools and accessories as per manufacturer's specifications and directions of the

Engineer-in-Charge

128 NS- 65 Providing and fixing full height or low height framed glass partition comprising 12 mm thick clear Sq.m 15,649.00 30.00 4,69,470.00

toughened safety glass of approved make, machine cut, polished and edge-finished on all exposed

edges, fixed within 50 × 50 × 2.0 mm thick powder-coated/anodized aluminium box sections (or

equivalent approved section as per manufacturer's design) all around the perimeter, complete with

glazing gaskets, EPDM/rubber beading, setting blocks, pressure plates, approved silicone sealant,

screws, cleats, brackets, anchor fasteners and all necessary accessories. The item shall include cutting,

fabrication, assembly, alignment, fixing, joint treatment, making good, cleaning and all labour,

materials, tools and tackles complete in accordance with the approved drawings and directions of the

Engineer-in-Charge

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

129 NS- 66 Providing and fixing back-painted / lacquered glass wall cladding comprising 6 mm thick toughened Sq.m 6,544.10 10.00 65,441.00

clear glass, having back surface factory coated with approved high-quality opaque lacquer/paint in

approved colour and shade, with uniform colour, smooth and defect-free finish, manufactured and

processed to required sizes and shapes as per approved drawings and site conditions. The glass shall

have polished/smooth arrissed edges and shall be fixed over prepared substrate using approved

neutral-cure structural silicone adhesive and/or suitable mechanical fixing system as recommended by

the glass manufacturer, including required setting blocks, spacers, backing/supporting members,

sealants, joints and accessories. All exposed edges, cut-outs, corners, junctions and openings shall be

neatly finished, with accurate alignment, level, plumb and uniform joints. The work shall include

measurement, shop drawings, templates, cutting, edge polishing, toughening, back

painting/lacquering, transportation, handling, protection, installation, cleaning and all necessary

labour, tools, tackles, consumables and incidental materials, complete in all respects as per approved

sample, manufacturer's recommendations and directions of the Engineer-in-Charge/Architect.

9.48 Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or -

round bars etc. including priming coat with approved steel primer all complete.

130 9.48.2 Fixed to openings /wooden frames with rawl plugs screws etc. Kg 238.35 100.00 23,835.00

131 10.1 Structural steel work in single section, fixed with or without connecting plate, including cutting, Kg 117.35 100.00 11,735.00

hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

132 10.28 Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., Kg 772.40 1,620.00 12,51,288.00

including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the

same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary

accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the

floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for

payment purpose only weight of stainless steel members shall be considered excluding fixing

accessories such as nuts, bolts, fasteners etc.).

133 R3-CS-RM- Providing & Fixing corner guard for columns at parking area size W100 x H800 x 8mm colour: Black No's 965.24 105.00 1,01,350.20

128 with yellow or White Reflective Stickers Body Material: Modified Thermoplastics (Polymer Rubberized)

Fixing: Fixed on the wall & corner of columns with six 2" Screws.

134 NS- 67 Providing, supplying and placing free-standing umbrella rack of standard size Ø300 mm × 600 mm No's 14,226.35 1.00 14,226.35

(Height), fabricated from SS 304 stainless steel of minimum 1.2 mm thickness with satin/matte brushed

finish. The rack shall be of cylindrical perforated design with laser-cut circular/oval perforations for

ventilation and aesthetics, complete with removable stainless steel drip tray for water collection,

reinforced top and bottom rings, non-slip rubber floor protectors, smooth polished edges, and all

necessary accessories. The umbrella rack shall have a minimum storage capacity of 10–12 umbrellas, be

corrosion-resistant, easy to maintain, and suitable for use in entrance lobbies, reception areas, offices,

clubs, hotels and other public buildings, complete in all respects as per the approved design and

directions of the Engineer-in-Charge

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

135 NS- 68 Providing, fabricating, supplying and placing free-standing shoe stand of standard size 900 mm (L) × No's 17,071.65 1.00 17,071.65

350 mm (D) × 900 mm (H), fabricated from MS square hollow sections of 25 × 25 × 1.6 mm and 20 × 20

× 1.6 mm thickness with 1.2 mm thick MS sheet/perforated sheet shelves. The stand shall consist of 4-

tier storage with a capacity of approximately 16–20 pairs of shoes, complete with all welding, grinding,

edge finishing, levelling, rubber/PVC floor protectors, and finished with one coat of zinc-rich metal

primer and two coats of premium grade powder coating of approved colour (minimum 60–80 microns

DFT). The shoe stand shall be sturdy, corrosion-resistant, and complete in all respects as per the

approved design and directions of the Engineer-in-Charge

136 NS- 69 Providing, supplying and fixing decorative photo frame of approved size and design, comprising a rigid Sq.m 5,000.00 25.00 1,25,000.00

MDF/HDHMR board or equivalent substrate with decorative moulded profile/frame made of

PU/polymer/wooden moulding, duly finished with approved colour/finish such as PU paint, duco paint,

melamine or wood finish. Item shall include provision of clear glass/acrylic front cover, high-quality

printed/enlarged photograph/artwork as approved, backing board, required clips/fasteners, wall

mounting hardware, cutting, fabrication, edge finishing and installation complete in all respects, as per

approved design, sample and direction of Engineer-in-Charge

137 NS- 70 Providing, fabricating, supplying and fixing decorative 3D heritage wall relief artwork of approved Sq.m 35,000.00 40.00 14,00,000.00

design, size and pattern, made of FRP moulded panels with required MS/FRP backing support,

incorporating raised figures, motifs and architectural details, finished in approved stone

texture/antique bronze/metallic PU finish, including moulding, surface preparation, painting, concealed

supports, fixing hardware, transportation, lifting, scaffolding, installation, alignment and cleaning

complete in all respects as per approved design and direction of Engineer-in-Charge.

138 NS- 71 Providing, fabricating, supplying and installing decorative heritage statue/bust of approved design and Nos 1,50,000.00 1.00 1,50,000.00

size, made of FRP (Fiber Reinforced Plastic) with internal MS reinforcement, moulded/cast to detailed

artwork, with smooth finished surface and antique bronze/metallic PU finish, mounted on a decorative

pedestal made of approved stone with decorative moulding, with metallic detailing, including

concealed fixing, base plate, anchoring, transportation, lifting, installation, alignment, cleaning and all

necessary materials, labour, tools, tackles and accessories complete as per approved design and

direction of Engineer-in-Charge

139 NS- 72 Providing, fabricating, supplying and fixing decorative sword and shield wall artwork of approved Set 25,000.00 2.00 50,000.00

design and size, comprising metal fabricated sword and shield, with moulded/cast detailing and

antique bronze/gold metallic PU finish, including decorative detailing, concealed MS backing/support,

wall mounting brackets, anchor fasteners, fixing accessories, transportation, installation, alignment and

cleaning complete in all respects as per approved design and direction of Engineer-in-Charge.

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

140 NS- 73 Providing, fabricating, supplying and installing decorative heritage cannon of approved design and size No's 50,000.00 2.00 1,00,000.00

of 4 ft length , fabricated in metal with internal MS reinforcement if required, complete with detailed

moulded body, decorative wheels and fittings, finished in antique bronze/black metallic PU finish,

including all internal supports, base arrangement, transportation, loading, unloading, lifting,

installation, alignment, cleaning and necessary accessories complete as per approved design and

direction of Engineer-in-Charge

141 NS- 74 Providing, fabricating, supplying and fixing decorative wall plaque/inscription panel of approved No's 15,000.00 2.00 30,000.00

design and size, made of 12 mm thick MDF/HDHMR board with CNC-cut decorative profile and raised

lettering, finished with PU paint and antique gold metallic finish to selected portions, including backing,

concealed fixing arrangement, wall mounting hardware, transportation, installation, alignment and

cleaning complete in all respects as per approved design and direction of Engineer-in-Charge.

Note-All the furniture items listed below shall be inclusive of all required hardware and nothing shall

be paid extra for this

142 NS- 75 Providing, supplying and placing table of approved size and configuration complete with the following No's 27,698.75 5.00 1,38,493.75

specifications:

Polyurethane (PU) Worktop:

Worktop shall be manufactured from 25 mm thick Medium Density Fibreboard (MDF), E1 Grade,

conforming to IS:12406. The top surface shall be finished with Polyurethane (PU) paint having a

minimum 2H pencil hardness in high gloss finish, while the bottom surface shall have matte PU finish,

in approved colour as per manufacturer's standard colour chart. Worktops shall be available in the

following shapes and sizes:

Circle – Ø800 mm

Trio Leg for 4-Legged Table:

The Trio leg shall be fabricated from a combination of 1.2 mm & 2.0 mm thick CRCA steel conforming to

IS:513, and 3 mm & 5 mm thick HR steel conforming to IS:2062, forming a triangular profile. Fabrication

shall be carried out using Argon Shield Welding. The three-dimensional leg shall be inclined in two

planes and provided with an M8 ball socket leveller having a translucent bottom cap, allowing height

adjustment up to 50 mm. The complete structure shall be finished with Epoxy Polyester Powder

Coating of 40–60 microns DFT and assembled using Ni/Zn plated alloy steel hardware.

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

Cross Member / Connector: -

Cross members shall be fabricated from 50 × 25 × 1.2 mm thick ERW steel tubes conforming to IS:7138,

assembled using friction-fit PDC joinery and grub screws. The complete assembly shall be finished with

Epoxy Polyester Powder Coating of 40–60 microns DFT and fixed using Ni/Zn plated alloy steel

hardware. Cross members shall be available in lengths of 350 mm, 1100 mm and 1700 mm.

The item shall include all accessories, fittings, fasteners, assembly, placement, transportation, loading,

unloading and all incidental works complete in all respects as per the approved drawings,

manufacturer's specifications and directions of the Engineer-in-Charge.

