Different developments works in newly constructed 14 plus 1 Nos Government Quarter Complex at Bhallukya Tilla Agartala under the jurisdiction of Capital Complex Subdivision No II under Capital complex Division building during the year 2025 26.

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth upto 30 cm measured at a height of 1 m above ground level and removal of rubbish upto a distance of 50 m outside the periphery of the area cleared.

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. -All kinds of soil

Construction of Embankment with Material Obtained from Borrow Pits Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with a lead upto 1000 m as per MoRD Technical Specification Clause 301.5.

Supplying and filling in plinth, under floor, foundations etc. with sand (fine) from local quarry with all lifts including spreading in horizontal layers, watering, grading to required slope, ramming, consolidating and compacting each layer by using plate compactor or by any suitable method complete.

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - -All work upto plinth level: 4.1.7 1:4:8 ( 1 Cement: 4 fine sand : 8 graded stone aggregate 40 mm nominal size)

(i) 1:2:4 (Cement: 2 fine sand : 4 graded well burnt brick aggregate 20 mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering, finishing and reinforcement- -All work upto plinth level: (i) 1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size)

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. (i)Thermo-Mechanically Treated bars of grade Fe-500D or more.

First class brick work in foundation and plinth including cost of all materials as required complete:- (i) In cement mortar 1:4 ( 1 cement : 4 fine sand ).

Half brick masonry work with first class bricks in superstructure upto floor five level including cost of all materials as required complete :- (i) In cement mortar 1:4 ( 1 cement : 4 fine sand ).

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position: (i) Karai wood

Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. (i) 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.

Providing and fixing bright finished brass butt hinges with necessary screws etc.complete : (i) 125 x 85 x 5.5 mm (heavy type)

Providing and fixing bright finished brass towerbolts (barrel type)with necessary screws etc. complete : (i) 250 x 10 mm.

(ii) 100x10 mm.

Providing and fixing bright finished brass handles with screws etc. complete : (i) 125 mm.

Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete.

Providing and fixing IS : 3564 marked aluminium extruded section body tubular type universal hydraulic door closer with double speed adjustment with necessary accessories and screws etc. complete.

Providing and fixing chromium plated brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles with necessary screws etc. complete (best make of approved quality).

Providing and fixing ISI marked aluminium butt hinges anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete: (i) 125x75x4 mm

Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete : (i) 300x16 mm.

Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete : (i) 300x10 mm

Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : (i) 125 mm

Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc. complete. (i) Twin rubber stopper

Providing and fixing factory made door frame (single rebate) made of solid PVC foam profile with homogenous fine cellular structure having smooth outer integral skin having 60mm width & 30mm thickness and shall be fixed to wall as per instructions of Engineer-In-Charge using 100x8 sheet metal CSK screws.

Providing and fixing 28 mm thick door shutter made of solid PVC foam profile with homogenous fine cellular structure having smooth outer integral skin having 71mm width & 28mm thick as vertical & horizontal styles. Joints are made using solvent adhesive and GI ‘C sections (39mm x 19mm x 0.6mm thick) or M S pipe (40mm x 20mm ) stiffener frame insert & telescopic polymeric ‘L’ corners .The panel shall be filled with 3mm thick high - pressure compact laminate as per manufacturer’ specifications and directions of the Engineer-incharge, cover moulding shall be provided for covering fixing screws and elegant look.( for W.C. bathroom door shutter).

Providing and fixing Precast chequered cement concrete tiles 18 mm thick, laid in footpath & courtyard, on 20 mm thick bed of cement mortar 1 : 4 ( 1 cement : 4 fine sand ) jointed with neat cement slurry including rubbing and cleaning etc. all complete as per direction of Engineer-in-charge. 1. In dark shade using ordinary cement.

Providing and fixing 1st class quality ceramic glazed wall tiles conforming to IS : 15622 - 2017 (thickness to be specified by the manufacturer) of approved make in all colours, shades of any size as approved by Engineer-in charge in skirting, risers of steps and dados, laid over 12 mm thick bed of cement mortar 1 : 3 (1 cement : 3 fine sand) jointed with ordinary cement slurry including pointing with white cement mixed with pigment of matching shade etc. all complete as per direction of the Engineer in-charge. (i) 450 mm X 300 mm in all shades and design.

