Annual operation, maintenance and providing civil and electrical maintenance (including facility management services) for office and residential complex at IWSS for 2 years

Item Description/ Heading

Supply of different type of Kaju clip 1" as required (50 pieces per packet)

Carriage of material by Mechanical Transport including loading, unloading and stacking Loose moorum/sand/earth/surkhi/cement/stone dust/hot mix asphalt, 2 km lead material.

Carriage of material by Mechanical Transport including loading, unloading and stacking Manure or sludge Lead - 1 km

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil.

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared.

Clearing grass and removal of the rubbish up to a distance of 50 m outside the periphery of the area cleared.

Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m. All kinds of soil

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Complete maintenance of the entire garden features having as per yard stick in the garden area i.e. lawn trees, shrubs, herbs, edge, flower beds, foliages, creepers etc. including hoeing,weeding, pruning, replacement of plants, gap filling, watering, mowing of lawn, grass cutting by lawn mover and brush cutter, removal of garden waste, applying insecticide, pesticide & fertilizers(whenever required) top dressing of lawn with good earth and manure and maintenance of other garden related works as directed by office-in-charge (Cost of Good Earth, Manure, Fertilizer, Insecticide, Pesticide will be provided by the Department & lawn mover and brush cutter with fuel and other T & P material/articles shall be provided by the contractor.) and as per direction of officer in charge.Play grounds / Public parks (1Mali for 2.00Acre).

Renovating lawns including weeding, cheeling the grass, forking the ground, top dressing with sludge or manure, mixing the same with forked soil, watering and maintaining the lawn for 30 days or more till the grass forms a thick lawn free from weeds and fit for mowing and disposal of rubbish as directed, including supplying good earth if needed (the cost of sludge, manure and the good earth shall be paid for separately).

Maintenance of potted plant Earthen pot in displayed at ground floor only in bungalow,office complex including application of good earth, manure, insecticide, pesticide and fertilizer, removing of dry parts by pruning, cleaning dry leaves and displaying in appropriate place and replacement of broken pots coloring of pots and change of location of pots and replacing with fresh plants as and when required ( Materials provided by the department) as per direction of officer in charge (For Earthen pot 750 Nos)

Maintenance of potted plants Cement pots at ground floor in flats and ground floor bungalow,office complex including application of good earth, manure, insecticide, pesticide and fertilizer, removing of dry parts by pruning, cleaning dry leaves and displaying in appropriate place and replacement of broken pots coloring of pots and change of location of pots and replacing with fresh plants as and when required ( Materials provided by the department) as per direction of officer in charge (For of Cement pots 300 no)

Complete maintenance of trees (Out side garden features), jobs like making of basin at regular interval i/c watering, weeding, pruning & application of fertilizer etc, (excluding the cost of material which shall be supplied by the department and other T & P material/articles shall be provided by the contractor) and as per direction of officer in charge.Trees for 1200 no (beyond 8 year Slow & beyond 6 Fast growing group)

Supplying and stacking of good earth at site including royalty and carriage upto 5 km lead complete (earth measured in stacks will be reduced by 20% for payment).

Supplying and stacking at site dump manure from approved source, including carriage upto 5 km lead complete (manure measured in stacks will be reduced by 8% for payment) :Screened through sieve of I.S. designation 20 mm

Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in-charge

Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately).

Providing and Displaying plants Budded Rose (H.T. variety) 3 to 4 healthy branch 30 cm and above ht. well developed with one and above flower plant in 20 cm Earthen Pot, as per direction of the officer-in-charge.

Providing and displaying of Areca Palm having ht. 90 cm to 1.20 m with 4 to 5 suckers, well developed, fresh and healthy with lush green foliage in 25 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.

Providing and displaying of Croton Duck foot (Elite) having ht. 45 cm and above with 3 to 4 branches, well developed, fresh and healthy leaves in 25 cm size of Earthen pot/Plastic pot. & as per direction of the officer-in-charge.

Providing and displaying of Phoenix palm having ht. 75 cm to 90 cm with 10 to 15 or more leaves, well developed, fresh and healthy in 25 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.

Providing Circular Cement Concrete pots of specified size, cast with cement concrete of nominal mix 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 6 mm nominal size), reinforced with 7 Nos ( 3 nos horizontal & 4 nos vertical “ U “ shape) M.S. wires of 3.5 mm dia as per design, including required form work, finishing with cement punning on exposed surface, curing for specified period and stacking in required rows & height, all complete as per direction of Officer-in-charge. Top inside dia 35 cm, outer bottom dia 25 cm, total height 35 cm with wall thickness of 25.4 mm

Providing and stacking of winter seasonal seedling/cutting at site of work well developed and healthy free from disease in per tray and each tray having 100 Nos plants as per direction of the officer-in-charge. Dahlia double