143 NS- 76 Providing, supplying and placing table of approved size and configuration complete with the following No's 36,931.65 4.00 1,47,726.60

specifications:

Polyurethane (PU) Worktop:

Worktop shall be manufactured from 25 mm thick Medium Density Fibreboard (MDF), E1 Grade,

conforming to IS:12406. The top surface shall be finished with Polyurethane (PU) paint having a

minimum 2H pencil hardness in high gloss finish, while the bottom surface shall have matte PU finish,

in approved colour as per the manufacturer's standard colour chart. Worktops shall be available in the

following shapes and sizes:

Circle – Ø800 mm

Pod Type Under-Structure (Height – 740 mm / 1020 mm):

The under-structure shall consist of a swaged column assembly, top mounting tube frame/plate, and

square/rectangular base plate assembly. The swaged column shall be fabricated from 1.2 mm thick

CRCA steel conforming to IS:513 and 5 mm thick HR steel plates conforming to IS:2062, welded

together using Argon Shield Welding. The top mounting plate shall be of 5 mm thick HR steel

conforming to IS:2062. The base plate assembly shall be fabricated from 3 mm & 5 mm thick HR steel

plates conforming to IS:2062, 8 × 8 mm square rod, and Ø30 mm steel rod conforming to IS:432,

welded together using Argon Shield Welding. The complete under-structure shall be finished with

Epoxy Polyester Powder Coating having a DFT of 40–60 microns. The product shall have knock-down

construction and shall be assembled using alloy steel hardware with adjustable levellers at the bottom.

Cross Member / Connector: -

Cross members shall be fabricated from 50 × 25 × 1.2 mm thick ERW steel tubes conforming to IS:7138,

assembled using friction-fit PDC joinery and grub screws. The complete assembly shall be finished with

Epoxy Polyester Powder Coating of 40–60 microns DFT and assembled using Ni/Zn plated alloy steel

hardware. Cross members shall be available in lengths of 350 mm, 1100 mm and 1700 mm.

The item shall include all fittings, accessories, hardware, fasteners, assembly, placement, loading,

unloading, transportation and all incidental works complete in all respects as per the approved

drawings, manufacturer's specifications and directions of the Engineer-in-Charge.

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

144 NS- 77 Providing, supplying and placing upholstered chair of approved make, model and colour, complete with No's 39,701.50 29.00 11,51,343.50

the following specifications:

Wood Under-Structure Assembly:

The under-structure shall be manufactured from first-grade solid steamed beech wood, complete with

adjustable plinth screws/levellers. Overall under-structure size shall be 517 mm (W) × 500 mm (D) ×

The seat shall be manufactured from 12 ± 1 mm thick hot-pressed moulded plywood, cushioned with

High Resilience (HR) Polyurethane Foam of 65 ± 5 kg/m³ density, and upholstered with approved

quality fabric. Seat size shall be 495 mm (W) × 476 mm (D) × 83 mm (H).

The backrest shall be fabricated from Ø10 mm MS rod and 6 mm thick HR steel plate, conforming to

IS:2062, welded together and moulded with High Resilience (HR) Polyurethane Foam of 65 ± 5 kg/m³

density, and upholstered with approved quality fabric. Back assembly size shall be 625 mm (W) × 497

The chair shall have overall dimensions of 625 mm (W) × 633 mm (D) × 784 mm (H) with a seat height

of 450 mm. The item shall include all upholstery, stitching, hardware, fittings, finishing, assembly,

transportation, loading, unloading and placement complete in all respects as per the approved

drawings, manufacturer's specifications and directions of the Engineer-in-Charge.

145 NS- 78 Providing, supplying and placing SD-3 Single Drive Cover Mobile Storage Unit (3 Bay) of overall size No's 1,54,407.85 1.00 1,54,407.85

3600 mm (W) × 400 mm (D) × 2113 mm (H), complete with rigid knock-down construction fabricated

from 0.8 mm thick CRCA steel conforming to IS:513 Grade D. The unit shall consist of one main unit

with add-on units as required for the bay configuration and shall be finished with Epoxy Polyester

Powder Coating of minimum 40 microns DFT.

The storage shelves shall be of 12-bend construction, manufactured from 0.7 mm thick CRCA steel

conforming to IS:513 Grade D, with a uniformly distributed load capacity of 100 kg per shelf. The unit

shall provide 15 loading levels per understructure.

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

The undercarriage shall comprise a welded frame fabricated from 3 mm thick HR steel conforming to -

IS:2062. The movement shall be mechanically operated drive type, using a PU hand wheel with

sprocket-chain mechanism. Each movable undercarriage shall be provided with three driving rollers,

three driven rollers and two anti-tilt bearing assemblies, complete with die-cast step wheels, deep

groove ball bearings, MS shafts, engineering plastic wheel housings and end stoppers to ensure smooth

operation and prevent derailment.

The unit shall be provided with a centralized locking system operated through a spring mechanism on

the last drive unit, individual manual locking knobs for each drive unit, 1 mm thick CRCA drive unit

cover, aluminium label holders with transparent protective inserts, and all necessary

galvanized/blackodized/Zn plated hardware, fittings and accessories.

The item shall include complete assembly, transportation, loading, unloading, installation, testing,

commissioning and all incidental works complete in all respects as per the approved drawings,

manufacturer's specifications and directions of the Engineer-in-Charge.

The product shall be certified by CII GreenPro, UL GREENGUARD, UL GREENGUARD Gold, GRIHA and

SCS Indoor Advantage Gold

146 NS- 79 Providing, supplying and placing LD-3 Lateral Drive Cover Mobile Storage Unit (3 Bay) of overall size No's 2,42,305.15 1.00 2,42,305.15

3600 mm (W) × 400 mm (D) × 2113 mm (H), complete with rigid knock-down construction fabricated

from 0.8 mm thick CRCA steel conforming to IS:513 Grade D. The unit shall consist of one main unit

with add-on units as required for the bay configuration and shall be finished with Epoxy Polyester

Powder Coating of minimum 40 microns DFT.

The storage shelves shall be of 12-bend construction, manufactured from 0.7 mm thick CRCA steel

conforming to IS:513 Grade D, with a uniformly distributed load capacity of 100 kg per shelf. The unit

shall provide 15 loading levels per understructure.

The undercarriage shall comprise a welded frame fabricated from 3 mm thick HR steel conforming to -

IS:2062. The movement shall be mechanically operated drive type, using a PU hand wheel with

sprocket-chain mechanism. Each movable undercarriage shall be provided with three driving rollers,

three driven rollers and two anti-tilt bearing assemblies, complete with die-cast step wheels, deep

groove ball bearings, MS shafts, engineering plastic wheel housings and end stoppers to ensure smooth

operation and prevent derailment.

The unit shall be provided with a centralized locking system operated through a spring mechanism on

the last drive unit, individual manual locking knobs for each drive unit, 1 mm thick CRCA drive unit

cover fixed on the last unit (LD), aluminium label holders with transparent protective inserts, and all

necessary galvanized/blackodized/Zn plated hardware, fittings and accessories.

The item shall include complete assembly, transportation, loading, unloading, installation, testing,

commissioning and all incidental works complete in all respects as per the approved drawings,

manufacturer's specifications and directions of the Engineer-in-Charge.

The product shall be certified by CII GreenPro, UL GREENGUARD, UL GREENGUARD Gold, GRIHA and

SCS Indoor Advantage Gold

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

147 NS- 80 Providing, supplying and placing TD-3 Twin Drive Mobile Storage Unit (3 Bay) of overall size 3600 mm No's 3,24,642.60 1.00 3,24,642.60

(W) × 800 mm (D) × 2113 mm (H), complete with rigid knock-down construction fabricated from 0.8

mm thick CRCA steel conforming to IS:513 Grade D. The unit shall consist of one main unit with add-on

units as required for the bay configuration and shall be finished with Epoxy Polyester Powder Coating

of minimum 40 microns DFT.

The storage shelves shall be of 12-bend construction, manufactured from 0.7 mm thick CRCA steel

conforming to IS:513 Grade D, with a uniformly distributed load capacity of 100 kg per shelf. The unit

shall provide 30 loading levels per understructure.

The undercarriage shall comprise a welded frame fabricated from 3 mm thick HR steel conforming to -

IS:2062. The movement shall be mechanically operated drive type, using a PU hand wheel with

sprocket-chain mechanism. Each movable undercarriage shall be provided with three driving rollers,

three driven rollers and two anti-tilt bearing assemblies, complete with die-cast step wheels, deep

groove ball bearings, MS shafts, engineering plastic wheel housings and end stoppers to ensure smooth

operation and prevent derailment.

The unit shall be provided with hinged doors on the last Twin Drive (TD) body, a centralized locking

system operated through a spring mechanism, individual manual locking knobs for each drive unit, 1

mm thick CRCA drive unit cover, aluminium label holders with transparent protective inserts, and all

necessary galvanized/blackodized/Zn plated hardware, fittings and accessories.

The storage unit shall be available in heights of 1980 mm and 2361 mm, as specified in the

drawings/schedule.

The item shall include complete assembly, transportation, loading, unloading, installation, testing,

commissioning and all incidental works complete in all respects as per the approved drawings,

manufacturer's specifications and directions of the Engineer-in-Charge.

The product shall be certified by CII GreenPro, UL GREENGUARD, UL GREENGUARD Gold, GRIHA and

SCS Indoor Advantage Gold

148 NS- 81 The guide rail system shall consist of 'C' section fabricated from 2.0 mm thick HR steel sheet and 25.4 × No's 54,255.95 1.00 54,255.95

25.4 × 2.0 mm thick ERW square steel tube, rigidly connected using screws. The guide channels shall be

accurately aligned and securely fixed to the finished floor using approved rawl plugs and screws,

ensuring the floor is level prior to installation. Guide rail channels shall be available in standard lengths

of 800 mm, 1600 mm and 2400 mm, complete with all necessary fittings, fasteners and accessories as

per the manufacturer's specifications.

