Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | 1₹34.6 LAccepted-Finance | 1 | Accepted-Finance Lowest Bid | |
| 2 | 2₹40.6 L+₹6.0 L (17.3%)Rejected-Finance HIMACHAL PRADESH | MANDI | HIMACHAL PRADESH | 175013 | 2 | Rejected-Finance Bid rejected being higher | |
| 3 | Rejected-Technical VILL MANOH P O BASSI TEH JOGINDER NAGAR DISTT MANDI H P | JOGINDER NAGAR | MANDI | HIMACHAL PRADESH | - | Rejected-Technical Documents not submitted physically | |
| 4 | Rejected-Technical | - | Rejected-Technical Documents not submitted physically |
Tender Value
Refer Docs
EMD Value
₹1.2 L
Closing Date
21 Dec 2022, 4:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
Divisional Forest Officer Renuka Ji
Divisional Forest Officer Renuka Ji
Construction of additional two sets in inspection hut at Forest Complex Renuka Ji
2022_FD_66775_1
Fts.1652-515/2022-23(Bud.)
Open Tender
Civil Works - Buildings
Item Rate
275 days
O/O Divisional Forest Officer Renuka Ji
8 documents required · 8 mandatory
₹1,500
Payable To O/O DFO Renuka Ji
₹1.2 L
22 Dec 2022
13 Dec 2022
22 Dec 2022
13 Dec 2022
21 Dec 2022
13 Dec 2022
13 Dec 2022 - 21 Dec 2022
Amount
EARTH WORK
Earth work in excavation by mechanical means ( Hydraulic excavator)/manual means over areas( exceeding 30 cm in depth/1.5m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50m and lift upto 1.5m,as directed by engineer in charge.All kinds of soil
Excavation trenches of required width for pipes,cables etc including excavattion for sockets,and dressing of sides, ramming of bottom,depth upto 1.5m, including getting out the excavated soil,and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited laye by ramming,watering,ect. and disposing of surplusexcavated soil as directed, with in a lead of 50 m: All kinds of soil pipes,cables etc, not exceeding 80mm dia.
Supplying and filling in plinth with sand under floors, including ,watering,ramming,consolidating and dressing complete.
Providing and lying in position cement concrete of specified grade excluding the cost of centering and shuttering -All work upto plinth level 1:4:8(1 cement:4 coarse sand ): 8 graded stone aggregate 40mm nominal size.
Reinforced cement concrete work in beams,suspended floors,roofs having slope up to 15 ͦ landing ,balconies ,shelves,chajjas, lintels,bends plain window sills,staircases and sprial stair cases above plinth level upto floor five level,excluding the cost of centering ,shuttering finishing and reinforcement with1:1.5:3(1 cement:1.5 coarse sand:3 graded stone aggregate 20mm nominal size.)
FORM WORK : Centering and shuttering including strutting, propping etc. and removal of form for : Suspended floors,roofs,landings, balconies and access platform.
FORM WORK : Centering and shuttering including strutting, propping etc. and removal of form for : lintels,beams,plinth beams,priders,bressumers and cantilevers.
FORM WORK : Centering and shuttering including strutting, propping etc. and removal of form for :Edges of slabs and breaks in floors and walls under 20 cm wid.
Steel reinforcement for RCC work including straightening,cutting ,bending ,placing in position and binding all complete upto plinth level mild steel and medium tensile steel bars.
Brick work with common burnt clay F.P.S (non modular) bricks of class designation 7.5 in foundation and plinth in : Cement mortar 1:6 ( 1 cement : 6 coarse sand)
Brick work with common burnt clay F.P.S (Non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V Level in all shapes and size in 1:6(1 cement: 6 coarse sand)
Half bricks masonry with common burnt clay F.P.S (Non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V Level. Cement mortar 1:4(1 cement: 4 coarse sand)
Providing wood work in frames of doors, winddows,clerestory window and other fames,wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length hold fast lugs or dash fastners shall be paid for seprately second class teak wood.
Providing and fixing panelled or panelled and glazed shutters for doors,windows and clerestory window fixing with butt hinges of required size with necessary screw, excluding panelling which will be paid for separately, all complete as per direction of engineer in charge 35mm thick shutters second class teak wood
Provoding and fixing panelling or panelling and glazing in panelled or panelled and gllazed shutters for doors,window and clerestory window ( Area of opening for panel inserts excluding portion inside grooves or rebates to be measured) panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick: Plain particle board flat pressed 3 layer or graded wood particle board medium density grade -I IS 3087 Marked.