Providing and stacking of winter seasonal seedling/cutting at site of work well developed and healthy free from disease in per tray and each tray having 100 Nos plants as per direction of the officer-in-charge. Marigold French Hybrid dwarf

Providing and stacking of winter seasonal seedling/cutting at site of work well developed and healthy free from disease in per tray and each tray having 100 Nos plants as per direction of the officer-in-charge. Marigold Inca hybrid

Providing and stacking of winter seasonal seedling/cutting at site of work well developed and healthy free from disease in per tray and each tray having 100 Nos plants as per direction of the officer-in-charge. Pansy Hybrid

Providing and stacking of winter seasonal seedling/cutting at site of work well developed and healthy free from disease in per tray and each tray having 100 Nos plants as per direction of the officer-in-charge. Petunia hybrid

Providing and stacking of winter seasonal seedling/cutting at site of work well developed and healthy free from disease in per tray and each tray having 100 Nos plants as per direction of the officer-in-charge. Salvia

Providing and stacking of winter seasonal seedling/cutting at site of work well developed and healthy free from disease in per tray and each tray having 100 Nos plants as per direction of the officer-in-charge. Verbena hybrid

Providing and stacking of winter seasonal seedling/cutting at site of work well developed and healthy free from disease in per tray and each tray having 100 Nos plants as per direction of the officer-in-charge. Nemesia hybrid

Providing and stacking of winter seasonal seedling/cutting at site of work well developed and healthy free from disease in per tray and each tray having 100 Nos plants as per direction of the officer-in-charge. Poppy double

Providing and stacking of winter seasonal seedling/cutting at site of work well developed and healthy free from disease in per tray and each tray having 100 Nos plants as per direction of the officer-in-charge. Stock double

Providing and stacking of winter seasonal seedling/cutting at site of work well developed and healthy free from disease in per tray and each tray having 100 Nos plants as per direction of the officer-in-charge. Daisy hybrid

Providing and stacking of summer & rainy seasonal seedling at site of work well developed and healthy free from disease in per tray and each tray having 100 Nos plants as per direction of the officer-in-charge. Balsam seedling

Providing and stacking of summer & rainy seasonal seedling at site of work well developed and healthy free from disease in per tray and each tray having 100 Nos plants as per direction of the officer-in-charge. Celosia argentea & Celosia crostata Hybrid

Providing and stacking of summer & rainy seasonal seedling at site of work well developed and healthy free from disease in per tray and each tray having 100 Nos plants as per direction of the officer-in-charge. Gaillardia Double

Providing and stacking of summer & rainy seasonal seedling at site of work well developed and healthy free from disease in per tray and each tray having 100 Nos plants as per direction of the officer-in-charge. Gomphrena

Providing and stacking of summer & rainy seasonal seedling at site of work well developed and healthy free from disease in per tray and each tray having 100 Nos plants as per direction of the officer-in-charge. Kochia

Providing and stacking of summer & rainy seasonal seedling at site of work well developed and healthy free from disease in per tray and each tray having 100 Nos plants as per direction of the officer-in-charge. Cosmos hybrid

Providing and stacking of summer & rainy seasonal seedling at site of work well developed and healthy free from disease in per tray and each tray having 100 Nos plants as per direction of the officer-in-charge. Portulaca hybrid

Providing and stacking of summer & rainy seasonal seedling at site of work well developed and healthy free from disease in per tray and each tray having 100 Nos plants as per direction of the officer-in-charge. Sunflower Dwarf

Providing and stacking of summer & rainy seasonal seedling at site of work well developed and healthy free from disease in per tray and each tray having 100 Nos plants as per direction of the officer-in-charge. Vinca Hybrid

Providing and stacking of summer & rainy seasonal seedling at site of work well developed and healthy free from disease in per tray and each tray having 100 Nos plants as per direction of the officer-in-charge. Zinnia hybrid

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size).

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:3:6 (1 Cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 20 mm nominal size).

Providing, hoisting and fixing above plinth level up to floor five level precast reinforced cement concrete work in string courses, bands, copings, bed plates, anchor blocks, plain window sills and the like, including the cost of required centering, shuttering but, excluding cost of reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size).

Providing, hoisting and fixing above plinth level up to floor five level precast reinforced cement concrete in shelves, including setting in cement mortar 1:3 (1cement : 3 coarse sand), cost of required centering, shuttering and finishing with neat cement punning on exposed surfaces but , excluding the cost of reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size).

