Junction Improvements works on Junagadh Khadiya Mendarda Road Ch.11/800 K.M. Dist.Junagadh

Name of Work :Junction Improvement works on Junagadh Khadiya Mendarada Road Ch. 11+800 km. Dist.

BILL OF QUANTITY

Sr. Description of Item Quantities Unit Tendered Total amount

Sr. Description of Item Quantities Unit Tendered Total amount

No. Estimated Rate according to

but may be estimated

more or less quantites

1 Clearing and grubbing road land including uprooting 1.00 Hec. 28455.09

rank vegetation grass bushes, shrubs, sapling and

trees girth up to 300 mm removal of stumps of trees

cut earlier and disposal of unserviceable materials (C)

By mechanical means in area of light jungle.

2 Dismentaling the existing structure including 66.00 Cum. 409.22

removing and stacking the dismentelled materials as

and where directed. (B) Rubble Masonry

3 Providing and filling in foundation with ordinary 95.00 Cum. 3345.58

Cement concrete M-100 mix and providing necessary

vertical pin headers including formwork, vibrating,

ramming and curing complete.

4 Providing and fixing pre-cast Rubber Dye / steel Dye 736.00 Sqmt. 706.93

inter locking concrete block 60mm thick with grade of

concrete M300 pnumatic compressed / vibrated

mechanically and as per approved design Confirming

to IS 15658 : 2006 including 35 mm Sand layer for

levelling and filling the joint with sand in proper line

and level as per guidlines of IRC : SP 63-2018 etc.

5 Providing and fixing pre-cast concrete kerb stone of 280.00 Rmt. 402.55

gray cement based concrete block 30cm length,30cm

height and 15cm thick of M200 grade concret as per

approved design and including excavation for fixing in

proper line and level,filling the joint with C:M 1:3

(1cement:3fine sand) etc complete.

6 Finishing wall with weather proof exterior emulsion 126.00 Sqmt. 120.26

paint on wall surface (two coats) to give an required

shape even shade after thoroughly brushing the

surface to remove all dirt, and remains of loose

powdered materials.etc complete.

Name of Work :Junction Improvement works on Junagadh Khadiya Mendarada Road Ch. 11+800 km. Dist.

BILL OF QUANTITY

Sr. Description of Item Quantities Unit Tendered Total amount

Sr. Description of Item Quantities Unit Tendered Total amount

No. Estimated Rate according to

but may be estimated

more or less quantites

7 Hazard Marker Sign :-Providing and fixing sign boards 6.00 No. 3666.30

made out of 2.0 mm aluminium sheet / 4 mm ACP

(Aluminum composite Panel); size 90x30 cms.

rectangular as per design of IRC-67-2012. Pre treated

with phospheting process & acid etching; coated with

one coat of epoxy primer and two coats of best quality

epoxy paint ;reflectorised with Micro Prismatic Grade

retro refiectivesheeting of Type-11 as per ASTM D-

4956 and latest M.O.S.T.Specifications; 1.8mtr long

stand post of 75 x 75 x 6mm / 65NB Circular MS Pipe

as required and frame fabricated from suitable size

iron angle of 35 x 35 x 3mm; painted with bestquality

epoxy coatings in black and white bends. The details

of symbol foreach board shall be as per theinstruction

of engineer in charge. The fixing at site shall be in

1:2:4 CC blockof size 45 x 45 x 60 Cms. for each

leg.including excavation, curing etc.complete under

the supervision of engineer in charge. A warranty for

10 years for the Retro reflective sheeting from

original manufacturer & a certified copy of 3 year

outdoor exposure test report from third party test lab

for the product offered shall be submitted by

contractor. (A) Class-C Type-11 Retro Reflective

Name of Work :Junction Improvement works on Junagadh Khadiya Mendarada Road Ch. 11+800 km. Dist.

BILL OF QUANTITY

Sr. Description of Item Quantities Unit Tendered Total amount

Sr. Description of Item Quantities Unit Tendered Total amount

No. Estimated Rate according to

but may be estimated

more or less quantites

8 Cautionary Warning Sign :-Providing and fixing sign 17.00 No. 5077.27

boards made out of 2mm aluminium sheet / 4mm ACP

(Aluminum composite Panel); size 90 x 90 x 90 cms.

equilateral triangle as per design of IRC-67-2012. Pre

treated with phospheting process & acid etching;

coated with one coat of epoxy primer and two coats of

best quality epoxy paint ;reflectorised with Micro

Prismatic Grade retro refiectivesheeting of Type-11 as

per ASTM D-4956 and latest M.O.S.T.Specifications;

