Construction of 6 Nos. Type-III , 6 Nos. Type-II and 6 nos. Type-1 Staff Quarter near CMO Residence at Dharamshala in District Kangra (HP) (Deposit Work )

Amount

Excavation in foundation, trenches etc. in earth work in all classification of soil such as pick work, jumper work, pick jumper work, blasting work, jumper blasting work, soft and hard blasting and saturated soil, de-watering, including wedging out rocks where blasting work is prohibited, chiseling or any other mixed variety of soil, including shoring, shuttering and pumping out water upto any depth or any quontam of water including slush which may be arise during de-watering removal of slush and stacking the serviceable and un-serviceable material clear from the edge of excavation as direction of Engineer-In-Charge and retuning the stacked soil in 15cm (Fifteen centimeter) layers, when required into plinths, sides of foundation etc; consolidating each deposited layer by ramming, watering and then disposing of all excavated earth as directed by the Engineer-in-Charge, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rates inclusive of octori, royality, Malkhana, toll taxes, GST and any other taxes imposed by the Government.

Cutting in earth work in all kind of soil by mechanical means including saturated soil comprising of ordinary soil, soft rock, hard rock, chiseling, wedging out of rock (where blasting is prohibited) and their intermediate classification of soil, setting out true to the required lines, grades, cutting and trimming of side slopes and level as shown in the drawing and as directed by engineer-in-charge at site according to the MORD technical specification clause 302, 304 and 1603 and sorting out useful materials and stacking the same in all leads and lifts in acquired width of road and transportation of useful material for filling in road ways, camber, embankments for grade improvements and disposal of all surplus material to required width of the road or on approved dumping sites through all modes of transportation including head load or animal transport or mechanical means along with its leveling, fine dressing and carriage of machineries, materials, tools, equipments and safety measures and incidentals necessary to complete the work by mechanical means and labour if required. Recovery of stone to the tune of 135.00 cubic metres quantity at the rate of 300/-(Rupees Three hundred) per cubic metre shall be effected from the contractor's running bills on pro-rata basis as per actual quantity executed. Any loss to the public, private property during the course of execution shall be the absolute responsibility of the contractor, which shall have to be compensated by him in all cases including carriage of matereials within all leads and lifts and other incidentals The rate including octroi, royality, Malkana, toll tax, sale tax or other taxes imposed by the Government. .

Filling in plinth with sand of approved quality under floors including watering ramming, consolidating and dressing complete as per HPPWD specifications and as directed by Engineer-in-Charge, including carriage of material within all leads, lifts and other incidental Charges. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sale Tax, GST or any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in Foundation footings, bases of columns and mass concrete within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in flat surfaces such as soffits of suspended floors roofs, landings as per Architectural drawing and the like within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in columns pillar posts and struts Square, rectangular or polygonal in plan within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in beams cantilevers girders and lintels sides and soffits of beams, beam haunchings, cantilevers, bressumers and lintels upto all depths within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal one five millimeters) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimeters), so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in vertical surfaces such as walls (any thickness) partitions and the like including attached pillasters, buttresses plinth and string courses and the like within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing form work with steel plates of 3.15mm (Three decimal fifteen millimetres) thick, welded with angle iron in frames of 30x30x5mm(Thirty into Thirty into Five millimetres),so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights and removal of the same for in-situ reinforced concrete and plain concrete work in stairs cases with slopping or stepped soffits, excluding, landing, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal fifteen millimetres) thick, welded with angle iron in frames of 30x30x5mm(Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etc, with wooden battens and ballies for all heights and removal of the same for in-situ reinforced concrete and plain concrete work in edges of slabs and breaks in floors and walls under any thickness within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and laying cement concrete 1:6:12 (One cement isto Six sand isto Twelve graded broken/crushed stone aggregate 40mm (Forty millimeters) nominal size and down gauge) mechanically mixed and curing complete excluding cost of forms work in foundation and plinth, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and laying cement concrete 1:4:8 (One cement isto Four sand isto Eight graded broken/crushed stone aggregate 40mm (Forty milimetres ) nominal size and down gauge) mechanically mixed and curing complete excluding cost of forms work in foundation and plinth within all leads, lifts of materials and other incidentals as per approved specification, drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and laying cement concrete 1:5:10 (One cement isto Five sand isto Ten graded broken/crushed stone aggregate 40mm (Forty milimetres ) nominal size and down gauge) mechanically mixed and curing complete excluding cost of forms work in foundation and plinth within all leads, lifts of materials and other incidentals as per approved specification, drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and laying in position machine batched and machine mixed cement concrete work of grade M-20 ( M- twenty) design mix to obtain the compressive strength of 20N/mm 2 (twenty newton per Square milimetre) for reinforced cement concrete work, using cement with cement content not less than @ 330 kg/cum. ( three hundred thirty kilogram per cubic metre) or as per approved design mix for all work upto plinth level to give a smooth surfaces mechnically mixed and vibrated including curing complete and pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals.. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and laying in position machine batched and machine mixed cement concrete work of grade M-20 ( M- twenty ) design mix to obtain the compressive strength of 20N/mm 2 (twenty newton per Square milimetre ) for reinforced cement concrete work, using cement contents not less than @ 330 kg/cum. ( three hundred thirty kilogram per cubic metre) and as per approved design mix for all work above plinth level to give a smooth surfaces mechanically mixed and vibrated including curing complete and pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate inclusive of Malkhana, Royality, Octroi, toll tax or any taxes imposed by the Government.

