REPAIR/MAINT OF DG SETS AND ALLIED SERVICES AND REPAIR/MAINT OF MISC EXTERNAL ELECTRIC SYSTEM AT BAREILLY CANTT UNDER GE (W) BAREILLY

Amount

General servicing of DG Set including B check, cleaning of machine, replacement of oil filter, fuel filter and air filter) cleaning of fuel tank, checking of oil level, checking of tension in fan belts, checking and repair of leakages in hose pipe, proper adjustment of tappet, checking of Governor control assembly, radiator, complete all as per manufactaures recommendations for the following capacity and make of DG sets:- Note: Cost of all filters and Engine oil shall deemed to be included in the quoted rate of this item.

(a) 125 KVA Cummins / Kirloskar DG Set

(b) 500/600 KVA Jackson Kirloskar DG Set

(c) 63/62.5 KVA Kirloskar/Ruston/Ashoka Leyland DG set

(d) 20/40 KVA DG set Make : Kirloskar

(e) 15/10/7.5 KVA DG set Make : Kirloskar

Dismantling / stripping diesel engine of DG Det of 63/40 KVA rating capacity after separating alternator from common base frame setting a side for repair/replacement of all components/accessories including preparation of list of spares which are ascertained to carry out repair /replacement of detained inspection complete all as specified and directed. Note :- Spares shall be measurd & paid separately under relevent items of this schedule.

Supply and fixing of the following spares for DG Set 63/40 KVA Make- Kirloskar / Ashoka as required to be replaced under relevant item here in before complete all as specified and directed :-

(a) Piston stud size Cat Part No. as existing.

(b) Piston Ring Cat Part No. as existing.

(c) Piston Pin Cat Part No. as existing.

(d) Cylinder liner (Sleeve) Cat Part No. as existing.

(e) Exhaust valve Cat Part No. as existing.

(f) Inlet valve -Cat Part No. as existing.

(g) Packing kit Cat Part No. as existing.

(h) Oil Seal Cat Part No. as existing.

(j) Oil Pressure guage Cat Part No. as existing.

(k) Kit "O" Ring Cat Part No. as existing.

(l) Fuel flexible pipe Cat Part No. as existing.

(m) Oil Filter with gasket Cat Part No. as existing.

(n) Diesel filter with gasket Cat Part No. as existing.

(o) Connecting Rod bush Cat Part No. as existing.

(p) Thrust washer Cat Part No. as existing.

(q) Valve guide inlet and outlet seat Cat Part No as existing

(r ) Cylinder Head Gasket Cat Part No as existing

(s) Packing kit.Cat Part No as existing

(s) Fuel injection pipes.Cat Part No as existing

(t) Air Filter Cat Part No as existing

(u) Primary element

(v) Stop Solenoid

Dismantling / stripping diesel engine of DG Det of 125 KVA rating capacity after separating alternator from common base frame setting a side for repair/replacement of all components/accessories including preparation of list of spares which are ascertained to carry out repair /replacement of detained inspection complete all as specified and directed. Note :- Spares shall be measurd & paid separately under relevent items of this schedule.

Supply and fixing of spares for DG Set 125 KVA Make Kirlosker, Cummins as required to be replaced under relevant item here in before complete all as specified and directed .

(a) Piston stud size Cat Part No. as existing.

(b) Piston Ring Cat Part No as existing.

(c) Piston Pin as existing.

(d) Cylinder liner 22001-40847

(e) Exhaust valve Cat Part No as existing

(f) Inlet valve Cat Part No as existing

(g) Packing kit (Gasket) Cat Part No as existing

(h) Oil Seal Cat Part No as existing

(j) Oil Pressure guage (Precell) Cat Part No as existing

(k) Kit "O" Ring 7B -Cat Part No as existing

(l) Fuel flexible pipe Cat Part No as existing

(m) Oil Filter B-Cat Part No as existing

(n) Diesel filter Cat Part No as existing

(o) Connecting Rod assembly make kirloskar cat part no 4200910000

(p) Thrust washer YD -Cat Part No as existing

(q) Valve guide inlet and outlet seat Cat Part No as existing

(r) Cylinder Head Gasket / packet kit.