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.Cold twisted Bar

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & leng

th ( hold fast lugs or dash fastener shall be paid for separately).Sal wood

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick : Decorative plywood both side decorative veneer (Type - I) conforming to IS 1328 BWR type

Fly proof stainless steel grade 304 wire gauge with 0.5 mm dia. wire and 1.4 mm wide aperture with matching wood beading

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 25 mm thick (for cupboard) including ISI marked nickel plated bright finished M.S. piano hinges with necessary screws

Providing and fixing 18 mm thick, 150 mm wide pelmet of flat pressed 3 layer or graded wood particle board medium density grade I, IS : 3087 marked, including top cover of 6 mm commercial ply wood conforming to IS: 303 BWR grade, nickel plated M.S. pipe 20 mm dia ( heavy type) curtain rod with nickel plated brackets, including fixing with 25x3 mm M.S. flat 10 cm long fixed to pelmet with hollock wood cleats of size 100 mm x 40 mm x 40 mm on both inner side of pelmet and rawl plugs 75 mm long etc. all complete.

Extra for using veneered particle board conforming to IS 3097 Grade I, in item of pelmet 18mm thick 150mm wide. Particle board with decorative veneering on both sides

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).

Providing and fixing ISI marked oxidised M.S. pressed butt hinges with necessary screws etc. complete. 100x58x1.90 mm

Providing and fixing ISI marked oxidised M.S. pressed butt hinges with necessary screws etc. complete. 50x37x1.50 mm

Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete : 300x16 mm

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete :200x10 mm

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete :150x10 mm

Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete :125 mm

Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete : 100 mm

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. Twin rubber stopper

Providing and fixing factory made PVC Door shutter made of solid foam PVC profiles of thickness 5 mm and 15 mm at edges integrally extruded for vertical style and horizontal (top / bottom / lock) rails of minimum cross section of 70mm x 28mm, of shape and design as per manufacturer's specifications having homogenous fine cellular structure and smooth integral outer skin, inserted with G.I. 'C' section/rectangular tube profile of minimum 0.60 mm thickness with 120 gsm coating as stiffeners as per manufacturer's specifications Mitered cut joints for styles and rails provided with telescopic polymeric 'L' corners are joined together using solvent adhesive and strengthened with fully threaded stainless steel screws (of required size) through reinforcement stiffener with paneling of specified solid foam PVC board / high pressure laminate of required thickness and of approved design and shade (matching the styles and rails), secured within styles and rails with specially designed solid foam PVC moulded beadings of required size using PVC solvent adhesive / cement. The finished door shutter including SS hardware, 1 no. SS sliding door bolt 200 x 10mm, 1 no. SS tower bolt 200 x 10mm and 2 nos. SS handles 125 mm, shall be fixed to frame with 3 Nos. stainless steel hinges of minimum size 100x58x1.9mm and stainless steel screws of required size complete as per direction of the Engineer-in-Charge.(Cost of above hardware is inclusive in rates) 5 mm thick solid foam PVC panel of required size with moulded/extruded beading of appropriate design shape and size as per manufacturer's specifications (to secure the panel insert tight in place within the style and rails of the shutter)matching the color &shade of shutter frame.-Non decorative type.

Providing and fixing aluminum U beading of required size to Pre-laminated/ flush door shutter, including fixing etc. complete as per direction of Engineer-in-charge.

Providing and fixing wire gauge shutters using stainless steel grade 304 wire gauge with wire of dia 0.5 mm and average width of aperture 1.4 mm in both directions for doors, windows and clerestory windows with necessary screws : 30 mm thick shutters With ISI marked stainless steel butt hinges of required size Kiln seasoned and chemically treated hollock wood

Welding by gas or electric plant including transportation of plant at site etc. complete.

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing and fixing bolt including Nut and washer etc

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25

mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks)

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Bend 87.5°, 110 mm bend

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion ,Shoe (Plain) 110 mm Shoe

Providing and fixing M.S. holder bat clamps of approved design to C.I. or S.C.I. rain water pipes embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and cost of cutting holes and making good the walls etc. : 100 mm diameter

12 mm cement plaster of mix : 1:4 (1 cement: 4 fine sand)

12 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand)

Neat cement punning.

6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand)

Applying priming coat: With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood)

Fixing chowkhat in existing opening in brick/ RCC wall with dash fasteners/ Chemical fasteners of appropriate size (3 nos on each vertical member of door chowkhat and 2 nos on each vertical member of window chowkhats), including Cost of dash fasteners/ chemical fastener.

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq. meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per directions of Engineer-In-Charge. With cement mortar 1:4 (1 cement : 4 fine sand)

Renewing glass panes, with putty and nails wherever necessary including racking out the old putty: Float glass panes of thickness 4 mm (weight not less than 10kg/sqm)

Renewing glass panes, with putty and nails wherever necessary including racking out the old putty: Float glass panes of thickness 5mm (weight not less than 12.5kg/sqm)

Renewal of old putty of glass panes (length)

Distempering with 1st quality acrylic distember (Ready mix) having VOC content less than 50 grams/ litre of approved brand and manufacture to give an even shade : Old work (one or more coats)

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : One or more coats on old work

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : Of area 3 sq. metres and below

Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead : Of area 3 sq. metres and below

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.