Providing and laying Damp Proof Course 100mm (One Hundred milimetres) thick with cement concrete 1:2:4 (one cement: two sand: four graded crushed stone aggregate 12.5mm (Twelve decimal five milimetres nominal size) and curing complete, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Applying a coat of hot bitumen mexphalt 80/100 (Eighty/Hundred) 1.70 Kgs. (one decimal seventy Kilogram’s) per square metre. On Damp Proof Course after cleaning the surface with a piece of cloth lightly soaked in kerosene oil; within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing Tor steel reinforcement of Sail / Tisco /Tata for reinforced cement concrete work including bending, binding, straighting, cutting and placing in position complete including cost of binding wires complete for all floors within all leads, lifts of materials and other incidentals as per approved specification, drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Random rubble masonry/polygonal rubble masonry (uncoursed/brought to courses) with hard stones of approved quality in foundation and plinth at plinth level in Cement Mortar 1:6 (one cement isto six sand) including levelling with cement concrete 1:6:12 ( one cement isto six sand isto twelve graded stone aggregate 20mm (twenty millimetre) nominal size including entire carriage of materials in all leads and lifts and as per the direction of Engineer-in-Charge.

Second class brick work using common burnt clay building bricks in super-structure upto all floor level in cement mortar 1:6 (One cement isto Six sand) and curing complete,within all leads, lifts of materials and other incidentals, as per approved specification, drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Second class half brick work using common burnt clay building bricks in super-structure upto all floor level in cement mortar 1:4 (one cement :four sand) within all leads, lifts of materials and other incidentals, as per approved specification, drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and Fixing 40mm (forty milimetres) thickness first class deodar wood shutter having 12 mm (twelve millimetre) thick aluminium composite panel with frame of Ist class deodar wood for doors including bright finished iron butt hinges with necessary screw as per approved shade within all leads, lifts of materials and other incidentals as per approved specification, drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing factory made PVC door frame single rebate of any clours of size 50x47mm with a wall thickness of 5mm made out of extruded 5mm rigid PVC foam sheet heat bend & mitred at corners and jointed with 2 Nos. of 150mm long brackets of 15mmx15mm M.S. square tube, the vertical door profiles to be reinforced with 19mmx19mm M.S. square tube of 19 gauge EPDM rubber gasket weather seal to be provided throughout the frame i/c fixing of door frame to wall with M.S. screws 100long with wooden or rawl plugs emedded in masonry complete as per approved shade within all leads, lifts of materials and other incidentals as per approved specification, drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing to existing door frames, 30mm (Thirty millimetres) thick factory made PVC panelled door shutter consisting of frame made out of M.S. tubes of 19 (Nineteen) gauge thickness and size of 19mm x19mm (Nineteen into nineteen millimetres) for styles and 15mmx15mm (Fifteen into fifteen millimetres) for top & bottom rails, code 9.120 of Rajshri M.S. frame shall have a coat of steel primers of approved make and manufacture M.S. frame covered with 5mm (Five millimetres) thick heat moulded PVC "C" channel of size 30mm (Thirty millimetres) thickness, 70mm (Seventy millimetres) width out of which 50mm (Fifty millimetres) shall be flat and 20mm (Twenty millimetres) shall be tappred in 45 (Forty five ) degree angle on either side forming style and 5mm (Five millimetres) thick, 95mm (Ninety five millimetres) wide, PVC sheet out of which 75mm (Seventy five millimetres) shall be flat and 20mm (Twenty millimetres) shall be tapered in 45 (Forty five) degree on the inner side to form top and bottom rail and 115mm (One hundred fifteen) wide PVC sheet out of which 75mm (Seventy five millimetres) shall be flat and 20mm (Twenty millimetres) shall be tapered on both side to form lock rail, top, bottom and lock rail shall be provided either side of the panel 10mm (Ten millimetres) thick, 20mm (Twenty millimetres) wide cross PVC sheet be provided as gap insert for top rail and bottom rail paneling of 5mm thick both side PVC Sheet to be fitted in the M.S. frame welded/sealed to the style & rails, joints mitred and jointed with solvent cement adhesive i/c fixing of PVC shutter with existing frame with M.S. butt hinges 100x50x1.90mm ( One hundred into fifty into one decimal ninety millimetres) size with necessary screws etc complete as directed by the Engineer-in-Charge.within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 40mm (forty millimetres) thick second class deodar wood, panelled glazed or panelled and glazed shutters for doors windows and clerestory windows including black enamelled iron butt hinges with necessary screws, within all leads, lifts of materials and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge.The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 40mm (Forty milimetres) thick second class deodar wood wire gauge shutters using galvanized M.S. wire gauge of IS gauge designation 85 G with wire of 0.56mm (Zero decimal five six milimetres) diameters for doors, windows and clerestory windows including bright finished /black enameled iron hinges with screws within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Complete box of cupboard of 19mm (Nineteen millimetres) thick water proof termite resistant commercial board Uniply / Green ply /Kit ply /Dura ply / Marino (ISI Marked ) for shutter including 19mm thick shutter. Back side of cupboard shall be 6 to 8 mm (six to eight millimetre) thick water proof ply. The shutter from all side shall also have 6mm (six millimeter) thick hard board edging/ Topping to be finished with 1mm (one millimeter) thick mica lamination of Century / Greenlam / Action Tesa / Merinolam approved shade of office including fixing handles be provided in wood colour with nickel plated piano hinges with screws etcetera within all leads, lifts of materials and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government. (Note:- The measurement shall be made for outerface only)

Providing and fixing 19mm (Nineteen millimetre) thick water proof terminate resistant commercial board Century/Alpro or equivalent in shutters for SDB/cup boards with 6 mm (six millimetre) thick hard wood edging all round and PGI sheet lining in side i/c fixing with nickel plated piano hinges with screws etc complete) within all leads, lifts of materials and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing 15mm thick aluminium composite panel sheet ceiling with butt jointing and nail including G.I. framing complete within all leads, lifts of materials and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 25mm diameter C.P. curtain rod and brackets including fixing with etc. complete i including carriage of materials within all leads, lifts of materials and other incidentals, as per approved specification, drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing M.S plain grills of required patterns in frames of windows etc. with M.S flats, square or round bars with round headed bolts and nuts or by screws Plain grill including entire carriage of materials in all leads and lifts.