149 NS- 82 Providing, supplying and placing 52.4 mm thick, 1200 mm high modular partition panels in Wish No's 92,329.10 146.00 1,34,80,048.60

System, comprising a combination of bottom metal raceway, two intermediate fabric-finished blocks,

and top fabric magnetic tile, complete with panel frame, connectors, clips and all necessary accessories.

The panel shall be designed to accommodate cable management through the integrated metal raceway

and shall be finished with approved fabric upholstery on exposed surfaces.

The panel shall be supported on powder-coated steel legs of approved design and finish, complete with

levellers, fixing hardware, connectors, assembly, transportation, loading, unloading and placement. The

item shall include all fittings, fasteners and incidental works complete in all respects as per the

approved drawings, manufacturer's specifications and directions of the Engineer-in-Charge

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

150 NS- 83 Providing, supplying and placing 52.4 mm thick, 1200 mm high modular workstation panel in Wish No's 83,935.55 4.00 3,35,742.20

System, comprising a bottom metal raceway for cable management, two intermediate fabric-finished

blocks, and a top fabric magnetic tile, complete with internal frame, connectors, clips and all necessary

fixing accessories. The panel shall be supported on powder-coated steel legs with adjustable levellers

and finished in approved colour and fabric. The item shall include complete assembly, transportation,

loading, unloading, installation and all necessary hardware, fittings and incidental works complete in all

respects as per the approved drawings, manufacturer's specifications and directions of the Engineer-in-

151 NS- 84 Providing, supplying and placing 52.4 mm thick, 1200 mm high modular workstation panel in Wish No's 1,20,027.85 30.00 36,00,835.50

System, comprising a sturdy steel panel frame with a bottom metal raceway for concealed cable

management, two intermediate fabric-finished acoustic blocks, and a top fabric magnetic tile, complete

with all connectors, junctions, end trims, clips and fixing accessories. The panel shall be supported on

powder-coated steel legs with adjustable levellers and finished in approved colour and fabric. The item

shall include complete assembly, transportation, loading, unloading, installation and all necessary

hardware, fittings and incidental works complete in all respects as per the approved drawings,

manufacturer's specifications and directions of the Engineer-in-Charge.

152 NS- 85 Providing, supplying and placing Upbeat Modular Desk Based Workstation of 1200 mm overall height, No's 58,754.90 - -

complete with Cello legs having inclination in one plane and provided with aluminium alloy extrusion

covers in approved colour and finish. The workstation shall be provided with an integrated wire tray

incorporating a power box and switch plate (8+3 Anchor Roma or equivalent), complete with soft-

closing access flap and brush cable manager for concealed cable management.

The workstation shall be provided with a metal modesty panel fabricated from 0.8 mm thick CRCA

steel, securely fixed to the worktop using 3 mm thick HR steel mounting brackets. An 18 mm thick T-

mould fabric screen shall be mounted on studs over the worktop. The worktop shall be 25 mm thick

pre-laminated particle board finished with PVC edge lipping on all exposed edges.

The item shall include all connectors, brackets, hardware, fasteners, levellers, cable management

accessories, assembly, transportation, loading, unloading, installation and all incidental works complete

in all respects as per the approved drawings, manufacturer's specifications and directions of the

Engineer-in-Charge.

153 NS- 86 Providing, supplying and placing Upbeat Modular Desk Based Workstation of 750 mm overall height, No's 63,791.00 4.00 2,55,164.00

complete with Cello legs having inclination in one plane and provided with aluminium alloy extrusion

covers in approved colour and finish. The workstation shall be provided with a single power box with

wire management system for Manager Modules/Single Tables, complete with (8+3 Anchor Roma or

equivalent) switch plate, soft-closing access flap and brush cable manager for concealed cable routing.

The workstation shall be provided with a metal modesty panel fabricated from 0.8 mm thick CRCA

steel, securely fixed to the worktop using 3 mm thick HR steel mounting brackets. The worktop shall be

25 mm thick pre-laminated particle board with PVC edge lipping on all exposed edges.

The item shall include all connectors, brackets, cable management accessories, hardware, fasteners,

levellers, assembly, transportation, loading, unloading, installation and all incidental works complete in

all respects as per the approved drawings, manufacturer's specifications and directions of the Engineer-

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

154 NS- 87 Providing, supplying and placing Upbeat Modular Desk Based Workstation of 750 mm height, No's 70,505.85 - -

comprising Cello legs with inclination in one plane and aluminium alloy extrusion covers in approved

colour and finish. The workstation shall be provided with an integrated wire management system

consisting of a single power box with raiser for Manager Modules/Single Tables, complete with (8+3

Anchor Roma or equivalent) switch plate, soft-closing access flap and brush cable manager.

The workstation shall be provided with a metal modesty panel fabricated from 0.8 mm thick CRCA

steel, securely mounted to the worktop using 3 mm thick HR steel brackets. The worktop shall be 25

mm thick pre-laminated particle board with PVC edge lipping on all exposed edges.

The item shall include all brackets, connectors, cable management accessories, hardware, fasteners,

levellers, assembly, transportation, loading, unloading, installation and all incidental works complete in

all respects as per the approved drawings, manufacturer's specifications and directions of the Engineer-

155 NS- 88 Providing, supplying and placing Mid Back Ergonomic Chair complete with upholstered seat and mesh No's 19,264.90 188.00 36,21,801.20

back, having the following specifications:

The seat shall be manufactured from 15 ± 1 mm thick hot-pressed plywood, upholstered with fabric

and moulded High Resilience (HR) Polyurethane foam, with extra-thick front edge cushioning for

enhanced popliteal comfort. The backrest shall be injection moulded in glass-filled polypropylene

upholstered with mesh fabric, and provided with an adjustable lumbar support made of injection

moulded polypropylene having 50 ± 1 mm adjustment. Seat size shall be 535 mm (W) × 510 mm (D)

and mesh back size 510 mm (W) × 700 mm (H).

The HR Polyurethane seat foam shall have a density of 45 ± 2 kg/m³ and hardness of 16 ± 2 kgf at 25%

compression conforming to IS:7888. The chair shall be provided with height-adjustable armrests having

6-step adjustment with a travel of 72 ± 5 mm, comprising glass-filled nylon armrest structure with PU

moulded arm pads.

The chair shall be fitted with a Centre Tilt Synchro Mechanism with 360° swivel, 3-position locking, anti- -

shock mechanism, and tilt tension adjustment. Pneumatic height adjustment shall provide a stroke of

The pedestal shall be injection moulded in glass-filled nylon, fitted with five twin-wheel nylon castors,

having a pitch centre diameter of 661 ± 5 mm (761 ± 10 mm with castors). Overall chair dimensions

shall be 761 mm (W) × 761 mm (D) × 1015–1110 mm (H) with seat height adjustable from 445 mm to

The item shall include complete assembly, transportation, loading, unloading, placement and all

fittings, accessories and hardware complete in all respects as per the approved drawings,

manufacturer's specifications and directions of the Engineer-in-Charge.

The product shall be certified by CII GreenPro, UL GREENGUARD, GRIHA, SCS Indoor Advantage Gold

and BIFMA LEVEL 2.

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

156 NS- 89 Providing, supplying and placing High Back Ergonomic Chair complete with upholstered seat, mesh No's 21,044.30 4.00 84,177.20

back and adjustable headrest, having the following specifications:

The seat shall be manufactured from 15 ± 1 mm thick hot-pressed plywood, upholstered with fabric

and moulded High Resilience (HR) Polyurethane foam, with extra-thick front edge cushioning for

enhanced popliteal comfort. The backrest shall be injection moulded in glass-filled polypropylene

upholstered with mesh fabric, and provided with an adjustable lumbar support made of injection

moulded polypropylene having 50 ± 1 mm adjustment. Seat size shall be 535 mm (W) × 510 mm (D)

and mesh back size 510 mm (W) × 700 mm (H).

The HR Polyurethane seat foam shall have a density of 45 ± 2 kg/m³ and hardness of 16 ± 2 kgf at 25%

compression conforming to IS:7888. The chair shall be provided with height-adjustable armrests having

6-step adjustment with a travel of 72 ± 5 mm, comprising glass-filled nylon armrest structure with PU

moulded arm pads.

The chair shall be fitted with a Centre Tilt Synchro Mechanism featuring 360° swivel, 3-position locking, -

anti-shock mechanism and tilt tension adjustment. It shall also be provided with an adjustable headrest

comprising an injection moulded glass-filled polypropylene frame, upholstered with moulded HR

polyurethane foam and fabric, with a 40 ± 1 mm height adjustment.

The chair shall have pneumatic height adjustment with a stroke of 95 ± 3 mm. The pedestal shall be

injection moulded in glass-filled nylon, fitted with five twin-wheel black nylon castors, having a pitch

centre diameter of 661 ± 5 mm (761 ± 10 mm with castors). Overall chair dimensions shall be 761 mm

(W) × 761 mm (D) × 1170–1300 mm (H) with seat height adjustable from 445 mm to 540 mm.

The item shall include complete assembly, transportation, loading, unloading, placement, all fittings,

accessories and hardware complete in all respects as per the approved drawings, manufacturer's

specifications and directions of the Engineer-in-Charge.

The product shall be certified by CII GreenPro, UL GREENGUARD, GRIHA, SCS Indoor Advantage Gold

and BIFMA LEVEL 2

157 NS- 90 Providing, supplying and placing Executive Table with ERU (Extended Return Unit) and Integrated No's 1,58,074.15 1.00 1,58,074.15

Pedestal of overall size 1650 × 1950 × 750 mm, complete with the following specifications:

The primary work surface shall be manufactured from 25 mm thick MDF, one side pre-laminated board

conforming to IS:14587:1998, finished with 0.4 mm PVC membrane pressed on the top surface and

provided with a soft-closing access flap incorporating an in-built power box for wire management.

