REPAIR TO JOINERY, PLASTERING, FLOORING, ROOFING, PLINTH PROTECTION, CEILING AND BRICK WORK ETC FOR OMQ SMQ AREA AT AF STATION BAREILLY

Amount

Demolition of un-reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

M&L for plain cement concrete (1:2:4) type B-1 (using 20 mm graded stone aggregates) as in coping, parapets, bed plates, kerb and the like rounded or chamfered on edges complete all as specified and as directed.

Demolition of brick work built in cement mortar or cement lime mortar including all quions, arches, pillars etc complete all as specified and as directed.

M&L for fly ash brick work with old size bricks, straight or curved on plan exc 6.0 mtr mean radius built in cement mortar (1:6) complete all as specified and directed.

S&F in repair 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls with and including MS clamps complete all as specified and directed.

S&F PVC (SWR) bends any radius of bore 110 mm complete all as specified and directed.

Demolition of cement concrete in ground floors and paving n exc 15cm thickness below or above ground level complete all as specified and as directed

M&L for 75 mm thick cement concrete (1:3:6) type C1, (using 20 mm graded stone aggregates) as in plinth protection, laid in bay n exc 3.00 sqm each finished even and smooth without using extra cement with and including all necessary form work to divide the area in panels, finishing exposed edges fair or rounding or chamfering where directed and providing 6 mm wide joints through out the thickness of plinth protection duly filled with mastic filling (one part of hot bitumen 85/25 and three part of fine sand by weight) complete all as specified and directed.

M&L for 75 mm thick cement concrete (1:2:4) type B1, (using 20 mm graded stone aggregates) as in floor, surface finished even and smooth without using extra cement complete all as specified and directed.

Taking down cement plaster including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and as directed.

M&L for 15 mm thick rendering with cement mortar (1:4) mixed with water proofing compound, on fair face of brick work or concrete surfaces, surface finished even and fair complete all as specified and directed. Note:- Water proofing compound shall be measured and paid seperately.

M&L for 15 mm thick rendering in CM (1:4) mixed with liquid WPC on fair faces of brick or concrete surfaces, finished fair and even at wall height from 3.0m to 8.0 mtr including necessary steel scaffolding complete all as specified and directed. Note :- WPC shall be measured and paid separately.

M&L for 15 mm thick rendering in CM (1:6) in patches on fair faces of brick or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

Supply only liquid water proofing compound complete all as specified and diredcted.

M&L for 10 mm thick rendering in CM (1:3) on concrete surfaces as on ceiling complete all as specified and as directed.

M&L for prepration of new plastered surface of wall and applying two coats of cement base paint over one coat of primer complete all as specified and directed.

M&L for prepration of new plastered surfaces of wall and applying two coats of oil bound distemper over a coat of primer complete all as specified and directed.

M&L for prepration of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

Preparation of old surfaces including brooming down to remove all dust, dirt and loose scales and other foreign matter or steel wire brushing, scrapping down smoke soot, greasy spots, moulds, moss and efflorescent salts and trading oil and applying one coat of white wash on ceiling complete all as specified and directed.

Preparation of old surfaces including brooming down to remove all dust, dirt and loose scales and other foreign matter or steel wire brushing, scrapping down smoke soot, greasy spots, moulds, moss and efflorescent salts and trading oil and applying two coats of cement base paint on wall complete all as specified and directed.

Preparation of old surfaces including brooming down to remove all dust, dirt and loose scales and other foreign matter or steel wire brushing, scrapping down smoke soot, greasy spots, moulds, moss and efflorescent salts and trading oil and applying one coat of oil bound distemper on wall complete all as specified and as directed.

Preparation of old surfaces including brooming down to remove all dust, dirt and loose scales and other foreign matter or steel wire brushing, scrapping down smoke soot, greasy spots, moulds, moss and efflorescent salts and trading oil and applying one coat of white wash on wall complete all as specified and as directed.

Taking down chowkhats or frames with shutter (without taking off shutter from the frame) area exc 1.5 but n exc 4 sqm each complete all as specified and as directed.