Providing and fixing 300x16mm (Three hundred into Sixteen milimetres) size Pilot/sheel anodized aluminium sliding door bolts anodized transparent or dyed to required colour and shade with necessary screws etc. within all leads, lifts of materials and other incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing aluminium Pilot/sheel anodized transparent or dyed to required colour and shade with necessary screws etc.Tower bolts (Barrel type) as approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

250x10mm (Two hundred into Ten milimetres) size

150x10mm (One hundred fifty into Ten milimetres) size

Providing and fixing aluminium Pilot/sheel or equivalent anodized transparent or dyed to required colour and shade and of approved make with necessary screws etc. handles with the necessary screws etc. complete. within all leads, lifts of materials and other. incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

125mm (One hundred twenty five milimetres) size

Providing and fixing 150mm size M.S. double acting spring bright finished with necessary screws etc;as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing oxidized 200mm size M.S. hooks and eyes complete in all respect;as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing 25mm (Twenty five milimetres) thick Kota Stone in flooring 55x55cm (Fifty five into Fifty five centimetres) (Mirror polished) with 7.5 cm (Seven decimal Five centimetres) wide Jaislmer yellow (uniform colour) marble band base of 20mm (twenty millimeter) thick cement mortar 1:4 (One cement: Four sand) laid over and jointed with Grey cement slurry mixed with pigment to match the shade of the slab including rubbing, polishing moulding and nosing complete within all leads, lifts of materials and other. incidentals. as per approved architectural drawing, design and specification as directed by the Engineer-in-Charge . The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

50mm (fifty milimetres) thick cement concrete flooring 1:2:4 (One cement isto Two sand isto Four graded crushed stone aggregate 20mm (Twenty milimetres) nominal size and down gauge) laid in one layer finished with a floating coat of neat cement within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing 10mm (ten milimetre) thick double charged matt finished vetrified tiles of Nitco / Simpolo / Orient -Bell / Rak/ Kajaria / AGL/Johnson / Somany as per approved shade and design 600x600mm of size (six hundred millimetre into six hundred millimetre) manufactured of approved shade and colour in flooring and landings laid over 12mm (twelve millimetre) thick cement mortar 1:3 (one cement isto three sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete within all leads, lifts of materials and other. incidentals. as per approved architectural drawing, design and specification as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and laying 300X300 mm (three hundred into three hundred millimetre) antiskid Ceremic tile of Orient/RAK/Kajaria/Somany/Johnson/ Bell in flooring on 12mm (twelve millimetre) thick cement mortar 1:3 (one cement isto three sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete within all leads, lifts of materials and other incidentals. as per approved architectural drawing, design and specification as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and laying 25mm thick mirror polished kota stone in skirting/ dado laid on 12mm ( twelve millimeters ) thick in cement mortar 1:3 ( one cement is to three sand and jointed with grey cement slurry with pigment to match the shade of the kota stone i/c rubbing and mirror polishing complete within all leads, lifts of materials and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

15 mm thick Cement plaster skirting (upto 30cm height) with cement morter 1:3 (1 cement:3 sand) finished with a floating coat of neat cement including rounding of junction with floor complete within all leads, lifts of materials and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and laying ultra charged vetrified tiles of Nitco / Simpolo / Orient -Bell / Rak/ Kajaria / (Eternity) /AGL/Johnson / Somany as per approved shade and design 300x300mmx10mm (three hundred millimetre into three hundred millimetre into ten millimetre) in skirting risers of steps and dados on 12mm (twelve millimetre) thick cement mortar 1:3 (one cement isto three sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete within all leads, lifts of materials and other incidentals. as per approved architectural drawing, design and specification as directed by the Engineer-in-Charge

Providing and laying 300X450 mm (three hundred into four hundred fifty millimetre) white Glazed tile of Kajaria/ Swastik / Somany / Bell / AGL/Johnson in skirting risers of steps and dados on 12mm (twelve millimetre) thick cement mortar 1:3 (one cement isto three sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete within all leads, lifts of materials and other incidentals. as per approved architectural drawing, design and specification as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and laying 19mm (nineteen millimetre) thick polished Grey/ Black granite in under counter wash basin & water trough with semi round nosing 20mm (twenty millimetre) (average) thickness base of cement mortar 1:3 (one cement isto three sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of granite stone including rubbing and polishing complete within all leads, lifts of materials and other. incidentals. as per approved architectural drawing, design and specification as directed by the Engineer-in-Charge