The secondary work surface and modesty panel shall be manufactured from 25 mm thick MDF, one

side pre-laminated board conforming to IS:14587:1998, finished with 0.4 mm PVC membrane pressed

on the top surface.

The understructure and integrated pedestal shall be manufactured from 25 mm thick pre-laminated

Twin Board of E1-P2 Grade, conforming to IS:12823:1990, in approved shade and finished with 2 mm

thick matching PVC edge banding on all exposed edges.

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

The drawer fronts shall be manufactured from 25 mm thick MDF, one side pre-laminated board -

conforming to IS:14587:1998, with 0.4 mm PVC membrane pressed on the top surface. The integrated

pedestal shall be of Box–Box–File configuration, provided with 400 mm long powder-coated metal

drawer slides having 325 mm drawer extension, complete with soft-closing and anti-slam mechanism,

ergonomic handles and a central locking arrangement for security.

The item shall include all fittings, hardware, power access accessories, connectors, assembly,

transportation, loading, unloading, installation and all incidental works complete in all respects as per

the approved drawings, manufacturer's specifications and directions of the Engineer-in-Charge

158 NS- 91 Providing, supplying and placing Executive Table with ERU (Extended Return Unit) and Integrated No's 1,60,493.20 24.00 38,51,836.80

Pedestal of overall size 1800 × 2100 × 750 mm, complete with the following specifications:

The primary work surface shall be manufactured from 25 mm thick MDF, one side pre-laminated board

conforming to IS:14587:1998, finished with 0.4 mm PVC membrane pressed on the top surface and

provided with a soft-closing access flap incorporating an in-built power box for wire management.

The secondary work surface and modesty panel shall be manufactured from 25 mm thick MDF, one

side pre-laminated board conforming to IS:14587:1998, finished with 0.4 mm PVC membrane pressed

on the top surface.

The understructure and integrated pedestal shall be manufactured from 25 mm thick pre-laminated

Twin Board of E1-P2 Grade, conforming to IS:12823:1990, in approved shade and finished with 2 mm

thick matching PVC edge banding on all exposed edges.

The drawer fronts shall be manufactured from 25 mm thick MDF, one side pre-laminated board -

conforming to IS:14587:1998, with 0.4 mm PVC membrane pressed on the top surface. The integrated

pedestal shall be of Box–Box–File configuration, provided with 400 mm long powder-coated metal

drawer slides having 325 mm drawer extension, complete with soft-closing and anti-slam mechanism,

ergonomic handles and a central locking arrangement for security.

The item shall include all fittings, hardware, power access accessories, connectors, assembly,

transportation, loading, unloading, installation and all incidental works complete in all respects as per

the approved drawings, manufacturer's specifications and directions of the Engineer-in-Charge.

159 NS- 92 Providing, supplying and placing Back Storage Unit of overall size 1650 × 500 × 750 mm, complete with No's 86,139.70 25.00 21,53,492.50

the following specifications:

The top panel shall be manufactured from 25 mm thick MDF, one side pre-laminated board conforming

to IS:14587:1998, finished with 0.4 mm PVC membrane pressed on the top surface.

The sliding door storage unit shall be manufactured from 25 mm thick pre-laminated Twin Board of E1-

P2 Grade, conforming to IS:12823:1990, in approved shade, with all body components including side

panels, bottom panel, back panel and shelves finished with 2 mm thick matching PVC edge banding on

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

The sliding shutters shall be manufactured from 25 mm thick MDF, one side pre-laminated board -

conforming to IS:14587:1998, finished with 0.4 mm PVC membrane pressed on the top surface. The

shutters shall be provided with soft-closing and anti-slam mechanism, ergonomic handles and a locking

arrangement for security.

The item shall include all fittings, hardware, locking system, sliding mechanisms, connectors, assembly,

transportation, loading, unloading, installation and all incidental works complete in all respects as per

the approved drawings, manufacturer's specifications and directions of the Engineer-in-Charge

160 NS- 93 Providing, supplying and placing High Back Executive Ergonomic Chair complete with leatherette No's 41,580.00 25.00 10,39,500.00

upholstered seat and back, having the following specifications:

The seat assembly shall comprise injection moulded plastic outer and inner shells, with the inner shell

upholstered in leatherette and cushioned with moulded High Resilience (HR) Polyurethane Foam of 45

± 2 kg/m³ density and 16 ± 2 kgf hardness at 25% compression conforming to IS:7888. The back

assembly shall comprise moulded PU foam with an in-situ moulded MS ERW round tube of Ø19 ± 0.3

mm × 1.6 ± 0.128 mm thickness, upholstered in leatherette. Seat size shall be 470 mm (W) × 480 mm

(D) and high back size 477 mm (W) × 764 mm (H).

The chair shall be provided with height-adjustable drop-lift armrests fabricated from Ø38.1 ± 0.3 mm ×

2.0 ± 0.1 mm thick MS ERW tubular supports with chrome-plated finish and PU moulded arm pads,

offering 65 ± 5 mm height adjustment in 5 steps.

The chair shall be fitted with an Active Bio-Synchro Mechanism with 360° swivel, front-pivot -

synchronized tilt, continuous lumbar support, seat/back tilt ratio of 1:2, 5-position tilt limiter, tilt

tension adjustment operable while seated, and black powder-coated HPDC aluminium mechanism

housing. The seat shall incorporate an integrated sliding mechanism providing 60 ± 5 mm seat depth

adjustment. The back support shall be mounted on a plastic T-spine with 74.2 ± 5 mm height

adjustment for personalized lumbar support.

The chair shall be provided with pneumatic height adjustment having a 100 ± 3 mm stroke. The

pedestal shall be manufactured from high-pressure die-cast polished aluminium fitted with five twin-

wheel black polypropylene castors of 60 ± 1 mm diameter, with a pedestal pitch centre diameter of 650

± 5 mm (750 ± 10 mm with castors).

Overall chair dimensions shall be 761 mm (W) × 761 mm (D) × 1127–1302 mm (H) with seat height -

adjustable from 431 mm to 531 mm.

The item shall include complete assembly, transportation, loading, unloading, placement, all fittings,

accessories and hardware complete in all respects as per the approved drawings, manufacturer's

specifications and directions of the Engineer-in-Charge.

The product shall be certified by CII GreenPro, UL GREENGUARD, GRIHA, SCS Indoor Advantage Gold

and BIFMA LEVEL 2.

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

161 NS- 94 Providing, supplying and placing Mid Back Executive Ergonomic Chair complete with leatherette No's 38,806.75 75.00 29,10,506.25

upholstered seat and back, having the following specifications:

The seat assembly shall comprise injection moulded plastic outer and inner shells, with the inner shell

upholstered in leatherette and cushioned with moulded High Resilience (HR) Polyurethane Foam of 45

± 2 kg/m³ density and 16 ± 2 kgf hardness at 25% compression conforming to IS:7888. The back

assembly shall comprise moulded PU foam with an in-situ moulded MS ERW round tube of Ø19 ± 0.3

mm × 1.6 ± 0.128 mm thickness, upholstered in leatherette. Seat size shall be 470 mm (W) × 480 mm

(D) and mid back size 477 mm (W) × 601 mm (H).

The chair shall be provided with height-adjustable drop-lift armrests fabricated from Ø38.1 ± 0.3 mm ×

2.0 ± 0.1 mm thick MS ERW tubular supports with chrome-plated finish and PU moulded arm pads,

offering 65 ± 5 mm height adjustment in 5 steps.

The chair shall be fitted with an Active Bio-Synchro Mechanism featuring 360° swivel, front-pivot -

synchronized tilt, continuous lumbar support, 5-position tilt limiter, seat/back tilt ratio of 1:2, tilt

tension adjustment operable while seated, and black powder-coated HPDC aluminium mechanism

housing. The seat shall incorporate an integrated sliding mechanism providing 60 ± 5 mm seat depth

adjustment, while the back support shall be mounted on a plastic T-spine with 74.2 ± 5 mm height

adjustment for optimum ergonomic support.

The chair shall be provided with pneumatic height adjustment having a 100 ± 3 mm stroke. The

pedestal shall be manufactured from high-pressure die-cast polished aluminium fitted with five twin-

wheel black polypropylene castors of 60 ± 1 mm diameter, with a pedestal pitch centre diameter of 650

± 5 mm (750 ± 10 mm with castors).

Overall chair dimensions shall be 761 mm (W) × 761 mm (D) × 965–1140 mm (H) with seat height

adjustable from 431 mm to 531 mm.

The item shall include complete assembly, transportation, loading, unloading, placement, all fittings,

accessories and hardware complete in all respects as per the approved drawings, manufacturer's

specifications and directions of the Engineer-in-Charge.

The product shall be certified by CII GreenPro, UL GREENGUARD, GRIHA, SCS Indoor Advantage Gold

and BIFMA LEVEL 2.

162 NS- 95 Providing, supplying and placing Echo HDU Wooden Storage Unit (low height/medium height) of No's 23,258.55 1.00 23,258.55

approved size and configuration, complete with the following specifications:

The body shall be manufactured from 18 mm thick pre-laminated board (PLB) with all exposed edges

sealed with 0.8 mm thick PVC edge banding. The back panel shall be 9 mm thick white pre-laminated

board (PLT). The storage unit shall be of knock-down (KD) construction, assembled using suitable KD

The shelves and separator panels (where provided) shall be manufactured from 18 mm thick white pre-

laminated board (PLT) with 0.8 mm thick PVC edge banding. The bottom shelf shall be fixed, while the

remaining shelves shall be adjustable to optimize storage space.

The door shutters shall be manufactured from 18 mm thick pre-laminated board (PLB) with 2 mm thick

PVC edge banding on all edges and provided with flush-type plastic handles fixed vertically at the

centre. The hinged doors shall be fitted with approved quality hinges and adjustable fittings for proper

alignment and height adjustment.