(s) Fuel injection pipes.

(t) Valve Solenoid

(u) Air Filter Cat Part No as existing

Re-assembling the diesel engine after top overhauling and installation in its original place/position including testing commissioning of DG Set complete all as specified and directed of following capacities:-

(a) DG Set 63/40 KVA cap Make Kirloskar

(b) DG Set 125 KVA cap Make Kirloskar/Cummins

Griding, polishing of cylinder head, cylinder valve seats, valve guide etc all as required for best overhauling for DG Set 63/40 KVA Make- Kirloskar/Ruston complete all as specified and directed

Griding, polishing of cylinder head, cylinder valve seats, valve guide etc all as required for best overhauling for DG Set 125 KVA Make- Kirloskar/Cummins complete all as specified and directed

Overhauling, servicing/calibration of FIP (fuel injection pump) assembly of DG Set 125/63/40 KVA Make: Kirloskar/Ruston including replacement of nozzle /injection delivery valve holders benjo bolt copper washer roater bearing etc including testing complete all as specified and directed.

Suppy and fixing following spares parts of FIP of DG Set 63/40 KVA Make: Kirloskar/Ruston complete all as specified and directed (only unserviceble parts shall be replaced after inspection):-

(a) Elements of FIP (Make MICO 1200240183)

(b) Nozzle (-do-) 1267230814

(c) Plunger

(d ) Delivery valve (-do-) 14185220471 HP

(e) Benjo Bolt (-do-) 29112037051 HP

(f) Seat Washer

(g) Bearing

(h) Tappet roller bush pin

(j) Control Rod 1416024007

(k) Fly weight assembly

(l) Governer spring

(m) Packing/Gasket 1411015052

Suppy and fixing following spares parts of FIP of DG Set 125 KVA Make: Kirloskar/Ruston complete all as specified and directed (only unserviceble parts shall be replaced after inspection):-

(a) Elements of FIP (Make MICO 1200240183)

(b) Nozzle (-do-) 1267230814

(c) Plunger

(d ) Delivery valve (-do-) 14185220471 HP

(e) Benjo Bolt (-do-) 29112037051 HP

(f)Seat Washer

(g) Bearing

(h) Tappet roller bush pin

(j) Control Rod 1416024007

(k) Fly weight assembly (MICO) 1428194000128

(l) Governer spring

(m) Packing/Gasket 1411015052

(n) Coolant for radiators

Overhauling, servicing/calibration of PT(Pressure Time) pumps assembly and Injector of DG Set 125 KVA Make: Cummins including replacement of Gear Pump /Pulsation Damper/ Teco Shaft/Main shaft and injector parts, Fly weight assembly bearing etc including testing complete all as specified and directed.

Suppy and fixing following spares parts of PT pumps and Injector of DG Set 125 KVA Make: Cummins complete all as specified and directed (only unserviceble parts shall be replaced after inspection):-

(a) Gear Pump

(b) Main Shaft

(c) Techo Shaft

(d) Throttle Shaft

(e) Fly Weight assembly

(f) Pulsation Damper

(g) Bearing

(h) Filter screen

(j) Seal

(k) Packing/Gasket Set

(l) Barrel Plunger aasembly of Injector

(m) Injector Cup of Injector

Supply and fixing of the following spares for DG Set 500/600 KVA Make- Jackson Kirloskar complete all as specified and directed :-

(a) Oil Cooler Gasket

(b) Oil Pan Gasket

(c) Cylinder Head Gasket

(d) Cylinder Head Cover Gasket

(e) Water pump Gasket

(f) Exhaust Manifold Gasket

(g) Intake Manifold Gasket

(h) 'O' ring Kit

(j) Fan V Belt

(k) Water Pump V Belt

(l) Bearing

(m) Cooling Nozzle

(n) Thermostat

(o) Impeller Water Pump

(p) Sensor Tech complete

(q) Water Separator

Supply , installation , commissioning and testing of Governor Controller Assembly complete Model - DWC-2000 Cat part No 65.11220.7008 CE certified . For 500 KVA DG sets Make - Jackson Kirlosker

