Infrastructure Development of 14 Nos Model School in the State under Mission Shiksha flagship programme. SH Govt. Hr. Sec. School Boleng

Amount

SSH:- Renovation of SPT Building (4Unit)

Demolishing cement concrete 1 : 3 : 6 or richer mix including disposal off material within 50 metres lead.

Demolishing RCC work including stacking of steel bars and disposal of unserviceable materials within 50 metres lead.

Demolishing brick work in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 metres lead.

Dismantling wood work of sectional area below 40 Sq.cm. and above wrought, framed and fixed in frames, other frames and trusses including stacking the material within 50 m lead.

Dismantling doors, windows and clerestory windows (steel or wood) shutters including chowkhats, architrave, hold fasts etc complete and stcking within 50m lead. a) Of area 3 Sq.m. and below

Dismantling GI sheet roofing including ridges, hips, valleys and gutters etc and stacking the material within 50 m lead.

Dismantling cement, asbestos, celotax or other ceiling or partition hard board partition wall including stacking of serviceable materials and disposal of unserviceable materials within 50 m lead.

Earth work in excavation in foundation and trenches in soils containing 50% or more of shingle or small size boulders upto 30 cm size, lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning the stacked soil in 15 cm layers when required, into plinth, sides of foundation etc consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated soil as directed within a lead of 50m.

Re-filling excavated earth in foundations and plinth etc. in 15 cm layer including ramming and watering etc. complete.

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete.

Providing and laying in foundations and plinth cement concrete 1 : 5 : 10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering.

Providing and laying cement concrete 1 : 2 : 4 (1 cement : 2 coarse sand : 4 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering in : a) Foundations and plinth

Reinforcement cement concrete work in columns, pillars, piers, abutments, post and struts etc up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but exluding cost of centring, shuttering and reinforcement. c) 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete work in lintels, beams and bresumers up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centering, shuttering and reinforcement. b)1 : 1.5 : 3 (1 cement : 1.5coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete in suspended floors, roofs, landings and balconies upto floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring and shuttering and reinforcement with M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Centring and shuttering including strutting, propping etc and removal of form work for : a) Foundation, footings, bases of columns etc. and mass concrete.

b) Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc.

c) Suspended floors, roofs, landings shelves and their supports, balconies and chajjas (3.5 m height).

d) Lintels, beams, girders, bressumers and cantilevers etc.

e) Column, pillars, posts and struts etc.

Reinforcement of RCC work including bending, binding and placing in position complete. a)Tar/TMT Steel

Masonry with pre-cast cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand 6 graded stone aggregate 20 mm nominal size) blocks in cement mortar 1 : 3 (1 cement : 3 fine sand) in foundations and plinth.

Providing approved best available local wood (Class - B II) work in frames of doors, windows clerestory windows and other frames, wrought framed and fixed in position.

Providing best available local wood (Class - B II) work in frames of false ceiling, partitions and trusses etc, sawn and put up in position.

Providing and fixing panelled, glazed or panelled and glazed shutters for doors, windows and clerestory windows including necessary iron butt hinges with necessary screws. a) 38 mm thick best available local wood, class - B I

Providing and fixing 2.50 cm thick approved local wood eaves boards 23 cm wide with necessary mouldings etc.

Supplying and fixing Glass panes with wooden fillets including removal of broken glass panes and old wooden fillets wherever necessary but excluding cost of wooden fillets. a) Glass panes 3 mm thick and area 0.1 Sq.m. each

Supplying and fixing new wooden fillets wherever necessary. a) 1st class wood fillets

Providing and fixing MS grills of required pattern in wooden frames of windows etc with MS flat, square or round bars with round headed bolts and nuts or by screws. b) Ornamental grill.

Providing and fixing Iron T-hinges bright finished or and black enamelled with necessary screws etc complete. a) 300 x 115 x 2.24 mm

Providing and fixing MS door latch with necessary screws etc complete. a) 300 x 20 x 6 mm

Providing and fixing MS handles with necessary screws etc complete. a) 125 mm

Providing and fixing iron pressed butt hinges bright finished with necessary screws etc complete. a) 125 x 65 x 2.12 mm

c) 75 x 47 x 1.70 mm

Cement concrete flooring 1 : 2 : 4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement. c) 75 mm thick

Providing corrugated G.I.sheet roofing fixed with galvanised iron J or L hooks, bolts & nuts 8 mm dia with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead complete, excluding the cost of purlins, rafters and trusses. b) 0.63 mm thick GI sheet

Providing ridges or hips 60 cm overall in plain G.I. sheet fixed with galvanised iron J or L hooks, bolts and nuts 8 mm dia. G.I. limpet and bitumen washers complete. b) 0.63 mm thick GI sheet

Providing and fixing 12 mm thick insulating board ceiling of approved quality with necessary nails etc. complete (frame work to be paid separately).

Providing and fixing plain, square edged wooden beading 38 mm x 12 mm section with screws of approved quality for ceiling. a) Best local approved quality wood.

Extra for making chamfered edges of beading.

12 mm cement plaster 1 : 3 (1 cement : 3 fine sand).

Applying priming coat with ready mixed genuine red lead paint of approved brand and manufacture on steel work.

Applying priming coat with ready mixed pink primer of approved brand and manufacture on wood work complete.

Painting two or more coats (excluding priming coat) with superior ready mixed paint for wood work of approved brand and manufacture in all shades on new work to give an even shade.

Painting two or more coats on GI sheets with superior ready mixed paint of approved brand and manufacture in white, grey or green shades on new work to give an even shade.

Painting two or more coats (excluding priming coat) with superior ready mixed paint for steel work of approved brand and manufacture in all shades on new work to give an even shade.

Distempering with dry distemper of approved brand and manufacture (two or more coats) and of required shade on new work including priming coat of whiting to give an even shade.

Making plinth protection 50 mm thick of cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 stone aggregate using 20 mm nominal size) over 75 mm bed of stone ballast 40 mm nominal size well rammed and consolidated and grouted with fine sand including finsihing the top smooth

Construction of cement concrete drain 15 cm wide and 15 cm deep in cement concrete 1 : 3 : 6 (1 cement : 3 sand : 6 hard graded stone chips or shingle 40 mm and down gauge) 8 cm thick on sides and bottom and plastering and all exposed surfaces with 12 mm thick cement mortar 1 : 3 (1 cement : 3 coarse sand) including shuttering complete.

Loading and unloading of Cement & Steel by manual means and stacking

Cost of Haulage excluding loading & unloading a) Cement from Pasighat to Boleng (Lead - 92 Km) (Hill Road) Qnty as per TC

b) Steel from Pasighat to Boleng (Lead - 92.00 Km) (Hill Road) Qnty as per TC

Carriage of river bed materials from quarry to site of work

SSH:- Maintenance of Science Laboratories.

Demolishing cement concrete 1 : 3 : 6 or richer mix including disposal off material within 50 metres lead.

Dismantling wood work of sectional area below 40 Sq.cm. and above wrought, framed and fixed in frames, other frames and trusses including stacking the material within 50 m lead.