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

The storage unit shall be provided with a three-point locking system for security and 6 mm adjustable -

levellers at the bottom for proper levelling on finished floors.

The item shall include all fittings, hinges, locks, handles, shelf supports, KD fittings, levellers, hardware,

assembly, transportation, loading, unloading, installation and all incidental works complete in all

respects as per the approved drawings, manufacturer's specifications and directions of the Engineer-in-

163 NS- 96 Providing, supplying and placing Echo HDU wooden storage unit of approved size and configuration No's 24,091.20 5.00 1,20,456.00

(low height/medium height), comprising 18 mm thick pre-laminated board (PLB) body with all exposed

edges sealed with 0.8 mm thick PVC edge banding. The back panel shall be 9 mm thick white pre-

laminated board (PLT). The unit shall be of knock-down (KD) construction assembled using suitable KD

The shelves and separator panels (where applicable) shall be manufactured from 18 mm thick white

pre-laminated board (PLT) with 0.8 mm thick PVC edge banding. The bottom shelf shall be fixed, while

the remaining shelves shall be adjustable to optimize storage space.

The hinged door shutters shall be manufactured from 18 mm thick pre-laminated board (PLB) with 2

mm thick PVC edge banding on all edges and provided with flush-type plastic handles fixed vertically at

the centre. The doors shall be fitted with approved quality hinges, adjustable fittings for alignment and

height adjustment, and a three-point locking system for security.

The storage unit shall be provided with 6 mm adjustable levellers at the base for proper levelling. The -

item shall include all hinges, locks, handles, shelf supports, KD fittings, levellers, hardware, assembly,

transportation, loading, unloading, installation and all incidental works complete in all respects as per

the approved drawings, manufacturer's specifications and directions of the Engineer-in-Charge

164 NS- 97 Providing, supplying and placing wooden storage unit with hinged doors and drawers of approved size No's 37,603.15 4.00 1,50,412.60

and configuration, complete with the following specifications:

The body shall be manufactured from 18 mm thick pre-laminated board (PLB). The side and bottom

panels shall be of 18 mm thick PLB finished with 0.8 mm thick PVC edge banding. The top panel shall be

25 mm thick PLB with 2 mm thick PVC edge banding on exposed edges. The back panel and

shelf/separator panels (where provided) shall be manufactured from 18 mm thick pre-laminated board

(PLT) with 0.8 mm thick PVC edge banding.

The drawer assembly shall comprise 18 mm thick PLB drawer fascia with 2 mm PVC edge banding, 18

mm thick PLB back panel with 0.8 mm PVC edge banding, and 6 mm thick MDF bottom panel. Drawers

shall be fitted with anodized aluminium handles and powder-coated single extension full-panel roller

drawer slides. The file drawer shall be provided with a fifth roller arrangement for smooth operation

and enhanced load capacity. Standard drawer sizes shall be 323 mm (W) × 376 mm (D) × 73 mm (H) for

box drawers and 293 mm (W) × 376 mm (D) × 208 mm (H) for file drawers.

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

The hinged door shutters shall be manufactured from 18 mm thick PLB with 2 mm thick PVC edge -

banding and fitted with approved quality hinges.

The item shall include all shelves, drawers, hinges, handles, drawer slides, fittings, hardware, assembly,

transportation, loading, unloading, installation and all incidental works complete in all respects as per

the approved drawings, manufacturer's specifications and directions of the Engineer-in-Charge.

165 NS- 98 Providing, supplying and placing steel storage unit of approved size and configuration with aesthetically No's 32,761.75 27.00 8,84,567.25

designed knock-down construction, fabricated from CRCA 'D' Grade steel conforming to IS:513,

comprising 0.5 mm thick side, bottom and back panels (back panel 1.2 mm thick for 600 mm and 1200

mm wide units), 1.2 mm thick top/bottom stiffeners, 0.6 mm thick end covers, and finished with Epoxy

Polyester Powder Coating of 50 ± 10 microns DFT.

The unit shall be provided with either a 0.6 mm thick CRCA metal top panel finished with epoxy

polyester powder coating or a 25 mm thick pre-laminated board (PLB) conforming to IS:14587:1998,

finished with 2 mm thick matching PVC edge banding, as specified.

The storage unit shall be provided with 12-bend fixed shelves fabricated from 0.7 mm thick CRCA steel,

capable of storing A4 box files (85 × 345 × 285 mm) vertically. The unit shall have one fixed shelf for

750 mm height and two fixed shelves for taller units, with each shelf having a uniformly distributed

load capacity of 74 kg for 1200 mm wide units.

The unit shall be provided with adjustable screw-type levellers mounted on 1.6 mm thick CRCA base -

plates, offering 25 mm height adjustment, complete with plastic base for floor levelling. Open shelf

units shall be provided with die-cast hinge cover caps finished with epoxy polyester powder coating

and 120 × 18 mm polyester name tag stickers fixed to the shelves.

The metal door shutters shall be fabricated from 0.6 mm thick CRCA steel with 0.5 mm thick CRCA

stiffeners, finished with Epoxy Polyester Powder Coating of 50 ± 10 microns DFT, and fitted with soft-

closing hinges having 105° opening, integrated handles, and a three-way cam locking system with click-

action mechanism, zinc alloy die-cast housing and removable keys in both locked and unlocked

positions. Doors shall be provided in sizes suitable for the specified storage unit dimensions and shall

be fitted with 120 × 18 mm polyester name tag stickers at the top left corner.

The item shall include all shelves, doors, locks, hinges, handles, levellers, name tags, fittings, hardware,

assembly, transportation, loading, unloading, installation and all incidental works complete in all

respects as per the approved drawings, manufacturer's specifications and directions of the Engineer-in-

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

166 NS- 99 Providing, supplying and placing Steel Storage Unit of approved size and configuration with No's 1,02,829.45 1.00 1,02,829.45

aesthetically designed knock-down construction, fabricated from CRCA 'D' Grade steel conforming to

IS:513. The unit shall comprise 0.5 mm thick CRCA side and bottom panels, 0.5 mm/1.2 mm thick back

panel (as applicable to unit width and height), 1.2 mm thick top and bottom stiffeners, and 0.6 mm

thick end covers, all finished with Epoxy Polyester Powder Coating of 50 ± 10 microns DFT.

The unit shall be provided with either a 0.6 mm thick CRCA bent metal top, powder coated to match, or

a 25 mm thick pre-laminated board (PLB) conforming to IS:14587:1998, finished with 2 mm thick

matching PVC edge banding, as specified.

The storage unit shall be fitted with 12-bend fixed shelves fabricated from 0.7 mm thick CRCA steel

(IS:513, Grade D), suitable for storing A4 box files vertically. The unit shall have one fixed shelf for 750

mm high units and two fixed shelves for taller units, with each shelf having a uniformly distributed load

capacity of 74 kg for 1200 mm wide units.

The unit shall be provided with adjustable screw-type levellers mounted on 1.6 mm thick CRCA base -

plates, with 25 mm adjustment for proper levelling. Open shelf units shall be provided with powder-

coated die-cast hinge cover caps and 120 × 18 mm polyester name tag holders fixed to the shelves.

The door shutters shall be fabricated from 0.6 mm thick CRCA steel reinforced with 0.5 mm thick CRCA

stiffeners, finished with Epoxy Polyester Powder Coating of 50 ± 10 microns DFT, and fitted with 105°

soft-closing hinges, integrated handles, and a three-way cam locking system with click-action

mechanism, zinc die-cast housing and removable keys in both locked and unlocked positions. Each door

shall be provided with a 120 × 18 mm polyester name tag holder at the top corner.

The item shall include all shelves, doors, hinges, locks, handles, levellers, name tag holders, fittings,

hardware, assembly, transportation, loading, unloading, installation and all incidental works complete

in all respects as per the approved drawings, manufacturer's specifications and directions of the

Engineer-in-Charge.

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

167 NS- 100 Providing, supplying and placing of Storage Unit .CONSTRUCTION AND MATERIAL No's 1,35,242.00 1.00 1,35,242.00

1)Aesthetically appealing completely knock down construction.

2)Made from combination of side panel(0.5mm CRCA), Bottom panel(0.5mmCRCA), Back panel(0.5mm

for 750mm and 900width Storage Units and 1.2mmCRCA for 600mm and 1200width Storage Units to

avoid toppling of unit in caseof Glass door unit and single door unit), Top Bottom stiffener(1.2mm

CRCA) andEnd Cover(0.6mm CRCA). CRCA 'D' Grade as per IS-513

3)All metal panels are coated with Epoxy polyster powder of 50±10 microns

For top panel two options available

1)Metal Top Panel (0.6mm CRCA) bent panel which is powder coated with Epoxypolyster powder of

50±10 microns thickness.

2)Wood Top Panel (Made of 25mm thick pre-laminate board (PLB) conformingto IS-14587:1998, Edge

banded with matching 2 mm thick PVC lipping )

1)Fixed shelves made up of 12 bend panel made of 0.7mm Thick CRCA (D Grade, IS-513)

2)1 No. fixed shelf for 750mm height and 2NO. Fixed shelf for other remaining heights

3)A4 size box file (85Wx345Hx285D) can be stored vertically.

4)Number of files that can be stored per shelf is :

For width 1200w - 13 Nos.

5)Each shelf has max Load Capacity of -

74kg UDL for 1200W unit

- Metal base plate (1.6mm CRCA) with Screw type adjustable leveler with plasticbase provides vertical

adjustment for floor unevenness and leveling of units.

- Height of Leveller is 50mm and 25mm Leveller adjustment available

HINGE COVER CAP

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

168 NS- 101 Providing, supplying and placing of Storage Unit .CONSTRUCTION AND MATERIAL No's 1,67,654.55 1.00 1,67,654.55

1)Aesthetically appealing completely knock down construction.