Dismantling of flushing cistern of all types (C.I./PVC/Vitrious China) including stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead.

Dismantling C.I. or asbestos rain water pipe with fittings and clamps including stacking the material within 50 metres lead : 100 mm dia pipe

Dismantling of C.I. sluice valve including stacking of useful materials within a lead of 50 metres Up to 150 mm diameter

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Semi rigid pipe 32 mm dia

Providing and fixing white vitreous china water closet squatting pan (Indian type) : Orisa pattern W.C. pan of size 580x440 mm

Providing and fixing white vitreous china pedestal type (European type/ wash down type) water closet pan.

Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete. 10 litre capacity - White

Providing and fixing white vitreous china wash basin including making all connections but excluding the cost of fittings : Flat back wash basin of size 550x400 mm

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink with drain board 510x1040 mm bowl depth 250 mm

Providing and fixing 100 mm sand cast Iron grating for gully trap.

Providing and fixing soil, waste and vent pipes : 100 mm dia Sand cast iron S&S pipe as per IS: 1729

Providing and fixing solid plastic seat with lid for pedestal type W.C. pan complete : White solid plastic seat with lid

Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms

Providing and fixing brass bib cock of approved quality : 15 mm nominal bore

Providing and fixing brass stop cock of approved quality : 15 mm nominal bore

Providing and fixing brass stop cock of approved quality : 20 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 25 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 40 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 50 mm nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 15 mm nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 25 mm nominal bore

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet : 100 mm diameter

Providing and fixing uplasticised PVC connection pipe with brass unions :30 cm length 15 mm nominal bore

Providing and fixing PTMT bib cock of approved quality and colour. 15 m

m nominal bore, 122mm long, weighing not less than 99 gms

Providing and fixing PTMT pillar cock of approved quality and colour 15 mm nominal bore, 125 mm long foam flow, weighing not less than 120 gms

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. INTERNAL WORK - EXPOSED ON WALL 20 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. INTERNAL WORK - EXPOSED ON WALL 15 mm dia nominal bore

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber insertions etc. (the tail pieces if required will be paid separately) :100 mm diameter Class I

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 15 mm nominal bore

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 20 mm nominal bore

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 25 mm nominal bore

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. INTERNAL WORK - EXPOSED ON WALL 15 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. INTERNAL WORK - EXPOSED ON WALL 25 mm nominal outer dia Pipes

Dismantling of old S.W. pipes including breaking of joints and bed concrete stacking of useful materials near the site within 50 m lead and disposal of unserviceable materials into municipal dumps : 100 mm diameter

Dismantling of old S.W. pipes including breaking of joints and bed concrete stacking of useful materials near the site within 50 m lead and disposal of unserviceable materials into municipal dumps : 150 mm diameter

Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete : 100 mm diameter

Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete : 150 mm diameter

Supply of bleaching powder for drain side disinfection

Finishing walls with water proofing cement paint of required shade Old work (one or more coats applied @ 2.20 kg/10 sqm) over priming coat of primer applied @ 0.80 litrs/10 sqm complete including cost of Priming coat.

Manpower Deployment

Brick work with non modularFALG bricks conferming to IS:12894 class designation 7.5 average compressive strength etc in all respect in foundation and plinth :in Cement Mortar 1:6 (1 cement : 6 coarse sand).

Brick work with non modularFALG bricks conferming to IS:12894 class designation 7.5 average compressive strength etc in all respect in super structure above plinth level up to floor V level :in Cement mortar 1:6 (1 cement : 6 coarse sand)

Half brick masonry with non modular FALG bricks conferming to IS:12894, class designation7.5 Average compressive strength etc in all respect in foundation and plinth.In cement mortar 1:4 (1 cement: 4 coarse sand)

Part A (Non DSR ITEMS)

Cleaning of surface drain including disposal of muck/sludge through trolly or other arrangement to a specified place( in no case it shall be kept on drain banks ) within a lead of 1KM complete with all tools & tackles as per instruction of EIC up to 300mm wide -

Cleaning of surface drain including disposal of muck/sludge through trolly or other arrangement to a specified place( in no case it shall be kept on drain banks ) within a lead of 1KM complete with all tools & tackles as per instruction of EIC Above 300mm & up to 600mm wide

Cleaning of surface drain including disposal of muck/sludge through trolly or other arrangement to a specified place( in no case it shall be kept on drain banks ) within a lead of 1KM complete with all tools & tackles as per instruction of EIC Above 600mm wide

Brooming & cleaning of all roads in colony and with in the premises of service buildings and other places as required with all tools & tackles and stacking the garbage at specified place as per instruction of EIC .