3.6mtr long stand post of 75 x 75 x 6mm / 65NB

Circular MS Pipe as required and frame fabricated

from suitable size iron angle of 35 x 35 x 3mm;

painted with bestquality epoxy coatings in black and

white bends. The details of symbol foreach board shall

be as per theinstruction of engineer in charge. The

fixing at site shall be in 1:2:4 CC blockof size 45 x 45 x

60 Cms. for each leg.including excavation, curing

etc.complete under the supervision of engineer in

charge. A warranty for 10 years for the Retro

reflective sheeting from original manufacturer & a

certified copy of 3 year outdoor exposure test report

from third party test lab for the product offered shall

be submitted by contractor. (A) Class-C Type-11 Retro

Reflective sheeting

Name of Work :Junction Improvement works on Junagadh Khadiya Mendarada Road Ch. 11+800 km. Dist.

BILL OF QUANTITY

Sr. Description of Item Quantities Unit Tendered Total amount

Sr. Description of Item Quantities Unit Tendered Total amount

No. Estimated Rate according to

but may be estimated

more or less quantites

9 Regulatory / Mandatory Sign :-Providing and fixing 9.00 No. 4618.73

sign boards made out of 2mm aluminium sheet / 4mm

ACP (Aluminum composite Panel); size 60 cms Dia

Circle as per design of IRC-67-2012. Pre treated with

phospheting process & acid etching; coated with one

coat of epoxy primer and two coats of best quality

epoxy paint ;reflectorised with Micro Prismatic Grade

retro refiectivesheeting of Type-11 as per ASTM D-

4956 and latest M.O.S.T.Specifications; 3.6mtr long

stand post of 75 x 75 x 6mm / 65NB Circular MS Pipe

as required and frame fabricated from suitable size

iron angle of 35 x 35 x 3mm; painted with bestquality

epoxy coatings in black and white bends. The details

of symbol foreach board shall be as per theinstruction

of engineer in charge. The fixing at site shall be in

1:2:4 CC blockof size 45 x 45 x 60 Cms. for each

leg.including excavation, curing etc.complete under

the supervision of engineer in charge. A warranty for

10 years for the Retro reflective sheeting from

original manufacturer & a certified copy of 3 year

outdoor exposure test report from third party test lab

for the product offered shall be submitted by

contractor. (A) Class-C Type-11 Retro Reflective

Name of Work :Junction Improvement works on Junagadh Khadiya Mendarada Road Ch. 11+800 km. Dist.

BILL OF QUANTITY

Sr. Description of Item Quantities Unit Tendered Total amount

Sr. Description of Item Quantities Unit Tendered Total amount

No. Estimated Rate according to

but may be estimated

more or less quantites

10 STOP Sign :-Providing and fixing sign boards made 1.00 No. 7213.42

outof 2mm aluminium sheet / 4mm ACP (Aluminum

composite Panel); size 90 cms Octagone as per design

of IRC-67-2012. Pre treated with phospheting process

& acid etching; coated with one coat of epoxy primer

and two coats of best quality epoxy paint

;reflectorised with Micro Prismatic Grade retro

refiectivesheeting ofType-11 as per ASTM D-4956 and

latest M.O.S.T.Specifications; 3.6mtr long stand post of

75 x 75 x 6mm / 65NB Circular MS Pipe as required

and frame fabricated from suitable size iron angle of

35 x 35 x 3mm; painted with bestquality epoxy

coatings in black and white bends. The details of

symbol foreach board shallbe as per theinstruction of

engineer in charge. The fixing at site shall be in 1:2:4

CC blockof size 45 x 45 x 60 Cms. for each

leg.including excavation, curing etc.complete under

the supervision of engineer in charge. A warranty for

10 years for the Retro reflective sheeting from

original manufacturer & a certified copy of 3 year

outdoor exposure test report from third party test lab

for the product offered shall be submitted by

contractor. (A) Class-C Type-11 Retro Reflective

Name of Work :Junction Improvement works on Junagadh Khadiya Mendarada Road Ch. 11+800 km. Dist.