Supply , installation , commissioning and testing of Digital Display Controller card complete for Electric Control Panel of 500/600 KVA DG sets Make - Jackson Kirlosker

Supply , installation , commissioning and testing of Electric Actuator Assembly complete for 500 KVA DG sets Make - Jackson Kirlosker

Supply , installation , commissioning and testing of self starter 24 Volt make Doosan or equilavent as per sample for DG Set complete for 500/600 KVA DG sets Make - Jackson Kirlosker

Supply , installation , commissioning and testing of Priming Pump complete for 500 KVA DG sets Make - Jackson Kirlosker

Supply , installation , commissioning and testing of Relief Valve assembly complete for 500 KVA DG sets Make - Jackson Kirlosker

Dimantling of FIP (fuel injection pump) assembly and FIP nozzles, Reassembling after repairing and calibration ,setting injection timing to aasure smoke less operation of DG Set 500/600 KVA Make: Jackson Kirloskar complete all as specified and directed.

Repairing/servicing/calibration of FIP (fuel injection pump) assembly of DG Set 500/600 KVA Make: Jackson Kirloskar including replacement of all unserviceable spare parts for 10/12 nos of cylinder engine of DG set including testing complete all as specified and directed.

Repairing and calibration of FIP Nozzle of DG Set 500/600 KVA Make: Jackson Kirloskar including replacement of all unserviceable spare parts for 10/12 nos of cylinder engine of DG set including testing complete all as specified and directed.

Opening of Cylinder Head , tappings , Griding, polishing of cylinder head, cylinder valve seats, valve guide etc and reassembling including tappet setting testing and trial complete all as required for best operation for DG Set 500/600 KVA Make- Jackson Kirloskar complete all as specified and directed

Rectification of water contamination i.e. water entering in Oil Chamber including replacement of seals and gaskets and nut bolts etc complete all as specified and directed

Repair of Governor Controller including setting and adjustment of Droop speed mode control Fuel control , stability controll, over speed control and testing complete of DG set Cap 500/600 KVA DG set Make- Jackson Kirloskar

Repair of Electric Control Panel of DG set of cap 500/600 KVA DG set Make- Jackson Kirloskar

Supply and fixing in replacement of Relay Card with Relay complete of Electric Control Panel of DG set of cap 500/600 KVA DG set Make- Jackson Kirloskar

Dismantling of radiator of DG Set 40 KVA/ 63 KVA / 125 KVA Make Kirloskar/ Ruston/Cummins complete all as specified and directed.

Repairing of radiator 40KVA/ 63 KVA / 125 KVA DG Set of make Kirloskar/ Ruston by brazing, soldering and cleaning of fins and descaling of tubes, replacement of new hose pipe set with clamp and fixing in original position and testing complete all as specified and directed.

Supply and fixing including testing of radiator core of copper for 63 KVA DG set Make- Ashoka Leyland/Kirlosker/Ruston as per sample complete alla s specified and as directed.

Supply and fixing including testing of radiator core of copper for 125 KVA DG set Make- Cummins as per sample complete alla s specified and as directed.

Dismantling unserviceable self starter 12 Volts of following capacity DG set of Make Kirloskar/ Ruston/Cummins and repair/maint by replacement of worn out parts like bendix pinion, piston, bush housing armature field coil, carbon bushes etc and refixing and testing for following cpacity complete all as specified and directed.