Providing and laying ceramic floor tiles in different sizes (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 - 2017 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid over 20 mm thick cement mortar 1:4 (1 cement : 4 fine sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc. complete. (i) Mat Finish Tiles.Anti skid tiles/Glossy tiles (a)Ceramic Tiles 1st quality 300 x 300mm in all shades and designs

Providing and laying 1st class quality vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622 - 2017, of approved make, in all colours and shades, laid over 20mm thick cement mortar 1:4 (1 cement : 4 fine sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc. all complete as per direction of the Engineer-in-charge. 10.42.3 Glazed Vitrified Tiles (Glossy / Mat Finish/ Anti-Skid) (i) Size of tile 600 mm x 600 mm

(ii) Size of tile 1200 mm x 600 mm

Providing and fixing insulating board ceiling of approved quality with necessary nails etc. complete (frame work to be paid separately): (i) 12 mm thick White face insulating board

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high

having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered andsquare edges of the board with recommended jointing compound of joint and two coats of primer su,i tjoabinletinfogr tbapoaersd ,, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : (i) 12.5 mm thick tapered edge gypsum board conforming to IS: 2095- Part I.

12 mm cement plaster of mix. (i) Cement mortar 1:4 (1 cement : 4 fine sand).

Neat cement punning.

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade [Payment shall be made after submission of Test Certificate issued by the Manufacturer] : (i) Two or more coats on new work

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete

Wall painting with acrylic exterior paint (one or more coats ) of required colour of approved brand and manufacture on old work to give an even shade including preparation of surface as required complete as per direction of the Engineer in charge.

Painting with synthetic enamel paint ( one or more coats ) of required colour of approved brand and manufacture on old work to give an even shade including preparation of surface as required complete as per direction of the Engineer in charge.

Varnishing with varnish ( one or more coats of glue sizing ) of approved brand and manufacture on old work including preparation of surface as required complete as per direction of the Engineer in charge:- (i) With copal varnish.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixing with dash fasteners of required dia and size, including necessary filling up of gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawing and the direction of Engineer in charge. (Glazing and paneling and dash fasteners to be paid for separately) :-

(1) For fixed portion of approved quality:- (i) Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15).

For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing fittings wherever required including the cost of EPDM rubber / neoprene gasket required ( Fittings shall be paid for separately ):- (i) Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15).

Providing and fixing 12 mm thick prelaminated three layer medium density (exterior grade ) particle board grade-I, type II conforming to IS : 12823 bonded with phenol formaldehyde synthetic resin, of approved brand and manufacture in panelling fixed in aluminium doors, windows, shutters and partition frames with C.P. brass / stainless steel screws all complete as per architectural drawing and the direction of Engineer-in-charge :- 1. Prelaminated particle board of approved quality with decorative lamination on one side and balancing lamination on other side.

Providing and fixing glazing of approved quality in aluminium doors, windows, ventilator, shutters and partition etc. with EPDM rubber / neoprene gasket etc. complete as per architectural drawing and the direction of Engineer-in-charge (Cost of snap beading shall be paid in basic item) :- (i) With float glass panes of 4.0 mm thickness ( weight not less than 10.0 kg / sqm ).

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embrossed on the body / plate with double spring mechanism and door weight upto 125 kg. for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece MS sheet outer box with slide plate etc. complete as per direction of the Engineer-in-charge:- (i) With stainless steel cover plate minimum 1.25 mm thickness.

Providing and fixing stainless steel ( SS 304 grade ) adjustable friction window stay of approved quality with necessary stainless steel screws etc. to the side hung windows etc. complete as per direction of Engineer-incharge:- (i) 205 x 19 mm.

(ii) 255 x 19 mm.

Providing and fixing aluminium round shape handle of outer dia 100 mm with SS screws etc. of approved quality complete as per direction of Engineer-in-charge:- (i) Anodised aluminium of grade AC 15 ).