Dismantling doors, windows and clerestory windows (steel or wood) shutters including chowkhats, architrave, hold fasts etc complete and stcking within 50m lead. a) Of area 3 Sq.m. and below

Dismantling GI sheet roofing including ridges, hips, valleys and gutters etc and stacking the material within 50 m lead.

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 m lead.

Repairs to plaster in patches of 2.50 Sq.m. and under including cutting the patch to proper shape and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50 m lead. a) With cement mortar 1 : 4 (1 cement : 4 fine sand)

Providing approved best available local wood (Class - B II) work in frames of doors, windows clerestory windows and other frames, wrought framed and fixed in position.

Providing best available local wood (Class - B II) work in frames of false ceiling, partitions and trusses etc, sawn and put up in position.

Providing and fixing panelled, glazed or panelled and glazed shutters for doors, windows and clerestory windows including aluminium butt hinges with necessary screws. a) 38mm thick best available local wood class - B I

Providing and fixing 12 mm thick insulating board ceiling of approved quality with necessary nails etc. complete (frame work to be paid separately).

Supplying and fixing Glass panes with wooden fillets including removal of broken glass panes and old wooden fillets wherever necessary but excluding cost of wooden fillets. a) Glass panes 3 mm thick and area 0.1 Sq.m. each

Supplying and fixing new wooden fillets wherever necessary. a) 1st class wood fillets

Providing corrugated G.I.sheet roofing fixed with galvanised iron J or L hooks, bolts & nuts 8 mm dia with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead complete, excluding the cost of purlins, rafters and trusses. 0.63 mm thick GI sheet

Construction of cement concrete drain 15 cm wide and 15 cm deep in cement concrete 1 : 3 : 6 (1 cement : 3 sand : 6 hard graded stone chips or shingle 40 mm and down gauge) 8 cm thick on sides and bottom and plastering and all exposed surfaces with 12 mm thick cement mortar 1 : 3 (1 cement : 3 coarse sand) including shuttering complete.

Making plinth protection 50 mm thick of cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 stone aggregate using 20 mm nominal size) over 75 mm bed of stone ballast 40 mm nominal size well rammed and consolidated and grouted with fine sand including finsihing the top smooth.

25 mm thick cement concrete flooring 1 : 2 : 4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5 mm nominal size) finished with a floating coat of neat cement.

Distempering (one or more coats) with oil bound washable distemper of approved brand and manufacture and of required shade on old work to give an even shade. a) In two or more coats

Applying priming coat with ready mixed pink primer of approved brand and manufacture on wood work complete.

Painting two or more coats (excluding priming coat) with superior ready mixed paint for wood work of approved brand and manufacture in all shades on new work to give an even shade.

Painting one or more coats on GI sheets with ready mixed superior paint of approved brand and manufacture on old work to give an even shade.

Providing and fixing soft wood 'EVE' board 25 mm thick and 225 mm wide including painting two coats complete as directed.

Providing and fixing Iron T-hinges bright finished or and black enamelled with necessary screws etc complete. a) 300 x 115 x 2.24 mm

Providing and fixing MS door latch with necessary screws etc complete. a) 300 x 20 x 6 mm

Providing and fixing MS handles with necessary screws etc complete. a) 125 mm

Providing and fixing iron pressed butt hinges bright finished with necessary screws etc complete. a) 125 x 65 x 2.12 mm

c) 75 x 47 x 1.70 mm

Loading and unloading of Cement & Steel by manual means and stacking

Cost of Haulage excluding loading & unloading a) Cement from Pasighat to Boleng (Lead - 92 Km) (Hill Road) Qnty as per TC

b) Steel from Pasighat to Boleng (Lead - 92.00 Km) (Hill Road) Qnty as per TC

Carriage of river bed materials from quarry to site of work

(SSSH:- Equpment/ Apparatus required in Physics Laboratory )

Resonance of tube apparatus

Vernier Callipers (Stainless stell )

Screw gauge (Stainless stell )

Physical balance with weighing boxes

Metre scale

Spring balance with slotted weights each of 50 gram or 100 gram

Apparatus for the parallelogram law of forces

Beaker 250 ml

Beaker 50 ml

Sonometer (Complete set )

Plastic Bucket 10 set capacity

Plastic mugs

Ohm's law apparatus ( Complete set)

Carbon resistors of 50Ω

Carbon resistors of 100 Ω

Carbon resistors of 1000 Ω

Gold leaf Electroscope

Leclanche cell (Complete set )

Ammonium Chloride (NH4CI)

Optical bench 1 meter (Complete set )

Optical bench 1.5 meter (Complete set )

Lens with mirror holders i.e uprights

Travelling Microscope

Sand paper

Convex lenses of focal length 15/25 cm

Convex lenses of focal length 10 cm

Connecting wire DCC

Iron steel almirah for keeping articles

(SSSH:- Equpment/ Apparatus required in Biology Laboratory )

Permanent slide box for Botany

Permanent slide box for Zoology

Spirit fuel for lamp burner

Wire gauge with frame

Boric Acid

Potasium Nitrate

Magnesium Sulphate

Potasium iodide

Sudan III reagent

Osmic acid

Iodine solution

Dilute Hcl

Milions reagent

Glycerin

Benedict reagent

Biuret reagent

Fehling solution A

Fehling solution B

Dropper 8"

Scissor S/S 6"

Compound Microscope

(SSSH:- Equpment/ Apparatus required in Secondary Section Science Laboratory )

Beaker -50 ml

Beaker -100 ml

Beaker -500 ml

Funnel glass 2"

Funnel glass 3"

Funnel glass 4"

Measuring cylinder 100 ml

Measuring cylinder 250 ml

Measuring cylinder 500 ml

Pipette glass 10 ml

Test tube glass 15 x 125 mm

Test tube glass 15 x 150 mm

Plain slide

Test tube stand plastic

Cover slip

Petri dish 3 " dia

Pestle porceline and Mortar 3 "

Filter Paper 12.5 cm

PH Paper

Compound Microscope

Concave Mirror 50 mm dia F1 15/20 cm

Convex Mirror 50 mm dia F1 15/20 cm

Glass Prism 50 x 50 mm

Wash bowl

Centrifuge machine digital

Spirit Lamp brass

Tripod Stand 8"

Separating funnel 250 ml plastic

Chromatography paper

China Dish 3"

Distillation flask with condenser 250 ml

Stethoscope

Blood Pressure machine manual

Clinical Thermometer digital

Concave lens 50 mm

Convex lens 50 mm

Vernier Calliper "IME" type

Volumetric flask 250 ml

Weighing Scale ( Digital Electronic balalne 600gm ressolution O.oigm " Citizen " make

Watch glass 3" dia

Dropper glass 8"

Spring balance 1000gm

Magnifying glass 3" dia

Digital Incubators (14 x 14 x 14") SYMAX

Ammeter with Stand

Micrometer with Stand

Galvanometer 30-0-30 with stand

Resistor

Voltmeter with stand

Blotting paper

Bunsen Burner with stop cock

Bar Magnet

Battery Eliminator 2-12 volt

Hydrochloric acid

Sulphuric acid

Nitric acid

(SSSH:- Equpment/ Apparatus required in Geography Laboratory)

Map of Arunachal Pradesh (Both Physical & Political )

Map of North Eastern State (Both Physical & Political )

Map of Seven continents (Both Physical & Political )

Atlas ( Latest edition )

Globe 30cm dia

(SSh:- Principal office)

Earth work in excavation in foundation and trenches in soils containing 50% or more of shingle or small size boulders upto 30 cm size, lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning the stacked soil in 15 cm layers when required, into plinth, sides of foundation etc consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated soil as directed within a lead of 50m.