(a) 63 KVA & 40 KVA

Supply , installation , commissioning and testing of self starter 12/24 Volt make lucas/Bosch or equilavent as per sample for DG Set complete for 125 KVA DG sets Make - Kirlosker,Cummins

Supply , installation , commissioning and testing of self starter 12 Volt make lucas/Bosch or equilavent as per sample for DG Set complete for 63/40/20/10 KVA DG sets Make - Kirlosker,Cummins, Ruston

Dismantling, broken terminal shaft with MS cover for alternator of DG Set of any make /capacity and supply and connecting new terminal plates and cover of 1 mm thick MS sheet for alternator including cable connection complete all as required at site to complete the job as per approved sample complete all as specified and directed.

Dismantling of alternator from engine and stripping /opening replacement /rewinding the alternator with copper super enamelled wire of existing size and A class insulation for 63/125 KVA alternator make Kirloskar /Cummins /Crompton and refixing after alignment complete all as specified and directed.

S & F rectifier for DG Set 63/125 KVA cap Make Kirloskar complete all as specified and directed.

S&F Hour Run M/ Hour Meter including RPM Meter cable connection through Engine by making provision as necessary as per site requirement complete all as specified and directed.

S &F of turbo charger repair kit make ; Garrett Cat Part No. 0612321000 for 125/63 KVA DG Set Make - Kirloskar complete all as specified and directed.

S & F Core assembly of turbo charger Make Garrett complete all as specified and directed.

S & F Turbo charger garrett for kirloskar DG Set complete all as specified and directed.

S & F diesel fuel flexible pipe for DG Set of any capacity / Make complete all as specified and directed.

S&F of oil pressure pipe as per sample Make : Ashoka Leyland complete all as specified and directed.

S & F hose pipe flexible Cat part AK 5040 SS of Make Cummins

S & F hose pipe flexible Cat part AK 6065 SS of Make Cummins

S & F Oil cooler for DG Set 63 KVA/125 KVA capacity of make Kirloskar complete all as specified and directed.

S & F Lubricating oil pump for DG set 63 KVA/100 KVA capacity of make : Kirloskar and testing complete all as specified and directed.

S&F in repair cut out 12 Volts automatic of make : Lucas/Bosch and testing complete all as specified and directed.

S & F ignition switch with replacement of auto wiring suitable for DG Set of any capacity make complete all as specified and directed.

S & F battery charger suitable for charging of battery 12 Volts 90/180 AH with charging current 0-10 Amps, input voltage 230 Plus complete all as specified and directed.

S & F alternator for battery charging 12 Volts 180 AH with pulley complete all as specified and directed.

S & F battery cables of following sizes complete all as specified and directed:-

(a) 78 " long (+)

(b) 78" long (-)

S & F battery terminal brass heavy duty complete all as specified and directed.

S & F of battery charging meter (0-30) range complete all as specified and directed.

S & F oil temperature gauge Make AE, Dass Mesh, Siemens complete all as specified and directed.

Supply only distilled water in 5 Litre Jericanes complete all as specified and directed.

S & F Anti vibration pad set for DG Sets as per site requirement complete all as specified and directed.

S&F Fan belt of following sizes complete all as specified and directed :-

Repair of Electric Panel of DG set capacity 125 KVA make- Kirlosker Bliss without any damage to the serviceable equipments complete all as directed.

Supply and fixing in replacement of following spares/parts of Electric Panel of DG set capacity 125 KVA make- Kirlosker Bliss

(a) Pro com controller

(b) Relay Card

(c) Oil safety controller

(d) Engine Temperature Safety controller

(e) Battery charger 24 Volts

(f) Connection plate

(g) Push button with NO NC

(h) Toggle switch

(j) CT(current transformer) 6500T/6600T

(k) Engine Harness

(l) Panel Harness

(m) OEM relay with base

(n) LED lamp

(o) Ampere meter

Repair/Maintenance of Automatic Voltage Regulator (AVR) of DG Set of Capacity 500 KVA/600 KVA installed at MH including replacement of all minor and major parts like Ics, Rectifier,diodes, capacitors, resistance, relay,Printed circuit board etc. and refix the same after complete repair and testing on load complete all as specified and directed.

