SPECIAL REPAIR TO BLDG NO NP 204 SINGLE OFFRS ACCN P 427 OR MD ACCN AND CERTAIN SANCTIONED WORKS AT AHMEDABAD CANTT

Amount

Demolition of brick works or stone/boulder masonary, built in cement mortar or cement lime mortar including all quions, arches, pillars etc but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and as directed

Demolition of reinforced cement concrete (reinforcement cut as requried to facilitate demolition) of any description and in any position not otherwise specifically provided ie. Roofs, floors, beams , staircase, water tanks, chajjas and similiar suspended works etc complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors and paving n.exc 15cm thickness (below or above ground level) complete all as specified and directed.

Dismantling wall/floor tiling of any type or any thickness including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Taking down cement plaster of any description on brick or stone walls etc. including racking out joints hacking for key scrubbing down with water etc complete all as specified and directed.

Taking down chowkhats or frame with shutters (without taking off shutters from the frame) exc 1.5 sqm and n.exc 4.0 sqm each and remove from the site complete all as specified and directed

Taking down chowkhats or frame with shutters (without taking off shutters from the frame) n.exc 1.5 sqm each complete and remove from the site complete all as specified and directed

Taking down shutters of any description exc 1.00 Sqm and n.exc 2 Sqm each complete all as specified and directed.

Taking down shutters of any description exc 1.00 Sqm and n.exc 2 Sqm each and refixing the same opening including cutting easing as requried complete all as specified and directed.

Excavating in trenches, n.exc 1.5m wide & n.exc 1.5m in depth; for foundation, etc or for shafts, manholes, etc. n.exc 10 sqm on plan & n.exc 1.5 m in depth & getting out getting out in soft/loose soil complete all as specified and directed.

Returning, filling in, with excavated earth, including spreading, leveling, watering & well ramming in layers n.exc 25 cm thick complete all as specified and directed.

Removing excavated soil to a distance n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and as directed

M&L for excavation in post holes (or similar holes) n.exc 0.5 cum on plan and getting out, returning filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, Watering and removal surplus soil to a distance not exc 50m and making good surface all as specified (Soft / lose soil).

Removing excavated soil to a distance exc 500m and n.exc 1000m depositing where directed complete all as specified and as directed

M&L for hard-core of broken stone of gauge n.exc 63mm deposited, spread and leveled in layers n.exc 15cm thick watered and rammed to a true surface complete all as specified and as directed

M&L for plain cement concrete 1:4:8 type D2 (using 40 mm graded stone aggregate) as in foundation, fillings & mass concrete complete all as specified and directed.

M&L for plain cement concrete 1:3:6 type D2 (using 40 mm graded stone aggregate) as in foundation, fillings & mass concrete complete all as specified and directed.

M&L for PCC 1:3:6 type C-1 (using 20 mm graded stone aggregate) as hold fast bed blocks etc including weathering slightly rounded or chamfered angles and throating, including necessary form work complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in roof kerbs, coping, lintels, bands, benching, hold fast, cill etc including weathering slightly rounded or chamfered angles and throating, including necessary form work complete all as specified and directed.

M&L for RCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in slab supported on walls, beams, and columns in floors, roof, landings, balconies, canopies, deck slab and in shelves and the like etc complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating completed all as specified and directed.

M&L for providing precast cement concrete 1:2:4 type B 1 (using 20 mm graded stone aggregate) as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs, including slightly rounded or chamfers, weathering, throating etc and setting in CM 1:4 complete all as specified and directed.

M&L for RCC 1:1.5:3 nominal mix type A-1 (using 20mm graded stone aggregate) as in foundations, including rafts, footings, foundation beams, plinth beams; bases for columns; etc; basement lintels slabs shelves; under-reamed piles and mass concrete complete all as specified and directed.

M&L for RCC 1:1.5:3 nominal mix type A-1 (using 20mm graded stone aggregate) as in column, pillars, piers, post and struts etc complete all as specified and directed.

M&L for use and waste of formwork to sides of pillars, posts, struts, piers, columns & stanchions with rough finished surface of concrete complete all as specified and directed.

S&F TMT steel bars 10mm dia and over, cut to length bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends & binding with & including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

Ditto as above item No 26 but 6mm to 8mm dia as in spacers and binders

M&L for brick work with sub class 'B' bricks old size straight or curved on plan exc. 6 m mean radius built in cement mortar 1:6, complete all as specified and directed.

M&L for half brick thick walls with sub class 'B' bricks old size straight or curved on plan exc. 6 mtr mean radius built in cement mortar 1:4, complete all as specified and directed.

M&L for roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc and brushing neat cement slurry with 3.0kg per Sqm complete all as specified and directed.

M&L for non-skid ceramic coloured tiles, 7 to 8 mm thick as in floor area of each tile exc 0.06 Sqm but n.exc 0.11 Sqm, set and jointed in neat cement slurry and pointed in white or colored cement to match including screed bed or bedding layer of mortar 15mm thick in CM 1:6 in floors, complete all as specified and directed.