Providing and fixing 0.60mm (Zero decimal Six Zero milimetres) thick prepainted steel sheet ISI marked - Z 120 of Tata Durashine/ Sail / Reliance / Jindal steel in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster (RMP) organic coating of 20 (Twenty) microns over 5 (Five) microns primer coating to back coat of polyster of 5 (five) microns over 5 (Five) microns primer fixing with prepainted iron J or L hooks,bolts and nuts with prepainted limpet and rubber washers complete with all accessories as required within all leads, lifts of materials and other. incidentals. as per approved architectural drawing, design and specification and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing valleys 90 cm (ninety centimetres) over all over all with 0.60mm (Zero decimal Six zero milimetres) thick prepainted sheet ISI marked - Z 120 of Sail / TATA / Relience / Jindal steel roofing with hot dipped metallic Zinc coated sheet with top coat of regular modified polyester (RMP) organic coating of 20 (Twenty) microns over 5 (five) micron primer coating, back coat of polyster of 5 (Five) microns including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (Six milimetres) diametres with prepainted G.I. limpet and bitumen washers complete with all accessories as required within all leads, lifts of materials and other incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing ridges or hips 60 cm (Sixty centimetres) over all with 0.60mm (Zero decimal Sixty milimetres) thick prepainted steel sheet ISI marked - Z 120 of approved make in ridges of Sail / Relience / Jindal /Tata Durashine with hot dipped metallic Zinc coated sheet with top coat of regular modified polyester (RMP) organic coating of 20 (Twenty) microns over 5 (Five) microns primer coating of back coat of polyester of 5 (Five) microns over 5 (Five) microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (Six milimetres) diametres with prepainted G.I. limpet and bitumen washers complete with all accessories as required within all leads, lifts of materials and other. incidentals. as per approved architectural drawing, design and specification as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 30cm (thirty centimeters) wide 25cm (twenty five centimeters) deep of Tata/ Sail / Jindal Steel 0.60mm (Zero decimal Six zero milimetres) thick plain G.I. gutter with iron brackets 40x3mm (Forty into Three milimetres) size bolts and nuts and washers etcetera including making necessary connections with rain water pipe and providing complete accesories within all leads, lifts of materials and other. incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing plain M.S. B.P. sheet of TATA/SAIL/JINDAL steel 2.00 mm (Two decimal zero millimeter) thick fixed in eaves board / facia / soffits /ceiling including cutting, fixing and welding to steel rafter, member and applying a coat of red lead primer with gas/ electric welding in position complete (frame work is to be measured and paid for separately) within all leads, lifts of materials and other. incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing on wall face 110mm (One hundred ten milimetres) diametres P.V.C. rain water pipes of working pressure 4/6kg (four / six kilogramme) per square centimetre of finolex / Relience / vectus/ prince pipe for rain water pipe fixed with approved adhesive including filling the joints complete within all leads, lifts of materials and other incidentals, and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing on wall face P.V.C. acessories for rain water pipes of working pressure 4/6kg (four / six kilogramme) per square centimetre of finolex / relience / vectus ./ Prince or its equivalent for rain water pipe fixed with approved adhesive including filling the joints complete in all requirement within all leads, lifts of materials and other incidentals. and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

110mm (One hundred ten milimtres) diametrees PVC Plain bend

110mm (One hundred ten milimtres) diametrees PVC shoe

Providing and fixing PVC holder bat clamps of approved design to P.V.C.. rain water pipe embedded in and including cement concrete blocks 10x10x20cm of 1:2:4(One cement: Two sand: Four graded crushed stone aggregate 20mm (Twenty milimetres) nominal size and cost of cutting holes and making good the walls etc; within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

100mm ( one hundred ten milimetres) diameter.

Providing and fixing angle iron door frames (Single rebate) manufctured from M.S angle section of 40x40x5mm and M.S. flat 50x5mm as design and drawing including jamb, lock jamb, beed and if required angle threshold of M.S. angles 50x25mm welded or regidly fixed by mnechanical means lugs with spit ends to each jamb includng steel butt hinges 2.5mm thick with a provision of locking arrangment and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surfaces within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing angle iron door frames (Double rebate) manufctured from M.S angle section of 40x40x5mm and M.S. flat 50x5mm as design and drawing including jamb, lock jamb, beed and if required angle threshold of M.S. angles 50x25mm welded or regidly fixed by mnechanical means lugs with spit ends to each jamb includng steel butt hinges 2.5mm thick with a provision of locking arrangment and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surfaces. within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and Fixing MS Channels In doors and window frames manufactured from MS Chaneel sections 75x40x6 mm (seventy five into forty into six millimetre) MS angle iron 25x20x3mm (twenty five into twenty five into three millimerte) MS T- Sections 25x25x3 mm (twenty five into twenty five into three millimerte) and Z-Sections as per detail flat 40x12 mm (forty into twelve millimetre) combination as per design drawing including hinges, jambs, if required threshold of MS angles 50x25 mm (fifty into twenty five millimetre) welded or rogidily fixed by mechanical means lugs with split ends tails to each jambs including steel but hinges 2.5 mm (two decimal five millimetre) thick with the provision of locking arrangements shock absorbers and sepcified and applying a coat of aproved primer after pre treatment of surfaces as directed by Engineer in Charge, within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. .

Steel work welded in built up sections of TATA/SAIL joists channels, angles, tees with connection plates or angles, cleat as in trusses, trussed purlins main and cross beams, hips jack rafters, purlins connected to common rafters and the like in building including cutting, fixing, lifting, hoisting and; placing in position complete and applying a coat of red lead paint within all leads, lifts of materials and other. incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge

Providing and fixing fan clamps of type -1of 16mm diameters M.S. barbent to shape with hooked ends to Reinforced Cement Concrete slab during laying including painting the exposed portion of loop all as per standard design complete as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Applying priming coat With ready mixed priming paint, brushing Asian paint/ Nerolac/Berger of approved shadeover new steel and steel based surfaces after and including preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter sand paper and knotting complete including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge

Painting two or more coats (excluding priming coat) on new steel and other metal surfaces with enamel paint brushing of Asian paint/ Nerolac/Berger of approved shade to give an even shade including cleaning the surfaces of all dirt, dust andother foreign matter enamel paint other than white within all leads, lifts of materials and other incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Applying priming coat over new wood and wood based surfaces after and including prepering the surface by thoroughly cleaning oil,grease,dirt and other foreign matter) sand papering and knotting with ready mixed paint brushing wood primer pink within all leads, lifts of materials and other incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Painting two or more coats of Nerolac/Asian paint/ Berger (excluding priming coat) on new wood and wood based surface with enamel paint other than white to give an even shade including cleaning the surface of dirt,dust and other foreign matter,sand papering and stoping within all leads, lifts of materials and other incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