Taking down chowkhats or frames with shutter (without taking off shutter from the frame) area n exc 1.5 sqm each complete all as specified and as directed.

Taking down shutter from frame of area exc 1.00 Sqm but not exc 2.00 Sqm each complete all as specified and as directed.

Taking down shutter from frame of area n exc 1.00 Sqm each complete all as specified and as directed.

S & F factory made PVC door frame of size 50 x 47mm with a wall thickness of 5mm grid PVC sheet mitered at corner and pinned with two members 150mm long brackets of 15 x 15mm MS Square tube 19 gauge EPDM rubber gasket weathered sheet to be provided through the frame, door frame to be fixed to the wall suing MS screw of 65/100mm size complete as per manufacturer specification

S & F 35mm thick factory made solid panel PVC door shutter conforming as per IS-4020 made from MS tube of 19 Gauge thickness of size 19 x 19mm style and 15 x 15mm for rail covered with heat moulded PVC channel of 5mm thick and 75mm, 125mm, 125mm wide for top rail, lock rail and bottom rail on either side at 5mm thick 20mm wide cross PVC sheet of gap inserted for top rail and bottom rail, paneling of 5mm PVC sheet fitted in MS frame welded/sealed to the style at rail with 30mm wide, 5mm thick PVC sheet beading sides and jointed together with solvent cement adhesive etc including aluminimum mongry complete all as specified and directed by Engineer-in-Charge.

M&L 2nd class hard wood for plain, solid, straight, chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and as directed.

M&L for flush shutters, 35mm thick solid core construction, with block board core and plywood face panels, commercial type on one side and one face is covered with decorative face veneer with lipping/frame to match complete all as specified and as directed.

M&L for 2nd class hard wood glazed and skeleton shutter 35mm thick, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.24 (a); supplied and fitted to chowkats complete all as specified and as directed.

S&F 300mm length aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding door bolts of extruded sections or cast aluminium alloy complete all as specified and as directed.

S&F 250mm length aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding door bolts of extruded sections or cast aluminium alloy complete all as specified and as directed.

S&F 100 mm long stainless steel Butt hinges with stainless steel hinge pin ISI marked complete all as specified and as directed.

S&F 125 mm long extruded aluminium alloy handles, fabricated type, anodized, ISI marked complete all as specified and as directed.

S & F in repair 150 mm long aluminium, anodised, barrel tower bolts of extruded section ISI marked complete all as specified and as directed.

S&F in repair 300 mm mild steel ordinary door springs, ISI marked including roller and roller plate complete all as specified and directed.

M&L for preparation of new wooden surfaces of any description not otherwise described over 10cm wirdh or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and as directed.

M&L for preparation to old steel surfaces of any description over 10cm wirdh or girth and applying two coats of synthetic enamel paint complete all as specified and as directed.

M&L for preparing surface of new wood and wood based materials, steel and iron work, new or old, of any descrition and girth, not otherwise described, and treated with tar or coal tar black paint complete all as specified and as directed.

M&L for preparing surface of new wood and wood based materials, steel and iron work, new or old, treating small articles such as holdfasts etc and treated with tar or coal tar black paint complete all as specified and as directed.

M&L for 15 mm thick rendering with cement mortar (1:4) mixed with water proofing compound, on fair face of brick work or concrete surfaces, surface finished even and fair complete all as specified and directed. Note:- Water proofing compound shall be measured and paid seperately.

S&F in repair for mild steel for Bands, straps, supports or stays for rainwater, ventilating pipes,including bolts, if required: hooks (stay), heavy, for largegates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and as directed.

S&F steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay & MS tower bolts 100mm -4 Nos complete with glazing bars, dovetailed or welded complete all as specified and as directed.

S&F Steel ventilator with top hung shutters including hinges, peg stay with glazing bars, dovetailed or welded complete all as specified complete all as specified and as directed.

M&L mild steel framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or FE 310-0 complete all as specified and as directed.

S&F 150 mm long extruded aluminium alloy handles, fabricated type, anodized, ISI marked complete all as specified and as directed.

