SPECIAL REPAIR TO BLDG NO. P-1288 (KONARK AUDITORIUM) IN ARMY AREA JODHPUR UNDER GE (ARMY) NO. 02 JODHPUR

Amount

Demolition of stone masonry of any description and in any position, built in cement mortar, including all quoins, arches and pillars etc., complete all as specified and directed.

M&L for squared rubble walling Jodhpur type brought unto course well bonded, bedded and solidly hearted built in cement mortar 1:6., complete all as specified and directed.

M&L for squared rubble walling Jodhpur type brought unto course well bonded, bedded and solidly hearted built in cement mortar 1:6 but except stone complete all as specified and directed.

Extra over of hammer dressing to face stone with maximum depression on face from straight edge not exceeding 20mm and dressing face, bed and joints to squared rubble walling jodhpur type brought unto courses complete all as specified and directed.

Racking out joints/pointing to square rubble masonry Jodhpur type regular coursed built in cement mortar complete all as specified and directed.

M&L for keyed pointing in CM 1:4 to squared rubble masonry Jodhpur type brought unto courses complete all as specified and directed.

M&L for 15 mm thick rendering in cement mortar on fair faces of stone masonry surfaces or surface other than fair face of brick-work surfaces, applied in two layers ie., Ist layer of 10 mm thick rendering in cement mortar 1:6 and 2nd ( top ) layer of 5 mm thick rendering in cement mortar 1:4 and top layer mixed with water proofing compound as per manufacturer's instruction & finished even and smooth without using extra cement including taking down existing cement plaster of any description and in any position and racking out joints, hacking for key, scrubbing down with water etc & prepared to receive new plaster complete all as specified and directed. (Note:- Water proofing compound shall be measured and paid separately under appropriate item of Sch 'A' as "supply only")

Supply only water proofing compound complete all as specified and directed.

M&L for preparing of plastered or unplastered surfaces & finished walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade on new walls (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified and directed.

Demolition of Concrete in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) etc. complete all as specified and directed.

M&L for 75 mm thick PCC 1:4:8, type D2, using 40mm graded stone aggregate as in sub base for flooring complete all as specified and directed.

M&L for 60 mm thick, machine made, 1st quality, precast cement concrete rubber moulded coloured interlocking paver blocks/tiles, of triangular/Zigzag/Hexagonal in shape or shape and design as approved, with grey cement and pigment, having crushing strength not less than 300 Kg/Sqcm and conforming to IS specifications, laid over and including a layer of 25mm thick sand cushion including filling the joints with sand as in floors/paths/pavings etc, complete all as specified and directed.

M&L for factory made precast machine pressed kerb stones of PCC 1:2:4, Type B1, using 20 mm graded stone aggregate and of shape and size as directed, set jointed and pointed cement and sand mortar 1:4 fixed in repairs with and including necessary excavation and earth work and making good the disturb surfaces to match with the existing surfaces including removal and disposal of rubbish complete all as specified and directed.

M&L for 50mm thick PCC 1:3:6, type C2, using 20mm graded stone aggregate as in plinth protection, finishing the surface even and smooth without using extra cement including forming & filling expansion joints 50mm deep 10mm wide filled with sealing compound graded A complete all as specified and directed.

Dismantling floor, hearth or wall tiling of any description and in any position including cement mortar bedding (but not backing) complete all as specified and directed.

M&L for non skid ceramic tiles, joint free, coloured tiles 7mm to 8mm thick (Square or rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tile laid over and including 15 mm thick screed bed or bedding layer of cement mortar 1:6 as in floors etc., complete all as specified and directed.

Dismantling water tanks of any description in any position exceeding 500 but not exceeding 1000 lit capacity complete all as specified and directed.

S&F Rotational moulded polyethylene triple layered water storage tanks (cylindrical vertical with closed top) 1000 litres capacity, white in colour hoisted and fixed in position with and including all fittings and fixtures complete all as specified and directed.

S&F 20mm ball valves high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed/fixed to pipes/ferrules complete all as specified and directed.

Taking down existing chowkats or frames of any description and in any position exceeding 1.50 sqm but not exceeding 4 sqm each with shutter (without taking off shutter from the frames) complete all as specified and directed.

Taking down existing chowkats or frames of any description and in any position not exceeding 1.50 sqm each with shutter (without taking off shutter from the frames) complete all as specified and directed.

M&L for 2nd class hard wood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and directed.

S&F 100 mm brass door handle mortice lock, 4 levers vertical type complete all as specified and directed.