6mm (Six milimetres) thick cement plaster in ceiling with cement mortar 1:3 (One cement: Three sand) for all heights within all leads, lifts of materials and other incidentals as per approved approved specification, drawings and design. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

15mm (Fifteen milimetres) thick cement plaster in single coat on rough side of brick/concrete/stone walls for interior plastering upto all floor levels including arises internal rounded angles, chamfers and or rounded angles not exceeding 80mm (Eighty milimetres) in girth and finished even and smooth with cement mortar 1:6 (One cement isto six sand) within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

15mm (Fifteen milimetres) thick cement plaster in single coat on fair side of brick/concrete/ stone walls for interior plastering upto all floor levels including arises internal rounded angles, chamfers and or rounded angles not exceeding 80mm (Eighty milimetres) in girth and finished even and smooth with cement mortar 1:6 (One cement isto six sand) within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

15mm (Fifteen milimetres) thick cement plaster in single coat on fair side of brick/concrete/ stone walls for exterior plastering upto two floor levels including arises internal rounded angles, chamfers and or rounded angles not exceeding 80mm (Eighty milimetres) in girth and finished even and smooth with cement mortar 1:5 (One cement isto five sand) within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Wall Painting (two or more coats) with Interior emlusion paint of Nerolac/ Asian paints of approved brand and manufacture and of required shade on ceiling/sloping roof surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth.Priming coat with distemper primer within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge.

Finishing wall with Apex weather proof exterior grade emulsion of Asians Paints /Nerolac suraksha /Bergur paint Exterior Emulsion as per approved shade approved design (Apexultima) on undecorated wall surfaces (two coats) to give an even shade and final finish after throughly cleaning the surface to remove all dirt, dust and other foreign matter etc including sand paper smooth complete within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing Plinth protection with 40 mm (forty millimetre) thick interlocking paver blocks of NTC with 23 cm (twenty three centimetre) dia. Half round R.C.C. pipe for drainage purpose laid base over of 10 cms ( ten centimetre) thickness cement concrete 1:4:8 (one cement isto four sand isto eight graded / crushed stone aggregate) 40mm (forty millimetre) nominal size for bedding of pipe complete within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing railing for stair case 85cm height having baluster of 19×19 mm (nineteen into nineteen millimetres) and 12x12mm (twelve into twelve mimlimetres) square hollow M.S. (Mild steel) with a clear height of 85mm (Eighty five millimetres) at the rate 60mm (Sixty millimetres) c/c jointed in cement slurry and eletric gas welded at top alongwith hard wood (teak wood 2ns class) hand rail and 75x65mm vertical balusters jointed with each other with 2 nos M.S. flat of 40x6mm complete with applying of red laid paint within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 6mm (six milimetre) thick asbastes cement sheet ceiling ISI Marked complete in all respect within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Applying Birla / J.K white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 600 x600 x15 mm (six hundred into six hundred into fifteen millimetre) Everest Fibre cement board/ACP Pannel of all covering with prepainted G.I. Channel system and 600mm i/c necessary fittings complete in all respect as per approved design/drawings & specifications.The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and laying heavy duty 60mm (sixty milimetres) thick inter locking paver blocks precast cement concrete of NTC inter locking paver blocks vibro compacted upto M-50 (M-Fifty) grade including border or kurb block Grey or coloured over sub-base of concrete with 25mm (Twenty five milimetres) thick average thickness of cement mortar 1:4 (One cement : Four sand) laid over and jointed with neat cement slurry mixed with pigment to match the shade of blocks including curing rubbing and polishing complete (sub-base concrete floor to be paid for separately) within all leads, lifts of materials and other incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

60mm (sixty milimetres) thick inter locking paver blocks

Excavation in drains and channels etc; in earth work in all kind of soil, such as pick work, jumper work, pick jumper work, blasting work, hard and soft blasting, saturated soil including chiseleing or any other mixed variety of soil, lift upto any heights, stacking the excavated soil for all heights from the edge of excavation and then returning the stacked soil in 15cm (Fifteen centimetre) layer when required into plinths sides of foundations etc. Consolidating each deposited layer by ramming, watering and then disposing of all surplus excavated earth as directed by the Engineer- Incharge, within all leads, lifts of materials and other incidentals. As per approved drawing, design and as directed by the Engineer-in-Charge. The rates are inclusive cost and carriage of materials with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. Rate inclusive toll tax, GST and any other taxes imposed by the government.

Providing and laying cement concrete 1:3:6 (1 cement : 3 sand : 6 graded stone aggregate 20 mm nominal size) and curing complete excluding cost of form workin: foundation and plinth as per Architectural drawing ,design and specifications as per approved specification, drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, including the cost of centering, shuttering and finishing as per direction of Engineer-in-charge In cement mortar 1:4:8 (one cement isto four coarse sand isto eight graded stone aggregate 20 mm ( twenty milimetres) nominal size) , as per approved drawing, design and specification including carriage of materials within all leads, lifts and other incidental, and as per directions of Engineer-in-Charge. The rate is including Royality, Malkana, Octroi, Toll Tax, Sales tax, GST or any other taxes imposed by the Government.

Providing weep holes in brick masonry/stone masonry/plain reinforced concrete abutment, wing wall, return wall with 110mm (one hundred ten millimetres) diameters P.V.C. pipe extending through the full width of the structure with slope of 1(v):20(H) towards drawing face complete as per drawing and technical specifications Clause 614, 709, 1204.3.7 , as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST and any other taxes imposed by the Government.

Backfilling behind abutment, wing wall and return wall complete as per drawings & technical specification clause1204.3.8 (i) (Granular Material) , as per approved drawing, design and specification including carriage of materials within all leads, lifts and other incidental, and as per directions of Engineer-in-Charge. The rate is including Royality, Malkana, Octroi, Toll Tax, Sales tax, GST or any other taxes imposed by the Government.