Providing and fixing wire guage Shutters using galvanized M.S wire guage of average iwdth of aperture 1.4mm in both direction with wire of dia 0.63mm,for doors ,windows and clerestory windows with hinges and necessory screw :35 mm thick shutters with ISI marked M.S pressed butt hinges bright finished of required size second class teak wood.
Providing and fixing chromium plated brass curtain rod having wall thiknesss of 1.23mm with two chromium plated brass brackets fixed with C.P Brass screw and PVC sleeves etc. wherever necessary complete 20mm dia.
Providing and fixing of MS grill of required pattern in frames of window etc. with M.S flats, square or round bars etc. including priming coat with approved steel primer all complete fixed to opening/wooden frames with rawl plugs screws etc.
Providing and fixing of aluminium sliding door bolts,ISI marked anodised (Anodic coating not less than grade AC 10 as per IS 1868),transparent or dyed to required colour or shade, with nuts and screw etc. complete 300x16mm.
Providing and fixing aluminium sliding doors bolts, ISI marked anodised ( anodic coating not les than grade AC 10 as per IS 1868) transparent or dyed to required colour or shade, with necessary screw ect. Complete : 250x16mm
Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) ransparent or dyed to required colour or shade, with necessary screw ect. Complete : 300X10mm
Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) ransparent or dyed to required colour or shade, with necessary screw ect. Complete :150x10mm
Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) ransparent or dyed to required colour or shade, with necessary screw ect. Complete :125 mm
Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) ransparent or dyed to required colour or shade, with necessary screw ect. Complete :100 mm
Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) ransparent or dyed to required colour or shade, with necessary screw ect. Complete Twin rubber stopper
Providing and fixing aluminium casement stays ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) ransparent or dyed to required colour or shade, with necessary screw ect. Complete.
Steel work in built up tubular ( round,square or rectangular hollow tubes etc.) tresses etc. including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete hot finished weldd type tubes.
Providing and fixing M.S fan clamp type I or II of 16 mm dia. M.S. bar,bent to shape with hooked ends in RCC slabs of beams during lying, including painting the exposed portion of loop ,all as per standered design complete
Cement concerete flooring 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floting coat of neat cement, including slurry,but excluding the cost of nosing of steps etc. complete 40mm thick with 20 mm nominal size stone.
Providing and lying vitrified tiles in different sizes (thikness to be specified by the manufactured ) with water absorption less than 0.08% and conforming to IS:15622, of approved beand & manufacturer, in all colours and shade ,laid on 20 mm thick cement mortar 1:4( 1 cement : 4 coarse sand),jointing with grey cement slurry @ 3.3 kg/sqm including grouting the joint with white cement and matching pigment etc. complete size of tile 600mmx600mm
Providing and lying vitrified tiles in different sizes (thikness to be specified by the manufactured ) with water absorption less than 0.08% and conforming to IS:15622, of approved beand & manufacturer, in all colours and shade , in skirting ,riser if steps, laid with cement based higher polymer modified quick set tile adhesive ( water based) conforming to IS:15477 in average 6mm thickenss including grouting of joints(payment for grouting of joints to be made separately) size of tiles 500x50mm
Providing and laying polished granite stone flooring in required design and patterns ,in linear as well as curvilinear portion of the building all complete as per the architectural drawing with 18mm thick stone slab over 20 mm(average) thick base of cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing,curing and polishing etc. all complete as per specified and as directed by the Engineer in charge. polished granite stone slab jet black ,cherry, red,Elite brown, cat eye or equivalent.
Extra for providing and fixing wind ties of 40x6mm flat iron section.
Providing and fixing on wall face unplasticised rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382,leaving 10mm gap for thermal expension ,(i) single socketed pipes. 110mm diameter.