Supply and fixing in replacement Automatic Voltage Regulator (AVR) of DG Set of Capacity 500/600 KVA of the existing make type and capacity and testing on load complete all as specified and directed. Make : as per existing/as recommended by OEM.

S&F in replacement Automatic Voltage Regulator (AVR) of DG Set of following Capacity. Make Cummins/Kirloskar/Ruston and testing on load, complete all as specified and directed. Note:- The AVR installation should be done through experienced electrician cum DG mechanic and the AVR should be capable of regulating and maintaining the desired Voltage rating after installation.

(a) DG Set 125 KVA

(b) DG Set 63/40/20 KVA

Supply and fixing Battery 12 Volt 88 AH Make: Exide/Luminous complete all as specified and directed

Supply and fixing Battery 12 Volt 150 AH Make: Exide/Luminous complete all as specified and directed

Supply and fixing Battery 12 Volt 180 AH Make: Exide/Luminous complete all as specified and directed

Repair/maintenance of DG sets of any capacity ranges from 10 KVA to 600 KVA and any make and Model by qualified DG Set mechanic cum electrician by testing of complete units, and panels and governor Control setting and voltage fluctuation rectification including testing of self starter and battery and AMF panel and control panel etc and find out/detect the faults by setting/adjustment and rectify the defects in situ by using required spares and repair jobs and cleaning / normal maintenance to the DG Set complete to make the DG set functional in all respect complete all as directed by Engineer-in-charge. Note: (a) Spare parts and repair jobs of DG sets are measured separately under relevant items. (b) Register must be maintained by the contractor for the jobs carried out during breakdowns attending complaints and rectification of faults. (c) In this item only breakdown faults will be measured as a job. Minor and other major repairs and periodical, general servicing and preventive maintenance will be not considered in this item it will be measured in the respective repair jobs/refixing of spares items sub part. (d) The complaint lodged regarding unserviceability of DG set must be attended by the qualified technician within 1 hour of complaint lodged and must be rectified on same day . A penalty of Rs 1000.00 per day will be deducted from the contractor dues if complaints not attended or not rectified in due time.

M&L for earthing complete with galvanised iron steel earth plate of size 600 x 600 x 3.15 mm thick burried directly in ground (earth pit not less 2.25 metre deep below ground level) with top edge of the plate not less than 1.5 metre below ground level connected to thick electrode and 32x6 mm GI strip as earthing by means of nuts bolts check nuts and washers made of galvanised iron or steel earth wire protected by galvanised iron pipe 15 mm bore (medium grade) and connected to main switch board or main control board as directed and including concrete pit in PCC (1:3:6) type C1 precast RCC cover slab 54 x 54 cm x 5 cm with reinforcement with 8 mm TMT bars @ 150 C/C with one handle and funnel for watering charcoal or coke and salt in alternate layers & necessary earth work in soft/loose soil complete all as shwon in electrical plate No 5 of SSR Part-I including testing on completion all as specified and directed.

Refilling of fire Extinguser ABC type of capacity 10kg (including monomonium phosphate and silicon and Pressure of nitrogen as required for 10 Kg) complete all as specified and directed. Note:-Cost of locking arrangement after refilling and painting work included in coated rate.

S & Fix in repair AMF panel for 125 KVA DG set complete all as specified and directed.

Rewinding of exciter coil of capacity up to 125 KVA DG set with copper wire complete all as specified and directed.

Rewinding of exciter coil of capacity 500/600 KVA DG set with copper wire complete all as specified and directed.

Repair of Trolley four wheel including welding work, Nut-bolt etc and including replacement of unseviceable Tyre of size 750/16 (4 Nos.) to make it serviceable complete all as specified and directed.

S & Fix on load Changeover switch 200 Amp Four Pole 415V Phase for LT panel complete all as specified and directed.

S & Fix on load Changeover switch 400 Amp Four Pole 415V Phase for LT panel complete all as specified and directed.