Re-filling excavated earth in foundations and plinth etc. in 15 cm layer including ramming and watering etc. complete.

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete.

Providing and laying in foundations and plinth cement concrete 1 : 5 : 10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering.

Providing and laying cement concrete 1 : 2 : 4 (1 cement : 2 coarse sand : 4 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering in : a) Foundations and plinth

Reinforcement cement concrete work in columns, pillars, piers, abutments, post and struts etc up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but exluding cost of centring, shuttering and reinforcement. c) 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete work in lintels, beams and bresumers up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centering, shuttering and reinforcement. b)1 : 1.5 : 3 (1 cement : 1.5coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete in suspended floors, roofs, landings and balconies upto floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring and shuttering and reinforcement with M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Centring and shuttering including strutting, propping etc and removal of form work for : a) Foundation, footings, bases of columns etc. and mass concrete.

b) Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc.

c) Suspended floors, roofs, landings shelves and their supports, balconies and chajjas (3.5 m height).

d) Lintels, beams, girders, bressumers and cantilevers etc.

e) Column, pillars, posts and struts etc.

Reinforcement of RCC work including bending, binding and placing in position complete. a)Tar/TMT Steel

Masonry with pre-cast cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand 6 graded stone aggregate 20 mm nominal size) blocks in cement mortar 1 : 3 (1 cement : 3 fine sand) in foundations and plinth.

Providing approved best available local wood (Class - B II) work in frames of doors, windows clerestory windows and other frames, wrought framed and fixed in position.

Providing best available local wood (Class - B II) work in frames of false ceiling, partitions and trusses etc, sawn and put up in position.

Providing and fixing panelled, glazed or panelled and glazed shutters for doors, windows and clerestory windows including necessary iron butt hinges with necessary screws. a) 38 mm thick best available local wood, class - B I

Providing and fixing 2.50 cm thick approved local wood eaves boards 23 cm wide with necessary mouldings etc.

Supplying and fixing Glass panes with wooden fillets including removal of broken glass panes and old wooden fillets wherever necessary but excluding cost of wooden fillets. a) Glass panes 3 mm thick and area 0.1 Sq.m. each

Supplying and fixing new wooden fillets wherever necessary. a) 1st class wood fillets

Providing and fixing MS grills of required pattern in wooden frames of windows etc with MS flat, square or round bars with round headed bolts and nuts or by screws. b) Ornamental grill.

Providing and fixing Iron T-hinges bright finished or and black enamelled with necessary screws etc complete. a) 300 x 115 x 2.24 mm

Providing and fixing MS door latch with necessary screws etc complete. a) 300 x 20 x 6 mm

Providing and fixing MS handles with necessary screws etc complete. a) 125 mm

Cement concrete flooring 1 : 2 : 4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement. c) 75 mm thick

Providing corrugated G.I.sheet roofing fixed with galvanised iron J or L hooks, bolts & nuts 8 mm dia with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead complete, excluding the cost of purlins, rafters and trusses. b) 0.63 mm thick GI sheet

Providing ridges or hips 60 cm overall in plain G.I. sheet fixed with galvanised iron J or L hooks, bolts and nuts 8 mm dia. G.I. limpet and bitumen washers complete. b) 0.63 mm thick GI sheet

Providing and fixing 12 mm thick insulating board ceiling of approved quality with necessary nails etc. complete (frame work to be paid separately).

Providing and fixing plain, square edged wooden beading 38 mm x 12 mm section with screws of approved quality for ceiling. a) Best local approved quality wood.

Extra for making chamfered edges of beading.

12 mm cement plaster 1 : 3 (1 cement : 3 fine sand).

Applying priming coat with ready mixed genuine red lead paint of approved brand and manufacture on steel work.

Applying priming coat with ready mixed pink primer of approved brand and manufacture on wood work complete.

Painting two or more coats (excluding priming coat) with superior ready mixed paint for wood work of approved brand and manufacture in all shades on new work to give an even shade.

Painting two or more coats on GI sheets with superior ready mixed paint of approved brand and manufacture in white, grey or green shades on new work to give an even shade.

Painting two or more coats (excluding priming coat) with superior ready mixed paint for steel work of approved brand and manufacture in all shades on new work to give an even shade.

Distempering with dry distemper of approved brand and manufacture (two or more coats) and of required shade on new work including priming coat of whiting to give an even shade.

Making plinth protection 50 mm thick of cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 stone aggregate using 20 mm nominal size) over 75 mm bed of stone ballast 40 mm nominal size well rammed and consolidated and grouted with fine sand including finsihing the top smooth

Construction of cement concrete drain 15 cm wide and 15 cm deep in cement concrete 1 : 3 : 6 (1 cement : 3 sand : 6 hard graded stone chips or shingle 40 mm and down gauge) 8 cm thick on sides and bottom and plastering and all exposed surfaces with 12 mm thick cement mortar 1 : 3 (1 cement : 3 coarse sand) including shuttering complete.

Loading and unloading of Cement & Steel by manual means and stacking

Cost of Haulage excluding loading & unloading a) Cement from Pasighat to Boleng (Lead - 92 Km) (Hill Road) Qnty as per TC

b) Steel from Pasighat to Boleng (Lead - 92.00 Km) (Hill Road) Qnty as per TC

Carriage of river bed materials from quarry to site of work

(SSH:- Smart Class room )

Earth work in excavation in foundation and trenches in soils containing 50% or more of shingle or small size boulders upto 30 cm size, lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning the stacked soil in 15 cm layers when required, into plinth, sides of foundation etc consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated soil as directed within a lead of 50m.

Re-filling excavated earth in foundations and plinth etc. in 15 cm layer including ramming and watering etc. complete.

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete.

Providing and laying in foundations and plinth cement concrete 1 : 5 : 10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering.

Providing and laying cement concrete 1 : 2 : 4 (1 cement : 2 coarse sand : 4 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering in : a) Foundations and plinth

Reinforcement cement concrete work in columns, pillars, piers, abutments, post and struts etc up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but exluding cost of centring, shuttering and reinforcement. c) 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete work in lintels, beams and bresumers up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centering, shuttering and reinforcement. b)1 : 1.5 : 3 (1 cement : 1.5coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete in suspended floors, roofs, landings and balconies upto floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring and shuttering and reinforcement with M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Centring and shuttering including strutting, propping etc and removal of form work for : a) Foundation, footings, bases of columns etc. and mass concrete.

b) Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc.

c) Suspended floors, roofs, landings shelves and their supports, balconies and chajjas (3.5 m height).

d) Lintels, beams, girders, bressumers and cantilevers etc.

e) Column, pillars, posts and struts etc.

