Construction of 4 Nos. type-II, III and IV quarters for Forensic Department at Sidhwari Dharamshala Distt. Kangra (HP). (SH- Ancillary works).

Amount

Excavation in foundation and trenches in earth work in all heights and depths in all kinds of soils, including saturated soils comprising of pick work, jumper work and blasting work both in soft and hard rock with chiseling and wedging out of rock (where blasting is prohibited) and their intermediate classification of soils including, dewatering wherever required, setting out to required lines, levels as shown on the drawing and directed by the engineer-in-charge at site., according to the HP.PWD. specification of 1990 (one thousand nine hundred ninety) volume-I (one) and sorting out useful and unuseful material and transportation of the unuseful material for disposing at dumping site (To be arranged by the contractor) including payment of MC/ local body dumping charges it lived any as per satisfaction of Engineer-in-charge through all modes of transportation including head load, animal load or mechanical means along with its leveling fine dressing and with all kinds of labour, machineries, tools equipments and safety measures and incidentals necessary to complete the work by mechanical means and labour (if required). All useful material such as stones, shingles aggregate and slates shall be properly stacked at site to the maximum possible extent in all leads and lifts through all modes of transportation and used/ removed as per the direction of Engineer-in-charge. Any loss to the public and private propriety during the course of execution and disposal of serviceable and unserviceable materials shall be absolute responsibility of the contractor and shall have to be duly compensated by him in all respects including all incidental charges.

Providing and laying cement concrete 1:4:8 (One cement : four sand : eight crushed stone aggregate 40mm (Forty millimeter) nominal size) including curing complete excluding cost of form work in foundation and plinth, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 nominal mix 1:3:6 ( 1 cement 3 Sand : 6 crushed graded stone aggregate 20mm nominal size) including carriage of materials, cost of formwork through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing concrete for plain/reinforced concrete in open foundations complete per drawings and technical specifications Clause 802, 803, 1202 & 1203 nominal mix 1:2:4 (1 cement 2 Sand : 4 crushed graded stone aggregate 20 mm nominal size) including cost of formwork and including carriage of materials, cost of formwork through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 80 mm thick C.C. paver block of M-30 grade approved by HPPWD (NTC/Ashok Panjla Tiles/NTCCI/Pooja Concrete Fabricators, M/S Dalal Tiles Pvt. Ltd.) with approved color design and pattern including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete in all heights Thermo-Mechanically Treated bars of grade Fe-500D or more. including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Full Brick work using common clay burnt building bricks in super structure above plinth level upto all heights with in cement mortar 1:6 (1 cement :6 sand) 1st class bricks including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Steel work welded in built up sections,trusses and framed work including cutting,hoistingm,fixing in position and applying a priming coat of read lead paint in:- In gratings framed guard bars,ladders,railing brackets and similar works. including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Painting two coats(excluding priming coat)on steel and other metal surfaces with enamel paint,brushing to give an even shade including cleaning of all dirt, dust and other foreign matter.Enamel paint other than white. including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing 0.60 mm thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organiccoating of 20microns over 5 mocrones primer coating i/c fixing with prepainted iron J or L hooks bolts and nuts 6 mm dia meter with prepainted limpet and rubber washers complete with all accessories as required asper the direction of Engineer- in- charge including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing flushing 38cm overall with 0.60 mm thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organiccoating of 20microns over 5 mocrones primer coating i/c fixing with prepainted iron J or L hooks bolts and nuts 6 mm dia meter with prepainted limpet and rubber washers complete with all accessories as required asper the direction of Engineer- in- charge including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

15mm cement plaster in single coat on the fair rough side of brick / concrete / stone walls for interior plastering upto floor two level including arrises, internal rounded angles, chamfers and / or rounded angle not exceeding 80mm in girth and finished even and smooth in cement mortar 1:6 (1cement : 6sand) including carriage of material within all leads and lifts.

Applying birla white wall care putty (two coat) over plaster surface after throughly brushing the surface free from mortar drops, dust, loose materilas and other foreign matters and papered smooth to give final matter finish to the surface complete including carriage of material within all leads and lifts.

Distempering (two coats) with oil boud washable disremper of approved brand and manufacture and of required shade on decorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and menufacture after throughly brushing the surface free from mortar dropping and other forign matter and also including preparing the surface even and sand papered smooth prming coat with distemperr primer including carriage of material within all leads and lifts.

Finishing wall with weather proof exterior grade emulsion of approved design (Apexultima) or its equarlied on undecorated wall surfaces (two coats) to give an evenshade after throughly brushing the surface to remove all dirt dust and other foreign matter etc includingsand paper smooth including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fxing aluminium work for door, windows, ventilators and partitions with extruded built up standard tubular and other sections to of approved make . conforming to 733 and IS 1285 anodised transparent or dyed to required shade according to IS 1868.(Minimum anodic coating of grade AC 15 ) fixed with rawplugs and screws or with fixing clips, or with expansion hold fastners i/c necessary filling up of gaps at junctions , at top , bottom and sides with frequired PVC/ Neoprene felt etc. aluminium sections shall be smooth ,rustfree ,straight ,mitred and jointed mechanically where ever required i/c cleat angle, aluminium ,snap beading for glazing /panelling C.P. brass/ stainless steel screws .All complete as per Architectural drawing and the directions of Enginner in charge including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.. a)For doors windows and ventilators and glazed partitions frames.

Providing and fixing Aluminium composite panel sheet 5 mm thick including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing on wall face PVC (D-Plast)rain water pipe of working pressure not less than 6.5kg/sqm. including filling the joints with approved adhesive complete including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.. a) 110mm dia pipes.

Providing and fixing on PVC accessories for water pipes including filling the joints with approved adhesive including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..(a) 110mm dia plain bend

150mm dia plain bend

Digital wall tiles 6mm thick in skirting risers or steps and dado on 12mm thick cement plaster 1:3(1cemen:3sand) and jointed with white cement slurry including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge..

Providing and laying cement concrete flooring 1:2:4 (1 cement :4 sand : 4 graded stone aggregates 20mm nominal size ) laid in one layer finished with a floating coat of neat cement. 50mm thick including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality Rectangular shape 600x450 mm internal dimensions including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Demolition below G.L. upto 1.50Metres depth and disposal of unserviceable materials within all lead and lifts .un-reinforced cement concrete upto than 15 cm. Thickness including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Supplying and fixing glass panes with putty and nails including removal of broken glass panes wherever necessary. Glass 4 mm thick including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing special quality chromium plated brass cupboard locks with six levers of approved quality including necessary screws etc. complete. Size 65mm including carriage of material within all leads and lifts.

Providing and fixing nickel plated M.S. pipe curtain rods with nickel plated brackets complete .20 mm dia (heavy type) including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Desludging of septic tank and disposing of all surplus material as directed including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Ajeev Kumar