Notes for Item No 1.00 to 76.00: (i) Complaints pertaining to DG Sets shall be resolved by the contractor within 24 hours of getting complaints. In case of failure on the part of contractor to resolve to the complaints within stipulated time, a penalty of Rs 500.00 per day per complaint shall be imposed on the contractor. (ii) The contractor or his authorised representative shall report to the concerned JE E/M at 09:00 hours dailly on all working days to receive order/instructions of the work. A register shall be maintained to record all orders & instructions and their complaints and is to be signed by the contractor/his representative and the Engineer-in-charge/JE E/M concerned. (iii) Work done register to be maintained by the contrator.

MISC EXTERNAL ELECT

Dismantling / taking out old mild steel channel / angle iron as in cross arms fixed to electric poles complete all as specified and directed.

Dismantling / taking out insulator of any size / type from existing electric HT / LT lines complete all as specified and directed.

M&L for Pin type insulator of 65 mm dia and 100 mm high, porcelain, vitreous, white, borwn or green including one galvanised mild steel spindle , two galnvanised iron wahers and one galvanised iron nut complete all as specified and directed.

Dismantling / taking out old ACSR conductor any size from existing overhead lines including disconnection complete all as specified and directed.

M & L for stringing, stretching and than strengthening of overhead conductor (ACSR) of any size or type on existing LT pole including binding and jointing the conductor with and including 14 SWG binding wire complete all as specified and directed.

M & L for one coat of aluminium paint of approved quality including preparation of existing old painted surface of steel tubular poles LT complete alongwith flat iron clamps, bracing, cross arms etc. and writing number of poles with white synthetic enamel paint over a circular black painted base complete all as specified and directed.

Material and labour for Cutting of bushes and cleaning the area around the sub station including two pole/four pole structures premises complete all as specified and as directed.

S & F PVC (moulded polypropylene) line phase separator (for separating 5 Nos. of over head line conductors) of suitable length with 25 mm fly nuts and clamps suitable for 1100 volts grade LT electric lines complete all as specified and directed.

S & F PVC (moulded polypropylene) line phase separator (for separating 4 Nos. of over head line conductors) of suitable length with 25 mm fly nuts and clamps suitable for 1100 volts grade LT electric lines complete all as specified and directed.

S & F PVC (moulded polypropylene) line phase separator (for separating 3 Nos. of over head line conductors) of suitable length with 25 mm fly nuts and clamps suitable for 1100 volts grade LT electric lines complete all as specified and directed.

Excavation in trenches not exc. 1.50 m wide and not exc. 1.50 m in depth for laying cables and getting out in soft / loose soil including trimming sides and forming bottom surface to the required level / slope etc complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm in each layer as in soil complete all as specified and directed.

Removing excavated material (soil) to a distance not exc. 50 m and depositing where directed at a level not exc. 1.5 m above the starting point complete all as specified and directed.

M&L for sand cushioning with layer of sand 8cm thick before laying of cable and 15cm after laying of cable in trenches, punning complete all as specified and directed Note:- Punning thickness of 18 cm will be considered for payment.

M & L for laying brick as in protection covers over cables using sub class 'B' old size bricks laid flat, length wise perpendicular to the axis of cable complete all as specified and directed.

Laying only old serviceable bricks obtained from taking out old cables complete all as specified and directed.

Taking out old defective cable from trenches/ floor/road/wall/pipe/pole /service connections of any size , testing with LT magger , seggregating the serviceable part of cables and store for relaying complete all as specified and directed.

Supply and laying XLPE insulated screened PVC bedded, galvanised steel strip or wire armoured, electric power cable (heavy duty) with stranded aluminium conductor 1100 volt grade, laid in trenches/ducts, fixed on wall/inside panel, drawn through pipe of cross sectional area 10 Sqmm 2 core complete all as specified and directed.

All as per item No 96.00 here-in-before but cable size 10 Sqmm 4 core complete all as specified and directed.

All as per item No 96.00 here-in-before but cable size 16 Sqmm 2 core complete all as specified and directed.

All as per item No 96.00 here-in-before but cable size 16 Sqmm 4 core complete all as specified and directed.