2)Made from combination of side panel(0.5mm CRCA), Bottom panel(0.5mmCRCA), Back panel(0.5mm

for 750mm and 900width Storage Units and 1.2mmCRCA for 600mm and 1200width Storage Units to

avoid toppling of unit in caseof Glass door unit and single door unit), Top Bottom stiffener(1.2mm

CRCA) andEnd Cover(0.6mm CRCA). CRCA 'D' Grade as per IS-513

3)All metal panels are coated with Epoxy polyster powder of 50±10 microns

For top panel two options available

1)Metal Top Panel (0.6mm CRCA) bent panel which is powder coated with Epoxypolyster powder of

50±10 microns thickness.

2)Wood Top Panel (Made of 25mm thick pre-laminate board (PLB) conformingto IS-14587:1998, Edge

banded with matching 2 mm thick PVC lipping )

1)Fixed shelves made up of 12 bend panel made of 0.7mm Thick CRCA (D Grade, IS-513)

2)1 No. fixed shelf for 750mm height and 2NO. Fixed shelf for other remaining heights

3)A4 size box file (85Wx345Hx285D) can be stored vertically.

4)Number of files that can be stored per shelf is :

For width 1200w - 13 Nos.

5)Each shelf has max Load Capacity of -

74kg UDL for 1200W unit

- Metal base plate (1.6mm CRCA) with Screw type adjustable leveler with plasticbase provides vertical

adjustment for floor unevenness and leveling of units.

- Height of Leveller is 50mm and 25mm Leveller adjustment available

169 NS- 102 HINGE COVER

Providing, CAP and placing of one seater sofa. SEAT FOAM : The seat is made up of PU foam in

Density 28 ±2 kg/cu.mtr with an additional top layer of supersoft PU foam in Density 32 ± 2 kg/cu,

upholstered with fabric or leatherette.

BACK FOAM : The back is made up of PU foam in Density 28 ± 2 kg/cu. mtr with two additional top layer

of supersoft foam of density 32±2 kg/cu. mtr, upholstered with fabric or leatherette.

UNDERSTRUCTRE : Understructure is made up of 1.2±0.1 cm. thick hot pressed plywood [moisture

resistance & termite proof as per IS:303] & pinewood of cross sections devoid of major knots & surface

defects. 6 nos. per seat & 3.8mm Dia zigzag spring assembly is mounted over understructure for

cushioning purpose.

LEG ASSEMBLY : It is a welded Assembly made in Stainless steel (grade SS 202) tube & plate with plastic

Width (W): 86.0 CM. Depth (D): 90.5 CM. Height (H): 85.5 CM. Seat Height (SH): 45.0 CM.

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

170 NS- 103 Providing, supplying and placing of two seater sofa. SEAT FOAM : The seat is made up of PU foam in No's 65,555.35 3.00 1,96,666.05

Density 28 ±2 kg/cu.mtr with an additional top layer of supersoft PU foam in Density 32 ± 2 kg/cu,

upholstered with fabric or leatherette.

BACK FOAM : The back is made up of PU foam in Density 28 ± 2 kg/cu. mtr with two additional top layer

of supersoft foam of density 32±2 kg/cu. mtr, upholstered with fabric or leatherette.

UNDERSTRUCTRE : Understructure is made up of 1.2±0.1 cm. thick hot pressed plywood [moisture

resistance & termite proof as per IS:303] & pinewood of cross sections devoid of major knots & surface

defects. 6 nos. per seat & 3.8mm Dia zigzag spring assembly is mounted over understructure for

cushioning purpose.

LEG ASSEMBLY : It is a welded Assembly made in Stainless steel (grade SS 202) tube & plate with plastic

Width (W): 146.0 CM. Depth (D): 90.5 CM. Height (H): 85.5 CM. Seat Height (SH): 45.0 CM.

171 NS- 104 Providing, supplying and placing of coffee table. CENTER TABLE GLASS: It is 10 ±0.3 mm thick black No's 25,482.85 1.00 25,482.85

tinted Toughened glass UV glued with bushes made in SS 202 grade for focing with understructure.

CENTER TABLE UNDERSTRUCTURE: It is a welded Assembly made in SS202 grade

Dia. 12±0.04 as per IS:1762.

Width of table= 112.0 cm, Depth=60.0 cm, height=34.9 cm.

172 NS- 105 Providing, supplying and placing of side table. SIDE TABLE GLASS: It is 10 ±0.3 mm thick black tinted No's 16,931.50 2.00 33,863.00

Toughened glass UV glued with bushes made in SS 202 grade for focing with understructure.

SIDE TABLE UNDERSTRUCTURE: It is a welded Assembly made in SS202 grade

Dia. 12±0.04 as per IS:1762.

Width of table= 60.0 cm, Depth=60.0 cm, height=34.9 cm.

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

173 NS- 106 Providing, supplying and placing of public seating. SEAT SHELL : The Seat is made from high density self- No's 76,942.00 14.00 10,77,188.00

skin Polyurethane foam reinforced with 1.2 mm M.S. perforated sheet insert. The Polyurethane foam

having density of min. 350 kg/m3 with a Shore 'A' hardness of 60±10.

SEAT SIZE : 52.0 cm (W) x 50.5 cm (D)

BACK SHELL : The Back is made from high density self-skin Polyurethane foam reinforced with 1.2 mm

M.S. perforated sheet insert.The Polyurethane Foam having density of min. 350 kg/m3 with a Shore 'A'

hardness of 60±10.

BACK SIZE : 52.0 cm (W) x 53.5 cm (H)

CROSS BEAM : Cross Beam made up of Diamond shaped double wall Extrusion of Aluminum 6063-T6

Alloy with coated of 50 micron epoxy polyester coating and fitted with Polypropylene Copolymer

engineering plastic end caps.

CROSS BEAM SIZE : 11.3 cm (W) x 9.4 cm (H) X 0.4 cm (Thickness).

LEG : Legs are made up of High pressure Aluminum ADC12 Die cast coated with 50 micron epoxy

polyester coating, Leg Are fitted with soft grip PVC level adjusting shoes.

ARMREST : Armrest are made up of High pressure Aluminum ADC12 die cast coated with 50 micron

epoxy polyester coating.

SEAT SUPPORT BRACKET Assembly : Seat support bracket assembly made up of argon shield welding of

Hot Rolled Steel (IS: 2062) 0.3cm Thickness. This welded structure is coated with 50 micron epoxy

polyester coating.

CLAMPING BRACKET : Clamping bracket are made up of Hot Rolled Steel (IS: 2062) 0.3cm Thickness

coated with 50 micron epoxy polyester coating.Overall Dimensions of Chair

Seat Height - 42.5 cm.

Height - 87.0 cm.

Width-165.5cm and Depth-66.5 cm,

The product should be certified by UL GREENGUARD, SCS INDOOR ADVANTAGE GOLD.

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

174 NS- 107 Providing, supplying and placing of public seating. SEAT SHELL : The Seat is made from high density self- No's 1,10,794.95 2.00 2,21,589.90

skin Polyurethane foam reinforced with 1.2 mm M.S. perforated sheet insert. The Polyurethane foam

having density of min. 350 kg/m3 with a Shore 'A' hardness of 60±10.

SEAT SIZE : 52.0 cm (W) x 50.5 cm (D)

BACK SHELL : The Back is made from high density self-skin Polyurethane foam reinforced with 1.2 mm

M.S. perforated sheet insert.The Polyurethane Foam having density of min. 350 kg/m3 with a Shore 'A'

hardness of 60±10.

BACK SIZE : 52.0 cm (W) x 53.5 cm (H)

CROSS BEAM : Cross Beam made up of Diamond shaped double wall Extrusion of Aluminum 6063-T6

Alloy with coated of 50 micron epoxy polyester coating and fitted with Polypropylene Copolymer

engineering plastic end caps.

CROSS BEAM SIZE : 11.3 cm (W) x 9.4 cm (H) X 0.4 cm (Thickness).

LEG : Legs are made up of High pressure Aluminum ADC12 Die cast coated with 50 micron epoxy

polyester coating, Leg Are fitted with soft grip PVC level adjusting shoes.

ARMREST : Armrest are made up of High pressure Aluminum ADC12 die cast coated with 50 micron

epoxy polyester coating.

SEAT SUPPORT BRACKET Assembly : Seat support bracket assembly made up of argon shield welding of

Hot Rolled Steel (IS: 2062) 0.3cm Thickness. This welded structure is coated with 50 micron epoxy

polyester coating.

CLAMPING BRACKET : Clamping bracket are made up of Hot Rolled Steel (IS: 2062) 0.3cm Thickness

coated with 50 micron epoxy polyester coating.

Overall Dimensions of Chair

Seat Height - 42.5 cm.

Height - 87.0 cm.

Width-218.5cm and Depth-66.5 cm,

The product should be certified by UL GREENGUARD, SCS INDOOR ADVANTAGE GOLD.

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

175 NS- 108 Providing, suplying and placing of stoarge unit.Overall Dimensions of SD 2 Single Drive Cover Unit 2 No's 1,03,913.90 2.00 2,07,827.80

Bay(U/C + Fittings + Cover) shall be 2400mm(W) x 400mm(D) x 2113mm(H). The Construction shall be

rigid knock down made out of 0.8 thick CRCA steel conforming to IS:513, Gr.D. Each body shall have 1

main unit plus add on units (0,1,2,3 depending on no. of bays 1, 2, 3, 4 respectively) . Finish shall be

Epoxy polyester powder coated thickness of 40 microns . Shelf construction shall be with 12 bend panel

made from CRCA steel 0.7 mm thick IS:513, Gr.D .Uniformly distributed load capacity of 100 Kg .