S&F 140mm length of floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring fixed in floor complete all as specified and as directed.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainlees steel wire staples complete all as specified and as directed.

S&F in repair stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainlees steel wire staples complete all as specified and as directed.

Supply and fixing 100mm long hinges, aluminium alloy anodised, cast type complete all as specified and as directed.

S&F 3mm thick sheet glass, ordinary quality and glazing with oil putty in square in n exc 0.5 sq.m in each pane complete all as specified and as directed.

S&F 3mm thick sheet glass, ordinary quality and glazing with oil putty in square in exc 0.5 sq.m in each pane complete all as specified and as directed.

S&F 3mm thick figured glass or pin headed type, ordinary quality and glazing with oil putty in square in n exc 0.5 sq.m in each pane complete all as specified and as directed.

Hacking out old broken glass (any thicknesss, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

M&L for roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. complete all as specified and as directed.

M&L for providing 25 mm thick cement concrete (1:2:4) type B-O (using 12.5 mm graded crushed stone aggregate) as in floor etc surface finished even and fair complete all as specified and as directed.

M&L for 15mm thick screed bed or bedding layers of cement mortar (1:6) for laying floor finishes complete all as specified and as directed.

M&L for brushing neat cement slurry with 3.0 kg of cement per sqm complete all as specified and as directed.

M&L for 10 mm thick rendering with cement mortar (1:4) on fair faces of brick work or concrete surfaces, surface finished even and fair complete all as specified and directed.

M&L for non skid coloured ceramic tiles 7-8mm thick (square / rectangular) area of each tile exc 0.11 sqm but n exc 0.18 sqm each, as in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile complete all as specified and as directed.

M&L for vitrified ceramic tiles 10 mm thick (Square/rectangular) polished double charged area of each tile exc 0.18sqm but not exceeding 0.36 sqm, as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cemeent to match the surface of tile complete all as specified and as directed.

M&L for glazed ceramic coloured tiles of size (450mm x 300mm) x 7mm thick as in vertical surfaces etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile complete all as specified and as directed.

M&L in repair 18/19mm thick prelaminatd particle board, interior grade, prelaminated one side with deocrative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and as directed.

S&F 100mm size Hasp and staple, mild steel, wire type, stove enamelled black, including bolt to hinge plate and fixed with screws complete all as specified and as directed.

S&F Contineous (piano) hinges, bright finish or electrogalvanised, mild steel 30 mm width of flaps (when open) complete all as specified and as directed.

S & F in repairs of stainless steel cupboard/cabinet / drawers handle having a length of 250mm and shape complete all as specified and as directed.

S&F brass locks for cupboard, grade 1, size 65 mm complete all as specified and as directed.

M&L for chamfers, splays, grooves, rebates, rounded angles, rounded nosings, tongued and grooved edges (each tongue and each groove measured) etc., exc 3mm but n. exc 75mm girth on softwood complete all as specified and as directed.

M&L for mild steel bars 10mm dia TMT bars and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M&L for mild steel bars 6 to 8mm dia TMT bars and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M&L for use & waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs etc. also splayes between floors and beams in rough finished surface of concrete complete all as specified and directed.

M&L for providing reinforced cement concrete (1:1.5:3) (Nominal Mix) type B-1, (using 20 mm graded stone aggregate) as in in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces and the like complete all as specified and as directed.

Demolition of reinforced cemet concrete of any description roofs, floors (other than ground floors), beams, staircases, landings, chajjas and simillar suspended work, reinforcement cut as required to facilitate demolition complete all as specified and as directed.

M&L for preparation of new steel surfaces of any description not otherwise described over 10cm wirdh or girth and applying two coats of synthetic enamel paint over one coat of zinc chrome primer complete all as specified and as directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc, laid, bedded and pointed in any mortar complete all as specified and as directed.

M&L for Udaipur Green stone work 18 to 20mm thick (table rubbed and polished) AS in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade complete all as specified and as directed.

M&L for machine cut kota stone slab flooring 18-22mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

M&L for Kota stone slab 18-22mm thick as in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

S&F in repair mild steel, plain black sheet 1.25mm thick in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete all as specified and as directed.

S&F mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete Fe 410 -W(Gde E- 250) quality A complete all as specified and as directed.

M&L for welding in repairs n. exc 2.5cm in length, thickness of metal to be welded n. exc 6mm complete all as specified and as directed.

M&L for welding in repairs exc 2.5cm but n exc 5cm in length, thickness of metal to be welded n. exc 6mm complete all as specified and as directed.

M&L for rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and as directed.

Demolition of cement concrete of any description and in any position as in floors/sunken floors complete all as specified and disposing off debries outside MD land complete all as specified and as directed.

M&L for 100mm thick plain cement concrete (1:4:8) type D-2 (using 40mm graded stone aggregate) as in sub base of interlocking tiles complete all as specified and as directed.

M&L for sand filling under paver block/floors or in foundation including wartering and consolidation complete all as specified and as directed.

M&L for 60mm thick Machine pressed precast concrete interlocking paver block with grey cement and pigments, any shape and size conforming to IS 15658-2006, M-35 Grade complete all as specified and as directed.

S & F of aluminium anodised powder coated of approved colour, sliding type three track (02 glazed shutters and 01 gauzed shutter) window with sliding shutter and frame with and including aluminium grill, 5 mm thick tinted glass and mosquito proofing net as detailed below complete all as specified and directed: - (i) Frame section 91.85 X 31.75 X 1.30 mm, section No. 8758 for top and sides rails and 91.85 X 31.75 X 1.20 mm for bottom rail, section No. 8687. (ii) Shutter for top, bottom and side rails 40 X 18 X 1.50 mm, section No. 8820. (iii) Glass 5.00 mm thick one side reflective glass and other side visible fixed with rubber gasket and aluminium clips bearing section No. 4407 and necessary handles, tower bolt etc. as directed. (v) Stainless steel wire cloth fix with aluminium fame (vi) Filling of gap between wall and aluminium frame with silicon putty to make it proper water tight. (vii) Locking arrangement and providing Namda rope to make the frames air tight.

S&F powder coated aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified and as directed.

S&F powder coated aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified and as directed.

S&F powder coated aluminium (minimum thickness of powder coating 50 microns) work for doors, windows, ventilators and partitions (fixed portion) complete all as specified and as directed.

S&F anodised aluminum grill (anodised transparent or dyed to reqd shade according to IS:1868 with minimum anodic coating of grade AC15) of approved design /pattern, with approved standard section and fixed to the existing window frame with CP brass /stainless steel screw @200 mm center to center including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the openning all complete as per requirement and direction of Engineer-in-Charge.

S &F for 5.50 mm thick sheet glass (tinted/reflective type) in square each pane complete all as specified and as directed.

S&F 12mm thick prelaminated boards, interior grade, prelaminated both sides with decorative choice laminations veneer on both faces fixed complete all as specified and as directed.

S&F in repair Mortice lock, brass, 2 levers, vertical type, size 65 mm complete all as specified and as directed.

M&L for PCC (1:3:6) type C-2 (using 40mm graded stone aggregates) as in foundations, filling and mass-concrete complete all as specified and as directed.

S&F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S 1161-1979 grade St.-240 complete all as specified and as directed.

S&F GDE Fe 410-W Plates (plain or chequered) channels, Square cut or notched (ordinary and counter sunk) forming holes, without any attachment complete all as specified and as directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc. complete all as specified and as directed.

Dismantling of sbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified and as directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.5mm thick of any colour having tensile strength of 550 Mpa as in trangular roof covering/cladding to wall,fixed with self tapping screws complete all as specified and as directed.

M&L for glass dividing strips, 3mm thick width of strip 38mm, inserted in position, conform to design complete all as specified and as directed.

S&F in repair floor door stopper 150mm aluminium alloy body and tongue, anodised with hard drawn steel spring complete all as specified and as directed.

S&F in repair 25 mm dia CP curtain rod with and including supply and fixing brackets, stops, rollers ets complete all as specified and as directed.

S.K.Enterprises

M/s M Aali construction co

Ikrar khan & co.