All as per item No 96.00 here-in-before but cable size 25 Sqmm 4 core complete all as specified and directed.

All as per item No 96.00 here-in-before but cable size 50 Sqmm 3.5 core complete all as specified and directed.

All as per item No 96.00 here-in-before but cable size 95 Sqmm 3.5 core complete all as specified and directed.

All as per item No 96.00 here-in-before but cable size 120 Sqmm 3.5 core complete all as specified and directed.

All as per item No 96.00 here-in-before but cable size 185 Sqmm 3.5 core complete all as specified and directed.

All as per item No 96.00 here-in-before but cable size 240 Sqmm 3.5 core complete all as specified and directed. NOTE FOR ITEM NO 96.00 TO 96.09:- Quoted unit rates shall deemed included the making connections with necessary cable glands lugs etc as required.

Relaying only serviceable LT UG Cable obtained from Srl item No 17 of schedule any size and description including necessary cable glands lugs as required complete all as specified and directed. Note:- All relevent items like excavation, earth work, sand cushionning, bricks etc shall be measured and paid seperatly under respective items of this schedule.

M&L for Straight through joints heat shrinkble type 1.1 KV suitable for PVC insulated and sheathed aluminium conductor under ground cable of size 16 to 70 Sqmm 3.5 / 4 core including testing of joints after completion complete all as specified and directed.

All as per Ser item No 98.00 here-in-before but suitable for cable size of 95 Sqmm to 185 Sqmm, 3.5 core complete all as specified and directed.

All as per Ser item No 98.00 here-in-before but suitable for cable size of 240 Sqmm, 3.5 core complete all as specified and directed.

M&L Cutting of floor/wall/road/footpath for removal of LT U/G cable of any size/description and making good the same as per existing specifications after relaying of cable complete all as specified and directed.

M&L for Boring of holes under road /pavement/hard standing or any other situation by mannual means for 80/50 mm bore at the depth not less than 1 mtr below ground level for crossing the cable and making good both the ends complete all as specified and directed. Note :- GI pipe shall be measured and paid separately under respective item of this schedule.

S & F in replacement 50mm bore GI pipe light grade for cable protection, fixed to pole/ alongwall/ floor/ under road/ across the drain or nallaha etc complete all as specified and directed.

All as per Item No 103.00 here - in- before but 80 mm bore complete all as specified and directed.

All as per Item No 103.00 here - in- before but 100 mm bore complete all as specified and directed.

M & L fabrication of MS busbar chamber of nominal dimension 900 mm x 600 mm x 400 mm with 2 mm thick sheet duly provided with aluminimum busbar of size 50 mm x 6mm fixed on porcelain insulators TPN type out door weather/vermin proof with both way opening duly provided with neoprene rubber gasket along the doors openings pedestal type duly painted powder coated on CRCA steel sheet encloser with one No incommer MCCB 250 Amp 36 KA incl making connection /thimbles complete all as sepcified and directed.

Dismantling of LT PCC/steel tubular pole including demolition of pole coping, foundation etc and keeping serviceable insulators in safe custody for reuse complete all as specified and directed.

Supply and erection, in truly vertical position, LT Steel tublar swaged pole complete with cast iron base plate, finial taper plug, bolt , nut and screwed type 410-SP -31 (9 meters long ) Class -10 including painting of poles with two coats of synthatic enamel paint in black and white strips upto 1.5 mtr height from coping over a coat of red oxide primer including numbering of poles as directed. Make : Bansal/ Jindal/ National tube. Note : PCC, Earth work and MS work as cross arms clamps etc shall be measured and paid separately.

M&L for PCC type B1 1:2:4 (using 20 mm graded aggregate) as in coping to the poles with and including necessary form work as required complete all as specified and directed.

M&L for PCC 1:3:6 type C2 (using (40 mm graded aggregate) in foundation, filing and mass concrete complete all as specified and directed.