Providing and fixing polythelene aluminum polythelene (PE- AL-PE) composite pressure pipe U.V. stabilized with carbon block confirming to I.S. 15450-2004 of Kitec for water supply including clamps at appropriate spacing, cutting fixing and making good the walls etcetera; but excluding the cost of fittings (Internal work), including filling the joints with approved adhesive complete including entire carriage of materials within all leads lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

1620 (20mm) twenty millimeter diameter pipe O.D. pipe

1620 (25mm) twenty five millimeter diameter pipe O.D. pipe

Providing and laying in trenches, galvanised mild steel tubes (medium grade), tube fittings complete as per H.P.P.W.D specifications, approved drawing, design, as per the entire satisfaction and direction of the Engineer-In-Charge iincluding entire carriage of materials within all leads lifts and other incidentals. The rate is inclusive, toll taxes, GST and any other taxes imposed by the

25mm ( Twenty five millimetres ) nominal bore

20mm ( Twenty millimetres ) nominal bore

Providing and placing water tank make P.V.C. SINTEX three layer having capacity of 1000 ( One thousand) liters each tank with necessary fittings including over flow pipe scour pipe etcetera and pads required for in let and out let ball valve with cover and locking arrangements complete in all respect within all leads, lifts of materials and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Making connection of galvanized mild steel distribution branch with galvanized mild steel main 20mm to 40nmm (Twenty milimetres to Forty milimetres)nominal bore by providing and fixing tees including cutting and threading the pipe complete including entire carriage of materials within all leads lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes light grade ISI marked of fenolex/vectus/price 4.6mm thick having pressure not less than 6kg /cm2 (six kilogramm per centimetre square) including fixing with approved adhesive etc. complete including entire carriage of materials within all leads lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

110mm (One hundred ten milimetres) diametres

75mm (Seventy milimetres) diametres

Providing and fixing cast iron P.V.C. holder bat clamps ISI marked of approved drawing i/c/ steel screw and rawl plug etc. including entire carriage of materials within all leads lifts and other incidentals

110mm (One hundred ten milimetres) diametres

75mm (Seventy milimetres) diametres

Providing and fixing P.V.C. I.S.I. marked plain bend of Finolex / Vectus / Prince including filling the joints with including fixing with approved adhesive within all leads, lifts of materials and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

110mm (One hundred ten milimetres) diametres

75mm (Seventy milimetres) diametres

Providing and fixing P.V.C. (polyvinyl chloride) Supreme/ Finolex/ Prince single equal branch plain tees Confirming to BIS-14735 (Fourteen thousnad seven hundred thirty five), ISI marked including fixing with approved adhesive etcetera complete within all leads lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

110mm (One hundred ten milimetres) diametres

75mm (Seventy milimetres) diametres

Providing and fixing PVC (polyvinyl chloride) double equal branch with oval access door, insertion rubber washer 3 mm (Three millimetres) thick bolts and nuts ISI marked of Supreme/ Finolex/ Prince complete including fixing with approved adhesive etcetera complete as per H.P.P.W.D specifications, approved drawing, design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

110mm (One hundred ten milimetres) diametres

75mm (Seventy milimetres) diametres

Providing and fixing P.V.C. Collar ISI marked of Finolex / Supreme / Prince including fixing with approved adhesive complete, within all leads, lifts of materials and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

110mm (One hundred ten milimetres) diametres (confirming to BIS-14735-99)

75mm (Seventy milimetres) diametres

Providing and fixing P.V.C. I.S.I. marked heal rest of Finolex / Supreme / Prince including filling the joints with including fixing with approved adhesive within all leads, lifts of materials and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

110mm (One hundred ten milimetres) diametres

75mm (Seventy milimetres) diametres

Providing and fixing P.V.C. I.S.I. marked cowl (confirming to BIS-14735-99) ISI marked of Finolex / Supreme / Prince including fixing with approved adhesive complete, within all leads, lifts of materials and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

110mm (One hundred ten milimetres) diametres (confirming to BIS-14735-99)

75mm (Seventy five milimetres) diametres (confirming to BIS-14735-99)

Providing and fixing PVC (polyvinyl chloride) plain “Y" junction Finolex / Supreme / Prince ISI marked including fixing with approved adhesive etcetera. complete as per H.P.P.W.D specifications, approved drawing, design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