M&L for non-skid coloured ceramic tiles joints free 7 to 8 mm thick (square/rectangular) area of each tile exc 0.11 sqm but n.exc 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed or bedding layers of mortar 15mm thick in CM 1:6 in floors, complete all as specified and directed.

All as per above item No 32 but on vertical surface with backing of rendering 10mm th in CM 1:4

M&L for coloured vitrified tiles, light shade, joints free, 8 to 9 mm thick (square/ rectangular) polished, area of each tiles n.exc 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed or bedding layers of mortar 15 mm thick in CM 1:6 in floors, complete all as specified and directed.

All as per above item No 34 but on vertical surface with backing of rendering 10mm th in CM 1:4

M&L for glazed ceramic colored printed tiles of size 300 x 450 x 7 mm thick as in vertical surfaces of skirting/dado set and jointed in neat cement slurry and pointed in white or colored cement to match including 10 mm thick cement plaster with 1:4 cement mortar complete all as specified and directed.

M&L for machine cut kota stone slab flooring, staircase landing, treads of step in one piece, etc 20-25mm thick of any size laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing including screed bed or bedding layers of mortar 20mm thick in CM 1:6 in floors, complete all as specified and directed.

All as per item No 37 above but in vertical surfaces such as riser / step / skirting with 10mm thick backing coat in CM 1:4

M&L for machine cut kota stone slab as in shelves etc 20-25mm thick of any size fixed and jointed with grey cement slurry including rubbing and mirror polishing including cutting grooves in walls for inserting kota stone slab of size 50 x 50mm and making good, complete all as specified and directed.

M&L for UDAIPUR GREEN MARBLE 20-25 mm thick laid and jointed with grey cement slurry incl. rubbing and polishing with mirror finish over and including 20 mm thick screed bed in CM 1:6 complete all as specified and directed.(Note: All exposed side of stone slab shall to be rounded)

M&L for 75mm thick PCC 1:4:8 type D2 (using 40mm graded stone aggregate) as in sub base complete all as specified and as directed

M&L for 18-20mm thick machine cut Granite, mirror polished, in skirting / dado laid over cement screed and jointed with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete or coloured cement to match including 10mm thick backing coat of tiles in CM (1:3) complete all as specified and directed.

M&L for screed bed or bedding layers of mortar 20mm thick in CM 1:6 for laying kota - tiles floor complete all as specified and directed.

M&L for 40mm thick PCC 1:2:4 type B-1 (using 20mm graded aggregate) as in floor, surface finished even and smooth without using extra cement complete all as specified and directed

M&L for chequered coloured cement concrete tiles 30cm X 30cm X 25mm thick set and jointed and pointed in neat cement slurry with grey cement and pigment in floors / paths over and including 15mm thick cement screed bed in CM (1:6) complete all as specified and as directed .

M&L for rendering 10mm thick in CM 1:6 on fair faces of brick masonary/concrete surfaces finished even and smooth without using extra cement complete all as specified and directed .

M&L for rendering 10mm thick in CM 1:4 on brick masonary, surfaces finished even and smooth without using extra cement complete all as specified and directed .

M&L for 10 mm thick rendering in cement mortar 1:3 on concrete surfaces of ceiling , finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for plain cement concrete 1:5:10 type E 2 (using 40 mm graded stone aggregate) as in concrete bed of sunken floor fillings & mass concrete complete all as specified and directed.

M&L for 15 mm thick rendering in cement mortar 1:3 mixed with and including approved water proofing compound on concrete/ plastered surfaces of sunken floor & RCC tanks etc. including M & L for applying two coats of epoxy coating over plastered surface complete all as specified and directed.

M&L for 15 mm thick rendering in cement mortar 1:4 mixed with and including approved water proofing compound on fair faces of brick work / concrete etc. including M & L for providing and fixing Chicken mesh complete all as specified and directed.

M&L for 75mm thick cement concrete 1:3:6 type C-1 (using 20mm graded stone aggregate) as in floor-plinth protection including necessary form work and finishing surface even and smooth without using extra cement including forming construction joints at interval of 3.0m, 6mm wide and filling the same with bitumen mastic complete all as specified and as directed .

S&F mild steel angle iron work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors , door chowkhats etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive or steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete Fe290 (Gde-E-165) complete all as specified and directed.

S&F 35mm thick flush shutter, solid core construction with particle board core and plywood face panels commercial type on both sides compete all as specified and directed.

S&F 35mm thick IInd class hardwood factory made glazed and skeleton shutters, open rebated & prepared to receive glass, gauze, etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut mitred beads for securing glass, etc size of members as specified in SSR Pt-I, section 8 clause 8.20 (a) complete all as specified and directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube all as per specifications and as per drawing shown on sl page No 150 of SSR Part-II (for item 884) and fixing with suitable screw/dash bolt of size 100mm long complete all as specified and directed.

S&F factory made solid panel PVC door / CB shutter 30mm thick (Style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles & plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail ; panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading & jointed together with solvent cement, supply & fixing in the frame at site as per SSR specifications & diagram/product drawing shown on sl page No 146 of SSR Part II with the size of door shutter as required & directed by the Engr-in-Charge.