M&L for complete removal of existing treatment of walls, providing and applying plaster of paris putty of 1 mm thickness over plastered surface to prepare the surface even and smooth complete all as specified and directed.

M&L for applying two or more coats of distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification and directed.

Dismantling of cast iron or reinforced concrete or PVC drain pipes, jointed in cement mortar and taking out of trenches, if required, including all fittings, heads, shoes, bends, swan necks, etc., (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed.

S&F 200 mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints required, including all fittings, heads, shoes, bends, swan necks, etc., fixed on walls including MS clamps all as required complete all as specified and directed

M&L for PCC 1:2:4, Type B1, using 12.5mm graded stone aggregate as in copings, water troughs and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and directed

Dismantling plain or corrugated steel sheeting, any gauge of any description and in any position as in roof coverings including connected ridge complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coated GI based corrugated steel sheet 0.5mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coated GI based corrugated steel sheet 0.5mm thick of any colour and including 50mm thick EPS coating, having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping complete all as specified and directed.

Refixing of pre-painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.5mm thick of any colour and including 50mm thick EPS coating (having tensile strength of 550 Mpa) as in roof covering/cladding to wall, fixed with self tapping complete all as specified and directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc. complete all as specified and directed.

S&F MS work in roof trusses (framed), trussed, rails and fastenings and heavy bracket, framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc with Fe 410 -W(Gde- E- 250) quality- A complete all as specified and directed.

M&L for preparation of new steel and iron surface of any description and in any position over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide complete all as specified and directed by Engr-in-Charge.

Demolition of cement concrete (unreinforced) of any description and in any position, not otherwise specifically provided for as in roof treatment etc., complete all as specified and directed.

Taking down of existing damaged / loosened cement concrete/ brick tiles from roof / terrace to a depth of average 50 mm including taking down of existing APP membrane if any, cleaning with water and depositing of debris to a distance not exceeding 50m complete all as specified and as directed by Engineer-in-Charge

M&L for rendering 15mm thick, cement mortar 1:4 mixed with WPC @3% by weight of cement at green concrete complete all as specified and as directed. Note: WPC shall be measured and paid separately.

M&L for APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyester non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application over a coat of approved bitumnen primer @0.40 liter per Sqm complete all as specified and directed.

M&L for PCC 1:2:4, Type B1, using 20mm graded stone aggregate average 40mm thick in padding over APP membrane sheet, including making panels of size not exceeding 0.40 sqm and filling grooves with sealing compound grade 'A' complete all as specified and directed.

Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and directed.

M&L for post construction Anti termite treatment in voids in masonry using chemical emulsion one litre per hole, at 300mm intervals including drilling holes at 45 degree and replugging them with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floors complete all as specified and directed.

M&L for 8 mm thick, Non asbestos fibre cement building boards fixed or laid/ inserted to timber/GI/Aluminium framework with screws complete all as specified and directed.

M&L for refixing of 8 mm thick Non asbestos fibre cement building boards fixed or laid/ inserted to timber/GI/Aluminium framework with screws complete all as specified & directed.

M&L for preparation of new or old surfaces of insulation/Non asbestos fibre cement building boards and applying two coats of sound absorption paint over a coat of base coat by spray painting complete all as specified & directed.

M&L for Gl frame work for seamless ceiling comprising of Gl perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/ intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx. 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exceeding 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre with Hangers 6 mm dia. GI. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and directed

M&L for 12mm thick perforated particle board/ tiles for insulation and acoustic purposes, 60x60 cm in size, fixed in ceiling in GI frame work or with staples on snap grid complete all as specified and directed.

Taking down carefully cement concrete spelled out concrete from RCC roof projections, ceilings, sunsheds, beams, walls etc upto cover depth by chipping out lightly including necessary scaffolding etc., complete all as specified and directed.

S&F MS wire mesh of 1mm dia wire and 25 mm mesh size fixed with nails and screws around RCC chajjas/fascia etc., complete all as specified and directed.

M&L for single component polymer modified repair mortar with compressive strength of minimum 38 Mpa at 28 gays (ASTM C 109:99) and tensile strength of minimum 2.5 Mpa (ASTM C 307) upto 15mm in a single coat @ 34 Kg per Sqm for 15mm thickness as per manufacturer instructions complete all as specified and directed.

S&F in repair 50 mm thick Jodhpur stone jalli of design as approved by GE, fixed with CM 1:4 complete all as specified and directed.

S&F in repair Jodhpur stone pillar of design as approved by GE, fixed with CM 1:4 complete all as specified and directed.