110mm dia (One hundred ten millimetres) diametres

75mm dia (Seventy five millimetres) diametres

Providing and fixing 110 x 90mm (One hundred ten into Ninety milimetres) P.V.C. I.S.I. marked floor trap of Finolex / Supreme / Prince ISI marked (confirming to BIS-14735-99) of self cleaning design including with approved adhesive cost of cutting and making good walls and floors complete, within all leads, lifts of materials and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing vitreous china Cera / Hindware or equivalent wash down water closet squatting pan ( EUROPEON TYPE) size 58x44cm (fifty eight into forty four centimetres) (earth work, bed concrete, foot rest and trap to be measured and paid for separately) (EUROPEON SEAT SIZE 58x44 cm) ( Angle Indian Universal Closet ) (seat cover and jet spray to be measured and paid for separately) within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing PVC coloured/white with (dual flushing system) 10.00 Ltrs (Ten litres) capacity low level flushing cistern (Sleek Plus) Hindware/cera/Jaquar of star white / snow white shade with fittings such as lead valve less siphon, 15mm (Fifteen milimetres) nominal size PVC ball valve with polythene float, with flush buffor, unions and couplings for connection with inlet, outlet and over flow pipe, 40mm (Forty milimetres) diametres C.P. flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet (over flow pipe to be measured and paid for separately) within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing vitreous china pedestal of Cera / Hindware or equivalent 55x40x80cm (Fifty five into forty into eighty centimetres) with single hole for pillar tap with pedestal including C.I. or M.S. brackets, painted white including cutting holes and making good the same with pedestal but excluding fittings within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 550mmx400mm (Five hundred fifty into four hundred millimetres) vitreous China wash basin with single hole for pillar tap with C.I. or M.S. (Cast iron or mild steel) brackets painted white including cutting holes and making good the same but excluding fittings complete as per H.P.P.W.D specifications, approved drawing, design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing stainless steel kitchen sink size 610 x510 mm (six hundred ten into four hundred sixty millimetre) with bowl depth 200 mm (two hundred millimetre) of AMC unik / diamond approved standard ISI make with drain board and C.P. waste with C.I. or M.S. Brackets painted including cutting holes and making good the same but excluding fitting within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 32mm (Thirty two millimetres) nominal size diametres rubber plug for wash basin within all leads, lifts of materials and other incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 32mm dia (Thirty two millimetres) diametres M.I. union for wash basin or sink complete as per H.P.P.W.D specifications, approved drawing, design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 32mm (Thirty two millimetres) diametres C.P (chromium plated) brass waste and plug for glazed ware sinks, basins etcetera. with long screwed shank and fly nut and fixed to steel pipe including vulcanite plug, brass chain and stud complete as per H.P.P.W.D specifications, approved drawing, design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 32mm (Thirty two millimetres) diametres P.V.C. (polyvinyl chloride) / C.P (chromium plated) Jal/ESS ESS waste for wash basin or sink complete as per H.P.P.W.D specifications, approved drawing, design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals.he rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.t.

Providing and fixing 100mm (One hundred millimetres) diametres C.P. (Chromium plated) Grating ISI Marked IS No. 8934 (Eight thousand nine hundred thirty four) of Jal/ESS for gully floor or Nahni trap as per H.P.P.W.D specifications, approved drawing, design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing flat back 600x450mm (Six hundred into Four hundred fifty millimetres) beveled edge mirror of superior glass mounted on 6mm (Six millimetres) thick A.C. asbestos cement sheet or ply wood sheet and fixed to wooden plugs with C.P. (Chromium plated) brass screws and washers complete as per H.P.P.W.D specifications, approved drawing, design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals.The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 600mmx20mm (Six hundred millimetre into Twenty millimetres) C.P. (Chromium plated) ISI Marked IS No. 8934 (Eight thousand nine hundred thirty four) of Jal/ESS ESS brass Towel rail with C.P. (Chromium plated) brass brackets fixed to wooden plugs with C.P.(Chromium plated) brass screws complete as per H.P.P.W.D specifications, approved drawing, design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 600mmx120mm (Six hundred millimetres into One hundred twenty millimetres) glass shelf of ISI No. 8934 (Eight thousand nine hundred thirty four) of Jal/ESS ESS make brackets and guard rail fixed to wooden plugs with C.P.(Chromium plated) brass screws complete as per H.P.P.W.D specifications, approved drawing, design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing two hole basin mixing Faucet complete as per H.P.P.W.D specifications, approved drawing, design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing chromium plated brass soap dish with C.P.(chromium plated) Brass brackets fixed to wooden cleats with C.P. (chromium plated) Brass screws complete as per H.P.P.W.D specifications, approved drawing, design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 100mm dia (one hundred millimetres) diametres C.P. (chromium plated) Brass shower rose with 15mm (Fifteen millimetres) or 20mm (Twenty millimetres) inlet complete as per H.P.P.W.D specifications, approved drawing, design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 15mm dia (Fifteen millimetres) diametres nominal bore chromium plated brass (ISI marked No. 8934) (Eight thousand nine hundred thirty four) bib tap (superior or heavy type) Jall ESS ESS as per H.P.P.W.D specifications, approved drawing, design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 15mm dia (Fifteen millimetres) diametres C.P. ( chromium plated) brass pillar tap with capstan head Conforming to IS: 8934 (Eight thousand nine hundred thirty four) Jal/ESS ESS as per H.P.P.W.D specifications, approved drawing, design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 15mm dia (Fifteen millimetres) diametres C.P. (chromium plated) brass stop cock Conforming ISI Marked IS No. 8934 (Eight thousand nine hundred thirty four) Jal/ESS ESS as per H.P.P.W.D specifications, approved drawing, design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 15mm (Fifteen millimetres) nominal bore PVC (polyvinyl chloride) connection pipe with brass union 30/ 45cm (Thirty or Forty five Centimetres) length complete as per H.P.P.W.D specifications, approved drawing, design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing ( chromium plated) brass full way valve with wheel as per H.P.P.W.D specifications, approved drawing, design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

15mm (Fifteen millimetres) nominal bore

Providing and fixing 15mm (Fifteen milimetres) diametres C.P.brass angle valve without nuts of Continental series of Jaquar / Classik series of Hindware / Floral Series of Cera / Hindon series of Jal as per approved drawing and design directed by the Engineer-in-Charge within all leads, lifts of materials and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 15mm (Fifteen milimetres) nominal bore C.P. brass valve (Horizontal plunger) type High pressure with polythene plastic floats of Continental series of Jaquar / Classik series of Hindware / Floral Series of Cera / Hindon series of Jal within all leads, lifts of materials and other incidentals and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and Fixing Charomium plated 40mm (forty millimetres) dia steel pipe for grab bars at 78cm (seventy eight centimetres) height metres M.S. plate as per details at the position of the seat and Wash Basin complete within all leads, lifts of materials and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge.

