PROVN OF 08 NO TOILETS NEAR COMMUNITY HALL BLDG NO P 52 AT SVN COLONY 104 AREA VISAKHAPATNAM

Amount

SCHEDULE'A' PART-I:B/R WORKS

Excavation in trenches, not exceeding 1.5 M wide and not exceeding 1.5 M depth and getting out in soft/ loose soil.

M&L for plain cement concrete (1:4:8), type D2 (using 40mm graded stone aggregate) as in foundation, filling of mass concrete.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick soft/loose soil.

Removing Excavated soils not exceeding 50 M and depositing where directed at a level not exceeding 1.5 M above the starting point.

Moorum/sand filling in floors laid in layers not exceeding 15 cm thick, spread, levelled and rammed including watering to required level and gradient.

M&L for hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface using broken stone or boulders

M&L for 75 mm thick Cement concrete type D 2, 1:4:8 (using 40 mm graded granite stone aggregate) in sub base of flooring

M&L for cement concrete 40mm thick type B-1, 1:2:4 ( 20mm graded aggregate) as in floor surface finishing even and smooth with using extra cement.

M & L for reinforced cement concrete M-30 (using 20 mm graded stone aggregate) as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc, basement slabs, under-reamed piles and mass concrete.

M & L for reinforced cement concrete M-30(using 20 mm graded stone aggregate) in beams, cantilevers, lintels over 1.5 m span.

M & L for reinforced cement concrete M-30 (using 20 mm graded stone aggregate) as in columns, pillars, piers, posts and struts etc.

M & L for reinforced cement concrete M-30 (using 20 mm graded stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, chajjas, landings, balconies, canopies, deck slabs and in shelves etc.

M & L for form work to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams, and similar work, vertical or to batter.

M & L for form work to sides and soffits of floor or roof beams, beam haunchings, girders, bressumers, lintels, cantilevers, shelves, including supports, overhangs, etc, also splays between floors and beams etc.

M & L for form work to soffits of suspended slabs such as roof slabs, floor slabs, landings, Chajja and similar work, not exceeding 200mm thick (Horizontal or sloping).

M&L for Mild steel TMT bars 10 mm dia., and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips.

M & L for Mild steel TMT bars upto 10 mm dia., cut to length, bent to shape required, in stirrups, spacers and binders and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips.

M & L Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in CM 1:6

All as Per item No. 11 above but half brick CM 1:4

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1:6 finishing the surface fair and even.

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1:4 finishing the surface fair and even using WPC as on external surface all as directed.

M&L fo Rendering 5 mm thick on fair faces of concrete surfaces in cement mortar 1:3 and finished even and smooth without using extra cement

M & L for preparing newly plastered surfaces of walls/ceiling and applying three coats of white wash on ceiling

Supply only Integral water proofing compound

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces.

M & L for coloured non skid ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding. 0.18 sqm on floor set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10 mm thick rendering in cement mortar (1:4) for backing of tiles.

M & L for Coloured Glazed ceramic tiles 300 x 450 x 7 mm thick, on vertical surfaces such as skirting, dados and risers to steps etc., set and jointed in neat cement slurry and pointed in white or Coloured cement to match over and including 10 mm thick rendering in cement morter (1:4)

M & L for preparation of new steel surfaces of any description, over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over one coat of red oxide priming.

M&L for plain cement concrete type C1, (1:3:6) (using 20mm graded stone aggregate) cast in situ in cills and other similar bands, plinth courses, parapets, copings, hold fast, bed plated and the like including use and waste of form work, weathering, slightly rounded or chamfered angles and throating as required.

Supply and fixing 30 mm thick Fiberglass Reinforced Plastic (F.R.P.) frame with flush door shutter in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF)/Polystyrene foam to be used as filler material throughout the hollow panel, casted monolithically with testing parameters of F.R.P. laminate conforming to table 3 of IS: 14856 complete all as specified by the manufacturer and as per directions of Engineer- in-charge.

S&F 200mm aluminium anodised barrel tower bolts of stove enameled black, with bright bolt and fixed.

S&F 250mm long aluminium alloy, anodised, sliding door bolt with hasp and staple, (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy.

S&F 150mm long extruded aluminium alloy handles, fabricated type, anodised.

S&F Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge.

S&F Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-Charge.