Cleaning of all type of roof including removal of dry leaves, weedings and clearing drain holes, brooming etc all complete with all tools & tackles and stacking the garbage at specified place as per instruction of EIC

Cleaning of toilet (floor area up to 10sqm) including cleaning of dado, skirting, WC pan ( Indian type/ Western type), wash basin, urinals, glass shelves, mirror and other fittings, if any for 'D' type or equivelent qtr including any other wash basin out side the toilet by hand dusting and cleaning with soap solution, acids,deodrents, phenyl etc to make the toilet clean and hygienic all complete with tools, tackles & consumables as per instruction of EIC. Freq-Weekly

Cleaning of toilet (floor area up to 8sqm) including cleaning of dado, skirting, WC pan ( Indian type/ Western type), wash basin, urinals, glass shelves, mirror and other fittings, if any for 'C' type or equivelent qtr including any other wash basin out side the toilet by hand dusting and cleaning with soap solution, acids,deodrents, phenyl etc to make the toilet clean and hygienic all complete with tools, tackles & consumables as per instruction of EIC.Freq-Weekly

Cleaning of toilet including WC pan, wash basin, other fittings, if any for 'B' & lower type qtr by hand dusting and cleaning with soap solution, acids, phenyl etc to make the toilet clean and hygienic all complete with tools, tackles & consumables as per instruction of EIC.Freq-Weekly

Collection of garbage from door to door and disposal of the same through trolly or other suitable arrangement to the specified place with in a lead of 1KM including sweeping of stair case ( for 1st and 2nd floor qtrs) with all tools and tackles complete as per instruction of EIC Ground floor

Collection of garbage from door to door and disposal of the same through trolly or other suitable arrangement to the specified place with in a lead of 1KM including sweeping of stair case ( for ist and 2nd floor qtrs) with all tools and tackles complete as per instruction of EIC First floor

Disposal of dead animal including transportation to the specified place, making earth pit, disposal of dead animal into pit with adequate quantity of salt, lime and bleaching powder etc and reffiling the pit with earth all complete with tools, tackles and consumable as per instruction of EIC Big animal (cow,buffalo,Ox and the like)

Disposal of dead animal including transportation to the specified place, making earth pit, disposal of dead animal into pit with adequate quantity of salt, lime and bleaching powder etc and reffiling the pit with earth all complete with tools, tackles and consumable as per instruction of EIC Small animal(Dog,Cat,fox,pig,birds and the like)

Cleaning of toilet attached with hostel rooms, office chambers etc. including cleaning of floors, skirting and dado, WC pan ( Indian type/ Western type), wash basin, shelves, mirror and other fittings, if any by hand dusting and cleaning with soap solution, aci

ds,deodrents, phenyl etc to make the toilet clean and hygienic and providing naphthalene balls in urinals complete with all tools, tackles & consumables as per instruction of EIC ( for community & service buildings) . Freq- Daily

Cleaning of general/ common toilet including cleaning of WC pan ( Indian type/ Western type), wash basin, urinals by hand dusting and cleaning with soap solution, acids,deodrents, phenyl etc to make the toilet clean and hygienic including providing naphthalene balls in urinals etc complete with all tools, tackles & consumables as per instruction of EIC . Freq- Daily

Cleaning of inspection chamber of all sizes and disposal of sludge etc at specified place outside the colony with all leads including removal & replacing of top cover , mending the damages of cover and chamber , if any, etc as per instruction of EIC

Cleaning of chocked sewer line & sludge line of all diameter including removal of earth, opening of joints , cleaning of pipe line , making joints leak proof etc all complete including disposal of sludge materials outside the colony with all leads at specified place with tools & tackles as per instruction of EIC

Cleaning of septic tank of 20 users with tools & tackles including disposal of sludge material outside the periphery of colony with all leads at specified place complete as per instruction of EIC

Cleaning of door shutters,window shutters including chowkhats, window grills, glass panes,cobwebs etc of service / community buildings with necessary detergents, chemicals etc complete as per instruction of EIC

Cleaning of sludge line & traps (kitchen & toilet) of all diameter at different floors including opening of joints, cleaning of pipe line and again jointing and flushing with fresh water all complete with tools & tackles as per instruction of EIC

Cleaning ,moping & washing of floor of public buildings other places neatly with detergent/ bleaching powder etc all complete with tools & tackles and consumable to make the floor clean & hygienic as per instruction of EIC

Cleaning of ground reservoir including scraping of stains and muck from wall and floor and removal of muck from reservoir, disinfecting the tank by lime/ bleaching powder etc and washing the tank with fresh water , writing the cleaning date with paint on the outer surface of the tank all complete with tools & tackles and consumable as per instruction of EIC

Cleaning ,sweeping & brushing of Alum/ Lime tanks including internal and external drains ,cleaning,removal and disposal of sludge and garbage etc all complete as per instruction of EIC.