Providing and fixing aluminium tubular handle bar of 32 mm outer dia, 3.0 mm thick and 2100 mm long with Stainless Steel screws etc. of approved quality complete as per direction of Engineer-in-charge:- (i) Anodised aluminium of grade AC 15 ).

Providing and fixing 100 mm brass locks (best make of approved quality) with 6 levers without pair of handles for aluminium doors including necessary cutting and making good etc. complete as per direction of Engineer-in-charge.

Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound, as directed by Engineer-in-Charge and consisting of applying : (a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. (b) laying second layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm. (c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg/sqm and fine sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around. (d) fourth and final layer of brick tiling with cement mortar (which will be paid for separately. For the purpose of measurement the entire treated surface will be measured.

Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litres with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in- Charge.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required : (i) W.C. pan with ISI marked white solid plastic seat and lid.

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the wallswherever require : (i) White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps.

Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubber plug 40mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complete including painting of fittings and brackets, cutting and making good the wall wherever required : (i) Size 450x300x150mm.

Providing and fixing white vitreous china water closet squatting pan (Indian type) (i) Long pattern W.C. pan of size 580 mm .

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : (i) Rectangular shape 453x357mm.

(ii) Rectangular shape 1500x450 mm.

Providing and fixing 600x120x5mm glass shelf with edges round of supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete.

Providing and fixing toilet paper holder : (i) C.P. brass.

Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete. (i) 10 litre capacity-White.

(ii) 10 litre capacity-coloured.

Providing and fixing controlled flush, low level cistern made of vitreous china with all fittings complete. (i) 10 litre (full flush) capacity-coloured.

Providing and fixing white vitreous china wash basin including making all connections but excluding the cost of fittings: (i) Flat back wash basin of size 550x400mm.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. (1) Semi rigid pipe (i) 32 mm dia.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour. (i) 450mm long towel rail with total length of 495mm, 78mm wide and effective height of 88mm, weighing not less than 170 gms.

Providing and fixing solid plastic seat with lid for pedestal type W.C. pan complete : (i) White solid plastic seat with lid.

Providing and fixing G.I. pipes of medim class as per IS : 1239 with latest amendment complete with G.I. fittings and clamps, including cutting and making good the walls etc. complete as per CPWD specification and direction of the Engineer - in - charge. Internal work - Exposed on wall. (i) 15 mm dia. nominal bore.

(ii) 25 mm dia. nominal bore.

(iii) 40 mm dia. nominal bore

Providing and fixing G.I. pipes of medim class as per IS : 1239 with latest amendment complete with G.I. fittings including trenching and refilling etc. complete as per CPWD specification and direction of the Engineer - in - charge. Externalwork (i) 32 mm dia. nominal bore metre

(ii) 40 mm dia. nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end): (i) 32 mm nominal bore.

(ii) 50 mm nominal bore.

Providing and fixing ball valve (brass) of approved quality High or low pressure, with plastic floats complete : (i) 15 mm nominal bore.

(ii) 25 mm nominal bore.

Providing and fixing uplasticised PVC connection pipe with brass unions : (a) 30 cm length. (i) 15 mm nominal bore.

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet: (i) 150 mm diameter.

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. (i) 15 mm nominal bore.

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. (i) 15 mm nominal bore.

Providing and fixing PTMT pillar cock of approvedquality and colour . (i) 15mm nominal bore, 125mm long foam flow, Weighing not less than 120 gms.

Providing and fixing on wall face unplasticised Rigid PVC rain water, soil, waste & vent pipes (working pressure 4 kg / cm2) conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion: (i) Single socketed pipe - 75 mm OD.

(ii) Single socketed pipe - 110 mm OD .

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water, soil, waste & vent pipes pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion: (a) Coupler (i) 75 mm.

(b) Single equal tee with door (i) 75x75x75 mm.

(ii) 110x110x110mm.

Labhour charge for maintenance of pvc door shutters after dismentelling and fixing the same to its original position as per direction of the Engineer in Charge.