S&F 100mm long hasp and stapple, safety type, aluminium anodised with mild steel hinge pin including bolt plate and fixed with screws complete all as specified and directed.

S&F 150 mm long aluminium anodized barrel tower bolts of extruded section complete all as specified and directed.

S&F 250mm long aluminum alloy anodized sliding door bolts with hasp and staple (bolt type) and fixed clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminum alloy and fixed complete all as specified and directed.

S&F 100mm long stainless steel butt hinges medium weight cold rolled complete all as specified and directed.

S&F 150mm long aluminium handle extruded aluminium alloy, fabricated type complete all as specified and directed.

S&F stainless steel wire mesh 0.36mm dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staple/beads etc complete all as specified and directed.

M&L for cutting the cracks in V section of size 5 to 7 mm wide, cleaning , filling surface cracks with “Dr fixit cracks X power or equivalent polymer modified cracks filler all as per manufacturer instructions complete all as specified and directed.

M&L for cutting holes in brick walls in brick walls built in cement mortar for inserting hold fasts of length exc. half brick but n.exc one brick wall and making good dismantled portion in CM 1:3 or cement concrete 1:2:4 type B-1 as required, all as specified and directed.

S&F steel window with side hung shutters, box type hinges, pressed steel handles, MS tower bolt 100m long 2 nos in each leaf, steel peg stay, lugs, with glazing bars dove tailed or welded, all as shown in Drg no CEBZ/TD/22 complete all as specified and directed.

S&F steel window with side hung shutters, box type hinges, pressed steel handles, MS tower bolt 100m long 2 nos in each leaf, steel peg stay, lugs, with out glazing bars dove tailed or welded, all as shown in Drg no CEBZ/TD/22 complete all as specified and directed.

S&F framed work as in grills, gratings, guard bars of windows, ladders etc with ends of bars shouldered and/or riveted, fixed independently in steel frames and similar articles conforming to Fe-290, Gde E-165 complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden or metal frame including punching or drilling out old glazing pins/ springs clips complete all as specified and directed.

S&F 4 mm thick plain sheet glass, ordinary quality and glazing with oil putty in square n.exc 0.5 sqm in each pane complete all as specified or directed

S&F 4 mm thick figured glass, pin headed type, ordinary quality and glazing with oil putty in square n.exc 0.5 sqm in each pane complete all as specified or directed

S&F anodized aluminium alloy sections sliding windows with frames Series-C (20mm) of Jindal or equivalent and, two track sliding shutters duly fitted with neoprene beading, glazing clips, two shutters including tinted glass panes 5.0 mm nominal thickness, aluminium alloy handles/ lock etc. complete all as specified and directed. Note :- Thickness of chowkhats /frame section and sliding shutter section shall be minimum 1.5 mm

S&F anodized aluminium alloy sections sliding windows with frames Series-C (20mm) of Jindal or equivalent and three track sliding shutters with AC opening duly fitted with neoprene beading, glazing clips, two shutters including tinted glass panes 5.0 mm nominal thickness one shutter with stainless steel wire cloth 0.45mm dia and average width of aperture 1.4mm , aluminium alloy handles/ lock etc. complete all as specified and directed. Note :- Thickness of chowkhats /frame section and sliding shutter section shall be minimum 1.5 mm

S&F anodized aluminium door frame with section size 100 x 44 x 1.98mm thick with one or more rebates and shutters pull and push type or side hung type (with or without aluminium sash bars) comprising of top & lock rails of section 115 x 44 x 1.98 mm thick, bottom rail of section 150 x 44 x 1.98mm thick and stiles of section 85 x 44mm x 1.98mm thick including necessary jointing cleat, glazing clip, rubber packing anodized aluminium beading, screws, stainless steel hinges100mm, anodized aluminium fittings with handles 'D' type 125mm long, floor door stoppers, tower bolt 200 mm, sliding door bolt 300 mm long, hydraulic door closer, mortice lock, 5.0mm thick tinted or frosted glass /12mm th preleminated particle board (Novapan) panel and making good of wall surface to match existing surface complete all as specified and as directed,

S&F aluminium anodized ventilator with aluminium frame of size 65 x 40 x 1.98mm thick, fixed in vertical position, partially glazed partially louvers i.e. including half portion to be provided with 4mm thick pin head glass and remaining portion to be louvered using 4mm thick pin head glass and louvered portion covered with stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm incl necessary channel frame work, including rubber gasket and aluminium beading complete all as specified and directed Note : The quoted rate shall included for provision of 4mm thick glass, glass louvers & stainless steel wire cloth.