Reinforcement of RCC work including bending, binding and placing in position complete. a)Tar/TMT Steel

Masonry with pre-cast cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand 6 graded stone aggregate 20 mm nominal size) blocks in cement mortar 1 : 3 (1 cement : 3 fine sand) in foundations and plinth.

Providing approved best available local wood (Class - B II) work in frames of doors, windows clerestory windows and other frames, wrought framed and fixed in position.

Providing best available local wood (Class - B II) work in frames of false ceiling, partitions and trusses etc, sawn and put up in position.

Providing and fixing panelled, glazed or panelled and glazed shutters for doors, windows and clerestory windows including necessary iron butt hinges with necessary screws. a) 38 mm thick best available local wood, class - B I

Providing and fixing 2.50 cm thick approved local wood eaves boards 23 cm wide with necessary mouldings etc.

Supplying and fixing Glass panes with wooden fillets including removal of broken glass panes and old wooden fillets wherever necessary but excluding cost of wooden fillets. a) Glass panes 3 mm thick and area 0.1 Sq.m. each

Supplying and fixing new wooden fillets wherever necessary. a) 1st class wood fillets

Providing and fixing MS grills of required pattern in wooden frames of windows etc with MS flat, square or round bars with round headed bolts and nuts or by screws. b) Ornamental grill.

Providing and fixing Iron T-hinges bright finished or and black enamelled with necessary screws etc complete. a) 300 x 115 x 2.24 mm

Providing and fixing MS door latch with necessary screws etc complete. a) 300 x 20 x 6 mm

Providing and fixing MS handles with necessary screws etc complete. a) 125 mm

Cement concrete flooring 1 : 2 : 4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement. c) 75 mm thick

Providing corrugated G.I.sheet roofing fixed with galvanised iron J or L hooks, bolts & nuts 8 mm dia with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead complete, excluding the cost of purlins, rafters and trusses. b) 0.63 mm thick GI sheet

Providing ridges or hips 60 cm overall in plain G.I. sheet fixed with galvanised iron J or L hooks, bolts and nuts 8 mm dia. G.I. limpet and bitumen washers complete. b) 0.63 mm thick GI sheet

Providing and fixing 12 mm thick insulating board ceiling of approved quality with necessary nails etc. complete (frame work to be paid separately).

Providing and fixing plain, square edged wooden beading 38 mm x 12 mm section with screws of approved quality for ceiling. a) Best local approved quality wood.

Extra for making chamfered edges of beading.

12 mm cement plaster 1 : 3 (1 cement : 3 fine sand).

Applying priming coat with ready mixed genuine red lead paint of approved brand and manufacture on steel work.

Applying priming coat with ready mixed pink primer of approved brand and manufacture on wood work complete.

Painting two or more coats (excluding priming coat) with superior ready mixed paint for wood work of approved brand and manufacture in all shades on new work to give an even shade.

Painting two or more coats on GI sheets with superior ready mixed paint of approved brand and manufacture in white, grey or green shades on new work to give an even shade.

Painting two or more coats (excluding priming coat) with superior ready mixed paint for steel work of approved brand and manufacture in all shades on new work to give an even shade.

Distempering with dry distemper of approved brand and manufacture (two or more coats) and of required shade on new work including priming coat of whiting to give an even shade.

Making plinth protection 50 mm thick of cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 stone aggregate using 20 mm nominal size) over 75 mm bed of stone ballast 40 mm nominal size well rammed and consolidated and grouted with fine sand including finsihing the top smooth

Construction of cement concrete drain 15 cm wide and 15 cm deep in cement concrete 1 : 3 : 6 (1 cement : 3 sand : 6 hard graded stone chips or shingle 40 mm and down gauge) 8 cm thick on sides and bottom and plastering and all exposed surfaces with 12 mm thick cement mortar 1 : 3 (1 cement : 3 coarse sand) including shuttering complete.

Loading and unloading of Cement & Steel by manual means and stacking

Cost of Haulage excluding loading & unloading a) Cement from Pasighat to Boleng (Lead - 92 Km) (Hill Road) Qnty as per TC

b) Steel from Pasighat to Boleng (Lead - 92.00 Km) (Hill Road) Qnty as per TC

Carriage of river bed materials from quarry to site of work

(SSh:- Renovation and Extention of Computer class)

Demolishing cement concrete 1 : 3 : 6 or richer mix including disposal off material within 50 metres lead.

Earth work in excavation in foundation and trenches in soils containing 50% or more of shingle or small size boulders upto 30 cm size, lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning the stacked soil in 15 cm layers when required, into plinth, sides of foundation etc consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated soil as directed within a lead of 50m.

Re-filling excavated earth in foundations and plinth etc. in 15 cm layer including ramming and watering etc. complete.

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete.

Providing and laying in foundations and plinth cement concrete 1 : 5 : 10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering.

Providing and laying cement concrete 1 : 2 : 4 (1 cement : 2 coarse sand : 4 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering in : a) Foundations and plinth

Reinforcement cement concrete work in columns, pillars, piers, abutments, post and struts etc up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but exluding cost of centring, shuttering and reinforcement. c) 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete work in lintels, beams and bresumers up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centering, shuttering and reinforcement. b)1 : 1.5 : 3 (1 cement : 1.5coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete in suspended floors, roofs, landings and balconies upto floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring and shuttering and reinforcement with M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Centring and shuttering including strutting, propping etc and removal of form work for : a) Foundation, footings, bases of columns etc. and mass concrete.

b) Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc.

c) Suspended floors, roofs, landings shelves and their supports, balconies and chajjas (3.5 m height).

d) Lintels, beams, girders, bressumers and cantilevers etc.

e) Column, pillars, posts and struts etc.

Reinforcement of RCC work including bending, binding and placing in position complete. a)Tar/TMT Steel

Masonry with pre-cast cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand 6 graded stone aggregate 20 mm nominal size) blocks in cement mortar 1 : 3 (1 cement : 3 fine sand) in foundations and plinth.

Providing approved best available local wood (Class - B II) work in frames of doors, windows clerestory windows and other frames, wrought framed and fixed in position.

Providing best available local wood (Class - B II) work in frames of false ceiling, partitions and trusses etc, sawn and put up in position.

Providing and fixing panelled, glazed or panelled and glazed shutters for doors, windows and clerestory windows including necessary iron butt hinges with necessary screws. a) 38 mm thick best available local wood, class - B I

Providing and fixing 2.50 cm thick approved local wood eaves boards 23 cm wide with necessary mouldings etc.

Supplying and fixing Glass panes with wooden fillets including removal of broken glass panes and old wooden fillets wherever necessary but excluding cost of wooden fillets. a) Glass panes 3 mm thick and area 0.1 Sq.m. each

Supplying and fixing new wooden fillets wherever necessary. a) 1st class wood fillets

Providing and fixing MS grills of required pattern in wooden frames of windows etc with MS flat, square or round bars with round headed bolts and nuts or by screws. b) Ornamental grill.