M&L for 1.25 mm thick mild steel plain black sheet for rain water gutter water troughs; ducts; etc. cut to size edges beaded if directed, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel members, etc., with plain 40 mm lap joints or welded/ riveted seams including bending, turning up, mitred angles, stopped ends, outlets, etc. as required complete all as specified & directed.

M&L for taking out fixed auditorium chair, repair and complete servicing of auditorium chair, including repair & replacement of necessary parts i.e spring, back cover, handle, hand rest, foam cushion seat & seat cover if required, foundation bolts etc if required, oiling/greasing complete to make chair smooth functioning and complete change of fabrics of chair of approved quality & colour complete all as specified and directed.

Labour only for fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement (Except material)

S&F 60 mm thick factory made Flush shutters, solid core construction with block board core and plywood and both faces are covered with decorative face veneer with lipping/frame to match complete all as specified and directed.

S&F 12 mm thick WPC boards with both side laminated, for wall panelling of approved colour, fixed with screws to frame work complete all as specified and directed.

Dismantling boarding, any description, fixed in any position with nails complete all as specified and directed.

S&F 12mm thick plywood, grade BWP, type BB fixed with screws to timber frame work complete all as specified and directed.

S&F 0.9mm thick decorative laminate type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instructions complete all as specified and directed.

S&F cover fillets of tempered hard board, 40mm wide and fixing with screws complete all as specified and directed.

S&F 12mm thick toughened glass as in hinged doors, partitions automatic doors and similar work including cutting to shape, drilling holes required complete all as specified and directed.

S&F Continuous (piano type) hinges of 30mm wide flaps, mild steel, bright finish or electro galvanised complete all as specified and directed.

S&F 50mm dia, polished, hardwood knobs fixed with screws complete all as specified and directed.

S&F 65mm mortise lock, brass 4 levers, vertical type complete all as specified and directed.

S&F 75mm extruded brass handles, fabricated type polished complete all as specified and directed.

S&F 5mm thick coloured acrylic sheet fixed with screws to timber frame work complete all as specified and directed.

Supply only Granite (of any type or of any colour) work (table rubbed and polished) cills, platforms complete all as specified and directed

S&F 2nd class hardwood for Transoms or mullions, straight, for solid frames of any description, wrought, framed, double rebated on the solid, rounded or chamfered (including weathering to transom, if required put together with glue, pinned at joints), complete all as specified and directed.

M&L for french polishing on surfaces of any description, width or girth including cleaning and preparing the surface including a coat of wood filler on new works with two or more coats complete all as specified and directed.

S&F stainless steel magnetic door catcher suitable for cupboards complete all as specified and directed.

Taking down carefully point wiring from existing place (light/fan, socket or power points complete) with all fittings such as switches, sockets ceiling rose, pendant holder, fitting and fixtures, MCB DB’s, MCB, Main switches, call bell etc and making good to disturbed surface to wall, floor etc., to match with existing surface either by using same colour distemper or white colour wash complete all as required and directed.

Taking down carefully by unscrewing from boards outlet boxes, fittings and fixtures such as Tube light fittings of any type complete all as directed. Note:- This item to be operated only when item found serviceable for reuse in work.

M&L for point wiring with FRLS PVC insulated and unsheathed stranded copper conductor cable of size 1.5 sqmm, 1100V drawn in and including non metalic PVC conduit of size 20 mm dia, medium grade and PVC conduit fittings including FRLS PVC insulated and unsheathed solid copper earth wire of size 1.5 sqmm connecting to common earth dolly with and including CI//pressed steel terminal box 1.2mm thick of required size, 3mm thick bakelite sheet for mounting switches, sockets, brass screws and washers complete all as directed for the following:-

(a) One light / fan point controlled by one way switch.

(b) One 3 pin 5 Amp socket on the same board

(c) One 3 pin 5 Amp socket on independent board.

(d) One 3 pin 15/16 Amp socket independent but with 2.5 sqmm mm PVC insulated unsheathed copper stranded conductor and 1.5 Sqmm mm size PVC insulated solid copper conductor as earth continuity conductor.

(e) One bell point controlled by one push bottom switch.

(f) One light point controlled by, 2- way switch

Refixing only any type of Tube light fittings obtained from Item No. 73 above, including making connection to ceiling rose/connector with copper flexible cable of size 1.5 sqmm complete all as specified and directed.

S&F in replacement modular ceiling rose surface backelite, 65x20mm, three terminal complete all as specified and directed.