S&F aluminium anodized ventilator with aluminium frame of size 65 x 40 x 1.98mm thick, fixed in vertical position, partially glazed partially louvers i.e. including half portion to be provided with 4mm thick pin head glass and remaining portion to be louvered using 4mm thick pin head glass incl necessary channel frame work, including rubber gasket and aluminium beading complete all as specified and directed Note : The quoted rate shall included for provision of 4mm thick glass, glass louvers

M&L for aluminium deco grill medium grade of mesh size 75mm x 75mm with 6mm square anodized aluminium bars fixed with aluminium frame of size 37 x 19 x 2mm complete all as specified & directed

Dismantling of fencing post or struts (wood, steel, RCC) any section, post embedded in concrete, brick work, masonry etc including taking out embedded portion and making good disturbed ground complete all as specified and directed

Dismantling of barbered wire of any size any description fixed on posts of any kind all as in fencing.

Dismantling wrought iron or mild steel work of any description not otherwise provided for

S&F MS work in roof truss (framed), trusses, purlins, rails and fastenings and heavy bracket, framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats etc with Fe 410-W (Gde -E- 250) complete all as specified and directed.

S&F hand rails, half round or other steel section, nosing to steps including embedding in concrete and screwing etc. wind ties for roof including securing bolts; fencing posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.), and similar work conforming to Fe 290 gde E 165 complete all as specified and directed.

S&F steel work in tubular trusses, purlins, including special shaped washer etc, complete using ERW or induction butt welded tubes conforming to IS 1161-1998 grade St-240, including distances pieces, base plates, nut bolts etc including complete all as specified and directed.

Dismantling wall and ceiling boards any thickness including cover fillets complete all as specified and directed.

M&L for false ceiling, at any height, of 600 x 600 x 15mm mineral fibre ceiling tiles of type micro look edge laid on fixed with and including / laid on GI based super fine XL 15mm exposed grid system with 15mm wide T-section flanges. The frame work comprises of main runner of size 15 x 32mm spaced at 600mm centre securely fixed to the structural soffit by approved hangers at 1200mm maximum centres. Hangers (GI wire 4mm dia) to be fixed by approved roof plug, level adjustment and screws etc and making good disturbed surfaces, complete all as specified and directed.

S&F mild steel as in bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required; hooks (stay), heavy, for large gates; hook & pintle hinges; large hasps & staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hook for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; plate washers & similar small articles conforming to Fe 290 GDE E-165 complete all as specified and directed.

S&F welded steel wire fabric of weight exc 4 Kg per Sqm fixed to steel members complete all as specified and directed.

Fixing only chain link fencing including line wires, any mesh size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire. complete all as specified and directed.

Supply only chain link fencing any size any type (Approx size 75mm x 75mm x 3mm dia) etc complete all as specified and directed.

S&F galvanized, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacing and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanized mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured)

Dismantling asbestos cement (corrugated or semi corrugated, etc) sheets in roof covering complete all as specified.

S&F pre-painted galvalume aluminium zinc coating plain steel sheet 0.50mm thick of any colour (as approved by GE) having tensile strength of 550 Mpa as in ridges, hips, valley gutters, drip and straight flashing cut to length & bent to shape required, fixed using hot dip galvanized, self drilling and self tapping screws of suitable size including neoprene and EPDM washers complete all as specified.

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour (as approved by GE) having tensile strength of 550 Mpa as in roof covering / clading to wall, fixed with self tapping screws complete all as specified and directed. Note :- Corrugation shape of sheet shall be approved by GE.

M&L for complete removal of existing treatment of any type of paint on walls complete all as specified and as directed .

M&L applying 3 mm thick (maximun and average 1.50mm) wall care putty on wall and smoothening the surface complete all as specified and as directed.

M&L for applying two coats of oil emulsion distemper, white or tinted over a coat of primer on wall complete all as specified and as directed .

M&L for two coats of cement base paint on plastered surface including one coat of primer on wall and ceiling complete all as specified and as directed.

M&L for applying two coats of synthetic enamel paint over a coat of pink primer on wooden surface including preparation of new wooden surfaces complete all as specified and directed.

M&L for applying two coats synthetic enamel paint over a coat of red oxide primer on new steel surfaces of any description over 10cm width or girth including preparation of surfaces complete all as specified and directed.

M&L for preparation of old painted steel surface of any description over 10 cm width or girth and applying two coat of synthetic enamel paint complete all as specified and directed

M&L for white washing three coats to wall surfaces including preparation of newly plastered untreated surfaces complete all as specified and directed.

M&L for white washing two coats to wall surfaces including preparation of old plastered untreated surfaces complete all as specified and directed.

M&L for preparation of old plastered surfaces of ceiling (plastered or unplastered) / AC sheet including cornices etc. and applying one coat of white wash complete all as specified and directed.

Taking up or down 15mm bore steel tubing and connections, including cleaning for re-fixing or removal to store

Taking up or down 20mm bore steel tubing and connections, including cleaning for re-fixing or removal to store

Taking up or down 25mm bore steel tubing and connections, including cleaning for re-fixing or removal to store

S&F 15mm bore tubes, `medium grade', galvanized concealed/ surface on walls, with all fittings and fixed to walls and ceilings or laid in floors complete all as specified and directed..

S&F 20mm bore tubes, `medium grade', galvanized concealed/ surface on walls, with all fittings and fixed to walls and ceilings or laid in floors complete all as specified and directed..