Providing and fitting pvc fly proof net/mosquito net with velco tap and wooden beading (Gamair wood) of size 50 mm x 37 mm screw nails etc. Complete as per direction of the Engineer in charge.

Providing and fixing heavy duty hydraulic door closer (Godrej make) or equivalent with accessories and screws etc. Complete.

Providing and fixing mortise lock (Godrej make) 6 lever product code no. 3939/3938 or equivalent including cost of all accessories and screws etc. Complete .

providing and fixing swan neck piller cock of approved quality (MARC etc.) of ISI standered as per direction of the Engineer in charge. (i) 15 mm nominal bore .

Providing and fixing CP hand sprey with holder and connection PVC fixed to wooden steel wire brass screw. (i) 15 mm nominal bore.

Providing and fixing 15 mm dia. CP angular two and one stop cock of approved quality as per direction of the Engineer in charge.

Providing and fixing of vanishing blind at approved quality and colours (VISTA VERTICAL BLINDS ) Range name “ CHENILLE “ and drop at minimum 1.00 m lowers with 100 mm including installation the same as per direction of the Engineer-in-charge.

Providing and fixing gang saw cut of approved thickness mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base of cement mortar 1:4 ( 1 cement : 4 fine sand ) with joints treated with white cement, mixed with rubbing , curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels: (i) 18 mm thick Rajnagar Plain white marble/ Udaipur green marble/ Zebra black marble or equivalent duly approved: (a) Area of slab upto 0.50 sqm.

(b) 18 mm thick Granite of any colour and shade duly approved: (a) Area of slab upto 0.50 sqm.

Carpeting setting for stage and audience shed, Road etc. as per Engineer – in – charge. On hire charges basis.

Supplying and laying armless chair with cloth cover including loading, unloading and placing the same as per Engineer – in – charge. On hire charges basis.

Providing and fixing glazing of approved quality in aluminium doors, windows, ventilator, shutters and partition etc. with EPDM rubber / neoprene gasket etc. complete as per architectural drawing and the direction of Engineer-in-charge (Cost of snap beading shall be paid in basic item) :- (i) With float glass panes of 8 mm thickness ( weight not less than 20 kg / sqm ).

Providing and fixing curtain rods of 1.25 mm thick chromium plated brass plate, with two chromium plated brass brackets fixed with C.P. brass screws and wooden plugs, etc., wherever necessary complete. (i) 20 mm dia.

Providing & fitting fixing good quality cotton / polyster screen for window screen provision including bracket where necessary complete as per direction of the engineer –in-charge.

Providing & fixing chrome plated brass battery based infrared sensor operated pillar cock, having foam flow technology i. 15 mm nomial bore

Providing and fixing wall panelling / partion wall by 19 mm thick Green Solid plywood of make Greenply/ Century ply or equivalent as per IS 710 : 2010 and and back will have 19 mm thick 50mm x 19mm plywood in both horizontal and vertical direction at 600mm C/C and 1200mm C/C respectively, completed with all necessary hardware and fittings as per approved drawing, design and direction of the Engineer-in-charge.

Providing and fixing 1mm thick laminate (New Mica) of make Greenply / Century ply or equivalent as per IS 710 : 2010 in wall panelling / partition wall etc. completed with all necessary adhesive, paper strip hardware fitting etc. as per approved drawing design and direction of the Engineer-in-charge.

Providing and fixing wall cabinet of size- 2.40m x 1.80m x 0.45m) is made of Greenply( Ecotec-710 grade or eqivalent) as per IS : 710:2010, 19mm solid plywood and back will have 12 mm plywood pasted finished with 1 mm thick laminate a per IS : 710:2010 for outside and inside will be finish in 0.8mm laminate of approved shad completed with all necessary hardware and fittings, such as stainless steel but hinges, Magnetic catcher, brass cup board lock, brass handles etc. complete as per approved drawing and direction of the Engineer-in-charge.(only front side area will be measured)

Providing and fixing wall panelling / partion wall by 12 mm thick Green Solid plywood of make Greenply/ Century ply or equivalent as per IS 710 : 2010 and and back will have 12 mm thick 50mm x 12 mm plywood in both horizontal and vertical direction at 600mm C/C and 1200mm C/C respectively, completed with all necessary hardware and fittings as per approved drawing, design and direction of the Engineer-in-charge.