Cleaning of sludge & mud between filter beds to airiator including drains, partition, outside area of plant as per instruction of EIC.

Trimming of tree branches in colony/ plant & near boundry wall including disposal of branches outside the periphry of the colony & plant area as per instruction of EIC area

Daily Operation of all valves for two years at IWSS residential colony and WTP/ administrative building all complete as per instruction of Engr I/Charge. (Deduction will be made at double rate for non-deployment of required manpower or for less engagement of manpower on prorita basis)

Supply of cistern parts & misc itemsPVC ball (Float ball for low level cistern)

Bib cock pillar cock washer

Syphon for low level cistern

Syphon washer for cistern

Handle & lever for low level cisterm

Jumpeer washer

Steel jali 100mm dia

PVC Tank Cover

Cleaning of roof top water tank including draiming out water, cleaning, dis-infecting the tank by bleaching powder etc and washing the tank with fresh water writing of cleaning date with paint on outer face of the tank all complete with tools & tacles and consumbles as per instruction of Engr I/C . Freq- Once in Four Months.

Supply of M-Seal

Providing GI Socket 15 mm dia

supply of G.I. socket , 20mm

supply of G.I. socket , 25mm

supply of G.I. socket , 40mm

Supply of GI Flange 50mm dia

Supply of GI Flange 80mm dia

Supply of GI Flange 100mm dia

Supply of CI sluice valve 50mm dia

Supply of CI sluice valve 80mnm dia

Supply of GI Tee 25mnm dia

Supply of GI Tee 50mnm dia

Supply of GI Bend 50mnm dia

Supply of GI Bend 80mnm dia

Supply of GI Bend 100mnm dia

supply of G.I. Nipple15mm dia

supply of G.I. Nipple 20mm dia

Supply of GI Nipple 25mnm dia

Supply of GI Nipple 40mnm dia

Supply of GI Nipple 80 mm dia

Supply of GI Nipple 50mnm dia

GI Plug 15mm

GI Plug 20mm

GI Plug 25mm

providing / supplying of flush door shutters 18 mm thick block board with commercial ply

supply of commercial ply ply wood 5 ply with commercial ply on both faces 6mm thick

supply of commercial ply 12 mm commercial ply

kitchen sink coupling (waste ) 32mm

stainless steel flower pots or plant (410mm dia & 410 mm height )

Supplying of insecticides/ Fungicides, Pesticides and fertilizers from authorised dealers at site as per instruction of Engineer-in-charge. DAP

Supplying of insecticides/ Fungicides, Pesticides and fertilizers from authorised dealers at site as per instruction of Engineer-in-charge. Bone meal

Supplying of insecticides/ Fungicides, Pesticides and fertilizers from authorised dealers at site as per instruction of Engineer-in-charge. Urea

Supplying of insecticides/ Fungicides, Pesticides and fertilizers from authorised dealers at site as per instruction of Engineer-in-charge. NPK 12:32:6

Supplying of insecticides/ Fungicides, Pesticides and fertilizers from authorised dealers at site as per instruction of Engineer-in-charge. Super Phosphate

Supplying of insecticides/ Fungicides, Pesticides and fertilizers from authorised dealers at site as per instruction of Engineer-in-charge. Neem Cake

Supplying of insecticides/ Fungicides, Pesticides and fertilizers from authorised dealers at site as per instruction of Engineer-in-charge. Melathian

Supplying of insecticides/ Fungicides, Pesticides and fertilizers from authorised dealers at site as per instruction of Engineer-in-charge.Rogar 30%

Supplying of insecticides/ Fungicides, Pesticides and fertilizers from authorised dealers at site as per instruction of Engineer-in-charge. Sarso Khalli

Supplying of insecticides/ Fungicides, Pesticides and fertilizers from authorised dealers at site as per instruction of Engineer-in-charge. Indo Cell

ACs and Water Coolers Maintenance

Per Gram

Supplying at site good quality pots Earthen Pots of 12" size

Supply of good quality of seeds of flower (Ordinary)

Supply of good quality of seeds of flower (Hybrid)

Petty carpentary repair works such as repairing of cupboard, nails screw fixing hinges tightening of doors and windows shutter etc. as & when required as per instruction of EIC.