S&F 25mm bore tubes, `medium grade', galvanized concealed/ surface on walls, with all fittings and fixed to walls and ceilings or laid in floors complete all as specified and directed..

S&F 15mm dia, brass, chromium plated mixer for hot and cold, fancy type, screwed down, screwed for iron pipe, fixed in repair/new complete all as specified and directed.

S&F 15mm dia Bib taps, cast copper alloy, chromium plated fancy type, screwed down, screwed for iron pipe or for brass ferrule and fixed in repair complete all as specified and directed.

S&F 15mm dia stop valves (concealed type), cast copper alloy, fancy type chromium plated screwed down high pressure, screwed both ends for iron pipe or for unions and fixed in repair complete all as specified and directed.

S&F 15mm dia fancy stop valves (concealed type), cast copper alloy, screwed down high pressure, screwed both ends for iron pipe or for unions and fixed in repair complete all as specified and directed.

S&F pillar taps 15mm, fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed.

S&F in repair 125mm dia size PTMT shower rose with or without swivel complete all as specified and directed.

S&F in repair 20mm dia bore ball valve brass, high pressure with polythene float and fly nut complete screwed for or in pipe or brass ferrule complete all as specified and directed.

S&F PVC bathroom mirror cabinet of size 450mm x 600mm with mirror fixed with brass screw complete all as specified and directed.

S&F in repair health faucet spray type jet with brass jet, chromium plated, and 1.5m long PVC flexible pipe complete all as specified and directed

S&F vitreous china wash down water closet pan (Pedestal pattern) coloured including fixing bolt and plastic water closet seat black closed pattern with flat bottom cover with MS chromium plated hinging devices to matching colour complete all as specified and directed.

S&F in repairs vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests including lime concrete bedding complete all as specified and directed.

S&F in vitreous china coloured counter top wash basin oval white 195 x 590 x 420mm including , brass CP waste coupling, PTMT connection pipe 450mm long etc. complete all as specified and directed.

S&F in vitreous china white /coloured wash basins flat back 550 x 400mm including Mild steel brackets, brass CP waste coupling 32mm dia, PVC waste pipe, PTMT connection pipe 450mm long etc. complete all as specified and directed.

S&F in repairs PVC valve less 10 ltrs capacity syphonic action type flushing cistern low level, white with inlet, ball valve float and handle including brackets and 32 mm dia polyethylene flush pipe complete all as specified and directed.

S&F in repairs PVC connection 450 mm long of dia 15 mm, PTMT nuts complete all as specified and directed.

S&F in repair tubular towel rail 20mm dia 100cm long including brackets fancy type brass chromium plated complete all as specified and directed

S&F tubular towel ring 20mm dia and 23cm dia including brackets fancy type brass chromium plated complete all as specified and directed

S&F in repair kitchen sink made of stainless steel 1mm thick with plugs, washers and wastes; including bedding in cement mortar on the dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm, bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S&F stainless steel tubular curtain rod 25mm dia, 18 gauge decorative along with stainless steel decorative type brackets all as specified and as directed.

M&L for welding in repair, length n exc 2.5 cm and thickness of metal to be welded nexc 6mm thick complete all as specified and directed.

S&F 75 mm bore CI soil, waste and vent pipes, sand cast, in any length, with or without ears, with cement jonts fixed to wall complete all as specified and directed.

S&F 100 mm bore CI soil, waste and vent pipes, sand cast, in any length, with or without ears, with cement jonts fixed to wall complete all as specified and directed.

S&F in repair 75 mm bore CI bends (any radius), diminishing pieces or tapers (larger bore measured) with oval access door complete all as specified and directed.

S&F in repair 75 mm bore CI bends (any radius), diminishing pieces or tapers (larger bore measured) without oval access door complete all as specified and directed.

S&F in repair 100 mm bore CI bends (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified and directed.

S&F in repairs 100 mm bore CI branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified and directed.

S&F 75 mm dia bore CI vent cowl complete all as specified and directed.

Taking down eaves gutter and rain water pipe any size any pattern, PVC , AC pipe including all fitting, heads shoes, bends etc including removal to store complete all as specified and directed

S&F in repairs Stainless steel square grating 150mm size for trap complete all as specified and directed.

M&L for PCC 1:2:4 type B-O (using 12.50 mm stone aggregate) as in, leveling coarse complete all as specified and directed.

Fixing only steel gate of area exc 2 Sqm but not exc 4 Sqm and weight not exc 200 Kg each including providing necessary hold fast etc complete all as specified and directed.

M&L for water proofing treatment to non accessible RCC roofs slabs by providing 10mm thick screed bed in CM 1:3 mixed with & including water proofing compound @ 3% by weight of cement & then applying one coat of cold bituminous primer @ 0.30 kg/sqm and confirming to IS-3384, laying APP based polymer modified membrane reinforced non wooven polyester of weight 3 kg/sqm, minimum 3 mm thick, minimum with plain polythene finished and sealing all over laps 75 mm in length side and 100 mm width sides of membrane by torching the same joint of member shall be treated with one coat of bitumen (85/25) @ 1.20 kg/sqm, & applying two coats of aluminium paint complete all as specified and as directed

M & L for guniting for shortcrete in CM 1:2 mixed with epoxy resin and hardner @ 2% by weight of cement in equal proportion using shaortcrete pumps and allied equipment in thickness 30mm all as per manufacturers instruction complete all as specified and directed. Make of Epoxy resin hardner :- Fosroc / MC Bauchemic / Cico / Pidilite

S&F 1000 litres capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position incl 20mm ball brass valve high pressure, with polythene nut and fly nut complete, screwed for iron pipe or brass ferrule and fixed all as specified in SSR Part I complete all as specified and directed.