BILL OF QUANTITY

Sr. Description of Item Quantities Unit Tendered Total amount

Sr. Description of Item Quantities Unit Tendered Total amount

No. Estimated Rate according to

but may be estimated

more or less quantites

11 Distance Informatory / Destination Sign :-Providing 3.00 Each 20918.11

and fixing sign boards made out of 2mm aluminium

sheet / 4mm ACP (Aluminum composite Panel); size

180x120 cms. rectangular as per design of IRC-67-

2012. Pre treated with phospheting process & acid

etching; coated with one coat of epoxy primer and two

coats of best quality epoxy paint ;reflectorised with

Micro Prismatic Grade retro refiectivesheeting of Type-

11 as per ASTM D-4956 and latest

M.O.S.T.Specifications; 4.0mtr long (2 Nos.) stand post

of 75 x 75 x 6mm / 65NB Circular MS Pipe as required

and frame fabricated from suitable size iron angle of

50 x 50 x 5mm; painted with bestquality epoxy

coatings in black and white bends. The details of

symbol foreach board shall be as per theinstruction of

engineer in charge. The fixing at site shall be in 1:2:4

CC blockof size 45 x 45 x 60 Cms. for each

leg.including excavation, curing etc.complete under

the supervision of engineer in charge. A warranty for

10 years for the Retro reflective sheeting from

original manufacturer & a certified copy of 3 year

outdoor exposure test report from third party test lab

for the product offered shall be submitted by

contractor. (A) Class-C Type-11 Retro Reflective

Name of Work :Junction Improvement works on Junagadh Khadiya Mendarada Road Ch. 11+800 km. Dist.

BILL OF QUANTITY

Sr. Description of Item Quantities Unit Tendered Total amount

Sr. Description of Item Quantities Unit Tendered Total amount

No. Estimated Rate according to

but may be estimated

more or less quantites

12 Village Name Sign :-Providing and fixing sign boards 3.00 No. 6313.51

made out of 2mm aluminium sheet / 4mm ACP

(Aluminum composite Panel); size 90x60 cms.

rectangular as per design of IRC-67-2012. Pre treated

with phospheting process & acid etching; coated with

one coat of epoxy primer and two coats of best quality

epoxy paint ;reflectorised with Micro Prismatic Grade

retro refiectivesheeting of Type-11 as per ASTM D-

4956 and latest M.O.S.T.Specifications; 3.3mtr long

stand post of 75 x 75 x 6mm / 65NB Circular MS Pipe

as required and frame fabricated from suitable size

iron angle of 35 x 35 x 3mm; painted with bestquality

epoxy coatings in black and white bends. The details

of symbol or inscription/letters / numerals for each

board shall be as per the instruction of engineer in

charge. The fixing at site shall be in 1:2:4 CC blockof

size 45 x 45 x 60 Cms. for each leg.including

excavation, curing etc.complete under the supervision

of engineer in charge. A warranty for 10 years for the

Retro reflective sheeting from original manufacturer

& a certified copy of 3 year outdoor exposure test

report from third party test lab for the product offered

shall be submitted by contractor. (A) Class-C Type-11

Retro Reflective sheeting

13 Road marking with hot applied thermoplastic paints 1139.00 Sqmt. 367.72

with reflectorising glass beads on bitumin surface

providing and laying a hot applied thermoplastic

compound 2.5 mm thick including reflectorising glass

beads @ 250gms per sqm area, thickness of 2.5mm is

excluding of surface applied glass beds as per IRC:35-

2015. The finished surface to be level, uniform and

free from streaks and holes. zebra patta /bump patta

lane/center line/ edge line/cut patta. The white color

marking should provide liminance coefficinet on

cemend road shalll be min 130 mcd/m2/lux and

Asphalt road shall be min 100 mcd/m2/lux during the

service life during the day time. The marking should

meet the performance criteria for night time

reflectivity, wet reflectivity and skid resistance as

mentioned in the section-15 of IRC 35-2015.

Warranty for the Retro reflectivity should be two

Name of Work :Junction Improvement works on Junagadh Khadiya Mendarada Road Ch. 11+800 km. Dist.

BILL OF QUANTITY

Sr. Description of Item Quantities Unit Tendered Total amount

Sr. Description of Item Quantities Unit Tendered Total amount

No. Estimated Rate according to

but may be estimated

more or less quantites

14 Cat Eye / Road Stud / RPM: Supplying of Molded 1909.00 No. 326.23

Twin Shanks Raised Pavement Markers made of

polycarbonate and ABS moulded body and reflective

panels with micro prismatic lens capable of providing

total internal reflection of the light entering the lens

face and shall support a load of 13635 kgs. tested in

accordance to ASTM D 4280 Type H and complying to

Specifications of Category A of MORTH Circular No

RW/NH/33023/10-97 DO III Dt 11.06. 1997. The

height, width and length shall not exceed 20 mm,

mm and 130 mm and with minimum reflective area of

13 Sqcm on each side and the slope to the base shall

be 35 +/- 5 degree. The strength of detachment of the

integrated cylindrical shanks, (of diameter not less

than 19 +/- 2 mm and height not less than 30+/-

mm) from the body is to be a minimum value of

Kgf. Fixing will be by drilling holes on the road for the

shanks to go inside, without nails and using epoxy

resin based adhesive as per manufacturers

recommendation and The color of the marker should

be as per the IRC 35-2015 and as directed by Engineer-

Name of Work :Junction Improvement works on Junagadh Khadiya Mendarada Road Ch. 11+800 km. Dist.