Undercarriage shall have construction in welded frame made of HR sheet 3 mm thick conforming to IS :

2062. The Movements shall be Drive Type configuration : In case of D2,D3 & D4 movement of units is

achieved mechanically through a PU Hand Wheel and Sprocket-Chain arrangement mounted rigidly

onto body size. For D3 each movable undercarriage shall be provided with 3 driving rollers and 3 driven

rollers.LD understructure has 2 nos. of anti-tilt bearing assembly.The roller assembly comprises of a die-

cast step wheel, 2 deep-groove ball bearings and a MS shaft. The step wheel is made of cast steel and is

fitted onto the MS shaft using a feather key. The two ball bearings are then fastened on either side of

the step wheel using circlips. This entire roller assembly is then snap-fitted into a wheel housing. The

wheel housing is fixed in the U-channel of the understructure using machine screws. This wheel-

housing is made of engineering plastic material made by injection-molding process. The entire roller

assembly is designed to withstand the maximum loads of the body. Fittings shall be centralized locking

arrangement through Lock which is operated by spring mechanism mounted onto understructure of

last drive unit. The lock is made of 0.8 mm thick conforming to IS:513..The ‘sprocket-chain’

arrangement is covered by a 1 mm thk. CRCA sheet Drive Unit Cover with dimensions 1202mm x

398mm x 87mm and is fixed onto the side of the body. The PU handwheel is rigidly fixed at suitable

height on side of the body & projects out of cover by another 99.0 mm. Fixed unit (SD) does not have

the Drive Unit Cover. When the last Body is Twin Drive, i.e., TD, hinged doors are provided for the last

body. In this scenario the centralized locking system is fitted on the last TD body. Each Drive Type units

shall have Locking Knob near the drive wheel for manual locking of individual units when a person is

using those units. Knob shall be rotated to unlock position when units are to be moved. End stoppers

shall be provided to prevent derailment.The nuts & bolts are galvanized / blackodized / Zn Plated. Also

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

176 NS- 109 Providing, suplying and placing of stoarge unit.Overall Dimensions of LD 2 Single Drive Cover Unit 2 No's 1,79,390.40 2.00 3,58,780.80

Bay(U/C + Fittings + Cover) shall be 2400mm(W) x 400mm(D) x 2113mm(H). The Construction shall be

rigid knock down made out of 0.8 thick CRCA steel conforming to IS:513, Gr.D. Each body shall have 1

main unit plus add on units (0,1,2,3 depending on no. of bays 1, 2, 3, 4 respectively) . Finish shall be

Epoxy polyester powder coated thickness of 40 microns . Shelf construction shall be with 12 bend panel

made from CRCA steel 0.7 mm thick IS:513, Gr.D .Uniformly distributed load capacity of 100 Kg .

Undercarriage shall have construction in welded frame made of HR sheet 3 mm thick conforming to IS :

2062. The Movements shall be Drive Type configuration : In case of D2,D3 & D4 movement of units is

achieved mechanically through a PU Hand Wheel and Sprocket-Chain arrangement mounted rigidly

onto body size. For D3 each movable undercarriage shall be provided with 3 driving rollers and 3 driven

rollers.LD understructure has 2 nos. of anti-tilt bearing assembly.The roller assembly comprises of a die-

cast step wheel, 2 deep-groove ball bearings and a MS shaft. The step wheel is made of cast steel and is

fitted onto the MS shaft using a feather key. The two ball bearings are then fastened on either side of

the step wheel using circlips. This entire roller assembly is then snap-fitted into a wheel housing. The

wheel housing is fixed in the U-channel of the understructure using machine screws. This wheel-

housing is made of engineering plastic material made by injection-molding process. The entire roller

assembly is designed to withstand the maximum loads of the body. Fittings shall be centralized locking

arrangement through Lock which is operated by spring mechanism mounted onto understructure of

last drive unit. The lock is made of 0.8 mm thick conforming to IS:513..The ‘sprocket-chain’

arrangement is covered by a 1 mm thk. CRCA sheet Drive Unit Cover with dimensions 1202mm x

398mm x 87mm and is fixed onto the side of the body. The PU handwheel is rigidly fixed at suitable

height on side of the body & projects out of cover by another 99.0 mm. Last unit (LD) have the Drive

Unit Cover. When the last Body is Twin Drive, i.e., TD, hinged doors are provided for the last body. In

this scenario the centralized locking system is fitted on the last TD body. Each Drive Type units shall

have Locking Knob near the drive wheel for manual locking of individual units when a person is using

those units. Knob shall be rotated to unlock position when units are to be moved. End stoppers shall be

provided to prevent derailment.The nuts & bolts are galvanized / blackodized / Zn Plated. Also total

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

177 NS- 110 Providing, suplying and placing of stoarge unit.Overall Dimensions of TD 2 Single Drive Cover Unit 2 No's 2,28,308.05 8.00 18,26,464.40

Bay(U/C + Fittings + Cover) shall be 2400mm(W) x 800mm(D) x 2113mm(H). The Construction shall be

rigid knock down made out of 0.8 thick CRCA steel conforming to IS:513, Gr.D. Each body shall have 1

main unit plus add on units (0,1,2,3 depending on no. of bays 1, 2, 3, 4 respectively) . Finish shall be

Epoxy polyester powder coated thickness of 40 microns . Shelf construction shall be with 12 bend panel

made from CRCA steel 0.7 mm thick IS:513, Gr.D .Uniformly distributed load capacity of 100 Kg .

Undercarriage shall have construction in welded frame made of HR sheet 3 mm thick conforming to IS :

2062. The Movements shall be Drive Type configuration : In case of D2,D3 & D4 movement of units is

achieved mechanically through a PU Hand Wheel and Sprocket-Chain arrangement mounted rigidly

onto body size. For D3 each movable undercarriage shall be provided with 3 driving rollers and 3 driven

rollers.LD understructure has 2 nos. of anti-tilt bearing assembly.The roller assembly comprises of a die-

cast step wheel, 2 deep-groove ball bearings and a MS shaft. The step wheel is made of cast steel and is

fitted onto the MS shaft using a feather key. The two ball bearings are then fastened on either side of

the step wheel using circlips. This entire roller assembly is then snap-fitted into a wheel housing. The

wheel housing is fixed in the U-channel of the understructure using machine screws. This wheel-

housing is made of engineering plastic material made by injection-molding process. The entire roller

assembly is designed to withstand the maximum loads of the body. Fittings shall be centralized locking

arrangement through Lock which is operated by spring mechanism mounted onto understructure of

last drive unit. The lock is made of 0.8 mm thick conforming to IS:513..The ‘sprocket-chain’

arrangement is covered by a 1 mm thk. CRCA sheet Drive Unit Cover with dimensions 1202mm x

398mm x 87mm and is fixed onto the side of the body. The PU handwheel is rigidly fixed at suitable

height on side of the body & projects out of cover by another 99.0 mm. When the last Body is Twin

Drive, i.e., TD, hinged doors are provided for the last body. In this scenario the centralized locking

system is fitted on the last TD body. Each Drive Type units shall have Locking Knob near the drive wheel

for manual locking of individual units when a person is using those units. Knob shall be rotated to

unlock position when units are to be moved. End stoppers shall be provided to prevent derailment.The

178 NS- 111 nuts

Push galvanized / blackodized

/ D2 CHNL / ZnPlus

800mm -Optz Plated.

Pull total no. of 800mm-It

/ D2 CHNL loading levels per understructure

consists of ‘C’ section 2 No's 16,261.70 2.00 32,523.40

mm thk HR sheet & Square 25.4mm X 2mm thk ERW tube – both connected by screws. Prior to the

grouting of the guide channels with the help of raul plug & screw, ensure the ground is level. The rail

channels are of 3 lengths i.e., 800mm, 1600mm and 2400mm.

179 NS- 112 Optz Plus Push Pull / D2 CHNL 1600mm -It consists of ‘C’ section 2 mm thk HR sheet & Square 25.4mm No's 27,290.80 2.00 54,581.60

X 2mm thk ERW tube – both connected by screws. Prior to the grouting of the guide channels with the

help of raul plug & screw, ensure the ground is level. The rail channels are of 3 lengths i.e., 800mm,

1600mm and 2400mm.

180 NS- 113 Optz Plus Push Pull / D2 CHNL 2400mm-It consists of ‘C’ section 2 mm thk HR sheet & Square 25.4mm X No's 36,191.35 2.00 72,382.70

2mm thk ERW tube – both connected by screws. Prior to the grouting of the guide channels with the

help of raul plug & screw, ensure the ground is level. The rail channels are of 3 lengths i.e., 800mm,

1600mm and 2400mm.

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

181 NS- 114 FLIP NXT :-FLIP TBL MEM 1800W_750D FR OK-Providing, supplying and placing of Foldable, Stackable, No's 47,473.95 16.00 7,59,583.20

Cafeteria Tables.Overall Dimension - 1800 x 750 x 750 Table top should be made of 25min thk. MDF

OSR board (Bottom side in white color) as per IS:12406 with membrane finish on top side. Legs should

be made by welding the combination of MS ERW round Tube 063.5 x 2mm THK as per IS: 7138, flanges

made CRCA sheet of 1.6mm thk. and 1.2mm thk. as per IS 513 and inside plates made of HR 5mm thk.

sheet as per IS:2062. The Assembly will be epoxy polyester powder coated of minimum thickness 45

microns. The Table top will fold upside at offset center pivot provided on support bracket which should

be Aluminum alloy (ADC12) pressure die cast part coated with epoxy polyester powder coating of

minimum thickness of 45 microns. Table top connected with spring loaded mechanism with pull handle

made of MS ERW 016x1 2mm thk with an insert tube of 012.7x1.6mm thk tube as per IS:7138 coated

with epoxy polyester powder coated of minimum 45 micron thickness to operate table top. Legs should

be provided with casters of 065mm lockable type for ease of movement and can be locked when

required at any position.