Dismantling of existing PVC water tanks carefully from roof surface of capacity exc 500 litres and n.exc 1000 litres and refixing the same after completion of water proofing work including providing of necessary new fittings like elbow, tee, socket etc. complete all as specified and directed by Engr-in-Charge.

S&F glass corner shelf of size 3000x300mm (3 their) complete all as specified and as directed. Make- Jaguar/commander/Prayag / Marc

All as per item No 146 above but 2 tirer shelf

S&F glass self of size 450x150mm fuixes to wall ect complete all as specified and as directed

S&F hand shower brass chromium plated, 75 mm dia (minimum) with 8 mm dia and 1500mm long flexible tube and wall hook complete all as specified and directed. Make : Jaquar / Plumber / Kholer / Somany / Cera.

S&F in repairs chromium plated soap dish cat No MAOR-4050 of Marc or equivalent of Jaquar / Plumber / Kholer / Somany / Cera.

S&F in repairs chromium plated toilet paper holder complete all as specirfied and as directed. Make : Jaquar / Plumber / Kholer / Somany / Cera.

M&L 12mm thick rendering cement plaster on brickwork or concrete surfaces in cement mortar 1 : 6, finishing the surfaces even and fair complete all as specified and directed.

M&L 12mm thick rendering cement plaster on brickwork or concrete surfaces in cement mortar 1 : 4, finishing the surfaces even and fair complete all as specified and directed.

S&F butt hinges 100mm size medium weight cold rolled mild steel.

S&F in repairs stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.4mm fixed to steel windows / wooden doors fixed with GI wire staples all as specified and directed.

S&F in repairs figured glass 4mm thick pin headed type and glazing with oil putty / beads in square not exc 0.50 Sqm in each pane, all as specified and directed.

S&F hold fasts and similar small articles conforming to Fe410-0 or Fe 310-0.

M&L providing, cement concrete type C-I 1:3:6 (using 20mm graded aggregate) as in bed plaets (for hold fast) etc complete all as specified and directed.

S&F 25mm dia fancy type depary curtain rods with suitable fancy type brackets to both ends as required fixed in repair complete all as specified and directed.

Dismantling of cement concrete of any description over roof and removing the rubbish off premises out side of MD land complete all as specified and directed.

Taking down carefully surface aluminium point wiring with PVC casing-capping (light, fan, socket, bell or power) including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc and making good disturbed surfaces complete.

Taking down MCB distribution boards with incoming and outgoing controls any make, any capacity after disconnecting complete.

Taking down carefully sub main wiring with wooden batten / PVC surface conduit and making good disturbed surfaces complete all as directed

M&L for point wiring with 1100 volts grade PVC insulated FR multistranded copper conductor cable 1.5 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 1.0 sqmm (Green) drawn into and including concealed rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and sunken galvanized pressed steel terminal boxes and modular mounting plates for mounting switches, sockets, fan regulators etc. complete for the following :-

One light point controlled by one switch.

One light point controlled by two, two way switches.

One fan point controlled by one switch.

One socket outlet 6 amp controlled by one switch on independent board.

One socket outlet 6 amp controlled by one switch on same board with other switches.

One bell point controlled by one bell push switch

M&L for point wiring with 1100 volts grade PVC insulated FR multistranded copper conductor cable 2.5 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 1.5 sqmm (Green) drawn into and including concealed rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and sunken galvanized pressed steel terminal boxes and modular mounting plates for mounting switches, sockets as required.

S&F modular switch piano button single pole one way 6 amp 1 module all as per Legrand Mylinc Cat Ref No 675501 or equivalent in Schneider Zencalo or MK Blanze as approved.

S&F modular switch piano button single pole two way 6 amp 1 module all as per Legrand Mylinc Cat Ref No 675501 or equivalent in Schneider Zencalo or MK Blanze as approved.

S&F modular switch piano button single pole one way 16 amp 1 module all as per Legrand Mylinc Cat Ref No 675511 or equivalent in Schneider Zencalo or MK Blanze as approved.

S&F modular socket outlet 2 in 1, 2 & 3 pin, 6/16 amp, combined 2 module all as per Legrand Mylinc Cat Ref No 675555 or equivalent in Schneider Zencalo or MK Blanze as approved.

S&F modular socket outlet 2 in 1, 2 & 3 pin, 6 amp, combined 2 module all as per Legrand Mylinc Cat Ref No 675550 or equivalent in Schneider Zencalo or MK Blanze as approved.