S&F in replacement of modular switch, 1 way, 6 Amp, 1 module, 240 V, flush type complete all as specified and directed.

S&F in replacement of modular switch, 1 way, 16 Amp, 1 module, 240 V, flush type complete all as specified and directed.

S&F in replacement of modular bell push, flush type, 6 Amp, 1 module, 240 V complete all as specified and directed.

S&F in replacement of modular socket, 6A, 2/3 pin combined, 2 module, 240 V complete all as specified and directed.

S&F in replacement of modular socket, 6/16Amp, 2/3 pin combined, 2 module, 240 V complete all as specified and directed.

S&F in replacement of modular fan step regulator, 120 W, 2 module, 240 V complete all as specified and directed.

S&F in replacement of modular white cover plate with frame, 3 module, including box complete all as specified and directed.

S&F in replacement of modular white cover plate with frame, 4 module, including box complete all as specified and directed.

S&F in replacement of modular white cover plate with frame, 6 module, including box complete all as specified and directed.

S&F in replacement of modular white cover plate with frame, 8 module, including box complete all as specified and directed.

S&F in replacement of modular switch, 2 way, 6 Amp, 1 module, 240 V, flush type complete all as specified and directed.

S&F in replacement of modular blank plate with frame and suitable module complete all as specified and directed.

S&F in replacement of sheet metal enclosure for MCB DB SPN, 8 way, double door type with 200 Amps rated Bus bar suitable for SPN MCB incoming including suitable size of plyboard for fixing of DB complete all as specified and directed.

All as in item No 89 above but for SPN, 12 way, 240 Volts

S&F in replacement MCB, SPN, 40 to 63 Amp, 240 Volt, 'C' curve complete all as specified and directed.

S&F in replacement MCB, SP, upto 40 Amp, 240 Volt, 'C' curve complete all as specified and directed.

S&F in replacement MCB, SP, 6 to 32 Amp, 240 Volt, 'C' curve complete all as specified and directed.

S&F in replacement of capacitor 2.5/3.15/4.0 MFD, 240 volts suitable for ceiling fan/ wall mounted fan 1200/1400 mm sweep type complete all as specified and directed.

S&F LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

M&L for sub main wiring with two runs of 4 Sqmm (nominal area), single core PVC insulated and unsheathed multi stranded copper conductor cable, LT 1100 grade, FRLS cable drawn in PVC conduit with all necessary fittings and accessories and run of PVC insulated and unsheathed single core cable with copper conductor of size 4.0 Sqmm as earth wire (green in colour ) run through PVC rigid conduit and connected to common earth dolly, including taking out the old sub main wiring complete all as specified and directed. Note:-Two run of cable and one run of PVC conduit and one run of earth continuity wire shall be measured as one run.

All as per item No. 96 hereinbefore but two runs of 2.5 Sqmm, single core with PVC FRLS insulated and unsheathed stranded copper conductor cable of size 2.5 Sqmm as earth lead complete all as specified and directed.

All as per item No. 96 hereinbefore but two runs of 6 Sqmm, single core with PVC FRLS insulated and unsheathed stranded copper conductor cable of size 6 Sqmm as earth lead complete as specified and directed.

M&L for Earthing complete with galvanised steel earth plate electrode 60×60cm.× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion including provision of 20mm bore, light grade GI pipe up to 7.5m length as protection to earth lead wire and 20mm bore medium grade GI pipe with funnel and wire mesh for watering connected to earth test point including excavation, earth work in any type of soil, PCC 1:3:6, type C1 pit with RCC cover including charcoal, salt, funnel complete all as specified and directed. Note:- Rate included for excavation & earth work in any type of strata as shown in electric plate No-3 in SSR Part I.

Ditto as per item no 99 but using galvanised iron strip 25×4mm as earthing lead, 32 mm dia GI Medium grade protection pipe.

S&F in replacement industrial type metal clad plug top & socket, single pole and a natural link earth enclosure with MCB, SP, 20 Amp complete all as specified and directed

M&L in repair of wall mounted fan of any sweep including rewinding and including fixing/ replacement of spare arrangements with complete greasing and cleaning of the fan and refixing it back from the removed location complete all as specified and directed.

S&F in repair one bakelite sheet not less than 3 mm thick after removing all connection including cutting/chasing to accommodate existing fitment and making connection including cadmium plated screws with cup washer complete all as specified and directed.

S&F Air circulator fans, 230 volts, single phase, oscillating type, 400/450 mm sweep suitable for wall mounting complete all as specified and directed.