S&F 5.5mm thick sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each Extra over sheet glass, ordinary quality, if sheet glass is ground or obscured or frosted, on one side

S & F anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC15) of approved design/pattern, with approved standard section and fixed to the existing window frame C.P brass/stainless steel screws & 200mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-Charge.

Excavation in post hole(or similar holes) each n.exc 0.50 Cum getting out returning filling in and ramming earth around in layers n.exc 25cm watering and removed surplus soil to a distance n.exc 50m and making good surface in soft/loose soil.

S&F mild steel work with square / rectangular hollow section as in roof truss, purlins, rails etc. complete including one shop coat of zinc chromate primer paint.

M & L for 0.50mm thick prepainted galvalume aluminium zinc coating G.I. based corrugated steel sheet of on colour having tensile strength of 550MPa as in roof covering, fixed with and including self tapping screw complete all as per manufacturer instructions (Make : DYNA ROOF / TATA).

M & L for 0.50mm thick prepainted galvalume aluminium zinc coating G.I. based plain steel sheet of on colour having tensile strength of 550MPa as in roof covering, fixed with and including self tapping screw complete all as per manufacturer instructions (Make : DYNA ROOF / TATA).

S&F rotational moulded polyethylene water storage tanks (cyclindrical vertical with closed top) hoisted and fixed in position all as 1000 Litres including 20 mm size PTMT float valve with high density plastic ball (min weight 210 gms)

S&F 20mm ball brass valves,high pressure,with polythane float and flynut complete,screwed for iron pipe or brass ferrule .

S&Fof 15 mm stop valve cromium plated ,long shank & cup screwd down,high pressure,with crutch or butterfly, handle,screwd both end for iron pipe or for unions and fix.

S&F for pillar taps, cast copper alloy with capston heads, chromium plated, screwed down high pressure, with or without lettered hot or cold with long screwed shanks and fly-nuts, screwed for iron pipe 15mm bore. ( Make:Jaquar or equivalent).

S&F of 15 mm stop/angle valve cromium plated ,long shank & cup screwd down,high pressure,with crutch or butterfly, handle,screwd both end for iron pipe or for unions and fix.

S&F 3-layer PP-R P o l y p r o p y l e n e random copolymer)pipes 15 mm dia SDR 7.4 & SDR 11 UV stablised laid & concealed in walls including bends, elbows, unions etc, laid on walls for vertical stacks including chasing the wall and making good complete all as (Make: SFMC PN16/SDR7.4)

dito as above but 20 mm dia

S&F solid PVC door frame of size 50mm & 47 mm made out of 5mm plain colour PVC sheet reinforce with MS square tube supply & fixing in opening as per specification & drawing

S&F factory made solid PVC moulded door shutter, 28 to 30 mm thick (stiles) with 2,4,6 raised panel design with 2mm thick moulded PVC sheet on the front face & 2mm plain colour PVC sheet on back face, supply and fixing in frame at site as per specification & drawing

S&F 100 mm size stainless steel butt hinges ,bright finished .

S&F 150mm AL anodised cast type handle,.

S&F 150mm AL anodised extruded barrel tower bolts with bright bolt .

S&F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls,75 mm bore.

S&F PVC (SWR) vent cowl,75 mm bore

S&F PVC (SWR) floor trap, plain with grating including jointing with solvent including proper bedding and jointing with existing pipe

S&F 50 mm bore high density polyethylene pipes (HDPE) of pressure rating 6 kgf/cm2 fixed complete to walls, ceilings or in floors etc.

S&F Vitreous China Urinal, Half stall type, white including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe)

S & F Vitreous China wash down water closet pan (Pedestal pattern), white (ETWC) with ‘P’ or ‘S’ trap, white including connection to drain or outgoing pipe and to PVC flushing pipe, antisyphonage pipe,10 litres capacity PVC flushing cistern low level , valve less, symphonic action type complete with inlet ball valve, float and handle with brackets and plastic water closet seat cover, white, closed pattern with recessed bottom cover and mild steel chromium plated hinge all as specified and directed.

S&F in repair 10 Ltr capacity PVC valveless, syphonic action type flushing cistern, low level, white with inlet, ball valve, float and handle including brackets, complete all as directed. ( Make:JAQUAR/HINDWARE/CERA)

S&F chromium plaste jet spray for WC with 100cm long PVC pipe including necessary GI fitting as required like toe, nipple all as specified and as directed (Make : Cera or equivalent as approved).

