Replacing EI Work of conference hall of Narmada Water resources & Kalpasar department conference hall at 2nd Floor of Block-9 New sachivalaya campus at Gandhinagar.

BILL OF QUANTITIES(%TENDER)

:: BILL OF QUANTITIES::

Name Renovation EI work of conference hall of Narmada Water resources & Kalpasar Department conference hall at 2nd

of Floor of Block-9 New Sachivalaya Campus at Gandhinagar

Item No Description of item(with brief specification and reference to book of specifications) Qty Unit Amount

Replacing old & u/s by new Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire of 1.5

sq.mm (Green) both are of ISI marked 1.1 kV grade FRLS PVC insulated multi strand copper wires

up to 10 mtr length , in below type of pipe erected with 6A Modular type switch / bell push &

1 accessories and earth continuity of following type, erected on PVC / Metallic/Wooden box, single Pt. 491.87

mounting base frame covered with textured/metallic/white front plate modules erected on / in wall /

ceiling as per pipe erected, with necessary Lamp holder/ceiling rose / H.D.Connector as directed. (j)

in existing pipe erected concealed in wall/ceiling complete Cat. III

Replacing old & u/s by new Point wiring for FAN with 2-1.5 sq.mm & earth wire of 1.5 sq.mm

(Green) both are of .ISI marked 1.1 kV Grade FRLS PVC insulated multi strand copper wires up to

10 mtr length, in below type of pipe erected with 6A Modular type switch and hum free EME step

type electronic fan regulator mounted and accessories with earth continuity of following type

2 erected on PVC / Metallic/Wooden box, single mounting base frame covered with Pt. 667.61

textured/metallic/white front plate modules erected on / in wall / ceiling as per pipe erected. with

necessary ceiling rose / H.D.Connector as directed.(j) in existing pipe erected concealed in

wall/ceiling complete Cat. III

Replacing old & u/s by new Point wiring for on board Looped Plug with 6A Modular type switch & 5

pin socket erected on PVC / Metallic/Wooden box, single mounting base frame covered with

3 textured / metallic/white front plate modules erected on / in wall / ceiling with following type Pt. 309.06

accessories Cat. III

Providing following type of Modular Type Accessories mounted with PVC / metallic/Wooden box,

single mounting base frame covered with textured / metallic/white front plate , modules erected with

necessary connections as per site situation directed by Engineer In charge. (1)One No. SP

(2) One No 5 pin plug .Cat. III 26 Ea. 151.50

(7) Blank Plate Single Cat. III 10 Ea. 25.25

(9) 16 Amp. SP one way switch Cat. III 8 Ea. 180.79

(10) 6/16Amp. Universal socket Cat. III 8 Ea. 199.98

Replacing old & u/s by new Providing and erecting ISI mark Medium class RIGID PVC PIPES of

following size complete to be erected on/in wall or ceiling erected with necessary PVC fittings &

5 Junction boxes fixed with adhesive solution & Clamps with following dia of pipes, in approved Mtr. 24.24

manner as directed (a)20 mm

Providing & erecting PVC Corrugated Flexible Conduit with required nos. of coupling, PVC bushes,

6 Check-nuts etc. complete of following sizes.(1) 20 mm Mtr. 17.17

Replacing old & u/s by new Providing and erecting Mains with 1.1 kV grade FRLS PVC insulated ISI

marked stranded Copper conductor wire in following type of pipe to be erected concealed in

7 /flushed on wall/ceiling, with 1.5 sq. mm copper conductor FRLS PVC insulated stranded wire of Mtr. 58.58

green colour for earth continuity of following size (E) in existing pipe (a) 2 wire 1.5 sq. mm

(b) 2 wire 2.5 sq. mm

providing and erecting Mains with 1.1 kV grade FRLS PVC insulated ISI marked stranded Copper

conductor wire in following type of pipe to be erected in / on wall / ceiling with 2.5 sq. mm copper

8 conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size Mtr. 109.08

(E) in existing pipe (a) 2 wire 4 sq. mm

(b) 2 wire 6 sq. mm

9 Decorative call bell Ting-tong box type 250 volts complete erected 2 Ea. 71.71

Replacing old & u/s by new Supplying and erecting LED indoor fittings with LEDs of wattage 0.2

Watt to 0.5 Watt assembled on single MCPCB, with housing used as a heat sink shall be made of

thick sheet Steel conforming to IS: 513/CRCA/aluminium pressure die cast powder coated and high

U.V. & corrosion resistance with diffuser housed in aluminium casted body with company

160V to 270V,Power Factor more than 0.95, THD < 15 %,

Luminaire efficacy> 85 lumens/watt

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below description have shown ranges of

Wattage capacity of LED fittings.The Engineer incharge may select any wattage capacity between

the ranges shown.) (A) Square/ Circular shaped Surface/Recessed Mount Downlight with provision

for spring loaded mounting clips complete.IP20 (ii) 11-15 watts, Surge-2 KV Cat-lll

(iv) 22-24 watts, Surge-2 kV Cat-lll

(I) Adjustable spot light with COB led having aluminium reflector of following wattage (ii) 12 Watts

Cat-lll Ea. 966.57

SITC `17` mm to 22mm surface type alumium profile with presairmatic fiber cable with self adasive

led strip conforming to IS: 513/CRCA/aluminium pressure die cast powder coated and high U.V. &

corrosion resistance with diffuser housed in aluminium casted body with company mark/name

160V to 270V,Power Factor more than 0.95, THD < 15 %,

CCT 3000 K to 6500K,

11 Luminaire efficacy> 85 lumens/watt , Rn Mtr. 1610.95

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE: above description have shown ranges of

Wattage capacity of LED fittings.The Engineer incharge may select any wattage capacity between

the ranges shown.)