Providing and fixing on wall face unplasticised PVC moduled fittings.accessories for unplasticiesd rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382,leaving 10mm gap for thermal expension. Coupler 110mm
Providing and fixing on wall face unplasticised PVC moduled fittings.accessories for unplasticiesd rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382,leaving 10mm gap for thermal expension. 110mm bend
Providing and fixing on wall face unplasticised PVC moduled fittings.accessories for unplasticiesd rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382,leaving 10mm gap for thermal expension. 110mm shoe
Providing and fixing unplasticised-PVC pipe clips of approved design to unplasticised PVC- rain water pipes by means of 50x50x50 mm hard wood pligs,screwed with MS screw of required length, including cutting brick work and fixing in cement mortar 1:4 ( 1 cement: 4 coarse sand) and making good the wall etc. complete 110mm
Providing and fixing precoated galvanised iron profile sheets(size, shape and pitch of corrugation as approved by Engineer -in charge 0.50 mm(+0.05%) total coated thickness with zinc coating 120 grama per sqm as per IS :277,in 240 mpa steel grade,5-7 microns epoxy primer on both side of the sheet and polyster top coat 15-18 microns.Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and sould be supplied in single length upto 12 meter or as desired by Engineer-in-charge.The Sheet shall be fixed using self drilling/self tapping screws of size(5.5x55mm) with EPDM seal, complete upto any pitch in horizontal/vertical or curved surface, excluding the cost of purlins,rafters and trusses and including cutting to size and shape wherever required.
Providing and fixing precoated galvanised steel sheet roofing accessories0.50mm(+0.05%) total coated thickness,zinc coating 120 grams as per sqm as per IS:277, in 240 mpa steel grade,5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/self tapping screws complete ridges plain (500-600mm)
Providing and fixing precoated galvanised steel sheet roofing accessories0.50mm(+0.05%) total coated thickness,zinc coating 120 grams as per sqm as per IS:277, in 240 mpa steel grade,5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/self tapping screws complete flashings/ aprons (upto 600mm)
Providing and fixing precoated galvanised steel sheet roofing accessories0.50mm(+0.05%) total coated thickness,zinc coating 120 grams as per sqm as per IS:277, in 240 mpa steel grade,5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/self tapping screws complete gutter 12.51.6 (600mm over all girth)
SUB HEAD: CONSTRUCTION OF FINISHING WORK
15MM cement plaster on the rough side of single or halfbrick wall of mix 1:6(1 cement: 6 fine sand)
6mm cement plaster of mix 1:3 ( 1cement:3fine sand)
Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete
Finishing walls with water proofing cement paint of required shade New work(Two or more coats applied @3.84kg/10sqm
Finishing walls with 100% premium arylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, alkali & fungal resistance ,dirt resistance exterior paint of required shade ( company depot Tinted) with silicon additives. New work ( Two or more coats applied@ 1.43 litre/10sqm. Over and including priming coat of exterior primer applied@ 0.90 litre/10 sqm
Painting wood work with Deluxe multi surface paint of required shade.Two or more coat applied @ 0.90ltr/10sqm over an under coat of primer applied @ 0.75 ltr/10 sqm of approved brand and manufacture
Painting wood work with Deluxe multi surface paint of required shade.Two or more coat applied @ 0.90ltr/10sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture
Applying priming coat with ready mixed pink or gray primer of approved brand and manufacture on wood work ( hard and soft wood)
WATER SUPPLY AND SANITARY INSTALLATION
Providing and fixing one piece construction white vitreous china squatting plate with an integral longitudinal flushing pipe,white P.V.C automatic flushing cistern,wit fittings,standerd size G.I/PVC flush pipe for back and front flush with standard spreader pipes with fittings,GI Clamps and CP brass coupling complete, including painting of fittings and cutting and making good the walls and floors etc. wherever required :- Single squatting plate with 5 liter PVC automatic flushing cistern.
Providing and fixing wash basin with C.I brackets, 15mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fitting and brackets, cutting and making good the walls wherever required :- (a) white Vitreous China wash basin size 550x400mm with a 15mm CP Brass single hole basin mixer
Providing and fixnig stainless steel A ISI 304 (18/8) Kitchen sink as per IS 13983 with C.I brackets and stainless steel plug 40mm, including painting of fittings and brackets, cutting and making good the walls wherever required 510x1040mm bowl depth 225
Provindig and fixing of 8 mm dia C.P/S.S Jet with flexible tube upto 1 meter long with S.S tringular plate to european type W.C of quality and make as approved by engineer-in -charge.
Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C waste fittings complete 32mm dia.
Providing and fixing 600x450mm size bavelled edge mirrore of superior glass ( of approved quality) complete with 6mm thick hard board ground fixed to wooden cleats with C.P. brass screw and washers complete.