Anti Adult Measures-General disinfection/pest control with a new generation odourless, colourless insecticides which should be safe for human being and effective for all kind of household insects like mosquitos, housefliesetc.Using residual spray of Deltamethrin in 2.5% SC fLOW (K Othrine or approved equivalent).Insecticides should be sprayed uniformly over the surfaces of wall,ceiling,etc.Frequency -once in 3 month. (Area 35630X4=142520)

Anti Adult Measures-General disinfection/pest control with a new generation odourless,colourless insecticides which should be safe for human being and effective for all kind of household insects like mosquitos,housefliesetc.Using residual spray of Cyfluthrin 5% EW(Solfac EW O5O or approved equivalent).Insecticides should be sprayed uniformly over the surfaces of wall,ceiling,etc.Frequency -once in 3 month (Area 35630X4=142520)

Thermal fogging-Using insecticide Deltamethrin 1.25% ULV (Kingfog or approved equivalent) mixed with diesel into the ratio of 1:199 for outdoor operation of colony etc. Frequency-Monthly.(29985 X 24 = 720000)

Anti Larvae Measures-Treatment by using Diflubenzuron 25% WP(Bi-Larv or approved equivalent) solution should be spread as per instructionofEIC.Frequency-Weekly (3250 X 104 week = 338000)

Providng and fixing hand shower (health faucet) with 8 mm dia. 1.20 metre long flexible tube and wall hook of Jaguar make or equivalent.(ALD-CHR-573) as per instruction of EIC.

smantling tile work in floors and roofs laid in cement mortar including stackingmaterial within 50 metres lead. For thickness of tiles 10 mm to 25 mm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete. Size of Tile 600x600 mm

Providing and laying Vitrified tiles in floor with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately). Size of Tile 600x600 mm

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work 15 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work 20 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work 25 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work 40 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work 50 mm dia nominal bore

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer- in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape whereverrequired.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups,including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Granite stone slab colour black, Cherry/Ruby red Area of slab over 0.50 sqm

Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material with in 50 meters lead as directed by Engineer-in-charge.

Dismantling W.C. Pan of all sizes including disposal of dismantled materials i/c malba all complete as per directions of Engineer-in- Charge.

Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within 50 metres lead of: G.S. Sheet

Lettering with black Japan paint of approved brand and manufacture per letter per cm height 3.5

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete. each 873.55

Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer's specification. per 50kg cement

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 250x16 mm

Supply of 2+6 way way, SPN, single door, MCB DB

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 200x10 mm each

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 100x10 mm each

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 125 mm

each job

Per 100 Sqm

per letter per cm height

per 50kg cement

Part B Pest Control (Non DSR Items)

Complete overhauling, greasing of ceiling fan including dismantling, transportation and reinstallation: Material Cost

Complete overhauling ,greasing of ceiling fan including dismantling, transportation and reinstallation: Labour Cost

Complete rewinding of ceiling fan including transporting ,dismantling,bearing replacement assembly and commissioning of same :Material Cost

Complete rewinding of ceiling fan including transporting , dismantling,bearing replacement assembly and commissioning of same: L

abour Cost

Complete rewinding of different type exhaust fan ( including dismantling, assembling and commissioning of the same): Material Cost

Complete rewinding of different type exhaust fan ( including dismantling, assembling and commissioning of the same): Labour Cost

Supply of ceiling fan clamp with rubber / metallic shaft for ceiling fan of standard make with replacement of old material

Supply of different type of ceiling fan and exhaust fan bearing such as 6201, 6202, 6203 as required

Supply of different type of ceiling fan and exhaust fan capacitor of 2.5 mF as required

Board Related Material

Supply of Modular GI Box - 2 Module

Fixing of electrical consumable items in residential quarters (MQ type, A, B, C, and D -types; Kota BPH, Kakari BPH and CWPH Plant in IWSS) and overhead line and pole works by engaging 02 personnel consisting of 02 nos. skilled electrician per day for 730 days to attend the daily complaints and routine works as required at IWSS Premises

Supply of Modular GI Box - 4 Module

Supply of Modular GI Box - 8 Module

Supply of Modular GI Box - 12 Module

Supply of Modular Base and Cover Plate - 2 Module

Supply of Modular Base and Cover Plate - 4 Module

Supply of Modular Base and Cover Plate - 8 Module

Switches, Sockets, Casings & Cappings, Conduits, etc

Supply of one-way 5/6A Modular switch

Supply of 15/16A Modular switch

Supply of 3-Pin 5/6A Modular socket

Supply of 6-Pin 15/16A Modular socket

Supply of Modular Bell switch, ISI marked

Supply of Modular fan regulator

Supply of 20 mm iron staples/saddles/screws

Supply of 25 mm iron staples/saddles/screws

Supply of 20 mm dia, ISI marked, PVC conduit

Supply of 25 mm dia, ISI marked, PVC conduit

Supply of 20 mm PVC bends

Supply of Supply of 25 mm PVC bends

Day to day maintenance of window/split AC ( 1.5 Ton) with the help of 1 Skilled , 1 semiskilled and 1 Unskilled labour

A. 33kV/6.6 kV/415V OHL Works

Supply of20 mm PVC couplers

Supply of 25 mm PVC couplers

Supply of 20 mm PVC junction box, two way

Supply of Brass bracket holder 16 mm

Supply of PVC Batten/Angle Holder

Supply of 30 A, TPN, industrial type socket outlet, with plug top and metal chained cover in sheet steel enclosure

Supply of Aluminium lugs for 10 sq. mm cable

Supply of Cu lugs for 16 sq. mm cable

Supply of Aluminium lugs for 25 sq. mm cable

Supply of Cu lugs for 35 sq. mm cable

Supply of Cu lugs for 50 sq. mm cable

Supply of Cu lugs for 70 sq. mm cable

Supply of Cu lugs for 95 sq. mm cable

Supply of Cu lugs for 120 sq. mm cable

Erection of steel material such as MS channel bracket, angle, clamp, support plate, pipe, nut & bolt etc.