Providing and fixing overhead wall cabinet of size- 2.70m x 0.60m x 0.45m) is made of Greenply( Ecotec-710 grade or eqivalent) 19mm solid plywood and back will have 12 mm plywood pasted finished with 1 mm thick laminate for outside and inside will be finish in 0.8mm laminate of approved shad completed with all necessary hardware and fittings, such as stainless steel but hinges, Magnetic catcher, brass cup board lock, brass handles etc. complete as per approved drawing and direction of the Engineer-in-charge.(only front side area will be measured)

Supplying and fitting fixing of pillar cock auto closing system of approved quality (ISI marked) (Jaquar make code PRS-CHR-031 or equivalent) weight not less than 850 grams each as per direction of the Engineer in Charge:-i. 15 mm nomial bore.

Supplying and fitting fixing of bib cock auto closing system of approved quality (ISI marked) (Jaquar make code PRS-CHR-043 or equivalent) weight not less than 650 grams each as per direction of the Engineer in Charge:- i. 15 mm nomial bore.

Supplying and fitting fixing of Urinal valve auto closing system of approved quality (ISI marked) (Jaquar make code PRS-077 or equivalent) weight not less than 450 grams each as per direction of the Engineer in Charge:-i. 15 mm nomial bore.

Providing and fixing PTMT 15 mm Urinal spreader size 95x69x100 mm with 1/2" BSP thread and shapes, weighing not less than 60gms.

Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour.

i. Waste coupling 31 mm of 79mm length and 62mm breadth weighing not less than 45 gms.

Providing making and installation of office furniture of different size and shape like File board shelf/Book shelf/Working table with drawer facility/ small table etc using 19 mm thick solid plywood of make Greenply( ECOTEC PLATINUM -710)/Century or equivalent conforming to IS: 710:2010 including making charges, the cost of adhesive,screw, etc and pasting 1mm thick laminate over 19 mm ply wood (cost of 1 mm thick laminate/mica and fittings if required will be paid separately) complete as per direction of Engineer -in -charge. Only 19mm thick ply area will be measured for payment.

60 mm thick factory made c.c interlocking paver block of M -30 Grade Cement concrete 1:2:4 in pavements, laid to required slope and camber in panels Providing and laying 60 mm thick factory made cement concrete interlocking paver block of M-30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50 mm thick compacted bed of sand, filling the joints fine sand etc. all complete as per specification and approval/ direction of the Engineer-in-charge.

Providing supplying and installation of Curtain choth including two side stiching of Fabric code ALDEN17,(Composition of fabric 100 % Polyester,GSM 285,Width 137.5 Cm) complete as per direction of the Engineer-in-charge

Providing supplying and installation of blackout Curtain choth including two side stiching of Fabric code Linear SR No 10 (Composition of fabric 100 % Polyester,GSM 276,Width 140 Cm) complete as per direction of the Engineer-in-charge

Providing supplying and installation of Shear Curtain choth including two side stiching of Fabric code IMAIT 01 No 10 (Composition of fabric 471 % Cotton, 35 & Viscose, 24% Polyester,GSM 137 . Water and stain repellent complete as per direction of the Engineer-in-charge

Providing supplying and installation of M Track (Metalic track) ,easy glide M track with runner for slide the curtain and endcap. Celling and wall holder for fix the M track as per our need. This heavy duty, white powder coated, uv -protected M track have bending feasibility in 90 degree width wide angle as per curves shape complete as per direction of the Engineer-in-charge

Stiching of Plate curtain of length measuring from track to desire drop upto 3.00 meter with adding 10-16 inchs for hems (Top and bottom) and prioviding hooks for hang the curtains on the track (Width of the curtain 135-140 Cm) complete as per direction of the Engineer-in-charge