S&F LED tube lights fitting with high out put diffuser, 4 feet, 1x 20W, 220V, AC with driver and LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

S&F LED luminaire 600x600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for false ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed

S&F round shape 6 watt, 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

S&F round shape 15 watt, 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

S&F in replacement of LED luminaire 36/40 Watt, 230 volts 50 HZ mounted with diffuser size '1x4' approx. with accessories and connecting complete all as specified and directed by Engr-in-Charge.

S&F exhaust fan 250mm sweep, 230V, 50Hz, 1200 RPM, Copper winded, made of sturdy engineering plastic complete with louvers shutter complete all as specified and directed.

M&L for repair of unserviceable hand dryer by removing the cover, carefully clean dust and lint by using brush or vacuum and replace faulty controller lens or as required at site etc., complete all as specified and directed.

Taking down unserviceable aluminium strip of any size from any location with complete unserviceable fittings complete all as directed

S&F aluminium strip 25x3 mm with saddles and fixing screws etc., for roof conductors and down conductors above ground surface for lightning conductors complete all as specified and directed by Engr-in-Charge.

M&L for test point terminal block made of gun metal or phosphorous bronze of size 75x75x25 mm drilled and screwed including 3 Nos, 8 mm dia, 25 mm long hexagonal head screw including taking down old one complete all as directed.

Labour for refix the same serviceable aluminium strip taking down from item No 112 hereinbefore after straightening by pulling with new saddles and refixing with screws etc., for roof conductors and down conductors above ground surface for lightning conductors complete all as specified and directed by Engr-in-Charge.

S&F in replacement LED aviation obstruction light fitting, 12/10 watt as per existing with all accessories, bracket for fixing arrangement including taking down old unserviceable one complete all as directed by Engineer-in-Charge

M&L for opening round hole on brick/stone/PCC block wall for exhaust fan 250 mm sweep mounting, plaster and finishing with colour as matching with existing surface & colour and grout bolts/fastener etc. at any height of bldgs complete all as specified and directed.

M&L for 4mm dia GI or steel wire earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc., complete all as specified and directed.

S&F LED premium model step lighting system with up down arrow with illuminated seat and row number on both sides in front of step complete with LED solid core optical fiber aluminium extraction housing, anti skid profile etc., length of each upto one meter or as per required at site complete all as specified and directed.

S&F 12 volt, 15 amp, SMPS power supply for step lighting system as required at site complete all specified and directed.

S&F 12 volt, Laser engraved chair indicator plate marked as required at site complete all specified and directed.

M&L for sub main wiring with 2 run of 1.5 Sqmm FRLS, PVC insulated, unsheathed and stranded copper conductor cable with and including 1.5 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable as earth wire connected with thimble from main DB, drawn in to existing concealed as required on site, including all accessories with and including cutting chasing and making good of disturbed surface of wall/floor/ceiling etc as required on site by brick/concrete work, plastering, white washing, OBD etc., as required complete all as specified and directed. Note:- Two run of 1.5 Sqmm and one run of 1.5 Sqmm earth wire cable will be measured as one length including making good the disturbed surfaces etc., all as required on site.

M&L for taking down LED light fitting step lights of 2 watt with integral driver, with all accessories and refixing the same by making all necessary electric connection to fittings complete all as required, specified and directed at site.

S&F decorative LED pendant type light fitting with lamp for snacks/bar counter in auditorium 15 watt, with integral driver including hanging arrangement in ceiling complete with all accessories and making necessary electric connection complete all as specified and directed.

M&L for three way motorised direct mounted actuator valve complete set 3"/2" with all accessories and including piping arrangement, providing connections etc complete as specified and directed by EIC. Note : cost of welding work for connection and disconnection of valve and pipeline, cost of MS pipe heavy duty of size 3"/2.5"/4" upto 3 mtrs pieces is deemed to be included in quoted rates.

(a) 80 mm dia (3")

(b) 50 mm dia (2")

Supplying, laying/fixing, testing and commissioning of following nominal sizes of chilled water piping plumbing confirming to IS- 1239 Part-1 with necessary clamps, vibration isolators fittings with all fittings such as tees bends etc but excluding valves, strainers, gauges etc., complete all as specified and as directed:- Note:- (i) The piping shall be duly insulated with fire retardant quality XLPE insulation of thickness 13 mm after applying rubber based adhesive. (CPRX compound). (ii) Insulated pipe shall be covered with 0.63mm aluminium sheet cladding complete with type 3, grade 1 roofing felt strip (as per IS:1322 as amended upto date) all as directed by Engineer in charge

(a) 80 mm dia.