Line Guarding with brackets

Supply of different type of exhaust fan blade as required

Repairing of poles (angle cutting and welding in the base of poles for strengthening)

Supply of Cu lugs for 150 sq. mm cable

Supply of TAPE;ADHSV,PVC;19MMX25MX0.125MM

Supply of TAPE;MICANITE,19MMX50M

Supply of TAPE;BTMN PVC,3/4INX25/50MX19MM,HT

Supply of different type steel Nails as required

Supply of different type steel screw as required (1000 pieces per packet)

Rewinding of different type motor AC /water cooler with Replacement of bush /shaft etc. as required

Replacement of capacitor,4mf+-5% 440 volt AC 50 HZ 20c TO 80c As per IS2993 make Phillips, Crompton capital or equivalent

Replacement of capacitor,45mf+-5% 440 volt AC 50 HZ 20c TO 80c As per IS2993 make Phillips, Crompton capital or equivalent

Replacement of water cooler fan blade suitable for different types.

Replacement of AC fan blade suitable for different types.

Control relay suitable for split AC having 2 No & 2NC and 220 volt holding coil

Filter with strainer, artichoke for different types of window/split AC.

Capillary for different types of window/split AC

PCB 1.5 Ton Invertor AC Indoor

PCB 1.5 Ton Invertor AC Outdoor

AC Blower Indoor 1.5 Ton

Split AC 1.5 Ton/2 Ton Display

Condensor coil 1.5 Ton copper Split AC

Refilling R410/R32 gases

Different type of screw suitable for fixing in equipment

E&M PART

Fan Related Works

PVC Pipe ½” dia .

Inverter AC 1.5Ton compressor

Remote 1.5 Ton Invertor

Watercooler Compressor

Copper pipe 1/4,3/8 and 5/8

Insulation cover 1/4,3/8 and 5/8

Dismantling of following:-

11-16m long tubular/rail pole

Earth Wire size 7/14 SWG

ACSR Wolf/Raccoon or equivalent conductor

11kV Disc insulator with hardware

11 kV grade pin insulator with pin

33kV pin insulator with pin

Stay set with stay wire, stay clamp and stay insulator

Danger board with clamp, bracket and nut bolts

Steel material such as MS channel bracket, angle, clamp, support, plate, pipe, nut & bolt, etc.

Erection

Survey pegging/jungle cleaning including tree branch cutting and removing it ouside away from OHL for taking alignment of overhead line and its maintenance

Erection of steel tubular pole/rail pole exceeding 11m but not exceeding 16m in brick blast/local hard stone with concreting of cement, mine gravel

Excavation for stay pit & refilling in all kind of soil including soft rock

Concreting of stay pit with cement, mine gravel, and local sand in the ratio 1:4:8

Erection of 11kV grade disc insulator with hardware

Erection of 11kV grade pin insulator with pin

Erection of 33kV pin insulator with GI pin

Erection of stay set complete including binding, tensioning with 7/10 SWG stay wire and stay insulator with back clamp on pole

Laying, stringing, tensioning of ACSR Wolf, Raccoon or equivalent conductor

Laying, stringing and tensioning of 7/14 SWG GI earth wire

Fabrication of steel material such as: MS channel, bracket, angle clamp, support plate etc. (steel material,welding rod, gas are departmently provided and other things such as welding m/c, cutting set etc are provided by contractor)

Safety, Protection, Maintenance

Installation/fixing of lighting arrestor complete with earthing strip etc.

Providing and fixing guarding on the line including fixing of brackets as per requirement

Opening the jumper and rejumpering (three nos. in one set)

Erection of danger boards with bracket and fasteners on required height of HT poles, switches and isolators

Installation/fixing of anticlimbing device or barbed wire by wounding on required height on the poles

Concreting for old pole including muffing with cement, mine gravel and local sand in poles having muff size dia. 30cm, height 75 cm

Painting of poles and brackets (HT and LT street light) with supply of paint (one coat primer and two coat aluminium paint)

Supply Part

MS bolt nut washer of various sizes 5/8x2", 5/8x4" long as required

GI Earth wire 7/14 SWG wire

Total impact of GST for the purpose of CTC