M&L for Cross arms, bracings, supports, clamps and back plates fabricated from structural steel sections including nuts, bolts, washers welding, bending cold or hot, drilling holes for bolts, in any hape or size as indicated or directed duly painted with two coats of synthic enamel paint over one coat of red oxide primer complete all as specified and directed.

Removal of Tree fallen on HT/LT overhead lines by cutting branches,bushes by electric cutter or manual and lifted by crane /Hydra/Manually including collection and depositing the retrieved timber at a place as directed by Engineer-in-charge.

Lopping / prooning of tree branches upto the extend to obtain clearance all around the LT over head lines / HT over head lines conductor upto 3 meters from furthest conductor on pole including removing of cut branches and cleaning of site complete all as specified and directed.

Opening the binding wire from pin /shackle insulator on steel pole of any height for re-stretching the ACSR conductor , after re-stretching without kinks & bends, binding the pin /shackle insulator with appropriate size of aluminium binding wire complete all specified & directed by Engineer-in- charge. NOTE: - Cost of binding wire deemed to be included in the quoted rate, No extra amount will be paid. One RM length will be measured for 03 phase and one neutral one street light and one earth wire.

Disconnection of electric connection from LT Panel of any size dressing of cable including replacement of burnt out aluminium lugs and fixing with new lugs, nuts bolt etc complete including all inter connection with aluminium strip of size not less than 0.6Mx0.03Mx6MM 1100 volts grade and suitable current rating including painting of Panels complete with inner & outer with two coats of synthetic enamelled paint over a coat of primer including excavation & earth work required for taking out & refixing the incoming and out going cable etc complete all as directed by Engr -in Charge; Note :-Replacement of unserviceable accessories parts shall be measured and paid separately under relevent items.

S&F in replacement MCCB 415 Volts 4 pole 630 Amps 50 Hz 50 KA of existing make model and type alonwith spreader terminal with adjustable thermal setting including lugs/thimbles of suitable size in existing panels complete all as specified and directed. Make of MCCBs - L&T/Legrand /Havells/C&S.

All as per Item No 116.00 but MCCB 400 Amp 36 KA 4 pole adjustable type 415 Volts 50 Hz. Complete all as specified and directed.

All as per Item No 116.00 but MCCB 250 Amp 36 KA 4 pole adjustable type 415 Volts 50 Hz Complete all as specified and directed.

All as per Item No 116.00 but MCCB 200 Amp 36 KA 4 pole adjustable type 415 Volts 50 Hz Complete all as specified and directed.

All as per Item No 116.00 but MCCB 125 Amp 25 KA 4 pole adjustable type 415 Volts 50 Hz Complete all as specified and directed.

S&F in replacement 1100 volts grade PVC insulated aluminium conductor screened served with inner sheathed in service connection flat twin core cable of size 10 sqmm complete all as specified and directed.

All as per item No 121.00 here-in-before but 06 sqmm twin core complete all as specified and directed

NOTES FOR ITEM NO 78.00 TO 122.00 : (i) Complaints pertaining to LT External Electric Supply shall be resolved by the contractor immediatelly after getting complaints. In case of failure on the part of contractor to resolve to the complaints within stipulated time, a penalty of Rs 1000/- per day per complaint shall be imposed from the contractor. (ii) The contractor or his authorised representative shall report to the concerned JE E/M at 0900 hours dailly on all working days to receive order/instructions of the work. A register shall be maintained to record all orders & instructions and their complaints and is to be signed by the contractor/his representative and the Engineer-in-charge/JE E/M concerned. (iii) Work done register to be maintained by the contrator. A separate Docket complaints slip book shall maintained by the contractor to note the complaints/jobs and get it signed by the user after completion of work and submits to the JE-in-Charge. NOTE FOR ALL ITEMS:-Tenderers may note that amount as given on schedule of credit will be deducted from the total amount arrived at the time of Acceptance of tender.

LEEJA ENTERPRISES

Ishtiaq and Sons

SONI ENTERPRISES

S S ELECTRICALS