Providing and fixing Iron T-hinges bright finished or and black enamelled with necessary screws etc complete. a) 300 x 115 x 2.24 mm

Providing and fixing MS door latch with necessary screws etc complete. a) 300 x 20 x 6 mm

Providing and fixing MS handles with necessary screws etc complete. a) 125 mm

Cement concrete flooring 1 : 2 : 4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement. c) 75 mm thick

Providing corrugated G.I.sheet roofing fixed with galvanised iron J or L hooks, bolts & nuts 8 mm dia with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead complete, excluding the cost of purlins, rafters and trusses. b) 0.63 mm thick GI sheet

Providing ridges or hips 60 cm overall in plain G.I. sheet fixed with galvanised iron J or L hooks, bolts and nuts 8 mm dia. G.I. limpet and bitumen washers complete. b) 0.63 mm thick GI sheet

Providing and fixing 12 mm thick insulating board ceiling of approved quality with necessary nails etc. complete (frame work to be paid separately).

Providing and fixing plain, square edged wooden beading 38 mm x 12 mm section with screws of approved quality for ceiling. a) Best local approved quality wood.

Extra for making chamfered edges of beading.

12 mm cement plaster 1 : 3 (1 cement : 3 fine sand).

Applying priming coat with ready mixed genuine red lead paint of approved brand and manufacture on steel work.

Applying priming coat with ready mixed pink primer of approved brand and manufacture on wood work complete.

Painting two or more coats (excluding priming coat) with superior ready mixed paint for wood work of approved brand and manufacture in all shades on new work to give an even shade.

Painting two or more coats on GI sheets with superior ready mixed paint of approved brand and manufacture in white, grey or green shades on new work to give an even shade.

Painting two or more coats (excluding priming coat) with superior ready mixed paint for steel work of approved brand and manufacture in all shades on new work to give an even shade.

Distempering with dry distemper of approved brand and manufacture (two or more coats) and of required shade on new work including priming coat of whiting to give an even shade.

Making plinth protection 50 mm thick of cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 stone aggregate using 20 mm nominal size) over 75 mm bed of stone ballast 40 mm nominal size well rammed and consolidated and grouted with fine sand including finsihing the top smooth

Construction of cement concrete drain 15 cm wide and 15 cm deep in cement concrete 1 : 3 : 6 (1 cement : 3 sand : 6 hard graded stone chips or shingle 40 mm and down gauge) 8 cm thick on sides and bottom and plastering and all exposed surfaces with 12 mm thick cement mortar 1 : 3 (1 cement : 3 coarse sand) including shuttering complete.

Loading and unloading of Cement & Steel by manual means and stacking

Cost of Haulage excluding loading & unloading a) Cement from Pasighat to Boleng (Lead - 92 Km) (Hill Road) Qnty as per TC

b) Steel from Pasighat to Boleng (Lead - 92.00 Km) (Hill Road) Qnty as per TC

Carriage of river bed materials from quarry to site of work

(SSh:- Boys Toilet)

Earth work in excavation in foundation and trenches in soils containing 50% or more of shingle or small size boulders upto 30 cm size, lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning the stacked soil in 15 cm layers when required, into plinth, sides of foundation etc consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated soil as directed within a lead of 50m.

Re-filling excavated earth in foundations and plinth etc. in 15 cm layer including ramming and watering etc. complete.

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete.

Providing and laying in foundations and plinth cement concrete 1 : 5 : 10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering.

Providing and laying cement concrete 1 : 2 : 4 (1 cement : 2 coarse sand : 4 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering in : a) Foundations and plinth

Reinforcement cement concrete work in columns, pillars, piers, abutments, post and struts etc up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but exluding cost of centring, shuttering and reinforcement. c) 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete work in lintels, beams and bresumers up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centering, shuttering and reinforcement. b)1 : 1.5 : 3 (1 cement : 1.5coarse sand : 3 stone aggregate 20 mm nominal size).

Centring and shuttering including strutting, propping etc and removal of form work for : a) Foundation, footings, bases of columns etc. and mass concrete.

b) Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc.

d) Lintels, beams, girders, bressumers and cantilevers etc.

e) Column, pillars, posts and struts etc.

Reinforcement of RCC work including bending, binding and placing in position complete. a)Tar/TMT Steel

Masonry with pre-cast cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand 6 graded stone aggregate 20 mm nominal size) blocks in cement mortar 1 : 3 (1 cement : 3 fine sand) in foundations and plinth.

Providing approved best available local wood (Class - B II) work in frames of doors, windows clerestory windows and other frames, wrought framed and fixed in position.

Providing best available local wood (Class - B II) work in frames of false ceiling, partitions and trusses etc, sawn and put up in position.

Providing and fixing panelled, glazed or panelled and glazed shutters for doors, windows and clerestory windows including necessary iron butt hinges with necessary screws. a) 38 mm thick best available local wood, class - B I

Providing and fixing 2.50 cm thick approved local wood eaves boards 23 cm wide with necessary mouldings etc.

Providing and fixing Iron T-hinges bright finished or and black enamelled with necessary screws etc complete. a) 300 x 115 x 2.24 mm

Providing and fixing iron pressed butt hinges bright finished with necessary screws etc complete. a) 125 x 65 x 2.12 mm

Providing and fixing MS handles with necessary screws etc complete. a) 125 mm

Cement concrete flooring 1 : 2 : 4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement. c) 75 mm thick

Providing corrugated G.I.sheet roofing fixed with galvanised iron J or L hooks, bolts & nuts 8 mm dia with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead complete, excluding the cost of purlins, rafters and trusses. b) 0.63 mm thick GI sheet

Providing and fixing 12 mm thick insulating board ceiling of approved quality with necessary nails etc. complete (frame work to be paid separately).

Providing and fixing plain, square edged wooden beading 38 mm x 12 mm section with screws of approved quality for ceiling. a) Best local approved quality wood.

Extra for making chamfered edges of beading.

12 mm cement plaster 1 : 3 (1 cement : 3 fine sand).

Applying priming coat with ready mixed pink primer of approved brand and manufacture on wood work complete.

Painting two or more coats (excluding priming coat) with superior ready mixed paint for wood work of approved brand and manufacture in all shades on new work to give an even shade.

Painting two or more coats on GI sheets with superior ready mixed paint of approved brand and manufacture in white, grey or green shades on new work to give an even shade.

Distempering with dry distemper of approved brand and manufacture (two or more coats) and of required shade on new work including priming coat of whiting to give an even shade.

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x430x265 mm sizes respectively with CI automatic flushing cistern with fittings, RS or CI brackets standard size galvanized steel flush pipe and spreaders with brass unions and GI clamps complete including painting of cistern and fittings, cutting and making good the walls and floors where required. a) One urinal basin with 5 Litres CI automatic flushing cistern

Providing and fixing white vitreous china water closet squating pan (Indian type WC pan) size 580 mm with 100 mm and sand cast iron P or S trap, 12.5 Litre high level CI flushing cistern (of approved make) with fittings RS or CI brackets, 32 mm dia galvanized steel telescopic flush pipe with fittings and clamps 20 mm GI over flow pipe with specials and mosquito proof coupling of approved municipal design and GI chain and pull complete including painting of cistern and fittings, cutting and making good the walls and floors where required. a) Long Pan patten WC Pan

Making plinth protection 50 mm thick of cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 stone aggregate using 20 mm nominal size) over 75 mm bed of stone ballast 40 mm nominal size well rammed and consolidated and grouted with fine sand including finsihing the top smooth

Construction of cement concrete drain 15 cm wide and 15 cm deep in cement concrete 1 : 3 : 6 (1 cement : 3 sand : 6 hard graded stone chips or shingle 40 mm and down gauge) 8 cm thick on sides and bottom and plastering and all exposed surfaces with 12 mm thick cement mortar 1 : 3 (1 cement : 3 coarse sand) including shuttering complete.