BILL OF QUANTITIES(%TENDER)

Item No Description of item(with brief specification and reference to book of specifications) Qty Unit Amount

providing and erecting Miniature circuit breaker single pole 6A to 25A suitable to operate on 240 V

12 A.C. system and having breaking capacity 10 KA to be erected in existing box. confirming to IS Ea. 123.22

8828/1996 with ISI Mark Cat.III

Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C Curve) having 10KA

breaking capacity & confirms to IS :8828 in existing box having following capacity (c)63 Amp.

13 Cat. III Ea. 811.03

Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface mounted

fitted with busbar, neutral link, earth bar and DIN rail, Conforms to IS 8623-1 & 3, IEC 61439-1 &

without MCB to house appropriate nos. of MCBs.(The DBs should be used of same company of

14 MCB to be used) suitable for (B) three phase incoming and single phase horizontal type outgoing Ea. 3412.79

Per phase isolation type (PPI) (b) sheet steel double door (iii)8 way

providing and erecting Approved make RCCBs conforming to IS: 12640 and having sensitivity of 30

mA and Short Circuit withstand capacity of 10 KA and suitable for operation on single phase

15 V,50Hz. having characteristic of quick action & tripping with all advance feature & do not incorporate Ea. 2458.34

any electronic component. for following Max. rating erected as directed (ii) 40Amps. DP Cat. III

Providing and erecting FRLS-XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Copper

16 conductor for 1.1 kV. to be laid on wall with necessary clamps or in existing trench / pipe at road Ea. 846.38

crossing or floor of following size of cables. (A) 4 core 10 Sq. mm

Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated

armoured cable complete with out going tails, insulating tape etc for following size of cables.(C) 2 to

17 4 core 10 Sq. mm Ea. 38.38

Solder less crimping type Copper lugs conforming to IS suitable for cable of following size evenly

crimped with high pressure tool & connected to switchgear terminals with brass/cadmium plated nut

18 bolts in an approved manner. (B) 10 Sq.mm Ea. 10.10

Supply, Installation, Testing and Commissioning of suitable sweep, BEE 5 Star rated, Ceiling fan

with Brush Less Direct Current (BLDC) permanent ferrite magnet Motor, class of insulation: B, Rust

free 3 nos.Aluminium blades, 2 nos. canopies, shackle kit with earthing provision, copper winding,

Power factor not < 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM,

350 RPM,230v (tolerance as per IS : 374-2019), THD < 10%, with remote unit for Speed Control

and all remaining accessories including safety pin, nut bolts, washers, temperature rise = 75 °C

(Max.), suitable for 140 to 285 Voltage and rectifier circuit with surge, over current and overload

protection , 50 Hz, Single phase AC Supply, earthing etc. Complete as required.[ Make shall be

approved by Engineer in Charge] (B) 1200 mm Sweep (48")

Supplying and erecting 19 / 20 mm. nominal bore Medium Class M.S. Pipe down rod erected duly

20 painted for fan complete with proper insulation without leakage and earthing. Mtr. 108.07

Supplying & erecting Fan Hook of 10 mm M.S. Round bar grouted in RCC slab with Making the site

21 as original. Ea. 43.43

SITC of Face Plate - Single (Keystone Jack,square) [Approved by Competent Authority i.e. not

22 Below the rank of Executive Engineer ] Ea. 90.90

SITC of Jack Cat 6 Keystone UTP [Approved by Competent Authority i.e. not Below the rank of

23 Executive Engineer ] Ea. 161.60

Supplying & erecting approved make LAN cable Cat 6A/Class EA cable shall be constructed of 23

AWG copper conductors with FEP Plenum (CMP) insulation. The copper conductors shall be

24 twisted in pairs and separated by a cross-divider. All four pairs shall be surrounded by a Mtr. 166.65

nonconductive foil tape and a flame retardant jacket. The foil tape shall suppress the effects of alien

crosstalk.Rate approved

Two lakh twenty-six thousand and fifty-seven point one nine

I/ We am/are willing to carry out the work at_________% above / below percent (should be written in figure & words) of the estimated mentioned above. Amount of

my / our tender works out as under.

Estimated amount put to Estimated amount put to

(a) I/we hereby declare that we have visited the site and fully exquisite myself/ourselves with the Local situation regarding materials labour and other factors

pertaining to work before submitting Tender.

(b) I/we hereby declare that we have carefully studies the conditions of contracts. Detailed Specification and other tender document of this work and agree to

execute the same accordingly.

1 If required and found necessary material to be used for this work and brought at site will have to sent to Govt.approved laboratory. The qualified agency/

manufacturer of Particular product under testing will have to pay/ bear necessary charges.

2 All works shall be carried out as per public works Department hand book and other Specification.

3 Rates are inclusive of 1% Labour cess in tender amount so 1% of total amount of bill will be deducted from the bill.

3 Rates are inclusive of 1% Labour cess in tender amount so 1% of total amount of bill will be deducted from the bill.

4 The material to be used in this work must be as per instruction by under liason of Engg. In charge.The agency will have to agree to carried out the work as

per brand/make demand of concern deptt.

5 Contractor must have registration in E-2 & above class registered under elect. (R & B) division.

BILL OF QUANTITIES(%TENDER)

Item No Description of item(with brief specification and reference to book of specifications) Qty Unit Amount

Sign of Dy. Exe. Engineer Exe. Engineer

ctor Sachivalay Complex Elect. Sub-Div.No.-2 Sachivalay Complex Elect. Div

R. & B. Deptt. Gandhinagar R. & B. Deptt. Gandhinagar

BILL OF QUANTITIES(%TENDER)

BILL OF QUANTITIES(%TENDER)