(b) 50 mm dia

Supplying, fixing, testing and commissioning of insulated butterfly valve (Manual) with CI body, SS Disc, Nitrile Rubber Seal & O-ring, PN 1.0 pressure rating for chilled water/hot water circulation, strainers, gauges in the Chilled Water/Condenser Water/ plumbing duly insulated to the same specifications as the connected piping and adequately supported complete all as specified and as directed.

(a) 80mm dia.

(b) 50 mm dia

M&L for providing and fixing in position the industrial type pressure gauge complete all as specified and as directed.

M&L for providing and fixing in position the mercury in glass, industrial type thermometer complete as required and as directed.

Supply, installation, testing and commissioning of 12 mm/20mm dia auto air vent valve complete all as specified and as directed.

Supply, install and commissioning of GSS square/rectangular ducting complete all as per site requirement and as directed for the following thick:- Note : Dimension of the return air duct/supply duct shall be as per existing duct designed dimension

(a) 22 gauge (0.8mm) thick

(b) 20 gauge (1.0 mm) thick

Supplying, Fixing and Commissioning of fire dampers in supply air duct/main branch and return air path as and where required of required sizes i/c control wiring, the damper shall be motorized and spring return so as to close the damper in the event of power failure automatically and open the same in case of power being restored. The spring return action shall be inbuilt mechanism and not externally mounted. The damper shall also be closed in the event of fire signal complete as required and dimensions shall be taken as per existing sample all as per directions of engineer-in-charge

M&L for provisioning acoustic lining of insulation to main supply air duct from AHU upto length of 6mtr with Resin bonded fiber glass of 25mm to 30mm thick of density 48Kg/cum covered with 28G Aluminium perforated sheet all as directed by Engineer-in-Charge

M&L for provision of air duct XLPE insulation thickness 13mm with factory backed aluminum foil and including the following:- (a) M&L for cleaning the duct surface (to be insulated) by scrapping carefully with wire brush etc., to make the surface completely free of millscale, dirt, dust, grease and other foreign material, taking special care so that all duct joints are sealed against any leakages. (b) M&L for applying rubber based adhesive CPRX compound onto duct surface. Note: Quoted rate shall include cleaning of duct and adhesive

S&F Rotational moulded polyethylene water storage tank three layers of capacity 2000 ltr (cylindrical vertical with closed top) hoisted duly insulated with 13mm thick XLPE insulated backed with aluminium foil and fixed in position all as specified and directed. Note: Pipe fittings to chilled water piping from tank upto 10 meter along with plumbing, welding, PCC work shall be included in the quoted rate.

Supply, laying and testing cable XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty), 1100 Volts grade with stranded copper conductor of size 16 sqmm mm 4 core laid in trenches, floors, pipes or fixed in walls complete all as specified and as directed.

Dismantling of existing PCC tank and disposing of the scrap up to distance of 500mtr, repairing the existing foundation, disconnecting of chilled/hot water piping, supply air duct, return air duct, PCC type water storage tank and all the related connecting items complete all as directed by Engineer-in charge.

M&L for provision of 0.63mm thick aluminuim cladding to insulated air duct all as directed by Engineer-in-charge

M&L for sealing of AHU roof with gap/crack filler or rubber gasket all as per existing sample for 4 Nos of AHU and sealing of gap between GSS duct sheet and wall at duct entrance and exist complete all as directed by Engineer-in-Charge

Labour only for removing existing broken insulation on chilled water piping and cleaning the duct surface (to be insulated) by scrapping carefully with wire brush etc., to make the surface completely free of millscale, dirt, dust, grease and other foreign material, taking special care so that all duct joints are sealed against any leakages complete all as directed.

M&L for insulation of Chilled water piping with 13mm thick water proof XLPE insulation complete all as specified and as directed. Note:- (i) The piping shall be duly insulated with 13mm thick fire retardant quality XLPE insulation after applying rubber based adhesive(CPRX compound). (ii) Insulated pipe shall be covered with 0.63mm aluminium sheet cladding complete with type3, grade 1 roofing felt strip (as per IS:1322 as amended upto date) all as directed by Engineer in charge.

S & F of double canvas cloth connected for AHUS with flang, nut, bolt, gasket etc. All as per direction of Engineer-in-Charge.

M/S KAUTILYA GARG

RISING ELECTRICALS

Anil Builders

SANJOLI CONSTRUCTION COMPANY