S&F modular hum free electronic step fan regulator 100 Watt, 2 module all as per Legrand Mylinc Cat Ref No 675530 or equivalent in Schneider Zencalo or MK Blanze as approved.

S&F modular switch bell push single pole one way 6 amp 1 module all as per Legrand Mylinc Cat Ref No 675504 or equivalent in Schneider Zencalo or MK Blanze as approved.

M&L for point wiring with 1100 volts grade PVC insulated FR multistranded copper conductor cable 2.5 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 1.5 sqmm (Green) drawn into and including concealed rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and sunken galvanized pressed steel terminal boxes and modular mounting plates for mounting switches, sockets as required.

M&L for point wiring with 1100 volts grade PVC insulated FR multistranded copper conductor cable 1.5 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 1.0 sqmm (Green) drawn into and including concealed rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and sunken galvanized pressed steel terminal boxes of thickness not less than 1.20mm covered with 3mm thick phenolic laminated white sheet for mounting switches, sockets, fan regulators etc as required complete all as specified and directed for the following :-

One light point controlled by one switch.

One fan point controlled by one switch.

One socket outlet 6 amp controlled by one switch on the same board with other switches.

One socket outlet 6 amp controlled by one switch on independent board.

One bell point controlled by one bell push switch.

M&L for point wiring with 1100 volts grade PVC insulated FR multistranded copper conductor cable 2.5 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 1.5 sqmm (Green) drawn into and including concealed rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and sunken galvanized pressed steel terminal boxes of thickness not less than 1.20mm covered with 3mm thick phenolic laminate white sheet for mounting one 16 amp switches, sockets out lets etc as required complete all as specified and directed for one 16amp socket outlet controlled by one switch on independent board

Supply and fix angle holder 240V insulated Polycarbonate body with back plate complete

S&F switch piano flush type single pole one way 6 amp 240V complete

S&F bell push switch piano flush type single pole one way 6 amp 240V complete

S&F switch piano flush type single pole one way 16 amp 240V complete

S&F socket out let 2 in 1, 3 pin 6 amps 240V complete

S&F socket out let 2 in 1, 3 pin 6 & 16 amps 240V complete

S&F ceiling rose 3 plates 240V polycarbonate isolated body complete

S&F hum free electronic step fan regulator 120 - 280 volts of 100 watt capacity (socket type) including connecting up complete

S&F door bell ding dong, AC, 240V, Single pole complete all as specified and directed Make: Havells Reo / Anchor Penta PC / SSK as approved.

M&L for submain wiring with 2 Nos 6 sqmm + 1 Nos 4 sqmm earth continuity wire PVC insulated FR multistranded copper conductor cable (Phase - Red, Neutral - Black, Earth - Green) drawing into and including concealed rigid non metallic 20mm dia PVC conduit, medium grade, ISI marked ivory colour along with accessories of following size PVC conduit complete all as specified and directed (Note:- Three run of cables including PVC conduit its accessories and chases and its making good shall be measured and paid as one length).

M&L for submain wiring with 2 Nos 4 sqmm +1 Nos 2.5 sqmm earth continuity wire PVC insulated FR multistranded copper conductor cable (Phase - Red, Neutral - Black, Earth - Green) drawing into and including concealed rigid non metallic 20mm dia PVC conduit, medium grade, ISI marked ivory colour along with accessories of following size PVC conduit complete all as specified and directed (Note:- Three run of cables including PVC conduit its accessories and chases and its making good shall be measured and paid as one length).

S&F in repair energy efficient recessed mounted LED luminaries suitable for 2` X 2` grid ceiling with flat diffuser and lumen output of 3300 lumens having constant current electronic driver duly connected with 0.5 sqmm white colour PVC insulated & sheathed three core flexible multi stranded copper conductor cable, complete all as specified and directed. Fitting shall be of Philips Cat ref no. RC365B LED 33-5000P SU OD WH or equivalent inGE Lighting Cat no GCR036.56M1 or Wipro as approved complete.

Supply and fix LED bulk head fitting 9 watt , IP 66 & IK 09 with pressure die cast aluminium housing & polycarbonate diffuser duly prewired for connection with flexible multistranded copper conductor including lamp complete all as specified and directed . Fitting shall be of make Philips cat ref No. WT 202 W LED 6S CW PSU S1 PC or equivalent of GE lighting or Wipro as approved

Supply and fix LED batten 1.2m length, made of CRCA sheet housing with a PC glossy diffuser duly prewiried connection having a nominial system lumen output of 2000 lumens at a minium system efficacy of 105 lumen per watt and total power consumption not more than 19 watt including driver, it shall be rated system life of 40000 burning hours at L70 and should have a color temperature of 6500K, CRI > 80, THD< 10% and PF> 0.95 including lamp complete all as specified and directed . Fitting shall be of make Philips cat ref No. ENDURALED BATTEN "BN 108C LED 20S PSU CDL WH" or equivalent of Wipro or GE lighting as approved

Supply and fix LED fitting 8 watt duly prewired for connection with flexible multistranded copper conductor including lamp complete all as specified and directed. Fitting shall be of make Philips cat ref No. LED Linea BN 550 WLED 6 6500 or equivalent of GE lighting or Wipro as approved

S&F MCBs as per load requirement 'C' series of breaking capacity 10 KA, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs of following ratings:-

Single pole 6 to 32 amp Make -Legrand cat ref No 408587 to 408595 or equivalent in Hager or Schneider as approved.