S&F wash hand basin vitreous china white (flat back) of size 550x400mm including , CI bracket, 15mm dia polythene connection , 32mm dia chromium plated (CP) waste coupling chain and plug waste filling union and 32mm dia PVC waste pipe 90cm long etc. complete all as specified, and all necessary inlet outlet connections complete all as specified and directed.

S&F sheet glass (5-8mm thick) corner shelf 250mm radius including CP railing with bracket complete all as specified and as directed.

S&F chromium plated 20 mm dia tubular Towel Rail of 600 mm long including brackets and CP screws and fixing to wall complete .

S&F for Bib taps fancy type cast copper alloy, chromium plated for 15 mm bore pipe, screwed for iron pipes or for brass ferrule all complete as specified and as dierected.

Brushing neat cement slurry with 3 kg of cement per square metre .

Rendering 10 mm thick on concrete surfaces in cement mortar 1:4 mixed with WPC as directed and finished even and smooth to receive water proof treatment above 8 th storey upto 2nd floor complete all as specified and directed [NOTE: Supply only WPC shall be measured and paid separately]

APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application complete all as specified.

M & L for along the external wall below concrete or masonry spron using chemecal emulsion @ 2.25 ltrs per liners metre incl drilling and plugging holes etc in apron

M & L treatment of soil under existing floors using emulsion @ one lts per hole 300mm apart incl drilling and plugging 12mm dia holes with cement mortor 1:2 (1cement : 2sand) to match the existing floors

M&L cement concrete type C1 ,1:3:6 ( using 20 mm graded stone aggregate) 75mm thick as in plinth protection,path etc finished the surface even and fair w/o using extra cement complete all as specified and directed.

M & L of pre-polished cement concrete glossy finish chequred tiles, smooth in design as directed of size 300 x 300 x 25 mm thick compressive strength 300 kg/Sqcm, ISI marking (IS-13801-1993), set, jointed in neat cement slurry and pointed with white cement mixed with pigment to match over and including 20 mm thick screed bed in cement mortar (1:6).

S/F PP-R Gate valves (brass insert) of 20mm dia with iron wheel head screwed both ends for iron pipe and fixed etc .

Mild steel plates, plain or chequered, 6mm thick or over in thickness in available sizes

S&F in repairs 45 cm long PVC connection with two no PTMT nut and rubber washers suitable for 15mm bore GI Pipe all as specified

S&F Vitreous China Ladies urinal of minimum size 430x350x100mm white with grating and union for discharge pipe complete.

SCHEDULE'A' PART-II:E/M WORKS

Material and labour for point wiring with 1.5 Sqmm PVC insulated and unsheathed copper cable 1100V, FR grade multi-stranded drawn in and including suitable size of PVC conduit totally concealed/surface conduit in walls/ceiling with tee , bend, elbows , junction box etc. with provision of PVC insulated 1.5 sqmm copper conductor cable as earth continuity including prefabricated modular galvanised boxes with white modular cover plate of suitable size for fixing modular switches, sockets regulator and connected the earth wire to common earth dolly for One light/fan / bell point controlled by one switch/ bell push complete all as specified and as directed. [Note:-(i) The quoted rate shall includes all the cost of cutting, chasing, cementing work where required and making all the disturbed surfaces of wall I ceiling good to match the existing wall / ceiling with same colour.]

Description all as per item No. 78 above but for one 5 Amp switch socket out let on the same board with other switches complete all as specified

Description all as per item No. 78 above but for 15/16Amp switch socket out let, independent with 4.0sqmm copper conductor cable of PVC insulated, unsheathed, multi stranded and 4.0 Sqmm for earth continuity conductor, complete all as specified

S& F switch modular one way 6 Amps,1 module 230V complete all as specified.

S& F modular switch /way 16 Amps, 1 module 230V complete all as specified.

S& F bell push modular, one way 6 Amps, 1 module 230V complete all as specified.

S& F modular socket outlet 3 pin, 6 Amp 2 module 230V complete all as specified.

S& F modular socket outlet 3 pin, 6/16 Amp 2module 230V complete all as specified.

S& F ceiling rose surface bake lite 3 terminals complete all as specified.

S& F round shape 15 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft cool white/ warm white light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed..