Providing and fixing Black or white hollow type plastic seat and cover for wash down water closet with C.P. (Chromium plated) brass hinges and rubber buffers matching with shade of European W.C. pan complete as per H.P.P.W.D specifications, approved drawing, design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals.The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing C.P. jet spray of Continental series of Jaquar / Classik series of Hindware / Floral Series of Cera / Hindon series of Jal of approved quality and colour with one metre tube within all leads, lifts of materials and other incidentals and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 150mm (One hundred fifty millimetres) nominal bore/diametres (to level or slopes) and jointing with stiff mixture of cement mortar in the proporation of 1:1 (one cement isto one sand) glazed stone ware/ P.V.C. pipes grade A including testing of pipe and joints complete. as per H.P.P.W.D specifications, approved drawing, design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Construction of manhole with R.C.C. (Reinforced cement concrete) top slab in 1:2:4(One cement isto Two sand isto Four graded crushed stone aggregate 20mm(Twenty millimetres nominal size)mix foundation concrete 1:4:8(One cement isto Four sand isto Eight graded crushed/broken stone aggregate 40mm(Forty millimetres) nominal size inside plastering 15mm (Fifteen millimetres) thick with cement mortar 1:3 (One Cement isto three sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4(One cement isto Two sand isto Four graded crushed stone aggregate 20mm (Twenty millimetres) nominal size finished smooth complete including curing and testing inside size 800x800mm (Eight hundred into Eight hundred millimetres) and 500mm(Five hundred millimetres) deep, including C.I. (Cast iron) cover with frame (light duty single seal pattern -I) 455x610mm (Four hundred fifty five into six hundred ten millimetres) internal dimensions total weight of cover and frame to be not less than 38 Kgs (Thirty eight kilograms) weight of cover 23Kgs (Twenty three kilograms) and weight of frame 15 Kgs (Fifteen kilograms) with 300mm (Three hundred millimetres) thick walls of squared rubble masonry coursed with hard stone of approved quality in cement mortar 1:3 (one cement isto three sand) as per H.P.P.W.D specifications, approved drawing, design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Construction of manhole with R.C.C. (Reinforced cement concrete) top slab in 1:2:4(One cement: Two sand: Four graded crushed stone aggregate 20mm(Twenty millimetres nominal size) mix foundation concrete 1:4:8(One cement isto Four sand: Eight graded crushed/broken stone aggregate 40mm(Forty millimetres) nominal size inside plastering 15mm ( Fifteen millimetres) thick with cement mortar 1:3 ( One Cement isto three sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4(One cement isto Two sand isto Four graded crushed stone aggregate 20mm(Twenty millimetres) nominal size mix finished smooth complete including curing and testing inside size 800x800mm (Eight hundred into Eight hundred millimetres) and 1000 mm (One thousand millimetres) deep, including C.I.(Cast iron) cover with frame (light duty single seal pattern -I) 455x610mm (Four hundred fifty five into six hundred and ten millimetres) internal dimensions total weight of cover and frame to be not less than 38 Kgs (Thirty eight kilograms) weight of cover 23Kgs (twenty three kilograms) and weight of frame 15 Kgs (Fifteen kilograms) with 300mm (Three hundred millimetres) thick walls of squared rubble masonry coursed with hard stone of approved quality in cement mortar 1:3 (one cement isto three sand) as per H.P.P.W.D specifications, approved drawing, design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Constructing brick masonry chamber for under ground C.I. (Cast iron) inspection chamber and bends with common burnt clay building bricks in cement mortar 1:5(One cement isto Five sand) C.I. (cast iron) cover with frame(light duty) 355x610mm(Three hundred fifty five into Six hundred ten millimetres)internal dimensions total weight of cover and frame to be not less than 38Kgs (Thirty eight Kilograms) weight of cover 23 Kgs (twenty three kilograms)and weight of frame 15 Kgs (Fifteen kilograms) RCC (Reinforced cement concrete) top slab with 1:2:4 (One cement isto Two sand isto Four graded crushed stone aggregate 20mm (Twenty millimetres) nominal size mix foundation concrete 1:5:10 (One cement isto Five sand isto Ten graded crushed/broken stone aggregate 40mm(Forty millimetres nominal size) inside plaster 15mm ( Fifteen millimetres) thick with cement mortar 1:3 ( One Cement isto three sand) finished smooth with a floating coat of neat cement on walls and bed concrete etcetera. complete inside dimensions 455x610mmx450mm (Four hundred fifty five into Six hundred ten into Four hundred fifty millimetres) deep single pipe line as per H.P.P.W.D specifications, approved drawing, design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 150x100mm size square mouth stone ware gully trap grade-A complete with C.I. gratings brick masonry camber in cement mortar 1:5 within all leads, lifts of materials and other incidentals. as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and laying cement concrete 1:5:10 (One Cement isto Five Sand istoTen graded stone aggregate 40mm (Forty millimetres) nominal size 100mm ( One Hundred milimetre ) thickness bedding for upto 230mm (two hundred thirty millimetres) dia pipe including, necessary form work and curing complete as per H.P.P.W.D specifications, approved drawing, design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana and all type of taxes imposed by the Government.

Providing and fixing polythelene aluminum polythelene (PE- AL-PE) composit end seal compression fitting as per IS-15450 of Kitec / Supreme / Finolex for cold water supply e.g. tees, elbows, reduser,connceters,couplers and claps jointing testing and fitting complete including entire carriage of materials within all leads lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Equal Tee (1620)

Equal Tee (2025)

Female elbow (1620 X 20mm thread)

Female elbow (1620 X 20mm thread)

Female branch tee(1620x2025 x25 mm thread)

Female branch tee(1620x1620 x20 mm thread)

Male thread connecter (1620 X 20mm thread)

Male thread connecter (2025 X25mm thread)

Reducer 2025x1620

Coupler 1620

Coupler 2025

Harbhajan singh