Double pole and neutral 10 to 32 amp Make -Legrand cat ref No 408631 to 408636 or equivalent in Hager or Schneider as approved.

Double pole and neutral 63 amp Make -Legrand or equivalent in Hager or Schneider as approved.

S&F powder coated, CRCA steel sheet MCB distribution board constructed as per IS : 8623, degree of protection IP 43 - IK 09 with metal door, recess mounted, having insulated 100 amp tinned copper bus bar, neutral busbar, earth bar, din bar, detachable gland plate, interconnection, earthing connection, blanking plates in unused spaces etc as required of following ratings & ways:-

SPN, 240 volts, 8 ways Make:- Legrand cat ref no 607711 or equivalent in Hager or Schneider as approved.

TPN, 415 volts, 4 ways Make:- Legrand cat ref no 607715 or equivalent in Hager or Schneider as approved.

S&F powder coated, CRCA steel sheet MCB distribution board ETPN, 415 volts, 4 way, constructed as per IS : 8623, degree of protection IP 43 - IK 09 with metal door, recess mounted, having insulated 100 amp tinned copper bus bar, neutral busbar, earth bar, din bar, detachable gland plate, interconnection, earthing connection, blanking plates in unused spaces etc as required. Make:- Legrand or equivalent in Hager or Schneider as approved.

M & L for pipe in pipe chemical Earthing with GI pipe electrode 3.0 m long having outer pipe nominal dia 80 mm & inner pipe nominal dia 50 mm duly filled with highly conductive and anticorrosive compound of required quantity having chemical composition Bentonite 40% , copper sulphate 20% , gypsum 5% , graphite 10% , Alum 5% , Zinc sulphate 10% Aluminium sulphate 10% burried in ground by digging a bore of 150 mm dia surrounded by soil friendly backfill compound non soluble in water including connections with galvanised earth wire 4 mm dia from main MCB DB protected in 15 mm dia GI pipe light grade making PCC pit of size 0.3 m x 0.3 m x0.3 m (inner size ) in mix 1:3:6 type C1 with RCC 1:2:4 type B1 , 40 mm thick reinforced with 8mm dia MS wires 3 Nos both sides with lifting hook made out of 8 mm dia bar and testing on completion to achieve valve not more than 1.0 ohm complete.

Supplying, laying or fixing or passing through pipe, testing and commissioning 1100 volts grade ISI marked XLPE insulated and PVC sheathed steel tape / wire armoured underground stranded aluminium conductor cable cross sectional areas 10 sqmm 4 core, including complete all as specified and directed. Make - Havells / Polycab / Finolex / Universal as approved- Note :- Excavation & Earthwork, sand cushions & brick protection shall be measured & paid separately.

Supplying and laying old size bricks, common burnt clay building bricks sub class 'B' designation 75 complete.

M&L for sand filling in trenches with clean dry fine sand unwashed including gently punning around cables complete. Note:- Punned down thickness shall be measured and paid.

S&F steel tubes light grade galvanized 40 mm dia bore, ISI marked, with all fittings fixed to walls / floors / road crossing, poles as required for cable protection including necessary clamps, holder etc complete all as specified and directed.

S&F power unit for AC or geyser 3.5 KW 4 module including sunken modular GI metal boxes not less than 1.2 mm thick and white modular mounting plates with frame all as per Legrand Mylinc cat ref No 675558, 689009, 675564 & 675584 or equivalent in Schneider Zencelo or MK Blenze as approved.

Renewal of any type street light junction box with thermoplastic, IP 65 cable junction box with metric knockouts on all sides for cable entry size: 200 x 160 x 98 mm as per Hensel cat ref No. K 9250 or equivalent in Eaton or Rittal or Secure duly fitted with followings:-

One number DIN Rail (35 mm).

Four numbers ELMEX or equivalent make connector of 10 sqmm.

One number ELMEX or equivalent make end plate.

Two numbers ELMEX or equivalent make end clamps.

One number MCB SP 6 amp, 10 KA, 'C' series of Legrand make (cat ref no 408587) or equivalent in Hager or Schneider as approved.

S&F post top LED lanter with diffuser and painted spun aluminium deflector including connection from junction box to light fitting having system wattage 20W, all as per C & S electric Cat ref no LTGLC20WHPLED/W or equivalent in Philips or Wipro as approved.

S&F MCB distribution board SPN, 240 volts, 8 ways powder coated, CRCA steel sheet constructed as per IS : 8623, degree of protection IP 43 - IK 09 with metal door, recess mounted, having insulated 100 amp tinned copper bus bar, neutral busbar, earth din bar, detachable gland plate, interconnection, earthing connection, blanking plates in unused spaces as required.

Shreeganesh Construction

nirman construction

SNEH TRADERS

Ramdev and Sons