182 NS- 115 Providing, supplying and placing of Café Chair. SHELL : The single piece seat back shell is made up of No's 7,884.90 109.00 8,59,454.10

injection moulded high impact strength glass filled polypropylene polymer compound (refer product

catalogue for colour chart).

SHELL SIZE : 44.0 cm. (W) x 50.2 cm. (D) x 40.5 cm. (H)

S.S. UNDERSTRUCTURE OPTION (SM6) : The tubular welded frame is made from Dia 2.22 ± 0.03cm x

0.15 ± 0.0128 cm Stainless Steel 304 grade tube which is buff polished. The 0.16 ± 0.008 cm thk

Stainless Steel 304 CRCA sheet is welded to tubes for fixing shell to the frame.The shoe is made of high

impact strength polypropylene polymer compound and are fitted at the end of the tubular frame.

WIDTH (W) : 51.5 CM

DEPTH (D) : 52.5 CM

HEIGHT (H) : 81.8 CM

SEAT HEIGHT (SH) : 45.9 CM.

The product should be certified by UL GREENGUARD, GRIHA, SCS INDOOR ADVANTAGE GOLD, BIFMA

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

184 NS- 117 Supplying and placing in position Main Table of the following specifications.2400 x 900 x 740 MAIN No's 2,29,055.10 - -

WORKTOP :Made of 43mm Thick (±1) combination of MDF and particle board with top veneer

facecoated with clear lacquer. All edges are edge banded with matching 1mm thick veneerlipping.

LEATHER PAD:Made of 18mm Thick (±1) MDF with Leatherette wrapped around top surface.

Thisleather pad is fixed to main top panel.

DRAWER UNIT:Top panel and drawer unit modesty panel is made of 43mm Thick (±1) combination

ofMDF and particle board with top veneer face coated with clear lacquer. All thicknessedges are edge

banded with matching lipping.

Remaining construction is of 18mm Pre-laminated twin board (PLT) of E1-P2 grade andapproved shade

confirming to IS-12823:1990, Edge banded with matching 2 mm thickPVC lipping. Bottom panel of

drawer is 9mm thick particle board with leatherette on topsurface.

Drawer unit is provided with soft closing channels for smooth opening and closing.Drawer unit is

secured with side central lock.

OPEN STORAGE UNIT:Top panel and open storage unit modesty panel is made of 43mm Thick (±1)

combination of MDF and particle board with top veneer face coated with clear lacquer. Allthickness

edges are edge banded with matching lipping.

Remaining construction is of 18mm Pre-laminated twin board (PLT) of E1-P2 grade andapproved shade

confirming to IS-12823:1990, Edge banded with matching 2 mm thickPVC lipping.

MODESTY:Made of 18mm Thick Pre-laminated twin board (PLT) of E1-P2 grade and approvedshade

confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVClipping. Modesty is fitted

with aluminum trims.

UNDERSTRUCTURE:Made of 18mm Thick Pre-laminated twin board (PLT) of E1-P2 grade and

approvedshade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVClipping. Door

is fixed with soft closing hinges and handle is provided for ease of opening.Also lock is provided on side

panel for security.

ACCESS FLAP WITH POWER BOX:Soft closing access flap with power box contains 3 Universal Sockets, 2

185 NS- 118 USB powerpoints,

Supplying 1 HDMI

and placing connection,

in position ERU of1 the

inbuilt misc. cable

following grommet and CAT

specifications.1200 3 and

x 610 6connections.

TOP PANEL:Made No's 64,101.60 - -

of 43mm Thick (±1) combination of MDF and particle board with top veneer facecoated with clear

lacquer. All edges are edge banded with matching 1mm thick venee rlipping.

UNDERSTRUCTURE:Made of 18mm Thick Pre-laminated twin board (PLT) of E1-P2 grade and approved

shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.

DOOR PANELS:Made of 18mm Thick Pre-laminated twin board (PLT) of E1-P2 grade and approved

shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVClipping. Door is fixed

with soft closing hinges and handle is provided for ease of opening.It is secured with side central lock.

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

186 NS- 119 Supplying and placing in position Back unit Body of the following specifications.2400 x 470 x 1226 No's 2,03,281.85 - -

CONSTRUCTION AND MATERIAL:Made from combination of side panel(0.5mm CRCA), Bottom

panel(0.5mm CRCA), Backpanel(0.5mm CRCA), Top Bottom stiffener(1.2mm CRCA) and End

Cover(0.6mm CRCA).Shelves are 12 bend panel made of 0.7mm Thick CRCA (D Grade, IS-513).

Storage body is powder coated with Epoxy Polyester to the thickness of 50 microns(+/-10 micron).

VENEER DOOR:Made of 12mm Thick (±1) MDF with 3.5mm veneer both side and face coated with

clearlacquer. All edges are edge banded with matching 1mm thick veneer lipping. Door isprovided with

soft closing hinge. Handle is also provided for ease of opening. Storage issecured with 3 way cam lock.

GLASS DOOR:Made from the combination of aluminium alloy (63400) extrusion and 4mm

cleartoughened glass. Aluminium extrusion of glass doors are powder coated with EpoxyPolyester to

the thickness of 50 microns (+/-10 micron). Handle is provided for ease ofopening. RH Glass Door is

provided with 3 way cam lock for security.

Supplying and placing in position Back unit Shutter of the following specifications.2400 x 470 x 1226

CONSTRUCTION AND MATERIAL:Made from combination of side panel(0.5mm CRCA), Bottom

panel(0.5mm CRCA), Backpanel(0.5mm CRCA), Top Bottom stiffener(1.2mm CRCA) and End

Cover(0.6mm CRCA).Shelves are 12 bend panel made of 0.7mm Thick CRCA (D Grade, IS-513).

Storage body is powder coated with Epoxy Polyester to the thickness of 50 microns(+/-10 micron).

VENEER DOOR:Made of 12mm Thick (±1) MDF with 3.5mm veneer both side and face coated with

clearlacquer. All edges are edge banded with matching 1mm thick veneer lipping. Door isprovided with

soft closing hinge. Handle is also provided for ease of opening. Storage issecured with 3 way cam lock.

GLASS DOOR:Made from the combination of aluminium alloy (63400) extrusion and 4mm

cleartoughened glass. Aluminium extrusion of glass doors are powder coated with EpoxyPolyester to

the thickness of 50 microns (+/-10 micron). Handle is provided for ease ofopening. RH Glass Door is

provided with 3 way cam lock for security.

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

187 NS- 120 Supplying and placing in position Main Table of the following specifications.3000 x 1050 x 740 MAIN No's 2,95,550.50 - -

WORKTOP :Made of 43mm Thick (±1) combination of MDF and particle board with top veneer

facecoated with clear lacquer. All edges are edge banded with matching 1mm thick veneerlipping.

LEATHER PAD:Made of 18mm Thick (±1) MDF with Leatherette wrapped around top surface.

Thisleather pad is fixed to main top panel.

DRAWER UNIT:Top panel and drawer unit modesty panel is made of 43mm Thick (±1) combination

ofMDF and particle board with top veneer face coated with clear lacquer. All thicknessedges are edge

banded with matching lipping.

Remaining construction is of 18mm Pre-laminated twin board (PLT) of E1-P2 grade andapproved shade

confirming to IS-12823:1990, Edge banded with matching 2 mm thickPVC lipping. Bottom panel of

drawer is 9mm thick particle board with leatherette on topsurface.

Drawer unit is provided with soft closing channels for smooth opening and closing.Drawer unit is

secured with side central lock.

OPEN STORAGE UNIT:Top panel and open storage unit modesty panel is made of 43mm Thick (±1)

combination of MDF and particle board with top veneer face coated with clear lacquer. Allthickness

edges are edge banded with matching lipping.

Remaining construction is of 18mm Pre-laminated twin board (PLT) of E1-P2 grade andapproved shade

confirming to IS-12823:1990, Edge banded with matching 2 mm thickPVC lipping.

MODESTY:Made of 18mm Thick Pre-laminated twin board (PLT) of E1-P2 grade and approvedshade

confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVClipping. Modesty is fitted

with aluminum trims.

UNDERSTRUCTURE:Made of 18mm Thick Pre-laminated twin board (PLT) of E1-P2 grade and

approvedshade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVClipping. Door

is fixed with soft closing hinges and handle is provided for ease of opening.Also lock is provided on side

panel for security.

ACCESS FLAP WITH POWER BOX:Soft closing access flap with power box contains 3 Universal Sockets, 2

188 NS- 121 USB powerpoints,

Supplying 1 HDMI

and placing connection,

in position ERU of1 the

inbuilt misc. cable

following grommet and CAT

specifications.1500 3 and

x 610 6connections.

TOP PANEL:Made No's 1,12,683.50 - -

of 43mm Thick (±1) combination of MDF and particle board with top veneer facecoated with clear

lacquer. All edges are edge banded with matching 1mm thick veneerlipping.

SLIDING SHUTTER:Made of 12mm Thick (±1) MDF with 3.5mm veneer both side and face coated with

clearlacquer. All thickness edges are edge banded with matching lipping.

Door is provided with soft closing & anti slam mechanism.

Handle is also provided for ease of opening. Storage is secured with lock.

UNDERSTRUCTURE:Made of 18mm Thick Pre-laminated twin board (PLT) of E1-P2 grade and

approvedshade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVClipping.

DRAWERS:Made of 18mm Thick Pre-laminated twin board (PLT) of E1-P2 grade and approvedshade

confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVClipping. Bottom panel of

drawer is 9mm thick particle board with leatherette on topsurface. Drawers have soft closing channels

for smooth opening and closing.

Digitally signed by VIVEK

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER AMOUNT AS PER

2023 CPWD DSR 2023 NON DSR ITEMS

189 NS- 122 Providing, supplying and placing of High Back Chair. SEAT ASSEMBLY: The Cushioned seat inner is made No's 1,33,138.60 - -