Loading and unloading of Cement & Steel by manual means and stacking

Cost of Haulage excluding loading & unloading a) Cement from Pasighat to Boleng (Lead - 92 Km) (Hill Road) Qnty as per TC

b) Steel from Pasighat to Boleng (Lead - 92.00 Km) (Hill Road) Qnty as per TC

Carriage of river bed materials from quarry to site of work

(SSH:- Maintenance girls hostel)

Demolishing cement concrete 1 : 3 : 6 or richer mix including disposal off material within 50 metres lead.

Dismantling wood work of sectional area below 40 Sq.cm. and above wrought, framed and fixed in frames, other frames and trusses including stacking the material within 50 m lead.

Dismantling doors, windows and clerestory windows (steel or wood) shutters including chowkhats, architrave, hold fasts etc complete and stcking within 50m lead. a) Of area 3 Sq.m. and below

Dismantling GI sheet roofing including ridges, hips, valleys and gutters etc and stacking the material within 50 m lead.

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 m lead.

Repairs to plaster in patches of 2.50 Sq.m. and under including cutting the patch to proper shape and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50 m lead. a) With cement mortar 1 : 4 (1 cement : 4 fine sand)

Providing approved best available local wood (Class - B II) work in frames of doors, windows clerestory windows and other frames, wrought framed and fixed in position.

Providing best available local wood (Class - B II) work in frames of false ceiling, partitions and trusses etc, sawn and put up in position.

Providing and fixing panelled, glazed or panelled and glazed shutters for doors, windows and clerestory windows including aluminium butt hinges with necessary screws. a) 38mm thick best available local wood class - B I

Providing and fixing 12 mm thick insulating board ceiling of approved quality with necessary nails etc. complete (frame work to be paid separately).

Supplying and fixing Glass panes with wooden fillets including removal of broken glass panes and old wooden fillets wherever necessary but excluding cost of wooden fillets. a) Glass panes 3 mm thick and area 0.1 Sq.m. each

Supplying and fixing new wooden fillets wherever necessary. a) 1st class wood fillets

Providing corrugated G.I.sheet roofing fixed with galvanised iron J or L hooks, bolts & nuts 8 mm dia with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead complete, excluding the cost of purlins, rafters and trusses. a) 0.63 mm thick GI sheet

Construction of cement concrete drain 15 cm wide and 15 cm deep in cement concrete 1 : 3 : 6 (1 cement : 3 sand : 6 hard graded stone chips or shingle 40 mm and down gauge) 8 cm thick on sides and bottom and plastering and all exposed surfaces with 12 mm thick cement mortar 1 : 3 (1 cement : 3 coarse sand) including shuttering complete.

Making plinth protection 50 mm thick of cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 stone aggregate using 20 mm nominal size) over 75 mm bed of stone ballast 40 mm nominal size well rammed and consolidated and grouted with fine sand including finsihing the top smooth.

25 mm thick cement concrete flooring 1 : 2 : 4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5 mm nominal size) finished with a floating coat of neat cement.

Distempering (one or more coats) with oil bound washable distemper of approved brand and manufacture and of required shade on old work to give an even shade. a) In two or more coats

Applying priming coat with ready mixed pink primer of approved brand and manufacture on wood work complete.

Painting two or more coats (excluding priming coat) with superior ready mixed paint for wood work of approved brand and manufacture in all shades on new work to give an even shade.

Painting one or more coats on GI sheets with ready mixed superior paint of approved brand and manufacture on old work to give an even shade.

Painting one or more coats with superior quality ready mixed paint for steel work of approved brand and manufacture in all shades on old work to give an even shade.

Providing and fixing white vitreous china water closet squating pan (Indian type WC pan) size 580 mm with 100 mm and sand cast iron P or S trap, 12.5 Litre high level CI flushing cistern (of approved make) with fittings RS or CI brackets, 32 mm dia galvanized steel telescopic flush pipe with fittings and clamps 20 mm GI over flow pipe with specials and mosquito proof coupling of approved municipal design and GI chain and pull complete including painting of cistern and fittings, cutting and making good the walls and floors where required. a) Long Pan patten WC Pan

Providing and fixing GI pipes complete with GI fittings including trenching and refilling etc (external work). a) 20 mm nominal bore

Providing and fixing GI pipes complete with GI fittings and clamps including cutting and making good the walls (internal work). a) 15 mm nominal bore

b) 20 mm nominal bore

Providing and fixing brass bib cock of approved quality. a) 15 mm nominal bore

Providing and fixing soft wood 'EVE' board 25 mm thick and 225 mm wide including painting two coats complete as directed.

Providing and fixing Iron T-hinges bright finished or and black enamelled with necessary screws etc complete. a) 300 x 115 x 2.24 mm

Providing and fixing MS door latch with necessary screws etc complete. a) 300 x 20 x 6 mm

Providing and fixing MS handles with necessary screws etc complete. a) 125 mm

Loading and unloading of Cement & Steel by manual means and stacking

Cost of Haulage excluding loading & unloading a) Cement from Pasighat to Boleng (Lead - 92 Km) (Hill Road) Qnty as per TC

b) Steel from Pasighat to Boleng (Lead - 92.00 Km) (Hill Road) Qnty as per TC

Carriage of river bed materials from quarry to site of work

(SSH:- Maintenance of Teachers Quarter (Ty-II, 12 unit))

Demolishing cement concrete 1 : 3 : 6 or richer mix including disposal off material within 50 metres lead.

Dismantling wood work of sectional area below 40 Sq.cm. and above wrought, framed and fixed in frames, other frames and trusses including stacking the material within 50 m lead.

Dismantling doors, windows and clerestory windows (steel or wood) shutters including chowkhats, architrave, hold fasts etc complete and stcking within 50m lead. a) Of area 3 Sq.m. and below

Dismantling GI sheet roofing including ridges, hips, valleys and gutters etc and stacking the material within 50 m lead.

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 m lead.

Repairs to plaster in patches of 2.50 Sq.m. and under including cutting the patch to proper shape and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50 m lead. a) With cement mortar 1 : 4 (1 cement : 4 fine sand)

Providing approved best available local wood (Class - B II) work in frames of doors, windows clerestory windows and other frames, wrought framed and fixed in position.

Providing best available local wood (Class - B II) work in frames of false ceiling, partitions and trusses etc, sawn and put up in position.