BILL OF QUANTITY

Sr. Description of Item Quantities Unit Tendered Total amount

Sr. Description of Item Quantities Unit Tendered Total amount

No. Estimated Rate according to

but may be estimated

more or less quantites

15 Sign board per Squate Meter :-Providing and fixing 4.00 No. 12310.89

sign boards made out of 2mm aluminium sheet / 4mm

ACP (Aluminum composite Panel); size 1meter x1

meter as per design of IRC-67-2012. Pre treated with

phospheting process & acid etching; coated with one

coat of epoxy primer and two coats of best quality

epoxy paint ;reflectorised with Micro Prismatic Grade

retro refiectivesheeting of Type-11 as per ASTM D-

4956 and latest M.O.S.T.Specifications; 4 mtr long

stand post (2 Nos.) of 75 x 75 x 6mm / 65NB Circular

MS Pipe as required and frame fabricated from

suitable size iron angle of 50 x 50 x 5mm; painted

with bestquality epoxy coatings in black and white

bends. the details of symbol or inscription /

numerals for each board shall be as per the

instruction of engineer in charge.The fixing at site

shall be in 1:2:4 CC blockof size 45 x 45 x 60 Cms. for

each leg.including excavation, curing etc.complete

under the supervision of engineer in charge. A

warranty for 10 years for the Retro reflective sheeting

from original manufacturer & a certified copy of

year outdoor exposure test report from third party

test lab for the product offered shall be submitted by

contractor. (A) Class-C Type-11 Retro Reflective

Name of Work :Junction Improvement works on Junagadh Khadiya Mendarada Road Ch. 11+800 km. Dist.

BILL OF QUANTITY

Sr. Description of Item Quantities Unit Tendered Total amount

Sr. Description of Item Quantities Unit Tendered Total amount

No. Estimated Rate according to

but may be estimated

more or less quantites

16 Solar Stud: Supplying of Solar Raised Pavement 90.00 No. 2088.68

Markers made of polycarbonate molded body with

circular shape, solar powered, LED self illumination in

active mode, 360 degree illumination and reflective

panels with micro prismatic lens capable of providing

total internal reflection of the light entering the lens

face in passive mode. The marker shall support a load

of 20000 kg tested in accordance to ASTM D

The marker should be resistant to dust and water

ingress according to IP 65 standards and should

withstand temperatures in the range of 0 C to 70 C.

Color of lighting could be provided in red or yellow

(amber) as per requirement and typical frequency of

blinking is 1 Hz. There should be current losses of less

than 20 micro-amperes at 2.4 V in sleep-charging

mode to enhance the life of the marker and a full

charge should provide for a minimum autonomy of

hours. The height, width and length of the marker

shall not be less than 10 mm x 100 mm x 100 mm.

Also, the surface diameter of the marker shall not be

less than 100 mm respectively. The weight of the

marker shall not exceed 0.5 Kilograms. Fixing will be

by drilling holes on the road for the shanks to go

inside, without nails and using epoxy resin based

adhesive as per manufacturers recommendation and

complete as directed by the engineer

17 Supplying and fixing of prefabricated flexible rubber 100.00 Rmt. 1515.00

speed breaker of size 500 mm x 350 mm x 50 mm,

made out of recycled rubber material with

interlocking male & female ends, including reflective

cat-eye / glass beads / thermoplastic paint strips for

night visibility, with bolts, nuts, washers, and all

necessary accessories. The speed breaker shall be

fixed firmly on the existing road surface using epoxy

adhesive and suitable anchor fasteners, including cost

of all materials, labour, tools, equipment, and

incidentals required for proper completion of the

work as per approved drawings and instructions of

Engineer-in-Charge.

Name of Work :Junction Improvement works on Junagadh Khadiya Mendarada Road Ch. 11+800 km. Dist.