Providing and fixing 600x120x5mm glass shelf witth edges round off,supported on anodised aluminium angle frame with C.P.Brass bracktes and guard rail complete fixed with 40 mm log screwa,rawl plugs etc. complete
Providing and fixing soil,waste and vent pipes : 100 mm dia.
Providing and fixing PTMT liquid soap container 109mm wide,125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour,weighing not less than 105 gms
Providing and fixing water closet squatting pan ( Indian ackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour,600 mm long towel rail with total length of 645 mm, width78mm and effective height of 88 mm weighting not less than 190 gms.
Providing and fixing toilet paper holder : CP: brass
Providing and fixing G.I Pipes complete with G.I. Fittings and clamps, I/C cutting and making good the walls etc. 15mm dia nominal bore. ( Internal)
Providing and fixing G.I Pipes complete with G.I. Fittings and clamps, I/C cutting and making good the walls etc. 25mm dia nominal bore. ( External)
Making Connection of G.I distribution branch with G.I main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete :25 to 40 mm nominal bore
Providing and fixing brass stop cock of approved quality with 15 mm nominal bore
Providing and fixing brass stop cock of approved quality with 20 mm nominal bore
Providing and fixing gun metal gate valve with C.I. Wheel of approved quality (Screw end) : 25mm nominal bore
Providing and fixing unplasticised PVC connection pipe with brass union : 30 cms length 15mm nominal bore
Providing and fixing C.P brass shower rose with 15 or 20 mm inlet 100mm diameter
Constructing masonry chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 ( 1 cement :4coarse sand) for stop cock, with C.I Surface box 100x100x75mm (inside) with hinged cover fixed in cement concrete slab 1:2:4mix(1 cement:2 coarse sand:4 graded stone aggregate 20mm nominal size), I/C necessary excavation,foundation concrete 1:5:10(1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design: with common burnt clay F.P.S ( non modular) bricks of class designation 7 5
Providing and fixing C.P brass bib cock of approved quality conforming to IS 8931 :15MM nominal bore
Providing and fixing C.P brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690gms 15mm nominal bore
Providing and fixing C.P brass angle valve for basin mixer and geyser points of approved qualitty conforming to IS 8931 15MM NOMINAL BORE
Providing and fixing C.I dirt box stainer for bulk type water meter with nuts,bolts,rubber insertions etc. complete conforming to IS 2373 : 100MM dia.
Providing and fixing C.P Brass angle valve for basin mixer and geyser points of approved qualitty conforming to IS: 8931 15MM NOMINAL BORE
Providing and fixing 100 mm ( one hundred milimeter) dia,CP grating including carriage of material
Providing and fixing PVC ISI marked floor trap of self cleaning design including fixing with approved adhesive cost of cutting and making good the wall and floor :_ 110x75mm (one hundred ten into seventy five milimeter)
Providing and fixing on wall face high pressure PVC ( D-Plast) sewerage pipes of working pressure not less than 4.5 kg/sqm including filling the joints with approved adhesive complete
Providing and fixing high pressure PVC fittings and accessories ISI marked including fixing with approved adhesive washers etc. complete including carriage of materials with in all leads an lifts :_ Door bends of required degree ( any radius) :- with oval access door insertion rubber washer 3mm ( three milimeter) thick, bolts and nuts complete including carriage of material within all leads and lifts :- 75mm ( seventy five milimeter) nominal size
Providing and fixing collar with oval access door insertion rubber washer 3mm ( Three milimeter) thick, bolt and nuts complete 110mm (one hundred ten milimeter) nominal size
Providing and fixing bends of required degree complete 110mm(one hundred ten milimeter) nominal size
Providing and placing on terrace (at all floor levels) polyethylene water storage tank IS 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet,outlet and overflow pipes but without fitting and the base support for tank
Providing and fixing enclosed type water meter(bulk type) conforming to IS 2373 and tested by municipal board complete with bolt, nuts, rubber insertions etc.(The tail pieces if required will be paid separately): 80mm dia nominal bore
Constructing soak pit 1.20x1.20x1.20 m filled with brickbats including S.W. drain pipe 100mm diameter and 1.20 m long complete as per standard design
Providing and fixing ball valve(brass) of approved quality. High or low pressure, with plastic floats complete 15mm nominal bore
10 Liter capacity water heater ( Cat-A0
(Underground) Provision for Electrical Installation)
Karan jeet Attri
stage.html
html • 0.04 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .