CA NO. CWE KOTA / ALW-53 OF 2019-20 SPECIAL REPAIR TO BLDGS IN JCOs MD ACCN AT ITARANA CANTT ALWAR

Amount

B/R ITEMS Demolition of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars & precast concrete mosonry etc. and removal all rubbish material complete all as specified directed.

Demolition of cement concrete (reinforced) as in roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors and pavings not exceeding 15 cm thickness below or above ground level and removal all rubbish material complete all as specified and directed.

Removing steel window shutters by cutting hinges by welding and making good any damage occurred during removal of shutters not exceeding 0.75 sqm each, complete all as specified and directed.

Taking down cement or cement lime plaster any description, on brick or stone walls, etc. including racking out joints, hacking for key & scrubbing down with water, etc. & removing rubbish off the premises, complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the primises, complete all as specified and directed.

Dismantling of stone slab and tiles of any description or thickness in floors, aprons etc, laid, beded and pointed in any mortar including removing the dismantled material, complete all as specified and directed.

Dismantling of 75mm/ 110mm dia AC pipe/ PVC pipes, complete all as specified and directed.

Taking down carefully existing bitumen tarfelt, including plaster of any description over the surfaces of roof, terraces including flashings and juctions of parapets/ curb walls etc and removing of the rubbish to a distance exc. 500m but n. exc 1.00 km and depositing where directed, complete all as specified and directed.

Taking down chowkats or frames not exceeding 1.5 Sqm each with shutter (without taking off shutter from the frame) complete all as specified and directed.

Taking down chowkats or frames exceeding 1.5 Sqm but n.exc 4 Sqm each with shutter (without taking off shutter from the frame) complete all as specified and directed.

Taking down shutters of any description exc. 1.00 sqm & n exc. 2.00 sqm each and removing from site complete all as specified and directed.

Taking up or down steel tubing and connections alongwith bib tap, stop cocks and other fittings including cleaning for refixing or removal complete all as specified and directed :-

15mm bore.

20mm bore.

Disconnecting existing tanks, of capacity exceeding 250 Ltrs but not exceeding 500 Ltrs setting aside (or lowering if required) for repairs, cleaning etc. and housing if required reconnecting and refixing in position complete all as specified and directed .

Dismantling water tank of capacity exceeding 250 Ltrs but not exceeding 500 Ltrs and removal from site to stores complete all as specified and directed .

Supply only liquid water proofing Admixture ISI mark complete all as specified and directed.

M & L for brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and directed.

M & L for brick work with sub class- B bricks, straight or curved on plan to any radius in half brick thick walls, built in CM in 1:4 complete all as specified and directed.

S & F Factory made solid PVC moulded door shutter, 28 to 30 mm thick (style), with 2, 4 or 6 raised panel design with 2mm thick moulded prelaminated PVC sheet on the front face & 2mm thick plain colour PVC sheet on back face, supplying and fixing in frame at site as all as per specifications and drawings as applicable to item 08101 given in SSR Part – II.

S & F 35mm thick factory made glazed and skeleton door shutters open rebated of second class hard wood rail and styles(Hollock), prepared to receive glass/gauge etc without sash bars, edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass/gauge etc . The size of rails & style as specified in SSR Part-I (2009) section 8 and as per IS-1003(Part-I) kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and directed. (Note :- S & F Glass/gauge shall be measured and paid for separately)

S & F 35mm thick factory made IInd Class Hard wood (Hollock) plain framed, panelled door shutters two panel with lock rail and panel of 9mm B.W.P. marine grade plywood bonded with high quality liquid phenol formaldehyde synthetic resin adhesive conforming to IS-710 or 12mm thick particle board veneered with commercial veneering on both faces. The size of rails & style as specified in SSR Part-I (2009) section 8 and as per IS-1003(Part-I) kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and directed.

S & F for Solid PVC Door Frame of size 50mm x 47mm made out of 10mm single side prelam PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing as applicable to item 08095 given in SSR Part – II (2010) complete all as specified and directed.

S & F 100 mm size butt hinges, medium weight, stainless steel, ISI marked complete all as specified and directed.

S & F 100 mm size butt hinges, cold rolled mild steel, medium weight, ISI marked complete all as specified and directed.

S & F 75 mm size butt hinges, cold rolled mild steel, medium weight, ISI marked complete all as specified and directed.

S&F 250mm long mild steel sliding door bolts, plate type, stove enamelled black with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, 04 on bolt plate and 02 on staple plate and fix complete all as specified and directed by Engineer-in-Charge.

S & F 150mm long aluminium anodised barrel tower bolt of extruded section and fixed, complete all as specified and directed.

S & F 200mm long aluminium anodised barrel tower bolt of extruded section and fixed, complete all as specified and directed.

S & F 125mm size extruded aluminium alloy handles, fabricated type, anodised, ISI marked complete all as specified and directed.

S & F 150mm size extruded aluminium alloy handles, fabricated type, anodised, ISI marked complete all as specified and directed.

S & F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanised wire staples complete all as directed.

S & F 4mm thick sheet glass frosted and glazing with rubber bedding in squares not exc. 0.5 Sqm in each pane complete all specified and as directed.

Supply fabrication and fixing powder coated (Thickness of powder coating not less than 50 micron) aluminium windows and ventilator shutters, side hung type without sash bars, aluminium section weighing 0.55 Kg/RM including necessary jointing cleats, glazing clips, rubber neoprene packing, powder coated anodised aluminium snap beading, screws, powder coated anodised aluminium fittings such as peg stays 150mm long (01 No. for each leaf), Butt hinges type B-21 100mm size (02 Nos for each leaf) & handle (01 No for each leaf) etc complete all as specified and directed. Make:- JINDAL/HINDALCO (Note :- Glazing/wire mesh shall be measured and paid separately under respective items of Schedule).

S&F for framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete conforming to Fe.290.Gde-E-165 complete all as specified and directed.

S & F for mild steel cupboard shutter with frame, Godrej Pattern, made out of 22 guage mild steel sheet including chromium plated MS handle with proper locking arrangment (brass mortice lock, vertical type, size 65mm, 4 Lever with escutcheon plates & two keys) with & including two coats of spray painting with synthetic enamel paint of approved tint over a coat of red oxide primer including fixing with 06 Nos 12mm dia bolt 150mm long grouted in brick wall/concrete including making good the distrubed sufaces as original complete all as directed. Note : The measurment shall be taken of from elevation and not girthwise.

M & L for TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified and directed.

M & L for TMT bars 6mm to 8 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified and directed.

S & F in repair for stainless steel drapery rod of 25 mm inner dia (in lengths as directed) of approved colour with and including decorative finial at both ends and pair of powder coated mild steel brackets fixed at both ends with PVC rawl plug and steel screws on walls/beam, including PVC curtain rings of matching colour @ 10 cm C/C complete all as specified and directed.

M&L for RCC type B-1, 1:2:4 (using 20 mm graded broken stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, shelves and the like complete all as specified and directed.

M&L for RCC type B-1, 1:2:4 nominal mix (using 20 mm graded broken stone aggregate) as in chajjas and the like complete all as specified and directed.

M&L for 25 mm thick PCC type B-0, 1:2:4 (using 12.5 mm graded stone aggregate) as in under floor tiles finished the surfaces even and fair complete all as specified and directed.

M & L for 50mm thick PCC 1:3:6 , type C-1 using 20 mm graded stone aggregate as in plinth protection laid in slope in 1:30 in alternative bays not exceeding 2 mtr in length. Exposed surfaces finished even and smooth without using extra cement including raking out joints between panel to panel and panel to wall and plugging the same with bitumen mastic using bitumen and sand mixture in 1:3 complete all as specified and directed.

M & L for machine cut Kota stone slab 20 to 25mm thick size not less than 22" x 22" as in floor laid & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing over and including screed bed or bedding layer of 20mm thick in CM 1:6 for laying floor finishes complete all as specified and directed.

M & L for 20-25mm thick machine cut Kota stone as in riser such as steps, skirting, dado and pillar set etc over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing over and including10mm thick cement plaster in CM (1:4) on other than fair faces of brick work of stone surfaces of walls complete all as specified and directed.

M&L 16-18mm thick granite 'Z' black colour (table rubbed and polished) as approved by GE in steps, jambs pillars, window cills, cooking platforms and like jointed over and including 20mm thick screed bed or bedding layer in cement sand mortar 1:6 and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

M & L rounding the edges of stone slabs one edge, such as in steps, cooking plateform and other similar situations, complete all as specified and directed.

M & L drilling holes for pipes etc. in cooking platform stone slab including RCC slab n exc. 25mm dia and exc. 100mm depth, complete all as specified and directed.

M & L for 10mm thick rendering internal surfaces in CM 1:6 on other than fair faces of brick work or stone masonry surfaces of walls, finished even and fair without using extra cement, complete all as specified and directed.

M&L screed bed or bedding layer of mortar, 15mm thick, in cement mortar 1:4, mixed with liquid water proofing admixture as per manufacture instructions on concrete surfaces of roof slab finishing the surfaces even and smooth complete all as specified and directed. Note : Water proofing Admixture shall be measured and paid separately.

M&L 15mm thick rendering on fair faces of brick or concrete in cement & sand mortar 1:4 mixed with water proofing admixture as per manufacture instructions, finished the surface even and smooth complete all as specified and directed. Note:- WPA shall be measured and paid separately under relevant item of this Schedule.

M & L Extra over rendering or plastering for work in isolated widths or in width not forming part of general plastering such as in bands, sunk panel, cornices, skirting, drip moulds and similar work exc. 15cm but n.exc. 30cm in width or girth, including cutting to edges, all mitres and stopping ends etc complete all as specified and directed by Engineer-in-Charge.

M & L for rendering 5mm thick in CM 1:3 over ceiling (sunshed, chajjas etc.) finished even and smooth without using extra cement complete all as specified and directed.

M&L 450x300x7-8 mm thick glazed ceramic coloured tiles, jointless, as in vertical surfaces such as skirting or dado set & jointed in neat cement slurry & pointed in white or coloured coloured cement to match the shade of tiles over and including 10mm thick cement plaster in CM 1:4 complete all as specifed and directed.

M & L for non skid ceramic tiles (coloured) 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm as in floors and including 15mm thick screed bed in CM 1:6 laid on floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles complete all as specified and as directed.

M & L for non skid ceramic tiles (coloured) 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm as in floors and including 10mm thick screed bed in CM 1:4 laid on floors etc. including necessary cutting of tiles as required size, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles complete all as specified and as directed.

M & L for non skid ceramic tiles (coloured) 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm as in floors and including 15mm thick screed bed in CM 1:6 laid on floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles complete all as specified and as directed.

Peparation of steel surfaces and iron surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete alcomplete all as specified and directed.

Preparation old painted steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint, complete all as specified and directed.

Preparation of newly wooden surfaces or old untreated wooden or wood based surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint of approved shade over one coat of pink primer complete all as specified and directed.

Preparation of old or previously treated wooden or wood based surfaces of any description over 10 cm in width or girth and applying one coat of synthetic enamel paint of approved shade complete all as specified and directed.

Preparation of old plaster surfaces by washing rubbing down and stopping of plastered surfaces and applying two coats of cement based paint white or tined on walls including cornices etc. complete all as specified and directed.

Preparing newly plastered surfaces and applying three coats of white wash on ceiling complete all as specified and directed.

Preparing newly plastered surfaces and applying two coats of white wash on ceiling complete all as specified and directed.

Preparing newly plastered wall surfaces and applying three coats of white wash, complete all as specified and directed.

Preparing old decorated surfaces of walls and applying two coats of white wash, complete all as specified and directed.

Preparation of newly plastered surfaces of wall and applying two coats of distemper oil emulsion over one coat of alkali resistant primer complete all as specified and directed.

M&L complete removal of existing treatment on old plastered surface of wall, applying 2mm thick wall care putty to achieve smooth surface of walls and applying two coats of oil bound distemper complete all as specified and directed.

Preparing newly plastered surfaces of walls and applying two coats of cement based paint complete all as specified and directed.

S&F steel water tubing, galvanized, medium grade, with all fittings, fixed to walls and ceiling or in floor complete all as specified and directed for following sizes:-

15mm bore.

20mm bore.

Refixing of old steel water tubing , galvanized, medium grade, with all fittings, in new or old position (Walls, ceiling. Floors etc.) bore of pipe complete all as specified and directed for following sizes:-

15mm bore.

20mm bore.

S & F 500 litres, rotational moulded polyethylene water storage tank (Cylindrical vertical with closed top), hoisted and fixed in position and including 20mm PTMT float valve complete all as specified and directed. Note : PVC tanks shall be ISI marked and having two layers.

S & F in repairs 20 mm bore Gun Metal globe or gate valve, with iron wheel head, screwed both ends for iron pipe and fixed, complete all as specified and directed.

S & F in repairs 20mm bore Ball Valves, high pressure, PTMT with epoxy coated Aluminium rod and high density plastic ball screwed for iron piped and fixed in position, complete all as specified and directed. Make:- PRAYAG or equivalent as specified in Appendix 'D'.

S & F in repair 15mm bore bib tap cast copper alloy fancy type chromium plated long body/short body with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule and fixed, complete all as specified and directed.

S & F in repairs 15mm bore stop valve/angle valve cast copper alloy chromium plated, fancy type screwed down high pressure long shank and cup concealed type with crutch or butterfly handle screwed both ends for iron pipe or for union complete all as specified and directed.

S & F brass chromium plated tubular towel rail, 20mm dia, “D” type, 60cm long between flanges, fixed with chromium plated brass screws complete all as specified and directed

S & F PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors including taking out old unserviceable PVC/CI Pipe, complete all as specified and directed for following sizes:-

75mm bore.

110mm bore.

S & F PVC (SWR) pipes single socketed in any length fixed to walls with holder bat clamps of GI flat iron 25x3mm including taking out old unserviceable PVC/CI Pipe complete all as specified and directed for following sizes:-

75mm bore.

110mm bore.

S & F PVC(SWR) bend of any radius complete all as specified for following sizes:-

75mm bore.

110mm bore.

S & F PVC (SWR) junction single, (single T) equal or unequal with oval access door complete all as specified and directed of following sizes:-

75mm bore.

110mm bore.

S&F in repair brass chromium plated shower rose 125mm size with swivel joint type including fixing to steel pipe of 15mm bore or union, complete all as specified and directed.

S & F PVC (SWR) vent cowl for 110 mm bore of pipe complete all as specified and directed.

S & F in repairs PVC (SWR) floor trap 75mm dia outlet plain with grating including jointing with solvent cement complete all as specified & directed.

S & F in repair grating doom 100 mm dia of PTMT (minimum weight 25 gms) fixed with cement, complete all as specified and directed.

S&F 110mm PVC (SWR)/ WC connector beny type, complete all as specified and directed.

Use and waste of formwork to soffits of suspended slab such as roof slabs, floor slab n.exc 200mm thick (Horizontal or sloping) complete all as specified and directed.

Use and waste of formwork to sides and soffits of chajjas for fair finished surfaces complete all as specified and directed.

Use and waste of formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 5cm but not exc.10cm wide complete all as specified and directed.

S & F in repairs sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm including CP waste coupling complete all as specified and as directed .

S & F stainless steel kitchen utencil rack over all size 30"x31"x10" and thickness of stainless steel plate 0.60mm fixed to wall with stainless steel screws complete all as specified and as directed. Make:- Blue star/Nirali/Silver shine/Prayag.

S & F in repairs vitreous china wash basin, flat back, size 550 x 400 mm including one No PVC waste pipe 25 mm dia and 75 cm long with 32 mm dia connector, 32mm size waste fittings, brass chromium plated with long screwed shanks and fly nuts, flange end, bedded in red lead cement and other fixed and PVC connection 15mm dia 600mm long with two Nos check nut and washer, complete including cutting for and pinning in ends of bracket or erecting stand complete all as directed.

S & F 32mm dia high density polythyelene (HDPE) pipes of pressure rating 6Kg/ sq cm laid in floor or fixed to walls including taking down old pipes, complete all as specified and directed.

S & F 40mm dia high density polythyelene (HDPE) pipes of pressure rating 6Kg/ sq cm laid in floor or fixed to walls including taking down old pipes, complete all as specified and directed.

Supply only 15 mm bore pillar tap, chromium plated, fancy type, screwed down high pressure with crutch handle with or without lettered ‘Hot ‘ or ‘cold’ with long screwed shank and fly nuts screwed for iron pipe complete all as specified and directed.

S & F repairs 15 mm bore chromium plated, wall mixer for mixing hot and cold water fancy type complete all as specified and directed.

S & F in repairs vitreous China squatting pan (Orissa pattern) water closet (white) of size 580 mm x 440 mm with integral foot rests, 'P' or 'S' trap, including connection to trap, flushing pipe and antisyphonage pipe etc and including provision of PCC (1:5:10) type E-2 lean concrete in filling, making good to floor (excluding flushing cistern and flush pipe etc) complete all as specified and directed.

S&F in repairs, PVC low level cistern 10 litres capacity, valve less, symphonic action type with float, handle including 32mm dia PVC flush pipe of polyethylene of low or high density & bracket etc complete all as specified and directed.

S & F in repairs PVC connection pipe,15mm size with PTMT nuts of length 450mm with adopter and washer at both end complete all as specified and directed.

M & L cutting and punning in brick walls for cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting exc 10 cm girth but not exc 20 cm girth complete all as directed.

Supply and fix APP polymeric water proofing membrane, minimum 3mm thick and weighing not less than 3.0 Kg/Sqm of make super thermolay manufactured by STP Ltd or ‘Hyper Plas’ (Polyster) manufactured by M/S IWL Ltd or ‘Shaliplas’ (polyester) manufactured by M/S Capital Steels and chemicals Pvt Ltd or Hydro Stop manufactured by TIKITAR DANOSA (INDIA) Pvt Ltd as approved by GE, black finish reinforced with non-woven polyester matt, with a thermo fusable finish laid over compatible bitumen primer (Bitumen primer shall be TANK MASTIC of M/S STP Ltd or ‘EMW FLATE’ of M/S Texas India Ltd} at the rate of 0.40 Kg/Sqm torching overlaps with a propane or a butane gas torch, with a overlap of 75mm at the sides and 100mm at the ends and sealing including applying a coat of cold emulsion bituminous primer all as per manufacturer’s instructions complete all as directed. Note: (i) Coved fillets in PCC(1:2:4) type B-0 using 12.5mm graded stone aggregate, of radius 75mm shall be provided at the junction of roof and parapet wall/mumty/chimney/other vertical surfaces and thereafter surface painted with hot paving bitumen of Grade 30/40 confirming to IS-73, [email protected] Kg/Sqm over a coat of bituminous primer confirming to IS-3384 applied @ 0.40 Kg/Sqm. (ii) Polymeric membrane shall be taken to a height of 45cm (minimum) and then inserted inside the groove of parapet wall of brick masonry and shall be finished by a membrane flushing. (iii) The waterproofing treatment shall be got carried out by the manufacturer or their authorized applicators. (iv) In case of stone masonry parapet wall etc a groove of size 25mmx25mm(minimuim) shall be made in coved fillet at the junction of roof and parapet wall/mumty Chimny/other vertical surfaces and polimeric membrane insterted in groove and sealed with paving bitumen. (v) Exposed surfaces of APP membrane shall be applied with one coat of bituminous aluminium paint @ 150 ml/Sqm. (vi) Above aspects are deemed to be included in quoted rate.

M & L for repairs to sunken floor slab with following specifications: - (i) Roughening surfaces of old concrete floor and wall by picking sweeping clean and washing down with water to remove dust etc. (ii) PCC 1:2:4, type B-0, using 12.5mm graded stone aggregate 50mm thick (average) as in sunken floor with proper slope towards GI spout. (iii) Providing 15mm thick cement plaster in cement mortar 1:3 mixed with water proofing admixture as per manufacture's instructions over bottom and vertical surfaces contact with sunken slab, finishing the surface even and smooth using extra cement. (iv) Damp proof course on horizontal surfaces with scrapping and properly cleaning the surface to remove loose particles & applying one coat of self priming (33% dilution) and two coats of undiluted material with @ 10.67 ltrs per 10 sqm as Damp Proof for water proofing and Damp proof course on vertical surfaces scrapping and properly cleaning the surface to remove loose particles and applying one coat of self priming (33% dilution) and one coats of undiluted material with @ 4.85 ltrs per 10 sqm. Damp proof for water proofing. Make of DPC solution :- Asian/ STP/ Choksey/Pidilite. (v) Brick bats filling under sunken floor. (vi) PCC 1:3:6, typpe, C-2, using, 20mm graded stone aggregate 75mm thick, over brick bats filling as in subbase to receive tiles. Note:- For payment purpose only floor area shall be measured.

E/M PORTION Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete including teak wood battens or from existing conduits with all fittings, such as switches, ceiling rose, pendants, sockets, lamp holder, fan regulators, sketch/brackets light fittings (except tube light fitting) etc but excluding ceiling fan and removal of old material from site (except fittings to be reused) and making good disturbed surfaces of walls, floors ceiling etc complete all as specified and directed to match with existing surfaces.

M & L for point wiring complete with 1.5 Sqmm single core multistranded copper conductor of 1100 volts grade PVC insulated and unsheathed FRLS cable enclosed in and including PVC casing and capping double locked box type with accessories fixed on surface of walls/ceiling by means of PVC sleeves/dash thru fasteners with cadmium plated screws all as per IS with MS concealed terminal boxes (Heavy duty) with 3mm thick plastic laminated bakelite (Hylam) sheet top cover for mounting switches, sockets, regulators, bell push etc, including 1.5 Sq.mm solid copper conductor with green PVC FRLS insulated unsheathed earth continuity conductor to common earth & connecting to earth dolly for the following :-

One light point controlled by one, one way switch.

One fan point controlled by one switch and regulator.

One bell/buzzer point controlled by one bell push.

One light point controlled by two, two way switch.

One 3 pin, 5/6 Amps socket outlet controlled by one 5/6 Amp switch on same board.

One 3 pin, 5/6 Amps socket outlet controlled by one 5/6 Amp switch on independent board.

M & L for point wiring complete for one 3 pin 15/16 Amps socket outlet controlled by one 15/16 Amps switch on indepdent board with 2.50 Sqmm single core multistranded copper conductor of 1100 volts grade PVC insulated and unsheathed FRLS cable enclosed in and including PVC casing and capping double locked box type with accessories fixed on surface of walls/ceiling by means of PVC sleeves/dash thru fasteners with cadmium plated screws all as per ISS with MS concealed terminal boxes (Heavy duty) with 3mm thick plastic laminated bakelite (Hylam) sheet top cover for mounting switches, sockets, including 2.50 Sq.mm multistranded copper conductor with green PVC FRLS insulated unsheathed earth continuity conductor to common earth & connecting to earth dolly.

S & F switch piano flush type 5/6 Amps, single pole, one way, 230 Volts complete all as specified and directed.

S & F switch piano flush type 5 Amps, single pole, two way 230 Volts complete all as specified and directed.

S & F switch piano, flush type single pole, one way 15 Amp, 230 Volts complete all as specified & directed.

S & F socket outlet, 3 pin (with 2 pin outlet also), 5/6 Amp, flush type, 240 Volts complete all as specified & directed.

S & F socket outlet two-in-one, 3 pin, 5 Amp and 15 Amp, flush type, 240 Volts complete all as specified & directed.

S & F bell push, flush type, 5 Amp, 240 volts complete all as specified & directed.

S&F bell/buzzer AC 230 volts, single pole, complete all as specified and directed.

S & F ceiling rose, surface bakelite 65mmx50mm with two or three terminal complete all as specified and directed.

S & F lamp holder, PVC / polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

S & F electronic stepped type fan regulator, flush type, connecting up, ISI marked, complete all as specified and directed.

S & F sheet metal enclosure double door DB SPN 8 way, 240 volts protection class IP-43 made out of CRCA mild steel sheet surface with epoxy powder coated surface confirming to IS-13032, IS 8623, BS-5484 with tinned copper bus bar of 200 Amps capacity all as specified and directed.

S & F sheet metal enclosure single door DB SPN 04 way, 240volts protection class IP-30 made out of CRCA mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mounted confirming to IS-13032, IS 8623, BS-5484 with tinned copper bus bar of 200 Amps capacity complete all as specified and directed.

S & F sheet metal enclosure single door DB SPN 02 way, 240 volts protection class IP-30 made out of CRCA mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mounted confirming to IS-13032, IS 8623, BS-5484 with tinned copper bus bar of 200 Amps capacity complete all as specified and directed.

S & F MCB SPN 32 Amps, 240 volts, B-curve, rupturing capacity 10KA conforming to IEC-60898, Part-I, complete all as specified & directed.

S & F MCB SPN 63 Amps, 240 volts, B-curve, rupturing capacity 10KA conforming to IEC-60898, Part-I, complete, all as specified & directed.

S & F MCB SP 6 to 32 Amps, 240 volts, B-curve, rupturing capacity 10KA conforming to IEC-60898, Part-I, complete, all as specified & directed.

S & F for submain wiring with 2 single core PVC insulated & PVC unsheathed FRLS cable 1100 Volt grade with 06 Sqmm copper multistranded conductor drawn through and including PVC conduit 25mm bore fixed on surface to wall/ ceiling by means of MS screws and saddles including one run of 6 Sqmm single core multistranded copper conductor 1100 volts grade PVC insulated and unsheathed FRLS cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed. Note: - Two runs of main cable, one run of earth continuity conductor and one run of conduit will be measured and paid as one length only.

Supply and fixing Adore LEMP Lamp of 9/10 watt including taking down old unserviceable CFL lamp, complete all as specified and directed. Make & Model :- Cat Part No LHLDERHEML8X010 of make Havells or equivalent model of make as specified in Appendix 'D'.

Supply and fixing in repair LED street light fitting 20 Watt 230 V, 50 Hz DRACO Series , lightand connecting the fitting from using copper flexible cord of size 1.5sqmm, 3 core of suitable length complete all as specified and directed. Make & Model :- Cat Part No LTESS20WLED of make C & S or equivalent model of make as specified in Appendix 'D'.

Supply and fix in repair decorative ultra slim linear profile LED tube light fittings, fixture 18 Watt 230 V, 50 Hz with extruded polycarbonate, environmental friendly, energy efficient ready to use pack complete with all standard fittings etc pre-wired including LED tube and connecting the fitting from ceiling rose/connector using copper flexible cord of size 1.5sqmm, 3 core of suitable length complete all as specified and directed. {Model/Make : Cat Part No LHEXBLP7PN1W018 E-LITE LED PRIDE PLUS of make Havells or equivalent model of make Crompton Greaves Ltd/ Surya Roshni Limited / Shakti Fixtures Pvt Ltd/ Syska LED Lights Pvt Ltd (SYSKA)}.

S & F in repair second class hardwood rectangular block open recessed of size 30cm x 25cm x 5 cm depth with 3 mm thick phenolic laminated sheet top cover fixed with suitable steel screws & PVC rawl plug (4 Nos) for DB complete all as specified and directed.

Supply and Laying/ fixing, jointing, testing and commissioning of 16sqmm 2 core LT under ground cable 1100 volts grade XLPE insulated & PVC sheathed cable heavy duty armoured, with multistranded aluminium conductor laid in trenches/ ducts, through pipe, under floors or roads/ pipes/fixed on walls/poles including taking down old unserviceable cable complete all as specified and directed. Note :- (i) Sand cushioning, cable protection, GI pipe for protection and excavation & earth work shall be measured & paid for separately. (ii) Road cutting involved during excavation for laying of cables etc shall be made good as per existing road. Nothing extra shall be admissible on this account. Quoted rates of the item shall be inclusive of the above provisions.

Excavation in trenches not exc 1.5m wide and not exc 1.5m in depth for foundation, for laying pipes/cables etc or for wells, shafts, manholes etc not exc 10 Sqm on plan and getting out, in soft/loose soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cms thick in soft / loose soil complete all as specified and directed.

Removal of excavated surplus spoil/ material to a distance n.exc 50m and depositing where directed at level not exceeding 1.5 m above the starting point,complete, all as specified & directed.

M & L for brick protection for UG XLPE cable with burnt clay FLY ASH bricks, as per IS-13757 1993) old size laid dry and flat abutting each other with gaps between adjacent brick 10mm with width equal to length of brick in trenches across the cable complete all as directed.

M & L for dry sand cushioning to PVC under ground cable with screened and washed sand and punning to provide a required cover complete all as specified and directed. Note :- Thickness after punning shall be considered for payment.

Supply and fixing cubical metallic box of size 1.0 mtr x 0.9 mtr x 0.30 mtr depth shall be dust and vermin proof IP-51 class protection and made out of 2 mm thick CRCA MS steel sheet, front openable double door type with locking arrangement with and including 3 mm thick plain sheet clear glass of suitable size fixed to facilite meter reading, all internal and external steel surfaces painted with two coats of synthetic enamel paint over a coat of red oxide primer, internal wiring with PVC insulated single core multistranded copper conductor FRLS cable IS - 694 marked of adequate size but not less than 6 Sqmm with proper ferrule and cable gland, box shall be fixed on wall with 'Anchor' type fastner type bolts and nuts (set of 6 bolts of 12 mm dia 200 mm long with nuts and washers ) grounted into the wall properly to hold the box, writing MES/Qtr No for each energy meter with thick white synthetic enamel paint, neoprene rubber gasket shall be provided for proper sealing, including box shall have arrangement for fixing electic energy meter - 04 Nos, MCB DB SPN 2 way - 4 Nos, MCB DB SPN 4 way - 01 No, complete all as directed. Note :- (i) Existing electric meters - 04 Nos will be taking down carefully and refixing the same inside the new meter box carefully including necessary electric connections and sealing the electric meter and MCB DB SPN 4 Way - 01 No and MCB DB SPN 2 Way - 4 Nos shall be measured and paid for separately under relevent items of this BOQ.

M & L for earthing complete with galvanized steel earth plate 60 cm X 60 cm X 6.3 mm thick buried vertically in ground to depth not less than 2.25 metres deep below ground level, with top edge of earth plate not less than 1.5 m below ground level, connected to galvanized earth lead wire 4.00mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel besides welding at all joints as shown in drawing and including excavation and earth work, GI pipe light grade 40mm bore for protection of strip and connected to continous earth lead on pole/test point, supplying and laying charcoal dust common salt PCC 1:2:4 type B1, chamber and MS angle iron frame 40x40x3mm and RCC cover 40mm thick (1:2:4) type B1 using 20mm graded stone aggregate reinforced with 6mm dia round bars @ 75mm C/C both ways with MS handle 12mm dia, PGI funnel and wire mesh, 20mm dia GI pipe medium grade for watering all as shown in electrical plate No 5 on srl page No 497 of SSR Part I (2009) drawing and connection to earth test point including testing and including dismantling and taking out old earthing complete all as specified and directed. Note : (i) The cost of earth lead /strip and GI pipe for protection of earth lead/strip upto 7.5m is included in the quoted rate. (ii) The cost of excavation, earth work is included in the quoted rate.

UNIQUE INDIA CONSTRUCTIONS