Providing and fixing panelled, glazed or panelled and glazed shutters for doors, windows and clerestory windows including aluminium butt hinges with necessary screws. a) 38mm thick best available local wood class - B I

Providing and fixing 12 mm thick insulating board ceiling of approved quality with necessary nails etc. complete (frame work to be paid separately).

Supplying and fixing Glass panes with wooden fillets including removal of broken glass panes and old wooden fillets wherever necessary but excluding cost of wooden fillets. a) Glass panes 3 mm thick and area 0.1 Sq.m. each

Supplying and fixing new wooden fillets wherever necessary. a) 1st class wood fillets

Providing corrugated G.I.sheet roofing fixed with galvanised iron J or L hooks, bolts & nuts 8 mm dia with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead complete, excluding the cost of purlins, rafters and trusses. a) 0.63 mm thick GI sheet

Providing and laying cement concrete 1 : 2 : 4 (1 cement : 2 coarse sand : 4 stone aggregate 20 mm nominal size) excluding the cost of centring and shuttering in : Foundations and plinth

Construction of cement concrete drain 15 cm wide and 15 cm deep in cement concrete 1 : 3 : 6 (1 cement : 3 sand : 6 hard graded stone chips or shingle 40 mm and down gauge) 8 cm thick on sides and bottom and plastering and all exposed surfaces with 12 mm thick cement mortar 1 : 3 (1 cement : 3 coarse sand) including shuttering complete.

Making plinth protection 50 mm thick of cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 stone aggregate using 20 mm nominal size) over 75 mm bed of stone ballast 40 mm nominal size well rammed and consolidated and grouted with fine sand including finsihing the top smooth.

Cement concrete flooring 1 : 2 : 4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement. c) 75 mm thick

Distempering (one or more coats) with oil bound washable distemper of approved brand and manufacture and of required shade on old work to give an even shade. a) In two or more coats

Applying priming coat with ready mixed pink primer of approved brand and manufacture on wood work complete.

Painting two or more coats (excluding priming coat) with superior ready mixed paint for wood work of approved brand and manufacture in all shades on new work to give an even shade.

Painting one or more coats on GI sheets with ready mixed superior paint of approved brand and manufacture on old work to give an even shade.

Providing and fixing soft wood 'EVE' board 25 mm thick and 225 mm wide including painting two coats complete as directed.

Providing and fixing Iron T-hinges bright finished or and black enamelled with necessary screws etc complete. a) 300 x 115 x 2.24 mm

Providing and fixing MS door latch with necessary screws etc complete. a) 300 x 20 x 6 mm

Providing and fixing MS handles with necessary screws etc complete. a) 125 mm

(SH:- Septic tank )

Earth work in excavation in foundation and trenches in soils containing 50% or more of shingle or small size boulders upto 30 cm size, lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning the stacked soil in 15 cm layers when required, into plinth, sides of foundation etc consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated soil as directed within a lead of 50m.

Providing and laying in foundations and plinth cement concrete 1 : 4 : 8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering.

Reinforced concrete work in foundations, footings, bases of columns etc. and mass concrete excluding cost of centring, shuttering and reinforcement in : a) 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete in walls (any thickness) including attached pillasters, buttresses, plinth and string course, fillets etc from top of foundation up to floor two level including finishing and plastering the exposed surfaces with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface excluding cost of centring, shuttering and reinforcement in : a) 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete in suspended floors, roofs, landings and balconies upto floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring and shuttering and reinforcement with 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3stone aggregate 20 mm nominal size).

Centring and shuttering including strutting, propping etc and removal of form work for : b)Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc.

c)Suspended floors, roofs,landings shelves and their supports, balconies and chajjas (3.5m height).

Reinforcement of RCC work including bending, binding and placing in position complete. a) Tar/TMT Steel

15 mm cement plaster 1 : 3 (1 cement : 3 fine sand) on the rough side of single or half brick wall.

Construction of soak pit 1.2 x 1.1 x 1.2 m filled with brick bats including SW drain pipe 100 mm dia and 1.20 m long complete as per standard design.

Loading and unloading of Cement & Steel by manual means and stacking

Cost of Haulage excluding loading & unloading a) Cement from Pasighat to Boleng (Lead - 92 Km) (Hill Road) Qnty as per TC

b) Steel from Pasighat to Boleng (Lead - 92.00 Km) (Hill Road) Qnty as per TC

Carriage of river bed materials from quarry to site of work

(SSH:- Maintenance of Ty-I 3Unit)

Demolishing cement concrete 1 : 3 : 6 or richer mix including disposal off material within 50 metres lead.

Dismantling wood work of sectional area below 40 Sq.cm. and above wrought, framed and fixed in frames, other frames and trusses including stacking the material within 50 m lead.

Dismantling doors, windows and clerestory windows (steel or wood) shutters including chowkhats, architrave, hold fasts etc complete and stcking within 50m lead. a) Of area 3 Sq.m. and below

Dismantling GI sheet roofing including ridges, hips, valleys and gutters etc and stacking the material within 50 m lead.

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 m lead.

Repairs to plaster in patches of 2.50 Sq.m. and under including cutting the patch to proper shape and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50 m lead. a) With cement mortar 1 : 4 (1 cement : 4 fine sand)

Providing approved best available local wood (Class - B II) work in frames of doors, windows clerestory windows and other frames, wrought framed and fixed in position.

Providing best available local wood (Class - B II) work in frames of false ceiling, partitions and trusses etc, sawn and put up in position.

Providing and fixing panelled, glazed or panelled and glazed shutters for doors, windows and clerestory windows including aluminium butt hinges with necessary screws. a) 38mm thick best available local wood class - B I

Providing and fixing 12 mm thick insulating board ceiling of approved quality with necessary nails etc. complete (frame work to be paid separately).

Supplying and fixing Glass panes with wooden fillets including removal of broken glass panes and old wooden fillets wherever necessary but excluding cost of wooden fillets. a) Glass panes 3 mm thick and area 0.1 Sq.m. each

Supplying and fixing new wooden fillets wherever necessary. a) 1st class wood fillets

Providing corrugated G.I.sheet roofing fixed with galvanised iron J or L hooks, bolts & nuts 8 mm dia with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead complete, excluding the cost of purlins, rafters and trusses. 0.63 mm thick GI sheet

Construction of cement concrete drain 15 cm wide and 15 cm deep in cement concrete 1 : 3 : 6 (1 cement : 3 sand : 6 hard graded stone chips or shingle 40 mm and down gauge) 8 cm thick on sides and bottom and plastering and all exposed surfaces with 12 mm thick cement mortar 1 : 3 (1 cement : 3 coarse sand) including shuttering complete.

Making plinth protection 50 mm thick of cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 stone aggregate using 20 mm nominal size) over 75 mm bed of stone ballast 40 mm nominal size well rammed and consolidated and grouted with fine sand including finsihing the top smooth.

Cement concrete flooring 1 : 2 : 4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement. c) 75 mm thick

Distempering (one or more coats) with oil bound washable distemper of approved brand and manufacture and of required shade on old work to give an even shade. a) In two or more coats

Applying priming coat with ready mixed pink primer of approved brand and manufacture on wood work complete.