S & F LED profile lighting consisting of aluminium extruded back strip casing LED/ neon strip, PVC diffuser and LED driver 12/24 V concealed in wall of cool white / warm white controlled by switch with all accessories complete all as specified and as directed.

S & F Exhaust fan , steel body AC single Phase 230V of size upto 300mm sweep with blades, frame and louvers including making suitable hole for fixing Exhaust fan and making good to disturbed surface , matching with existing paint complete all as specified and as directed.

S & F Building Security light LED 35 W Pressure die cast aluminium housing IP 66 protection with all accessories internally prewired (model: OSL-GRY-LPCRSRT36WXC of make: Jaguar or equivalent in other approved make) and including connecting up with twin core twisted copper conductor cable of suitable size including bracket made of 40mm dia GI light grade pipe of 1.2m long bent to shape fixed with suitable MS clamps, bolts, nuts and washers duly painted complete all as specified.

Supply and fix Exhaust fan, Metal body AC single Phase. 230V of size 300mm sweep with blades, frame and louvers including making suitable hole for fixing Exhaust fan and making good to disturbed surface, matching with existing paint complete all as specified and directed.

S & F MCB 6 to 32Amp, 240 Volt, SP, breaking capacity 10 KA 'C' series, complete all as specified

S & F MCB 6 to 32 Amp, 240 Volt, SPN, breaking capacity 10 KA 'C' series, complete all as specified

Supply lay and testing of cable in trenches/walls XLPE insulated, armoured electric cable (heavy duty 1100volt grade with stranded aluminium conductor of size 10 sqmm 4 core complete all as specified and directed by Engr-in-charge.

Excavation in trenches not exc,1.5m wide and not exceeding 1.5m in depth and getting out in hard/dense soil for laying of cable complete all as specified.

Returning, filling in, including spreading, levelling, watering and well ramming in layer not exceeding 25 cm thick complete all as specified

Removing excavated surplus soils meterial not exc.50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified.

Material and labour for natural river sand as cushioning of cables, including spreading and punning down complete all as specified and directed by Engineer in charge. Note : punned thickness shall be measured for payment

Supply and laying in trenches bricks common burnt clay building brick , sub class B designation 75 complete all as specified & directed

Supply and laying GI tubing light grade 40mm in trenches complete all as specified and as directed.

Earthing complete with Galvanised Steel Earth Plate Electrode 600 x 600 x 6 mm thick burried directly in ground Each(Earth Pit not less than 1.5 m below normal ground level connected to galvanised earth lead wire 4.0 mm as earth lead and GI pipe 15 mm, Medium Grade for earthing lead protection to the extent of maximum 7.5m, Earth Plate Electrode surrounded by 150mm thick packed layers of Charcoal and Common Salt filled in alternate layers, connected to the Plate by means of GI Bolts & Nuts complete all as per Electrical Plate No 3 of SSR Part - I, connected to panel/DB including testing on completion including main earthing, charcoal, Common Salt, PCC (1:2:4, Type B1) Pit with RCC 1:2:4, Type B1 Cover, 50mm thick with 6 Nos, 8 mm dia TMT bars in both ways, MS Funnels with 20 mm bore, medium grade GI watering Pipe, Wire Mesh, Earth Work excavation, return filling, removal of surplus soil etc. and disconnecting and taking down existing Earthing of any description complete all as complete all as specified and as directed.

Supply and lay pipe galvanized., "Medium class, including fittings 25 mm (1.0") dia in trench/ surface/walls ,etc and complete all as specified and directed

Supply and lay pipe galvanized, "Medium class", including fittings 60 mm (1,0") dia in trench/ surface/walls etc and complete all as specified and directed

Supply and fix gun-metal gate valves, with iron wheel, head, screwed both ends size 25mm complete all as specified and directed.

Cutting or screwing from existing GI/CI tubing of any size for alteration or additions suitable size for 25 mm dia complete all as specified and directed

Re-routing of existing GI/CI tubing of size upto 25-50 mm dia by disconnecting all connections and reflxing Including required tee, bends , elbows etc complete all as specified and directed

Venkat Associates (BID ID -3110711)

ESWAR ENTERPRISES (BID ID -3123918)

K NAGARAJU (BID ID -3102287)

SAI SAMPATH ELECTRICAL AND ENGINEERING (BID ID -3124181)

RAM SREE CONSTRUCTIONS (BID ID -3111392)

VENKATA SAI PRASAD VILLA (BID ID -3100618)