BILL OF QUANTITY

Sr. Description of Item Quantities Unit Tendered Total amount

Sr. Description of Item Quantities Unit Tendered Total amount

No. Estimated Rate according to

but may be estimated

more or less quantites

18 Providing and fixing Flexible Spring Post (Delineator) 50.00 No. 404.00

made of high-impact, UV-stabilized

polyurethane/HDPE with minimum height 750 mm

above road level, fitted with approved retro-reflective

sheeting, capable of self-recovery after impact,

conforming to latest codal provisions. The post shall

be fixed on pavement/shoulder using anchor bolts or

chemical fasteners including drilling holes, grouting,

base plate, nuts, bolts, labour, tools, traffic safety

measures and all incidental works, complete as

directed by the Engineer-in-Charge.

19 Providing, supplying, erecting and commissioning 6.00 No. 18665.81

Solar Blinker mounted on 4.0 m high steel circular

hollow pole for diversion locations, conforming to

IRC:67, IRC:SP:55 and relevant MoRTH Specifications,

consisting of high-intensity amber LED flasher with

constant luminous output and flashing frequency of

40–50 flashes per minute minimum, complete with

suitable capacity solar panel, maintenance-free

rechargeable battery, charge controller, weatherproof

(minimum IP-65) housing, pole with base plate,

necessary wiring, clamps and accessories, including

excavation and construction of suitable RCC

foundation with PCC bed, anchor bolts, grouting,

backfilling, curing and disposal of surplus material,

complete in all respects as directed by the Engineer-in-

Name of Work :Junction Improvement works on Junagadh Khadiya Mendarada Road Ch. 11+800 km. Dist.

BILL OF QUANTITY

Sr. Description of Item Quantities Unit Tendered Total amount

Sr. Description of Item Quantities Unit Tendered Total amount

No. Estimated Rate according to

but may be estimated

more or less quantites

20 Flexible Median Marker : Providing and Fixing of 300.00 No. 271.69

Flexible Median Marker that are made of tough, high

impact resistant, injection-molded, thermoplastic

body with property of flexibility to provide high

durability. The dimension of Flexible Median Marker

should not exceed 18.4 cm in height(including shank

height),12.5 Cm in width. ,0.65 cm in thickness and

shank depth shall be 3.4 cm The body structure shall

be rounded at all its corners and edges. The plastic

used for molding the Flexible Median Marker should

survive impact load of 5kg continuously for 750 times

at room temperature. The logo of the manufacturer

shall be embossed on either side of the body in the

injection molding process. The Median Marker shall

have flame like shaped body with, fluorescent yellow

color retro-reflective sheeting of size not less than

Cm square, with fully reflective micro prismatic cube

corners as its retro-reflective elements as per IRC

2012 and ASTM D4956-09 type XI specifications

reflectivity values. The retro-reflective sheeting shall

be one or both sides of the Flexible Median Marker

and shall be edge protected with no exposed edges

which will prevent edge lifting, vandalism, sheeting

damage, etc. The Flexible Median Marker shall be

fixed by a combination of epoxy adhesive and

grouting as recommended by manufacturer and

Engineer in charge.

Total Twenty nine lakh four thousand two hundred seventy two Only

I/We am/are willing to carry out the work at ……………………………………… % above / below percent [should be written in

figures and words] of the estimated rates mentioned above. Above of my / our tender works out as under.

Estimated Amount Estimated Amount

Put to tender Rs. ……………………………….. Put to tender

Deduct ….……. % below Rs. ……………………………….. Deduct ………..…. % Above

[Please strike out whichever is not applicable]

Name of Work :Junction Improvement works on Junagadh Khadiya Mendarada Road Ch. 11+800 km. Dist.

BILL OF QUANTITY

Sr. Description of Item Quantities Unit Tendered Total amount

Sr. Description of Item Quantities Unit Tendered Total amount

No. Estimated Rate according to

but may be estimated

more or less quantites

[1] The Contractor shall exhibit a board with detailed specification and details of work as directed by the Engineer-

In-Charge for which no extra payment shall be made.

[2] The labour cess will be deducted as per prevailing rules i.e. 1% of the work done.

[3] GST and Income tax TDS will be deducted at a source while making payments of bills

[4] In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per Govt. G.R.: PRC-

10/2017 Cement Consumption/16/C Date:11/05/2017 as stated in S.O.R. therefore in R.C.C. items where

there is a change as per actual mix design the cost of difference of cement consumption have been deducted from

the rate of original item at the rate of input rate mentioned in all the tender.

Signature of Bidder

Deputy Executive Engineer

R&B Sub Division