Painting two or more coats (excluding priming coat) with superior ready mixed paint for wood work of approved brand and manufacture in all shades on new work to give an even shade.

Providing and fixing Iron T-hinges bright finished or and black enamelled with necessary screws etc complete. a) 300 x 115 x 2.24 mm

Providing and fixing MS door latch with necessary screws etc complete. a) 300 x 20 x 6 mm

Providing and fixing MS handles with necessary screws etc complete. a) 125 mm

Providing and laying cement concrete 1 : 2 : 4 (1 cement : 2 coarse sand : 4 stone aggregate 20 mm nominal size) excluding the cost of centring and shuttering in : Foundations and plinth

Loading and unloading of Cement & Steel by manual means and stacking

Cost of Haulage excluding loading & unloading a) Cement from Pasighat to Boleng (Lead - 92 Km) (Hill Road) Qnty as per TC

Carriage of river bed materials from quarry to site of work

(SSH:Maintenance of Ty-IV 2Unit)

Demolishing cement concrete 1 : 3 : 6 or richer mix including disposal off material within 50 metres lead.

Dismantling wood work of sectional area below 40 Sq.cm. and above wrought, framed and fixed in frames, other frames and trusses including stacking the material within 50 m lead.

Dismantling doors, windows and clerestory windows (steel or wood) shutters including chowkhats, architrave, hold fasts etc complete and stcking within 50m lead. a) Of area 3 Sq.m. and below

Dismantling GI sheet roofing including ridges, hips, valleys and gutters etc and stacking the material within 50 m lead.

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 m lead.

Repairs to plaster in patches of 2.50 Sq.m. and under including cutting the patch to proper shape and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50 m lead. a) With cement mortar 1 : 4 (1 cement : 4 fine sand)

Providing approved best available local wood (Class - B II) work in frames of doors, windows clerestory windows and other frames, wrought framed and fixed in position.

Providing best available local wood (Class - B II) work in frames of false ceiling, partitions and trusses etc, sawn and put up in position.

Providing and fixing panelled, glazed or panelled and glazed shutters for doors, windows and clerestory windows including aluminium butt hinges with necessary screws. a) 38mm thick best available local wood class - B I

Providing and fixing 12 mm thick insulating board ceiling of approved quality with necessary nails etc. complete (frame work to be paid separately).

Supplying and fixing Glass panes with wooden fillets including removal of broken glass panes and old wooden fillets wherever necessary but excluding cost of wooden fillets. a) Glass panes 3 mm thick and area 0.1 Sq.m. each

Supplying and fixing new wooden fillets wherever necessary. a) 1st class wood fillets

Providing corrugated G.I.sheet roofing fixed with galvanised iron J or L hooks, bolts & nuts 8 mm dia with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead complete, excluding the cost of purlins, rafters and trusses. 0.63 mm thick GI sheet

Construction of cement concrete drain 15 cm wide and 15 cm deep in cement concrete 1 : 3 : 6 (1 cement : 3 sand : 6 hard graded stone chips or shingle 40 mm and down gauge) 8 cm thick on sides and bottom and plastering and all exposed surfaces with 12 mm thick cement mortar 1 : 3 (1 cement : 3 coarse sand) including shuttering complete.

Making plinth protection 50 mm thick of cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 stone aggregate using 20 mm nominal size) over 75 mm bed of stone ballast 40 mm nominal size well rammed and consolidated and grouted with fine sand including finsihing the top smooth.

Providing and fixing Iron T-hinges bright finished or and black enamelled with necessary screws etc complete. a) 300 x 115 x 2.24 mm

Providing and fixing MS door latch with necessary screws etc complete. a) 300 x 20 x 6 mm

Providing and fixing MS handles with necessary screws etc complete. a) 125 mm

Cement concrete flooring 1 : 2 : 4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement. c) 75 mm thick

Distempering (one or more coats) with oil bound washable distemper of approved brand and manufacture and of required shade on old work to give an even shade.

Applying priming coat with ready mixed pink primer of approved brand and manufacture on wood work complete.

Painting two or more coats (excluding priming coat) with superior ready mixed paint for wood work of approved brand and manufacture in all shades on new work to give an even shade.

Painting one or more coats with superior quality ready mixed paint for steel work of approved brand and manufacture in all shades on old work to give an even shade.

Providing and laying cement concrete 1 : 2 : 4 (1 cement : 2 coarse sand : 4 stone aggregate 20 mm nominal size) excluding the cost of centring and shuttering in : Foundations and plinth

Loading and unloading of Cement & Steel by manual means and stacking

Cost of Haulage excluding loading & unloading a) Cement from Pasighat to Boleng (Lead - 92 Km) (Hill Road) Qnty as per TC

b) Steel from Pasighat to Boleng (Lead - 92.00 Km) (Hill Road) Qnty as per TC

Carriage of river bed materials from quarry to site of work

( SSH:- C/o RCC boundary wall )

Earth work in excavation in foundation and trenches in soils containing 50% or more of shingle or small size boulders upto 30 cm size, lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning the stacked soil in 15 cm layers when required, into plinth, sides of foundation etc consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated soil as directed within a lead of 50m.

Re-filling excavated earth in foundations and plinth etc. in 15 cm layer including ramming and watering etc. complete.

Providing and laying in foundations and plinth cement concrete 1 : 4 : 8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering.

Providing and laying cement concrete 1 : 2 : 4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) excluding the cost of centring an shuttering in: b) Walls including attached buttresses, pilasters and their caps and bases and string courses etc. up to floor two level.

Reinforced concrete work in foundations, footings, bases of columns etc. and mass concrete excluding cost of centring, shuttering and reinforcement in : a) M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforcement cement concrete work in columns, pillars, piers, abutments, post and struts etc up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but exluding cost of centring, shuttering and reinforcement. a) M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete work in lintels, beams and bresumers up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centering, shuttering and reinforcement. a) M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Centring and shuttering including strutting, propping etc and removal of form work for : a) Foundation, footings, bases of columns etc. and mass concrete.

b) Walls including attached buttresses, pilasters and their caps and bases and string courses etc. up to floor two level.

c) Column, pillars, posts and struts etc.

d) Lintels, beams, girders, bressumers and cantilevers etc.

Reinforcement of RCC work including bending, binding and placing in position complete. b) Tar/TMT steel.

Masonry with pre-cast cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) blocks in cement mortar 1 : 4 (1 cement : 4 fine sand)for pre-cast cement block masonary in Superstructure.

15 mm cement plaster 1 : 4 (1 cement : 4 fine sand).

Applying one coat of cement primer of approved brand and manufacture on wall surface.

Supply of M.S. Steel Gate of size 1.83x 4.0 mtr .

Supply of M.S. Cattle Trap of size 1.83 x 4.5 mtr.

Loading and unloading of Cement & Steel by manual means and stacking

Cost of Haulage excluding loading & unloading a) Cement from Pasighat to Boleng (Lead - 95 Km) (Hill Road) Qnty as per TC

b) Steel from Pasighat to Boleng (Lead - 92.00 Km) (Hill Road) Qnty as per TC

Carriage of river bed materials from quarry to site of work

Shri Talung Tatak